Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Demolition of stone slabs and tiles of any description or thickness in floors & wall, laid bedded & pointed in any mortar complete all as specified and directed. |
| 2 | Roughening of old unservicable PCC floorsurface by picking, chipping and wire brush sweeping clean and washing down with water to remove dust outside to make it suitable for laying floor tile complete all as specified and directed. |
| 3 | Demolition of cement concrete (unreinforced) in ground floor and pavings not exc15 cm thickness (below or above ground level) and removing from site complete all as specified and directed. |
| 4 | M&L for 25 mm thick PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate in sub floors complete all as specified and directed. |
| 5 | M&L fornon skid coloured ceramictile 7 to 8 mm thick area of each tileexceeding0.11 sqm but not exceeding 0.18 sqm , as in floors etc set over and including screed bed or bedding layer of mortar 15 mm thick for laying floor finishes with CM 1:4 (Tile pattern and decoration may be as suggested by Engineer-in-charge) complete all as specified and directed. |
| 6 | M&L fornon skid coloured ceramic tile 7 to 8 mm thick area of each tileexceeding0.18 sqm but not exceeding 0.38sqm, as in floors etc set over and including screed bed or bedding layer of mortar 15 mm thick for laying floor finishes with CM 1:4(Tile pattern and decoration may be as suggested by Engineer-in-charge) complete all as specified and directed. |
| 7 | M&L fornon skid colour ceramictile 7 to 8 mm thick area of each tile exceeding0.18 sqm but not exceeding 0.38 sqm, as in skirting etc set over and including 10 mm thick rendering withCM 1:3 (Tile pattern and decoration may be as suggested by Engineer-in-charge) complete all as specified and directed. |
| 8 | M & L for Glazed ceramic coloured walls tilesin vertical surfaces 300 x 450x 6mm to 7 mm thick set over and including rendering on vertical surface of wall or concrete surfacesin CM 1:3 to receive wall tiles (Tile pattern and decoration may be as suggested by Engineer-in-charge) complete all as specified and directed. |
| 9 | M & L for 18 to 20 mm thick machine cut green marbel stone in single piece in window/opening (Jambs/Cills) laid over cement screed and jointed withbase laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete including 10 mm thick plastering with cement mortar 1:3 complete all as specified and directed. |
| 10 | M&L Granite (of any type and colour) work (table rubbed and polished) 18 to 20mm thick in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match complete all as specified and directed. |
| 11 | M & L for machine cut kota stone slab flooring in landings of staircase & treads of steps etc. of 20 - 25mm thick (the stone may be in one piece) including rubbing and polishing complete set over and including screed bed or bedding layer of mortar 15 mm thick for laying floor finishes withCM 1:4 complete all as specified and directed. |
| 12 | M & L for machine cut kota stone slab20 - 25mm thick in skirting, riser of steps etc (the stone shall be in one piece) including rubbing and polishing complete set over and rendering for screed bed on vertical surface of wall or concrete surfaces in CM 1:3 to receive wall tiles complete all as specified and directed. |
| 13 | Taking down chowkats or frame with shutter (without taking off shutter from the frame) not exc 1.5sqm each complete all as specified and directed. |
| 14 | Taking down chowkats or frame with shutter (without taking off shutter from the frame) exc 1.5 Sq m but not exc 4.00 Sq m each complete all as specified and directed. |
| 15 | M&L for 35mm thick factory made Flush shutters, solid core construction, with block board core and plywood face panels, comercial type 1.0mm thick (veneered on both side) with decorative choice laminated type 1 (factory laminated), or surface finish, 6mm thick or external teak wood lipping fixed with nails, color and pattern as approved by EIC/GE complete all as specified and directed.. |
| 16 | S & F 35mm thick 2nd class Hard wood Glazed and Skelton shutters, open rebated and prepared to receive glass, gauze etc(without sash bars) edges of framing plain, chamfered or rounded, fitted with cut ,mitered andmoulded beads for securing glass etc, sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed. |
| 17 | S & F Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom andsideswithrequired EPDM rubber/ neoprene gasketetc.Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge complete all as specified and directed. |
| 18 | S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge complete all as specified and directed. |
| 19 | S&F 4.00mm thick sheet glass, selected ordinary quality and glazing with rubber beading or with glazing clips exc 0.5 sq. m in each pane including solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers, complete all as specified and directed. |
| 20 | S&F 4.00mm thick figuredglass, pin head typeand glazing with rubber beading or with glazing clips n exc 0.5, complete all as specified and directed. |
| 21 | S&Fstainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed. |
| 22 | S & F Mild steel bands, straps, supports or stays for rainwater, ventilating pipes, including bolt, if required hooks (stay), heavy for large gates, hook and pintle hinges, large hasps and staples, chains, hand made sliding bolts, clamps hold fasts, wall ties, hooks for hanging fans, plain angles cleats for securing purlins to wood trusses or rafters, knee piece inserts, two way and three way straps, plate washers and similar small articles conforming to Fe 310-O or Fe 410-O complete all as specified and directed. |
| 23 | M & L Cement concrete type B1, 1:2:4 (20 mm graded aggregate) as in coping, bed plate for hold fast including necessary formwork required etc complete all as specified and directed. |
| 24 | M&L for 100mm butt hinges of stainless steel grade 202, 14 gauge thickness, medium weight of approved make fixed with pressed steel door frame/Angle iron frame/PVC door frame with screw complete all as specified and directed. |
| 25 | M&L for 75mm butt hinges of stainless steel grade 202, 14 gauge thickness, medium weight of approved make fixed with pressed steel door frame/Angle iron frame/PVC/WPC door frame with screw complete all as specified and directed. |
| 26 | S & F200mm long Aluminium anodised barrel tower bolt of extruded section and fixed complete all as specified and directed. |
| 27 | S & F 150 mm size extruded aluminium alloy handles, fabricated type anodised complete all as specified and directed. |
| 28 | S & Faluminium anodisedHasp and staple, safety type of size 75 mm with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed. |
| 29 | S & F 250 mm aluminium alloy anodised sliding door bolts, with hasp and staple (bolt type) not less than 12mm dia with and and fixing clips of sheet cast or extruded section and fixing bolt and sliding bolt of extruded section or cast aluminium and fixed to wooden door shutters complete all as specified and directed. |
| 30 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 50 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made complete all as specified and directed. |
| 31 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-charge, complete all as specified and directed..(Note: stainless steel butt hinges and necessary SS screws shall be paid separately). |
| 32 | S&F in repair 18mm thick HDHMR BOARD exterior grade including any coloured prelaminated sheet of required thickness over HDHMR board, anti fungal, moisture resistance, anti borer as per IS 14587 for frame and shutter for kitchen cabinets/cupboards etc all as per specified and directed by Engr-in-charge. Note: sample as approved by GE. |
| 33 | S&F in repair 18mm thick HDHMR BOARD exterior grade including white coloured prelaminated sheet of required thickness over HDHMR board, anti fungal, moisture resistance, anti borer as per IS 14587 for frame and shutter for kitchencabinets/ cupboards etc all as per specified and directed by Engr-in-charge. Note: sample as approved by GE. |
| 34 | S & F 150mm aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and directed. |
| 35 | S&F floor door stopper of aluminium alloy body and tongue, overall length of cover plate 140mm anodised with hard drawn steel spring, fixed in floors complete all as specified and directed. |
| 36 | S&F magnet door stopper of rectangular size for PVC cabinets including all fittings fixed complete all as specified and directed. |
| 37 | S & F SS W Hinges SS 202 Grade steel RustResistance , for fixing cup boards shutters sizes of hinges 3\" to 4\" and 1.5 mm thickness, suitable for 18 mm thick cabinets shutters complete all as specified and directed |
| 38 | S&F 100 mm Pull door handles, chrome finish, Stainless steel of SS 304 grade all as per specified and directed by Engr-in-charge. Note: sample as approved by EIC/GE |
| 39 | S & F tubular curtain rails 25mm dia stainless steel 202 grade drapery type complete all as specified directed. |
| 40 | S & F in repairs stainless steel socket fancy type with bracket for 25mm dia stainless steel tubular curtain rod (design of socket shall be approved by GE/AGE at the time of execution) complete all as specified and directed.. |
| 41 | S & F in repairs 20mm dia brass chromium plated tubular towel rail complete all as specified and directed. |
| 42 | S & F for Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete confirming to grade Fe 410-W (Gde- E- 250) quality-A, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and directed. |
| 43 | M & L in repair forFramed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framedbalusters; walk ways; railings; framework (caging) of water tanksand similar work con- forming to Fe.290.Gde-E-165 complete all as specified and directed. |
| 44 | M & L for preparing newsteel surface of any description not otherwise described over 10cm width or girth and applyingtwo coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. |
| 45 | M & L for preparing newsteel surface of any description not otherwise described not exc. 10cm width or girth and applyingtwo coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. |
| 46 | M & L for preparing newwoodensurface of any description not otherwise described over 10cm width or girth and applyingtwo coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed. |
| 47 | Taking up or down 15mm bore steel tubing and connections, including removal out side MD land all as directed by Engr-in-Charge. |
| 48 | S&F20 mm outer dia CPVC pipes SDR 11 & plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed. |
| 49 | Taking up or down 20 mm bore steel tubing and connections, including removal out side MD land all as directed by Engr-in-Charge. |
| 50 | S&F 20mm bore galvanised mild steel tubing medium grade with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and directed. |
| 51 | Taking up or down 25mm bore steel tubing and connections, including removal out side MD land all as directed by Engr-in-Charge. |
| 52 | S & F 25mm bore galvanised mild steel tubing medium grade with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and directed. |
| 53 | S & F in repairs 110 mm borePVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall complete all as specified and directed. |
| 54 | S & F in repairs 110 mm borePVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed. |
| 55 | S & F in repairs 110 mm bore PVC (SWR) bends any radius all as specified and as directed. |
| 56 | S & F in repairs 110 mm bore PVC (SWR) bends any radius with oval access doors complete all as specified and directed. |
| 57 | S & F in repairs 75mm borePVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall all as specified and as directed. |
| 58 | S & F in repairs 75mm bore PVC (SWR) bends any radius all as specified and as directed. |
| 59 | S & F in repairs 75mm bore PVC (SWR) bends any radius with oval access doors all as specified and as directed. |
| 60 | S & F in repair 75mm PVC (SWR) floor trap, including jointing with solvent all as specified and as directed. |
| 61 | S&F in repairs grating 150mmx150mm made out of stainless steel complete all as specified and directed. |
| 62 | S & F in repairs 110mm bore PVC (SWR) branch piece, single (single Y) equal or unequal or with parallel branches with access door all as specified and as directed. |
| 63 | S & F in repairs 75mm bore PVC (SWR) branch piece, single (single Y) equal or unequal or with parallel branches with access door all as specified and as directed. |
| 64 | S & F stack clamps made out of 50mm x 5mm flat iron and 16mm dia round iron stays incliding bolts and nuts and securing ends of stays to walls and roofs for 110mm bore pipe all as specified and as directed. |
| 65 | S & F stack clampsmade out of 50mm x 5mm flat iron and 16mm dia round iron stays incliding bolts and nuts and securing ends of stays to walls and roofs for 75mm bore pipe all as specified and as directed. |
| 66 | S & F 110mm PVC (SWR) vent cowl all as specified and as directed. |
| 67 | S & F 75mm PVC (SWR) vent cowl all as specified and as directed. |
| 68 | S & F in repairs 15mm bore chromium plated fancy type bib tap long body, screwed down, high pressure for iron pipe or for brass ferrule complete all as specified and directed. |
| 69 | S & F CP wall mixer three in one system for mixing hot and cold water screwed down for iron pipe 15 mm bore and fixed complete all as specified and directed. |
| 70 | S & F in repairs stop valves/Angle valve15mm bore fancy type chromium plated screwed both ends for iron pipe or for unions and fixed complete all as specified and directed. |
| 71 | S & F in repairs 25mm dia bore gun-metal, globe or gate valves with iron wheel head screwed both ends for iron pipe and fixed complete all as specified and directed. |
| 72 | S & F in repairs 20mm dia bore gun-metal, globe or gate valves with iron wheel head screwed both ends for iron pipe and fixed complete all as specified and directed. |
| 73 | S & F in repairs 125mm dia chromium plated shower rose with swivel joints including fixing to steel pipe orGI union complete all as specified and directed. |
| 74 | S&F 32 mm bore low density polyethylene pipe (LDPE) of pressure rating 6 Kgf/cm2 as in waste pipe complete all as specified and directed. |
| 75 | Dismantling of water storage tank of 500 ltrs capacity complete all as specified and directed.. |
| 76 | S & F 1000 Ltrs Rotational moulded polyethylene water storage tanks triple layered (cylin-drical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I |
| 77 | S & F 25 mm bore in repairs Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/20 mm - 210 gms /25mm-455gms/ 40mm- 690 gms) complete all as specified and as directed. |
| 78 | S&F in repair Vitreous China wash down water closet pan (European pattern), white (excluding fixing bolts, flushing cistern and flush pipe) squatting pan including connection to trap, and to flushing pipe, anti-syphonage pipe, etc. complete including making good to floor. complete all as specified and as directed. |
| 79 | S&F in repairs Plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed. |
| 80 | S&F in repairs Vitreous China wash down water closet (Squat pattern ) white complete as fixed in repair excluding flushing cisternand flush type \"Orrisa\" pattern size 580x440 with integral footrest inject connection to trap antisyphonage etc complete including joint between flushing pipe and socket of WC. |
| 81 | S&F in repairs PVC flushing cistren low level, 10 ltr capacity with syphonic action type ball valve. Incl inlet ball valve, PVC band (flush pipe) 32mm complete all as specified. |
| 82 | S&F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified. |
| 83 | S & F 110mm PVC (SWR) WC connector with lip ring all as specified and as directed. |
| 84 | S & F 110mm PVC (SWR) WC connector bent type to fit WC outlet all as specified and as directed. |
| 85 | S & F 110mm PVC (SWR) junction single, (Single T, \"Y\" type) equal or unequal all as specified and as directed. |
| 86 | S & F 75mm PVC (SWR) junction single, (Single, \"Y\" type T) equal or unequal all as specified and as directed. |
| 87 | S&F in repair vitreous china Wash hand basin, white , flat back size 450x300 mm except taps, CP waste coupling but incl brackets all as specified. |
| 88 | S&F in repair brass CP centre hole basin mixer for mixing hot & cold water three way screwed down for iron pipe 15mm bore and fixed complete all as specified and directed. |
| 89 | S & F 32 mm dia stainless steel waste coupling for wash hand basin all as specified and directed. |
| 90 | S & F in repair PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed. |
| 91 | S&F in repairs 350x450mm size cabinet mirror rectangular shape with 4mm thickselected quality mirror and PTMT frame with openable door shutter with PTMT frame outside mirror as complete all as specified and directed. |
| 92 | S&F in repairs sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever bracket and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and directed. |
| 93 | Supply & Fix in repairs stainless steel wall mounted plate rack of size 880x880X 220 mm and thickness of sheet not less than 0.50mm with provn for keeping plates and other crockeryfixed with screw and rawal plug etc on wall complete all as specified and as directed |
| 94 | S& F in repair PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and as directed. |
| 95 | Demolition of reinforced cement concrete as in Roofs,floors(otherthan ground floors), beams, staircases, landing, chajjas and similar suspended work complete all as specified and directed. |
| 96 | M&L Cement concrete type B1 1:2:4 (20 mm graded aggregate) as in roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and directed. |
| 97 | Taking down cement plaster on brick/concrete surface including racking out joints hacking for key scrubbing down with water etc. complete all as specified and directed. |
| 98 | Demolition brickwork or stone/boulder masonry built in cement mortar including all quoins, arches, pillars, etc, complete all as specified and directed. |
| 99 | M&L Brickwork with sub class ‘B’ bricks straight or curved on plan exc 6 mmean radius built in CM 1:6 complete all as specified and directed. |
| 100 | S&F 40mm bore UPVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc., any type of pipe complete all as specified and directed. |
| 101 | M & L Rendering 10 mm thick onfair faces of brick work or concrete surfaces of wall in cement mortar 1:6 for finished even and smooth (without using extra cement) complete all as specified and directed. |
| 102 | M&L Rendering in two layer onfair faces of brick work or concrete sur-faces of wall 5 mm thick in CM 1:4 mixed with WPCas per manufacturers instructiion for finished even and smooth without using extra cement over 10 mm thick rendering incement mortar 1:6 (WPC will be measured and paid separately) complete all as specified and directed. |
| 103 | M&L Rendering 5 mm thick onfair faces of brick work or concrete sur-faces of ceiling in cement mortar 1:3 for finished even and smooth (without using extra cement) complete all as specified and directed. |
| 104 | M & L for preparingnew plastered surfaces of wall and applying two coats of oil bound distemper over and includinga coat of 2mm averagethickness birla/ equivalent wall care putty and one coat of primer complete all as specified and directed. |
| 105 | M & L for preparation of newplasteredsurfaces and applying three coats of white wash matching to existing of wall surface complete all as specified and directed.. |
| 106 | M& L for applying Twocoats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed. |
| 107 | M & L for preparing new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed. |
| 108 | M & L for complete removal of loose / cracked concrete incl reinforcement if required, from RCC roof projection,chajja,fins,facia, roof bands etc and making good with PCC (1:1 ½ :3) type A0 (using 12.5 mm graded stone aggregate) in any slab and in anyposition finished the surface even and smooth with out using extra cement including necessary form work and welding/binding of reinforcement (including reinforcement)if required complete and applying three coat of white wash/two coat of cement base paintto match with the existing surface as directed by the Engr- in -Charge. (Reiforcement will be measured and paid saperately under respective item complete all as specified and directed. |
| 109 | M&L for Providing precast cement concrete Type B1, 1:2:4 (using 20 mm Aggregate) as in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces including chamfers, weatherings, throat- ing etc. and setting in mortar complete with joints to match complete all as specified and directed. (reinforcement shall be measured and paid separately) |
| 110 | M&L for Providing reinforced cement concrete (nominal mix) Type B1, 1:2:4 (using 20 mm Aggregate) as inSlabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like including necessary form work complete all as specified and directed. Note. (reinforcement shall be measured and paid separately) |
| 111 | M & L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. |
| 112 | Complete removal of existing unservicable roof treatment incl taking down plaster, padding of any description and any position, cleaning, flushing out junctions of parapet wall washing down with water etc to prepare surface for new WPT including removing off rubbish at out side MD land. and complete all as specified and directed. |
| 113 | M&L for 50 mm avg thick PCC padding in cement concrete type B0 (1:2:4) using 12.5 mm graded stone aggr mixed with WPCas per manufacturer\"s instructions of cement finished surface even and fair without using extra cement for laying of WPT all as specified and directed. (WPC will be measured and paid separately). |
| 114 | M&L 10mm thick rendering on roof in CM 1:3 mixed with WPC as per manufacturer\"s instructions of cement for finished even and smooth without using extra cement over PCC surface forlaying APP membrane on roof(WPC will be measured and paid separately) complete all as specified and directed. |
| 115 | M&L for water Proofing treatment to roof slabs by applying one coat of bituminious/polymerized primer confirming to IS-3384 @ 0.40 Ltrs/Sqm, 3 mm thick APP modified polymeric membrane of weight of 3 kg/sqm with non-woven polyester reinforcement shall be laid over a coat of bitumen S-35 grade (30/40) applied @1.20Kg /Sqm (minimum) with minimum75 mm side overlaps and minimum 100 mm end overlaps, joints & overlaps shall be sealed by torch application and applying one coat of aluminium paint @ 0.11 Kg/Sqm over APP membrane complete all as specified and directed by Engr-In-Charge (Note: the primer and the membrane to be used shall be of the same manufacturer and to be applied by authorized applicator of OEM). |
| 116 | M & L for brushing with neat cement slurry @ 3Kg/Sqm complete all as specified and directed. |
| 117 | Supply only Internal water proofing compound (Liquid type) all as specified and directed. |
| 118 | Demolition of existing PCC/lean concrete including floor tiles and removing rubbish off the premises complete all as specified and directed. |
| 119 | M&L for 15 mmthick plaster in sunken portion with CM 1:3 mixed with liquid water proofing compound as per manufacturers instruction and should be finished even and smooth without using extra cement complete all as specified and directed.Note . (WPC will be measured and paid separately). |
| 120 | M&L for providing & laying applying one coat of bituminious/polymerized primer confirming to IS-3384 @ 0.40 Ltrs/Sqm, 3 mm thick APP modified polymeric membrane of weight of 3 kg/sqm with non-woven polyester reinforcement shall be laid over a coat of bitumen S-35 grade (30/40) applied @1.20Kg /Sqm (minimum) with minimum75 mm side overlaps and minimum 100 mm end overlaps, joints & overlaps shall be sealed as per manufacturer instructions complete all as specified and as directed. |
| 121 | M&L for sunken portionfilled with lean concrete 1:5:10 using brick/lime aggregate and finish the surfaces rough to receive sub base complete all as specified and as directed. |
| 122 | M & L for 25 mm thick cement concrete in flooring type BO, 1:2:4 (12.5mm graded aggregate) with liquid water proofing compound as per manufacturers instructions for laying floor tiles complete all as specified and directed. Note (WPC will be measured and paid separately). |
| 123 | Demolition of cement concrete of any description and in any position not otherwise specifically provided complete all as specified and directed.. |
| 124 | M & L for 75 mm thick PCC 1:3:6mix type C2 using 40mm graded stone aggregate as in paving finishing cone surface (plinth protection) even and smooth without using extra cement complete all as specified and directed.. |
| 125 | M&L 15 mm thick Damp proofcourse in cement mortar 1:2 to vertical surfaces including necessary formwork using water proofing compound @ 3% by wt of cement complete all as specified and directed.(WPC will be measured separately) |
| 126 | M&L Polythene film, 50 micron thick, laid on a coat of bitumen primer, @ 0.30 to 0.50 kg per sq. m complete all as specified and directed. |
| 127 | Supply only Integral waterproofing compound complete all as specified and directed. |
| 128 | M&L Treatment of surface under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and directed. |
| 129 | M&L Treating the soil under plinth protection at the rate of 5 litres of anti termite chemical emulsion Chloripyriphos (20EC) per square metre of surface area complete all as specified and directed. |
| 130 | M& L for complete removal ofoldexternal wall existing treatmeant complete by scrapping and or rubbing andapplying Twocoats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer to match the existing surface complete all as specified and directed. |
| 131 | M & L for complete removal of old existing treatment completely by scrapping and or rubbing of wall and applying two coats of oil bound distemper over a coat of 2mm averagethickness birla/ equivalent wall care putty and one coat of primer complete all as specified and as directed. |
| 132 | M & L for complete removal of old existing treatment completely by scrapping and or rubbing of ceiling and applying two coats of oil bound distemper over a coat of 2mm averagethickness birla/ equivalent wall care putty and one coat of primer complete all as specified and as directed. |
| 133 | M & L for preparing old plastered surfaces of ceiling and applying two coat of white wash on ceiling to match the existing surfaces complete all as specified and directed. |
| 134 | M & L for preparing old plastered surfaces of walls and applying two coat of white wash on ceiling to match the existing surfaces complete all as specified and directed.. |
| 135 | Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in Soft/loose soil, complete all as direced by Engr-in-Charge. |
| 136 | Removing excavated soil exc. 1.5km but not exc 5.0 km from the starting point and deposited outside of MD land complete all as specified and directed. |
| 137 | M&L Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified. |
| 138 | M&L Hard core gauge not exc. 63mm of broken bricks deposited spread and levelled in layers not exc. 15 cm watered and rammed to a true surface complete all as specified. |
| 139 | M & L for 75 mm thickcement concrete in sub base for path/paving flooring type D-2, 1:4:8 (40mm graded aggregate) for laying cement concrete tiles complete all as specified and directed. |
| 140 | M&L for 75 mmthick PCC 1:2:4 mix ,type B-2 Using 40 mm graded stone aggregate finished even and fair without using extra cement as in path/hard standing complete all as specified and directed. |
| 141 | M & L for Forming 65mm deep x 10mm thick contraction (dummy joints), filled with sealing compound grade \"A\" complete all as specified and directed. |
| 142 | Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, watering and removing surplus soil to a distance not exc 50m and making good surface complete all as specified and directed. |
| 143 | M & L for cement concrete 1:4:8 type D2 using 40mm graded stone aggregate as in boundry pillars and posts footing etc complete all as specified and directed. |
| 144 | M & L for mild steel work confirming to Fe-290 Gde E-165 in angle iron posts & struts in fencing and in parking sheds including cutting top to shape as directed, drilling holes, notching for wire, etc. and including flat iron filletes for securing wire mesh or fence etc. including allnecessary bolting riveting etc complete all as specified and directed. |
| 145 | S & F pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa, AZ150 as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 146 | M & L for preparation of newplasteredsurfaces and applying two coats of cement base paint over a coat of primer all as specified and directed. |
| 147 | M & L for 75 mm thick PCC 1:4:8mix type C2 using 40mm graded stone aggregate as in paving finishing cone surface (plinth protection) even and smooth without using extra cement complete all as specified and directed. |
| 148 | M&L for 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed. |
| 149 | M & L for Filleting in any position and to any shape n. exc. 25 sq. cm in cement mortar 1:4 including all mitres, stops, etc. complete all as specified and directed. |
| 150 | Supply and laying in trenches of GI steel tubing medium grade including all fittings such as Tees, elbow,bends etc for 50mm bore of pipe complete all as specified. |
| 151 | Supply and laying in trenches of GI steel tubing medium grade including all fittings such as Tees, elbow,bends etc for 25mm bore of pipe complete all as specified. |
| 152 | Supply and laying in trenches of GI steel tubing medium grade including all fittings such as Tees, elbow,bends etc for 20mm bore of pipe complete all as specified. |
| 153 | S & F 25mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe complete all as specified and directed. |
| 154 | M& L for cutting existing steel tubing for alteration or additions (Each cut measured) and inserting newTee, bend, elbowetc up to 50mm dia complete all as specified and directed. |
| 155 | S & F 50mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe complete all as specified and directed. |
| 156 | S & F 20mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe complete all as specified and directed. |
| 157 | Excavation in trenches not exc 1.5 mtr in depth for taking out cable / pipe line not exc. 10sq mtr on plan and notexc 1.5 mtr depth and getting out in soft/loose soil complete all as specified and directed. |
| 158 | Returning filling in trenches excavatied soil including spreading levelling watering and well ramming in lasyers not exc 25 cm complete all as specified and directed. |
| 159 | Removing excavated materials not exc 50 mtr depositing where directed at a level not exc 1.5m above the strating point complete all as specified and directed. |
| 160 | Taking down copper/aluminium point wiring (light fan, socket or power) complete including fittings such as switch, sockets, c/rose, lamp holders, tube light fittings, sketch fittings, wooden boards, bell push, cat bell, MCBs & regulator etc & makinggood to distrubuted surfaces & matching with the existing colour of wall floor etc complete all as specified and directed. |
| 161 | Taking down main switch, DB/change over/ VTPN, MCCb AC box of any capacity complete all as specified and directed. |
| 162 | M&L for concealed point writing with 1.5 Sqmm PVC-FRLS insulated, sheathed, copperv conductor, stranded 1100 volt grade cable in incl PVC conduit, including modular metal flush boxes & modular white cover plate with frame as per siterequirement all fittings such as tees, bends, elbow, etc. of External diameter 20 mm all as per site requirements PVCinsulated & sheathed 1100 volt grade copper conductor, stranded 1.5sqmm cable as cotinuous earth lead complete all as specified and colour coding of cables such as Phase- Red, Neutral- Black, and Earth- Green all as directed by Engg-in-charge. incl cutting and chasing in stone/brick masonry and matching with existing suface complete all as specified and directed.For one light, fan point controlled by one switch |
| 163 | For one call bell point controlled by one push button switch |
| 164 | For one 5 Amp independent socket point controlled by one switch |
| 165 | For one 3 pin, 5 Amp socket point with other switch on the same board |
| 166 | For one light, point controlled by two way switch |
| 167 | All as per item No 162.00 here in before but for power point wiring using with 2.5 sqmm PVC-FR LS insulated, copper conductor stranded 1100 volt grade cable and 2.5 sqmm PVC insulated sheathed, copper conductor stranded 1100 volt grade cable as continuous earth lead complete all as specified and directed by Engineer-in-charge |
| 168 | S& F Modular switch, one way, 6 Amp 230, 1 module complete all as specified and directed. |
| 169 | S& F Modular switch, two way, 6 Amp 230, 1 module complete all as specified and directed. |
| 170 | S& F socket Modular 6 Amp-2/3 pin combined 2 module complete all as specified and directed. |
| 171 | S&F switch Modular, single pole, one way, 16 Amp, 1 module 230 Volt complete all as specified and directed. |
| 172 | S & F socket modular 6/16 Amp, 2/3 pin combined, 2 module 230 Volt complete all as specified and directed. |
| 173 | S&F ceiling rose, surface backlit, three terminal complete all as specified and directed. |
| 174 | S&F Modular lamp holder Polycarbonate type with back plate suitable for Batten fitting Suitable for B22 type bulb complete all as specified and directed. |
| 175 | S&F modular fan step regulator 120W 2 module complete all as specified and directed. |
| 176 | S&F modular bell push 6A, 1 module complete all as specified and directed. |
| 177 | S&F call bell ding dong 230 Volt, single phase complete all as specified and directed. |
| 178 | Supply and fixing LED lights fitting made of Aluminium extrusion 1x 20W (4 feet), input voltage 140-270 V AC,CCT 6500K,Lumin efficency 100 lm/wall, surge protection upto 4KV, Voltage protection upto 440 v AC PF>0.9, connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as directed by Engg-in- Charge.Note : Warrenty on light should be of minimum 02 years. |
| 179 | Supply and fixing LED lights fitting made of Aluminium extrusion mirror type with high out put diffuser 1x10 watt (4 fet), input voltage 140-270 v AC,CCT 6500K, Lumin efficiency 100lm/watt, surge protection upto 4KV, Voltage protection upto 440 V AC.PF >0.9 with driver including connecting up with flexible copper conductor cable of suitable size complete all as specified and directed by Engineer-in-charge. Note: Warrenty on light should be of minimum 02 years. |
| 180 | S&F LED light fitting 1x15 Wbulkhead luminaries Pressure die cast aluminium housing crystal white lumens 100lm/watt IP-65 including LED lioght driver holder connecting up with three core flixible copper conductor cable of suitable size complete all as specified and directed by Engineer-in-charge.Note: Warrenty on light should be of minimum 02 years. |
| 181 | S&F LED bulb B22 9 watt inverter bulb, lumin efficiency 900 lumin/watt in normal mode and 350 lumin/watt in power backup mode,CRI >80, CCT-6500K, surge protection upto 4KV, Voltage Protection upto 400 volt, PF >0.9 suitable for batten holder fitting complete all as specified and directed by Engr in charge.Note: Warrenty on light should be of minimum 02 years. |
| 182 | S & F BLDC White colour ceiling fan complete with blades and antisuside rod from existing roof/trus to fall ceiling, and accessories, 230V,1200mm sweep. Min air delivery 210 CFM with service value 6.00 BEE, Winding material 100% copper 350 RPM air velocity 215m3/min, anti rust blades five star rated with brushless direct current motor including ceiling fan connecting up with three core flexible copper conductor cable of suitable size from ceiling rose and taking downexisting UNSV ceiling fan complete all as specified and directed.Note: 1) Old ceiling fans shall be deposited to AGE E/M store yard for re issue to other buildings after repair/servicing or suryed off as per procedure in vogue etc.2) 02 years gurantee to be provided by the contractor. |
| 183 | Taking down and refixing connecting same electric meter SP up to 60 amp incl S & F suitable new board close recessed, type of suitable size and making good distrubed surface and matching with the existing colour of wall, a as specified and directed by Engineer-in-charge. |
| 184 | M&L electric water heater (geyser) 25 Ltrs capacity AC 230V, 5 star rating Branded heavy duty automatic cutoff and including electric connection lead and water connection of both power consumption 2000watt of suitable size and length and all accessories, grouting of nut bolt/fasners on wall and making good distrubed surface complete all as specified and directed. |
| 185 | S&F of exhaust fan made of sturdy engineering steel body complete net mosquito with louvers shutter, voltage 230V, 50Hz, RPM 1400, 70 watt, noise level 40-45db area dynamically designed & balanced blade, 4 nos blade, Air flow capacity 1850m3/hrCMPH< copper winding of sweep 300mm including exaust fan connecting up with three core flexible coper conductor cable of suitable size from ceiling rose and taking down existing UNSV exaust fan complete all as specified and directed.Note: 1) Old unserviceable Exhaust fans shall be depoisted to AGE E/M store yard for re-issue to other buildings after repair/servicing or suryed off as per procedure in vogue etc. complete all as specified and directed.2) Making suitable size of hole on wall for fixing the exhaust fan 3. 02 years gurantee to be provided by the contractor. |
| 186 | S&F of exaust fan of white colour made of study engineeringPVC complete with louvers shutter, voltage 230V, 50Hz, RPM 1200, noise level 40-45 db, water resistant,copper winding of sweep 250mm including exaust fan connecting up with three core flxible copper conductor cable of suitable size from ceiling rose and taking down existing UNSV exaust fan complete all as specified and directed.Note:1) Old unserviceable Exhaust fans shall be depoisted to AGE E/M store yard for re-issue to other buildings after repair/servicing or suryed off as per procedure in vogue etc. complete all as specified and directed.2) Making suitable size of hole on wall for fixing the exhaust fan 3. 02 years gurantee to be provided by the contractor. |
| 187 | M&L concealed sub main wiring with two single core PVC FRLS insulated unsheathed stranded copper conductor cable FRLS, 02 runs of 01 Single core of size 6 sqmm(for main current) drawn in &incl PVC conduit not less than 25mm dia ISI marked with all accessories such as tee,bend .joint cover etcround/square blocks at junction etc,all as per site requirements ISI marked with one run of 01 Single core of size 6 Sqmm (as earth wire) PVC insulated unsheathed stranded copper conductor as a continous earth wire complete all as specified incl. taking down old unservicable sub main wiringand colour coding of cables such as phase- Red, Netural- Black, and Earth- Green complete all as directed by Enggineer in charge Note : One length of PVC Conduit and 3 run of cable shall be measured and paid as one length. |
| 188 | S&F testing and commissioning of MCB SP 5 Amp to 32 Amp 240 Volt 10 KV capacity having C-curve characterstics connected with suitable lugs complete all as specified and directed. |
| 189 | S&F testing and commissioning of MCB SPN 32 to 40 Amps, 240 Volt 10 KV capacity having C-curve characterstics connected with suitable lugs complete all as specified and directed. |
| 190 | S&F sheet metal enclosure DB double door, IP-43 when MCBs to be used SPN, 12 WAY, 240V with 200 Amps rated bus bar of suitable size complete all as specified and directed. |
| 191 | S&F double door metallic sheet metal enclosure VTPN DB with provision for housing 63 Amp MCCB as incomer 4 way with 200 AMPS rated bus bar. |
| 192 | S&F MCCB 63 Amps 4 Poles, suitable for 415V breaking capacity 16KA connected in wall/surface with wire and lugs all as specififed and directed. |
| 193 | S&F of LED street light fitting 35 Watt 230V AC CCT 5700K Lumens ≥ 100lm/watt outdoor type with high pressure die cast Aluminium housing high power led as lighting source and lens embedded PC cover having top opening separate driver compantment and impact resistance of IK 07 WITH 10KV, OEM driver, PF 0.9, built in surge protection device heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection, including bracket made out of GI pipe light grade 32mm bore not less than 1.20 long bent to shape required fixed to pole with suitable size 2 Nos clamps made out of 25X3mm flat iron nut, bolts and washers complete all as specified and directed.Note : The warranty on light should be minimum of 2 Years. |
| 194 | NOTE : SCHEDULE OF CREDIT (Amount on page No 57 and 58 shall be deducted offline from the total quoted amount to arrive at the net contract sum to be considered for acceptance.) |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2025 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
