Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth, 1.5m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth, lead up to 50m and lift up to 1.5m,as directed by Engineer-in-Charge., All kinds of soilDSR 2023- 2.6.1 |
| 2 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :, 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources).DSR 2023- 4.1.8 |
| 3 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation leveling & dressing & finishing the top smooth.DSR 2023- 4.17 |
| 4 | Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 12.5mm nominal size derived from natural sources).DSR 2023- 4.10 |
| 5 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete., Fixed to steel windows by weldingDSR 2023- 9.48.1 |
| 6 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete., Hot finished welded type tubes.DSR 2023- 10.16.1 |
| 7 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement, All works upto plinth level, Concrete of M25 grade with minimum cement content of 330 kg /cumDSR 2023- 5.33.1.1 |
| 8 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement, All works above plinth level upto floor V level, Concrete of M25 grade with minimum cement content of 330 kg /cumDSR 2023- 5.33.2.1 |
| 9 | Mild steel or iron work in plain work such as in R.C.C. or R.B. (when not included in an over all rates ) including bending for proper completion of the work and including supply of steel and its wastage , bends, hooks and authorised overlaps shall be measured up to floor two level. (SI No. 504) (Sanction Rate)- SI 504 |
| 10 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:, Cement mortar 1:4 (1 cement : 4 coarse sand)DSR 2023- 6.1.1 |
| 11 | Brick work with common burnt clay machine moulded perforated bricks of class designation 12.5 conforming to IS: 2222 in superstructure above plinth level up to floor five level in cement mortar 1:6 (1 cement : 6 coarse sand) :, Brick work with common burnt clay machine moulded perforated bricks of class designation 12.5 conforming to IS: 2222 in superstructure above plinth level up to floor five level in cement mortar 1:4 (1cement: 4 Coarse sand): With F.P.S.(non modular) bricks.DSR 2023- 6.3.1 |
| 12 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level., Cement mortar 1:3 (1 cement :3 coarse sand)DSR 2023- 6.13.1 |
| 13 | Brick edging 7cm wide 11.4 cm deep to plinth protection with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 including grouting with cement mortar 1:4 (1 cement : 4 fine sand).DSR 2023- 6.44 |
| 14 | 12 mm cement plaster of mix :, 1:4 (1 cement: 4 fine sand)DSR 2023- 13.1.1 |
| 15 | 6 mm cement plaster of mix :, 1:3 (1 cement: 3 fine sand)DSR 2023- 13.16.1 |
| 16 | 20 mm cement plaster of mix :, 1:4 (1 cement: 4 fine sand)DSR 2023- 13.3.1 |
| 17 | Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.DSR 2023- 13.26 |
| 18 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade:, New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm)DSR 2023- 13.47.1 |
| 19 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08%and conforming to IS : 15622 , of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete., Size of Tile 600x600 mmDSR 2023- 11.41.2 |
| 20 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm(thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement :4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigment etc.,., complete.DSR 2023- 11.37 |
| 21 | Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge:, Profile B, Fixing with carbon steel galvanised dash fastener of required dia and size (to be paid for separately).DSR 2023- 10.14.1.2 |
| 22 | Providing and fixing glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes (weight not less than 10 kg per sqm) fixing with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws., Kiln seasoned and chemically treated hollock wood, 35 mm thickDSR 2023- 9.9.2.1 |
| 23 | Extra for Providing and fixing flush doors with decorative veneering instead of non decorative ISI marked flush door shutters conforming to IS: 2202 (Part I), On one side only.DSR 2023- 9.22.1 |
| 24 | Providing and fixing factory made uPVC glazed/wire mesh windows/doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod pf approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge. Wire mesh / Glazing of plain/ toughened/ laminated/ double glass unit with / without high performance coatings as per design requirements and conforming to IS: 3548 & IS:16231 shall be paid separately. Note:- Structural design proof checked from a Government Engineering Institute, to be provided by the manufacturer for: (i) Sites with basic wind speed > 45 m/sec as per IS 875 - Part 3 (ii) Sites with structure height more than 20m for all wind speeds., Two track two panels sliding window with Aluminium channel for roller track, wool pile, nylon rollers with SS 304 body., Two track four panels sliding windows with Aluminium channel for roller track, wool pile, zinc alloy (zamak) powder coated handle on three panels along with multi-point locking system, nylon rollers with SS 304 body., Two and half track three panels sliding window with two glazed & one wire mesh panels with Aluminium channel for roller track, wool pile, nylon rollers with SS 304 body., Three track three panels sliding window with two glazed & one wire mesh panels with Aluminium channel for roller track, wool pile, nylon rollers with SS 304 body., Using R2 series with frame (70mm & above) x (40mm & above) & both glazed and fly screen sash (25mm & above) x (50mm & above) with zinc alloy (zamak) powder coated touch locks with hook. (Height upto 1.2 meter).DSR 2023- 9.147.A4.1 |
| 25 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approvedmake, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.DSR 2023- 8.31 |
| 26 | Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigments etc., complete.DSR 2023- 11.40 |
| 27 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade:, Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade: Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture.DSR 2023- 13.62.1 |
| 28 | Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc. to be paid separately).DSR 2023- 21.18 |
| 29 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge.DSR 2023- 17.16A |
| 30 | Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge.DSR 2023- 17.22A |
| 31 | Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm or 340x410x265 mm sizes respectively.DSR 2023- 17.23 |
| 32 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:, White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar tapsDSR 2023- 17.7.1 |
| 33 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete., Flexible pipe, 32 mm diaDSR 2023- 17.28.2.1 |
| 34 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:, White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tapDSR 2023- 17.7.2 |
| 35 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:, White Vitreous China Angle back wash basin size 600 x 480 mm with single 15mm C.P. brass pillar tapDSR 2023- 17.7.5 |
| 36 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings andfixtures complete, including cutting and making good the walls and floors wherever required :, W.C. pan with ISI marked white solid plastic seat and lidDSR 2023- 17.2.1 |
| 37 | Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour., 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms.DSR 2023- 17.73.1 |
| 38 | Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms., 15 mm nominal bore.DSR 2023- 18.50.1 |
| 39 | Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms., 15 mm nominal boreDSR 2023- 18.51.1 |
| 40 | Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931., 15 mm nominal bore.DSR 2023- 18.52.1 |
| 41 | Providing and fixing PTMT soap Dish Holder having length of 138 mm, breadth 102 mm, height of 75 mm with concealed fitting arrangements. Weighing not less than 106 gms.DSR 2023- 18.65 |
| 42 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes., 110 mm diameterDSR 2023- 12.41.2 |
| 43 | Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion., Coupler, 110mmDSR 2023- 12.42.1.2 |
| 44 | Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion., Single pushfit Coupler :, 110mmDSR 2023- 12.42.2.2 |
| 45 | Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion., Single tee with door, 110x110x110 mmDSR 2023- 12.42.3.2 |
| 46 | Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion., Bend 87.5°, 110 mm bendDSR 2023- 12.42.5.2 |
| 47 | Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion., Shoe (Plain), 110 mm ShoeDSR 2023- 12.42.6.2 |
| 48 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete., 110 mmDSR 2023- 12.43.2 |
| 49 | 15 mm cement plaster on the rough side of single or half brick wall of mix :, 1:4 (1 cement: 4 fine sand)DSR 2023- 13.2.1 |
| 50 | Wiring Points in Surface Conduit with PVC insulated 1100 V grade cable, Wiring point for light with 1.5 sq. mm.FRLSH PVC insulated multistrand single core copper conductor cable in heavy guage rigid steel conduit pipe on surface, complete with 14 SWG copper earth continuity wire,GP Box ,piano type switch and ceiling rose/angle/ batten holder on 3 mm. thick phenolic laminated backelite sheet etc. complete in all respect, as directed .SOR 2018 (E-M)- 1.1.121(B) |
| 51 | Wiring Points in Surface Conduit with PVC insulated 1100 V grade cable, Wiring point for fan /fresh air fan (light duty exhaust fan) with 1.5 sq.mm.FRLSH PVC insulated multistrand single core copper conductor cable in heavy guage rigid steel conduit pipe on surface complete with 14 SWG copper earth continuity wire, piano type switch & ceiling rose on 3 mm. thick phenolic laminated backelite sheet etc, complete in all respect.SOR 2018 (E-M)- 1.1.123 (B) |
| 52 | Wiring Points in Surface Conduit with PVC insulated 1100 V grade cable, Wiring point for exhaust fan with 1.5 sq. mm.FRLSH PVC insulated multistrand single core copper conductor cable in heavy guage rigid steel conduit pipe on surface complete with14 SWG copper earth continuity wire, 15 A piano type switch & ceiling rose on 3 mm.thick phenolic laminated backelite sheet etc, complete in all respect.SOR 2018 (E-M)- 1.1.127(B) |
| 53 | Wiring Points in Conduit Partly Laid in slab and partly Concealed in Wall, Wiring point for two ways light with 1.5 sq. mm. F.R. PVC insulated multistrand single core copper conductor cable in heavy guage rigid steel conduit pipe partly concealed in the wall and partly laid in slab alongwith the reinforcement before concreting, complete with 14 SWG copper earth continuity wire , GP Box and two number two way piano type switches & ceiling rose / angle / batten holder on 3 mm thick phanolic laminated backelite sheet etc., complete in all respect, as directed, including matching colour wash.SOR 2018 (E-M)- 1.3.139 (B) |
| 54 | Wiring Points in Conduit Partly Laid in slab and partly Concealed in Wall, Wiring point for plug with 1.5 sq. mm.FRLSH PVC insulated multistrand single core copper conductor cable in heavy guage rigid steel conduit partly concealed in wall and partly laid in slab alongwith the reinforcement before concreting, complete with14 SWG copper earth continuity wire and piano type switch and socket etc., complete in all respect including matching colour wash.SOR 2018 (E-M)- 1.3.141 (B) |
| 55 | Wiring Points in Conduit Partly Laid in slab and partly Concealed in Wall, Wiring point for call bell with 1.5 sq. mm.FRLSH PVC insulated multistrand single core copper conductor cable in heavy guage rigid steel conduit partly concealed in wall and partly laid in slab alongwith the reinforcement before concreting complete with 14 SWG copper earth continuity wire GP Box and piano type bell push or 2 pin socket etc, complete in all respect including matching colour wash.SOR 2018 (E-M)- 1.3.142 (B) |
| 56 | Laying of conduit pipes in wall for total concealed light fan, plug points and for concealed sub mains, Same as in item 148 (A) but 25 mm dia 2 mm thick PVC conduit.SOR 2018 (E-M)- 1.4 (B).149(A) |
| 57 | Laying of conduit pipes in wall for total concealed light fan, plug points and for concealed sub mains, Same as in item 154, but for 25 mm dia 16 guage (1.5 mm) thick rigid steel conduit.SOR 2018 (E-M)- 1.4 (B).155 |
| 58 | G.P. Switch Boxes, Supply and fixing of switch box 100 x 100 x 50 mm size of approved make made up of 1.0 mm thick ISI Marked G.P.sheet All 4 corners folded & spot welded for screw and holes plugged with PVC Nylon Caps . Two or more holes for pipe entry of 25.4 mm on upper and lower sides of the box. Holes shuld be semi-shuttered type and fitted with heavy brass Earth Piller duly screwed & brand name should be embossed. Box flushed in wall including cutting of brick work, fixing it to the level with cement sand mortar, including matching colour wash with s/o all materials, labour and T&P required for proper completion of work as directed at site by the Engineer in charge.SOR 2018 (E-M)- 1.4 (C).159 |
| 59 | G.P. Switch Boxes, Same as in item No 159 but of but size 200 x 250 x 65 mm sizeSOR 2018 (E-M)- 1.4 (C).162 |
| 60 | G.P. Switch Boxes, Same as in item No 159 but of but size 250 x 250 x 65 mm sizeSOR 2018 (E-M)- 1.4 (C).163 |
| 61 | Concealed points using Existing Concealed Conduit and M.S. Boxes for Switch Boards, Wiring point for light in 1.5 sq. mm.FRLSH PVC insulated multistrand single core copper conductor cable (drawn through existing concealed steel conduit) and 5 Amp.flush type switch & ceiling rose/angle/batten holder fixed with 3mm thick phenolic laminated backalite sheet with brass machine screws and cup washers mounted over existing M.S. switch board box/ junction box with supply of all material, labour & T&P etc. required for proper completion of the work as directed at site by the Engineer in charge.SOR 2018 (E-M)- 1.4(D).174(B) |
| 62 | Concealed points using Existing Concealed Conduit and M.S. Boxes for Switch Boards, Same as in item no.174 (B) but for ceiling fan.SOR 2018 (E-M)- 1.4(D).177(B) |
| 63 | Concealed points using Existing Concealed Conduit and M.S. Boxes for Switch Boards, Same as in item 174(B) but for plug point with 5 Amp flush type switch and 3 pin socket and earth continuity wire of 1.5 sq.mm. FRLSH PVC insulated multi strand copper conductor cable.SOR 2018 (E-M)- 1.4(D).178(B) |
| 64 | Submain in conduit on surface( 2 wire 1100 V Grade), Supply and wiring of submain with two number 4 sq.mm. FRLSH PVC insulated 1100 V grade multistrand single core copper conductor cable in 20 mm dia heavy guage rigid steel conduit on surface, with one number 14 SWG copper earth continuity wire, complete in all respect.SOR 2018 (E-M)- 2.1.211(B) |
| 65 | Submain in conduit on surface( 2 wire 1100 V Grade), As in item no. 211 (B) but in 20mm dia heavy duty (2mm thick) PVC conduit with one number 2.5 sq. mm. multistrand copper conductor cable as earth continuity wire drawn in conduit.SOR 2018 (E-M)- 2.1.211(C) |
| 66 | G.I OCTAGONAL POLE Supply & fixing of 8 mtr GI Octagonal Pole of approved make (top dia 70mm, Bottom dia 135 mm and base plate 12mm thik) having 3mm thikness with Double arm bracket (1 Mtr length) on RCC foundation including the cost of foundation, founSOR 2018 (E-M)- 6.644 |
| 67 | Supply and burying of 40mm dia x 4.5 metres long G.I. Pipe vertically for earthing having 12mm dia. Holes spaced 75mm apart drilled up to 2 metre from the bottom complete with earthing lead of No. 6 to 8SWG GI wire in G.I. Pipe up to appron (and from appron to switch board the cost of G.I. wire and pipe will be extra) upto switch board, 30cm square C.I. box with hinged cover masonary enclosure, funnel at top, alternate layers of charcoal/coke and salt at least 150mm thick alround etc. as per directions of Engineer-in-charge complete in all respects as per drawing.SOR 2018 (E-M)- 7.701 |
| 68 | S&F of 40 Amp. D.P. Isolator, CAT ASOR 2018 (E-M)- 10.1005 (A).a |
| 69 | S&F of 40 Amp. TP MCB (10 KA) C Curve, CAT ASOR 2018 (E-M)- 10.1016.a |
| 70 | S&F of 6 Amp. to 32 Amp. TP MCB (10 KA) C Curve, CAT ASOR 2018 (E-M)- 10.1013.a |
| 71 | S & F surface/Flush mounting 4ways V TPN distribution board with additional metal door without MCB complete in all respect,as directed at site by Engineer in charge., CAT ASOR 2018 (E-M)- 10.1026 (C).a |
| 72 | Supply and fixing of call bell of approved make on polished MDFEG/ Teak ply board including making connections etc. complete in all respect.SOR 2018 (E-M)- 11.1101 |
| 73 | Supply and fixing of M.S. box of size 600mm x 480mm x 200mm deep in sunk for housing BDB/TPN fabricated from 16 gauge M.S. Sheet and 13mm x 2.5mm flat iron etc. painted outside with red oxide primer and inside with synthetic enamel paint complete in all rSOR 2018 (E-M)- 11.1114 B |
| 74 | Erection and testing of ceiling fan and regulator etc. excluding supply of down rod, complete in all respect.SOR 2018 (E-M)- 11.1115 |
| 75 | Supply and fixing of fan hook fabricated from M.S. rod for ceiling fan each.SOR 2018 (E-M)- 11.1123 |
| 76 | Supply and fixing of cross clamp of required size fabricated from 50mm x 12mm M.S. flat complete with fan hook including painting etc. complete in all respect.SOR 2018 (E-M)- 11.1124 |
| 77 | Supply and fixing of heavy duty cadmium plated copper connector with end plate complete in all respect., Supply and fixing of fire extinguisher, ABC Type 4.00 kg. capacity (ISI Marked IS : 15683 & TAC approved) complete with initial charge and wall bracket, along with supply of all materials and labour for proper completion of work.SOR 2018 (E-M)- 11.11.1131 |
| 78 | Supply and fixing of power plug with 15A/250 volt flush type switch and 5 pin 15A/250V flush type universal socket in suitable M.S. box of 175mm x 100mm x 50mm size with phenolic laminated bakelite sheet cover 3mm thick fixed with brass machine screw andSOR 2018 (E-M)- 11.1139 |
| 79 | Supply and fixing of electronic fan regulator 120-280 V. ISI marked, on the existing switch board including making connections, required material, labour T&P etc. for proper completion of work to the satisfaction of Engineer in charge of work.SOR 2018 (E-M)- 12.1203 (A) |
| 80 | DOWN LIGHT LUMINAIRES Supply and fixing of recess/ Surface/ Pendent mounting round 10 to 15 Watt LED Down Lighter having Powder coated die cast aluminium housing with heat sink, diffuser/ Reflector and driver set complete in all respect., CAT-AASOR 2018 (E-M)- 14.1402.b |
| 81 | STREET LIGHT LUMINAIRES Supply and fixing of LED Street light Fitting having die cast aluminium body and diffuser with driver set suitable for 45 watt to 50 Watt. Confirming to IP 66 protection complete in all respect., CAT- AAASOR 2018 (E-M)- 14.1421.a |
| 82 | Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit along with 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.DSR 2022 E-M- 1.5 |
| 83 | Wiring for light/ power plug with 4X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit along with 2 Nos. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.DSR 2022 E-M- 1.6 |
| 84 | SAMSUNG/LG LED-TV-42\" (FULL HD)- TV-43\" |
| 85 | AIR CONDITIONERS WITH INVERTER TECHNOLOGY (5star)- AC-1.5T (1504) |
| 86 | LG Refrigerator 3-Star, Frost free smart Inverter- LG Refrigerator 3-Star |
| 87 | CEILING FANS Supply of Ceiling Fans with fan motor of A.C Permanent insulation, capacitor rating conforming BEE 5 Star rating and IS:374/79 and also comply with IS:1709/1984 with latest amendment. The rated voltage 220/240 volts, 50Hz, 1-ph AC. The fan assembly should consist of down rod blades, shackle canopies etc and with double ball bearing system., BEE 5 Star rated - 1200mm sweepSOR 2018 (E-M)- 15.1501.(i) |
| 88 | Wall Mountain Fan- Wall Mountain Fan (400mm swing/Havells or Crompton Make) |
| 89 | Exhaust fan 300mm- Exhaust fan 250mm make Havells or Crompton Make) |
| 90 | Dahua NVR 32 channel 4K 2Sata smart 8MP CP/Dahua/Bosh/Honey well- CCTV-1 |
| 91 | 4MP IR Bullet camera/Vary focal 2.8-12nm CP/Dahua/Bosh Honeywell- CCTV-2 |
| 92 | 2MP PT2 camera 100 mtr Range, 1R- CCTV-3 |
| 93 | Storage 4TB HDD WD/Segate- CCTV-4 |
| 94 | Network switch POE8 Port gigabit Dahua/CP- CCTV-5 |
| 95 | CAT6 wise STP 305 Meter outdoor double jacket- CCTV-6 |
| 96 | P2P wireless lensed/resius with all item- CCTV-7 |
| 97 | Pipe PVC with Laying/meter- CCTV-8 |
| 98 | Rack 4U Network- CCTV-9 |
| 99 | Installation Charge- CCTV-10 |
| 100 | Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessaryaccessories and screws etc. complete.DSR 2023- 9.84 |
| 101 | Providing and fixing chromium plated brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.DSR 2023- 9.88 |
| 102 | Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete :, 250x10 mmDSR 2023- 9.97.2 |
| 103 | Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete :, 150x10 mmDSR 2023- 9.97.4 |
| 104 | Providing and fixing aluminium handles ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete :, Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :125 mmDSR 2023- 9.100.1 |
| 105 | Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete., Twin rubber stopperDSR 2023- 9.101.2 |
| 106 | construction of granular sub base by providing close graded material , spreading in uniform layers with motor grader on prepared surface . mixing by mix in place method with front and loader at OMC ,and compacting with vibratory roller to achieve the desired density , complete as per clause 401- MOR 401/4.01 (B) |
| 107 | Providing and laying 60mm thick factory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge.DSR 2023- 16.68 |
| 108 | Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).DSR 2023- 16.69 |
| 109 | Supplying at site Angle iron post & strut of required size including bottom to be split and bent at right angle in opposite direction for 10 cm length and drilling holes upto 10 mm dia. etc. complete.DSR 2023- 16.19 |
| 110 | Fencing with angle iron post placed at required distance embedded in cement concrete blocks, every 15th post, last but one end post and corner post shall be strutted on both sides and end post on one side only and provided with horizontal lines and two diagonals interwoven with horizontal wires, of barbed wire weighing 9.38 kg per 100 m (minimum), between the two posts fitted and fixed with G.I. staples, turn buckles etc. complete. (Cost of posts, struts, earth work and concrete work to be paid for separately). Payment to be made per metre cost of total length of barbed wire used., With G.I. barbed wireDSR 2023- 16.18.1 |
| 111 | Surface dressing of the ground including removing vegetation and in- equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m. All kinds of soilDSR - 2020 (Horticulture)- 2.28.1 |
| 112 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. :Concealed work, including cutting chases and making good the walls etc., 15 mm nominal outer dia .Pipes.DSR 2023- 18.8.1 |
| 113 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. :Concealed work, including cutting chases and making good the walls etc., 25 mm nominal outer dia .Pipes.DSR 2023- 18.8.3 |
| 114 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge : External work, 25 mm nominal outer dia. Pipes.DSR 2023- 18.9.3 |
| 115 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge : External work, 40 mm nominal outer dia. Pipes.DSR 2023- 18.9.5 |
| 116 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge : External work, 15 mm nominal outer dia. Pipes.DSR 2023- 18.9.1 |
| 117 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.DSR 2023- 18.48 |
| 118 | Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinalpartitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finishedsmooth., Granite Stone of approved shadeDSR 2023- 8.10.2 |
| 119 | Providing and fixing uplasticised PVC connection pipe with brass unions :, 45 cm length, 15 mm nominal boreDSR 2023- 18.21.2.1 |
| 120 | Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design :, In 75x75 mm deep chaseDSR 2023- 12.21.1 |
| 121 | Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. (e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.“All above operations to be done in order and as directed and specified by the Engineer-in-Charge :, With average thickness of 120 mm and minimum thickness at khurra as 65 mm.DSR 2023- 22.7.1 Please Enable Macros to View BoQ information |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2025 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
