Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Taking downcement or cement lime plaster on brick or stone wallsetc including raking out joints, hacking for key, scrubbing down with water etc.complete all as specified and as directed by Engineer-in-charge. |
| 2 | Supplying and applying for two component elestomeric acrylic polimer modified cementitious water proofing coating on brick wall SmartCare Damp Block 2k or approved eqivalent having 1005 elengotation as per ASTMD412 , resisting 5 bars hydrostatic pressure as per DIN 1048 reduction to rapid chloried 70 as per ASTMC 1202 ,crack bridging up to 1.2 mmas per ASTM 4548.5 The Coating shall havefood grade Certificate from laboratories like CFTRI, will be applyon both Positive & Negative side and resist upto 5 Bars of Hydrostic pressure .The mixing ratio of coating shall be 2 parts of powder & 1 part of liquid without any water addition in the mixing etc .after coating will sprinkle sand on the coatingthen apply plaster on the coating which is in contractor scope of work complete all as specified and as directed by Engineer-in-charge.Note: The cost ofSteel props adjustable (Suspended/Supported) Scaffolding (6m -7 m) Hight , safety equipment for labours (Belt,hook,Helmet) shall deemed to be included in quoted rates . |
| 3 | Mateial and labour for providing mixing & applying two component Epoxy resin concrete bonding coat on prepared RCC surface as per manufacturer instruction including preparation of surface by chipping and throughly cleaning of surfaces complete all as specified and as directed by Engineer-in-charge |
| 4 | Materaial and labour for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar1:4mixedwith liquid water proofing compound as per manufacturers instructions finished even and smooth without using extra cement on external surfaces complete all as specified and as directed by Engineer-in-charge.Note:- Liquid WPC Shall be measured and paid Separately under appropiate item of this BOQ |
| 5 | Material and labour for 10 mm thick rendering on other than fair faces of brick work or concrete surface in cement mortar 1:6finishing the surface even and smooth without using extra cement complete all as specified and as directed by Engineer-in-charge |
| 6 | Material and labour for rendering 5mm thick brick or concrete surface as in ceiling in cement mortar 1:3finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-charge |
| 7 | Material and labour for preparation ofnew plastered or unplastered surfaces of walls and applying two coats of cement base paint over and including a coat of primercomplete all as specified and as directed by Engineer-in-charge |
| 8 | Material and labour for preparation of new plastered or unplastered surfaces of walls and applying two coats ofdistemperoil emulsion over and including a coat of primer complete all as specified and as directed by Engineer-in-charge |
| 9 | Material and labour for preparation of new plastered or unplastered surfaces of ceiling and applying three coat of white washcomplete all as specified and as directed by Engineer-in-charge |
| 10 | Material and labour for complete removal of existing treatment of any type/description such as distempering work ,internal emulsion etc from internal/external surfaces of walls & ceiling with mechanical means/grinder including removal of material from site complete all as specified and as directed by Engineer-in-charge |
| 11 | Material and labour for preparation ofold plastered or unplastered surfaces of walls and applyingtwo coats of cement base paint complete all as specified and as directed by Engineer-in-charge |
| 12 | Material and labour for preparation of old plastered or unplastered surfaces of walls and applying two coats ofdistemper oil emulsion complete all as specified and as directed by Engineer-in-charge |
| 13 | Material and labour for preparing old plastered surfaces of ceilings and applying twocoats of white wash complete all as specified and as directed by Engineer-in-charge |
| 14 | Demolition of brick work built in cement mortar includingall quoins, arches, pillar etc ( in Foul position ) complete all as specified and as directed by Engineer-in-charge. |
| 15 | Material and labour for brick work with Fly ash bricks straight or curved on plan exc 6 mtr mean radius built in cement mortar 1:6 ( as in manholes) complete complete all as specified and as directed by Engineer-in-charge |
| 16 | Material and labour for brick worki using old size Fly ash bricks staight or curved on plan to any raidus as in half thick brick walls built in cement mortar (1:4) complete complete all as specified and as directed by Engineer-in-charge |
| 17 | Taking down chowkhats or frames (without taking off shutters from the frame) exc 1.5 Sqm and n. exc 4.00 Sqm including cutting holes of required sizefor hold fast block for new frame and making good the disturbed surface to match the existing surface complete complete all as specified and as directed by Engineer-in-charge |
| 18 | All as per srl item 17hereinbefore but n. exc 1.5 sqm each.complete all as specified and as directed by Engineer-in-charge |
| 19 | Supply and fixing Pressed steel frames size 105x 60mm made out of1.25 mm thick MS sheet f for doors with single rebate including necessary fixing lugs, hinges, lock strike plate, complete all as specified and as directed by Engineer-in-charge Note :- Disturbed portion of existing floor /wall / tile / plaster etc duing fixing of chowkhatsshall be repaired to match with existing finish. |
| 20 | Supply and fixing Pressed steel frames size 125x 60mm made out of1.25 mm thick MS sheet f for doors with single rebate including necessary fixing lugs, hinges, lock strike plate, complete all as specified and as directed by Engineer-in-charge. Note :- Disturbed portion of existing floor /wall / tile / plaster etc duing fixing of chowkhatsshall be repaired to match with existing finish. |
| 21 | Material and labour forcement concrete (1:3:6) type C-0,using 12.5 mm graded mechanically crushed stone aggregate as in back filling of pressed steel frame /hold fast blocks etc and similar work complete all as specified and as directed by Engineer-in-charge |
| 22 | Supply and fixing 30 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed by Engineer-in-charge |
| 23 | Supply and fixing 35mmthick, 2nd class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and as directed by Engineer-in-charge |
| 24 | Supply and fxing aluminium, anodised, barrel tower bolt 200mm longof extruded section and fixed complete all as specified and as directed by Engineer-in-charge |
| 25 | Supply and fixingaluminium alloy anodised sliding door bolt 300mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts complete all as specified and as directed by Engineer-in-charge |
| 26 | Supply and fixingextruded aluminum alloy handles, fabricated type, anodised 150 mm size complete all as specified and as directed by Engineer-in-charge. |
| 27 | Supply and fixing mild steel butt hinges of size 100mm medium weight cold rolled complete all as specified and as directed by Engineer-in-charge. |
| 28 | Supply and fixing floor door stopper of aluminium alloy body and tongue anodised with hard drawn steel spring fixed in floor overall length of cover plate 140mm complete all as specified and as directed by Engineer-in-charge. |
| 29 | Supply and fixing 300 mm long MS rat tail pattern spring hinge (helical door spring) including roller and roller plate complete all as specified and as directed by Engineer-in-charge |
| 30 | Material and labour for providing and fixing factory made extruded aluminium casement windows with 50 micron powder coating doubled panelled anddouble shutters consisting of frame and mullion of 101.60X44.45X1.29 mm and shutters made of 63.5X31.75X1.29mm and to be fixed with and including EPDM gasket to render the glazing, air and water tight etc. & aluminium beeds 20mm size with and including 5mm thick glass in front shutters and stainless steel wire gauge 0.36mm dia and 1.40 aperature in inner shutters complete all as specified and as directed by Engineer-in-charge including supply and fixing following items :-(a) Stainless Steel (304 Grade) Finished Butt Hinges 150mm -2 nos per leaf.(b) Powder Coated Aluminium Tower Bolt 150mm long - 2 nos per leaf.(c) Powder Coated Aluminium Handles 150 mm - 1 nos per leaf.(d) Note:- For Cooler fixing arrangement 08 nos shutter Each window.(as per direction by Eng-in-Charge) |
| 31 | Supply and fixing Powder coated Aluminium anodised DG 102 \"DECO\" grill of size 100mm x 10mm x7mm thick, approved design for windows / ventilators with and including F/U channel,complete all as specified and as directed by Engineer-in-charge |
| 32 | Material and labour for Providing and fixing factory made extruded aluminium ventilators with 50 micron powder coating of frame of 63.5 X 38.10 X 1.29 mm including 5mm thick frosted glass in lower 55% portion of shutters and stainless steel wire gauge 0.36mm dia and 1.40 aperture in upper 45% portion of shutter and to be fixed with and including EPDM gasket to render the glazing, air and water tight etc. & aluminium beeds 20mm size complete in all respectall as specified and as directed by Engineer-in-charge |
| 33 | Supply and fixing Steel cup board shutter made out pressed steel frame of size 75mm x45mm x 1.25mm thickwith prressed steelshutter 01mm thick Godrej pattern fixed to masonry wall by hold fasts made out of 25x3mm flat iron including mild steel CPhanging rod of 20mm dia with brackets fixed on inner side of one leaf of shutter and on other leaf provision of mild steel CP peg set of 3 including spray painting with two coats of synthetic enemal paint over one coat of red oxide primer all around on steel surfaces of frame and shutter including taking down existing wooden cup board and making good disturbed portion in CM 1:3 or PCC 1:2:4 all as specified and directed. 1.25 mm thick in frame work, cut to size, holes punched, welding, riveting, turning, bending etc. as require to made it in Godrej pattern complete all as specified and as directed by Engineer-in-charge |
| 34 | Suppy and fixing galvanised mild steel wire cloth ,0.56 nominal dia of wire and width of aperture 1.18 mmfixed with wooden bedstinned tacks or wire staples complete all as specified and as directed by Engineer-in-charge |
| 35 | Material and labor for preparationof newwood and wood basedsurface of any description over 10cm width or girth not otherwise described and applying twocoat of synthetic enamel paint over and including a coat of pink primer complete all as specified and as directed by Engineer-in-charge |
| 36 | Demolition of cement concrete (un-reinforced) in ground floors and pavings n exc 15cm thickness (below or above ground level) complete all as specified and as directed by Engineer-in-charge |
| 37 | Dismantling of floorhearth or wall tiling including cement mortar bedding (but not backing) andrubbish off the premises complete all as specified and as directed by Engineer-in-charge |
| 38 | Material and labour for 40 mm thick cement concrete (1:2:4) type B-1 using 20 mm graded crushed stone aggregates asin floor/paving etc complete all as specified and as directed by Engineer-in-charge |
| 39 | Material and labour for Non skid ceramic white tiles 7-8 mm thick(square/rectangular) area of each tile exceeding 0.18 sqm but n.exc 0.38 Sqm as in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15mm thick screed beeding in cement mortar1:6 complete all as specified and as directed by Engineer-in-charge. |
| 40 | Material and labour forNon Skid ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including15 mm thick screed bed in cement mortar 1:6 complete all as specified and as directed by Engineer-in-charge |
| 41 | Materaial and labour forglazed ceramic white tiles of size450X 300X 7mm thick thickas on vertical surfaces,set and jointed in neat cement slurry and pointed in white or coloured cement to match laid/fixed over and including 10 mm thick rendering in cement mortar 1:4complete all as specified and as directed by Engineer-in-charge |
| 42 | Materaila and labour for chequered cement concrete tiles 20cmx20cmx25mm thick, with grey cement and pigment, set, jointed and pointed and in neat cement slurry as in floor laid over and including20 mm thick screed bed or bedding layer of cementmortar 1:6complete all as specified and as directed by Engineer-in-charge |
| 43 | Material and labour for 12 mm thick (7ply) Plywood grade BWR ,type BB , fixed with screw to timber frame-work complete all as specified and as directed by Engineer-in-charge |
| 44 | Supply and fixing 1.50 mm thick Decorative type lamination type -1 of surface finish,colour and patern as approved including fix with approved adhesive complete all as specified and as directed by Engineer-in-charge |
| 45 | Supply and fixing continuous (piano) hinges, width of flap (when open) 30 mm, mild steel, bright finish or electro galvanised complete all as specified and as directed by Engineer-in-charge |
| 46 | Supply and fixing Rim latch having size of rach 75 mm with two levers of mild steel body, stove enamelled finish with brass knob or lever handle and fixed complete all as specified and as directed by Engineer-in-charge |
| 47 | Supply and fixing extruded brass handles febricated type polished of size 75 mm and fixed complete all as specified and as directed by Engineer-in-charge |
| 48 | Material and labour for2nd class soft wood ,Clean Sawn ,timber framed as in Scantlings as in Wall/Ceiling etc complete all as specified and as directed by Engineer-in-charge |
| 49 | Material and labour for plain fillets, square, rectangular or traingular in sec of 2nd class softwood not exc 3 Sqcm ,clean swan ,Secured with nails or brads etc complete all as specified and as directed by Engineer-in-charge. |
| 50 | Supply and fixingin repair sinks with drainage board made of stainless steel sheet 1mm thick forkitchen or laboratory with plugs washers and wastes icluding bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe over all size 915mm x 460mm bowl size 410mm x 330mm x 160mm.complete all as specified and as directed by Engineer-in-charge |
| 51 | Taking up or down steel tubing of size15mm bore including connections andremoval to store or from site complete all as specified and as directed by Engineer-in-charge. |
| 52 | Taking up or down steel tubing of size15mm bore including connections andremoval to store or from site complete all as specified and as directed by Engineer-in-charge. |
| 53 | Supply and laying25 mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings fixed on walls/ceiling or laid in floors complete all as specified and as directed by Engineer-in-charge. |
| 54 | Supply and laying 32 mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings fixed on walls/ceiling or laid in floors complete all as specified and as directed by Engineer-in-charge. |
| 55 | Supplt and fixing in repair Stainles steel chromium plated 20mmcurtain rod with fixing brackets, stops rollersscomplete incl fixing brackets, stops etc complete all as specified and as directed by Engineer-in-charge. Note:-For the purpose of mesurement and payment running length of curtain rod only shall be considered. |
| 56 | Dismantling of brick tiles or terracing tiles single layar on roofs complete all as specified and as directed by Engineer-in-charge. |
| 57 | Demolation of mud puska in roof any thickness including plastering and leeping ( whether full thickneess removed or part thereof ) complete all as specified and as directed by Engineer-in-charge. |
| 58 | Roughening surfaces of old concrete floor by picking, sweeping cleaning and washing down with water to remove dust, etc complete all as specified and as directed by Engineer-in-charge. |
| 59 | Material and labour for cement concrete 1:3:6, type C-0 using 12.5 mm graded stone aggregates as in padding over roof ,minimum thickness at khurra as 25mm maintain a slope of 1:100 mixed with water proofing compound as per manufacturers instructions complete all as specified and as directed by Engineer-in-charge. |
| 60 | Material and labour for cutting grooves in brick wall ,75 mm wide and 65 mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified and as directed by Engineer-in-charge. |
| 61 | Material and labour for cement concrete 1:2:4, type B-0 using 12.5 mm graded stone aggregates as inroof kerbs or mud stops/ coping etc including weathering slightly rounded or chamferred complete all as specified and as directed by Engineer-in-charge. |
| 62 | Material and labour for Providing and laying APP (Atactic polypropylene polymer) modified pre-fabricated five layer water proofing memorene 3 mm thick having weight not less than 3.60kg/sqm black finished reinforced with non wooven polymer matt fix after applying one coat of cold applied solvant based bituminious primer @ 0,40 ltrs per sqm using botane torch and sealing all joint etc confirming to IS 3488 and cement plaster 15 mm thick in cm 1:3 all as per manufacturer instruction complete all as specified and as directed by Engineer-in-charge. |
| 63 | Material and labour for cement concrete tiles 20cm x 20 cm x 25 mm thick , of cement concrete type B-1 type (1:2:4) set and pointed in neat cement slury laid over and including 15mm thick sceed bed inCM (1:4) complete all as specified and as directed. |
| 64 | Supply and fixing mild steel worklike Joist, channel, angle, or tee sections,fixed independently, without connecting plates,etc (cut to ordinary lengths i.e. with in 20mm of the length indicated. conforming to Fe 410-W (Gde-E-250) quality -A complete all as specified and as directed by Engineer-in-charge. |
| 65 | Supply and fixing mild steel framed work as in doors or gates of angles or other section with gussets plate rails braces etc complete drill for fixing of steel sheeting or other covering. Doors etc to be prepared for hanging or sliding with and incl either hook and hinges or steel hanging door fittingsteel sheeting or other covering, running railsand hanging also fastening and fixing complete incl pintel hinges, stops hand made sliding bolts etc conforming to Fe 410-O or Fe 310-O, including taking down old steel gate complete all as specified and as directed by Engineer-in-charge. . |
| 66 | Material and labour for preparation surfaces of any description over 10 cm girth or width,not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide on new surfaces of steel or iron complete all as specified and as directed by Engineer-in-charge. |
| 67 | Supply and fixingPVC ( SWR) rain water pipes 110 mm bore dia single socketed in any length with rubber ring joints fixed to walls with and includingflat iron clamps 25x3 mm for fixing and taking out old damaged AC rain water pipes complete all as specified and as directed by Engineer-in-charge. |
| 68 | Suppy and fixing PVC (SWR) bends of any radius for 110 mm bore dia rain water pipes with rubber ring joints complete all as specified and as directed by Engineer-in-charge. |
| 69 | Dismantling water storage tankexc 250 litres but n, exc 500litres capacity and removing to store or from site complete all as specified and as directed by Engineer-in-charge. |
| 70 | Supply and fixing Rotational moulded polythene water storage tank cylindrical vertical with closed top 500ltr capacity hoisted and fixed in position including Ball brass valves high pressure with polythene float and fly nuts for 20 mm bore all as specified in SSR Part-1 complete all as specified and as directed by Engineer-in-charge. |
| 71 | Supply and fixing in repair 125 mm size Brass chromium plated shower rose with armscomplete all as specified and as directed by Engineer-in-charge. |
| 72 | Supply and fixing in repairstop cock(concealed) cast copper alloy, chromium plated with crutch or butterfly handle screwed down screwed for 15mm bore dia pipe or brass ferrule complete all as specified and as directed by Engineer-in-charge. |
| 73 | Supply and fixing in repairBib tapscast copper alloy cromium plated with capstain head screwed down for 15 mm bore dia iron pipe or brass ferrule and fixed complete all as specified and as directed by Engineer-in-charge. |
| 74 | Supply and fixing in repairPillar taps Cast copper alloy, fancy type forhot and cold water mixture, with capstan heads chromium plated screwed down high pressure, screwed for 15mm bore dia iron pipeand fixedcomplete all as specified and as directed by Engineer-in-charge. |
| 75 | Supply and fixing in repair wall mixer cast copper alloy,chromium plated, fancy type for hot and cold water mixture with capstan heads chromium plated screwed down high pressure, screwed for 15mm bore dia iron pipe or brass ferrule and fixed complete all as specified and as directed by Engineer-in-charge. |
| 76 | Supply and fixing in repair Angle stop valve/ Angle valvecast copper alloy,chromium plated with capstan head , long shank and cup screwed down,screwed for 15mm bore pipe iron pipe or for brass ferrule complete all as specified and as directed by Engineer-in-charge. |
| 77 | Supply and fixing in repair450 mm long PVC connection with brass nuts on both ends for 15mm bore pipes of approved quality complete all as specified and as directed by Engineer-in-charge. |
| 78 | Supply and fixing in repair Viterous china, wash hand basin, white, flat back, size 550x400mm including PVC waste pipe 32mm bore and mild steel brackets, including cutting for or pinning in brackets complete all as specified and as directed by Engineer-in-charge. |
| 79 | Supply and fixing in repair 600mm x 450mmmirror of selected quality glass mounted on 6mm thick AC building board with alluminium frame all around hanging to wall with rawl plug and iron slits cup washers complete all as specified and as directed by Engineer-in-charge. |
| 80 | Supply and fixingin repair Tubular towel rail, brass chromium plated 20mm dia, D type ,60cm long between flanges complete all as specified and as directed by Engineer-in-charge. |
| 81 | Supply and fixing Shelf of PTMT fixed with and including Chromium plated brass screws and wooden /plastic cleats (Minimum weight 300gms)complete all as specified and as directed by Engineer-in-charge. |
| 82 | Supply and fixing in repairs PVC valveless syphonic action type,10 litres capacity,low level flushing cistern, white,with inlet,outet,float and handle , brackets ,PVC flush pipe 32 mm bore diaincluding 45cm long PVC connection with brass nut at both ends, stop cock of cast copper alloy, chromium plated,high pressure,screwed both ends , screwed for 15 mm bore dia iron pipe, complete all as specified and as directed by Engineer-in-charge. |
| 83 | Supply and fixing in repair Viterous china ware wash down water closet Padestalpatern with P trap including connection to flushing pipe, anti syphonage pipe etc complete all as specified and as directed by Engineer-in-charge. |
| 84 | Supply and fixing in repair glass self assembly consisting of 5.5 mm thick sheet glass self 12 cm wide with chromium plated bracket guard and ralling 60 cm long and fixed complete all as specified and as directed by Engineer-in-charge. |
| 85 | Supply and fixing in repair stainless steel Soap dishapprox size 160x160x90mm any type including fixed to plugs with CP brass screw complete all as specified and as directed by Engineer-in-charge. |
| 86 | Supply and fixing Health faucet with CP felxible pipe of 1.25metre long for 15mm bore iron pipe or unionincludingmaking connection and fixed in position complete all as specified and as directed by Engineer-in-charge. |
| 87 | Supply and fixing in repair 32mm bore waste fittings brass chromium plated for glazed ware sinks, basins etc with long screwed shanks and fly nuts, flange and bedded in red lead cement and other end fixed complete all as specified and as directed by Engineer-in-charge. |
| 88 | Supply and fixing in repairPVC 32mm dia flush pipe for low level cisterncomplete all as specified and as directed by Engineer-in-charge. |
| 89 | Material and labour for 75 mm thick cement concrete 1:3:6 type C-1 using 20 mm graded stone aggregateas in PCC path/ plinth protection etc finished the surfaces even and smooth with out using extra cement forming andincluding filling the joints complete all as specified and as directed by Engineer-in-charge. |
| 90 | Demolition of reinforced cement concrete of any description and in any position (Reinforecement cut as required to facilitate demolition )complete all as specified and as directed by Engineer-in-charge. |
| 91 | Material and labour for reinforcement cement concrete (Normal mix )1:2:4 Type B1 using 20mm graded aggregate as in slab support on wall , beams and coloums, in floor, roof landing, balconies deck slab and in shelves and the like complete all as specified and as directed by Engineer-in-charge.Note: Cost ofSteel props adjustable (Suspended/Supported) Scaffolding (6m -7 m) Hight , safety equipment for labours (Belt,hook,Helmet) shall deemed to be included in quoted rates . |
| 92 | Material and labourfor reinforcement cement concrete (Normal mix )1:2:4 Type B1using 20mm graded aggregate as Chajja and the likecomplete all as specified and as directed by Engineer-in-charge. . |
| 93 | Material and labour for Mild steel TMT bars 10mm dia and over cut to length bent to shape required including cranking , bending spirally for hooping for coloumns,hooking ends and binding with and including MS wire (anealed) not less than 0.9mm dia or securing with clipscomplete all as specified and as directed by Engineer-in-charge. |
| 94 | Material and labour for 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in jointed in cement morar 1:4 including pointing in white cement with admixture of pigment to match with shade of granite stone laid over and including 15mm thick screed bed or bedding layer in cement mortar (1:4) including grinding and polishing complete all as specified and as directed by Engineer-in-charge. |
| 95 | Material and labour for rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and as directed by Engineer-in-charge. |
| 96 | Material and labour for Pre polished Machine cut Kota stone slab flooring 20mm to 25 mm thick laid over and including 15 mm thick screed bed or bedding layer in cement mortar 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed by Engineer-in-charge. Note : in Steps Single piece shall only be used |
| 97 | Supply and fixing mild steel powder coated peg set of 6 fixed to wall with steel screwsincluding grinding and polishing complete all as specified and as directed by Engineer-in-charge. |
| 98 | Supply and fixing Stainless steelwall mounted kitchen platerack of size 750mm X600mm X 250 mm fixed on walls with sutiable arrangementcomplete all as specified and as directed by Engineer-in-charge. |
| 99 | Supply and fixing cast iron sand cast soil waste & vent pipe 100 mm bore in any length with or without ears with cement joints laid in trenches or in floor complete all as specified and as directed by Engineer-in-charge. |
| 100 | Supply and fixingcastironsand cast vent cowl for 100mm bore sand cast pipe complete all as specified and as directed by Engineer-in-charge. |
| 101 | Supply and fixing Cast ironfloor trap dia of outlet 75 mm with grating including jointing to waste pipefixed in cement mortar bedded in cement concrete (1:2:4) type B1 complete all as specified and as directed by Engineer-in-charge. . |
| 102 | Supply and fixing Cast iron P or S trap for 100 mm bore pipe jointed with cement mortar bedded in cement concrete (1:2:4) type B1complete all as specified and as directed by Engineer-in-charge. . |
| 103 | Supply and fixing cast iron Bends (any radius), diminishing pieces or tapers (larger bore measured) for 100mmbore cast iron pipe jointed with cement mortar complete all as specified and as directed by Engineer-in-charge. . |
| 104 | Supply and fixing cast ironBranch pieces, double/cross, T (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches for 100mm bore cast iron pipe complete all as specified and as directed by Engineer-in-charge. . |
| 105 | Supply and fixingStack clampsout of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts for100mm bore pipe and securing ends of stays to wall or roof complete all as specified and as directed by Engineer-in-charge. . |
| 106 | Supply and fixing Solid PVC door frame of size 50 mmx47 mm made out of 5 mm plain colour PVC sheet reinforced with M.S square tube, suppyling and fixing in opening as per specification and drg complete all as specified and as directed by Engineer-in-charge. . |
| 107 | Supply and fixing factory made solid panel PVC mouldeddoor shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails M.S. frame shall be covered with heat moulded plain colour PVC \"C\" channel having a PVC sheet strip of 20 mm width struck inside with solvent cement for stiles and plain colour of PVC sheet for top rail lock rail and bottom rail, on either side & gap insert for top rail bottom rail panelling of plain colour PVC sheets to be fitted in MS frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppying and fixing in the frame at site as per specification & drawing complete all as specified and as directed by Engineer-in-charge. . |
| 108 | Supply and fixing mild steel butt hinges medium weight cold rolled ,size 75mm complete all as specified and as directed by Engineer-in-charge. . |
| 109 | Supply and fxing aluminium, anodised, barrel tower bolts 100 mm long of extruded section and fixed complete all as specified and as directed by Engineer-in-charge. . |
| 110 | Supply and fixinganodised extruded aluminium alloy handles (D type), fabricated type of size100 mmcomplete all as specified and as directed by Engineer-in-charge. .d. |
| 111 | Demolition of cement concreteof any description andin any position not otherwise specifically provided (below or above ground level).complete all as specified and as directed by Engineer-in-charge. . |
| 112 | Materrial and labour for cement concrete 1:7:12 mix, type E-2 using 40mm graded Brick aggregate as in filling in sunken portion complete all as specified and as directed by Engineer-in-charge. . |
| 113 | Material and labour for applying three coats of brush bond acrylic based cementitious material of approved quality for sunken portion treatment all as per manufacturer instruction and providing 3 mm th APP membrain over 85/25 grade bitumen layer @ 0.5 kg /Sqm all complete all as specified and as directed by Engineer-in-charge. . |
| 114 | Material and labour for providing mild steel galvanised medium grade 40 mm bore dia GI pipe as spouts 50 cm long emcedded in cement motar complete all as specified and as directed by Engineer-in-charge. |
| 115 | Material and labourfor formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams,flat , for rough finished surfaces of concrete complete all as specified and as directed by Engineer-in-charge |
| 116 | Material and labour for formwork to chullah hoods, chajjas, troughs and similar items including edges,flat , for rough finished surfacesof concrete complete all as specified and as directed by Engineer-in-charge |
| 117 | Supply only Liquid water proofing compound |
| 118 | Supply and fixing in repair Gun metal globe or gate valveswith iron wheel head screwed both ends for 20 mm bore dia iron pipe complete all as specified and as directed by Engineer-in-charge |
| 119 | Taking down carefully copper/ aluminium point wiring (light fan socket or power) complete along with fittings such as switches, ceiling roses, Pendants regulators Tube fittings and other Kits & fittings/conduitfromsurface /wall .Removing the material from work site and making good the disturbed portion/ surface of wall/ floor/ ceiling etc by using cement mortar and colour/ white wash to match with the existing surface / location complete all as specified and as directed by Engineer-in-charge. Note:- Serviceable fitting / fixtures will be reused in the work as directed by Engineer- in-Charge) |
| 120 | Taking down un-serviceable main switch, DB’s insulators, DB for MCB etc of any type and any capacity and further disposal including making good the disturbed surface and matching the colour of wall with the existing colour wash / paint / distemper wherever required (as per the existing ) complete all as specified and as directed by Engineer-in-charge |
| 121 | Material and labour for taking down ceiling fan of any descrptions, servicing, rewinding, and complete repairs, painting of fan as required, fixing back, or fixing new ceiling fan for proper functioning, connecting and testing the fanfor its satisfactory function including making good the disturbed surface and matching the colour of wall with the existing colour wash / paint / distemper wherever required (as per the existing ) complete all as specified and as directed by Engineer-in-charge |
| 122 | Material and labour for taking down exhaust fan of any descrptions, servicing, rewinding, and complete repairs, painting of fan as required, fixing back, or fixing new exhaust fan for proper functioning, connecting and testing the fanfor its satisfactory function including making good the disturbed surface and matching the colour of wall with the existing colour wash / paint / distemper wherever required (as per the existing )complete all as specified and as directed by Engineer-in-charge |
| 123 | Material and labour for taking down elect water heater of any descrptions, servcing and complete repairs of geyser as required, painting outer body, fixing back, connecting and testing the geyser for its satisfactory functionincluding making good the disturbed surface and matching the colour of wall with the existing colour wash / paint / distemper wherever required (as per the existing ) complete all as specified and as directed by Engineer-in-charge |
| 124 | Material and labourfor point wiringwith FRLSPVC insulated unsheathed multi-stranded copper conductor 1.5 Sq.mm (nominal area ) single core cable 1100 Volt grade drawn in and Including new rigid non metallic concealed PVC Conduit of suitable size (not less than 20 mm) in wall , surface of ceiling with all fittings, such as tee, bend, elbow, socket etc including pressed steel sunken boxes/modular sunken (Terminal boxes) with earth dolly,duly galvanised, with white shade frame & cover plate of suitable module for modular switch / or sockets including FRLSPVC insulated unsheathed stranded copper conductor 1.5 Sq.mm (nominal area) single core cable as earth continuity conducter to common earth and connected to earth dolly, Including making good the disturbed portion of the wall complete all as specified and as directed by Engineer-in-charge, for the following :- 124.01One light/fan point controlled by one 1-way switch |
| 125 | One light/fan point controlled by two 2-way switch |
| 126 | One3/5 pin socket outlet, 5 Amp on independent board |
| 127 | One3/5 pin socket outlet, 5 Amp on same board |
| 128 | One bell /buzzerpoint controlledby one push button on independent board |
| 129 | Material and labour for point wiring with FRLSPVC insulated unsheathed multi-stranded copper conductor 2.5 Sq.mm (nominal area ) single core cable 1100 Volt grade drawn in and Including new rigid non metallic concealed PVC Conduit in wall, surface of ceiling with all fittings, such as tee, bend, elbow, socket etc including pressed steel/modular sunken boxes(Terminal boxes) with earth dolly,duly galvanised, with white shade frame & cover plate of suitable module for modular switch / or sockets including FRLSPVC insulated unsheathed stranded copper conductor 2.5 Sq.mm (nominal area) single core cable as earth continuity conducter to common earth and connected to earth dolly, Including making good the disturbed portion of the wall complete all as specified and as directed by Engineer-in-charge |
| 130 | Dismantling / Taking down existing unserviceable sub main wiring from batten / conduit of any size all as directed. Removing the material from work site and making good the disturbed portion/ surface of wall/ floor/ ceiling etc by using cement mortar and colour/ white wash to match with the existing surface / location complete all as specified and as directed by Engineer-in-charge. |
| 131 | Material and labour for sub main surface wiring with PVC insulated unsheathed copper conductor cable of size 6 Sqmm single core 1100 volt grade drawn in and Including new rigid non metallic concealed PVC conduit of suitable size (Not less than25mm dia)inwall and surface of ceiling including 6 Sqmm PVC insulated unsheathed copper conductor cable for continuous earthing form main earth dolly including makinggood the disturbedportion of wall.complete all as specified and as directed by Engineer-in-charge .Note :- Two run of 6 Sqmm copper cable one run of 6 Sqmm copper cable and PVC conduit will be measured as a single unit/length |
| 132 | Supply and fixing Switch Modular type, 6 Amp, 240 Volts , one way complete fixed complete all as specified and as directed by Engineer-in-charge |
| 133 | Supply and fixing Switch Modular type,6 Amp, 240 Volts , Two way complete fixed complete all as specified and as directed by Engineer-in-charge |
| 134 | Supply and fixing Switch Modular type, 16 Amp,240 Volts , one way complete fixed complete all as specified and as directed by Engineer-in-charge |
| 135 | Supply and fixing Socket outlet, Modular type, 6 Amp complete fixed complete all as specified and as directed by Engineer-in-charge |
| 136 | Supply and fixing Socket outlet, Modular type, 6&16 Amp complete fixed complete all as specified and as directed by Engineer-in-charge |
| 137 | Supply and fixing Bell Push, Modular type, 6 Amp complete fixed complete all as specified and as directed by Engineer-in-charge |
| 138 | Supply and fixing Fan regulator, modular type electronic step type complete complete all as specified and as directed by Engineer-in-charge |
| 139 | Supply and fixing ceiling rose surface bakelite two to three terminal 65x50 mm complete all as specified and as directed by Engineer-in-charge. |
| 140 | Supply and fixing in replacement Tube light fittings LED type 1x20 Watt4 ft long incl LED tube rod and incl 3 core flexible wire 0.75 Sqmm copper cable complete fixed complete all as specified and as directed by Engineer-in-charge |
| 141 | Supply and fixing in replacement Tube light fittings LED type 1X10 Watt, 2 ft long incl LED tube rod and incl 3 core flexible wire 0.75 Sqmm copper cable complete fixed complete all as specified and as directed by Engineer-in-charge |
| 142 | Supply and fixingLED bulk head ,10 W complete fixed complete all as specified and as directed by Engineer-in-charge |
| 143 | Supply and fixing Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings complete fixed complete all as specified and as directed by Engineer-in-charge |
| 144 | Supply and fixing LED Bulb 9 watt 230 volt retrofit type complete fixed complete all as specified and as directed by Engineer-in-charge |
| 145 | Supply and fixing in bellding dong operating on AC 230 volt single phase complete fixed complete all as specified and as directed by Engineer-in-charge. |
| 146 | Supply and fixing MCBDB SPN8 Waywith acrylic double doorcomplete fixed complete all as specified and as directed by Engineer-in-charge |
| 147 | Supply and fixing in replacement including flushing in wallMCB distribution board verticalTPN 4 way 415 Volts AC double door type sheet steel phosphotised powder painted with bus bar neutral earth bar including provision of MCB TPN, FP 100 Ampconforing to IP 43as incomer complete fixed complete all as specified and as directed by Engineer-in-charge |
| 148 | Supply and fixing MCCB 4 pole100Amp 415 voltwith breaking capacity of 16 KA complete all as specified and direceted. |
| 149 | Supply and fixing MCB SPN 240V 40 Amps C series 10 KA complete fixed complete all as specified and as directed by Engineer-in-charge. |
| 150 | Supply and fixing MCB SP 240V 6 to 32 Amps C series 10 KAcomplete fixed complete all as specified and as directed by Engineer-in-charge |
| 151 | Taking Down the KWH meteralong with wooden board/DB after removingall electricalconnection complete all as directed by Engineer in Charge. |
| 152 | Refixing&connecting the same KWH meter after complete repairs, wiring, elements& parts change as necessary or fixing new serviceable KWH energy meter for proper functioning complete all as directed by Engineer in Charge. |
| 153 | Supply and fixing Sheet metal enclosure factory made of size 20cm x 25cm x 12.5 cm deep box made out of 2mm thick ms sheet with double door with locking arrangement , epoxy power coated holes drilled for cable entries suitable for accomodating electric energy meterincluding brick/cement works as per site requirementincludiing flushing the box in walll and making good the disturbed portion of wall /surface complete fixed complete all as specified and as directed by Engineer-in-charge |
| 154 | Taking down old U/S LT UG cable of any size from trenches/pipe/floor/walls complete all as specified. |
| 155 | Supply,laying, jointing, testing and commissioning cable XLPEinsulatedPVC shetahtedstrip wire armoured1100 volt4 core 25 sqmm multi stranded aluminiumconductor laid in trenches / on walls /in ducts etc including necessary fixing arrangement such as cable lugs, glands etc complete including removing/taking out existing unsvcable complete all as specified and as directed by Engineer-in-charge |
| 156 | Excavation in trenches n.exc 1.5 mtr deep and n.exc 1.5 mtr wide for foundations,laying of pipes, cables etc as in soft loose soil and getting out complete fixed complete all as specified and as directed by Engineer-in-charge |
| 157 | Returning filling in soil including ,spreading,levelling,watering and well ramming in layers not exc 25cm thick each complete fixed complete all as specified and as directed by Engineer-in-charge |
| 158 | Removing excavated material soil to a distance not exc 50m and depositing where directed at a level not exc 1.5 m above the starting point complete fixed complete all as specified and as directed by Engineer-in-charge |
| 159 | Material and labour for laying/filling fine river sand 8 cm before laying the cable and 15 cm after laying the cable in trenches as cushioning to under ground cablescomplete all as specified and as directed by Engineer-in-charge |
| 160 | Supplying and laying factory made unreinforced Pre cast concrete cable covers, class LV, type 1 flat ofsize 250 x 150 x 40mmlaid in trenches as protection to cables complete all as specified and as directed. |
| 161 | Supply and fixing HDPE pipe of size50mmdiacompleteallas spcifed& directedby Engr-in-Charge. |
| 162 | Material and labour for earthing complete with galvanised steel earth plate electrode 60×60cm.× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less\"than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including PCC pit in PCC (1:3:6) type C1 cast iron frame 50 mm thick precastRCC 1: 1.5: 3) nominal mix cover slab reinforcedwith 8 mm dia mild steel deformed bar 15 cc and suitable handle of 10 mm dia round bar including necessary excavation earth work in soft/loose soil and disposal of soil to a distance not exceeding 50 m and funnel with watering pipe, wire mesh, copper lugs etc GI protection pipe of size 15 mm bore including testingcomplete all as specified and as directed by Engineer-in-charge |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2025 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
