Tender For Addition/ Alteration And Special Repairs To Certain Buildings For Dromi At Npol, Kochi And At Uarf, Kulamavu Alongwith Provision Of Arboriculture Work Along Security Wall Of Main Campus At Npol, Kochi, Kochi-Kerala

TDR : 52976882

Tender Notice
BOQ

18 Days Left

Kochi , Kerala

Tender Brief : Tender For Addition/ Alteration And Special Repairs To Certain Buildings For Dromi At Npol, Kochi And At Uarf, Kulamavu Alongwith Provision Of Arboriculture Work Along Security Wall Of Main Campus At Npol, Kochi

Document Fees
Refer document

EMD
₹ 749000.0 /-

Tender Value
₹ 3.74 Crore /-

Submission Date
06-01-2026

Competition Type
Indian

Bidding Type
Tender

Need a Business Loan? Apply Now !


1	(PART- I)ADDITIONAL/ALTERATIONS AND SPECIAL REPAIRS TO DROMI (BLDG NO. P-76) AND ITS SERVANT QUARTERS (BLDG NO. P-77) AT NPOL KOCHI
2	CIVIL WORKS
3	Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.
4	Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and for all lift
5	Supplying chemical emulsion in sealed containers including delivery as specified.
6	Chlorpyriphos/ Lindane emulsifiable concentrate of 20%
7	Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) :
8	Along external wall where the apron is not provided using chemical emulsion @ 7.5 litres / sqm of the vertical surface of the substructure to a depth of 300mm including excavation channel along the wall & rodding etc. complete: With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration
9	Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor:
10	With Chlorpyriphos/Lindane E.C. 20% with 1% concentration
11	Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources).
12	Providing and laying cement concrete 1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size ) in string and lacing courses,coping , bed blocks ,anchor blocks , and window cills and like including necessary shuttering and centring at all Levels and locations etc., complete all as shown in drawings and as directed .
13	Providing and laying in position ready mixed M-25 grade concrete for reinforced cement concrete work, using cement content as per approved design mix, manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work, including pumping of R.M.C. from transit mixer to site of laying , excluding the cost of centering, shuttering finishing and reinforcement, including cost of admixtures in recommended proportions as per IS:9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in – charge.(Note :- Cement content considered in this item is @ 330 kg/cum.Excess/less cement used as per design mix is payable/recoverable separately).
14	All works upto plinth level
15	All works above plinth level upto floor v level
16	Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.
17	Thermo-Mechanically Treated bars of grade Fe-500D or more
18	Centering and shuttering including strutting, propping etc. and removal of form work for :
19	Centering and shuttering including strutting, propping etc. and removal of form work for : Foundations, footings, bases for columns.
20	Centering and shuttering including strutting, propping etc. and removal of form work for Columns, piers, abutments, pillars, posts and struts.
21	Providing and layingplinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth With Addtional Cement Motor 1:4 a floating coat of neat cement finish andfiliing the construction joints with sand bitumen ete., complete all as directed.
22	Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with : Cement mortar 1:6 (1 cement : 6 coarse sand)
23	Providing Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand)
24	Providing brick work of half brick thickness using M-50 Grade bricks in CM 1:4 in walls at all heights as per specification including scafolding curing and providing 2 Nos of 6mm dia MS round bars on every third course etc. Complete.
25	Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.
26	15mm thick plastering in cement motor 1:6 ( 1cement : 6 fine sand ) on internal surfaces of walls finished smooth and even etc., complete at all levels and locations
27	12mm thick cement plastering in CMC (1:6)
28	18mm thick cement plastering on external surfaces of brick concrte surfaces in two layers consisting of 6mm thick cement motor 1:3( 1 cement : 3 fine sand ) top coat mixed with integralwater proofing compound over a base coat 12mm thick cement motar 1:5 ( 1 cement : 5 coarse sand ), finished sand face ete., complete at all levels and locations.
29	Complete Removal of existing treatement/ dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.
30	Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre. of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. over a coat ofwater thinnable cement primer on wall surface having VOC content less than 50 grams/litre.
31	Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.
32	Finishing walls with Acrylic emulsion Smooth exterior paint of required shade (anti fungus paint):(Two or more coat applied @ 1.67 ltr/ 10 sqm) over a coat Water thinnable cement primer.
33	Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :One or more coats on new work
34	Providing and laying antiskid Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.
35	Providing and fixing 1st quality ceramic glazed walltiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of anysize as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.
36	Providing and laying Anti Skid Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade,over 20 mm thick bed of cement mortar 1:4(1 cement: 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. Complete.
37	Size of Tile 600x600 mm
38	Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade,over 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete.
39	Size of Tile 600x600 mm
40	Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :
41	25 mm thick
42	Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.
43	Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.
44	Granite stone slab colour black, Cherry/Ruby red :Area of slab upto 0.50 sqm
45	Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.
46	Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.
47	Polished Granite stone slab of all colour and texture exceptBlack, Cherry/Ruby Red.
48	Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.Marble work
49	Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. Complete.
50	Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware\"s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.
51	Three track three panel sliding window with two glazed and one wire mesh panelsusing R3 series with frame and glazed and fly proof sash with zinc alloy powder coated handle on every glazed panel along with multi point locking system
52	Providing and fixing factory made uPVC white colour fixed glazed ventilators comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), , uPVC extruded glazing beads ofappropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware\"s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge.
53	Using R1 series with frame ( Height upto 0.9m)
54	Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge. With brass cover plate minimum 1.25 mm thickness
55	Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete Fixed to openings /wooden frames with rawl plugs screws etc.
56	Providing and fixing pressed steel door frames conforming to IS: 4351,manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge: Profile B ,Fixing with adjustable lugs with split end tail to each jamb
57	Providing and fixing ISI marked flush door shutters conforming to IS :2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws.
58	Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross-section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminate shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame.
59	Providing and fixing to existing door frames. 30 mm thick Fiber glass Reinforced Plastic (F.R.P.) flush door shutter in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF)/Polystyrene foam to be used as filler material throughout the hollow panel, casted monolithically with testing parameters of F.R.P. laminate conforming to table - 3 of IS: 14856, complete as per direction of Engineer-in-charge.
60	Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Ceosetory windows & other Frames/Chowkhat comprising of virgin PVC polymer of K value 58- 60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. Frame size 65 x 125 mm
61	Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter 30 mm thick of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction nof Engineer-In- Charg
62	Supplying and fixingat site, Patch fitting doors with 10mm thick clear toughened glass fixed onto S.S.Patch fittings, with floor springs & all requisite hardware such as handles, lock etc, (all ofDORMA /OZONE OR equivalent make).
63	Providing and fixing ISI marked M.S. pressed butt hinges bright finished with necessary screws etc. Complete :
64	100x58x1.90 mm
65	125x65x2.12 mm
66	Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. Complete :
67	125 mm
68	Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :
69	200x10 mm
70	150x10 mm
71	Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. Twin rubber stopper
72	Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 300x16 mm
73	Providing and fixing chromium plated brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.
74	Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.
75	Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, i.e fixing the railing with necessaryaccessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.,)
76	Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer\"s specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :12.5 mm thick tapered edge Glass Reinforced Gypsum (GRG) board conforming to IS: 2095- (Part 3):1996 (Boards with BIS certification marks)
77	Providing and Fixing 15 mm thick densified tegular edged eco friendly light weight calcium silicate false ceiling tiles of approved texture of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanised steel sections (galvanising @ 120 grams per sqm including both side) consisting of main ‘T’ runner suitably spaced at joints to get required length and of size 24x38 mm made from 0.33 mm thick (minimum) sheet, spaced 1200 mm centre to centre, and cross “T” of size 24x28 mm made out of 0.33 mm (Minimum) sheet, 1200 mm long spaced between main’T’ at 600 mm centre to centre to form a grid of 1200x600 mm and secondary cross ‘T’ of length 600 mm and size 24 x28 mm made of 0.33 mm thick (Minimum) sheet to be inter locked at middle of the 1200x 600 mm panel to from grid of size 600x600 mm, resting on periphery walls /partitions on a Perimeter wall angle pre-coated steel of size(24x24X3000 mm made of 0.40 mm thick (minimum) sheet with the help of rawl plugs at 450 mm centre to centre with 25mm long dry wall screws @ 230 mm interval and laying 15 mm thick densified edges calicum silicate ceiling tiles of approved texture in the grid, including, cutting/ making opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever required. Main ‘T’ runners to be suspended from ceiling using G.I. slotted cleats of size 25x35x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm G.I. adjustable rods with galvanised steel level clips of size 85 x 30 x 0.8 mm, spaced at 1200 mm centre to centre along main ‘T’, bottom exposed with 24mm of all Tsections shall be pre-painted with polyster baked paint, for all heights, as per specifications, drawings and as directed by Engineer-in-Charge.Note :- Only calcium silicate false ceiling area will be measured from wall to wall. No deduction shall be made for exposed frames/opening (cut outs) having area less than 0.30 sqm.The calcium silicate ceiling tile shall have NRC value of 0.50 (Minimum), light reflection > 85%, non- combustible as per B.S. 476 part IV, 100% humidity resistance and also having thermal conductivity <0.043 w/mK.
78	Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations:
79	Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment.
80	Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs.
81	After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge.
82	Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep.
83	The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.“All above operations to be done in order and as directed and specified by the Engineer-in-Charge : With average thickness of 120 mm and minimum thickness at khurra as 65 mm.
84	Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion,
85	Single socketed pipes. 110 mm diameter
86	Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in – charge.
87	Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix)
88	Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.
89	Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.For thickness of tiles 10 mm to 25 mm
90	Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceable material with in 50 meters lead as directed by Engineer-in-charge
91	Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead :
92	Of area 3 sq. metres and below
93	Of area beyond 3 sq. metres
94	Dismantling G.I. pipes (external work) including excavation and refilling trenches after taking out the pipes, manually/ by mechanical means including stacking of pipes within 50 metres lead as per direction of Engineer-in-charge : 15 mm to 40 mm nominal bore
95	Removingthe all kinds of Sanitary fittings like EWC, Urinals, wash hand basinsincluding stacking of items within 50 metres lead as per direction of Engineer-in-charge :
96	Supplying and fixing European Water Closet with cistem set comprising of.
97	White vitreous china pedistaltype water closet ( European type) with seat and lid,10 liter concealed flushing cistern & C.P . Flush bend with fittings & C.Ibrackets , 40mm flush bend , overflow arrangement with specials of standard make and mosquito prrof coupling of approved muncipal design complete, including painting of fittings and brackets , cuttings and making good the walls and floors wherever required .
98	15mm CPBrass stopangle cock fixed between GIand PVC inlet
99	15mm heavyqualityflexible PVC inlet connection with CPBrass hexagonalcheck nuts washer at both ends
100	Supplying and fixing in position best quality and approved make CPtoilet paper roll holder with necessary CP brass Screws and washers fixed to wall etc., complete all specified and directed.
101	Toilet Roll Holder With Stainless Steel Flap AKP-35753PS
102	Supplying and fixing in position best quality and approved make CPsoapcontainer necessaryincluding CP Screws and washers fixed to wall etc., complete all specified and directed.
103	Soap Dish Make Jaquar Cat No. ACN-1131N (Qty:01 No.)
104	Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : 100 mm inlet and 75 mm outlet: Sand Cast Iron S&S as per IS- 1729
105	Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 180x150 mm size P type With Sewer bricks conforming to IS : 4885
106	Supplying and fixing of CP Health Faucet of Jaquar make CAT NO.573 or equivalent make with 8mm dia and flexible tube wall hook etc., Complete.
107	Jaquar ALD-573 or equivalent with hook & flexible tube
108	Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.
109	75 mm dia pipe
110	110 mm dia pipe
111	Providing and fixing soil, waste and vent pipes :
112	100mm Sand cast iron S&S pipe as per IS: 1729
113	75mm Sand cast iron S&S pipe as per IS: 1729
114	Providing and filling the joints with spun yarn, cement slurry and cement mortar 1:2 ( 1 cement : 2 fine sand) in S.C.I./ C.I. Pipes :
115	75mm Sand cast iron S&S pipe as per IS: 1729
116	100mm Sand cast iron S&S pipe as per IS: 1729
117	Constructing brick masonry circular manhole 1.22 m internal dia at bottom and 0.56 m dia at top in cement mortar 1:4 (1 cement :4 coarse sand) inside cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement foundation concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design : 1.68 m deep with SFRC Cover and frame (heavy duty HD- 20 grade designation) 560 mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182 kg. fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12 mm thick cement plaster at the external surface shall be paid for separately) :With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
118	Supplying and fixing wash hand basin comprising of: Best quality of vitriouschina countertop wash basinof approved make or equivalent including 15mm powder coated piller cock,stop cock , waste coupling , bottle trap etc of approved make.
119	Providing and fixing wash basin of size 630x450 mmwith C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require.
120	Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS :2556, C.I. trap with outlet grating and other couplings in C.P. brass,including painting of fittings and cutting and making good the walls and floors wherever required Single half stall urinal with 5 litre P.V.C. automatic flushing cistern
121	Providing and fixing Stainless steel kitchen sink - with drain board 510x1040 mm bowl depth 250 mm with all necessary fittings. Make: Anupama/Nirali
122	Providing and fixing Stainless steel kitchen sink - without drain board 610x510 mm bowl depth 200 mm necessary fittings . Make: Anupama/Nirali
123	Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :
124	a) 15 mm nominal bore
125	Providing and fixing C.P. brasslong body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms
126	a) 15 mm nominal bore
127	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed work, including cutting chases and making good the walls etc.
128	a) 15 mm nominal dia Pipes
129	b) 20 mm nominal dia Pipes
130	c) 25 mm nominal dia Pipes
131	Supply, installation , testing and commissioning of shower unit with Wall Mixer 3-in-1 System withOverhead Shower Complete with 115mm Long Bend Pipe, Connecting Legs & Wall Flange including over head showerProviding and fixingin position best qualityof approved make 15mm CPBrass stop cock for geysers with necessaryscrews etc., Complete .
132	Providing and fixingin position best qualityof approved make 15mm CPBrass stop cock for geysers with necessaryscrews etc., Complete .
133	Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :
134	25 mm nominal bore
135	Supplying and fixing\"in position best qualityCPTowelrod ofapproved make and length 600mm long with a pair of brackets flanges fixed towall withnecessaryplug screws ,washers etc., complete .
136	Supplying and fixing\"in position best quality TowelRing Square ofapproved makewith minimum distances of 3mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms
137	Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.(@20 Kg per sqm of terrace area)
138	M&L forProvision/Errectionof Terrace roofing with double truss frames with 80x40x2mm, GP tubes 40x20x16 with purlins of size 40 x 40 x 16g or 50 x 25x 16 g.The Post shall be of size 70 mm round GI pipes with tie beams as per the site requirement.Suitable base plates and anchor bolts shall be provided without any extra cost. The complete structure will be applied one coat epoxy primer and two coats of synthetic enamel paint. The roof shall be covered with 0.40 mm galvalume sheet Jindal,JSW,SDS Patta Brand.
139	Rain water gutter shall be of Euro guard 8\" related connection drop fitting with GI clamps
140	Providing and fixing decorative wall paper of approved make, shade and design on wall (plain/ wood grain/ in glossy/ matt / suede finishing) with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS :2046 Type S including cost of adhesives, labour and transportation charges.
141	Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge
142	Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.
143	Providing & fixing White vitreous china water closet squatting pan (Indian type) along with \"S\" or \"P\" trap including dismantling of old WC seat and \"S\" or \"P\" trap at site complete with all operations including all necessary materials, labour and disposal of dismantled material i/c malba, all complete as per the direction of Engineer-in charge.
144	Supply and installation of 6mm thick Exterior grade F- Quality panels of standard size of one of the following: 1.3 x 2.8 m /1.854 x 2.8 m / 1.3 x 4.1 m / 1.854 x 4.1 m, with both side décor of FunderMax make or equivalent .The panels must be duromer high-pressure laminates (HPL) as per EN 438-6 type EDF with norm conformity as per EN 438-7 manufactured using NT Technology (Non-fading high performance acrylic polyurethane surface technology) conforming to norms with CE Mark. Panels are double hardened including acrylic polyurethane resin which is thermally cured under high pressure. The panel should have passed salt spray test for 24 hours, possess performance sustainability certificate for more than 25 years and proof of experience in handling similar type of work in India for more than 10 years. Material should be class B / class 1 complying with NBC 2016, ASTM E 84, BS 476 – 7 Installation of these panels must be done by MBE Rivets(with Fixed and Sliding Points) with minimum recommended Aluminum T section of 75x37x2 mm thick and L section 40x37x2.8mm thick held by Wall Bracket with Wind load and Dead load slot as per design, anchored by standard Hilti/Fischer or equivalent make anchor fasteners along with Thermal Separator. Installation of the HPL Panels will be done using Rear Ventilated Principles only which is ensured by providing gaps of 20 mm at top and bottom(for free flow of air behind the façade) for the façade and using the framework with no horizontal section for internal wall panelling.
145	Supply and installation of 6mm thick Exterior grade F- Quality panels of standard size of one of the following: 1.3 x 2.8 m /1.854 x 2.8 m / 1.3 x 4.1 m / 1.854 x 4.1 m, with both side décor of FunderMax make or equivalent .The panels must be duromer high-pressure laminates (HPL) as per EN 438-6 type EDF with norm conformity as per EN 438-7 manufactured using NT Technology (Non-fading high performance acrylic polyurethane surface technology) conforming to norms with CE Mark. Panels are double hardened including acrylic polyurethane resin which is thermally cured under high pressure. The panel should have passed salt spray test for 24 hours, possess performance sustainability certificate for more than 25 years and proof of experience in handling similar type of work in India for more than 10 years. Material should be class B / class 1 complying with NBC 2016, ASTM E 84, BS 476 – 7 Installation of these panels must be done by MBE Rivets(with Fixed and Sliding Points) with minimum recommended Aluminum T section of 75x37x2 mm thick and L section 40x37x2.8mm thick held by Wall Bracket with Wind load and Dead load slot as per design, anchored by standard Hilti/Fischer or equivalent make anchor fasteners along with Thermal Separator. Installation of the HPL Panels will be done using Rear Ventilated Principles only which is ensured by providing gaps of 20 mm at top and bottom(for free flow of air behind the façade) for the façade and using the framework with no horizontal section for External wall panelling.
146	Design supply & installation of suspended Spider Glazing system designed to withstand the wind pressure as per IS 875 (Part-III). The Suspended System held with Spider Fittings of SS-316 Grade Steel of approved manufacturer with glass panel having 12 mm thick clear toughened glass held together with SS- 316 Grade Stainless steel Spider & bolt assembly with laminated glass fins 21 mm thick. The Glass fins and glass panel assembly shall be connected to Slab/ beams by means of SS- 316 Grade stainless steel brackets & Anchor bolts and at the bottom using SS channel of 50x25x2mm using fastener & anchor bolts, non staining weather sealants of approved make, Teflon/ nylon bushes and separators to prevent bi-metallic contacts, all complete to perform as per specification and approved drawings. The complete system to be designed to accommodate thermal expansion & seismic movements etc. The joints between glass panels (6 to 8 mm) and gaps at the perimeter & in U channel of the assembly to be filled with non staining weather sealant, so as to make the entire system fully water proof & dust proof. The rate shall include all design, Engineering and shop drawing including approval from structural designer, labour, T&P, scaffolding, other incidental charges including wastage, enabling temporary services all fitting fixers nut bolts, washer, Buffer plates, fastener, anchors, SS channel laminated glass etc. all complete. For the purpose of payment, actual elevation area of Glazing including thickness of joints and the portion of Glass panel inside the SS channel shall be measured.
147	SCHEDULE OF CREDIT B/R
148	Aluminium/Gypsum partitions, doors, windows,fixed glazing and false ceiling
149	Doors and Windows of area 3.0 sqm and below
150	Doors and Windows of area beyond 3.0 sqm
151	GI Pipe 15 mm
152	GI Pipe 20 mm
153	GI Pipe 25 mm
154	GI Pipe 40 mm
155	Sanitary fittings like EWC,Flush tank & WHB
156	CP Bib cock, Stop cock, Angle cock
157	Wall mixer, WHB mixer
158	Kitchen sink
159	INTERNAL ELECTRIFICATION
160	Rewiring for Supply, fixinglight point / fan point,exhaust fan point call bell point, socket point with 1100 volt grade 1.5 sq.mmFRLS PVC insulated multistranded copper conductor single core cable as earth wire in Existing surface/recessed steel/PVC conduitwith modular switch, Modular plate,dismaltling as required, like- taking down Old unserviceable point wiring including switches,sockets, light fittings, GI boxes, GI Earth wire, phenolic laminated sheet, and other fittings/fixers including Ceiling Fans/Exhaust Fans and kept in safe custody and transported to department stores and to be issued to contractor under Scedule of credit,( PVC Conduit if required,Modular switches, sockets any type, Call Bell, Light fitings, Ceiling Fans, Exhaust Fans etc to be measured and paid separately) including cutting and making good the disturbed surfaces, matching with the existing surfaces, complete all as specified and as directed.
161	a) One Lightpoint controlled by one 6A Switch
162	b) One ceiling fan pointcontrolled by one 6A Switch andregulator.
163	c) One Exhaust fanpoint controlled by one 6A Switch
164	d) One bell point controlled by one bell push
165	e) One 6Amps socket controlled by one switch in same board.
166	f) One 6Amps socket controlled by one switch in Independent board.
167	Supply, fixing and Rewiring forOne Lightpoint controlled by Two Two way 6A switches, with 1100 volt grade1.5 sq.mmFRLS PVC insulated multiustranded copper conductor single core cable as earth wire in Existing surface/recessed steel/PVC conduit dismaltling as required, ike- taking down Old unserviceable point wiring including switches, GI boxes, GI Earth wire, phenolic laminated sheet, and other fittings/fixers and kept in safe custody and transported to department stores, cincluding cutting and making good the disturbed surfaces, matching with the existing surfaces omplete all as specified and as directed.
168	Supply drawing following sizes of FRLS PVC insilated copper conductor single core cable as earth wire (for 3x2.5 sq.mm single core cable Phase, Neutral and Earth wire connected to the earth dolly for Power pointin Existing surface recesses steelPVC conduit including dismantling like- taking down Old unserviceable One 16Amps switch and socket, GI boxes, GI Earth wire including sub main wiring from DB to Socket in Independent board,including cutting and making good the disturbed surfaces, matching with the existing surfaces complete all as specified and as directed.
169	Supply drawing following sizes of FRLS PVC insilated multistranded copper conductor single core cable 1100 volt grade (for 3x4 sq.mm single core cable, Phase, Neutral and Earth wire as earth wire connected to the earth dolly, Power point in Existing surface recesses steelPVC conduit including dismantling and including taking down Old unserviceable One 32 Amps Metal clad boxes, GI Box,GI Earth wire, socket and MCB including sub main wiring from DB to AC Socket in Independent board, complete all as specified and as directed.
170	Supplying and fixing for Existingof following sizes medium classPVC conduit along with accessories in surface/recess including cutting thewall, chases, pinning in, making good to facings where ever required and pointing in cement mortar 1:3 ration to ends or edges of landings, steps, cills, sun shades, shelves, lintels etc; and cutting chases for concealed conduit wiring, making good and painting as required etc, cutting not exceeding 10cm girthincluding cutting and making good the disturbed surfaces, matching with the existing surfacesComplete all as specified and directed.
171	a) 20 mm dia
172	b) 25 mm dia
173	Supply and fixing for Point Wiring for light point / fan point / exhaust fan point / call bell point with 1.5 Sq.mm FRLS PVC insulated multistranded copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI Box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc as required and including cutting and making good the disturbed surfaces, matching with the existing surfaces,complete all as specified and as directed.
174	One Lightpoint controlled by one 6A Switch
175	One ceiling fan pointcontrolled by one 6 A Switch and electronic fan regulator of 100W step type with concealed MS Fan hook box.
176	One Exhaust fanpoint controlled by one 6A Switch
177	One bell point controlled by one bell push
178	One 6Amps, 3/5Pin Socket outlet for Same/Dependent Board complete all as specified and asdirected.
179	One 6Amps, 3/5Pin Socket outlet for Independent board complete all as specified and asdirected.
180	Supply, Fixing and Point wiring for Twin control light point with 1100 volt grade1.5 sq.mm FRLF PVCinsulated multistranded copper conductor single core cable in surface ,\/ recessed medium class PVC conduit, Two two way modular switch ,modular plate,suitable GI box and conduit,Two two way modular switches, modular plate, suitable GI box earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. Connected to the earth dolly, as required, complete all as specified and as directed.
181	Supplyingang fixing Call Bell/ Buzzer suitable for single phase, 230 volts on wall/ surfaceas required, complete all as specified and as directed.
182	Supplying and fixing for Modular type Bell push switch piono 6Amp single phase one Way on the modular plate including necessary connection,complete all as specified and as directed.
183	Supply and fixing for Modular type switch piono 6Amp single phase one Way on the modular plate including necessary connection,complete all as specified and as directed.
184	Supply and fixing for Modular type switch piono 6Amp single phase Two Way on the modular plate including necessary connection,complete all as specified and as directed.
185	Supply and fiing for Modular type Socket outlet 6Amp 3/5 pin single phase on the modular plate including necessary connection,complete all as specified and as directed.
186	Supply and fixing modular Blanking plate on the existing modular plate and switch boxes excluding modular plate as required, complete all as specified and as directed.
187	Supply, Fixingand Wiring for circuit/ submain along with earth wirewith the following size 1100V grade PVC insulated multistrandFRLSCopper conductor wires inand including suitable size medium gauge PVC conduit concealed in wall / Ceiling including all accessories suchas junction boxes, bends, elbows including end terminated with suitable lugs etc. including cutting and making good the disturbed surfaces, matching with the existing surfaces complete all as specified and asdirected.
188	2 runs of 2.5 Sq.mm wires with 1 run of 2.5 Sq.mm wire in and including25 mm Dia PVC Conduit (For LightingCircuit).
189	2 runs of 2.5 Sq.mm wires with 1 run of 2.5 Sq.mm wire in existing PVCConduit (For lighting circuit).
190	4 runs of 6 Sq.mm wires with 2 runs of 6 Sq.mm wiresin and including 32mm dia PVC Conduit (For lighting Sub Mains).
191	4 runs of 6 Sq.mm wires with 2 runs of 6 Sq.mm wiresin existing PVC Conduit (For lighting circuit).
192	Supply and fixing and wiring for circuit/submain wiring alongwith eareh wire with the 4 run of 10 Sq.mm with 2 run of 6 sq.mm earth wire of FRLS PVC insulated copper conductor,single core cable in surface / recessed medium class Pvc conduit as requiredand including cutting and making good the disturbed surface match with the existing surface, complete all as specified and as directed. ( For TPN DB)
193	Supplying and fixing non rigid metallic PVC conduit 25 mm dia medium grade along with accessories in surface/recess including cutting chases, pinning in, making good to facings where ever required and pointing in cement mortar 1:3 ration to ends or edges of landings, steps, cills, sun shades, shelves, lintels etc; and cutting chases for concealed conduit wiring, making good and painting as required etc, cutting not exceeding 10cm girth. Complete all as specified and directed.
194	Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the exising surface/recessed steel/PVC conduit as required.
195	2 runs x 2.5 Sqmm and 1R x 2.5 Sqmm
196	4 runs x 2.5 Sqmm and 2R x 2.5 Sqmm
197	2 runs x 1.5 Sqmm and 1R x 1.5 Sqmm
198	Supplying and fixing suitable size G.I box with modular plate and cover in front or surface or in recess, including providing and fixing 3 pin 5/6A modular socket outlet and 5/6A modular switch, connection etc including cutting and making good the disturbed surfaces, matching with the existing surfaces, omplete all as specified and as directed.
199	Supplying and fixing following size / module G.I box alongwith modular base & cover plate for modular switches in recess etc as required .including cutting and making good the disturbed surfaces, matching with the existing surfaces ,complete all as specified and as directed.
200	8 Module (125 MM x 125MM)
201	6 Module (200 MM x 75MM)
202	3 Module (100 MM x 75MM)
203	Supply, Installation,Testing &Commissioning of thefollowing type LED light fixtures on wall/ Ceiling including all fixing accesssories such as leads, etc complete as required. The fixtures shall be complete with all prewired upto the terminal block. All fixtures shall besupplied with lamps. The Catalogue Numbers refers to Philips Make and taking down of the unservicebale fittings,complete all as specified and as directed.
204	a) 20 W Surface mounted LED 4 Feet LengthLuminaire (Philips : BN308C LED40S-6500 L120 PSU WH), omplete all as specified and as directed.
205	b) Twinglow 20-Watt + 20-Watt LED Up-Down batten tubelight (Yellow uplight relax mode and white downlight work mode) Aesthetic design, ambience of downlight & coverlight from tubelight (Philips : Twinglow), complete all as specified and as directed.
206	c) 1 x12 WSurface MountedLED Luminaire (PhilipsCat No : SM250C LED 12S-6500PSU WH), complete all as specified and as directed.
207	d) 36 WRecessMountedLEDLight Fixture (2\" x 2\" panel light) (PhilipsCat No :RC 380 B LED 40S-6500 G4L60W60 PSU OD), complete all as specified and as directed.
208	e) 12 W Recess mounted Down Light Fixture (PhilipsCat No DN195B LED20S-6500 PSU WH S2), complete all as specified and as directed.
209	f) 33 W Even Glow 120 LEDs/metre strip light (Each No 5 mtr Length)(Philips model No.582241), complete all as specified and as directed.
210	g) 33 W Constant voltage driver for LED flexible strip light, complete all as specified and as directed.
211	h) 36 W LED Outdoor type light fitting with bracket and accessories (Philips Cat No :BRP046 LED 36 CW MR S1 PSU GR), complete all as specified and as directed.
212	j) 5W Foot lamp with modular box and lamp holder (MK Cat no : W26530), complete all as specified and as directed.
213	k) 10 W Surface mounted LED 1 Feet LengthLuminaire (Mirror lamp), complete all as specified and as directed.
214	Supply, Installation, Testing and commissioning of 1200 mm sweepwhite colour Ceiling fan with standard down rod(600mm length down rod in false ceiling areas) andall accessories Electrical connections but excluding supply of Fan regulator as required etc. ( BEE Labelled 5 Star Energy Saving Fan ).Taking down of the unservicebale fan, complete all as specified and as directed. Includig fan regulator
215	Supply, Installation, Testing andcommissioning for305 mm sweep Exhaust fans (Heavy duty) with Metallic blades and MS gravity louversincluding all accessories / Installation materials required and taking down of the unserviceble exhaust fan, complete all as specified and as directed.
216	Supply, Installation, Testing andcommissioning for305 mm sweep Exhaust fans with Metallic blades and MS gravity louversincluding all accessories / Installation materials required and taking down of the unserviceble exhaust fan, complete all as specified and as directed.
217	Supplying and fixing for Distribution Board Double door TPN 4 Way 415 V0ltsVertical type, double door three pole and neutral, sheet steel, MCB distribution board, on surface/ recess, complete with tinned copper bus bar,neutral bus bar, earth bar, din bar, interconnections, powderpainted including earthing, Blanking plate etc. as required. (MCB/RCCB/Isolator to be measured and paid separately) including taking down of the unserviceble distribution board, complete all as specified and as directed.( For G.F, F.F and S.F)
218	Supplying and fixing for Distribution Board Double Door SPN 12 Way 230 V0ltshorizontal type, double door Single pole and neutral, sheet steel, MCB distribution board,on surface/ recess, complete with tinned copper bus bar,neutral bus bar, earth bar, din bar, interconnections, powderpainted including earthing, Blanking plate etc. as required.MCBTo be measured and paid separately, including taking down of the unserviceble distribution board, complete all asspecified and as directed.( 02 Nos each Floor).
219	Supplying and fixing for Distribution Board Double Door SPN 6 Way 230 V0ltshorizontal type double door Single pole and neutral, sheet steel, MCB distribution board,on surface/ recess, complete with tinned copper bus bar,neutral bus bar, earth bar, din bar, interconnections, powderpainted including earthing, Blanking plate etc. as required.MCBTo be measured and paid separately, including taking down of the unserviceble distribution board, complete all as specified and as directed.( 01 Nos each Floor for security light).
220	Supplying and fixing for MCB TPN 415Volts, 10 KA 63 Amps capacity of rating‘C’ Curveminiature circuit breaker suitable for inductive loadpoles in thecomplete with connections ,testing and commissioning etc complete, complete allas specified and as directed.
221	Supplying and fixing for MCB SPN 230 Volts, 10 KA 40 Amps capacity of rating‘C’ Curveminiature circuit breaker suitable for inductive loadpoles in thecomplete with connections ,testing and commissioning etc complete, complete allas specified and as directed.
222	Supplying and fixing for MCB SPN 230 Volts, 10 KA 32 Amps capacity of rating‘C’ Curveminiature circuit breaker suitable for inductive loadpoles in thecomplete with connections, testing and commissioning etc complete, complete allas specified and as directed.
223	Supplying and fixingof 6A to 32A rating 230 Volt, 10KA, ‘C’ Curveminiature circuit breaker single pole suitable for inductive load of suitable capacity and including all necessaryconnections ,testing and commissioning etc complete all as specified and as directed.
224	Supply and fixing single pole blanking plate in the existing MCB DB complete etc. As required, complete all as spoecified ands as directed.
225	SCHEDULE OF CREDIT E/M
226	Taking down u/s point wiring of any description with all fittings, fixtures
227	Taking down u/s sub main wiring of any size
228	Taking down u/s light fittings of any type
229	Taking down u/s cel
230	Taking down u/s wiring of any description with all fittings & fixture
231	Taking down u/s wiring of any description with all fittings & fixture
232	Taking down u/s wiring of any description with all fittings & fixture
233	Taking down u/s wiring of any description with all fittings & fixture
234	Taking down u/s wiring of any description with all fittings & fixture
235	Taking down u/s wiring of any description with all fittings & fixture
236	POWER WIRING
237	Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/lsolator) (a) 6 way (4 + 18), Double door
238	Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. (a) 63A
239	Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, \"C\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. (a) Single Pole
240	MODULAR POWERSOCKETS
241	Supply, erection, testing and commissioning of the following switchsockets with anodised G.I. Box,front plate and fixing screws etc .
242	6/16 Amps, 5-pin (250 Volts) single phase modular type socket controlled by 16 Amps SP Switch. Water& CPOH is not considered
243	Supply and fixing of factory made 20A, 1Ph Metalclad socket with plugtop &20A SPMCB in MS box including all fixing accessories Rate is inclusive of wat er charges + CPOH
244	Supply and installations of 25 Liters capacity storage type geysers operating on single phase, 220V, 50 Hz power supply including pipe connections for inlet and outlet etc., complete all as specified.
245	WIRING
246	Supply and Wiring with the following size 1100V grade PVC insulated multistrand, FRLS Copper conductor wires in and includingsuitable size heavy gauge PVC conduit concealed in wall / Ceiling including all accessories such as junction boxes, bends, elbows including end terminated with suitable lugs.
247	a) 2 runs of 4 Sq.mm wires with 1 run of 4 Sq.mm wireinand including 25mm diaPVC Conduit(For 16A Sockets).
248	b) 2 runs of 6 Sq.mm wires with 1 run of 6 Sq.mm wireinand including 25mm diaPVC Conduit(For AC Sockets).
249	c) 4 runs of 10 Sq.mm wires with 2 runs of 6 Sq.mm wireinand including 25mm diaPVC Conduit
250	Providing and fixing of maintenance free earthing which consists of 40mm Dia, standrad length (as per Equipment Supplier) electrode capsule, filled with earth enhancing compound,sealed at both ends and brazed lead for connection at one end suitable for direct installation at site at a depth of 2.5 mtr.Earth enhancingcompound upto a depth of 2.0 mtr around the electrode capsule and also wih brick chamber and cast Iron cover etc complete including excavation in all types of soil.
251	Supply and laying of following size strips including all necessary inter connections with earth station and equipments.
252	a) 50 X 5 mm Hot dip GI strip
253	Supplying and laying 25 mm X 5 mm G.l. strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.l. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.l. nut bolt & spring washer spaced at 50mm)
254	Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required.
255	Providing, laying, testing & commissioning of \"B\" class heavy duty G.I. pipe conforming to IS 1239 including welding, fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : (a) 50mm Dia
256	TELEPHONE AND LAN
257	Supply and laying of 25mm dia, heavy gaugePVC. conduit concealed in wall/ ceiling/ floor including all accessories such as junction boxes, conduit bends, etc., complete as required for Telephone etc.,
258	Supply and fixing of Telephone socket outlet (RJ11) with anodised GI box with front plate and fixing screws on the existing modular olate and switch box including connectios but excluding modular plate etc. As required, complete all as specified and as directed..
259	Supply and fixing of TV outletwith anodised GI box with front plate and fixing screws.
260	Supply and laying of 2pair 0.5mm dia PVC insulated Copper conductor Telephone wireconforming to DOT Specifications in already laid PVC Conduit including necessary interconnections.
261	Supplying and drawing co-axial TV Cable RG-6 grade, 0.7mm soild copper conductor PE insulated, shielded with fine tinned copper-braid and protected with PVC sheath in the existing surface / recessed steel / PVC conduit as required.
262	Supply and installation of10 pair Krone connectors inMS junction box complete as required.
263	Supply, laying, jointing GI pipes of medium quality including specials of approved make fixed to wall/to the required lengths, threading jointing chasing the walls and floor, making holes, clamping of clamps and making good the same, necessary excavation, etc., complete as specifed and directed.50mm Dia
264	PASSANGER ELEVATOR
265	Supply,Installation, Testing & Commissioning of SS Cabin Finish Passenger Auto Lift for 06 Passengersfor G+2 height( about 10.10.8 Mtr i.eupto bottm of second floor)of Gearless Machine Roomless of OTIS,Kone, Omega or Equivalent make havingthe following specifications:- (i)LOAD & SPEED :- About 408 Kg @ 1 M / Sec.(ii) CONTROL : Micro Processor Based V.V.V. F. ARD System.(iii)POWER SUPPLY:-415 Volts, 3 Phase, 50 Cycles, Alternating Current.(iv) TRAVEL :-G + 2 about 6 meters.(v)STOP & OPENING :- 3 Stops, 3 Openings (All openings on the same side).(vi)MACHINE :- Directly placed above hoist way.(vii) OPERATION :- Collective selective with ON OFF Switch.(viii) HOIST WAY REQUIRED:-1700 mm wide x 1600 mm deep available.(ix) CAR ENCLOSURE :- SS Cabin Finish.(x)CAR ENTRANCE:-Protected by Telecopic Hair Line finish with infrared curtain(xi)HOUSE WAY ENTRANCE:-Protected by Telescopic SS Hair Line Clear opening about 700 mm wide x 2000 mm high.(xii) DOOR OPERATION :-Power OperatedAutomatic.(xiii)BRAKE :-Electromagnetic type which opens on energization with 24 / 48 VDC voltage and close by means.(xiv)DRIVING MOTOR:PMSM (Permanent mahnet Synchtronus Motor. (xv)ELECTRICAL SAFETY DEVICE:-(a) Mains 3 phase limit switch to protect against over travel.(b) Single phasing preventor with a protection against phase sequence reversal.(c) Full proof gate locks for landing doors
266	(d) Car gate switch.(e) Over speed Governor.(f)Over speed safety device.(xvi)SIGNALS:-In Car -Battery operated Emergency Light, Alarm, Digital floor, Indication, Push Button for each floor.On / Off Switch Fan Switch.(xvii)DRIVING ROPES:-Ropes with factor of safety 12 or above.(xviii)CAR VENTILATION:-With automatic ON / OFF Fan.(xix)CAR LIGHTING :-LED lighting.(xx)LEVELLING ACCURACY:Max.As per article 10 of IS: 14665 : 2000 . Min +/12mm. (xxi)DRIVE :-Fuji or Equivalent.(xxii)STAINLESS STEEL SHEETS:-SAIL / JINDAL / IMPORTED.(xxiii) MILD STEEL SHEET :- TATA / ESSAR / IMPORTED. (i)ELEVATOR FABRICATED SHAFT:- MS Structure for Lift (G+2) of size 1700 x 1400 mm, PIT – 1500 mm, OH – 4600mm.MS Square Pipe of size 100 x 100 x 6mm, ISMC – 150 x 75 mm, Cross bracing of MS Angle of size 50 x 50 x6mm & misc steel ( Approx weight 2560 Kg).(ii)SCAFFOLDING:- Bamboo external scafolding for farication and cladding.Internal scaffolding for lift installation (Approx.3800 sq ft)(iii)ELEVATOR CIVIL WORK:-RCCPITof size 1700 x 1400 x 1500 mm.Parapet Breaking and finishing(01 Job).
267	(iv) ELECTRICAL SHAFT:-Three Phase Armoured 4 core and single phae, 3 core / 2.5 Sq.mm Armoured Cables with earthing pits & swith gears (MCB / ELCB)(01 Job)(v) ACP CLADDING:-STD make aluminium composite Panels (Metallic & Solid Finishes) of 3 mm / 0.5 thickness in 2 x 1 inchAluminium pipes and framing grid of 4 x 2 ft.Rear two sides, front wall and lobby connect inner & outer and Top Canopy(Approx 1260 sq. ft)(vi)GLASS CLADDING :-Plain 8 mm toughened glass in stud fixing (Approx. 150 sq. ft).Complete all as secified and shownon drawing attached and as directed by Enginer-in-Charge. Note:-The structure forlift is to be provided at existing Building.Contactors are requested to visit the site before quoting.The rates quoted areinclusive ofmaking goodto demolishedportion if any as per the site requirement. Note:-The lift is to be provided at existing Building.Contactors are requested to visit the site before quoting.The rates quoted areinclusive ofminor extrasif any as per the site requirement.Provision of Civil Works for Electrical Shaft as per the following Specifications:-
268	WATER COOLERS
269	Supply installation of 40/80 lTRS Capacity Water Coolers with RO water Purifier ,including necessary fittings all as per manufacturers specifications etc., complete
270	LIGHTNING PROTECTION
271	Providing and fixing of maintenance free earthing which consists of 40mm Dia, standrad length (as per Equipment Supplier) electrode capsule, filled with earth enhancing compound, sealed at both ends and brazed lead for connection at one end suitable for direct installation at site at a depth of 2.5 mtr. Earth enhancingcompound upto a depth of 2.0 mtr around the electrode capsule and also wih brick chamber and cast Iron cover etc complete including excavation in all types of soil.
272	Supplying,laying and fixing 32mmx6mm GI strip from earth electrodeat 0.50 metre below ground as strip earth electrode, including connection/ terminatiing with GI nuts, bolts, spring, washers etc. As required.( Jointing shall be done by overlapping and with 2 sets of GI nuts bolts and spring washers spaced 50mm, complete all as specified and as directed.
273	Providing and fixing testing jointing, made of 20mm x 3mm thick GI tape on parapet or surface of wall for lightning conductor complete as required for horizontalrun, complete all as specified and as directed.
274	Providing and fixing testing jointing, made of 20mm x 3mm thick GI tape on parapet or surface of wall for lightning conductor complete as required for vertical run, complete all as specified and as directed.
275	Providing and fixing of lightning conductor finial made of 25mm doa 300mm long GI tube having single prong at top, with 85mm dia 6mm thick base plate including holes etc. Complete as required, complete all as specified and as directed.
276	Jointing GI tape with another GI tape , base of the finial or any other metalic object by riveting/nuts and bolting/ sweating and soldering etc. As required, complete all as specified and as directed.
277	EXTERNAL ELECTRIFICATION
278	Laying of one number PVC insulated and PVC sheathed /XLPE power cable of 1.1 KV grade of size 95 Sqmm directed in ground including excavation, sand cushioning, protective covering and refiing the trench etc, as required, complete as as specified and as directed.( Cable shall be issued and measured separately as item No-2 below)
279	Supply only Cable XLPE 185 Sqmm 4 core 1.1 volt grade excavation and other connting work measured and paid separatelt item ano-1 above, complete al as specified as directed.
280	Supply only Cable XLPE 16 Sqmm 4 core 1.1 volt grade excavation and other connting work measured and paid separatelt item ano-1 above, complete al as specified as directed.
281	Supply and fixing indoor type LT panel board 02 incoming (01 for main 200 Amps capacity 4 pole and 01 for change over switch 250 Amps capacity 4 pole) 06 Nos out going 63 Amps MCB TPN and 05 Nos out going for 32 Amps SPN 01 No for RCCB 40 Amps capacity.
282	EXTERNAL SERVICES
283	(a) COMPOUND WALL
284	Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.
285	Upto 1.50 Mtr
286	Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.
287	Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources).
288	Providing and laying cement concrete 1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size ) in string and lacing courses,coping , bed blocks ,anchor blocks , and window cills and like including necessary shuttering and centring at all Levels and locations etc., complete all as shown in drawings and as directed .
289	Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with : Cement mortar 1:6 (1 cement : 6 coarse sand)
290	Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in Cement mortar 1:6 (1 cement : 6 coarse sand)
291	15 mm cement plaster on the rough side of single or half brick wall of mix1:6 (1 cement: 6 fine sand)
292	12mm thick plastering Over coping in CM 1:6 (1 cement: 6 fine sand)
293	Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm
294	(PART-II) ADDITIONS/ALTERATIONS ANDSPECIAL REPAIRS TO BLDG NO D1, D2 AND D-20AT UARF KULAMAVU
295	CIVIL WORKS
296	Dismantling Asbestoes sheet roofing including ridges, hips, valleys and gutters etc., and stacking the material within 50 metres lead of:
297	Dismantling wood work sectional area 40 square centimeters abovein frames, trusses, purlins and rafters up to 10metres span and 5 metres height including stacking the material within 50 metres lead :
298	Dismantling doors,windows and clerestory windows (steel or wood) shuter including chowkhats ,architrave ,holdfast etc, complete and stacking within 50 meters lead
299	Dismantling tile work in floors and dados laid in cement mortar including stacking materials within 50 meters lead : for thickness of tiles 10mm to 25 mm
300	Removing the all kinds of sanitary fittings like EWC, Urinals,Wash hand basins including stacking of items within 50 meters lead as per direction of Engineer-in-Charge
301	Demolishing cement concrete manually/by mechanical means including disposal of material within 50 meters lead as per the direction of Engineer-in-Charge
302	Providing and laying plinth protection with 50 mm thick PCC 1:3:6 (1 cement, 3 coarse sand and 6 graded stone aggregate 20 mm nominal size) over 75 mm thick brickballast of 40 mm nominal size well rammed, consolidated and grouted with fine sand including finishing the top smooth with additional cemet mortar 1:4 a floating coat of neat cement finish and filling the construction joints with sand and bitumen etc; complete all as specified and directed.
303	Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.
304	18 mm thick cement plastering on external surfaces of brick or concrete surfaces in two layers of 6 mm thick cement mortar 1:3 ( 1 cement 3 fine sand ) top coat mixed with integral water proofing compound over a base coat 12 mm thick cement mortar 1:5 (1 cement : 5 coarse sand), finished sand face etc; complete at all levels and locations.
305	15 mm thick plastering in cement mortar 1:6 (1 cement: 6 fine sand) on internal surfaces of walls finished smooth and even etc., complete at all levels and locations.
306	Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre of approved manufacturer, of required shade and colour complete,as per manufacturers specification,two or more coats over and including water thinnable cement primer having VOC content less than 50 gms/litre of approved brand and manufacture on wall surface.
307	Providing and applying cement based putty of average thickness 1mm, of approved brand and manufacturer, over plastered surface to prepare the surface even and smooth complete
308	Providing (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) Finishing walls with Acrylic Smooth exterior paint of required shade and colour all as directed
309	Providing and applying two coats of synthetic enamel paint of approved brand and shade over a coat of primer including preparation of surface and applying approved brand putty on following surfaces at all levels and locations etc complete.
310	Supplying and laying approved make and shade anti skid ceramic tile of thickness upto 6mm and size 300 x 300mm for flooring laid on 20 mm thick cement mortar 1:4 jointing with grey cement slurry @ 3.30 kg/Sqm, including curing and pointings with white cement and matching pigment etc., Complete all as directed by the Engineer-in-Charge
311	Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS 15622 (thickness to be specified by the manufacturer), of approved make in all colours shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.30kgs per sqm , including pointing in white cement with mixed pigment of matching shade complete
312	Providing and laying Vitrified tiles in floor of 1200 x 600 mmsizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.
313	Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant and fixed in position with M.S hold fast/ lugs/ SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. Frame size 65 x 125 mm
314	Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately)
315	Providing and fixing2nd class teak wood 30 mm thick glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes (weight not less than 10 kg per sqm) fixing with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws.
316	Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross-section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminate shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame.
317	Providing and fixing 30 mm thick Fiber glass Reinforced Plastic (F.R.P.) flush door shutter in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF)/Polystyrene foam to be used as filler material throughout the hollow panel, casted monolithically with testing parameters of F.R.P. laminate conforming to table - 3 of IS: 14856, complete as per direction of Engineer-in-charge.
318	Providing and fixing of sliding UPVC window with Three track three panels sliding window with fly proof SS wire mesh (Two nos. glazed & one no. wire mesh panels) made of (small series) frame 92 x 44 mm & sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area of window upto 1.75 sqm).the colour of the profile shall be of natural (white ) colour. The profiles used for the outer frame, shutter and mullions shall be reinforced with 1.2mm galvanized iron steel. Profile of frame & sash shall be mitred cut and fusion welded at all corners, includingdrilling of holes for fixing hardware\"s and drainage of water etc.After fixing frame the gap between frame and adjacent finishedwall shall be filled with weather proof silicon sealent over backerrod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge.
319	Providing and fixing factory made uPVC white colour fixed glazed ventilators comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), , uPVC extruded glazing beads ofappropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware\"s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge.(Using R1 series with frame Height upto 0.90 m)
320	Providing and fixing the following hardware fittings of approved make.
321	ISI marked oxidised MS pressed butt hinges with necessary screws etc., complete.
322	i) 100x58x1.9 mm
323	ii) 125x65x2.12mm
324	Aluminium handles, powder coated, ISI marked to required colour or shade with necessary screws etc., complete. - 125 mm
325	Powder coated ISI marked tower boltto required colour or shade with necessary screws etc., complete.for following sizes.
326	i) 200x10mm
327	ii) 150x10mm
328	d) Aluminium hanging floor door stopper ISI marked powder coated to required colour or shade with necessary screws etc., complete.
329	i) Twin rubber stopper
330	e) Providing & fixing Aldrop 300mm long with 16mm dia rod, required colour or shade with necessary screws etc., complete
331	f) Brass CP mortice lock six levers handles of Godrej / Dorset or equivalent make with necessary screws etc., complete for single door.
332	g) Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm) with double speed adjustment with necessary accessories and screws etc. complete.
333	Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre,GI Metal Ceiling Lay in perforated Tegular edge global white color tiles of size 595x595 mm and 0.5 mm thick with 8 mm drop; made of GI sheet having galvanizing of 100 gms/sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holes and having NRC (Noise Reduction Coefficient ) of 0.5, electro statically polyester powder coated of thickness60 microns (minimum), including factory painted after bending and perforation and backed with a black Glass fiber acoustical fleece.
334	Providing and fixing vitreous china dual purpose closet suitable for use as squatting pan or European type water closet (Anglo Indian W.C pan) with seat & lid fixed with C.P. brass hinges and rubber buffers, 10 litre low level flushing cistern with fitting and brackets, 40 mm flush bend, 20 mm over flow pipe, with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required: White vitreous china dual purpose WC pan with white solid plastic seat and lid with white vitreous china flushing cistern and C.P. flush bend.
335	Supplying and fixing in position best quality & approved make C P toilet paper roll holderwith necessary C Pbrass screws and washers fixed to walletc.,complete all as specified and directed.
336	Supplying & fixing in position best quality & approved make C Psoap container necessary including C P screws and washers fixed to wall etc., complete all as specified and directed.
337	Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : 100 mm inlet and 100 mm outlet Sand cast iron S&S as per IS: 3989.
338	Supplying and fixing of CP Health faucet ofparryware or equivalent make with 8mm dia and flexible tube wall hook, and angular stop cocketc., complete.
339	Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:
340	Supply, installation , testing and commissioning of shower unit with Wall Mixer 3-in-1 System with Provisionfor both Hand Shower and Overhead Shower Complete with 115mm Long Bend Pipe, Connecting Legs & Wall Flange including over head shower and hand shower.
341	Providing and fixing in position best quality of approved make 15mm CP brass stop cock for geyserswith necessary screws etc.complete.
342	Supplying and fixing in position best quality and approved make heavy quality screws down gun metal gate valves with hand wheel of the following sizes fixed to service lines including testing, making good the leakages, if any etc.,
343	a)25mm
344	Supplying and fixing in position best qualityCPtowel rod of length 600mm long with a pair of brackets flanges fixed to wall with necessary plugs screws , washers etc., complete.
345	Providing and fixing Towel Ring Square of JaguarAKP-35721P215 mm long, 200 mm wide with minimum distances of 3mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms
346	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc.
347	a)15mm.
348	b)20mm
349	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.
350	a)20mm
351	b)25mm
352	Supplying, laying, jointing, testing and commissioning; uPVC(SWR)pipe (Type-B) as per IS : 13592/1992 including specials of best quality and approved make fixed to wall/floor including chasing, cutting, making the hole in walls/floors, cutting the pipes to the required size of length jointing the pipes and specials with suitable resin and testing etc.,complete all as specified and directed. (Specials at junctions must have access doors wherever required.)
353	a) 100mm dia
354	Supply and fabrication and installation of UPVC Profile roofing with the following speicifications Frame works and beam with 80x40x16g GP tubes and 40x20x16g or as per the site requirement.Purlins with 40 x 20x 16g GP tubes, suitable base plates and anchor bolts, rafter spacing 110cm c/c, purlin spacing as per the roof tile and applying one coat of expxy primer and second coat with two coats of synthetic enamel paint on steel items including installation of UPVC tile profiled/Trafford roofing sheet, Ridges,and other fittings, SDS as selected and Euroguard rain water gutter, GI clamp and all necessary fittings, Ridge hips, Border valley,Drip,straight flashing Aluminium 0.46 mm thick all as per the direction of Engineer-in-Charge
355	Providing and fixing brass curtain rods of 25 mm diameter wall thickness 1.25 mm with two brackets fixed with brass screws and wooden plugs etc; wherever necessary complete
356	Providing and fixing best quality pillar cock brass CP of grade SS 304of approved make and design including fittigs and fixtures complete
357	Cement concrete pavement with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete.For D1 & D2 Approach path way
358	Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti- termite treatment (excluding the cost of chemical emulsion) : Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration.
359	Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor :
360	1:2:4 (1 cement : 2 coarse sand(zone-III) including manufactured sand derived from Recycled concrete aggregate (RCA) up to 25% : 4 graded stone aggregate 20 mm nominal size including Recycled Concrete Aggregate (RCA) upto 25% ) for drain
361	Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concreteas in drain
362	Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab of all colour and texture except Black, Cherry/Ruby Red
363	Providing and laying80 mm thick C.C paver block of M-30 grade with approved colour and design and pattern factory made chamfered edge, cement concretepaver block in footpath, parks, lawns,drive ways, ligh trafic parking etc, of required strength and, thickness & size/shapemade by table vitratory method using PU mould laid in required colour and pattern over 50 mm thick compacted bed of sand compacting and proper embedding/laying of inter locking paver blocking paver block into the sand bedding layer through vibrator compaction by using plate vibratorfilling joints with sand and cutting of paver block as required size and pattern finishing and sweeping extra sand complete all as specified and directed by Engr-in-Charge
364	Supply and fixing fancy type Kitchen sink tap swan neck tap 15 mm bore chromium plated parryware
365	Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :Kitchen sink with drain board 510x1040 mm bowl depth 250 mm.
366	Providing and fixing fly proofgalvanized M.S. wire gauge to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm With second class teak wood beading 62X19 mmall complete.
367	Providing and fixing mirror of superior glass (of approved quality) and of required shape and size (Oval shape 450x350 mm) (outer dimensions)with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :
368	Dismantling dressed stone work ashlar face stone work, marble work or precast concrete work manually/ by mechanical means including stacking of serviceable and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge :
369	Encasing rolled steel section in grillages with cement concrete 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III)derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources ) including centering and shuttering but, excluding cost of expanded metal and hangers.
370	Extra for providing and fixing expanded metal mesh of size 20x60 mm and strands 3.25 mm wide 1.6 mm thick weighing 3.64 kg per sqm for encasing of rolled steel sections in beams, columns and grillages, excluding cost of hangers.
371	Excavation work in any type of soil by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soils as directed, within a lead of 50m.
372	Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.
373	1:4:8 (1 Cement : 4 manufactured sand derived from Recycled Concrete Aggregate (RCA) : 8 graded stone aggregate 40 mm nominal size Recycled Aggregate (RA)).
374	Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.
375	Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.
376	1:1½:3 (1 Cement: 1½ coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).
377	Centering and shuttering including strutting, propping etc. and removal of form work for : Foundations, footings, bases for columns.
378	Centering and shuttering including strutting, propping etc. and removal of form work for Columns, piers, abutments, pillars, posts and struts.
379	Providing and applying two coats of synthetic enamel paint of approved brand and shade over a coat of primer including preparation of surface and applying approved brand putty on following surfaces at all levels and locations etc complete.
380	Disconnecting damaged overhead/terrace PVC water storage tank of any size from water supply line and removing from the terrace including shifting at ground level as per direction of Engineer-in- charge.
381	Providing and placing on terrace (at all floor levels) polyethylene water storage of capacity 1000 ltrstank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.
382	Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50m outside the periphery of the area cleared.
383	Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.
384	Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand)
385	Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with : Cement mortar 1:6 (1 cement : 6 coarse sand)
386	Coursed rubble masonry with hard stone (first sort) in superstructure above plinth level and upto floor five level in cement mortar (1:6)
387	Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing:
388	1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)
389	Providing and fixing decorative wall paper of approved make, shade and design on wall (plain/ wood grain/ in glossy/ matt / suede finishing) with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS :2046 Type S including cost of adhesives, labour and transportation charges.
390	Design supply & installation of suspended Spider Glazing system designed to withstand the wind pressure as per IS 875 (Part-III). The Suspended System held with Spider Fittings of SS-316 Grade Steel of approved manufacturer with glass panel having 12 mm thick clear toughened glass held together with SS- 316 Grade Stainless steel Spider & bolt assembly with laminated glass fins 21 mm thick. The Glass fins and glass panel assembly shall be connected to Slab/ beams by means of SS- 316 Grade stainless steel brackets & Anchor bolts and at the bottom using SS channel of 50x25x2mm using fastener & anchor bolts, non staining weather sealants of approved make, Teflon/ nylon bushes and separators to prevent bi-metallic contacts, all complete to perform as per specification and approved drawings. The complete system to be designed to accommodate thermal expansion & seismic movements etc. The joints between glass panels (6 to 8 mm) and gaps at the perimeter & in U channel of the assembly to be filled with non staining weather sealant, so as to make the entire system fully water proof & dust proof. The rate shall include all design, Engineering and shop drawing including approval from structural designer, labour, T&P, scaffolding, other incidental charges including wastage, enabling temporary services all fitting fixers nut bolts, washer, Buffer plates, fastener, anchors, SS channel laminated glass etc. all complete. For the purpose of payment, actual elevation area of Glazing including thickness of joints and the portion of Glass panel inside the SS channel shall be measured.
391	SCHEDULE OF CREDIT (B/R)
392	Unservicable doors and windows area not exceeding 3.0 sqm each including chowkhats/frame
393	Dismantling tile work in floors and dados laid in cement mortar including stacking materials within 50 meters lead : for thickness of tiles 10mm to 25 mm
394	Removing the all kinds of sanitary fittings like EWC, Urinals,Wash hand basins, towel rail, soap dish, health faucet,pillar tap stop cock, bib taps, wall mixer, shower etc including stacking of items within 50 meters lead as per direction of Engineer-in-Charge
395	Unservicable water storage tanks of any description and any capacity
396	Unservicable GI pipes of any description
397	Unservicable AC sheets of any description
398	Unservicable wooden truss and timber scantling
399	E/M WORKS
400	Rewiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable and 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable as earth wire in existing surface/recessed steel/PVC conduit including dismantling as required.
401	Group C
402	Rewiring for twin control light point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable and 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable as earth wire in existing surface/ recessed steel/PVC conduit including dismantling as required.
403	Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable etc. as required
404	Group C
405	Wiring for twin control light point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable etc. as required.
406	Supply, Installation, Testing and Commissioning of ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. metal Aluminum alloy) blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, steel/Al body Power Factor not less than 0.9, Service Value (CM/M/W) minimum as below, 350 RPM (tolerance as per IS : 374-2019), THD (Total Harmonic Distortion) less than 10%, suitable for operation with regulator for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Ceiling Fan compliant to IS 374:2019 fan Supply, earthing etc. complete as req
407	1200mm, service value ≥ 6.0 CM/Min/Watt, air delivery 210 CM/Min (Minimum)
408	Supply of 305 mm sweep Exhaust fans with Metallic blades and MS gravity louversincluding all accessories / Installation materials required
409	Installation, Testing and Commissioning of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required upto 450 mm sweep.
410	Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.
411	Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)
412	4 way (4 + 12), Double door
413	Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.
414	40A
415	Supplying and fixingof 6A to 32A rating 230 Volt, 10KA, ‘C’ Curveminiature circuit breaker single pole suitable for inductive load of suitable capacity and including all necessaryconnections ,testing and commissioning etc complete all as specified and as directed.
416	34 W Surface mounted LED 4 Feet LengthLuminaire (Philips : BN308C LED40S-6500 L120 PSU WH), omplete all as specified and as directed.
417	Twinglow 20-Watt + 20-Watt LED Up-Down batten tubelight (Yellow uplight relax mode and white downlight work mode) Aesthetic design, ambience of downlight & coverlight from tubelight (Philips : Twinglow), complete all as specified and as directed.
418	1 x12 WSurface MountedLED Luminaire (PhilipsCat No : SM250C LED 12S-6500PSU WH), complete all as specified and as directed.
419	20 W Recess mounted Down Light Fixture (PhilipsCat No DN296 20S-6500PSU WH ), complete all as specified and as directed.
420	33 W Even Glow 120 LEDs/metre strip light (Each No 5 mtr Length)(Philips model No.582241), complete all as specified and as directed.
421	5W Foot lamp with modular box and lamp holder (MK Cat no : W26530), complete all as specified and as directed.
422	Supplying and fixing call bell/ buzzer suitable for single phase, 230 V, complete as required.
423	Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc. as required.
424	a) 1 or 2 Module (75mmX75mm)
425	b) 3 Module (100mmX75mm)
426	c) 4 Module (125mmX75mm)
427	d) 6 Module (200mmX75mm)
428	e) 8 Module (125mmX125mm
429	f) 12 Module (200mmX150mm)
430	Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.
431	a) 5/6 A switch
432	b) 2 way 5/6 A switch
433	c) 15/16 A switch
434	d) 3 pin 5/6 A socket outlet
435	e) 6 pin 15/16 A socket outlet
436	f) Telephone socket outlet
437	g) TV antenna socket outlet
438	h) Bell push
439	Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS/HFFR PVC insulated copper conductor, single core cable in surface/recessed medium class PVC conduit as required
440	a) 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire
441	b) 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire
442	c) 2 X 4 sq. mm + 1 X 4 sq. mm earth wire
443	d) 4 X 6 sq. mm + 2 X 6 sq. mm earth wire
444	Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.
445	a) 20mm
446	b) 25mm
447	c) 32mm
448	Supplying and drawing 2 pair 0.5 mm dia FRLS/HFFR PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required
449	Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.
450	Supply and installation of10 pair Krone connectors inMS junction box complete as required.
451	Supplying & fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, \"C\" curve including connections, painting etc. as required.
452	FURNITURE
453	Designer TV Unit of size 1500 x 1950 x 400 made out of 19 mm thick commercial board and covered with 4 mm thick leak venner having two drawer ride on telescopic sliding channel, back with 6 mm thick commercial ply all edges covered with teak wood finish with melamine polish including of necessary hardware and fitting etc all complete.
454	Cupboard cum dressing unit of 600 mm deep with 4 Nos. Openable shutters, two vertical dividers and two shelves made out of 18 mm ply wood with 3.6 mm thick teak veneer, all exposed edges to have teak wood lipping with melamine polish and limination to internal surfaces etc; all complete as per directions of engineer-in-charge. (Openable shutters and Hardware shall include brass tower bolts, 100 mm long ‘C’ type brass / powder coated handles, Magnetic catchers and looks will be paid separately)
455	Providing and fixing 300 mm deep, 600 mm high storage units in pantry with openable shutters and one shelf inside all made with 18 mm thick commercial plywood with approved laminate for top, sides, bottom and for shutters and providing 12 mm thick commercial plywood for back, 20x4 mm teakwood beading for exposed edges with Melamine polish, handles, etc all complete as directed by engineer-in-charge.
456	E/M WORKS(Power Wiring)
457	Supplying and fixing 20 A, 415 V, TPN Industrial type socket outlet, with 4 pole and earth, metal enclosed plug top along with 20 A \"C\" curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.
458	Supply, Installation, Testing and commissioning for Geyser 25 Litre capacity storage type operating on single phase Ac supply 330 Volt 50Hz power supply and including high capacity steel wire mwsh Pipe suitable size with washers and nuts, fixinf on wall/ surface including necessary connection, complete all as spoecified and as directed.
459	45W LED street light fittings with GI bend pipe (Philips : BRP052 LED 045 CW SLMR FG S1 PSU GR)
460	Supply of 1.1KV, 4CX16sqmm XPLE insulated and PVC sheathed Al Armoured Cable as per IS 7098 Part-1
461	Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.
462	Upto 35 sq. mm
463	Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required. Upto 35 sq. mm
464	Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.
465	4 X 16 sq. mm (28mm)
466	Supplying and fixing cable route marker with 10 cm X 10 cm X 5 mm thick G.I. plate with inscription there on, bolted /welded to 35 mm X 35 mm X 6 mm angle iron, 60 cm long and fixing the same in ground as required.
467	Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 Meter long etc. with charcoal/ coke and salt as required
468	Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. pipe from earth electrode including connection with brass nut, bolt, spring, washer excavation and re-filling etc. as required.
469	Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.
470	(PART-III)PROVISION OF ARBORICULTURE ALONG 750 MTRS LONG STRETCH OF SECURITY WALL OF MAIN CAMPUS AT NPOL, KOCHI
471	Providing and stacking of Hibiscus/ Ixora variegated of height 60-75 cm. With 8-10 branches and healthy variegated follaige in cement pots of size 35 cm as per direction of the officer-in-harge
472	Digging holes 60 cm dia and 60 cm deep in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure afte reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any with all leads and lifts
473	LAWN
474	Trenching in ordinary soil up to a depth of 60 cm including removal and stacking of serviceable materials and then disposing of surplus soil by spreading and neatly levelling within a lead of 50m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or/and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure.
475	Rough dressing the trenched ground including breaking clods, Uprooting weeds from the trenched area after 10 to 15 days of its flooding with water including disposal of uprooted vegetation, Fine dressing of the ground etc complete.
476	Supply & laying Selection no. 1 doob grass turf with earth 50mm to 60mm thickness of existing ground prepared with proper level and ramming with required tools wooden and than rolling the surface with light roller make the surface smoothen and light watering the same and maintenance for 30 days or more till the grass establish properly, as per direction of the officer in charge.
477	HEDGES
478	Providing and Displaying Acalypha red well developed with fresh & healthy 30 to 45 cm ht. in 20 cm size Earthen Pot/ Plastic Pot as per direction of the officer-in-charge.
479	Providing and stacking of Bougainvillea (Variety Butiana, Lady Mary Baring, Mahara,Mohan,Scarlet Queen, Variegated, Glabra Formosa, Peruviana Odissi, Paratha, Subhra,Thimma, Spectabilis L.N Birla, Refulgens) of height 30 cm. to 45 cm. with 2-3 branches in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-charge.
480	Providing and stacking of Duranta Golden, having ht.15 to 20 cm bushty shape with fresh and healthy leaves in 15 cm size of Earthen Pot / Plastic Pot & as per direction of the officer-incharge.
481	Providing and stacking of plant Canna dwarf of height 25 to 30 cm., 2 to 3 suckers in earthen pots of size 20 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge.
482	Providing and displaying of Schefflera high colour plant, having ht. 25 cm to 30 cm, well developed with fresh & healthy foliage in 25 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge.
483	Providing and stacking of Nerium oleander (kaner) of height 45-60 cm. with 3-4 branches in poly bags of size 20 cm as per direction of the officer-in-charge.
484	Providing and stacking Allamanda cathartica of height 30 cm to 45 cm. in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-charge.
485	Digging holes45 cm dia and 45 cm deep in ordinary soil and refilling the same with the excavted earth mixed with manure or sludge in the ratio of 2:1 by volume ( 2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus erth, if any with all leads and lifts
486	Complete maintenance of shrubs (out side garden features) jobs like making of basin at regular interval i/c watering, weeding, pruning and application of tertilizer etc., and as per direction of officeer-in-charge. As per BOQ item No. 1 & 2 above.
487	Complete maintenance of the entire garden features having as per yard stick in the garden area i.e. lawn trees, shrubs, herbs, edge, flower beds, foliages, creepers etc. including hoeing, weeding, pruning, replacement of plants, gap filling, watering, mowing of lawn, grass cutting by lawn mover and brush cutter, removal of garden waste, applying insecticide, pesticide & fertilizers(whenever required) top dressing of lawn with good earth and manure and maintenance of other garden related works as directed by office-in-charge (Cost of Good Earth, Manure, Fertilizer, Insecticide, Pesticide will be provided by the Department & lawn mover and brush cutter with fuel and other T & P material/articles shall be provided by the contractor.) and as per direction of officer in charge. As per BOQ item No. 4 & 5 above.
488	Cutting of Hedge/Edge upto 1.2 mtr. Height including removing of cut material, cleaning, hoeing of hedge/edge bed watering, manureing and applying insecticides and fungicides etc., (excluding the cost of material which shall be supplied ber the department and as per direction of officer-in-charge. (Considering 10 Nos hedges per Sqm. As per BOQ item No. 6 to 12 above.
489	MATERIALS
490	Supplying and stacking of good earth at site including royalty and carriage upto 5 km lead complete (earth measured in stacks will be reduced by 20% for payment)
491	Supplying and stacking at site dump manure Screened through sieve of I.S. designation 4.75 mm from approved source including carriage upto 5 km lead complete (manure measured in stacks will be reduced by 8% for payment)
492	Sprinklers and Dip Irrigation System
493	Providing and fixing 3 layer PP-R (Polypropylene Random Copolymer) pipes confirming to IS :15801 UV stabilized and anti-microbial fusion welded, having thermal stability for hot and cold water supply including all PP-R plain and brass threaded polypropylene random fittings,including trenching, refilling and testing of joints complete as per the direction of Engineer-in-Charge
494	PN-16 Pipe, 63mm OD(SDR 7.4)
495	PN-16 Pipe, 50mm OD(SDR 7.4)
496	PN-16 Pipe, 32mm OD(SDR 7.4)
497	Supply and fixing PPR Union
498	PPR Union 63mm
499	PPR Union, 50mm
500	PPR Union, 32mm

Tender Documents

SR No	FileName	File Description
1	Click here to download tender document	Tender Documents
2	Click here to download tender document	Tender Documents
3	Click here to download tender document	Tender Documents
4	Click here to download tender document	Tender Documents
5	Click here to download tender document	Tender Documents
6	Click here to download tender document	Tender Documents
7	Click here to download tender document	Tender Documents
8	Click here to download tender document	Tender Documents
9	Click here to download tender document	Tender Documents
10	Click here to download tender document	Tender Documents
11	Click here to download tender document	Tender Documents
12	Click here to download tender document	Tender Documents
13	Click here to download tender document	Tender Documents

Also Visit

Tenders

Kerala Tenders

Construction Tenders

Building Construction Tenders

Building Work Tenders

Disclaimer

We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.

Top

Tender For Addition/ Alteration And Special Repairs To Certain Buildings For Dromi At Npol, Kochi And At Uarf, Kulamavu Alongwith Provision Of Arboriculture Work Along Security Wall Of Main Campus At Npol, Kochi, Kochi-Kerala

Tender Documents

Disclaimer

About Us

Services

Browse Tenders

For Sales Inquiry

Tender For Addition/ Alteration And Special Repairs To Certain Buildings For Dromi At Npol, Kochi And At Uarf, Kulamavu Alongwith Provision Of Arboriculture Work Along Security Wall Of Main Campus At Npol, Kochi, Kochi-Kerala

Tender Documents

Disclaimer

OTP Verification

About Us

Services

Browse Tenders

For Sales Inquiry

Connect With Us