|
| 1 | Surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m. All kinds of soil. |
| 2 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil. |
| 3 | Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. |
| 4 | Supply of Earth Including royality,excavation,Loading & unloading and carriag by mechnical transport lad upto 5 K.M banking excavatd earth in laying not exceeding 20 cm in depth,breaking clods,watering,rolling each layer with 1/2 tonne rollr or wooden or stel rammers,and rolling every 3rd and top-most layer with power roller of minimum 8 tonnes and dressing up in mbankments for roads flood banks,marginal banks and guide banks or filling up ground depressions and lift upto 1.5 m in all kind of soil. |
| 5 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size). |
| 6 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:1½:3 (1 Cement: 1½ coarse sand: 3 graded stone aggregate 20 mm nominal size). |
| 7 | Masonry work with C&D recycled cement concrete bricks of size 230 mm x 110 mm x 75 mm of grade M-10 in super structure above plinth level upto level-II with cement mortar 1:6 (1 cement : 6 coarse sand) |
| 8 | Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in- charge (length of finished kerb edging shall be measured to calculate volume for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge). |
| 9 | Basic rate for Providing and laying EPDM rubber flooring 20 mm thick(Loading,unloading,installation, GST and overhead charge extra). |
| 10 | Providing and laying Designer Paver Milano Design (60mm thick, M-30) Bedding Layer - 60 mm thick of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge. |
| 11 | Providing and laying 60 mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge. |
| 12 | Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. |
| 13 | Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.Polished Granite stone slab of colour Black, Cherry/Ruby Red or equivalent. |
| 14 | Granite work (mirror polished and machine cut) (all colour except black,cherry/ruby red) of thickness 18mm for wall lining (veneer work) including dado skirting riser of steps etc. in required design and pattern where ever required as per direction of Engineer in Charge, backing filled with a groutof average 12mm thick in cement mortar 1:3 (1 cement : 3 coarse sand ) including pointing with white cement mortar 1:2 (1 cement : 2 marble dust ) with as admixture of pigment to match the granite shade ( to be secured to the backing by means of cramps, which shall be paid separately) Granite stone (all colour except black,cherry/ruby red). Area of slab over 0.50 Sqm. |
| 15 | Providing and fixing carbon steel galvanised ( minimum coating 5 micron) dash fastener of 10 mm dia double threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head, comprising of 10 mm dia polyamide PA 6 grade sleeve, including drilling of hole in frame , concrete/ masonry, etc. as per direction of Engineer-in-charge. 10 x 120 mm |
| 16 | Dismantling stone slab flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 metres lead. |
| 17 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-Charge) of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05mm) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 18 | Washed stone grit plaster on exterior walls height upto 10 metre above ground level, in two layers, under layer 12 mm cement plaster 1:4 (1 cement : 4 coarse sand ), furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 2 Kg of cement per square metre, top layer 15 mm cement plaster 1:1/ 2:2 (1 cement: 1/2 coarse sand : 2 stone chipping 10 mm nominal size), in panels with groove all around as per approved pattern, including scrubbing and washing the top layer with brushes and water to expose the stone chippings ,complete as per specification and direction of Engineer-in-charge (payment for providing grooves shall be made separately). |
| 19 | Forming groove of uniform size in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer, including removal of wooden battens, repair to the edges of panels and finishing the groove complete as per specifications and direction of the Engineer-in-charge : 15 mm wide and 15 mm deep groove |
| 20 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets,gates and similar works |
| 21 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work |
| 22 | Providing and fixing precast reinforced cement concrete bench of over all size 1500 mm x 450 mm x 1000 mm, the bench consist of 02 nos. L-shape base sport in cement, thickness 100 mm back height 1000 mm front height 450 mm base width 620 mm as per sketch and 05 nos. reinforced concrete planks in red colour of sized 1500 mm x 100 mm x 50 mm and 01 nos. RCC planks of size 1500 mm x 200 mm x 50 mm by using M-30 grade of concrete using vibro compaction process, bench top and back planks are treated with special anti-corrosive water proof coating so as to make surface glossy and water proof including transportation, erection all part are jointed to gather with galvanized nuts and bolts of suitable size. All bolts are sealed after assembly. |
| 23 | Supply & fixing of Arihant /Kompon /Landscape /Koochie / Hugo / Grandslam Fitness Make ABS BOARD/ SIT UP BOARD (Double) of size 1400x1366x650mm fabricated with main post of 114mm and “C” Class G.I. pipe made of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nobel of 60-80 micron thick. All joints of pipe are4 robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint are applied at all welding points prior to finishing. Sit up boards and Base plate cover to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic of 8mm, colourful and UV resistant and environmental friendly. All complete as per direction and approval of engineerin- charge regarding material, shape of equipment, colour on metal, seat and base pedal and fixing of equipment etc including earth work, c:c work up to plinth level, c:c block 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size) of required size as per department / manufacturers specifications and guidelines. Including anchor fasteners on a concrete foundation and J shaped welded bolt and once the concrete is set, fix the equipment on to it and cover nuts and bolts with technical specifications. |
| 24 | Supply & fixing of Arihant /Kompon /Landscape /Koochie / Hugo / Grandslam Fitness Make SHOULDER TWIRL DOUBLE / ARM WHEEL make of size 857x850x1815mm fabricated with main post of 114mm and “C” Class G.I. pipe made of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nobel of 60-80mm micron thick. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paints are applied at all welding points prior to finishing. Packaging: Safety 3-layer packaging like 1st EPE Foam 2nd HDPE Film and 3rd is Stretch wrap. All complete as per direction and approval of engineer-in-charge regarding material, shape of equipment, colour on metal, seat and base pedal and fixing of equipment etc including earth work, c:c work up to plinth level, c:c block 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size) of required size as per department / manufacturers specifications and guidelines. Including anchor fasteners on a concrete foundation and J shaped welded bolt and once the concrete is set, fix the equipment on to it and cover nuts and bolts with technical specifications. |
| 25 | Supply & fixing of Arihant /Kompon /Landscape /Koochie / Hugo / Grandslam Fitness Make Aerial Stroller • Product Area : 1m x 0.5m (5ft x 2.6ft) • Safe Play Area : 2m x 1.5m (6.6ft x 5ft). Ideal For 13 Years & above. • Strengthens Leg Muscles. Lower body workout Technical Specification: The Aerial Stroller having Ergonomic design with 80NB GI main vertical support pipes of Aerial Stroller are fixed over 10mm thick base plate. Clamping plates are attached to main frame to hold the rest of assemblies. Bottom horizontal pipe is of 50NB GI pipe. An ergonomically designed Handle frame is connected to main frame. Footrest bend and Handle having 40NB and 25NB Dia galvanized pipe respectively. The materials used for foorest is aluminum/LLDPE/HDPE/Nylon. Specially designed mounting flange assembly having circular flange of 130mm dia with 16mm thickness is provided for footrest assembly. All metal pipes are Hot Dipped Galvanized Pipes conforming to IS 1239 (Part 1) with GI thickness of 60micron. Pipe Materials & Class: Heavy Duty (\"C\" Class) Series of pipes only. Wall thickness of pipe varies according to class/series of pipe used. Powder coating shall be done with pure polyester raw material.Dry film Thickness maintained within the range of 50-70 microns.it is tested for adhesion test (According to ASTM-D-3359) with the help of cross hatch cutter instruments. Bearing Housing shall be made from MS material. Bearings are oil sealed, self-lubricated made of SKF/ NTN/ NACHI / FAG / NRB make shall be provided for smooth & trouble-free movement. Pins shall be made from EN8/ MS material & Circlips made from standard material. Nut and Bolts: Galvanized/ S.S./Allen Bolt/Button Head Allen Bolt & Nuts / Nylon Lock Nuts are used with PVC Bolt Caps All open ends of pipe been closed by GI / PVC caps for user safety against entrapment. Certificate: ISO9001:2015. Color shall be Multicolorfor optional or customized and as per RAL Shade. Safety 3 layer packaging like 1st EPE Foam 2nd HDPE Film and 3rd is Stretch wrap. including earth work, c:c work up to plinth level, c:c block 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size) of required size as per department / manufacturers specifications and guidelines. Including anchor fasteners on a concrete foundation and J shaped welded bolt and once the concrete is set, fix the equipment on to it and cover nuts and bolts with technical specifications. |
| 26 | Supply & fixing of Arihant /Kompon /Landscape /Koochie / Hugo / Grandslam FitnessMakeChest & Shoulder Exercise Combo: Item Descriptions • Product Area : 2020mm x 1050mm • Safe Play Area : 4020mm x 3050mm• Ideal For : 13 Years & above Function • Strengthens Back Muscles.• trengthens Chest Muscles.• Upper body workout Technical Specification:•Post Dia: The \"Chest & Combo \" having Ergonomic design with 100NB GI main vertical support pipe isfixed over 10mm thick base plate. clamping plates are attached to main frame to hold the rest of assemblies.•Footrest and Handles: Footrest frame and Handle having 32NB and 25NB Dia galvanized pipe with Rubber grips respectively. •Seat: Ergonomically Designed, Complete Rotational Molded single piece part, Material :- LLDPE/HDPE/Nylon. •Pipes: All metal pipes are Hot Dipped Galvanized Pipes conforming to IS 1239 (Part 1) with GI thickness of 60micron. •Pipe Materials or Class: Medium Duty (\"B\" Class) and Heavy Duty (\"C\" Class) Series of pipes only.Wall thickness of pipe varies according to class/series of pipe used.•Powder coating:it shall be done with pure polyester raw material.Dry film Thickness maintained within the range of 50-70 microns.it is tested for adhesion test (According to ASTM-D-3359) with the help of cross hatch cutter instruments.•Bearing Housing is made from MS material. •Bearing: Bearings are oil sealed, self-lubricated made of SKF/ NTN/ NACHI make, to provid smooth & trouble-free movement. •Pins and Circlips: 25mm and 47mm diameter pins are made from EN9 material & Circlips made fromstandard material. •Nut and Bolts: Galvanized/ S.S./Allen Bolt/Button Head Allen Bolt & Nuts / Nylon Lock Nuts are used with PVC Bolt Caps. All open ends of pipe been closed by GI / PVC caps for user safety against entrapment. Certificate: ISO9001:2015 Color: Multicolor for optional or customized and as per RAL Shade. Packaging: Safety 3 layer packaging like 1st EPE Foam 2nd HDPE Film and 3rd is Stretch wrap. including earth work, c:c work up to plinth level, c:c block 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size) of required size as per department / manufacturers specifications and guidelines. Including anchor fasteners on a concrete foundation and J shaped welded bolt and once the concrete is set, fix the equipment on to it and cover nuts and bolts with technical specifications. |
| 27 | Supply & fixing of Arihant /Kompon /Landscape /Koochie / Hugo / Grandslam Fitness LEG EXTENTION : Product Area: 0.73m x 0.75m (2.4ft x 2.5ft).Safe PlayArea: 2.73m x 2.75m (8.9ft x 9ft). Ideal For: 13 Years & above. Function:For lower body workout.Technical Specification:Main Frame of Leg extension is 100NB G.I Pipe.The paired 25NB pipe handle with PVC/ rubber handgrips at the end is fixed over 40NB pipe frame.Two rolling frames are made by 40 NB & 20 NB G.I. pipes. Rolling frames are hinged at the one end of 40 NB bend pipe frame with specially designed bearing housing. The materials used for forest are aluminium/LLDPE/HDPE/Nylon. A suitable Nylon roller is provided for foot rest on rolling frame forcushioning purpose. Two PU rubber bushes are attached to main support pipe to avoid jerk due toimpact of rolling frames.Bearing Housing shall be made from MS material. Bearings are oil sealed, selflubricated made of SKF/ NTN/ NACHI make shall be provided for smooth & trouble-free movement. All metal pipes are Hot Dipped Galvanized Pipes conforming to IS 1239 (Part 1) with GI thickness of 60micron. Medium Duty (\"B\" Class) and Heavy Duty (\"C\" Class) Series of pipes only. Wall thickness of pipe varies according to class/series of pipe used. Powder coating shall be done with pure polyester raw material. Dry film Thickness maintained within the range of 50-70 microns.it is tested for adhesion test (According to ASTM-D-3359) with the help of cross hatch cutter instruments.Nut and Bolts: Galvanized/ S.S./Allen Bolt/Button Head Allen Bolt &Nuts / Nylon Lock Nuts are used with PVC Bolt Caps. All open ends of pipe been closed by GI / PVC caps for user safety against entrapment. Certificate: ISO9001:2015. Color shall be Multicolor for optional or customized and as per RAL shade. Safety 3-layer packaging like 1st EPE Foam 2nd HDPE Film and 3rd is Stretch wrap. including earth work, c:c work up to plinth level, c:c block 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size) of required size as per department / manufacturers specifications and guidelines. Including anchor fasteners on a concrete foundation and J shaped welded bolt and once the concrete is set, fix the equipment on to it and cover nuts and bolts with technical specifications. |
| 28 | Supply & fixing of Arihant /Kompon /Landscape /Koochie / Hugo / Grandslam Fitness Make HIP TWISTER TRIPLE/ WAIST TWISTER size1840x1840x2000mm fabricated with main post of 114mm “C” Class G. I. Pipe made of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nobel of 60-80mm micron thick. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paints are applied at all welding points prior to finishing. Rotating and base plate cover to be made from virgin LLPDE manufactured by rotational moulding with minimum thickness of plastic of 8mm colourful and UV resistant and nvironmental friendly. Bearing used shall be made maintenance free, duly oil sealed and self-lubricated made by reputed company to be approved by Engineer-incharge. Equipment to be fitted with inbuilt limiter to prevent unwanted movement. Safety 3-layer packaging like 1st EPE Foam 2nd HDPE Film and 3rd is Stretch wrap. All complete as per direction and approval of engineer-in-charge regarding material, shape of equipment, colour on metal, seat and base pedal and fixing of equipment etc including earth work, c:c work up to plinth level, c:c block 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size) of required size as per department / manufacturers specifications and guidelines. Including anchor fasteners on a concrete foundation and J shaped welded bolt and once the concrete is set, fix the equipment on to it and cover nuts and bolts with technical specifications. |
| 29 | Manufacturing, supplying and fixing retro reflective overhead signage boards made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity and encapsulated lens type heat activated retro reflective sheeting conforming to type - III of ASTM-D-4956-01 as approved by Engineer-in-charge, letters, borders etc. as per IRC : 67-2001 in silver white with blue colour back ground and with high intensity grade, pasted on substrate by pressure sensitive adhesive backing which shall be activated by applying pressure conforming to class II of ASTM-D-4956-01 and fixing the same to the plate of structural frame work by means of suitable sized aluminium alloys, rivets or bolts & nuts @ 300 mm centre to centre all along the periphery as well as in two vertical rows along with theft resistant measures, including the cost of painting with two or more coats of epoxy paint in grey colour on the back side of aluminium sheet including appropriate priming coat. The rate includes the cost of rounding off the corners, lowering down the structural frame work from the gantry, fixing and erecting the same in position all complete as per drawings, specification and direction of the engineer-incharge.( Structural frame work including M.S. plate to be provided separately. Rectangular area of the sheet only shall be measured for payment). Overhead informatory road signage Please Enable Macros to View BoQ information |
