Tender For Development Of Nursing And Paramedical College At Kavaratti, Lakshadweep, Kavaratti-Lakshadweep

TDR : 52942856

Tender Notice
BOQ

20 Days Left

Kavaratti , Lakshadweep

Tender Brief : Tender For Development Of Nursing And Paramedical College At Kavaratti, Lakshadweep

Document Fees
Refer document

EMD
₹ 13024943.0 /-

Tender Value
₹ 120.24 Crore /-

Submission Date
05-01-2026

Competition Type
Indian

Bidding Type
Tender

Need a Business Loan? Apply Now !


1	Civil Work : Providing material and labour, machinery forEarth work in excavation by mechanical means/ manual means over areas exceeding 30 cm in depth, including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, for all lead, all lift/ depth anywhere from the site etc complete as directed by Engineer in charge. for all kind of soil.
2	Providing material and labour, machinery Below 1.5 m in depth including additional lift of 1.5 m or part thereof in excavation / banking excavated or stacked materials including getting out and disposal of excavated earth for all lift/ depth anywhere from the site etc complete as directed by Engineer in charge. for all kind of soil.
3	Providing material and labour, machinery for Earth workwith Extra rates for quantities of works, executed, in or under water and/or liquid mud, including dewatering as requiredall lead, all lift/ depth anywhere from the site etc complete as directed by Engineer in charge.
4	Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering.(Ramping by manual or mechanical means)
5	Providing, material and labour for Excavating, supplying and filling in foundation, plinth, trenches and plot filling with local earth (brought from out side) including royalty CBR value higher than 8% by mechanical transport with all lead, including ramming and watering, consolidation of the earth in layers not exceeding 20 cm etc. complete as directed by Engineer in charge.
6	Disposal of moorum/building rubbish/ malba/ un-used excavatedearth, similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting, unloading to approved municipal dumping ground for lead upto 10 km for all lifts, complete as per directions of Engineer-in-charge.
7	Providing material and labour for filling in plinth with sand with CBR value higher than 8% under floors, base of foundations, wherever required including watering, ramming, consolidating and dressing complete as directed by Engineer in charge.
8	Providing and filling in rubbles in foundation, in plinth and for plinth protection, filling, with quarry spalls covering and leveling the surface in layers of 20 cm thickness stone/metals or stone chips, including watering, ramming well and consolidating each layer using minimum 100mm cut size stones. (Ramping by manual or mechanical means)
9	Supplying chemical emulsion Chlorpyriphos/ Lindane emulsifiable concentrate of 20% in sealed containers including delivery as specified including all lead and lift anywhere from the site etc complete as directed by Engineer in charge.
10	Carrying out plinth treatment of soil under floors/ existing floors using chemical emulsionto pre/ post construction/ existing structure With Diluting and injecting chemical emulsion Chlorpyriphos/Lindane E.C. 20% with 1% concentration by spraying chemical solution for termite controltreatment including labour and material consistment with I.S.I specification. (one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor.) inclusive of one litre chemical emulsion application at the rate of 5Litre chemical / Sqm of surface is recommendedas per I.S. (excluding the cost of chemical emulsion)
11	Providing and laying cement mortar in 1:6 (1-Cement : 6-coarse sand) proportion in Floors, Plinth, Pavement, Road work including compacting, finishing, curing etc complete for all level, all height/ depth as directed by engineer in charge.
12	Providing material and labour for laying Plain cement concrete 1:4:8 (1- Cement : 4- Coarse sand : 8- crushed stone aggregates 40 mm nominal size) in Foundation, Plinth, Pavement, Road work including cost of formwork, compacting, finishing, curing etc complete for all level, all height/ depth as directed by engineer in charge.
13	Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete.All works upto plinth level : Concrete of M25 grade with minimum cement content of 330 kg /cum
14	Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. : All works above plinth level upto floor V level: Concrete of M25 grade with minimum cement content of 330 kg /cum
15	Providing material and labour for Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete all complete as per direction of engineer in charge.
16	Providing material and labour for Centering and shuttering including strutting, propping etc. and removal of form for Edges of slabs and breaks in floors and walls Under 20cm wide. all complete as per direction of engineer in charge.
17	Providing material and labour for Centering and shuttering including strutting, propping etc. and removal of form for Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. etc. for mass concrete.all complete as per direction of engineer in charge.
18	Providing material and labour for Centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platform. etc. for mass concrete.all complete as per direction of engineer in charge.
19	Providing material and labour for centering and shuttering including strutting, propping, steel scaffolding etc. and removal form of RCC works for Lintels, beams, plinth beams, girders, bressumers and cantilevers etc. for mass concrete.all complete as per direction of engineer in charge.
20	Providing material and labour Centering and shuttering including strutting, propping etc. and removal of form for Columns, Pillars, Piers, Abutments, Posts and Struts etc. for mass concrete.all complete as per direction of engineer in charge.
21	Extra for Providing material and labour for Centering and shuttering in circular work including strutting, propping etc. and removal of form for Columns, Pillars, Piers, Abutments, Posts and Struts etc. for mass concrete all complete as per direction of engineer in charge.
22	Providing material and labour Centering and shuttering including strutting, propping etc. and removal of form for Stairs, except spiral-staircases etc. for mass concrete.all complete as per direction of engineer in charge.
23	Providing material and labourCentering and shuttering including strutting, propping etc. and removal of form for Vertical and horizontal fins individually or forming box louvers band, facias and eaves boards etc. for mass concrete.all complete as per direction of engineer in charge.
24	Providing material and labour Centering and shuttering including strutting, propping etc. and removal of form for additional height over a height of 3.5 m, upto 4.5 m in Suspended floors, roofs, landing, beams and balconies (Plan area to be measured)where ever required with adequate bracing, etc. including cost of de-shuttering and decentering at all levels, for every additional height of 1 metre or part thereof (Plan area to be measured).etc. for mass concrete.all complete as per direction of engineer in charge.
25	Providing material and labour Centering and shuttering including strutting, propping etc. and removal of form for additional height over a height above 4.5 m, upto 6.5 m in Suspended floors, roofs, landing, beams and balconies (Plan area to be measured)where ever required with adequate bracing, etc. including cost of de-shuttering and decentering at all levels, for every additional height of 1 metre or part thereof (Plan area to be measured).etc. for mass concrete.all complete as per direction of engineer in charge.
26	Providing and laying SBR Polymer modified (of approved make @ minimum 2% by wt. of cement used) plain/reinforced concrete jacket for the structural members e.g. columns, pillars, piers, beams etc with concrete having the specified minimum characteristic compressive strength with ordinary portland cement, coarse sand and graded stone aggregate of 10mm maximum size in proportion as per design criteria with specified average thickness upto 100mm thick in Grade M 25 with cement content not less than 330 kg per cum, all-round existing core of RCC member. Note: Rates shall be for finished surface area of concrete and shall include the cost of making holes in existing RCC slab, if required, for pouring concrete in shuttering mould of jacket and appropriate approved Super-Plasticiser for rendering concrete as flowable self compacting and SBR polymer but shall exclude cost of reinforcement, Shear Keys, (Payment under this item shall be made only after proper wet curing has been done and surface has been satisfactorily evaluated by sounding/tapping with a blunt metal instrument)
27	Providing and Core cutting work in Stone/RCC/Brick structures of maximum 300mm depth upto 150mm Dia with required core-cutting wet drilling, fastners tools, labour and supervision etc complete.
28	Rebaring: Providing material and labour for Drilling/ Cleaning hole and injecting grouting chemical with the help of dispenser, into Stone masonry/RCC wall (with Hilti RE500 V3 injection system or Fischer FIS EM injection system or Equivalent) as per manufacturer\"s specification and structural consultant\"s specification and fixing rebar of the required diameter subsequently upto 20 mm dia. drill hole and 300mm anchoring depth. Fixing methodology shall be followed as per manufacturer’s guidelines. Steel will be paid under relevant item.Manufacture to submit Rebar Depth Calculation based on design loads & other parameters as provided by consultant and in accordance with EOTA-TR-023/029 “guidelines for post installed rebar connections” for approval. Rate shall be inclusive of all material, labour, necessary scaffolding etc complete for all floors, all height as directed by engineer in charge.
29	Supplying, cutting, bending, binding and placing in position Steel reinforcement TMT Bar Fe 500D reinforcement in all diameter confirming to relevant I.S. standards as per ISS 2502 and IS 1786 including cost of binding with GI wires and placing in position all completeas per direction of engineer-in-charge.
30	Providinganticorrosive treatment by FUSION BONDED EPOXY COATING (FBEC) confirming to IS13620:1993 at approved plant including testing of coating as per relevant IS, before bringing the coated bars on site, by mechanized & qualified process including blast cleaning, heating using Induction heater, electrostatically spraying the epoxy powder, complete fusion to give coating thickness 150 to 300 microns, gradual cooling without affecting the properties of steel, testing as per IS13620 / ASTMA775, flexibility/bend & holiday test, other applicable test for ASTM Standards. including To & Fro transportation of bars for sending at plant site etc. complete.
31	Cleaning of reinforcement from rust from the reinforcing bars to give it a total rust free steel surface by using alkaline chemical rust remover of approved make with paint brush and removing loose particles after 24 hours of its application with wire brush and thoroughly washing with water and allowing it to dry, all complete as per direction of Engineer-In-Charge.( for all dia. bars)
32	Providing and injecting Epoxy injection grout in concrete/RCC work of approved make in proportion recommended by the manufacturer into cracks/honey-comb area of concrete/ masonry by suitable gun/pump at required pressure including cutting of nipples after curing etc. complete as per directions of Engineer-in-Charge.
33	Steel works: Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.
34	Providing and fixing M.S. round holding down or anchor bolts with nuts and washer plates complete.
35	Steel work welded in built up sections/ framed work in gratings, frames, guard bar, ladder, railings, brackets, louvers, gates and similar works including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required..(Brand: Tata Steel, Jindal)
36	Providing precast cement concrete Jali 50 mm thk. 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 6mm nominal size ), reinforced with 1.6 mm dia mild steel wire, including centering and shuttering, roughening cleaning, fixing and finishing in cement mortar 1:3 (1 cement: 3 fine sand) etc. complete as directed by Engineer in charge.
37	Providing and fixing 150 mm wide Aluminium fluted strips 3.15 mm thick, sheet covering over expansion joints with iron screws as per design.
38	Providing and fixing of floor joint of 100 mm gap expansion joint system related with floor location as per drawings and direction of Engineer-In-Charge. The joints system will be of extruded aluminum base members, self aligning / self centering arrangement and support plates etc. as per ASTM B221-02. The system shall be such that it provides floor to floor /floor to wall expansion control system for various vertical localtion in load application areas that accommodates multi directional seismic movement without stress to it\"s components. System shall consist of metal profiles with a universal aluminum base member designed to accommodate various project conditions and finish floor treatments. The cover plate shall be designed of width and thickness required to satisfy projects movement and loading requirements and secured to base members by utilizing manufacturer’s pre-engineered self- centering arrangement that freely rotates / moves in all directions. The Self - centering arrangement shall exhibit circular sphere ends that lock and slide inside the corresponding aluminum extrusion cavity to allow freedom of movement and flexure in all directions including vertical displacement. Provision of Moisture Barrier Membrane in the Joint System to have watertight joint is mandatory requirement all as per the manufactures design and as approved by Engineer -in-Charge. (Material shall confirm to ASTM 6063).
39	Providing and fixing of wall joint of 100 mm gap expansion joint system related with wall joint (internal/external) location as per drawings and direction of Engineer-In- Charge. The joints shall be of extruded aluminum base members, self aligning / centering arrangement and support plates as per ASTM B221- 02. The material shall be such that it provides an Expansion Joints System suitable for vertical wall to wall/ wall to corner application, both new and existing construction in office Buildings & complexes with no slipping down tendency amongst the components of the Joint System. The Joint System shall utilize light weight aluminum profiles exhibiting minimal exposed aluminum surfaces mechanically snap locking the multicellular to facilitate movement. (Material shall confirm to ASTM 6063).
40	Providing and fixing of expansion joint system for roof of 100 mm gap of approved make and manufactures for various roof locations as per approved drawings and direction of Engineer-In-Charge. The joints shall be of extruded aluminum base members with, self aligning and self centering arragement support plates asper ASTM B221-02. The system shall be such that it provides watertight roof to roof/roof to corner joint cover expansion control system that is capable of accommodating multidirectional seismic movement without stress to its components. System shall consist of metal profile that incorporates a universal aluminum base member designed to accommodate various project conditions and roof treatments. The cover plate shall be designed of width and thickness required to satisfy movement and loading requirements and secured to base members by utilizing manufacturer’s pre-engineered self-centering arrangement that freely rotates / moves in all directions. The Self centering arrangement shall exhibit circular sphere ends that lock and slide inside the corresponding aluminum extrusion cavity to allow freedom of movement and flexure in all directions including vertical displacement. The Joint System shall resists damage or deterioration from the impact of falling ice, exposure to UV, airborne contaminants and occasional foot traffic from maintenance personnel. Provision of Moisture Barrier Membrane in the Joint System to have water tight joint is mandatory requirement. (Material shall confirm to ASTM 6063).
41	Providing material and labour for Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in Cement Mortar 1:4 (1- Cement : 4 -coarse sand) in any shape and thickness including finishing, racking of joints, curing, scaffolding for all height all level etc. complete as directed by engineer-in-charge.
42	Providing material and labour for Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level upto floor five level in Cement Mortar 1:4 (1- Cement : 4 -coarse sand) in any shape and thickness including finishing, racking of joints, curing, scaffolding for all height all level etc. complete as directed by engineer-in-charge.
43	Providing material and labour for Halfbrickmasonry in Brick work with common burnt clay F.P.S. (non modular) brick of class designation 7.5 in cement mortar 1:3 (1 cement : 3 coarse sand) in superstructure above plinth level and upto floor five level, in any shape and thickness including finishing, racking of joints, curing, scaffolding for all height all level etc. complete as directed by engineer-in-charge.
44	Providing and fixing up to floor five level precast cement concrete solid block, including hoisting and setting in position with cement mortar 1:3 (1 cement : 3 coarse sand), cost of required centering, shuttering complete, 1:1½:3 (1 Cement: 1½ coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).as per direction of Engineer-in-Charge at all heights.
45	Providing and laying sandbased autoclaved aerated cement blocks masonry with AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineerin-Charge. (The payment of RCC band and reinforcement shall be made for seperately).
46	Providing and fixing aluminium work of Anodised aluminium for fixed portion, shutters of doors, windows & ventilators, louvers including providing and fixing hinges/ pivots / sliding / louvers(anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) for doors, windows, ventilators and partitions with extruded built up standard tubular sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately)including providing and fixing hinges/ pivots / sliding and fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)
47	Filling the gap in between aluminium/ stone/ wood frame and adjacent RCC/Brick/ Stone/ wood/ Ceramic/ Gypsum work by providing weather/structural non sag elastomeric PU sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete, complying to ASTM C920, DIN 18540-F & ISO 11600
48	For Windows: Providing and fixing stainless steel (SS 304 grade) adjustable windows stays of approved quality and size with necessary stainless steel screws etc. to the side hung windows as per direction of Engineer-incharge complete.
49	Providing and fixing bright /matt finished Stainless Steel handles of approved size, quality & make with necessary screws etc all complete. (min. 125 mm length)
50	Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screwsin doors, windows, louvers as per drawings. etc. complete as per the directions of engineer-in-charge.
51	Providing and fixing factory made uPVC Two track two panels sliding window made of small series frame (40mm & above) 52 x 44 mm & sash (25mm & above) 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension, sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware\"s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.
52	Providing and fixing factory made uPVC Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) made of (big series 115mm & above x 45mm & above ) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension, sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware\"s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.
53	Providing and fixing factory made uPVC Fixed window / ventilator made of (small series 39mm & above x 39mm & above ) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension, comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), , uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware\"s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.
54	Providing and fixing factory made uPVC Three track three panels sliding door with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) made of (big series 115mm & above x 45mm & above) frame 116 x 45 mm &(44mm & abovesash 46 x 82 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension sliding glazed door comprising of uPVC multichambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension uPVC extruded glazing beads, uPVC extruded interlock and uPVC extruded Inline sash adaptor (if required), EPDM gasket, wool pile, zinc alloy (white powder coated) handle with key on one side of extreme panels along with zinc plated mild steel multi point locking having transmission gear with keeps, zinc alloy (white powder coated) cresent lock (if required), stainless steel (SS 304 grade) body with adjustable double nylon rollers (weight bearing capacity to be 120 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware\"s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.
55	Providing and fixing glazing With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge .
56	Providing and fixing glazing With float glass panes of 8 mm thickness (weight not less than 12.50 kg/sqm) in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and as per the directions of engineer-in-charge .
57	Providing and fixing M.S. grills Fixed to window/ openings /wooden frames with rawl plugs screws etc. of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.
58	Providing superior class teak wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).
59	Providing and fixing ISI marked flush door shutters 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.complete as per the direction of Engineer-in-charge. Including, providing & fixing 1-1.5 mm thick decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side, both side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. Providing and fixing lipping with teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured). complete as per the direction of Engineer-in-charge.
60	Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.
61	Providing and fixing rectangular/ square/ circular vision panel in all type of flush doors complete as per the direction of Engineer-in-charge, including providing and fixing glazing With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) in door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge .
62	Providing and fixing bright finished 100 mm mortice lock with 6 levers without pair of handles of approved quality for aluminium door, with necessary screws etc complete as per direction of Engineer- incharge.
63	Providing and fixing ISI marked flush door shutters 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.complete as per the direction of Engineer-in-charge. Including, providing & fixing 1-1.5 mm thick decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede / waterproof (marine) finish with high density protective surface layer and reverse side, both side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. Providing and fixing lipping with teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured). complete as per the direction of Engineer-in-charge
64	Providing and fixing ISI marked flush door shutters 25 mm thick including ISI marked nickel plated bright finished M.S. Piano hinges IS : 3818 marked with necessary screws,with louvers provided in flush door shutters with approved size and material, conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.complete as per the direction of Engineer-in-charge. Including, providing & fixing 1-1.5 mm thick decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede / waterproof (marine) finish with high density protective surface layer and reverse side, both side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. Providing and fixing lipping with teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured). complete as per the direction of Engineer-in-charge
65	Providing and fixing stainless steel handle of approved make and size fixed with SS screws etc. complete as per direction of Engineer-in-charge. (min. 150 upto 200 mm length)
66	Providing and fixing bright finished chromium plated brass /sstower bolts of approved quality and size with necessary screws etc. complete as per direction of Engineer-incharge.
67	Providing Stainless steel dash fastener of required size (8 mm dia and 75 mm long bolt) as per direction of Engineer-inchargeall complete. (min. 8 nos. each)
68	Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately).
69	Providing and fixing aluminium tubular handle bar 32 mm outer dia, 3.0 mm thick & 2100 mm long with SS screws etc .complete as per direction of Engineer-in-Charge.
70	Providing and fixing fire resistant door frame of section 50 x 60 mm on horizontal side & 35 x 60 mm on vertical sides having built in rebate made out of 1.6 mm thick GI sheet ( Zinc coating not less than 120gm/m²) suitable for mounting 120 min Fire Rated Glazed Door Shutters. The frame shall be filled with Mineral wool Insulation having density min 96Kg/m³ . The frame will have a provision of G.I. Anchor fastners 14 nos ( 5 each on vertical style & 4 on horizontal style of size M10 x 80 ) suitable for fixing in the opening along with Factory made Template for SS Ball Bearing Hinges of Size 100x89x3mm for fixing of fire rated glazed shutter . The frame shall be finished with a approved fire resistant primer or Powder coating of not less than 30 micron in desired shade as per the directions of Engineer - in- charge . (Cost of SS ball bearing hinges is excluded).
71	Providing and fixing 60 mm thick glazed fire resistant door shutters of 120 min Fire Rating confirming to IS:3614 (Part II) or EN1634-1:1999, tested and certified as per laboratory approved by Engineer-in-charge, with suitable mounting on door frame, consisting of vertical styles, top rail & side rail 60 mm x 60 mm wide and bottom rail of 110 mm x 60 mm made out of 1.6mm thick G.I. sheet (zinc coating not less than 120gm/m²) duly filled mineral wool insulation having density min 96 kg/m³ and fixing with necessary stainless steel ball bearing hinges of size 100x89x3mm of approved make, including applying a coat of approved fire resistant primer or powder coating not less than 30 micron etc all complete as per direction of Engineer-in-charge (panelling to be paid for seperately).
72	Providing and fixing panic bar / latch (Double point) fitted with a single body, Trim Latch & Lock on back side of the Panic Latch of reputed brand and manufacture to be approved by the Engineer- in- charge, all complete.
73	Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adeq+D77uate strength conforming to IS: 4454 -part 1 and M.S. top cover of required thickness for rolling shutters. 80x1.20 mm M.S. laths with 1.20 mm thick top cover
74	Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge. (Only weight of grill to be measured for payment).
75	Providing and fixing stainless steel ( Grade 316) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). Sample shall be approved before execution. Contractor shall arrange mock up of railing system (2 or 3 no) in required length as directed by Architect. Contractor shall protect railing system uptill handling over the project.
76	Providing plaster drip course/ groove in plastered surface or moulding to R.C.C. projections and horizontal surfaces.
77	Providing material and labour for fixing GI wire mesh, of required size at junction of concrete and brick work or between different materials, as per instruction given by either architects or engineer in charge.
78	Providing and applying 6mm cement plaster, Cement plaster 1:3 (1 cement: 3 fine sand) finished with a floating coat of neat cement. as per instruction from architect or engineer incharge. on ceilings and sofits of stairs upto all levels/floors.
79	Providing and applying 15 mm cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement on the rough side of single or half brick wall/ aac block/ solid block wall as per instruction from architect or engineer incharge.
80	Rough cast plaster upto 10 m height above ground level with a mixture of sand and gravel or crushed stone from 6 mm to 10 mm nominal size, dashed over and including the fresh plaster in two layers, under layer 12 mm cement plaster 1:4 (1 cement : 4 coarse sand) and top layer 10 mm cement plaster 1:3 (1 cement : 3 fine sand) mixed with 10% finely grounded hydrated lime by volume of cement. : Ordinary cement finish using ordinary cement
81	Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof.
82	Providing and applyinh 18-20 mm cement mala plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement : 5 coarse sand) and a top layer 6 mm thick cement plaster 1:3 (1 cement : 3 coarse sand) finished rough with sponge. complete as directed by the Engineer-in-charge.
83	Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm
84	Finishing walls with 100% exterior Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives. New work (Two or more coats applied @ 1.43 litre/ 10 sqm. Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm.
85	Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.
86	Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. : two Coats
87	Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content. : With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre
88	Providing and applying, Finishing with With ready mixed red oxide zinc chromate primer second coat of approved brand and manufacture on steel galvanised iron/ steel works and Epoxy paint (two or more coats) on steel works at all locations prepared and applied as per manufacturer\"s specifications including appropriate priming coat, preparation of surface, etc. complete.
89	Providing and applying corrugated translucentacrylic sheet / Polycarbonate roofing sheet thickness as required with necessary screws and rubber silicon sealer etc complete as directed by Engineer in charge.
90	Providing corrugated G.S. sheet roofing 1.00 mm thick with zinc coating not less than 275 gm/m² including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.
91	Providing and fixing double scaffolding system (cup lock type) on the exterior side, up to seven story height made with 40 mm dia M.S. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with M.S. tubes, M.S. tube challies, M.S. clamps and M.S. staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it there after .The scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspection of work at required locations with essential safety features for the workmen etc. complete as per directions and approval of Engineer-in-charge .The elevational area of the scaffolding shall be measured for payment purpose .The payment will be made once irrespective of duration of scaffolding.
92	Providing and applying Hot dip Galvanised coating confirming toIndian Standard 4579/2629/2633 with zinc coating thickness to be 86 micron and before application ofGI coating the material should be free from all dirt, grease, varnish, paint or any other foreign matter. Including touching of local exposed areas with Zincmetal spray paint with 2 coats to make the structure corrosion free with cleaning thoroughly the applied surface making it free from grease, paint or any other foreign matter , sanding the surface before and after the paint to provide seamless aestheic look complete as per the instructions of the EIC including transport/loading/unloading the materials at plant for HDGC work
93	Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.
94	Providing and laying cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) and providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer\"s specification. in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor, slabs etc., up to floor five level. complete as per direction of engineer-in-charge.
95	Providing and laying six courses water proofing treatment with bitumen felt over roofs, balconies wherever required consisting of first, third and fifth courses of blown or / and residual bitumen applied hot at 1.45, 1.20 and 1.70 kg per square metre of area respectively, second and fourth courses of roofing felt type 2 grade II (glass fibre base self finished bitumen felt) and sixth and final course of stone grit 6 mm and down size or pea sized gravel spread at 6 cubic decimeter per sqm including preparation of surface but excluding grading, complete.
96	Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer\"s specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction the Engineer in Charge but excluding the cost of painting with : : 12.5 mm thick tapered edge gypsum moisture resistant board
97	Providing and fixing false ceiling at all heights with integral densified calcium silicate reinforced with fibre and natural filler false ceiling tiles of Size 595x595mm of approved texture, design and patterns as per CPWD Specification 2019, to be laid in true horizontal level suspended on inter-locking metal T-Grid of hot dipped galvanised iron section of 0.33mmthick (galvanized @ 120 grams per sqm including both sides)comprising of main-T runners of size 24x38 mm of length 3000 mm,cross - T of size 24x32 mm of length 1200 mm and secondaryintermediate cross-T of size 24x32 mm of length 600mm to formgrid module of size 600 x 600 mm, suspended from ceiling usinggalvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 12x50 mm long dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 76x25x25x1.6 mm fixed with grid and Z cleat of size 25x37x25x1.6mm thick with precut hole on both 25mm flange to pierce into 12x50mm or even bigger size dash fastener if require, fixed with Glavanised iron perimeter wall angle or size 24x24x0.40 mm of length 3000 mm to be fixed on periphey wall / partition with the help of plastic rawl plugs at 450mm center to center and 40 mm long dry wall S.S screws. The workshall be carried out as per specifications, drawing and as per directionsof the Engineer-in-Charge. With 15 mm thick Tegular edged light weight calcium sliciate false ceiling tiles
98	Providing and laying vitrified tiles in different sizes (thickness to be specified by the manufacturer) in floors, skirting, dado with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge.
99	Providing and laying Double charge vitrified tile polished finish in floor/wallls/ skirtings in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.
100	Providing and laying Glazed Vitrified tiles Antiskid finish of in floor/wallls/ skirtings in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.
101	Fixing glazed/ Ceramic/ Vitrified tiles/ granite/ granite gang saw wherever required with cement based high polymer modified quick-set tile adhesive (Water based) conforming to IS: 15477, in average 3mm thickness. All complete as per direction of enginner in charge.
102	Providing and laying Polished Granite stone in flooring, stairs, skirtings in required design and patterns, in linear/ verical as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent
103	Providing and fixing 18 mm thick granite stone gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen sandwitch platforms, vanity counters vertical supports, window sills, facias, skirting, riser of steps, dado and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.
104	Providing edge moulding to 18 mm thick granite/marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.
105	Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.
106	Providing and fixing granite stone slab of approved shade with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth.
107	Providing material and labour for surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish including all lead and lift anywhere from the site etc complete as directed by Engineer in charge. for all kind of soil.
108	Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good theundulations etc. and re-rolling the sub grade and disposal of surplus earthwith lead upto 50 metres.
109	Construction of granular sub-base With material conforming to Grade-II (size range 53 mm to 0.075 mm ) having CBR Value-25 by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge.
110	Construction of dry lean cement concrete sub base over a prepared sub-grade with coarse and fine aggregate conforming to IS:383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per specifications, cement content not to be less than 150 Kg/cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant, transported to site, for all leads & lifts, laid with a mechanical paver, compacting with 8-10 tonne vibratory roller, finishing and curing etc. complete as per direction of Engineer-in- charge.
111	Providing and laying design mix cement concrete of M30 grade, Broom finish/ Polished in roads/ taxi tracks/ runways, using cement content as per design mix, using coarse sand and graded stone aggregate of 40 mm nominal size in appropriate proportions as per approved & specified design criteria, providing dowel bars with sleeve/ tie bars wherever required, laying at site, spreading and compacting mechanically by using needle and surface vibrators, levelling to required slope/ camber, finishing with required texture, including steel form work with sturdy M.S. channel sections, curing, making provision for contraction/ expansion, construction & longitudinal joints (10 mm wide x 50 mm deep) by groove cutting machine, providing and filling joints with approved joint filler and sealants, complete all as per direction of Engineer-in-charge (Item of joint fillers, sealants, dowel bars with sleeve/ tie bars to be paid separately). Cement concrete prepared with batch mixing machine.
112	Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).
113	Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 600 mm dia. RCC pipe
114	Providing and applying 2.5 mm thick road marking strips (retro- reflective) of specified shade/ colour using hot thermoplastic material by fully/ semi automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour, T&P, cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. complete as per direction of Engineer-in-charge and accordance with applicable specifications.
115	Providing and fixing Glow studs of size 100x20 mm made of heavy duty body shall be moulded ASA (Acrylic styrene Acryloretrite ) or HIP (High impact polystyrene) or ABS having electronically welded micro- prismatic lens with abrasion resistant coating as approved by Engineer in charge. The glow stud shall support a load of 13635 kg tested in accordance with ASTM D4280. The slope of retro- reflective surface shall be 35 (+/-5) degress to base .The reflective panels on both sides with at least 12 cm of reflective area up each side. The luminance intensity should be as per the specification and shall be tested as described in ASTM I: 809 as recommended in BS: 873 part 4 : 1973. The studs shall be fixed to the Road surface using the adhesive conforming to IS, as per procedure recommended by the manufacturer complete and as per direction of Engineer-in-charge.
116	Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge (Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.)
117	Providing and laying 25 mm thick Kota stone slab flooringover 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand)
118	Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.
119	Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge.
120	Providing and laying matt finished vitrified tile of size 100x100x16mm having water absorption less than 0.5% and conforming to IS: 15622 of approved make in all colours and shades in out door floors such as footpath, court yard multi models etc., laid on 20mm thick base of cement mortar 1:4 (1cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as direction of Engineer-in-Charge.
121	Providing and laying tactile tile (for vision impaired persons as per standards) of size 300x300x9.8mm having with water absorption less than 0.5% and conforming to IS:15622 of approved make in all colours and shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge.
122	Providing and fixing 10x10x7.50 cm Granite cobble stone block hand cut and chisel dressed on top, for paving in floors, drains etc. laid over 20mm thick base mortar 1:4 (1 cement : 4 coarse sand) with joints 10mm wide filled with same mortar including ruled pointing etc. complete as per direction of engineer-in-charge.
123	Providing and laying 500x500x40 mm thick Turf paver (Turfpave XD) on 150 mm thick sub grade of compacted bed of 20 mm thick nominal size stone aggregate and base course and filling with 150 mm thick jamuna sand, including spreading, well ramming, consolidating and finishing smooth etc. all complete as per direction of Engineer-in-charge.
124	Providing and fixing Precast Composite Concrete Litter Bin of 600x600x1000 with SS 316 Top lid (LxBxH) element with terrazzo Texture finish made of Full Depth Terrazzo mix High Performance GlassFiber Reinforced Concrete 12 MPa flexural strength and 40MPa Compressive Strength, UV resistant stabilise colour pigment, colour as per Architectschoice, including fixing, cleaning surfaces and including cost of loading -unloading and placing with crane. (Make: Artemis, Concrete shop, Arya Precast)
125	Providing and fixing square swing Dustbin of 100 - 110 litre capacity of size 450x450x750 mm height to be fixed in precast bin made of Grade SS 304 grade fixed with permanent structure as per the details fixed with required base plate, Matt finish. (Brands MrBIN, Greenrevolution, Chevron)
126	Providing Precast Glass Fibre Reinforce Concrete Pebble Seat of 600 mm dia and 400 mm height & 100 mm thickness single cast mono element with terrazzo smooth finish made of Full Depth Terrazzo mix High Performance GlassFiber Reinforced Concrete 12 MPa flexural strength and 40MPa Compressive Strength, UV resistant stabilise colour pigment, colour as per Architectschoice including fixing, cleaning surfaces and complete and including cost of loading -unloading and placing with crane. (Make: Artemis, Concrete shop, Arya Precast)
127	Providing Precast Concrete Modular backless bench of 1800x450x450 LBH & 100 mm thickness single cast mono element with terrazzo smooth finish made of Full Depth Terrazzo mix High Performance GlassFiber Reinforced Concrete 12 MPa flexural strength and 40MPa Compressive Strength, UV resistant stabilise colour pigment, colour as per Architects choice including fixing, cleaning surfaces and cost of loading -unloading and placing with crane.(Make: Artemis, Concrete shop, Arya Precast)
128	Providing and fixing flag mast of required size upto 20 mtrs. mast shaft shall be in two sections, hot dip galvanised and suitable for wind velocity as per IS 875 with FRP dome, Mast shall be suitable for Indian Tri Color Flag Size as per standards, Mast shall be PU painted, Supply of System for Raising Lowering of Flag. It Shall have double drum winch, 6mm dia galvanised wire rope and integral power tool for the raising and lowering of Flag. Suitable Control switch shall be provided for reversing operation of Power tools Motor. Supply of foundation bolts manufactured from special steel along with nuts, washers, anchor plate and common template. Size- M30 x 8 nos, 850 MM long, Anchore & Template Plate PCD- 490 mm (8 Hole), Supply of Single Dome LED Aviation Obstruction light & AOL system which include LED Avaition system & CU Armd Cable 3C x 2.5Sqmm. Supply of 5M high hot dip galvanised octagonal pole suitable to mount 1no.LED 350W flood light fittings at top with suitable mounting arrangement at bottom. Supply of foundation bolts manufactured from special steel along with nuts, washers etc. Supply of LED floodlight type 350W, Make CG/Havells/Bajaj, Supply of national flag of size - as required in 100% knitted Polyester (140gsm), with reinforced super-strong nylon webbing on all 3 sides & rope/toggle sleeve. with 25 years of warranty.(Make: valmont, Bajaj)
129	Trenching in ordinary soil up to a depth of 60 cm including removal and stacking of serviceable materials and then disposing of surplus soil, by spreading and neatly levelling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or / and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure).
130	Supplying,stacking, spreading and mixing in the required proportion specified of good earth, sludge, manure screened through sieve of I.S. designation 4.75 mm at site (including royalty) and carriage upto 5 km lead complete as per direction of officer-in-charge.
131	Grassing with selection No. 1 Doob grass including fine dressing of the ground,watering and maintenance of the lawn for 30 days or more till the grass forms a thick lawn, free from weeds and fit for mowing including supplying good earth, if needed, In rows 5 cm apart in both directions, as per direction of officer-in-charge.
132	Transplantation of trees with in a distance of 2km including excavation around existing tree, pruning of branches, lifting, loading and transportation of existing tree, digging pits for placing tree at new place, adding manure, sand, fertilizer, hormones and bio fertilizer to it. Levelled and neatly dressed and disposal of surplus materials from old existing and new sites to designated place. Each tree should be firmly secured to the stake so as to prevent excessive movement, flooding with water, treatment of roots, rope and gunny bags as per direction of the officer incharge. T&P and all required materials shall be arranged by the contractor and nothing extra shall be paid on this account. (a) Girth of tree shall be measured at a height of 1m above ground level.Girth of trees beyond 50cm and upto 90cm.
133	Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)
134	Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.
135	Extra for cutting reinforcement bars manually/ by mechanical means in R.C.C. or R.B. work (Payment shall be made on the cross sectional area of R.C.C. or R.B. work) as per direction of Engineer-in-charge.
136	Extra for scrapping, cleaning and straightening reinforcement from R.C.C. or R.B. work.
137	Demolishing brick /concrete block work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement motar
138	Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : Of area beyond 3 sq. metres
139	Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead :Of area beyond 3 sq. metres
140	Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within 50metres lead.
141	Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. For thickness of tiles 10 mm to 25 mm
142	Dismantling stone slab flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 metres lead.
143	Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within 50 metres lead of: GI sheet
144	Dismantling of flushing cistern of all types (C.I./PVC/Vitrious China) including stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead.
145	Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.
146	Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceable material with in 50 meters lead as directed by Engineer-in-charge.
147	Felling trees of the girth (measured at a height of 1 m above ground level), including cutting of trunks and branches, removing the roots and stacking of serviceable material and disposal of unserviceable material. Beyond 30 cm girth upto and including 60 cm girth.
148	Felling trees of the girth (measured at a height of 1 m above ground level), including cutting of trunks and branches, removing the roots and stacking of serviceable material and disposal of unserviceable material. Beyond 60 cm girth upto and including 120 cm girth.
149	Felling trees of the girth (measured at a height of 1 m above ground level), including cutting of trunks and branches, removing the roots and stacking of serviceable material and disposal of unserviceable material. Beyond 120 cm girth upto and including 240 cm girth.
150	Taking out existing CC interlocking paver blocks from footpath/ central verge, including removal of rubbish etc., disposal of unserviceable material to the dumping ground, for which payment shall be made separately and stacking of serviceable material with all lead and lift, as per direction of Engineer-in-Charge.
151	Electrical work : Wiringforlightpoint/fanpoint/exhaustfanpoint/callbell pointwith1.5SqmmFRLSPVCinsulatedcopperconductor single core cable in surface / recessed medium class PVC conduit,withmodular switch,modularplate,suitableGIbox andearthingthepointwith1.5SqmmFRLSPVCinsulated copper conductor single core cable etc. as required. Group-C
152	Wiring for group controlled (looped) light point/fan point / exhaust fan point / call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductorsinglecorecableinsurface/recessedPVCconduit, andearthingthepointwith1.5sq.mmFRLSPVCinsulated copper conductor single core cable etc. as required. Group-C
153	Wiring for circuit/ submain wiring alongwith earth wire with the followingsizesofFRLSPVCinsulatedcopperconductor,single corecableinsurface/recessedmediumclassPVCconduitas required. 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire
154	Wiring for circuit/ submain wiring alongwith earth wire with the followingsizesofFRLSPVCinsulatedcopperconductor,single corecableinsurface/recessedmediumclassPVCconduitas required.2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire
155	Wiring for circuit/ submain wiring alongwith earth wire with the followingsizesofFRLSPVCinsulatedcopperconductor,single corecableinsurface/recessedmediumclassPVCconduitas required. 2 X 4 sq. mm + 1 X 4 sq. mm earth wire
156	Wiring for circuit/ submain wiring alongwith earth wire with the followingsizesofFRLSPVCinsulatedcopperconductor,single corecableinsurface/recessedmediumclassPVCconduitas required. 2 X 6 sq. mm + 1 X 6 sq. mm earth wire
157	Supplyingand drawingfollowingpair0.5mmdiaFRLSPVC insulatedannealedcopperconductor,unarmoredtelephone cableintheexistingsurface/recessedsteel/PVCconduitas required. 4 Pair
158	Supplyinganddrawingco-axialTVcableRG-6grade,0.7mm solidcopperconductorPEinsulated,shieldedwithfinetinned copperbraidandprotectedwithPVCsheathintheexisting surface/ recessed steel/ PVC conduit as required.
159	SupplyingandfixingoffollowingsizesofmediumclassPVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 20MM
160	SupplyingandfixingoffollowingsizesofmediumclassPVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 25 mm- as per description 1.21.1
161	SupplyingandfixingoffollowingsizesofmediumclassPVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 32 mm- as per description 1.21.1
162	Supplying and fixing metal box of following sizes (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc. as required. 150 mm X 150 mm X 60 mm deep
163	Supplying and fixing metal box of following sizes (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc. as required. 200 mm X 250 mm X 75 mm deep
164	Supplying and fixing metal box of following sizes (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc. as required. 250 mm X 300 mm X 100 mm deep
165	Supplyingandfixingfollowingmodularswitch/socketonthe existingmodularplate&switchboxincludingconnections but excluding modular plate etc. as required. Telephone socket outlet
166	Supplyingandfixingfollowingmodularswitch/socketonthe existingmodularplate&switchboxincludingconnections but excluding modular plate etc. as required. TV antenna socket outlet
167	Supplyingandfixing twomodulesteppedtypeelectronicfan regulatorontheexistingmodularplateswitchboxincluding connections but excluding modular plate etc. as required.
168	Supplying and fixing suitable size GI box with modular plate and coverinfrontonsurfaceorinrecess,includingprovidingand fixing3pin5/6Amodularsocketoutletand5/6Amodular switch, connections etc. as required.
169	Supplying and fixing suitable size GI box with modular plate and coverinfrontonsurfaceorinrecess,includingprovidingand fixing6pin 5/6 &15/16Amodular socket outlet and 15/16A modular switch, connections etc. as required.
170	SupplyinganddrawingofUTP4pairCAT6LANCableinthe existing surface/ recessed Steel/ PVC conduit as required. 1 run of cable
171	Supplying and fixing suitable size GI box with modular plate and coverinfrontonsurfaceorinrecess,includingprovidngand fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular switch, connections etc. as required. (For light plugs to be used in non residential buildings).
172	Laying ofone numberPVC insulated and PVC sheathed/ XLPE powercableof1.1KVgradeoffollowingsizeintheexisting RCC/ HUME/ METAL/DWC/HDPE pipe as required. Up to 35 sq. mm
173	Laying ofone numberPVC insulated and PVC sheathed/ XLPE powercableof1.1KVgradeoffollowingsizeintheexisting RCC/ HUME/ METAL/DWC/HDPE pipe as required. 35 sq. mm and upto 95 sq. mm
174	Laying ofone numberPVC insulated and PVC sheathed/ XLPE powercableof1.1KVgradeoffollowingsizeintheexisting RCC/ HUME/ METAL/DWC/HDPE pipe as required.95 sq. mm and upto 185 sq. mm
175	Laying and fixing of one number PVC insulated and PVC sheathed / XLPE powercable of1.1KV gradeof following size on cable tray as required. Upto 35 sq. mm (clamped with 1mm thick saddle)
176	Supplying & erecting XLPE(IS:7098)(I)-88 ISI unarmoured copper cable 1.1 KV grade to be erected as directed of following size. (E)3 core 2.5 Sq. mm
177	Supplying & erecting XLPE(IS:7098)(I)-88 ISI unarmoured copper cable 1.1 KV grade to be erected as directed of following size(F) 3 core 4 Sq. mm -As per description 4.2.1
178	Supplying & erecting XLPE(IS:7098)(I)-88 ISI unarmoured copper cable 1.1 KV grade to be erected as directed of following size (L) 4 core 6 Sq. mm-As per description 4.2.1
179	Supplying & erecting XLPE(IS:7098)(I)-88 ISI unarmoured copper cable 1.1 KV grade to be erected as directed of following size(M) 4 core 10 Sq. mm-As per description 4.2.1
180	Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for1.1 KV. to be laidon wall with necessary clamps or in existing trench/ pipe of following size of cables. (A) 3 core 4.0 Sq. mm
181	Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for1.1 KV. to be laidon wall with necessary clamps or in existing trench/ pipe of following size of cables. (A-1) 3 1/2core 35 Sq. mm ( 16 Sq. mm 1/2 core)
182	Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for1.1 KV. to be laidon wall with necessary clamps or in existing trench/ pipe of following size of cables(B) 3 1/2 core 50 Sq. mm ( 25 Sq.1/2 mmcore)
183	Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for1.1 KV. to be laidon wall with necessary clamps or in existing trench/ pipe of following size of cables(C) 3 1/2 core 70 Sqmm (35 Sqmm 1/2 core)
184	Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for1.1 KV. to be laidon wall with necessary clamps or in existing trench/ pipe of following size of cables (D) 3 1/2 core 95 Sqmm (50 Sqmm1/2 core) - As per description 4.3.3
185	Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for1.1 KV. to be laidon wall with necessary clamps or in existing trench/ pipe of following size of cables (E) 3 1/2core 120 Sq. mm (70Sq. mm 1/2 core) -As per description 4.3.3
186	Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for1.1 KV. to be laidon wall with necessary clamps or in existing trench/ pipe of following size of cables (F) 3 1/2core 150 Sq. mm (70Sq. mm 1/2 core) -As per description 4.3.3
187	Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for1.1 KV. to be laidon wall with necessary clamps or in existing trench/ pipe of following size of cables (G) 3 1/2core 185 Sq. mm (70Sq. mm 1/2 core) -As per description 4.3.3
188	Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for1.1 KV. to be laidon wall with necessary clamps or in existing trench/ pipe of following size of cables. (b) 4 core 6 Sq. Mm
189	Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for1.1 KV. to be laidon wall with necessary clamps or in existing trench/ pipe of following size of cables (c) 4 core 10 Sq. mm
190	Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for1.1 KV. to be laidon wall with necessary clamps or in existing trench/ pipe of following size of cables (d) 4 core 16 Sq. mm
191	Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for1.1 KV. to be laidon wall with necessary clamps or in existing trench/ pipe of following size of cables (e) 4 core 25 Sq. mm
192	Supplying and making end termination with brass compression glandandaluminiumlugsforfollowingsizeofPVCinsulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required 3½ X 50 sq. mm (35mm)
193	Supplying and making end termination with brass compression glandandaluminiumlugsforfollowingsizeofPVCinsulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required 3½ X 70 sq. mm (38mm)
194	Supplying and making end termination with brass compression glandandaluminiumlugsforfollowingsizeofPVCinsulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required 3½ X 95 sq. mm (45mm)
195	Supplying and making end termination with brass compression glandandaluminiumlugsforfollowingsizeofPVCinsulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required 3½ X 95 sq. mm (45mm)
196	Supplying and making end termination with brass compression glandandaluminiumlugsforfollowingsizeofPVCinsulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required 3½ X 95 sq. mm (45mm)
197	Supplying and making end termination with brass compression glandandaluminiumlugsforfollowingsizeofPVCinsulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required 3½ X 95 sq. mm (45mm)
198	Supplying and making end termination with brass compression glandandaluminiumlugsforfollowingsizeofPVCinsulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required 3½ X 95 sq. mm (45mm)
199	Supplying and making end termination with brass compression glandandaluminiumlugsforfollowingsizeofPVCinsulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required 3½ X 95 sq. mm (45mm)
200	Supplying and making end termination with brass compression glandandaluminiumlugsforfollowingsizeofPVCinsulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required 3½ X 95 sq. mm (45mm)
201	Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 cm below ground level) including excavation andrefillingthetrenchbutexcludingsandcushioning and protective covering etc., complete as required. 63 mm dia (OD-63 mm & ID-51 mm nominal)
202	Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 cm below ground level) including excavation andrefillingthetrenchbutexcludingsandcushioning and protective covering etc., complete as required.90 mm dia (OD-90 mm & ID-76 mm nominal)
203	Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 cm below ground level) including excavation andrefillingthetrenchbutexcludingsandcushioning and protective covering etc., complete as required. 120 mm dia (OD-120 mm & ID-103 mm nominal)
204	Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 cm below ground level) including excavation andrefillingthetrenchbutexcludingsandcushioning and protective covering etc., complete as required.160 mm dia (OD-160 mm & ID-135 mm nominal)
205	Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenientsections,joinedwithconnectors,suspendedfrom the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 100 mm width X 50 mm depth X 1.6 mm thickness
206	Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenientsections,joinedwithconnectors,suspendedfrom the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 150 mm width X 50 mm depth X 1.6 mm thickness
207	Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenientsections,joinedwithconnectors,suspendedfrom the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 300 mm width X 50 mm depth X 1.6 mm thickness
208	Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenientsections,joinedwithconnectors,suspendedfrom the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 450 mm width X 50 mm depth X 2.0 mm thickness
209	Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray \"bends\" (galvanisation not lessthan 50microns)withperforation notmore than 17.5%, in convenientsections,joinedwithconnectors,suspendedfrom the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 100 mm width X 50 mm depth X 1.6 mm thickness
210	Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray \"bends\" (galvanisation not lessthan 50microns)withperforation notmore than 17.5%, in convenientsections,joinedwithconnectors,suspendedfrom the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.150 mm width X 50 mm depth X 1.6 mm thickness
211	Supplying and installing following size of perforated Hot Dipped GalvanisedIroncable tray \"Tee\" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections,joinedwithconnectors,suspendedfromtheceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 100 mm width X 50 mm depth X 1.6 mm thickness
212	Supplying and installing following size of perforated Hot Dipped GalvanisedIroncable tray \"Tee\" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections,joinedwithconnectors,suspendedfromtheceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required 150 mm width X 50 mm depth X 1.6 mm thickness
213	Supplying and installing following size of perforated Hot Dipped GalvanisedIroncabletray\"Crossmember\"(galvanisationnot less than 50 microns) with perforation not more than 17.5%, in convenientsections,joinedwithconnectors,suspendedfrom the ceilingwith G.I. suspendersincluding G.I.bolts & nuts, etc as required. 100 mm width X 50 mm depth X 1.6 mm thickness
214	Supplying and installing following size of perforated Hot Dipped GalvanisedIroncabletray\"Crossmember\"(galvanisationnot less than 50 microns) with perforation not more than 17.5%, in convenientsections,joinedwithconnectors,suspendedfrom the ceilingwith G.I. suspendersincluding G.I.bolts & nuts, etc as required 150 mm width X 50 mm depth X 1.6 mm thickness
215	Supplying and installing following size of perforated Hot Dipped GalvanisedIroncabletray\"Reducer\"(galvanisationnotless than50microns)withperforationnotmorethan17.5%,in convenientsections,joinedwithconnectors,suspendedfrom the ceilingwith G.I. suspendersincluding G.I.bolts & nuts, etc as required. 100 mm width X 50 mm depth X 1.6 mm thickness
216	Supplying and installing following size of perforated Hot Dipped GalvanisedIroncabletray\"Reducer\"(galvanisationnotless than50microns)withperforationnotmorethan17.5%,in convenientsections,joinedwithconnectors,suspendedfrom the ceilingwith G.I. suspendersincluding G.I.bolts & nuts, etc as required. 150 mm width X 50 mm depth X 1.6 mm thickness
217	Supplying and installing following size of perforated Hot Dipped GalvanisedIroncabletray\"Reducer\"(galvanisationnotless than50microns)withperforationnotmorethan17.5%,in convenientsections,joinedwithconnectors,suspendedfrom the ceilingwith G.I. suspendersincluding G.I.bolts & nuts, etc as required. 300 mm width X 50 mm depth X 1.6 mm thickness
218	Supplying and installing following size of perforated Hot Dipped GalvanisedIroncabletray\"Reducer\"(galvanisationnotless than50microns)withperforationnotmorethan17.5%,in convenientsections,joinedwithconnectors,suspendedfrom the ceilingwith G.I. suspendersincluding G.I.bolts & nuts, etc as required. 450 mm width X 50 mm depth X 2.0 mm thickness
219	Excavation forcabletrenchesin softsoil,depthupto1.2m including dressing of sides lift upto 1.5 m, including getting out the excavated soil, refillingwith sand andor goodsoilafter laying of cable/ pipe etc in layers of 20 cm, ramming, watering and disposalof surplus excavated soil as directed, within a lead of 50 metres.
220	Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5
221	Supplyingandfixingfollowingway,singlepoleandneutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, completewithtinnedcopperbusbar,neutralbusbar,earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 6 way , Double door
222	SWITCHGEAR, PANEL & ACCESSORIES:Supplyingandfixingfollowingway,singlepoleandneutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, completewithtinnedcopperbusbar,neutralbusbar,earth bar, din bar, interconnections, powder painted including earthing etc. as required 12 way , Double door
223	Supplyingandfixingfollowingway,horizontaltypethreepole andneutral,sheetsteel,MCBdistributionboard,415V,on surface/recess,completewithtinnedcopperbusbar,neutral busbar,earthbar,dinbar,interconnections,powderpainted includingearthingetc.asrequired.(Butwithout MCB/RCCB/Isolator) 6 way (4 + 18), Double door
224	SWITCHGEAR, PANEL & ACCESSORIES:Supplyingandfixingfollowingway,singlepoleandneutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, completewithtinnedcopperbusbar,neutralbusbar,earth bar, din bar, interconnections, powder painted including earthing etc. as required 8 way (4 + 24), Double door
225	Supplyingandfixingoffollowingwayssurface/recess mounting, verticaltype, 415V, TPNMCBdistributionboard of sheetsteel,dustprotected,dulypowderpainted,inclusiveof 200Atinnedcopperbusbar,commonneutrallink,earthbar, din bar for mounting MCBs (but without MCBs and incomer ) as required.(Note:VerticaltypeMCBTPDBisnormallyused where 3 phase outlets are required.)
226	Supplyingandfixing5Ato32A rating, 240/415V, 10kA,\"C\" curve,miniaturecircuitbreakersuitableforinductiveloadof followingpolesintheexistingMCB DBcompletewith connections, testing and commissioning etc. as required. Single pole
227	Supplyingandfixing5Ato32A rating, 240/415V, 10kA,\"C\" curve,miniaturecircuitbreakersuitableforinductiveloadof followingpolesintheexistingMCB DBcompletewith connections, testing and commissioning etc. as required. Double pole
228	Supplyingandfixing5Ato32A rating, 240/415V, 10kA,\"C\" curve,miniaturecircuitbreakersuitableforinductiveloadof followingpolesintheexistingMCB DBcompletewith connections, testing and commissioning etc. as required. Triple pole
229	Supplyingandfixing5Ato32A rating, 240/415V, 10kA,\"C\" curve,miniaturecircuitbreakersuitableforinductiveloadof followingpolesintheexistingMCB DBcompletewith connections, testing and commissioning etc. as required. Triple pole and neutral
230	Supplying and fixing following rating, double pole, (single phase andneutral),240V,residualcurrentcircuitbreaker(RCCB) , havingasensitivitycurrent30mAintheexistingMCBDB completewithconnections,testingandcommissioningetc.as required. 25 A
231	Supplying and fixing following rating, double pole, (single phase andneutral),240V,residualcurrentcircuitbreaker(RCCB) , havingasensitivitycurrent30mAintheexistingMCBDB completewithconnections,testingandcommissioningetc.as required. 40 A
232	Supplyingandfixingfollowingrating,fourpole,(threephase and neutral), 415 volts, residual current circuit breaker (RCCB), havingasensitivitycurrent30mAintheexistingMCBDB completewithconnections,testingandcommissioningetc.as required. 25 A
233	Supplyingandfixingfollowingrating,fourpole,(threephase and neutral), 415 volts, residual current circuit breaker (RCCB), havingasensitivitycurrent30mAintheexistingMCBDB completewithconnections,testingandcommissioningetc.as required.40 A
234	Providing and fixing M.V. danger notice plate of 200 mm X 150 mm,madeofmildsteel,atleast2mmthick,andvitreous enameled white on both sides, and with inscription in single red colour on front side as required.
235	SITC of 4-Way VTPN DB, IP43 metal door. Double door with arrangement for FPMCCB, TPMCBs/FPMCBs. Make: Havell\"s, Legrand, Schneider, ABB
236	Suppling testing and comissining of 63A FP MCCB.
237	Suppling testing and comissining of 100A FP MCCB.
238	SITC of Panels of below ratings as per IS Specifications and respective drawings. The unit rate for each item shall include :Call for final inspection prior to dispatch. Delivery of the panels to site. Shifting of the panels from site store to the suitable location. Fixing of Shipping Section. Assembly and wiring of component supplied separately. Installation of panel to Electric Room including removing packing. Earthing all components, frame etc. to a common internal earth bar. M.S. parts should be painted with powder coating. Supply & Fixing all accessories and supporting structure. Supply & Fixing of M.100 mm. channels for fixing the panels. Connection, Testing & Commissioning. Checking of Internal connection and wiring, operation of switches, starter, TPN MCCB, relays, contractors etc. Supply of necessary tools, hardware, mounting with necessary civil masonary works etc.Electrical Contractor shall carry out the insulation test at site and all the observations shall be recoreded and submitted in duplicate to the consultant or engineer - in - charge. The rate shall include the civil foundation as approved by site enginner. Make: Schnieder, ABB, Siemense, L&T, Havell\"s. SITC of Indoor type Main LT Panel-1 (Electrical Room) as per above specifications. Incomer : 800A, FP ACB. Busbar: 800A TPN, 415V,3-Phase 15KA Al. RYB, On, Off, Trip Indicating Lamp-6 NOS with VSS & Voltmer. Control Fuse - 3 NOS. MFM - 1 NO. CT 800/5A 3 NOS (for Measuring Current) with ASS & Ammeter. CT 800/5A 3 NOS (for APFC Relay). Buscoupler : 800A, TPN Microprocessor Based 45KA, ACB. 1no. 800A FP ATS. 1 no. 160A FP MCCB. Outgoings : 1nos. 250A FP MCCB, 2nos. 200A FPMCCB, 2nos. 125A FP MCCB, 1no. 100A FPMCCB, 4nos. 63A FP MCCBs, 2no. 40A FPMCBs, 2nos. 32A TPMCBs, 2nos. 25A DP MCBs. 2nos. digital timer. Contractor must consider 100KVAR APFCR panel including the main panel. All MCCBs must be microprocessor based. NOTE: Panel design might vary as per final working. Contractor must follow the SLD before execution.
239	SITC of Outdoor type Feeder Section Panel-1 (Near Type-2 & Security Cabin) as per above specifications. Incomer : 250A, FP MCCB. Busbar: 250A TPN, 415V,3-Phase 15KA Al. RYB, On, Off, Trip Indicating Lamp-6 NOS with VSS & Voltmer. Control Fuse - 3 NOS. MFM - 1 NO. CT 250/5A 3 NOS (for Measuring Current) with ASS & Ammeter. 1no. 250A FP ATS (Auto Transfer Switch) Outgoings : 1no. 125A FP MCCB, 1nos. 80A FP MCCB, 2nos. 63A FP MCCB, 2nos. 40A FP MCB, 4nos. 25A TP MCB, 2no.s 25A DPMCBs. 2nos. digital timer for street poles. All MCCBs must be microprocessor based. NOTE: Panel design might vary as per final working. Contractor must follow the SLD before execution.
240	SITC of Outdoor type Feeder Section Panel-2 (Near Girls Hostel) as per above specifications. Incomer : 200A, FP MCCB. Busbar: 200A TPN, 415V,3-Phase 15KA Al. RYB, On, Off, Trip Indicating Lamp-6 NOS with VSS & Voltmer. Control Fuse - 3 NOS. MFM - 1 NO. CT 200/5A 3 NOS (for Measuring Current) with ASS & Ammeter. 1no. 200A FP ATS (Auto Transfer Switch) Outgoings : 1no. 125A FP MCCB, 2nos. 63A FP MCCB, 2nos. 40A FP MCB, 4nos. 25A TP MCB, 2no.s 25A DPMCBs. 2nos. digital timer for street poles. All MCCBs must be microprocessor based. NOTE: Panel design might vary as per final working. Contractor must follow the SLD before execution.
241	SITC of Indoor type Floor Panel-1 (Girls Hostel) as per above specifications. Incomer : 125A, FP MCCB. Busbar: 125A TPN, 415V,3-Phase 15KA Al. RYB, On, Off, Trip Indicating Lamp-6 NOS with VSS & Voltmer. Control Fuse - 3 NOS. MFM - 1 NO. CT 125/5A 3 NOS (for Measuring Current) with ASS & Ammeter. 1no. 125A ATS (Auto Transfer Switch). Outgoings : 2nos. 40A FPMCB, 1no. 63A FP MCCB, 10nos. 32A FP MCBs, 1no. 32A DPELCB, 2nos 25A TPMCBs, 2nos. 25A DPMCBs. All MCCBs must be microprocessor based. NOTE: Panel design might vary as per final working. Contractor must follow the SLD before execution. Make: ABB, Scheneider, L&T, Havell\"s, Siemens
242	SITC of Indoor type Floor Panel-2 (Type-2 Quarters-2BHK) as per above specifications. Incomer : 80A, FP MCCB. Busbar: 80A TPN, 415V,3-Phase 15KA Al. RYB, On, Off, Trip Indicating Lamp-6 NOS with VSS & Voltmer. Control Fuse - 3 NOS. MFM - 1 NO. CT 80/5A 3 NOS (for Measuring Current) with ASS & Ammeter. 1no. 80A ATS (Auto Transfer Switch). Outgoings: 6nos. KWh Meters. 6nos. 32A DPMCBs, 1no. 25A DP MCB, 1nos. 32A FP MCBs, 1no. 25A DPMCB, 1nos 25A TPMCB. All MCCBs must be microprocessor based. NOTE: Panel design might vary as per final working. Contractor must follow the SLD before execution. Make: ABB, Scheneider, L&T, Havell\"s, Siemens
243	SITC of Indoor type Floor Panel-3 (Type-4 Quarters-3BHK) as per above specifications. Incomer : 125A, FP MCCB. Busbar: 125A TPN, 415V,3-Phase 15KA Al. RYB, On, Off, Trip Indicating Lamp-6 NOS with VSS & Voltmer. Control Fuse - 3 NOS. MFM - 1 NO. CT 125/5A 3 NOS (for Measuring Current) with ASS & Ammeter. 1no. 125A ATS (Auto Transfer Switch). Outgoings: 8nos. KWh Meters. 8nos. 40A FPMCBs, 1no. 25A DP MCB, 2nos. 32A FP MCBs, 2no. 25A DPMCB, 2nos 25A TPMCB. All MCCBs must be microprocessor based. NOTE: Panel design might vary as per final working. Contractor must follow the SLD before execution. Make: ABB, Scheneider, L&T, Havell\"s, Siemens
244	SITC of Indoor type Floor Panel-4 (Type-3 Quarters-2BHK) as per above specifications. Incomer : 125A, FP MCCB. Busbar: 125A TPN, 415V,3-Phase 15KA Al. RYB, On, Off, Trip Indicating Lamp-6 NOS with VSS & Voltmer. Control Fuse - 3 NOS. MFM - 1 NO. CT 125/5A 3 NOS (for Measuring Current) with ASS & Ammeter. 1no. 125A ATS (Auto Transfer Switch). Outgoings: 12nos. KWh Meters. 12nos. 40A DPMCBs, 1no. 25A DP MCB, 2nos. 32A FP MCBs, 2no. 25A FPMCB, 2nos 25A TPMCB. All MCCBs must be microprocessor based. NOTE: Panel design might vary as per final working. Contractor must follow the SLD before execution. Make: ABB, Scheneider, L&T, Havell\"s, Siemens
245	SITC of Indoor type Floor Panel-5 (College Building) as per above specifications. Incomer : 200A, FP MCCB. Busbar: 200A TPN, 415V,3-Phase 15KA Al. RYB, On, Off, Trip Indicating Lamp-6 NOS with VSS & Voltmer. Control Fuse - 3 NOS. MFM - 1 NO. CT 200/5A 3 NOS (for Measuring Current) with ASS & Ammeter. 1no. 200A ATS (Auto Transfer Switch). Outgoings: 10nos. 40A FPMCBs, 4no. 32A DP MCB, 2nos. 32A FP MCBs, 2no. 63A FPMCB, 3nos 25A TPMCB. 2nos. 25A DPMCBs. All MCCBs must be microprocessor based. NOTE: Panel design might vary as per final working. Contractor must follow the SLD before execution. Make: ABB, Scheneider, L&T, Havell\"s, Siemens
246	SITC of Indoor type Floor Panel-6 (Paramedical Building) as per above specifications. Incomer : 100A, FP MCCB. Busbar: 100A TPN, 415V,3-Phase 15KA Al. RYB, On, Off, Trip Indicating Lamp-6 NOS with VSS & Voltmer. Control Fuse - 3 NOS. MFM - 1 NO. CT 100/5A 3 NOS (for Measuring Current) with ASS & Ammeter. 1no. 100A ATS (Auto Transfer Switch). Outgoings: 8nos. 40A FPMCBs, 2no. 32A DP MCB, 2nos. 32A FP MCBs, 1no. 63A FPMCB, 3nos 25A TPMCB. 2nos. 25A DPMCBs. All MCCBs must be microprocessor based. NOTE: Panel design might vary as per final working. Contractor must follow the SLD before execution. Make: ABB, Scheneider, L&T, Havell\"s, Siemens
247	Earthingwithcopperearthplate600mmX600mmX3mm thickincludingaccessories,andprovidingmasonryenclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc.with charcoal/ coke and salt as required.
248	Supplyingandlaying25mmX5mmG.Istripat0.50metre belowgroundasstripearthelectrode,includingconnection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)
249	Providingandfixing25mmX5mmG.I.striponsurfaceorin recess for connections etc. as required.
250	Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required.
251	Installation, testingand commissioning ofceilingfan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable includingprovidingandfixingphenoliclaminatedsheetcover on the fan box etc. as required.
252	Supplying and fixing extra conduit down rod of 20 cm length G.I. pipe 15 mm dia, heavy gauge including painting etc. As required. (Note : More than 5 cm length shall be rounded to the nearest 10 cm and 5 cm or less shall be ignored)
253	Numberingofceilingfan/exhaustfan/fluorescentfittingsas required.
254	Installationofexhaustfanintheexistingopening,including makinggoodthedamage,connection,testing,commissioning etc. as required. Upto 450 mm sweep
255	Installationofexhaustfanintheexistingopening,including makinggoodthedamage,connection,testing,commissioning etc. as required. Upto 510 mm sweep
256	Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes.
257	SITC of IP66, IK07, 40W LED (4000K) modern post top lantern type decorative light fixture with 4 Meter die cast aluminium pole of 100mm Dia. including following specifications:Die cast EN-AB-47100 aluminium housing with high corrosion resistance. Stainless steel screws. Clear toughned glass 6mm thick. Luminaire with single cable entry and gormmet. Silicon gasket. Double powder paint. 150mm dia base plate with necessary bolts and fittings. Buried in ground upto 600mm depth. Powder coated as per approved colour with weather proof coat. All required cable connection with suitable MCB mounting inside the pole. 4000K CRI80 3360lm. Rated Luminaire luminous fluux 1721lm. Rated input power 40W, 220V-240V AC 50/60 HZ. Make: Disano, Neri, Kesselec, Ligman, Klite. Contractor must submit the sample to the consultant/architect or engineer incharge before execution. Fixture warranty must be 3 years minimum.
258	SITC of IP66, IK06, 12W LED Uplighter (spike/bracket type) with following specifications. 4000K. Luminaire housing & bracket made of die cast aluminium, aluminium & SS fasteners. Clear tempered safety glass. Mounting earth spike or die-cast bracket arrangement to facilitate easy installation at any desired location. Swivel range of the luminaire in the horizontal axis 0°-90°. Luminaire supplied with one metre cable length and a IP67 connector. Silicone gasket. Cable entries for through-wiring of mains supply cable. Integral constant current power supply. CRI ( Ra) : ≥80. Prewired with LED driver and suitable for operating on 240V, 50Hz single phase ac supply. Contractor has to make 300mmx150mm deep or higher rcc foundation for spike/bracket fixing. Make: Dissano, Neri, Ligman, Klite. Contractor must submit the sample to the consultant/architect or engineer incharge before execution. Fixture warranty must be 3 years minimum.
259	SITC of IP66, IK06, 6W LED Uplighter (spike/bracket type) with following specifications. 4000K. Luminaire housing & bracket made of die cast aluminium, aluminium & SS fasteners. Clear tempered safety glass. Mounting earth spike or die-cast bracket arrangement to facilitate easy installation at any desired location. Swivel range of the luminaire in the horizontal axis 0°-90°. Luminaire supplied with one metre cable length and a IP67 connector. Silicone gasket. Cable entries for through-wiring of mains supply cable. Integral constant current power supply. CRI ( Ra) : ≥80. Prewired with LED driver and suitable for operating on 240V, 50Hz single phase ac supply. Contractor has to make 300mmx150mm deep or higher rcc foundation for spike/bracket fixing. Make: Dissano, Neri, Klite. Contractor must submit the sample to the consultant/architect or engineer incharge before execution. Fixture warranty must be 3 years minimum.
260	SITC of IP65, IK07, weather proof & corrosion resistant 12W LED Wall Down Light type fixture with following specifications. Square/Cylindrical Shape, open surface, medim wide beam angle with symmetrical distribution, 3000k. Die-cast aluminium housing. Stainless steel fasteners in grade 316. Durable silicone rubber gasket. High efficiency optical reflector. Clear toughened glass. Single cable entry. Housing is treated with a chemical chromatised protection before powder coating, ensuring high corrosion resistance. Fixture colour must be as per consultant/architect\"s approval. Make: Ligman, Neri, K-lite, Uniled. Contractor must submit the sample to the consultant/ architect before execution. Fixture warranty must be 3 years minimum.
261	SITC of IP65, IK08, 24W LED Open Surface Mounted Bulkhead type Light fixture with following specifications. Shielded, 3000k, Corrosion resistant die-cast aluminium frame and body. Stainless steel fasteners in grade 316. Durable silicone rubber gasket. Impact resistant UV stabilised polycarbonate diffuser. The luminaire is treated with a chemical, chromatised protection before powder coating, ensuring high corrosion resistance. Make: Ligman, Neri, K-lite, Uniled. Contractor must submit the sample to the consultant/architect or engineer incharge before execution. Fixture warranty must be 3 years minimum.
262	SITC of IP20, indoor, open surface 20/30W round cylindrical down light type fixture with all required accessories. 4000K. Luminaire made of die-cast aluminium for better thermal management. Die-cast aluminium inner ring with reflector for uniform light distribution. High PF constant current LED driver. Cable entries for through-wiring of mains supply cable. 30° beam angle. Suitable for operation on 240V, 50Hz single phase ac supply. Safety class II. White powder coated body colour or as per approved by the architect/consultant. Make: Ligman, Neri, K-lite, Uniled, Abby. Contractor must submit the sample to the consultant/architect or engineer incharge before execution. Fixture warranty must be 3 years minimum.
263	SITC of IP65, outdoor, open surface 18W round cylindrical down light type fixture with all required accessories. 4000K.Luminaire made of die cast aluminium, aluminium & SS fasteners. Clear tempered glass. Silicone gasket. Hybrid optics with lens & reflector combination for higher efficiency, lower optical losses with optimum glare suppression. Cast aluminium plate for surface mounting onto the ceiling. Surface mounting on ceiling using hardware after connecting to the power supply. Cable entries for through-wiring of mains supply cable. Integral constant current power supply. CRI ( Ra) : ≥80 ( 90 CRI - On Request ). Prewired with LED driver and suitable for operating on 240V, 50Hz single phase ac supply. Make: Ligman, Neri, K-lite, Uniled, Abby. Contractor must submit the sample to the consultant/architect or engineer incharge before execution. Fixture warranty must be 3 years minimum.
264	Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB,with housing used as a heat sink shall be made of thick sheet Steel conforming to IS: 513/CRCA polyester powder coated and high U.V. & corrosion resistancewith diffuser and/or Polycarbonate optics with company mark/name. 120 to 300 V,Power Factor more than 0.9, THD < 10 %, CCT4000 K to 6500K, Uniformity ratio >0.7,Luminaire efficacy> 85 lumens/watt , LED driver efficiency > 85 %.CREE / OSRAM / PHILIPS Lumileds / NICHIA / SEOUL/Bridgelux(U.S.A.) make LED used for luminaire. (Each fitting required LM-79 & LM-80 Certificates). Tube Light . 22/28 Watt LED Batten with integral/ non-integral driver, Surge - 4KV,IP-20,4 feet. Cat-III
265	Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB,with housing used as a heat sink shall be made of thick sheet Steel conforming to IS: 513/CRCA polyester powder coated and high U.V. & corrosion resistancewith diffuser and/or Polycarbonate optics with company mark/name. 120 to 300 V,Power Factor more than 0.9, THD < 10 %, CCT4000 K to 6500K, Uniformity ratio >0.7,Luminaire efficacy> 85 lumens/watt , LED driver efficiency > 85 %.CREE / OSRAM / PHILIPS Lumileds / NICHIA / SEOUL/Bridgelux(U.S.A.) make LED used for luminaire. (Each fitting required LM-79 & LM-80 Certificates). Tube Light . 12-15 Watt LED Batten with integral/ non-integral driver, Surge - 4KV,IP-20,2 feet. Cat-III
266	(C) Square/ Circular, Surface/Recessed Mounted Downlight with provision for spring loaded mounting clips complete. (b) 10-15 watts, Surge-4 KV. Cat-III
267	(C) Square/ Circular, Surface/Recessed Mounted Downlight with provision for spring loaded mounting clips complete.(c) 20-24 watts, Surge-4 KV
268	Supplying and erecting LED street light / Flood light fittings with High power White LEDs wattage of 1Watt and above assembled on single MCPCB, efficiency more than 130 lm/w and corrosion free High pressure die cast aluminum housing with smooth finish powder coated and heat sink extruded aluminium with diffuser and Polycarbonate optics/ lenses with company mark/name engraved or embossed 120 to 300 V,Power Factor more than 0.95, THD < 10 %, CCT5000 K to 5700K, Uniformity ratio >0.45, Luminaire efficacy> 85 lumens/watt . LED driver efficiency > 85 %. CREE / OSRAM / PHILIPS Lumileds / NICHIA / SEOUL/ BridgeLux (U.S.A.) make LED used for luminaire. ( Each fittings required LM-79 & LM-80 certificates). (B) Flood Light (IP-65), Surge -4KV. (d) above 100 to 120 watts. Cat-III
269	Supplying, installation, testing & commissioning of heat detector operatingat54ºC/57ºCwithrateofrisecumfixed temperature (dual thermistor)type with mounting base complete with all connection etc. as required.
270	Supplying, installation, testing & commissioning of smoke detector with builtin LED and mounting base complete with all connections etc. as required.
271	Supplying,installation,testing&commissioningofmanualcall boxes ofMSconstructionin surface/recess with stainless steel chain & hammer assembly complete with glass and push button etc. as required
272	Supplying, installation, testing & commissioning fire alarm sounder with facility to make announcement, mounted in M.S. box (16 SWG) with hinged cover plate & suitable for operation withamplifieri/clinematchingtransformeretc. complete as required.
273	Supplying,installation,testing&commissioningsectorpanel suitable for following zones, complete with visual indications for short circuit fault, open circuit fault, fire condition and all other standardfacilities as per IS:2189withmimicdiagramforall area/zone covered, complete with all connections, interconnections as required. 4 Zone
274	Supplying&layingof2x1.5sqmmfiresurvivalarmoured cable, 600/1000V rated with annealed copper conductor havingglassmicafirebarriertapecoveredbyanextruded layerof CrossLinkableEthylenePropyleneRubber(EPR) insulationandLSZHinnerbedding,steelwirearmouring&LSZH outer sheath complete as required.
275	Supplyingandfixing25mmdiaMSflexiblepipewithPVC coating along with all ancillaries and accessories like coupleretc. as required.
276	ABC Powdertype fire extinguisher of 6 Kgs. Capacity, with initial filling in brand new cylinder with powder coated finish, fitted with Gun metal union, high pressure gas cartridge, discharge hose, wall mounting bracket etc. complete, confirming to IS:15683 Make: Cease Fire or equivalent
277	CO2 type fire extinguisher of 4.5 Kgs. Capacity, with initial filling in brand new cylinder with powder coated finish, fitted with Gun metal union, high pressure gas cartridge, discharge hose, wall mounting bracket etc. complete, confirming to IS:15683. Make: Cease Fire or equivalent
278	Supply, Installation, Testing & Commissioning ofIP Network IR Dome Camera, 1/2.8\" CMOS, 2 MP, Min. Illumination required 0.05lux F1.4 color, 0Lux F1.4(IR on), 120dB True WDR, Min. Pixels 1920 × 1080, min. dual stream,2.7–12 mm motorized focus & zoom lens, BLC, HLC, 3DNR, Privacy Mask, IR LEDs Smart IR with upto 30m IR distance, 128GB SD card support, H.265, H.264 High Profile and MJPEG, PoE Class 3 and 12V DC, IP 66, IK10 rated vandal resisntant, Having Operating temp range : –30°C to 60° C. ONVIF Profile, cyber secured, UL, CE, FCC & RoHS certified. Approved Makes: Bosch, Axis, Honeywell, Avigilon
279	Supply, Installation, Testing & Commissioning ofIP Network IR Bullet Camera, 1/2.8\" CMOS, 2 MP, Min. Illumination required 0.05lux F1.4 color, 0Lux F1.4(IR on), 120dB True WDR, Min. Pixels 1920 × 1080, min. dual stream,2.7–12 mm motorized focus & zoom lens, BLC, HLC, 3DNR, Privacy Mask, IR LEDs Smart IR with upto 60m IR distance, 128GB SD card support, H.265, H.264 High Profile and MJPEG, PoE Class 3 and 12V DC, IP 66, Metal Body, Having Operating temp range : –30°C to 60° C. ONVIF Profile, cyber secured, UL, CE, FCC & RoHS certified. Approved Makes: Bosch, Axis, Honeywell, Avigilon
280	Supply, installation, testing and commissioning of 4Meter 90mm dia, GI pole for CCTV camera/LED light fitting including rcc foundation, junction box, MCB etc. and required accessories and connections.
281	SupplyinganddrawingofUTP4pairCAT6LANCableinthe existing surface/ recessed Steel/ PVC conduit as required. 1 run of cable
282	Supply, Installation, Testing and Commissioning of 8 Channel NVR with 4 SATA, with 1080pRealtime Live View H.265/H.264 MJPEG dual codec decoding Up to 12 MP resolution preview & playback Max 320 Mbps incoming bandwidth support 4 SATA HDDs up to 32TB, Supports fisheye videode-warping in local and web user interface,Supports visual or auditory notifications(a flashing light, bell,or siren) ONVIF compliant, UL, CE, FCC and & RoHS compliant. Approved Makes: Bosch, Axis, Honeywell, Avigilon
283	Supply, Installation, Testing and Commissioning of 16 Channel NVR with 4 SATA, with 1080pRealtime Live View H.265/H.264 MJPEG dual codec decoding Up to 12 MP resolution preview & playback Max 320 Mbps incoming bandwidth support 4 SATA HDDs up to 32TB, Supports fisheye videode-warping in local and web user interface,Supports visual or auditory notifications(a flashing light, bell,or siren) ONVIF compliant, UL, CE, FCC and & RoHS compliant. Approved Makes: Bosch, Axis, Honeywell, Avigilon
284	Supply, Installation, Testing and Commissioning of 24 Channel NVR with 4 SATA, with 1080pRealtime Live View H.265/H.264 MJPEG dual codec decoding Up to 12 MP resolution preview & playback Max 320 Mbps incoming bandwidth support 4 SATA HDDs up to 32TB, Supports fisheye videode-warping in local and web user interface,Supports visual or auditory notifications(a flashing light, bell,or siren) ONVIF compliant, UL, CE, FCC and & RoHS compliant. Approved Makes: Bosch, Axis, Honeywell, Avigilon
285	Supply, Installation, Testing and Commissioning of 32 Channel NVR with 8 SATA, with 1080pRealtime Live View H.265/H.264 MJPEG dual codec decoding Up to 12 MP resolution preview & playback Max 320 Mbps incoming bandwidth support 8 SATA HDDs up to 64TB, Supports fisheye videode-warping in local and web user interface,Supports visual or auditory notifications(a flashing light, bell,or siren) ONVIF compliant, UL, CE, FCC and & RoHS compliant. Approved Makes: Bosch, Axis, Honeywell, Avigilon
286	Supply, Installation, Testing and Commissioning of 12 TB HDD for Storage Approved Makes: Segate / WD
287	Supply, Installation, Testing And Commissioning of Layer 2 Managed Gigabit POE switch with 24 # 10/100/1000BaseT ports and 2 # Gigabit Combo ports(RJ45/SFP), 2 # Gigabit SFP Port. Approved Make: HP/ Cisco
288	Supply, Installation, Testing and Commissioning of Single UTP CAT6 RJ-45 I/O of specified make inclusive of termination of CAT6 cable at each IO including Singlex Face Plate for mounting IO with required back box. Approved Make: Polycab/ Tyco/ Molex.
289	Supply, Installation, Testing and Commissioning of 6U Wall Mounting Rack for Floor Distribution. Approved Make: Tata/APW/Valrack
290	Supply, Installation, Testing and Commissioning of 6Core Fiber Cable for Building Connectivity. Approved Make: Polycab/Tyco/Molex/CIS
291	Supply, Installation, Testing and Commissioning of Duplex LC To LC MM Fiber Patch Cord 3 Meter Approved Make: Polycab/Tyco/Molex/CIS
292	Supply and installation, testing and commissioning following size KRONE make telephone tag block in lockable 16 gauge sheet steel enclosure complete as required. 4 pair Krone type tag block
293	Supply and installation, testing and commissioning following size KRONE make telephone tag block in lockable 16 gauge sheet steel enclosure complete as required. 10 pair Krone type tag block
294	Supply and laying of specified make 0.51 mm dia Tinned copper Armoured telephone wire 10 pair telephone wire
295	Supply, Installation, Testing and Commissioning of Caller ID Telephone Instruments
296	Telephone System:Supply, Installation, testing and commissioning of Digital/PCM/TDMEPABXSystemhavingSMTdesign,systemwith flexibleuniversalslots,1 PRI, 104 nos of Extensions, 4 nos of IP channels, CPU and Power supply hot swappable (Redundancy), 8 port digital for KTS, 4-Port builtin GSM required (Sim Card), built in voice recording, Long distance capability required, outlook integration required for all users. Approved Make: NEC/ NEOS Infinity/ Avaya/ Panasonic
297	Supply, Installation, Testing and Commissioning ofOperator Console at Reception. Approved Make: Neos/Beetel/Panasonic/NEC
298	Supply, Installation, Testing and Commissioning ofDirector phone with KTS. Approved Make: Neos/Beetel/Panasonic/NEC
299	SITC of Boom Barrier system for basement parking entry and exit area with all accessories and following specifications. Boom Length (mt)- 6. Height of Boom from ground- 884-914 (Approx mm). Housing Dimensions (Approx mm)450 x 295 x 1007. Boom Dimension (mm)- 100 x 40. Controller Protecting Rating-IP54. Control Panel Power Supply (V) 230 A.C.50/60Hz. Motor Power Supply (V) 24 D.C. Power- 300W. Current Draw (A)- 1.5.Torque (Nm)-600. Opening Time (Sec)-3 to 6. Duty Cycle-Intensive use. Operating Temp. (°C) : -20 to +55. Bar with protective rubber profile to prevent injury in case of any contact. Circular boom section. Loop Detector.Traffic/flashing light. Including both manual and automatic operation. Optical beam sensor inclusive. Programmable for fast and low speed traffic. inclusive of electrica panel to accept signals for various controls and safety accessories.
300	Liaison fees for preparing necessary documents and drawings for getting N.O.C from Electricity Co. and Electrical Inspector for the installation of 11 KV / 0.433 KV Electrical L.T distribution sub stations. (All statutory fees will be paid by client)
301	Supplyingand erecting approved make online Un-interruptible Power Supply system comprising flat cum-boost charger, static Inverter & sealed maintenance free batteries. The charger having operating capacity for input 160-270V AC &inverter having output23OV,5O Hz Acwith 0.8 load power factor with battery, overunder voltage output with over load & short circuit protection equipment. The system housed in CRC sheet duly powder coated paint with following capacity & with Following size of batteries. (D) 5 KVA (i)With 11 Nos. of 12 V 55 Ah SMF batteries
302	Supply, Installation, Testing & Commissioning of Solar Roof Top Panels including all type of connections and equipments. Including all type of fabrication work, inverters, AC/DC distribution boards, cables, earthing. Cables on solar panels must be tied with the aluminium cable tie. Cement foundation of the fabrication must be in round shape and covered in pvc pipe of required size. Contractor must need to submit the layout of the solar roof top panel installation and approve the sample work with the architect/consultant/authorized government official. 5 years maintenance warranty shall be in the contractor\"s scope for all the equipments used and the installation work. Make: Adani make solar panel. Government Approved make solar inverter.
303	SITC of Lift suitable for min. 6/8 Passengers upto 15 Meter height with following specifications. (1200mm x 1400mm) Make: Mitsubishi, Schindeler, Kone. Load- 408kg/ 6 passengers.Speed- 0.63 mps. Direction- All at the same side. Rise Mts.- 20 Mts. Overhead- 4.8Mts. Power supply- 400 volts, 3-Phase, 50 Hz AC. Light Supply: 230 Volts, 50 Hz Single Phase. Machine- Geared placed above the hoistway in machine room. Control- Microprocessor based controller with VVVF. Operation- Down Collective ,Simplex. Platform Size (W * D ) -mm & Hoistway Require ( W * D ) -mm Car Enclosure- As per Standard. Flooring- PVC. False Ceiling- Standard. Car Door Type- Protected by S.S. Closed Door with Center Opening. Clear. Entrance Size ( W * H ) -mm- Standard. Landing Door- Same sa Lift doors. Door Frame- Standard. Door Operation- Automatic. Std. Fixtures/Signals: Touch Panel with Updown arrow, Auto/Manual Fan On/Off, Battery Operated Alarm Bell + Emergency Light, Automatic Rescue Device.
304	SITC of 500KVA Unitised Sub-Station with following specifications. IEC 62271-202, IS2026. IP54 for HT &Lt compartment. IP23D for Transformer compartment. Enclosure Class K10. Non-walk in type. Hermetically sealed Dry type transformer. As per the latest government norms. KVA Rating-500kva, HV voltage-11000 volts, LV voltage-433 volts, 3-phase, 50hz, Dry type, Air cooled, HV Connection- Delta, LV Connection- Star, Vector Group- Dyn11, Tapping on HV side- ±5% in steps of 2.5%, Eficiency at 100% Load- 99.01%, efficiency at 75% load- 99.18%, efficiency at 50% load- 99.32%, Temperature rise-50°C. Low noise level. Inbuilt stabilizer for stabilized power. Make: Kirloskar, ABB, Schneider, Eaton. The rate shall include the following : Supply and delivery of the USS at site. Unloading of USS at site. Shifting of USS with all tools, equipment & accessories from site store to the site and placing it on the plinth at site. Earthing of USS neutral & body. Charging gradually as per IS. Contractor has to submit all the test certificates to the site incharge.
305	Supplying and erecting, commissioning and testing Diesel Generating set having continuous rating, 500KVA including Canopy and AMF Panel, 3 phase, 415 volts, 50 cycles A.C. supply comprising of a totally enclosed air/water cooled diesel engine with multi-cylinders developing suitable BHP not less than following capacityat 1500 RPM with 10% overload for one hour in 24 hours with standard accessories like fly wheel, lubricating oil cooler, \"A\" class governor, heavy duty fuel wheel and lubricating oil filter, oil bath air filler, lubricating oil pressure gauge, end exhaust manifold, standard set of tools with adjustable spanners, screw drivers, feeder gauge, cylinder head to cover, joint cylinder head to exhaust, element lube oil filter, 12/24 volts electric starting equipment complete with standard battery, dynamo, cut-outs, ammeter, necessary wiring, pressure gauge, starter etc and heavy duty Residential type exhaust silencer and vertical hot air duct both. logged with asbestos rope, save oil trays, exhaust piping of required length, standard wall/floor mounted fuel with level indicator and piping anddrip proof alternator, self excited, self regulated, screen protected, with excitation system, capable of delivering the rated system output at 415 volts, 3 phase, 0.8 PF, 50 Hz, 4 wire, running at 1500 RPM, conforming to IS-4722- 1968 with voltage regulation+/- 5% of rated voltage from no load to full load. Both the engine and alternator fitted on a common fabricated steel base plate with antivibration mounting engineand alternator both connected to each other by flexible flange coupling and with floor/wall mounted control panel box comprisingof voltmeter ammeter, selector switches, ACB / MCCB / MCB of adequate capacity, indicator lamps duly wired with HRC fuses. The alternator & control panel shall be connected with provided suitable capacity armoured cable and complete with Acoustic enclosure (canopy) made out of 18 SWG CRCA Sheet, sound absorbing material Rockwool of 64 density & 100 mm thick conforming to IS:8183 The resin bonded rockwool covered from inside the canopy by perforated sheet with 3/4 mm holes, sound level not more than 75 dB at a distance of 1 mtr, as per PVCT norms. Erection, commissioning and satisfactory testing as per requirement with first filling of fuel, oil, etc. with guarantee of complete system for One year. & with obtaining all necessary certificate from Electrical Inspector.
306	PLUMBING WORK: Providing and fixing wsh down water closet with flushing cistern with bracket frame and all necessary fittings and accessories. (European type, W.C. Pan) with integral P or S trap including jointing the trap with soil pipe in Cement Mortar 1:1 (1-Cement : 1-fine sand) (Seal and cover to be measured and paid for separately)(A) vitreous China Pattern :(i) in white colour including all accessories and connections. Make: Jaquar, Kohler, Grohe, Cera high end series.
307	Providing and fixing under counter washbasin with single hole for pillar tap with C.I. or M.S. brackets painted white including sutting holes and making good the same but excluding fittings.(A) Vitreous China:(ii) Flat Back washbasin 550 mm x v400mm size. (i) In white colour including all required accessories and connections like bottle trap, waste etc.Make: Jaquar, Kohler, Grohe, Cera high end series.
308	Providing and fixing 600mm x 450mm bevelled edge mirrror of superior glass mounted on 6mm thick A.C. sheet or plywood sheet and fixing to wooden pluge with C.P. brass screws and washers.
309	Providing and fixing stainless steel toilet paper holder.Make: Jaquar, Kohler, Grohe, Cera high end series.
310	Providing and fixing screw down bib taps of following size.(B) Brasschromiumplated screws down Bib Tap including all required accessories and connections. (i) 15mm dia. Make: Jaquar, Kohler, Grohe, Cera high end series.
311	Providing and fixing pillar tap, capstanhead, screw down high pressure with screws, shanks and back nuts. including all required accessories and connections. (i) 15mm dia.Make: Jaquar, Kohler, Grohe, Cera high end series.
312	Providing and fixing Urinal of approved quality including connection with trap and with integral longitudinal flush pipe.(A) Squatingplate patternwhite earthenware 550mm x 300mm. including all required accessories and connections.Make: Jaquar, Kohler, Grohe, Cera high end series.
313	Providing and fixing C.P. ss towel rail comlete with C.P. brass/ ss brackets fixed to wooden plugs with C.P. brass/ ss scews.(B) 600mm x 20mm size.
314	Providing and fixing Kitchen stainless steel sink with C.I/M.S./SS brackets or frame painted white or as per approved by the architect including cutting holes in walls and making good the same including all fittings. (i) 625mm x 445mm x 200mm size.Make: Jaquar, Nirali, Carysil high end series.
315	Providing, fixing and testing 150 mm2 two piece stainless steel jali with cockroach trap over nanhi/multifloor trap/floor trap fixing with cement in proper position etc. complete as directed.
316	Providing and fixing screw down 2-way bib cock of following size. Brass chromium plated 2-way bib cock (i) 15 mm.(Make: Hind ware/cera/jaquar/Grohe) including health faucet, 1.2 mtr long pvc tube and walk hook with all required accessories and connections. Make: Jaquar, Kohler, Grohe, Cera high end series.
317	Supply, installation, testing and commissioning of auto closing concealed push button for urinal flushing with all required accessories and fitting. Make: Jaquar, Kohler, Grohe, Cera high end series.
318	Providing and fixing Angle tap, capstanhead, screw down high pressure with screws, shanks and back nuts.(i) 15mm dia.(Make: Hind ware/cera/jaquar/Grohe) including all required accessories and connections. Make: Jaquar, Kohler, Grohe, Cera high end series.
319	Providing and fixing 450mm Long Braided Hose pipe with M10X1 Nipple, 15mm Nut, O-Ring & Rubber Washer (Suitable for Wash Basin, Kitchen Sink etc.) of approved make and conforming toManufacturers Standards. Make: Jaquar, Kohler, Grohe, Cera high end series.
320	Supply, installation, testing and commissioning of brass chromium plated 4way shower diverter, spout with hand shower provision & 6inch dia wall fixed shower 15/20mm including all fittings, accessories and connections. Make: Jaquar, Grohe, Hindware, Kohler, Cera
321	Supply, storing, installation and testing twin coat hook, fixed to wall / door with concealed CP screws etc. complete. Make: Jaquar, Kohler, Grohe, Hindware, Cera high end series.
322	Providing and fixing of grab bars 300 mm Stainless steel in physically disabled toilet including all necessary fitting, SS Screws & Accessories etc.Complted in all manners and satisfied to of EIC.complete. Make: Jaquar, Kohler, Grohe, Hindware, Cera high end series.
323	Providing and fixing of grab bars Vertical Swing 18-8 S, type-304, 18-gauge (1mm) stainless steel tubing with satin-finish. 1–1/4 (25mm) outside diameter wall mounted in physically disabled toilet including all necessary fitting, SS Screws & Accessories etc.Complted in all manners and satisfied to of EIC.complete. Make: Jaquar, Kohler, Grohe, Hindware, Cera high end series.
324	Providing and Fixing of Stainless Steel Hand Dryer with all required connections and following specifications. Weld-free cover fixed to the base with two safety screws and lock withspecial speedflow key. Aluminium base. Includes silent-blocks to damp mechanical vibrations. Fire resistant plastic UL 94-V0 fan scroll. High-speed motor with safety thermal cut-off.The motor revolutions canbe adjusted manually by the potentiometer. • Aluminium centrifugal double asymmetrical inlet fan wheel. Disconnects automatically after 60 seconds of continuous use. Electronic infrared detection sensor. Adjustable detection by potentiometer(5- 25 cm). Ultra-flat: 10 cm deep (complies with ADA regulations). complete. Make: Jaquar, Kohler, Grohe, Hindware, Cera high end series.
325	Providing and erecting water cooler having storage capacity 80Ltr. & cooling capacity 40 Ltr.per hour @ an ambient temp of 450C. The outlet temp. of the water should drop by 150 C within a hour, The water cooler should be comprising of hermetically sealed compressor, fan motor, condensing unit, water tank surrounded by evaporating coil, thermostats, relay etc. complete with necessary inlet & outlet connection. The body of water cooler will be made from Stainless Steel.
326	Supplying & erecting 5 stage single reverse osmosis water purification system with M.S. powder coated frame, pre filter housing with \"O\" ring pre sediment filter GAC filter, carbon filter suitable buster DC pump capacity 80 psi, mention with 40 Osg inline type post carbon filter auto low & high pressure switches with following size of storage tank & LPH capacity & erected as directed with one year comprehensive maintenance guarantee. [B] 25 Ltr / Hr with 30 Ltr. S.S. Pressure Tank
327	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed work, including cutting chases and making good the walls etc. For Cold Water Lines ( Domestic & Hot) (Inside Toilet)(Make:Astral,Ashirwad,Finolex) 15 mm nominal outer dia Pipes ( SDR 11 )
328	:Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed work, including cutting chases and making good the walls etc. For Cold Water Lines ( Domestic & Hot) (Inside Toilet)(Make:Astral,Ashirwad,Finolex) 20 mm nominal outer dia Pipes ( SDR 11 )
329	:Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed work, including cutting chases and making good the walls etc. For Cold Water Lines ( Domestic & Hot) (Inside Toilet)(Make:Astral,Ashirwad,Finolex)25 mm nominal outer dia Pipes ( SDR 11 )
330	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Exposed on WallFor Cold Water Lines ( Domestic & Hot ) (In shaft & Terrace & Exposed On wall)(Make:Astral,Ashirwad,Finolex) 20 mm nominal outer dia Pipes ( SDR 11 )
331	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Exposed on WallFor Cold Water Lines ( Domestic & Hot ) (In shaft & Terrace & Exposed On wall)(Make:Astral,Ashirwad,Finolex) 25 mm nominal outer dia Pipes ( SDR 11 )
332	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Exposed on WallFor Cold Water Lines ( Domestic & Hot ) (In shaft & Terrace & Exposed On wall)(Make:Astral,Ashirwad,Finolex) 32 mm nominal outer dia Pipes ( SDR 11 )
333	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Exposed on WallFor Cold Water Lines ( Domestic & Hot ) (In shaft & Terrace & Exposed On wall)(Make:Astral,Ashirwad,Finolex) 40 mm nominal outer dia Pipes ( SDR 11 )
334	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Exposed on WallFor Cold Water Lines ( Domestic & Hot ) (In shaft & Terrace & Exposed On wall)(Make:Astral,Ashirwad,Finolex) 50 mm nominal outer dia Pipes ( SDR 11 )
335	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 15 mm nominal dia Pipes
336	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.20 mm nominal dia Pipes
337	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.25 mm nominal dia Pipes
338	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.32 mm nominal dia Pipes
339	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.40 mm nominal dia Pipes
340	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.50 mm nominal dia Pipes
341	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.65 mm nominal dia Pipes
342	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.80 mm nominal dia Pipes
343	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.100 mm nominal dia Pipes
344	Providing, fixing, jointing and testing, heavy quality CPVC ball valve single/doublepiece designed of approved make, including unions, nuts, bolts, washers, etc. complete, as per I.S 5212 approved by the Engineer-in-charge for water supply lines of the following nominal bore (NB) size: 20mm diameter. Make:ZOLOTO/VTC/SANT
345	Providing, fixing, jointing and testing, heavy quality cast steel / Brass ball valve single/doublepiece designed of approved make, including flanges / unions, nuts, bolts, washers, etc. complete, as per I.S 5212 approved by the Engineer-in-charge for water supply lines of the following nominal bore (NB) size: 25mm diameter. Make:ZOLOTO/VTC/SANT
346	Providing, fixing, jointing and testing, heavy quality CPVC ball valve single/doublepiece designed of approved make, including unions, nuts, bolts, washers, etc. complete, as per I.S 5212 approved by the Engineer-in-charge for water supply lines of the following nominal bore (NB) size: 25mm diameter. Make:ZOLOTO/VTC/SANT
347	Providing, fixing, jointing and testing, heavy quality cast steel / Brass ball valve single/doublepiece designed of approved make, including flanges / unions, nuts, bolts, washers, etc. complete, as per I.S 5212 approved by the Engineer-in-charge for water supply lines of the following nominal bore (NB) size: 32mm diameter (Make:ZOLOTO/VTC/SANT)
348	Providing, fixing, jointing and testing, heavy quality CPVC ball valve single/doublepiece designed of approved make, including unions, nuts, bolts, washers, etc. complete, as per I.S 5212 approved by the Engineer-in-charge for water supply lines of the following nominal bore (NB) size: 32mm diameter. Make:ZOLOTO/VTC/SANT
349	Providing, fixing, jointing and testing, heavy quality cast steel / Brass ball valve single/doublepiece designed of approved make, including flanges / unions, nuts, bolts, washers, etc. complete, as per I.S 5212 approved by the Engineer-in-charge for water supply lines of the following nominal bore (NB) size: 40mm diameter (Make:ZOLOTO/VTC/SANT)
350	Providing, fixing, jointing and testing, heavy quality cast steel / Brass ball valve single/doublepiece designed of approved make, including flanges / unions, nuts, bolts, washers, etc. complete, as per I.S 5212 approved by the Engineer-in-charge for water supply lines of the following nominal bore (NB) size: 50mm diameter (Make:ZOLOTO/VTC/SANT)
351	Providing, fixing, jointing and testing, heavy quality cast steel / Brass ball valve single/doublepiece designed of approved make, including flanges / unions, nuts, bolts, washers, etc. complete, as per I.S 5212 approved by the Engineer-in-charge for water supply lines of the following nominal bore (NB) size: 65mm diameter (Make:ZOLOTO/VTC/SANT)
352	Providing, fixing, jointing and testing, heavy quality cast steel / Brass ball valve single/doublepiece designed of approved make, including flanges / unions, nuts, bolts, washers, etc. complete, as per I.S 5212 approved by the Engineer-in-charge for water supply lines of the following nominal bore (NB) size: 80mm diameter (Make:ZOLOTO/VTC/SANT)
353	Providing, fixing, jointing and testing, heavy quality cast steel / Brass Non-return valve single/doublepiece designed of approved make, including flanges / unions, nuts, bolts, washers, etc. complete, as per I.S 5212 approved by the Engineer-in-charge for water supply lines of the following nominal bore (NB) size: 25mm diameter (Make:ZOLOTO/VTC/SANT)
354	Providing, fixing, jointing and testing, heavy quality cast steel / Brass Non-return valve single/doublepiece designed of approved make, including flanges / unions, nuts, bolts, washers, etc. complete, as per I.S 5212 approved by the Engineer-in-charge for water supply lines of the following nominal bore (NB) size: 32mm diameter (Make:ZOLOTO/VTC/SANT)
355	Providing, fixing, jointing and testing, heavy quality cast steel / Brass Non-return valve single/doublepiece designed of approved make, including flanges / unions, nuts, bolts, washers, etc. complete, as per I.S 5212 approved by the Engineer-in-charge for water supply lines of the following nominal bore (NB) size: 40mm diameter (Make:ZOLOTO/VTC/SANT)
356	Providing, fixing, jointing and testing, heavy quality cast steel / Brass Non-return valve single/doublepiece designed of approved make, including flanges / unions, nuts, bolts, washers, etc. complete, as per I.S 5212 approved by the Engineer-in-charge for water supply lines of the following nominal bore (NB) size: 50mm diameter (Make:ZOLOTO/VTC/SANT)
357	Providing and supplying ISI mark CI D/F Butterfly Valves as per IS:13095 (Latest Edition) of PN 10 and 50 mm diameter including all taxes, insurance, transportation, freight charges, octroi, inspection charges, loading, unloading, conveyance to departmental stores, stacking etc. complete.
358	Providing and supplying ISI mark CI D/F Butterfly Valves as per IS:13095 (Latest Edition) of PN 10 and 100 mm diameter including all taxes, insurance, transportation, freight charges, octroi, inspection charges, loading, unloading, conveyance to departmental stores, stacking etc. complete.
359	Supplying, Installing, testing & Commissioning in position electrically operated level sensor based 32mm diameter solenoid valve with level electroeds for water tank inlet as shown in drawing & specified in specifiaction including weather proof housing,control panel, isolator, cables, accessories etc complete.Item including all accessories for satisfactory installation complete. Any standard ISI make.
360	Preparing structural design of RCC Under Ground / Partially under ground /above high ground level Reservoir and constructing of required capacityas per relevant I.S. standards in M30 concrete gradewith HYSD Fe 500D reinforcement and constructing the same, including excavation in all types of soil strata (including rock) including shoring strutting if required, for loose soil / to protect from collapse, casting 100 mm thick P.C.C. levelling course in M-15, Refilling the pit with proper soil and disposing of the surplus stuff at all lead. Including cement plaster in CM 1:2 with approved water proofing compound to all over inside container (i.e. walls, base, top slab/dome bottom etc. all). Including Soil testing. Including all types of labour and material charges of lowering, laying, erecting / hosting and jointing of pipe assembly to inlet, outlet overflow, washout and bye pass arrangement as per hydraulic design. Providing and fixing accessories, CI Manhole frame and cover, water level indicator, adequate cowl type ventilators or lantern type ventilator with stainless steel jail. RCC chambers for valves. Providing and applying three coats of cement paint / snowcem to the out side face of structure. It also includes satisfactory water tightness test as per relevant I.S. code and painting name of scheme and capacity on the tank as per direction of engineer in charge.
361	Supply Instalation,Testing,Commissioning of packaged Water HeatPump made with water resistant materials and capable for outdoorinstallation. The Heat Pump System should have fully closed scroll compressor. Thecompressors should be Shall and tube heat exchanger typeprofile optimized for eco friendly R410A refrigerant. The unit must have rubber supports. The plant heat exchanger must have copper brazed plate type with cover plates, plates and connections in AISI 316 stainlesssteel. The unit must be equipped with a thermostaticexpansion valve. The electric panel must have operator selector modei.e. summer/winter working modes. The power supply to this unit mustbe 415V±10/3phase/50Hz. The unit must have microprocessor based controlsystem. The operating ambient conditions should be between 45°C and10°C. Heat pump shall have LCD display control panel with built in diagnostic and troubleshooting information and with scroll type compressor . with inbuilt shell and tube type heat exchanger. Suitable for electric supply of 415 volts & 3N~ 50 hz. The heat pump shall have an in-built facility to start /stop depending on variation in demand at different periods.Heat pump heating output capacity : 39kW. Rated cooling capacity : 11kW COP : 4.6. Rated hot water output temp. : 55°C. Maximum hot water output temp. : 60°C. Nominal Input Power - 8.47 KW. Design, Supply, installation, testing&commissioning of MS horizontal hot water storage tank (Capacity 3000 Ltrs) suitable for 5 bar working pressure. Tank shall be insulated as per specification, including 24 gauge aluminum cladding.With internal epoxy coating and outer side 50mm thick insulation. Instruments, piping accessories, valves, strainers, Controls for Heat pump to storage tank, including temperature controllers,Glycerin filled pressure gauges, spring loaded safety relief valve etc., asrequired, complete for each Heat pump.
362	Providing, laying and jointing in true line and level 40mm diameter U.P.V.C (Type B) conforming to IS 13592-1992 with one end plain and other end socketed with rubber ring, & fittings conforming to ISI 14735-1999 of approved make for drainage system pipe line,pipe shall be jointed with each other with rubber lubricant, pipe shall be concealed in walls as directed including necessary fittings such as bends, shoes etc. including testing of pipes and joints and jointed with adhesive solvent cement including cost of all materials. (Make: prince/ supreme / astral / finolex)
363	Providing, laying and jointing in true line and level 50mm diameter U.P.V.C (Type B) conforming to IS 13592-1992 with one end plain and other end socketed with rubber ring, & fittings conforming to ISI 14735-1999 of approved make for drainage system pipe line,pipe shall be jointed with each other with rubber lubricant, pipe shall be concealed in walls as directed including necessary fittings such as bends, shoes etc. including testing of pipes and joints and jointed with adhesive solvent cement including cost of all materials. (Make: prince/ supreme / astral / finolex)
364	Providing, laying and jointing in true line and level 75mm diameter U.P.V.C (Type B) conforming to IS 13592-1992 with one end plain and other end socketed with rubber ring, & fittings conforming to ISI 14735-1999 of approved make for drainage system pipe line,pipe shall be jointed with each other with rubber lubricant, pipe shall be concealed in walls as directed including necessary fittings such as bends, shoes etc. including testing of pipes and joints and jointed with adhesive solvent cement including cost of all materials. (Make: prince/ supreme / astral / finolex)
365	Providing, laying and jointing in true line and level 110mm diameter U.P.V.C (Type B) conforming to IS 13592-1992 with one end plain and other end socketed with rubber ring, & fittings conforming to ISI 14735-1999 of approved make for drainage system pipe line,pipe shall be jointed with each other with rubber lubricant, pipe shall be fixed on wall using of PVC clamp of the size 110 mm diameter x 149 mm length x 145 mm height at every 2000 mm center to center or shall be concealed in walls as directed including necessary fittings such as bends, shoes etc. including testing of pipes and joints and jointed with adhesive solvent cement including cost of all materials. (Make: prince/ supreme / astral / finolex)
366	Providing, laying and jointing in true line and level 150mm diameter U.P.V.C (Type B) conforming to IS 13592-1992 with one end plain and other end socketed with rubber ring, & fittings conforming to ISI 14735-1999 of approved make for drainage system pipe line,pipe shall be jointed with each other with rubber lubricant, pipe shall be fixed on wall using of PVC clamp of the size 110 mm diameter x 149 mm length x 145 mm height at every 2000 mm center to center or shall be concealed in walls as directed including necessary fittings such as bends, shoes etc. including testing of pipes and joints and jointed with adhesive solvent cement including cost of all materials. (Make: prince/ supreme / astral / finolex)
367	Providing, fixing and testing PVC Deep seal P-Trap of110 X 110 mm dia diameter, with necessary distance piece of 75mm dia pipe and 150 x 150mm heavy duty PVC three piece grating, making necessary holes and cutting in Slab/Walls, etc complete as per engineer in charge. (Make: prince/ supreme / astral / finolex)
368	Providing, fixing and testing PVC Height Riser with wings of110 X 50 X 40 mm dia diameter, with necessary suported accessories, making necessary holes and cutting in Slab/Walls, etc complete as per engineer in charge. (Make: prince/ supreme / astral / finolex)
369	Providing and supplying of Class SN8 Structured Wall polyethelene Piping systems (Pipe with online/offline coupler and elastomeric sealing ring) with non-smooth External Annular Corrugated and Smooth Internal Surfaces (Double Wall) for non-pressure underground Sewerage & Drainage application as per EN:13476-3 including all local and central taxes, transportation, freight charges, octroi, inspection charges, loading, unloading, conveyance to the departmental stores etc. complete.(ID 150 mm diameter) Make: Astral, Supreme, Finolex, Prince
370	Providing and supplying of Class SN8 Structured Wall polyethelene Piping systems (Pipe with online/offline coupler and elastomeric sealing ring) with non-smooth External Annular Corrugated and Smooth Internal Surfaces (Double Wall) for non-pressure underground Sewerage & Drainage application as per EN:13476-3 including all local and central taxes, transportation, freight charges, octroi, inspection charges, loading, unloading, conveyance to the departmental stores etc. complete.(ID 200 mm diameter). Make: Astral, Supreme, Finolex, Prince
371	Excavation for foundation/utility services upto 1.5 m depth including sortingoutandstacking of useful materials anddisposing off the excavated stuff with all lead and lift.(E)HardRock
372	Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm. in depth consolidating each depositedlayer by ramming and watering. (Ramping by manual or mechanical means)
373	Providing and fixing, best Indian make 1st quality, salt glazed PVC Sewer (intercepting) trap, of 150 mm. x 150 mm. size with cleaning eye cap and metal stopper chain, set in CC 1:2:4 etc., complete in last manhole including vent / fresh air pipe.
374	Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 150 x 100 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
375	Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 250 mm dia. R.C.C. pipe
376	Providing and fixing factory made precast RCC perforated drain covers, having concrete of strength not less than M-25, of size 1000 x 450x50 mm, reinforced with 8 mm dia four nos longitudinal & 9 nos cross sectional T.M.T. hoop bars, including providing 50 mm dia perforations @ 100 to 125 mm c/c, including providing edge binding with M.S. flats of size 50 mm x 1.6 mm complete, all as per direction of Engineerin- charge.
377	Constructing brick masonry manhole in cement mortar 1:4 (1cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominalsize), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
378	Providing & Fixing of factory made Precast Chamber, having size (in to in) of 800 mm (L) X 800 mm (B) X Height : 800 mm T-25 load carrying capacity - 10 T Axle Load - 5 T Wheel Load, confirming to IS requirements, having High Performance Self Compacting Concrete of M-40 cylinder strength/M-50 cube strength & use ofFe 500 D reinforcement. The contractor shall prepare & provide the base using PCC/Foundation concrete as a levelling courseas recommended by the consultant. The precast Chamber unit should consist of special in built insert of suitable load carrying capacity at appropriate location for fixing De-shackle (Hanging hole) for safe & fast mechanical installation.Cut out holes hole should be providedfor utility connectionas per the requirement.The Precast cover having size 944 x 944 X 120 mm thick , designed forT-25 load carrying capacity - 10 T Axle Load - 5 T Wheel Load, confirming to IS requirements, having High Performance Self Compacting Concrete of M-40 cylinder strength/M-50 cube strength & use of Fe 500D reinforcement.The lid may have in build specially designed lifting inserts of appropriate load carrying capacity & fixed at specific location to avoid the tilting of the lid for safe & fast installation.In no case the casting shall be allowed to be prepared at site. It should be casted in the stringent atmospheric & pre-defined condition, as per approved QAP as by Engineer In charge,including making cut-outs, core cutting for ducts. Brand: Fuji Silvertech, and equivalent.Make: Fuji Silvertech or equivalent
379	Providing & Fixing of factory made Precast Chamber, having size (in to in) of 1000 mm (L) X 1000 mm (B) X Height: 1000, mm T-25 load carrying capacity - 10 T Axle Load - 5 T Wheel Load, confirming to Japanese Industrial Standards (JIS) & meeting IS requirements, having High Performance Self Compacting Concrete of M-40 cylinder strength/M-50 cube strength & Fe 500 /Fe 500 D shall be used for reinforcement. The contractor shall prepare & provide the base using PCC/Foundation concrete as a levelling course as per drawing / as recommended by the consultant depending upon the foundation soil strata. The precast Chamber unit should consist of special in built insert of suitable load carrying capacity at appropriate location for fixing De-shackle (Hanging hole) for safe & fast mechanical installation.Hole should be provided at site (No Factory) for connection at the waffle side of chamber as per the site requirement.The Precast cover having size 1144 x 1144 X 150 mm thick, designed forT-25 load carrying capacity - 10 T Axle Load - 5 T Wheel Load, confirming to Japanese Industrial Standards (JIS) & meeting IS requirements, having High Performance Self Compacting Concrete of M-40 cylinder strength/M-50 cube strength & Fe 500 / 500D shall be used for reinforcement. Cover should have conical shape of 50 mm to 30 mm respectively for storm water intake. The lid may have in build specially designed lifting inserts of appropriate load carrying capacity & fixed at specific location to avoid the tilting of the lid for safe & fast installation.In no case the casting shall be allowed to be prepared at site. It should be casted in the stringent atmospheric & pre-defined condition, as per approved QAP as by Engineer In charge. Make: Fuji Silvertech or equivalent
380	Providing & Fixing of factory made Precast Chamber, having size (in to in) of 1000 mm (L) X 1000 mm (B) X Height: 1200, mm T-25 load carrying capacity - 10 T Axle Load - 5 T Wheel Load, confirming to Japanese Industrial Standards (JIS) & meeting IS requirements, having High Performance Self Compacting Concrete of M-40 cylinder strength/M-50 cube strength & Fe 500 /Fe 500 D shall be used for reinforcement. The contractor shall prepare & provide the base using PCC/Foundation concrete as a levelling course as per drawing / as recommended by the consultant depending upon the foundation soil strata. The precast Chamber unit should consist of special in built insert of suitable load carrying capacity at appropriate location for fixing De-shackle (Hanging hole) for safe & fast mechanical installation.Hole should be provided at site (No Factory) for connection at the waffle side of chamber as per the site requirement.The Precast cover having size 1144 x 1144 X 150 mm thick, designed forT-25 load carrying capacity - 10 T Axle Load - 5 T Wheel Load, confirming to Japanese Industrial Standards (JIS) & meeting IS requirements, having High Performance Self Compacting Concrete of M-40 cylinder strength/M-50 cube strength & Fe 500 / 500D shall be used for reinforcement. Cover should have conical shape of 50 mm to 30 mm respectively for storm water intake. The lid may have in build specially designed lifting inserts of appropriate load carrying capacity & fixed at specific location to avoid the tilting of the lid for safe & fast installation.In no case the casting shall be allowed to be prepared at site. It should be casted in the stringent atmospheric & pre-defined condition, as per approved QAP as by Engineer In charge. Make: Fuji Silvertech or equivalent
381	Providing and fixing C.I. cover with frame (Medium duty) 500 mm internal diameter, total weight of cover and frame to be not less than 116 kg (weight of cover 58 kg and weight of frame 58 kg.
382	Providing, laying and jointing in true line and level 110 mm diameter U.P.V.C (Type A) conforming to IS 13592-1992 with one end plain and other end socketed with rubber ring, & fittings conforming to ISI 14735-1999 of approved make for drainage system pipe line,pipe shall be jointed with each other with rubber lubricant, pipe shall be fixed on wall using of PVC clamp of the size 110 mm diameter x 149 mm length x 145 mm height at every 2000 mm center to center or shall be concealed in walls as directed including necessary fittings such as bends, shoes etc. including testing of pipes and joints and jointed with adhesive solvent cement including cost of all materials. Make: Astral, Supreme, Finolex, Prince
383	Providing, Fixing, Installation and Testing of 100mm rainwater outlets 2HP-2W/3HP-2W/ 4HP-2W* are to be ACO Building Drainage HP Two-Way screw outlets with locked flat grating supplied by ACO Building DrainageSG17 5TE. All components to be manufactured from grade LM6 aluminium alloy to BS 1490/ gun-metal to BS EN 1982. complete as per site engineer in charge. Make: Astral, Supreme, Finolex, Prince
384	Providing and fixing, PVC cowl, 110mm diameter on PVC ventilating pipes and verticalsfor soil and waste Pipes at top level / terrace level, as specified and required, etc. complete. Make: Astral, Supreme, Finolex, Prince
385	Providing, laying and jointing in true line and level 150 mm diameter U.P.V.C (Type A) conforming to IS 13592-1992 with one end plain and other end socketed with rubber ring, & fittings conforming to ISI 14735-1999 of approved make for drainage system pipe line,pipe shall be jointed with each other with rubber lubricant, pipe shall be fixed on wall using of PVC clamp of the size 150 mm diameter x 149 mm length x 145 mm height at every 2000 mm center to center or shall be concealed in walls as directed including necessary fittings such as bends, shoes etc. including testing of pipes and joints and jointed with adhesive solvent cement including cost of all materials. Make: Astral, Supreme, Finolex, Prince
386	Providing, Fixing, Installation and Testing of 150mm rainwater outlets 2HP-2W/3HP-2W/ 4HP-2W* are to be ACO Building Drainage HP Two-Way screw outlets with locked flat grating supplied by ACO Building DrainageSG17 5TE. All components to be manufactured from grade LM6 aluminium alloy to BS 1490/ gun-metal to BS EN 1982. complete as per site engineer in charge. Make: Astral, Supreme, Finolex, Prince
387	Providing and fixing, PVC cowl, 150mm diameter on PVC ventilating pipes and verticalsfor soil and waste Pipes at top level / terrace level, as specified and required, etc. complete. Make: Astral, Supreme, Finolex, Prince
388	Supply, installation, testing and commissioning of one no. 35KLD Sewage Treatment Plant, underground (for overall site) with all required civil work including labour and material with all necessary equipment and accessories. Contractor must consider the supervision for the plant working for minimum twice in a month for at least 5 years. Equipments make must be standard and contractor has to get the approval of the make from the consultant.
389	Supply, installation, testing and commissioning of one no. 5KLD Effluent Treatment Plant, underground (for Laboratory Water Disposal) with all required civil work including labour and material with all necessary equipment and accessories. Contractor must consider the supervision for the plant working for minimum twice in a month for at least 5 years. Equipments make must be standard and contractor has to get the approval of the make from the consultant.
390	Providing and Installing KESSEL-Grease Separator EasyClean ground Standard NS 10 NS 10 based on Euro-Norm EN 1825-1. Manufactured from Polyethylene.Art No-93010/120B, HSN CODE-84212190. For underground installation below the frost zone, with integrated sludge trap, polyethylene upper section which is vertically adjustable, rotatable and tiliable up to 5 degrees, cast iron cover in load class B 12.5 ton based on EN 124, odor tight, removal key included. Installation depth 755 - 1.190 mm. Sludge trap capacity: upto 200liter. Total separator cpacity: upto 500liter. tanks / cisterns may be installed in groundwater up to the top of the tank body. Certification Z-54.1-440. Delivered complately assambled. Manufacturer: KESSEL, ACO or Equivalent. Contractor must consider themaintenance for at least 5 years. Equipments make must be standard and contractor has to get the approval of the make from the consultant.
391	Supply, fixing and jointing of heavy class GI puddle flange pipes epoxy coated, 50 mm dia and minimum 400 mm long clear ends outside the RCC surface, and fixed in underground sumps, water tanks etc. complete, with end joints either screwed / flangedas required with endcaps / plugs complete as per the requirement of E-i-C (Local Make)
392	Supply, fixing and jointing of heavy class GI puddle flange pipes epoxy coated, 80 mm dia and minimum 400 mm long clear ends outside the RCC surface, and fixed in underground sumps, water tanks etc. complete, with end joints either screwed / flangedas required with endcaps / plugs complete as per the requirement of E-i-C (Local Make)
393	Supply, fixing and jointing of heavy class GI puddle flange pipes epoxy coated, 100 mm dia and minimum 400 mm long clear ends outside the RCC surface, and fixed in underground sumps, water tanks etc. complete, with end joints either screwed / flangedas required with endcaps / plugs complete as per the requirement of E-i-C (Local Make)
394	Supply, fixing and jointing of heavy class GI puddle flange pipes epoxy coated, 150 mm dia and minimum 400 mm long clear ends outside the RCC surface, and fixed in underground sumps, water tanks etc. complete, with end joints either screwed / flangedas required with endcaps / plugs complete as per the requirement of E-i-C (Local Make)
395	Providing and fixing electronic type level indicator for water tanks mounting in panel with level display, alarm (level low or high), and manual reset for alarm, potential free set point contacts etc. complete with electrical wiring to probes and all accessories complete the work. Provision to connect to the building Automation system or pump controllerthrough a suitable port.(Make: Wilo)
396	Horizontal multistage, Centrifugal clear water pumps with SS-304 Casing, S.S 304 Impeller, SS-304 Shaft, SS-304 Base and Head TEFC motor based CI with CED coated (with Mechanical seal) Vendor to submit performance curves and technical catalogue of the proposed model for review and information. (Company Fitted System & System Test Certificate require for the same). Electrical Starter panels complete with O/L Relay with Single phasing preventer feature, earth leakage relay, ON-OFF and Trip Indicating lamps, interlocking, cascade operation, working / standby selection, etc. suitablefor the motor H.P. as specified below and with provision for manual auto on/off selector switch complete as required. Pre-charged diaphragm pressure vessel with MS connection, connected to outlet header with necessary connection, gaskets, isolating valves, nuts/bolts etc. complete (size of pressure vessel shall be 100 litters (approx.) or as per manufacturer recommendation). Set of accessories such as M.S. Zinc Coated headers for suction and discharge, control valves, non return valves,Foot valve with Strainer, pressure switches, pressure gauge, inter connecting power and control cabling etc. complete.. As per complete company Fitted and tested system Capacity per pump-1.66 LPS [6 m3/hour],System Flow - 3.32.78LPS [12 m3/hour],Head:-12 Meter 2 Nos. Pumps (1 Working + 1standby) Make: Wilo, Kirloskar, Grundfos
397	Supply of Submersible single stage single entry pumps connected to submersible motor (The motor shall be watertight according to IEC class IP 68, and incorporate class F insulation materials to withstand a continuous operating temperature of 155 deg C) for 415 + 10% volts, 3 phase, 50 cycles A.C. power supply with Double mechanical seal, pump connector unit with rubber diaphragm and bend, electrical panel with in built level controller with operational mode as one pump working at low level, both pumps at high level with a hooter alarm and cut off at dry level as determined. The pump shall be provided with a lifting devise of pull chain or guide rail. (Pumps shall be installed in a set of two pumps One working and One standby, with cascade operation).Pumps suitable to handle solids upto 40 mm size with C.I. body, SS304 impeller & SS shaft with 10 mtrs cable, double mechanical seal.Electrical Starter panels complete with Over load & Under Current Relay with Single phasing preventer feature,ON-OFF and Trip Indicating lamps, contactors contacts for BMS System, interlocking, level controller with operational mode as one pump working at low level, both pumps at high level with a hooter alarm and cut off at dry level, cascade operation, working / standby slelction, etc.including with discharge valve and NRV, suitablefor the motor H.P. as specified below. As per complete company Fitted and tested system Capacity per pump-1.39 LPS [5 m3/hour],System Flow - 2.78LPS [10 m3/hour],Head:-12Meter 2 Nos. Pumps (1 Working + 1standby). Make: Wilo, Kirloskar, Grundfos
398	Supply, installation, testing & commissioning of Submersible Open well single stage single entry pumps with C.I Casing, C.I Impeller and SS Body SS-304 Shaft,connected to TEFC submersible motor for 415 + 10% volts, 1 phase, 50 cycles A.C. power supply with mechanical seal, pump connector unit with rubber diaphragm and bend, vertical discharge pipe, electrical panel with in built level controller with operational mode as pump working at low level, as well pump at high level with a hooter alarm and cut off at dry level as determined. The pump shall be provided with a lifting devise of pull chain/guide rail & G.I. heavy class rising main of 1.0 m length including interconnecting piping, valves (Ball Valve / Butterfly), Non return valves (GM/CI) 15 m cable etc. as per requirement complete in all respects. (Pumps shall be installed in a set of One pump operation).Electrical Starter panels complete with O/L Relay with Single phasing preventer feature, earth leakage relay, ON-OFF and Trip Indicating lamps, contactors contacts for Building Automation System, interlocking, level controller with operational mode as one pump working at low level, both pumps at high level with a hooter alarm and cut off at dry level, cascade operation, working / standby slelction, etc. suitablefor the motor H.P. as specified below and with provision for remote P.B. on/off complete as required. The on/off operations for all pumps shall be available on central BMS system Capacity per pump-1.11 LPS [4 m3/hour],System Flow - 2.22LPS [8 m3/hour],Head:-25-30 Meter 2 Nos. Pumps (1 Working + 1standby). Make: Wilo, Kirloskar, Grundfos
399	Supply of Submersible single stage single entry pumps connected to submersible motor (The motor shall be watertight according to IEC class IP 68, and incorporate class F insulation materials to withstand a continuous operating temperature of 155 deg C) for 415 + 10% volts, 3 phase, 50 cycles A.C. power supply with Double mechanical seal, pump connector unit with rubber diaphragm and bend, electrical panel with in built level controller with operational mode as one pump working at low level, both pumps at high level with a hooter alarm and cut off at dry level as determined. The pump shall be provided with a lifting devise of pull chain or guide rail. (Pumps shall be installed in a set of two pumps One working and One standby, with cascade operation). (Pumps suitable to handle solids up to 40 mm size with C.I. body, SS304 impeller & SS shaft with 10 mtrs cable, double mechanical seal). Electrical Starter panels complete with Over load & Under Current Relay with Single phasing preventer feature,ON-OFF and Trip Indicating lamps, contactors contacts for BMS System, interlocking, level controller with operational mode as one pump working at low level, both pumps at high level with a hooter alarm and cut off at dry level, cascade operation, working / standby selection, etc. suitablefor the motor H.P. as specified below. Capacity/Flow Rate -1.39 LPS (5.0 M3/Hr) Each Pump. Head - 8.0 m. 1 Set = 2 Nos. pump (1 working+1 standby), cascade operation. Approx. Elec. Load. - 1.5 KW each pump. RPM- 2900. MOC- C.I Casing / SS 304 Impeller / S.S. Shaft
400	Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-in-charge, upto 90 metre depth below ground level. All types of soil. 300 mm dia
401	Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, beyond 90 metre & upto 150 metre depth below ground level. All types of soil. 300 mm dia
402	Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 100 mm nominal size dia
403	Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 150 mm nominal size dia
404	Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 100 mm nominal size dia
405	Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.
406	Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.
407	Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineerincharge.
408	Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge.
409	Development of tube well in accordance with IS : 2800 (part I) and IS:11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by \"V\" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.
410	FIRE FIGHTING WORK: Providing, laying, testing & commissioning of 25 mm diameter \"C\" class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :
411	Providing, laying, testing & commissioning of 32 mm diameter \"C\" class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :
412	Providing, laying, testing & commissioning of 40 mm diameter \"C\" class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :
413	Providing, laying, testing & commissioning of 50 mm diameter \"C\" class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :
414	Providing, laying, testing & commissioning of 65 mm diameter \"C\" class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :
415	Providing, laying, testing & commissioning of 80 mm diameter \"C\" class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :
416	Providing, laying, testing & commissioning of 100 mm diameter \"C\" class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required
417	Providing and fixing 80 mm dia cast iron butterfly valve complete with epoxy coated disc, carbon steel shaft and lever actuator including flanges and nut bolts etc complete as per I.S 13095 of PN16 rating. for isolation
418	Providing and fixing 100 mm dia cast iron butterfly valve complete with epoxy coated disc, carbon steel shaft and lever actuator including flanges and nut bolts etc complete as per I.S 13095 of PN16 rating. for isolation
419	Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required :
420	Supplying and fixing first-aid 30 meter long Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585. 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket.
421	Supplying and fixing first-aid 40 meter long Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585. 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket.
422	Providing and fixing of weather proof hose cabinet fabricated from 16g MS sheet with full glass door and locking arrangement, suitable to accommodate 2 nos. 15m long 63 mm dia hose, and one no. branch pipe with nozzle. The cabinet shall be painted withtwocoats of \"Fire red\" enamel paint over twocoats ofZinc Cromate primerincluding \"Fire Hose\" written on front including suitably mounted on a raised masonry platform as required. (Approx. 0.75m x 0.6m x 0.25m).
423	Supplying and fixing Gun Metal 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required :
424	Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required as per approved make.
425	Supplying and fixing of 2-way fire brigade connection to static tank (Draw out connection) of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required :
426	Providing & fixing Fire pump ON/OFF switch including all related fitting accessories as per engineer in charge.
427	ABC Powdertype fire extinguisher of 6 Kgs. Capacity, with initial filling in brand new cylinder with powder coated finish, fitted with Gun metal union, high pressure gas cartridge, discharge hose, wall mounting bracket etc. complete, confirming to IS:15683
428	Supply and installation of fire man\"s axe.
429	Providing, fixing, testing & commissioning of 15mm dia quartzoidbulbtypesprinklersofrating68degree centigrade with required accessories : Pendent Sprinkler
430	Providing, fixing, testing & commissioning of 15mm dia quartzoidbulbtypesprinklersofrating68degree centigrade with required accessories :Upright Sprinkler
431	Providing, fixing, testing & commissioning of 15mm dia quartzoidbulbtypesprinklersofrating68degree centigrade with required accessories :Horizontal side wall sprinkler
432	Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.
433	Providing& fixingflowswitchinfollowingsizesM.S. pipe including connection etc as required. 100mm dia
434	Providing laying, testing & commissioning of \"B\" class heavy duty G.I Pipe conforming to IS 1239 i/c fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including welding, excavation & providing cement concrete blocks as supports, anticorrosive treatment with coaltar/asphalt tape as per IS 10221, refilling the trench etc. of following sizes complete as required. Pipe Size: 80mm diameter
435	Providing laying, testing & commissioning of \"C\" class heavy duty G.I Pipe conforming to IS 1239/3589 i/c fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including welding, excavation & providing cement concrete blocks as supports, anticorrosive treatment with coaltar/asphalt tape as per IS 10221, refilling the trench etc. of following sizes complete as required. Pipe Size: 100mm diameter
436	Providing laying, testing & commissioning of \"C\" class heavy duty G.I Pipe conforming to IS 1239/3589 i/c fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including welding, excavation & providing cement concrete blocks as supports, anticorrosive treatment with coaltar/asphalt tape as per IS 10221, refilling the trench etc. of following sizes complete as required. Pipe Size: 150mm diameter
437	Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required : 2 way-100 mm dia M.S. Pipe
438	Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required : 4 way-100 mm dia M.S. Pipe
439	Providing and fixing 150 mm dia cast iron butterfly valve complete with epoxy coated disc, carbon steel shaft and lever actuator including flanges and nut bolts etc complete as per I.S 13095 of PN16 rating. for isolation
440	Providing, installation, testing and commissioning of 100 mm diameter non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required :
441	Providing, installation, testing and commissioning of 150 mm diameter non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required :
442	Providing, installation, testing and commissioning of 150 mm diameter stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange.
443	Providing, installation, testing and commissioning of 100 mm diameter Neoprene based flexible connectors shall be of the single- or double-sphere molded joint configuration and shall meet specifications of the Rubber Expansion Joint Division.
444	Providing, installation, testing and commissioning of 150 mm diameter Neoprene based flexible pump connectors shall be of the single- or double-sphere molded joint configuration and shall meet specifications of the Rubber Expansion Joint Division. Maximum Pressure: 225 PSIG based on 170° F operating temperature.
445	Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and painting with synthetic enamel paint of approved shade as required.
446	Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as required. (contractor to provide detail calculations for orifice plate selection)
447	Providing, fixing, testing & commissioning of installation control valve of cast iron body, brass/bronze working parts comprising of water motor alarm, bronze seat clapper, clapper arm and hydraulically driven mechanical gong bell to sound continuous alarm when the wet riser/sprinkler system activates, pressure gauges, emergency releases, strainer, pressure switch, cock valve complete with drain valve and bypass, test control box, ball valves, MS pipe of required size, flanges, orifice plate, gasket etc of 100 mm sizes as required :(cabling will be part of Fire Alarm System)
448	Excavation for foundation upto 1.5 m depth including sortingoutandstacking of useful materials anddisposing off the excavated stuff upto 50 Meter lead.(B)Dense or Hard soil
449	Filling available excavatedearth (excluding rock) intrenches.plinth, sides of foundations etc. in layers not exceeding 20 cm. in depthconsolidating each dispositedlayer by ramming and watering.
450	Providing pipe protection for underground pipes from corrosion painting pipe with approved primer and covered with anticorrosive tape (4mm thick) of approved make as per specifications pipe size as follow: 80 mm diameter
451	Providing pipe protection for underground pipes from corrosion painting pipe with approved primer and covered with anticorrosive tape (4mm thick) of approved make as per specifications pipe size as follow: 100 mm diameter
452	Providing pipe protection for underground pipes from corrosion painting pipe with approved primer and covered with anticorrosive tape (4mm thick) of approved make as per specifications pipe size as follow: 150 mm diameter
453	Supplying,installation,testingandcommissioningof Electric driven Main Fire Pump suitablefor automatic operationandconsistingoffollowing,completeinall respects, as required :Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520. Suitable HP Squirrel cage induction motor, TEFC, synchronousspeed1500RPM,suitableforoperation on415volts,3phase50Hz,ACsupplywithIP55 protectionforenclosure,horizontalfootmountedtype with Class-\"F\" insulation, conforming to IS-325. M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitablecementconcretefoundationdulyplastered with anti vibration pads. 1620 lpm at 70 m Head
454	Supplying,installation,testingandcommissioningof diesel engine driven main fire pump suitable for automatic operation and consistingof following, completeinallrespects,asrequired:(DieselDriven Pump) Horizontal type, multistage, centrifugal pump of cast of iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520. SuitableHP,1500RPMwatercooledwithradiator, diesel engine conforming to relevant IS standard completewithautostartingmechanism,12/24volts electricstartingequipment,dieseltank,exhaustpipe extended upto 10 m outside pump house duly insulated with 50 mm thick glass wool with 1.0 mm thick aluminium sheet cladding, residential silencer, instruments and protection as per standard specification, stop solenoid for auto stop in the event of fault with audio indications, painted with post office red colour etc. as required. M.S fabricated, common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitablecementconcretefoundationdulyplastered and with anti vibration pads. 1620 lpm at 70 m Head
455	Supplying,installation,testingandcommissioningof electricdrivenpressurisationpumpsuitablefor automaticoperationandconsistingoffollowing, complete in all respects, as required : (Jockey Pump) Horizontaltype,multistage,centrifugalpumpofcast iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS : 1520. SuitableHPsquirellcageinductionmotorTEFCtype suitableforoperationon415volts,3phase50Hz AC supply with IP 55 class of protection for enclosure, horizontalfootmountedtypewithClass-\"F\"insulation,conforming to IS : 325. M.S.fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitablecementconcretefoundationdulyplastered and with anti vibration pads. 180 lpm at 70 m Head
456	Supplying,installation,testingandcommissioningof electric driven terrace pump suitable forautomatic operationandconsistingoffollowing,completeinall respects, as required: (Terrace Pump) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical confirming to IS : 1520. SuitableHPsquirellcageinductionmotorTEFCtype suitable for operation on 415 volts, 3 phase, 50 Hz, AC supplywithIP55classofprotectionforenclosure, horiziontalfootmountedtypewithClass-\"F\"insulation, conforming to IS-325. M.S.fabricated common base plate, coupling, coupling guard, foundation bolts etc.as required. Suitablecementconcretefoundationdulyplastered and with anti vibration pads. 450 lpm at 35 m Head
457	Fabrication, supply, Insallation testing & commissioning of Electrical control panel of cubical construction, floor mounted type, fabricated out of 2mm thick CRCA sheet, compartmentalised with hinged lockable doors, dust and vermin proof, powder coated of approved shade after 7 tank treatment process, cable alley, interconnection with suitable size copper conductor cable/solid copper strip, having switchgears and accessories, mountings and internal wiring, earth terminals, numbering etc. complete in all respect, suitable for main fire pump, pressurisation pump & diesel pump set complete as per CPWD specification with following in coming and Outgoings, suitable for operation on 415V, 3 phase, 50Hz Ac Supply with enclosure protection class IP 42 as required : INCOMING 250A, 50kA 4 Pole MCCB, Ics=100% Icu rating Digital Voltmeter 0-500V with selector switch Digital Ammeter (0-250 A) with selector swtich & CTs etc. LED type RYB phase indicating lamps, ON, OFF, trip indicating lamps Set of Copper Bus Bar 300A OUTGOING ( Note : All outgoing feeders for pumps should have digital Ammeter with selector switches, and LED type ON, OFF, trip indicating lamps)Main Fire Pump125 A, 50kA TPN MCCB, Ics=100% Icu, with fully automatic Star/Delta starter suitable for 60 HP pump with overload protection, current sensing type single phase preventor complete with all acceessories and internal wiring required for automatic operation selector switch for local/remote, auto/manual/OFF operation.Jockey Pump63 A, 50kA TPN MCCB, Ics=100% Icu, with suitable HP fully automatic Star/Delta starter with overload protection, current sensing type single phase preventor complete with all acceessories and internal wiring required for automatic operation, selector switch for local/remote, auto/manual/OFF operation.DIESEL ENGINE CONTROLControl for diesel engine comprising - Automatic/Manual selctor switch & 3 attempts starting device, timers and relays as required, push buttons, start/stop in manual mode Indicating lamp for high/ Low Lub. Oil pressure, High Water Temp and Engine on indication Battery charger suitbale for 12V/24 V DC with boost and trickle selector switch, 0-30 V DC volt meter, and 0- 20 A DC Ammeter All standard relays and accessories for automatic operation of diesel engine System ControllerDesigning, Supply, Installation, Testing and commissioning of system controller to control operation of main electric fire pump, diesel pump, Pressurization pump, Terrace pump in sequence as per specification consisting of relays, timers. Sensors, annunciation window for fault indication, complete as per specification
458	Modular Furniture : Providing ,Supplying and fixing of Factory made Moduler furniture as per below specification including erection at site.Bed (Size:1800Lmmx900Wmmx420Hmm)Bed Frame 1.2mm High Zink Coated GI sheet120 GSM and Bed Leg 60mmx30mmx2mm thickness CRCA Pipe with completely finished with powder coating.all raw materials and quality test certificate & capsure 18mmMR Grade plywood: with laminate & mattreses support 12mm MR Grade plywood with linner pested all complete as specified and as directed by the Engineer in- Charge and Architects
459	Providing ,Supplying and fixing of Factory made Moduler furniture as per below specification including erection at site. Bed Side TableSize:750mmx500mmx420mmCentre Table Drawers and other parts made of High zinc coated Galvanized Steel 1.0 mm thicknessprime export quality material withwith test certificate from galvanized steel manufacturer as per IS 277 standard. completely finished with powder coating.The telescopic drawer slides and concealed handle which should be very sturdy &able to take load upto 30kg to 40Kg all hardware will be of olive, godrej, hettich. all complete as specified and as directed by the Engineer in- Charge and Architects
460	Providing ,Supplying and fixing of Factory made Moduler furniture as per below specification including erection at site.Wordrobe Size:- 2200mm H(100mm+_)x600mm(10mm+_)Dx1000mmL Completely made of High zinc coated Galvanized Steel 1.0 mm thicknessprime export quality material withwith test certificate from galvanized steel manufacturer as per IS 277 standard. The Door & drawer should be of Double construction Foam sheet filled ingaps must required.The sound deadning Bufferto be used to minimize banging noise while closing the Door and Drawers.The Doors are mounted to the Soft Closing hinges which are openable to 90 degree & self closing on return.The telescopic drawer slides which should be very sturdy &able to take load upto 30kg to 40Kg. wardrobe to have door lock and key arragement all hardware will be of olive, godrej, hettich.wordrobe completely finished with powder coating with all raw materials and quality test certificate. all complete as specified and as directed by the Engineer in- Charge and Architects
461	Providing ,Supplying and fixing of Factory made Moduler furniture as per below specification including erection at site.Study TableSize:1200mm(10mm+_)Lx600mmDx775mmHt Study Table Drawers and other parts made of High zinc coated Galvanized Steel 1.0 mm thicknessprime export quality material withwith test certificate from galvanized steel manufacturer as per IS 277 standard.Legs 60mmx30mmx2mm thickness CRCA Pipe with completely finished with powder coating.The telescopic drawer slides which should be very sturdy &able to take load upto 30kg to 40Kg and grip handle at bottom drawer all hardware will be of olive, godrej, hettich. all complete as specified and as directed by the Engineer in- Charge and Architects
462	Providing ,Supplying and fixing of Factory made Moduler furniture as per below specification including erection at site. Study Chairs Study chair made of rubber wood frame with arm rest with melamine polish and seating and back part is of Cusion pu foam and fabric as per selection with complete fitting and study, chair has no caster. all complete as specified and as directed by the Engineer in- Charge and Architects
463	Providing ,Supplying and fixing of Factory made Moduler furniture as per below specification including erection at site.Bed Side TableSize:1050mmx500mmx420mmCentre Table Drawers and other parts made of High zinc coated Galvanized Steel 1.0 mm thicknessprime export quality material withwith test certificate from galvanized steel manufacturer as per IS 277 standard. completely finished with powder coating.The telescopic drawer slides and concealed handle which should be very sturdy &able to take load upto 30kg to 40Kg all hardware will be of olive, godrej, hettich. all complete as specified and as directed by the Engineer in- Charge and Architects
464	Providing ,Supplying and fixing of Factory made Moduler furniture as per below specification including erection at site. Chair with Castor,Flip Cushion Seat,Plastic Back,Fixed Arms,Collapsible Writing Desk - Small,Powdercoted 4 Legs with Castors,Book Mesh ( Same As per Image )
465	Providing ,Supplying and fixing of Factory made Moduler furniture as per below specification including erection at site.Reading Room Table (Size: 1000mm x 600mm)MS powder coated structure frame from 40mm MS pipes with 19mm particle board finished laminate of approved colours on both sides with safe rounded edges finshed with machine pressed PVC beading on all edges.The MS structure shall be powder coated after required 7 tank process. As approved by Architect.(Including transportation, loading, unloading and erecting/installation/placing of item at site as directed by Engineer in charge.)
466	Providing ,Supplying and fixing of Factory made Moduler furniture as per below specification including erection at site.Reading Room Chair frame in MS for strength and reliable performance and should have PU foam in back & Moulded PU Seat and Chrome Arms . It should be steady and have sled base with two sled legs wide enough to support the whole chair. As approved by Architect. (Including transportation, loading, unloading and erecting/installation/placing of item at site as directed by Engineer in charge.)
467	Providing ,Supplying and fixing of Factory made Moduler furniture as per below specification including erection at site. Single SeaterSofaWood Structure Made of rubber wood withmelamine polish seat and back made of MR Grade plywood with foam and fabric.all complete as specified and as directed by the Engineer in- Charge and Architects
468	Providing ,Supplying and fixing of Factory made Moduler furniture as per below specification including erection at site.Living Room Double Seater Sofa ht 830mm,width and length 1600mmx790,seat ht 410mm,arm thichness 180mm,seat widthand length 1140x510mm,foam size seat 125mm,28 density,foam back100mm and 28 density full cusion.all complete as specified and as directed by the Engineer in- Charge and Architects
469	Providing ,Supplying and fixing of Factory made Moduler furniture as per below specification including erection at site.Living Room Side Table Verve Glass Centre Table 610-FL, 1200 (W) X 600 (D) X 425 (H)
470	Providing ,Supplying and fixing of Factory made Moduler furniture as per below specification including erection at site.Living Room Corner Table Verve Glass Side Table 610-FS,600 (W) X 600 (D) X 505 (H)
471	Providing ,Supplying and fixing of Factory made Moduler furniture as per below specification including erection at site.Living Room 4 Seater Dining TableSize:1200mmX750mmx750mmTop 35mmthkMr grade Plywood with Laminate ,diningleg support thickness 100mmx100mmand melamine polish.all complete as specified and as directed by the Engineer in- Charge and Architects
472	Providing ,Supplying and fixing of Factory made Moduler furniture as per below specification including erection at site.Living Room Dining Chairs Made of rubber wood withmelamine polish seat and back cusion with pu foamand fabric.all complete as specified and as directed by the Engineer in- Charge and Architects
473	Providing ,Supplying and fixing of Factory made Moduler furniture as per below specification including erection at site.Bed Room (Bed Size: 1800mmx1800mmx385mm ht)All part should be 18mm,12mm and 8mm MR Grade Plywood with Laminate and linner (without Box)all complete as specified and as directed by the Engineer in- Charge and Architects
474	Providing ,Supplying and fixing of Factory made Moduler furniture as per below specification including erection at site.Bed Room side TableSize:600mmx450mmx420mmAll part should be 18mm,12mm and 8mm MR Grade Plywood with Laminate and linner with Drawer.the telescopic drawer slides which should be very sturdy &able to take load upto 30kg to 40Kg, with concealed handle, all hardware will be of olive, godrej, hettich. all complete as specified and as directed by the Engineer in- Charge and Architects
475	Providing ,Supplying and fixing of Factory made Moduler furniture as per below specification including erection at site.Bed Room Wardrobe Size:1800mmx600mmx2100mmWordrobeCompletely inner partmade of High zinc coated Galvanized Steel 1.0 mm thicknessprime export quality material withwith test certificate from galvanized steel manufacturer as per IS 277 standard. The Door 18mm board with Laminate The Doors are mounted to the Soft Closing hinges which are openable to 90 degree & self closing on return,The telescopic drawer slides which should be very sturdy &able to take load upto 30kg to 40Kg. wardrobe to have door lock and key arragement all handle is to be concealed handle,all hardware will be of olive, godrej, hettich with hanging rod ,unit inner partcompletely finished with powder coating with all raw materials and quality test certificate. all complete as specified and as directed by the Engineer in- Charge and Architects
476	Providing ,Supplying and fixing of Factory made Sofa as per below specification including erection at site. Three Seater Sofa ht 830mm,width and length 2020mmx790,seat ht 410mm,arm thichness 180mm,seat widthand length 1710x510mm,foam size seat 125mm,28 density,foam back100mm and 28 density full cusion.all complete as specified and as directed by the Engineer in- Charge and Architects
477	Providing ,Supplying and fixing of Factory made Moduler furniture as per below specification including erection at site.TV Unit (Living Area)Size:2630mmx427mmx493mmAll part should be 18mm,12mm and 8mm MR Grade Plywood with Laminate and linner with Drawer. the telescopic drawer slides which should be very sturdy &able to take load upto 30kg to 40Kg all hardware will be of olive, godrej, hettich. all complete as specified and as directed by the Engineer in- Charge and Architects
478	Providing ,Supplying and fixing of Factory made Moduler furniture as per below specification including erection at site.4 Seater Dining TableSize:1350mmX750mmx750mm. Top 35mmthkMr grade Plywood with Laminate ,diningleg support thickness 100mmx100mmand melamine polish.all complete as specified and as directed by the Engineer in- Charge and Architects
479	Providing ,Supplying and fixing of Factory made Moduler furniture as per below specification including erection at site.Study Table Size:1200mmx600mmx750mmHttop made of 18 mm MR grade ply with as per selection laminate finish.Study Table Drawers and other parts made of High zinc coated Galvanized Steel 1.0 mm thicknessprime export quality material withwith test certificate from galvanized steel manufacturer as per IS 277 standard.Legs 60mmx30mmx2mm thickness CRCA Pipe with completely finished with powder coating.The telescopic drawer slides which should be very sturdy &able to take load upto 30kg to 40Kg all hardware will be of olive, godrej, hettich. all complete as specified and as directed by the Engineer in- Charge and Architects
480	Providing ,Supplying and fixing of Factory made Moduler furniture as per below specification including erection at site.6 Seater Dining TableSize:1650mmX750mmx750mm. Top 35mmthkMr grade Plywood with Laminate ,diningleg support thickness 100mmx100mmand melamine polish.all complete as specified and as directed by the Engineer in- Charge and Architects
481	Providing ,Supplying and fixing of Factory made Moduler furniture as per below specification including erection at site. ALL STAFF AREA, FACULTY AREA, OFFICE AREALinear Sharing / Non Sharing Workstations System : SWITCH 40Size : 1200X600X1100HTSpecificationsTable Top: 25mm thick Pre laminate particle board with 2mm PVC edge lipping on all exposed edges ( Streight / Waterfall )Support: End Leg : SWITCH 40 Legs Intermediate Legs: MS podwer coated 60X40mm legs and supporting MS cross beams (40X20mm) Wire Management250mm Ht Racway with 65mm Dia Wire Manager GrommetSpecificationsVertical Raceway with built in separator for power and data of size 250H X 70mm thick with provision to mount swicthes and sockets on laminate facia with VerticalWire Entry cover for wire uptake from floor to raceway with 65mm Dia Wire ManagerGrommet.Main Screen : 18mm thick Fabric Magnatic Screen With AL trims mounted on stud 1050L X 350 HtIntermediate & End Screen : 8mm Color Glass mouinted on stud 675X350Ht
482	Providing ,Supplying and fixing of Factory made Moduler furniture as per below specification including erection at site. ALL STAFF AREA, FACULTY AREA, OFFICE AREAPRODUCT: PADESTAL (2D+1F) 2 Drawer + 1 FillingSIZE: 400 X 450 X 600HTSpecifications:Table Top: 18mm Thk pre laminated particle boardBack: 9mm Thk pre laminated particle board with 2mm PVC edge lippingShutters: 18mm Thk pre laminated particle boardEdge: All exposed area with 2mm thick PVC edge lippingHandle: Finger groove handleLock: Regular lock
483	Providing ,Supplying and fixing of Factory made Moduler furniture as per below specification including erection at site.Linear Sharing / Non Sharing Workstations System : SWITCH 40Size : 1050X600X1100HTSpecificationsTable Top: 25mm thick Pre laminate particle board with 2mm PVC edge lipping on all exposed edges ( Streight / Waterfall )Support: End Leg : SWITCH 40 Legs Intermediate Legs: MS podwer coated 60X40mm legs and supporting MS cross beams (40X20mm) Wire Management250mm Ht Racway with 65mm Dia Wire Manager GrommetSpecificationsVertical Raceway with built in separator for power and data of size 250H X 70mm thick with provision to mount swicthes and sockets on laminate facia with VerticalWire Entry cover for wire uptake from floor to raceway with 65mm Dia Wire ManagerGrommet.Main Screen : 18mm thick Fabric Magnatic Screen With AL trims mounted on stud 900L X 350 HtIntermediate & End Screen : 8mm Color Glass mouinted on stud 675X350Ht
484	Providing ,Supplying and fixing of Factory made Moduler furniture as per below specification including erection at site. MEDIUM HEIGHT STORAGE, SIZE: 1200x600x1200HT, Specifications: , Table Top: 18mm Thk pre laminated particle boardBack: 9mm Thk pre laminated particle board with 2mm PVC edge lippingShutters: 18mm Thk pre laminated particle boardEdge: All exposed area with 2mm thick PVC edge lippingHandle: Finger groove handleLock: Regular loc
485	Providing ,Supplying and fixing of Factory made Moduler furniture as per below specification including erection at site.PRINCIPAL AND VICE PRINCIPAL Cabin Table with Return storageSystem : ZEN TABLESize : Main Table : 1800X900X750With Fix Side Storage : 1200x450Specifications:Table Top: 25mm thick pre laminated particle board with matching PVC edgelippingSupport: 25mm thick pre particle board with matching PVC edge lippingModesty Panel: 1200 x 450HT- 18mm thick pre particle board modesty panel of450mm Ht.Side Screen: 25mm thick pre lam particle board with matching PVC edge LippingSide Storage: 25mm thick pre lmainated particle board with sliding shutters.Wire Management: 300 aluminium flip up with soft closure and provision to mountswitches and sockets on PVC cable dump
486	Providing ,Supplying and fixing of Factory made Moduler furniture as per below specification including erection at site.PRINCIPAL AND VICE PRINCIPAL Back Storage with Back Panel Back Storage : Size: (Z - S3) 750 X 450 X 700Back Pannel : ( ZBP B - 18090) 1800 X 25 X 900Specifications:Table & Back: 25mm thick pre laminated particle board with matching PVC edge lipping.Sides & Shutter: 18mm thick pre laminated particle board.Handle: Finger groove handleHardware: Door closing hinges, mini-fix, levellers & locks, etc.Note : ( Back Storage : Size: (Z - S3) 750 X 450 X 700 : 02 Nos )Back Pannel : Back Pannel : ( ZBP B - 18090) 1800 X 25 X 900 : 01 Nos )
487	Providing ,Supplying and fixing of Factory made Moduler furniture as per below specification including erection at site.HOD CABIN TABLE Size : 1800L x 750D x 750HtTable Top: 25mm thick Pre laminate particle board with 2mm PVC edge lipping on all exposed edges.Support: End Legs: Enrich legs and Supporting beams.Modesty Panel: 18mm thk pre lam board with 2mm PVC edge lipping of 450mm Ht. Wire Management: Slide connect with wireless charger and VertebraProviding, Supplying & Fixing Side storage Size : 1200L x 450D x 750HtSide Storage Made up of 18mm thick Prelam particle board with Number lock
488	Providing ,Supplying and fixing of Factory made Moduler furniture as per below specification including erection at site. Providing, Supplying & FixingSide storage, Size : 1200L x 450D x 750HtSide Storage Made up of 18mm thick Prelam particle board with Regular lock with connect legs at bottom of storage, Make:- Featherlite/ HOF / Approved by Architect
489	Providing ,Supplying and fixing of Factory made Moduler furniture as per below specification including erection at site.PRINCIPAL/ VICE PRINCIPAL / HOD CABIN CHAIRCabin Main Chairs, Amaze High Back Mesh Chair, AN 70 Mesh, Self Calibrating Multilock Mechanism, Adjustable Lumbar Support, One Way Adjustable Arms (Height), Nylon Base, Fabric Upholstered Cushion Seat
490	Providing ,Supplying and fixing of Factory made Moduler furniture as per below specification including erection at site. GROUND FLOOR- PRINCIPAL/ VICE PRINCIPAL / HOD CABIN Cabin Visitor Chairs Model : AMAZE MB, Amaze Medium Back Mesh Chair, AN 70 Mesh, Self Calibrating Multilock Mechanism, Adjustable Lumbar Support, One Way Adjustable Arms (Height), Nylon Base, Fabric Upholstered Cushion Seat
491	Providing ,Supplying and fixing of Factory made Moduler furniture as per below specification including erection at site.WORKSTATION CHAIRSMODEL : ALL WORKS MB, Allworks Medium Back Mesh Chair, AN -70 Mesh, Single Lock Synchro Mechanism, Adjustable Lumbar Support, One Way Adjustable Armrests ( Height), Nylon Base, Fabric Upholstered Cushion Seat & Back
492	Providing ,Supplying and fixing of Factory made Moduler furniture as per below specification including erection at site.PRINCIPAL/ VICE PRINCIPAL / HOD CABIN SOFAIModel No. 900 (converse - 3 seater sofa) made off solid wood frame, supported with high class webbing belt, 40/32/40 density foam used, topped with 2\" softy foam for great sitting experiace, upholstered with Tan Color Leatherrete size : 3 s : 1900 x 750 x 800SHADE: TANLeatherette
493	Providing ,Supplying and fixing of Factory made Moduler furniture as per below specification including erection at site.PRINCIPAL/ VICE PRINCIPAL / HOD CABIN SOFAModel No. 900 (converse - 1 seater sofa) made off solid wood frame, supported with high class webbing belt, 40/32/40 density foam used, topped with 2\" softy foam for great sitting experiace, upholstered with Tan Color Leatherrete size : 1 s :875 (W) x 750 (D) X 820 (H) SHADE: TANLeatherette
494	Providing ,Supplying and fixing of Factory made Moduler furniture as per below specification including erection at site.PRINCIPAL/ VICE PRINCIPAL / HOD CABIN 900 (converse - 2seater sofa) made off solid wood frame, supported with high class webbing belt, 40/32/40 density foam used, topped with 2\" softy foam for great sitting experiace, upholstered with Tan Color Leatherrete size : 2 s : 1375 x 750 x 800 SHADE: TANLeatherette
495	Providing ,Supplying and fixing of Factory made Moduler furniture as per below specification including erection at site.MULTI PURPOSE HALL LECTURETABLE Size: 800Lx 500D x 750Ht mm Specification :Table top : 25mm thick Pre-laminate particle board E1 norms finished with 2mm pvc edge banding.Under-structure : Supported on MS powdercoated Perform stright 50X50 Switch leg with supporting fixed beams.Modesty panel : 18mm thick Pre laminated modesty panel of 225mm gap from Floor levelWire management: 65dia Grommet provided, 70mm thick and 250mm HtMetal Racewaywith laminate Facia for provision to mount swicthes and sockets on laminate facia. vertical cover for cable access from floor to Raceway
496	Providing ,Supplying and fixing of Factory made Moduler furniture as per below specification including erection at site.MULTI PURPOSE HALL CHAIRSALPHA VA PC 4 LEGS -PP Grey, Alpha Medium PP (Black)Back Mesh Chair, AN 70 Mesh, Fabric Upholstered Cushion Seat, FixedArms, Powdercoated 4 LegsMake:- Featherlite/ HOF / Approved by Architect
497	Providing ,Supplying and fixing of Factory made Moduler furniture as per below specification including erection at site.TABLE WITH PADESTAL (2D+1F )SYSTEM : PERFORMSIZE : MAIN TABLE : 1200x600x750SpecificationsTable Top: 25mm thick Pre laminate particle board with 2mm PVC edge lipping on all exposed edgesSupport:End Legs: MS powder coated PERFORM legs (50X50)Modesty Panel: 18mm thk pre lam board with 2mm PVC edge lipping of 450mm HtWire Management: 65mm Dia Wire Manager GrommetPADESTAL (2D+1F) 2 Drawer + 1 FillingSIZE: 400 X 450 X 600HTSpecifications:Table Top: 18mm Thk pre laminated particle boardBack: 9mm Thk pre laminated particle board with 2mm PVC edge lippingShutters: 18mm Thk pre laminated particle boardEdge: All exposed area with 2mm thick PVC edge lippingHandle: Finger groove handleLock: Regular lock
498	Providing ,Supplying and fixing of Factory made Moduler furniture as per below specification including erection at site.Podium: Lecturer Table 25mm thk pre-laminated board (PLB) with storage, with castors for easy movement. As approved by Architect. (Including transportation, loading, unloading and erecting/installation/placing of item at site as directed by Engineer in charge.) Size: 900mm x 950mm x 750mm
499	Providing ,Supplying and fixing of Factory made Moduler furniture as per below specification including erection at site. Reception Table : Worksurface and Modesty Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shadeconfirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Access Flap provided on work surface for wire management. Power box made with 0.8 mm thick CRCA (IS: 513), with switch plate (8+3 Modulecutout provision for Anchor Roma). This is fixed with worktop along the width atAccess Flap position. Understructure/Top shelf/Hinge door Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shadeconfirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Drawer unit - **Drawer bottom is made of 5.5thk MDF whiteboardHandle is provided for ease of opening.HDU and Drawer is provided with cam lock for security
500	Providing ,Supplying and fixing of Factory made Moduler furniture as per below specification including erection at site. 900 (converse - 3 seater sofa) RECEPTION AREA made off solid wood frame, supported with high class webbing belt, 40/32/40 density foam used, topped with 2\" softy foam for great sitting experiace, upholstered with Tan Color Leatherrete size : 3 s : 1900 x 750 x 800SHADE: TANLeatherette

Tender Documents

SR No	FileName	File Description
1	Click here to download tender document	Tender Documents
2	Click here to download tender document	Tender Documents
3	Click here to download tender document	Tender Documents
4	Click here to download tender document	Tender Documents
5	Click here to download tender document	Tender Documents
6	Click here to download tender document	Tender Documents
7	Click here to download tender document	Tender Documents
8	Click here to download tender document	Tender Documents
9	Click here to download tender document	Tender Documents
10	Click here to download tender document	Tender Documents
11	Click here to download tender document	Tender Documents
12	Click here to download tender document	Tender Documents
13	Click here to download tender document	Tender Documents
14	Click here to download tender document	Tender Documents
15	Click here to download tender document	Tender Documents
16	Click here to download tender document	Tender Documents
17	Click here to download tender document	Tender Documents
18	Click here to download tender document	Tender Documents
19	Click here to download tender document	Tender Documents
20	Click here to download tender document	Tender Documents
21	Click here to download tender document	Tender Documents
22	Click here to download tender document	Tender Documents
23	Click here to download tender document	Tender Documents
24	Click here to download tender document	Tender Documents

Also Visit

Tenders

Lakshadweep Tenders

Construction Tenders

Building Construction Tenders

Building Work Tenders

Disclaimer

We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.

Top

Tender For Development Of Nursing And Paramedical College At Kavaratti, Lakshadweep, Kavaratti-Lakshadweep

Tender Documents

Disclaimer

About Us

Services

Browse Tenders

For Sales Inquiry

Tender For Development Of Nursing And Paramedical College At Kavaratti, Lakshadweep, Kavaratti-Lakshadweep

Tender Documents

Disclaimer

OTP Verification

About Us

Services

Browse Tenders

For Sales Inquiry

Connect With Us