Sales : +91-777 804 8217
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 31-12-2025 | Bid Auto Extn Corrigendum | Bid Auto Extn Corrigendum | 07-01-2026 |
| Sl. No. | Item Description |
| 1 | Taking down cement plaster on brick or stone walls, ceilings etc., without disturbing brick work,including raking out joints, hacking for key, scrubbing down with water and removing of debris outside MD land complete all as specified and as directed by Engineer-in-Charge |
| 2 | Demolition of cement concrete(unreinforcement)in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) and removal of rubbish to outside MD land etc complete all as specified and as per directed |
| 3 | Demolition of reinforced cement concrete of any description in any position (reinforcement cut as required to facilitate demolition) as Roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work and simillar and removing concrete debris and depositing outside MD land all as specified and as directed by Engineer-in-Charge. |
| 4 | Dismantling floor hearth or wall tiling including cement mortar bedding ( but not backing),removing serviceable tiles to store and rubbish out side MD land complete all as specified and as directed by Engineer-in-Charge. |
| 5 | Demolition of brick work/stonemasonry built in cement mortaror cement lime mortar including all quoins, arches, pillars, PCC coping etc, but excluding ashlar facings, dressed stonework and precast concrete articles and removing of debris outside MD landcomplete all as specified and as directed by Engineer-in-Charge. |
| 6 | Taking down chowkats or frames with shutter (without taking off shutter from frame) not exceeding 1.5 sqm each including fittings and removing clear off site after credit for the same is recovered by the dept complete all as specified and as directed . |
| 7 | Material and labour for Building up the profile of structural members by using polymer modified mortarupto 20mmaverage thickness including levelling profiling workrate including following allprocess with material :-(a)Surface preparation of existing concrete components including grinding/rubbing carefully by grinder without damaging the existing concrete and debris removed outside MD area. (b) Providing & applying rust cleaner to existingcorroded reinforcement of approved make (c) Providing and applying two coat of anticorrosive epoxy phenolic rebar protective system to existing as well as new reinforcement(d) Priming cum bonding coat of two component peroxide resinconfirms to ASTM-C-882-91 including providing and inserting 10 mm mild steel shear key bars (minimum 3 nos per sqm), shear key fixing with drilling and epoxy grout wherever required, Scaffoldingat any height & mixing, laying, levelling and finishing including curing and work shall be execute as per manufacturer instruction and from authorised applicator complete all as specified and as directed by Engineer-in-Charge.Note : All materials should be approved make such as Dr Fixit, Fosroc, Sika, Krishnaconchem or equivalent. |
| 8 | Supply and fix mild steel TMT bars, 10mm dia and over cut to length bent to shape required including cranking, bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed by Engineer-in-Charge. |
| 9 | ditto as per item no.8 above but 5mm dia and over up to incl. 10mm dia in stirrups, spacers and binders complete all as specified as directed by Eng-in-charge. |
| 10 | Demolition of reinforced cement concrete of any description (beam, chajja, fins, RCC water tank, roof sla etc) & in any position including necessary scaffolding arrangement (reinforcement cut as required to facilitate demolition) and removing concrete debris and depositing outside MD land all as specified and as directed by Engineer-in-Charge. |
| 11 | Supply & fix MS/TS dowel pins/staple/shear pins including drilling holes in concrete and providing labour but excludeing the materials for grouting the pins etc complete all as specified and as directed by Engineer-in-Charge. |
| 12 | Material & labour for repairing of damaged concrete portion by using superfluid dual shrinkage compensated structural grade M-40 micro concrete of at all levels with all leads and lift as directed including mixing, laying, levelling, finishing and curing complete all as specified and directed by Engineer-in-Charge.Make: Fosroc / SIKA / BASF / Krishna Conchem or equivalent approved . |
| 13 | Material and Labour for reinforced cement concrete (Nominal mix) 1:2:4, using 20mm graded stone aggregates as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs, chajja, shelves and like complete all as specified and directed by Engineer-in-Charge. |
| 14 | Material and labour for formwork using steel shutters or 12mm marine ply to have the smooth finish to pour the micro concrete/ concrete including de-shuttering etc complete all as specified and as directed by Engineer-in-Charge. |
| 15 | Material and labour for providing and applying rust cleaner of approved make over prepared reinforcement, including removing concrete all around reinforcement including from behind the reinforcing bars by manual methods such as hammering the rebar, using wire brushes, chiseling, etc. and applying rust removing solution of approved make with cotton waste swab to reinforcements etc complete as directed by Engineer-In-Charge.Make- Dr FIXIT/ FOSROC/ Krishna Conchem/BASF/Sika |
| 16 | Material and labour for providing and applying two coats of anticorrosive epoxy phenolic rebar protective system IPNet RB of Krishna Conchem or equivalent of approved make and quality comprises of resin and hardener mixed as per manufacturer\"s instructions with minimum 9-10 hours between the coats, sprinkling dry sand when 2nd coat is tacky so as to provide rough finish and ensuring air curing of minimum 10 hours after the top coat before any subsequent treatment etc. including scaffolding etc complete all as specified and as directed by Engineer-in-Charge.Make- Dr FIXIT/ FOSROC/ Krishna Conchem/BASF/Sika as approved by GENote:(a)New Reinforcement shall be measured and paid separately under respective item.(b) Cost of welding deemed to be inclusive in this item of work. |
| 17 | Material and labour for providing and applying a priming cum bonding coat of two component Epoxide Resin conforming to ASTM-C-882-91 of approved make and quality to clean and sound concrete area by brush or any other established method by mixing base and curing agent 2:1 proportion by weight for joining old and new concrete as per technical specifications of manufacturer complete all as specified and as directed by Engineer-in-Charge.Make- Dr FIXIT/ FOSROC/ Krishna Conchem/BASF/Sika as approved by GENote-Work shall be carried out as per the manufacturers specifications & certificate on this account shall be taken from consultant and as approved by Engineer-in-chargeNote for Item No.7 to 17:-(i) The work under Item No. 7 to 17 shall be carried out by authorised applicator only.(ii) Defect liability for these items shall be 5 years from certified date of completion.(iii) Amount of 5% of these items shall be retained during RAR and FB. This amount shall be released after successful completion of Defects liability period as mentioned above.(iv)Non destructive testing shall be got carried out through IIT / NIT / College of Engineering Pune to decide fulfillment of fitness criteria of structure. (v) The test shall be carried out at EACH discrete location or locations decided by GE or testing authority. (vi)The cost of testing shall be deemed to be included in the rate quoted by the contractor. Completion shall be issued by GE after only getting structural stability certificate of EACH respective building from testing authority. |
| 18 | Material and labour for brick work with sub class \"B\" bricks, straight or curved on plan, exceeding 6 m mean radius, built in cement mortar 1:6 complete all as specified and as directed by Engineer-in-Charge. |
| 19 | Material and labour for brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius, in half brick thick walls with old size bricks, built in cement mortar (1:4) complete all as specified and as directed by Engineer-in-Charge |
| 20 | Material and labour for 10 mm thick rendering in Cement Mortar (1:4) on internal wall surface including dubbing out plaster in Cement Mortar (1:6) of any thickness & finishingthe surface even & smooth without using extra cementcomplete all as specified and as directed by Engineer-in-Charge. |
| 21 | Material and labour for rendering 5mm thick plaster in cement mortar (1:3) on concrete surfaces of ceiling and finishing the surfaces even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge. |
| 22 | Material and labour for rendering 15mm thick plaster in cement mortar (1:4) on external surfaces of the brick, PCC blockor concrete surfacesincluding dubbing out plaster in Cement Mortar (1:6) of any thickness & finishingthe surface even & smooth without using extra cement using water proofing compound complete all as specified and as directed by Engineer-in-Charge.complete all as specified and as directed by Engineer-in-Charge. Note: waterproofing compound shall be measured and paid separately |
| 23 | Supply only liquid water proofing compound ISI marked complete all as specified and as directed by Engineer-in-Charge.Make : Pidilite Industries Ltd, Taloja /Super Aquacem (India) Ltd /FOSROC/Siko/Dr Fixit |
| 24 | Demolition of the existing brick coba treatment over roof slab completely including thoroughly cleaning complete all as specified and removal of the demolished material to outside of MD land complete all as specified and as directed by Engineer-in-Charge. |
| 25 | Material and labour for PCC 1:2:4 type B0 (using 12.5 mm graded aggregate) with 2% by weight of cement or as per manufacturer\"s instructionswater proofingas in levelling course, haunching, coping and similar works over RCC roof surface and RCC over head tank top surface including rounded or chamfered on edges and formwork etc complete all as specified and as directed by Engineer-in-Charge |
| 26 | Material and labour for APP modified waterproofingtreatment to parapet wall with following specification including brushing off the surface to receive the treatment obtain the required surface complete as directed by Engineer-in-Charge :- (a) Applying oil bound bituminous primer @ 0.4lit/Sqm of density 0.87-0.89Kg/lit of 250C on the prepared dry roof surface. (b) Laying 4mm thick APP membrane weight not less than 3.90 kg per sqm by torch application with minimum 10cm side lap and 15cm end lap. The laying of membrane shall be got done through an authorized applicator of manufacturer of APP membrane.(c) Over the membrane provide a solar reflective bituminous aluminium paint @ 100ml/ Sqm prescribed by manufacturer complete all as specified.Make:STP Ltd/Texsa India Ltd/IWL Ltd/TIKIDANNote : (i) The laying of membrane shall be got done through an authorized applicator of manufacturer of APP membrane.(ii) Quoted rate includes the disconnection existing tanks of any litres capacity including all fittings, setting aside (for lowering if reqd) for roof treatment & reconnecting and refixing in position including all fittings complete all as directed. |
| 27 | M & L for Hard core of broken stone boulders guage not exc 63 mm, deposited, spread and levelled in layers not exc 15 cm thick watered and framed to a true surface complete all as specified and as directed. |
| 28 | Material and labour for Plain Cement Concrete 1:4:8 type D2 using 40mm graded stone aggregateas in foundation / mass concrete/filling complete all as specified and as directed by the Engineer-in-charge |
| 29 | Material and labour for25mm thick Plain Cement Concrete 1:2:4 type B0 using 12.5mm graded stone aggregate as in levelling course for laying floor tilecomplete all as specified and as directed by Engineer-in-Charge |
| 30 | Material and labour for non skid coloured ceramic tiles (Joint Free) , 7 to 8mm thick (square/rectangular), area of each tile not exceeding 0.11 sqm , in floors etc., set and jointed in neat cement slurry and pointed in white or colour cement to matchoverand including screed bed of 15mm thick in Cement mortar 1:4 etccomplete all as specified and as directed by Engineer-in-Charge.Make: H R Johnson / Orient Bell Tiles / Kajaria / Somany Tiles Ltd / Nitco tiles /Swastik Tiles / RAK tiles/ Orient bell |
| 31 | Material and labour for coloured glazed ceramic tiles of size 350mm x 250mm x 7 mm thick/ 450mm x 350mm x 7mm (or nearest size) ,on vertical surface such as skirting, dado, riser/steps etc, set and jointed in neat cement slurry and pointed in white or colour cement to match over& including cement plaster 10mm thick in Cement mortar 1:4complete all as specified and as directed by Engineer-in-Charge. Make:M/s H R Johnson/M/s Orient Bell Tiles/M/s Kajaria/M/s Somany Tiles Ltd/M/s Nitco tiles/M/s Swastik Tiles / RAK tiles/ Orient bell |
| 32 | Material and labour for 50mm thick cement concrete (1:3:6) type C2, using 40mm graded stone aggregate as in plinth protection laid in panel surface and finishing the surfaces even and smooth without using extra cementcomplete all as specified and as directed by Engineer-in-Charge. |
| 33 | Material and labour for 100mm thick Plain Cement Concrete 1:4:8 type D2,using 40mm graded stone aggregate as in foundation and finished even and fair without using extra cement etc complete all as specified and as directed by Engineer-in-Charge |
| 34 | Material and labour for vibrator moulded (coloured) precast concrete interlocking paver block, of any shape and size conforming to IS 15658-2006 of 60mm thickness, M-35 grade with grey cement and pigment including 25mm thick crushed stone sand cushioning including watering and consolidation below paver block complete all as specified and as directed by Engineer-in-Charge.Make: Mehtab Tiles/Indore/M/S Ultra Tiles/NITCO/Topaz Tiles/Navya Tiles Jodhpur |
| 35 | Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever requiredcomplete all as specified and as directed by Engineer-in-Charge. |
| 36 | M&L for 30 mm thick factory made moulded PVC door (Wood free) consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 20mm x 40mm for stiles as well as top, bottom & lock rail. M.S. frame shall have a coat of metal primer of approved make & manufacturer. The inside panel shall consist of 20mm thick multi-chamber hollow PVC section of 1mm wall thickness, bonded using solvent cement / cynoacrylate adhesive with 5 mm (+0.25) thick moulded PVC sheet of density 600 kg/cbm with 2, 4, 6 raised panel design in plain / prelam colours after routing the moulded design on one side of the inside panel. 5 mm (+0.25) plain / prelam PVC sheet to be pasted using solvent cement / cynoacrylate adhesive on other side of the hollow PVC section. All the four edge of the panel to be sealed with lipping of 10 mm thick & 20 mm wide PVC sheet baton made by sticking 2 nos. foam PVC sheets of 5 mm (+0.25) thickness using PVC solvent cement adhesive. Door edge lipping to be painted with PVC ink of matching colour of Plain/Prelam moulded PVC sheet of door 20 mm thick (5 mm x 4 nos.) thick PVC sheet to be given for lock provision at lock height. Door to be fixed with frame with 3 nos. stainless steel butt hinges of size 100mm x 25mm x 2mm and 50 mm long steel screws drilled suitable to pass through both the walls of the M.S. tube other hardware should be fixed with 25mm x 8mm size steel screws etc, complete as per manufacturer\"s specification and drawing or direction of Engineer-in-charge Make : RAJSHRI / SINTEX / TUFFFLON /M/s Navratan Specialty Chemical LLP – ‘B rand : GIZA’ |
| 37 | Supply and fix solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet, reinforced with M.S. square tube and fixing in opening as per specification & drawing on Serial Page No 151of SSR Part II (pertaining to item No 08095) and edges to be painted to match with prelam sheet complete all as specified and as directed by Engr-in-Charge.Make : RAJSHRI / SINTEX / TUFFFLON /M/s Navratan Specialty Chemical LLP – ‘Brand : GIZA’ |
| 38 | Supply and fix extruded aluminium alloy galvanised mild steel hinge pin butt hinges of size 100 mm long complete all as specified and as directed by Engineer-in-Charge.Make : Classic/ Shalimar/ CLIF/ARGET |
| 39 | Supply and fix aluminium anodised barrel tower bolt of extruded section size 150mm complete all as specified and as directed by Engineer-in-Charge. Make : Classic/ Shalimar/ CLIF/ARGET |
| 40 | Supply and fix extruded aluminium alloy handles fabricated types, anodised, of size 125 mm long complete all as specified and as directed by Engineer-in-Charge.Make : Classic/ Shalimar/ CLIF/ARGET |
| 41 | Supply and fix 15 micron coloured aluminium powder coatedsections for sliding (3 Track) or openable windows, ventilators, doors, partitions etc including fabrication of frame & shutters and fixing with necessary lugs, cleats, rollers, handles, locking arrangement etc including all accessories such as glazing clips and rubber beadings for fixing glass panes / wire mesh in frame complete all as specified and as directed by Engineer-in-Charge.Make : Hindalco/Indal (Indian Al Coy)/Jindal/Associated Profile & Aluminium Ltd/Ajit IndiaNote:(i)Glass panes /wire mesh will be measured & paid separately.(ii) Rubber beading will not be weighed. |
| 42 | Supply and fix 4.0mm thick figured glass, pin headed type ordinary quality fixing with oil putty and glazing clip,in squares not exceeding 0.5 Sqm in each panecomplete all as specified and as directed by Engineer-in-Charge.Make : Modiguard/Atul/Kohinoor/Swastik/Saint Gobain |
| 43 | Supply and fix anodised aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples complete all as specified and as directed by Engineer-in-Charge |
| 44 | Supply and fix 15 micron coloured aluminium anodised grill of design NoDG-101 of Decogrille or equivalent , cut to required size/shape, and fixed in position with and including aluminium beading and frame complete all as specified and as directed by Engineer-in-Charge. Make: DECOGRILLEof Associated group / Royal Alum grill Pvt Ltd or equivalent make as approved by GE |
| 45 | Supply and fix in repair vitreous china squatting pan Orissa pattern of size 580 x 440mm white with integral foot rest, \"P\" or \"S\" trap front and back inlet and including connection to trap and to flushing pipe, anti syphonage pipe etc (excluding flushing cistern & flush pipe) all as specified and as directed by Engineer-in-Charge.Make : Cera/Hindustan/Parryware/Jaguar/Hindware/Johnson |
| 46 | Supply and fix in repair vitreous china wash down, white, water closet pan (pedestal pattern) with \"P\" of \"S\" trap (of size 465mm x 355mm x 265mm),including plastic seat cover to match with colour of WC, closedpattern with flat bottom & cover and chromium plated mild steel or aluminium anodized hinging device including connecting to trap and flushing pipe, anti-syphonage pipe etc complete all as specified anddirectedby Engineer-in-Charge.Make : Cera/Hindustan/Parryware/Jaguar/Hindware/Johnson |
| 47 | Supply and fix in repair PVC valveless, syphonic action type low level flushing cistern 10 ltr capacity white with inlet ball valve, floatand handle including brackets, flush pipe of polyethylene of low or high density or PVC 32mm dia including connection to pipe and fixing of chains and pull or lever complete all as specified and as directed.Make : M/S Johnson Peddar/ Parryware/ RAK Ceramics/ CERA |
| 48 | Supply and fixin repairs vitreous china wash hand basin white flat back size 580 x 450 mm excluding taps, waste chain and plug and porcelain stopper but including CI brackets, cutting for and pinning in ends of brackets or erecting stand including 32mm bore discharge pipe with waste coupling of PTMT etc complete all as specified and as directed by Engineer-in-Charge.Make : CERA/ RAK Ceramics/ Parryware/ Hindware/ Neyveli Ceramics (Neycer)/ Jaquar/ Kajaria (KEROVIT) |
| 49 | Supply and fix in repair vitreous china bowl urinal, half stall type with grating and urinal for discharge pipe, waste pipecomplete including providing and fixing plugs, bedding urinal against wall in CM securing urinal to plugs with and including 60mm long brass screws, pointing around, fixing cistern with brackets, flush pipe grating and union for discharge pipe complete all as specified and as directed by Engineer-in-Charge.Make: Parryware/Cera(Iquality)/Jaguar/Hindware/Johnson |
| 50 | Supply and fix in repairs pillar taps fancy type cast copper alloy with capstan head, chromium plated, screwed down high pressure, with or without lettered ‘hot’ or ‘cold’ with long screwed shanks and fly nuts, screwed for iron pipes, 15mm bore complete all as specified and directed by Engineer-in-Charge.Make : Jaquar/ Marc/ CERA/ Kohler/ Player |
| 51 | Supply and fix in repairs 15mm bore bib taps, fancy type, chromium plated, cast copper alloy, with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule all as specified and as directed by Engineer-in-Charge.Make : Jaquar/ Marc/ CERA/ Kohler/ Player |
| 52 | Supply and fix in repairsstop valve, cast copper alloy, fancy type, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipes or for unions of 15mmbore complete all as specified and directed by Engineer-in-ChargeMake : Jaquar/ Marc/ CERA/ Kohler/ Player |
| 53 | Supply and fix in repair Swivel Shower fancy type of PTMT, 125mm, any colour for fixing with 15 mm pipe (Minimum weight 40gms) complete all as specified and as directed by Engineer-in-Charge.Make : Prayag / R.S. Industries (POLYTUF) |
| 54 | Supply and fix in repairs concealed stop valve, cast copper alloy, fancy type, with long shank and cup (concealed type) screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipes or for unions of 15mmbore complete all as specified and directed by Engineer-in-ChargeMake : Jaquar/ Marc/ CERA/ Kohler/ Player |
| 55 | Supply and fix in repair 600 mm x 450 x 5mm mm bevelled edge mirror of selected quality glass, with PVC moulded frame decorative type, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup and washers complete all as specified and as directed by Engineer-in-Charge.Make : Modi/ Atul/ Saint Gobain |
| 56 | Taking up or down steel tubing and connections for 20mm bore of pipe complete all as specified and directed. |
| 57 | Refixng old steel tubing and connection in new or old position (walls, ceiling, floor etc ) bore of pipe in 20mm dia complete all as specified and directed. |
| 58 | Supply and fix mild steel tubing medium grade 20mm, galvanized iron with all fittings such as Tees, elbows, sockets, bends, unions, short pieces, nipples, brass nuts and diminishing pieces complete all as per IS 1239 including fixed to wall / ceiling or laid in floor with suitable size GI clamps and making good disturbed surfaces as per existing surfaces complete all as specified and as directed by Engineer-in-Charge. Make: Tata / Jindal / Surya Prakash / Zenith |
| 59 | Taking up or down steel tubing and connections for 15mm bore of pipe complete all as specified and directed. |
| 60 | Refixng old steel tubing and connection in new or old position (walls, ceiling, floor etc ) bore of pipe in 15mm dia complete all as specified and directed. |
| 61 | Supply and fix mild steel tubing medium grade 15mm, galvanized iron with all fittings such as Tees, elbows, sockets, bends, unions, short pieces, nipples, brass nuts and diminishing pieces complete all as per IS 1239 including fixed to wall / ceiling or laid in floor with suitable size GI clamps and making good disturbed surfaces as per existing surfaces complete all as specified and as directed by Engineer-in-Charge. Make: Tata / Jindal / Surya Prakash / Zenith |
| 62 | Supply and fix in repairsstop valve, cast copper alloy, fancy type, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipes or for unions of 20mmbore complete all as specified and directed by Engineer-in-ChargeMake : Jaquar/ Marc/ CERA/ Kohler/ Player |
| 63 | Supply and fix in repairs rotational molded polyethylene water storage tanks 1000 litres capacity with inlet connections, three layer (cylindrical or vertical with closed top) HDPE with ISI marked, hoisted and fixed in position either inside or out side of the building, including S&F 20mm float valve 20mm dia GI pipe medium grade washout pipe 450mm long with plug and 20mm dia GI pipe medium grade overflow pipe 600mm long with fitting andsecuring access coversetc complete all as specified and directed by Engineer-in-ChargeMake : Sintex / Polycon, Jaipur / Rotex / Infra |
| 64 | Supply and fix ball in repair ball valves, brass ,high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed of 20 mm bore complete all as specified and as directed by Engineer-in-Charge Make : Leader/Zoloto/Seiko/Sant/GEM |
| 65 | Supply and fix PVC connection, 15 mm size 600 mm long both end socket fix complete all as specified and as directed by Engineer-in-Charge. |
| 66 | Supply and fixin repairs brass chromium plated towel rail, 20mm dia, D type, 60cm long, between flanges complete all as specified and as directed by Engineer-in-Charge.Make : Crown / Jindal / Essess / Swastik |
| 67 | Supply & Fix soap dish CP complete all as specified and as directed by Engineer-in- Charge. Make : CERA/Hindustan/Parryware/Jaguar/Hindware/ Johnson |
| 68 | Cutting chases, pinning exe 10 cm but n exc 20cmin. girth in brick/stone wallfor fixing of PVC pipe/GI pipe of 15 & 20 mm bore concealed in walletc., and making goodin cement mortar 1:6 to match the existing surfaces complete all as specified and as directed by Engineer-in- Charge. |
| 69 | Supply and fix in repairs PVC (SWR), type B,single socketed rain water/soil waste/vent pipes with rubber ring joints, 110mm dia, laid in trenches or in floors complete all as specified and as directed by Engineer-in-Charge..Make: Supreme/ PRINCE (Ultrafit)/ Kisan/ Finolex/ Astral |
| 70 | Supply and fix in repairs PVC (SWR), type B,single socketed rain water/soil waste/vent pipes with rubber ring joints, 75mm dia, laid in trenches or in floorscomplete all as specified and as directed by Engineer-in-Charge..Make: Supreme/ PRINCE (Ultrafit)/ Kisan/ Finolex/ Astral |
| 71 | Supply and fix in repairs PVC (SWR), type B,single socketed rain water/soil waste/vent pipes with rubber ring joints, 110mm dia, fixed to walls complete all as specified and as directed by Engineer-in-Charge..Make: Supreme/ PRINCE (Ultrafit)/ Kisan/ Finolex/ Astral |
| 72 | Supply and fix in repairs PVC (SWR), type B,single socketed rain water/soil waste/vent pipes with rubber ring joints, 75mm dia, fixed to walls complete all as specified and as directed by Engineer-in-Charge..Make: Supreme/ PRINCE (Ultrafit)/ Kisan/ Finolex/ Astral |
| 73 | Supply and fix in repairs PVC (SWR) floor trap, plain with grating including jointing with solvent cement, outlet dia 75mm complete all as specified and as directed by Engineer-in-Charge. Make : Supreme/ PRINCE (Ultrafit)/ Kisan/ Finolex/ Astral |
| 74 | Supply and fix in repairs PVC (SWR) bends any radius, 75mm dia. complete all as specified and as directed by Engineer-in-ChargeMake : Prince / Supreme / Finolex |
| 75 | Supply and fix in repairs PVC (SWR) bends any radius, 75mm dia. With access door complete all as specified and as directed by Engineer-in-ChargeMake : Prince / Supreme / Finolex |
| 76 | Supply and fix in repairs PVC (SWR) bends any radius, 110mm dia. complete all as specified and as directed by Engineer-in-ChargeMake : Prince / Supreme / Finolex |
| 77 | Demolition and breaking up drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortar of size 100mm boreas bed to drain pipes including packing under and haunching against the sides of pipes complete all as specified and as directed by Engineer-in-Charge.Note- Earth work shall be measured and paid separately. |
| 78 | S&F for 75mm thick steel fibre reinforced (SFRC) factory made man hole cover with iron frames (medium) complying to the standard specifications as mentioned in the IS 12592 BIS Standard, minimum load bearing capacity 5 ton/sqm, in square, rectangular or circular shape complete all as specified & as directed. |
| 79 | Material and labour for reinforcedconcrete pipes, 150mm bore withcollars, class NP-2, laid in trenches and jointed in cement mortar 1:1 with spun yarn etc complete all as specified and as directed by Engineer-in-Charge.Make : Indian hume pipes/ Everest/ Himalaya/ Thuluvananikal Pipes |
| 80 | Material and labour for cement concrete 1:4:8,type D2 (using 40mm graded stone aggregate), as bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested in as specified in Clause 18.68 of MES schedule Part I, bore of pipe 200mm bore of pipe complete all as specified and as directed by Engineer-in-Charge |
| 81 | Material & Labour for cutting into existing manholes for 100mm internal dia of pipes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete (1:2:4) type B1, smooth finished and reforming benching as required complete all as specified and as directed by Engineer-in-Charge. |
| 82 | M&L for Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in deep for foundation, laying pipes etc or for shaft, walls, manholes, pier holes etc not exceeding 10 sqm on plan and not exceed 1.5m in depth and getting out in soft/loose soil complete all as specified and as directed by Engineer-in-Charge |
| 83 | Returning, filling in including spreading, levelling, watering and well ramming soil in layers not exceeding 25 cm thick complete all as specified and as directed by the Engineer-in-Charge |
| 84 | Removing excavated material to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and as directed by Engineer-in-Charge |
| 85 | Material and labourfor preparation of old plastered surfaces of walland applying three coats of white wash complete all as specified and directed by Engineer in Charge. |
| 86 | Material and labourfor preparation of newlyplastered surfaces of ceiling and applyingthree coats of white wash complete all as specified and as directed by Engineer-in-Charge. |
| 87 | Material and labourfor preparation of old plastered surfaces of ceilingand applying two coats of white wash complete all as specified and directed by Engineer in Charge. |
| 88 | Material and labour for complete removal of existing treatment of plastered wall surface and applying one coat of cement base paint as per manufacturer\"s recommendation upto a height of bldgroofincluding formwork/scaffolding/ladders and safety belts with precautions etccomplete all as specified and as directed by Engineer-in-Charge.Make : Super Snowcem/ Duracem/ Aquacem/ Shalimar/ Berger |
| 89 | Material and labour writing letters or figures (Block, Roman, Italic or Indian) to building withflurocent synthetic enamel paintofEACH30 cm highin words and figures such as (P-23, P-25likeetc) over synthetic enamel fluorescent painted surface complete all as specified and as directed by Engr-in-Charge. |
| 90 | Earth work in excavation by mechanical means (Hydraulic excavator)/ in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m complete all as specified and as directed by Engr-in-Charge.. |
| 91 | Material and labour for Pre-cast cement concrete block masonry 1:3:6 type C1, (using 20mm graded stone aqggregate), with solid blocks, exceeding 10 cm in width and setting in cement mortar 1:4 complete all as specified and as directed by Engineer-in-Charge. |
| 92 | Removing excavated material to a distance exceeding 250 m but not exceeding 500 m and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and as directed by Engineer-in-Charge |
| 93 | M & L for extra for forming fair finished drain or channel 30cm inner girth in cement concrete with using extra cement, including forms, moulds, mitred/stopped ends etc complete all as specified and as directed. |
| 94 | Material and labour for rolled mild steel sections as in roof trusses (framed), trussed, purlins, crane gantries, rails, and fastenings and heavy bracket framing, (beam, tee, angle, channels or flat sections) including notching, drilling, fitting, riveting and / or welding or connecting with bolts and nuts (including rivets or bolts and nuts) conforming toFe 410 W Gde E- 250, Quality B complete all as specified and as directed by Engineer-in-Charge. |
| 95 | Supply and fix Pre- painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick as per approved profile of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws or L type or J type or cranked hook bolts or as per manufacture instruction complete all as specified and as directed by Engineer-in-Charge.Make: JINDAL / INDALCO / TATA/ HINDALCO / ASSOCIATED Profiles and Aluminium Ltd / ESSAR colour coated sheets |
| 96 | Supply and fix Pre- painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick as per approved profile of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws or L type or J type or cranked hook bolts or as per manufacture instruction complete all as specified and as directed by Engineer-in-Charge.Make: JINDAL / INDALCO /TATA/HINDALCO / ASSOCIATED Profiles and Aluminium Ltd / ESSAR colour coated sheets |
| 97 | Material & labour for Rolled mild steel as in MS base plates (plain or chequered), channels , square cut or notched ( ordinary and counter sunk) forming holesincluding cutting ,welding or connecting conforming to Fe-290 (Gde E-165) complete all as specified and directed by Engineer in charge. |
| 98 | Supply & Fix hilti wedge anchor fastner, 12mm dia 100mm long or similar approved make fixed with anchor grout lokfix E77 or approved make of similar characteristics, the thixotropic nature of lokfix polyester resin grout P reduces flow of grout out of the hole, in overload or horizontal holes incl. drilling holes of required sizes cleaning with the same with air pressure and filling with chemical as secified above placing of MS plate of required size and shape and drilling/ fixing the anchor bolt fastner complete all as specified and directed by Engineer-in- Charge. Note:- All MS items weight will be measured seperatly. |
| 99 | Material and labour for plain cement concrete 1:2:4type B-1 (using 20mm graded stone aggregate) as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, holstring courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, kerbs, water troughs, bed plates, concrete block for hold fast etc and the like including necessary form work for fair finished surfaces including weathering, slightly rounded or chamfered angles and throating, as directed etc complete all as specified and as directed by Engineer-in-Charge. |
| 100 | Material and labour for preparing new steel surfaces /previuosly untreated surface of any description, over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed by Engineer-in-Charge.Make: Make: Asian Paints/ Nerolac Paints/ Dulux ( Akzonobel)/ Nippon Paint India Pvt Ltd |
| 101 | Material and labour for preparation of old plastered wall surface and applying two coats of Acrylic weather proof coat 100% exterior grade paint over one coat ofacrylic weather coat primer over 1mm thick layer of external grade puttycomplete all as specified and as directed by Engineer-in-Charge.Make : APEX ULTIMA” of Asian Paints/ “WEATHER COAT ALL GUARD” of Berger Paints/\"EXCEL TOP GUARD” of Nerolac/ “DULUX WEATHERSHIELD MAX” of ICI India |
| 102 | Material and labourfor complete removal of existing treatment on wall surfaces and applying two coats of distemper oil emulsion with roller including a coat of white JK Birla wall care putty 2mm thick over a coat of alkali resistant wall primer complete all as specified and directed by Engineer in ChargeMake: M/s SHALIMAR / M/s BERGER / M/s NEROLAC /M/s ASIAN (Tractor Brand) |
| 103 | Supply and install wall-mounted split units indoor/outdoor, operating voltage 110 to 285volts, 50Hz complete with cordless remote control unit and with in-built anti-microbial air filtration, dehumidifier for better indoor air quality with minimum 5starrating, DNNS Self Heal Coating and EER upto 3.2of capacity 2TR, inverter type, 6in1convertible or adjustable mode, high swing typel eft}/right}/up}/down}, with high ambient temperature upto 52degree celcius including fixing of voltage stabilizer 5KVAwith digita ltemperature display and MS bracket for outdoor unit on wall with copper cooling tube extra upto 15RMetccomplete all as specified and directed by Engineer in Charge.Make: 1.5TR- 4503517/ 245VVectra Plus or equivalent in BlueStar/ Lloyd/Daikin/Hitachi |
| 104 | Material and labour for sub main wiring with two single core 04sqmm multistranded copperconductor, FRLSH PVC insulated, unsheathed cable includingPVC casing Caping heavy grade}, ISI marked, as per IS for sub main wiring including 04 sqmm FRLSH PVC insulated and unsheathed stranded copper conductoras earth wire in surface /recess complete all as specified and directed.Note: 1. Two runs of 04sqmm copper conductor cable, one run of 04sqmm copper conducto rand one run of PVC casing caping will be measured as one unit.Make of Cable-Plaza, Finolex, Havells, PolycabMake of PVC casing capping-Anchor, Modi, Pressfit, Precision, Astral, Panasonic Anchor, Polycab, Presto Plast, Supreme |
| 105 | Supply and fix Single pole and neutral enclosure with a 3 pin plug and socket of 16 Amps complete with onesingle pole MCB 20 Amps 240volts, fixed on wall complete all as specified and as directed by Engineer-in-Charge. Make: L&T/ABB/Siemens/Schneider/Havells |
| 106 | Material and labour for point wiring concelead type with proper colour coding complete with and including PVC insulated unsheathed, flexible bright annealed multi stranded copper conductor single core FRLS cable 1.5 Sqmm (22/0.30) 1100 volt gradeconfirming to IS 694drawn through in and including (medium grade) rigid non metallic PVC conduit pipe 25 mm size ISI marked with conduit accessories / fittings / junction box / inspection covers etc of ISI marked and cutting chases forconcealed conduit with all surfaces by means of screws and sunk / cup washers, with Modular metal flush box including white cover plate with frame for mounting of switches sockets fan regulators etc including 1.5sqmm (22/0.30) 1100 volts grade PVC insulated FRLS unsheathed flexible, multi stranded copper conductor cable (green colour) as continuous earthwire connected to metallic bodies of luminaries / fans etc at one end and to common earth dolly at other endfor one light / Fan / Exhaust fan / bell point controlled by one, one way switch all as specified and as directed including taking down unserviceable pointMake of Cable-Plaza, Finolex, Havells, PolycabMake of PVC conduit-Anchor, Modi, Pressfit, Precision, Astral, Panasonic Anchor, Polycab, Presto Plast, Supreme |
| 107 | Supply and fixsingle door, sheet metal enclosure powder coatedMCB DB SPN 4 way with earth bar, 415 volt, conforming to IS 13032-1991 including taking down underviceable DB complete all as specified and as directed by Engineer-in-Charge.Make: Havells /Legrand / Larsen &Toubro/ ABB/ Siemens/ Schneider/ Indo ASIAN/ C & S Electric/ Bhartia Cuttler Hammer (BCH) |
| 108 | Supply and fix MCB SPN, 32 Amps, 240 volts,10 KA, \"C\" curve including taking down unserviceable complete all as specified and as directed by Engineer-in-Charge.Make : Legrand / L&T / Havells / ABB / Siemens / Schneider |
| 109 | Supply and fixMCB SP, 5 Amps to 32 Amps, 240 volts,10 KA \"C\" curve including taking down unserviceable complete all as specified and as directed by Engineer-in-Charge.Make : Legrand / L&T / Havells / ABB / Siemens / Schneider |
| 110 | S&F celling rose, 3 phase/PVC/polycarbonate isolated body ISI(marked) completeall as specified and directed.Make : Legrand /crabtree/ Honeywell/ Anchor |
| 111 | S&F modular switch , SP, one way, 6A, one module, 240 V,all as per relevant IS complete all asspecified and directed.Make :Anchor(Panasonic)r / Legrand / Havells/.Crabtree/Leader |
| 112 | Supplying, laying,connecting, testing & commissioning LT UG XLPE insulated, heavy duty, 1100 V grade (earthed ) electric cable with aluminium conductor, served with an inner sheathing of PVC tape, armoured with galvanised steel wire or tape and overall PVC sheathed of size 10 Sqmm x 2 core, laid in trenches or passing through pipe or fixed to wall, making all connections with and including provision of necessary glands, lugs, bushing etc as requiredincluding taking down old unserviceable cable complete all as specified and as directed by Engineer-in-Charge Make: Cable Corporation of India (CCI)/ Asian Cable Co, Chattisgarh/ Finolex/ Polycab/ Gloster/Universal/ RPG Cables Ltd , Thane/ Havells India Ltd/ RR Kabel/ KEI Industries Ltd(KEI) |
| 113 | Supply and fix LED lights fitting 1x 20 W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose including 02 Nos of PVC square /round boxes , screws clips including taking down existing light fittings etccomplete all as specified and as directed by Engineer-in-Charge.Make:Phillips Cat No BNO21C LED20S PSU CW GR S2 or equivalent of Havells cat part No LHEXARP7SN1W020 / Bajaj, as approved by GE. |
| 114 | Supply, fix and jointing steel water tubing of 25mm bore medium grade, galvanised iron with all fittings such as Tees, elbows, sockets, bends, unions, short pieces, nipples, brass nuts and diminishing pieces complete all as per IS 1239 including fixed to wall / ceiling or laid in floor with suitable size GI clamps including taking down existing GI pipe and making good disturbed surfaces as per existing surfaces complete all as specified and as directed by Engineer-in-Charge.Make: Tata / Jindal / Surya Prakash / Zenith |
| 115 | Material and labour for earthing complete with Galvanised steel earth plate electrode 60cm X 60cm X 6 mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of earth the plate not less than 1.5 metres below normal ground level, connected to plate with GI earth wire 32 x 6mm GI earth strip, 7.5m long from earth point to test point and other end connected to control board / panel / equipment, laid under floors/plinths or fixed on walls or concealed in wall etc by means of bolts, nuts, check nuts and washers made out of galvanized iron or steel with provision of charcoal & common salt not less than 50Kg, in each earthing packed up to maximum 30 cm on both side of plate and GI strip protected by 40mm bore light grade galvanized iron pipe complete all as shown in electrical plate No. 3 of MES schedule Part I, 2009 with PCC 1:3:6, type C1 in chamber wall with CI cover and frame, watering pipe of size 20mm dia medium grade, 0.63mm thick GI sheet funnel with wire mesh and engraving of earth marking on nearby structure/ building with cement mortar 1:4 plate of size 200mm x 150mm x 15mm thick including necessary excavation and earth work in any type of soil/strata & testing complete all as specified and as directed by Engineer-in-Charge.Note :- (i) Contractor should submit test report of earthing after installation to Engineer -in-Charge (ii) All joints shall be made with welding to get proper conductivity |
| 116 | Supply, install, test and commission LED street light fitting 35 watts, rating, separate individual peanut plated lens and aluminium reflector housing made of LM6 pressure die cast aluminium. Optical cover toukghned glass only, impact resistance>IK05 IP protection not less than IP66, protection should be class I vibration as per IEC 60598, product standard IS 10322/IEC60598, all the component such as driver, surge protector should be of same make.Driver should be moulded type with operating voltage 140V270V, driver frequency 50 Hz, Lumen output should not be less than 100 lumen/watt and luminaire driver ckt,moulded type weather proof construction with separate surge protection device 10 KA rating and separate connector block for termination of incoming cable connection, including necessary brackets, clamps, nuts, bolts for fixing of light on wall including taking down unserviceable lights complete all as specified and directed byEngineer-in-Charge.Make - Surya /Phillips/Bajaj/Havells/Osram/General Electric/Crompton |
| 117 | Supply and fix in repairs exhaust fan, AC, single phase, 230V, 250mm sweep, 1200 RPM, 5 blade, metal bodycomplete all as specified and as directed by Engr-in-Charge. Note: Old exhaust fan will be deposited at MES store yardMake- Crompton Greaves, Bajaj, Orient, Khaitan, Havells |
| 118 | Supply and fixgun metal globe/ gate valve, 25mm bore, with iron wheel head, screwed both ends for iron pipes, ISI marked and fixed with suitable size of new union, nipple and reducer complete all as specified and as directed by Engineer-in-Charge.Make : Leader/Zoloto/Seiko/Sant/ Essco/Prayag |
| 119 | Supply and fix LEDlightfittings 1 x 10Watts, bulk head luminaries including LED light driver holder connecting up with three core copper flexible wire of suitable size from ceiling roseto fitting with fixing accessories including taking down existing light fittings etc complete all as specified and as directed by Engineer-in-Charge.Make : Havells Cat partNo. LHEXCGP7UN5W013 or equivalent in Bajaj/Phillips |
| 120 | Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in deep for laying UG cables and getting out in soft/loose soil complete all as specified and as directed by Engineer-in-Charge |
| 121 | Material and labour for cutting the existing bitumen road / hard standing etc of any description of surfaces and excavation in trenches not exceeding 45cm wide and depth not less than 60cm for passing of UG cable and making good thedisturbed surface filled with excavated material and top 200mm depth with PCC 1:2:4, type B1 using 20mm graded stone etc complete all as specified and as directed by Engineer-in-Charge |
| 122 | Supply and lay double wall corrugated (DWC) HDPE pipe 40/ 32 mm outer dia , as per IS-16205 including couplers and bend for cable protection laid in trenches etc complete all as specified and as directed by Engineer-in-ChargeMake : TELEREX 450N/ Rex Polyextrusion Ltd/ Finolex/ Prince Pipes and fittings ltd/Kisan/Supreme/JAIN IRRIGATION SYS/ Astral |
| 123 | Note:Deduct Credit for demolished / dismantled material of Rs. (-) 35,650.00 (Minus) as listed in Schedule of Credit.Tenderers will not quote against this item being a tentative amount to be considered to arrive at the \"Contract Sum\" |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
