|
| 1 | Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing), removing rubbish off the premises outside low laying area all as specified and directed by Engineer-in-Charge. |
| 2 | Demolition of un-reinforced cement concrete in ground floors and pavings not exceeding 15 cm thickness. |
| 3 | M & L 40 mm thick PCC 1:2:4 type B1 (Using 20mm graded granite stone aggregate) in sub base of floorings/ levelling course complete all as specified. |
| 4 | M & L for Screed bed or bedding layer of mortar 15mm thick for laying floor finishes in cement mortar 1:4 complete all as spd. |
| 5 | M&L,Vitrified Ceramic tiles light shade 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, infloors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade complete all as specified and as directed |
| 6 | -ditto- in skirting including 10mm thick backing coat in CM 1:3 complete all as specified and as directed. |
| 7 | S&F Non - skid joint free Ceramic colour tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to matchcomplete all as specified and directed. |
| 8 | M&L, joint free coloured glazed ceramic tilesof size 300 x 450mm, 6 to 7mm thick in dado etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile over and including 10mm thick backing coat in CM 1:3 complete all as specified and as directed. |
| 9 | Taking downcementor cement lime plaster on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc. |
| 10 | M & L for rendering 15mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 ,finished even and smooth (without using extra cement) complete all as specified |
| 11 | M&L for Preparing new plastered surfaces of walls and applyingtwo coats of oil bound distemper over a coat of primer over 2mm thick wall care putty complete all as specified and directed. |
| 12 | M&L for complete removal of existing treatment (upto plaster surface) of old painted surfaces and applying two coats of distemper oil emulsion on surfaces of walls overa coat of primer over 2mm thick wall care putty complete all as specified. |
| 13 | S&F Bib taps, cast copper alloy, chromium plated, fancy type long body, screwed down, screwed for iron pipe or for brass ferrule 15mm dia and fixed |
| 14 | M&L in repair for 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement |
| 15 | Demolition and breaking up drain pipescomplete all as specified. |
| 16 | S&F PVC(SWR) 75mm bore pipes single socketed in any length with rubber ring joints fixed to walls/floor |
| 17 | S&F PVC (SWR)bend 75mm bore complete all as specified and directed.. |
| 18 | Taking down Chowkats or frames not exceeding 1.5 Sqm each (Without taking off shutters from the frames) |
| 19 | Taking down Chowkats or frames exceeding 1.5 Sqm but not exceeding 4 Sqm each (Without taking off shutters from the frame) |
| 20 | S&F 12mm thick toughened glass door including all fitting/fixtures, locking arrangements, handles, auto closing hinges etc complete all as specified and directed. |
| 21 | Supply & Fix aluminium Powder coated (minimum thickness of powder coating 50 micron) frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing , fixing arrangements for frame etc complete all as specified and directed |
| 22 | Anodised aluminium door shutter, aluminium section weighing 0.55 Kg per M including necessary jointing cleats, glazing clips rubber neoprene packing, handles 2 nos in each door, hinges, anodised aluminium snap beading screws etc complete all as specified Note : Glasswill be measured and paid seperately under relevant item |
| 23 | S & F Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty complete all as specified. |
| 24 | S&F Providing and fixing factory made uPVC white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. 4mm thick glazing with plain glass ,Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories. (Note: The unit rate quoted by contractor includes cost of glass, wire cloth and all other connected accessories. Net Opening will be measured lor payment purpose.) (A) Area not exceeding 2.00 sqm each |
| 25 | M&L for Sheet glass, 5.5mm thick ordinary quality and glazing with oil putty in square exc 0.5 sq. m in each pane complete all as specified |
| 26 | S&F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples |
| 27 | S&F 300mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy. |
| 28 | S & F 100 mm long medium weight, stain less steel Butt hinges complete. |
| 29 | M&L, 18 to 20mm thick, approved machine cut, coloured Granite, factory polished, edges rounded in steps, cooking platform and the like laid over and including screed bed or bedding layer 20mm thick in cement mortar 1:4, pointing with white cement (1:2) using marble dust with admixture of pigment to match the shade of granite stone complete all as specified and directed. |
| 30 | Dismantling of wall boards (fibre, Pulp, insulation, plywood etc.) as in cup boards, shelve, pelmet boxes etc. |
| 31 | S & F Second class hard wood plain fillets square, rectangular or triangular in section, wrought secured with screws, cross sectional area exceeding 13 and not exceeding 25 Sq. cm |
| 32 | M&L for 18/19 mm thick Medium density fibre board exterior grade complete all as specified and as directed by Enginner-in-Charge. |
| 33 | M&L for 12mm thick Medium density fibre board exterior grade complete all as specified and as directed by Enginner-in-Charge. |
| 34 | Extra over rates of block board or veneered particle board or plywood for external teak wood lipping, 6mm thick fixed with nails 18 mm thick all as specified and directed |
| 35 | M&L for 0.9 mm thick Decorative laminate type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer\"s instructions |
| 36 | Supply only stainless steel acessories suitable for kitchen cabinets as under:- |
| 37 | (a)Stainless steel basket (plain) of size 50cmx37cmx16cm made of 4mm th S.S.wire approved quality with suitable arrangement for fixing Telescope basket (channel) 18/20 inch length two wayextruded MS galvanised over rollers of approved make. |
| 38 | (b)Stainless steel thalibasket (11-13 division) of size 50cmx37cmx20cm made of 4mm th S.S.wire approved quality with suitable arrangement for fixing Telescope basket (channel) 18/20 inch length two wayextruded MS galvanised over rollers of approved. |
| 39 | (c)Stainless steel Platebasket (11-13 division) of size 50cmx37cmx16cm made of 4mm th S.S.wire approved quality with suitable arrangement for fixing Telescope basket (channel) 18/20 inch length two wayextruded MS galvanised over rollers of approved. |
| 40 | (d)Stainless steel Partition basketof size 50cmx37cmx16cm made of 4mm th S.S.wire approved quality with suitable arrangement for fixing Telescope basket (channel) 18/20 inch length two wayextruded MS galvanised over rollers of approved make. |
| 41 | (e)Stainless steel Cutlary basketof size 50cmx37cmx10cm made of 4mm th S.S.wireand bottom of S S perforated sheet approved quality with suitable arrangement for fixing Telescope basket (channel) 18/20 inch length two wayextruded MS galvanised over rollers of approved make. |
| 42 | S&F soft closer telescopic drawer channel of any lengthof bearing 40kg capacitywith 100% extension strong and smooth operation for wooden and metal drawers in kitchen,ward robe etc as per requirement allas specified and as directed. Make : Godrej or equivalent |
| 43 | S&Fcabinetauto hinges soft close 4 hole full over lay suitable for 14-25 mm thick panel with 105 degree opening suitable for as in kitchen drawers and cupboards. all as specified and as directed by engineer in charge Make :Godrej , Hettich or equivalent |
| 44 | S & F100 mm long brass handle cast type polished bright finish complete |
| 45 | Demolition of cement concrete (unreinforced) of any description and in any position and disposed off to a distance exc. 500 mtrs and not exc.1.50 km all as directed by EIC. |
| 46 | M&L 100mm thick PCC 1:4:8, type D-2 (40 mm graded agg) as in sub base and similar work complete all as directed. |
| 47 | M&L sand filling under floors of interlocking tiles including watering and consolidation |
| 48 | M&Lmachine pressed precast concrete with grey cement and pigmentinterlocking paverblock anyshapeand size confirming to IS-15658- 2006 of 60 mm thickness M 35 grade with gray cement all as directed. |
| 49 | M&L for 20 mm thick screed bed or bedding layer in CM 1:6 complete all as specified and directed. |
| 50 | M&L Chequered cement concrete coloured tiles 30 cm x 30 cm x 25 mm thick with grey pigment cement andpigmenst set ionted and pointed in neat cement slurry colour to match in floors . |
| 51 | Material and labour PCC 1:2:4 type B0 (using 12.5 mm graded stone aggregate) as in copings all as specified and directed. |
| 52 | Surface excavationnot exceeding 30 cm deep and averaging 15 cm deep & getting out in all type soil complete all as specified.any type of soil |
| 53 | Excavation in trenches, not exceeding 1.5 M wide and not exceeding 1.5 M depth for foundation, etc., and getting out any type of soil. |
| 54 | M&L for PCC 1:4:8 type D-2 (40mm graded aggregate) in foundation filling and mass concrete. |
| 55 | M&L for Formwork to sides of rough finished surfaces of flat concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter all as specified. |
| 56 | M&L for use and waste Formwork tosides of pillars, post, stuts, coloumn and stanchions rough finished surfaces of concrete square, rectangular or polygonal complete all as specified. |
| 57 | M&L for use and waste Formwork to rough finished surfaces of sides and soffits of floor or roof beam, beam haunching, lintels, cantilevers, shelves including supports, overhangs etc complete all as specified |
| 58 | M&L TMT bars 10mm dia and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hookings ends and binding with mild steel (annealed ) not less thank 0.9 mm dia or securing with clips as specified. |
| 59 | M&L TMT bars 6mm to 8mm dia cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hookings ends and binding with mild steel (annealed ) not less thank 0.9 mm dia or securing with clips as specified. |
| 60 | M&L Reinforced Cement concrete Nominal Mix, Type B1 1:2:4 (20 mm graded stone aggregate) in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc; basement slabs, under reamed piles and mass concrete |
| 61 | M&L for RCC Nominal Mix, Type B1 1:2:4 (using 20 mm grade stone aggregate) for columns, pillars, piers, posts and struts etc all as specified |
| 62 | M & L for RCC Nominal Mix, Type B1 1:2:4 (using 20mm graded stone aggregate) for lintel Beams catileveres bressummers, lintels over 1.5m span and similar work complete all as specified and directed |
| 63 | M&L for mild Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes Fe 410-W (Gde-E-250 quality-A) conforming to I. S.1161- 1979 grade St.-240 complete all as specified and as directed. |
| 64 | M&L Plate (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment |
| 65 | S&FMild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 5cm but not exc 10cm long |
| 66 | S & F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding and Ridge to wall, fixed with self tapping screws all as specified and directed. |
| 67 | M&L for Preparation of New previously untreated steel surfaces of any description and priming with Red oxide, zinc chrome and applying two coats of synthetic enamel paint over 10cm in width or girth, not otherwise described. |
| 68 | M&L for Broken stone or boulders hardcore of gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15cm thick, watered and rammed to a true surface complete all as specified and as directed. |
| 69 | M&L for Cement concrete type B-1, 1:2:4 (20mm graded aggregate) of 50 mm thick as in floor finishes, complete all as specified and as directed. |
| 70 | M&L for Forming 12mm thick 100 deep Expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound,Grade ‘A’ |
| 71 | Removing the excavated soil to a distance n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point. |
| 72 | M&L Brick work with fly ash brick, straight or curved on plan exc 6m menan raidus, built in CM 1:6 all as specified. |
| 73 | Rendering 15 mm thick cement plaster on fair surfaces of brick work or concrete surfaces in CM 1:4 finished to even and smooth surfaces in without using extra cement etc complete all as specified and directed. |
| 74 | Preperaing new plastered surfaces of wall and applying two coats of cement base paint over a coat of cement primer all as specified. |
| 75 | M&L for Sub main wiring with two runs of single core 4 Sqmm multi stranded copper conductor PVC insulated unsheathed, FRLS Cable, 1100 Volts grade and one run of 2.5 Sqmm multi stranded copper conductor cable as earth continuity conductor drawn into and including non metalic ridig surface / recessed PVC conduit/casing caping,not less than 25 mm dia conduit accessories including taking out existing complete all as specified and as directed.Note:Two runs of 4.0 Sqmm copper cable, one run 4 Sqmm copper cable for earth wire and one run of PVC conduit shall be measured as one unit length. |
| 76 | M&L for Sub main wiring with two runs of single core 6 Sqmm multi stranded copper conductor PVC insulated unsheathed, FRLS Cable, 1100 Volts grade and one run of 4 Sqmm multi stranded copper conductor cable as earth continuity conductor drawn into and including non metalic ridig surface / recessed PVC conduit/casing caping, not less than 25 mm diaconduit accessoriesincluding taking out existingcomplete all as specified and as directed.Note: Two runs of 6.0 Sqmm copper cable, one run 6 Sqmm copper cable for earth wire and one run of PVC conduit shall be measured as one unit length. |
| 77 | M&L for Sub main wiring with two runs of single core 10 Sqmm multi stranded copper conductor PVC insulated unsheathed, FRLS Cable, 1100 Volts grade and one run of 6 Sqmm multi stranded copper conductor cable as earth continuity conductor drawn into and including non metalic ridig surface / recessed PVC conduit/casing caping, not less than 25 mm diaconduit accessoriesincluding taking out existingcomplete all as specified and as directed.Note: Two runs of 10 Sqmm copper cable, one run 6 Sqmm copper cable for earth wire and one run of PVC conduit shall be measured as one unit length. |
| 78 | Supply and fix socket outlet6/16 Amps, 6 in 1, Modulartype. |
| 79 | Supply and fix switch piano modulartype,15/16 Amps 240 volts single pole one way. |
| 80 | Supply and fix modular plates with frame and PVC boxwhite colourof 10 module complete all as specified and as directed |
| 81 | Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete,(fittings such as switches, ceiling roses,pendants, regulators sockets etc. to be measuredseparately), removing materials to store for keeping in safe custody for reuse at site and making gooddisturbed surfaces of walls, floors, etc. complete all as specified. |
| 82 | M& L for point wiring complete with 1.5 sqmm single core PVC insulatedunsheathed FRLS cable 1100 volts grade ISI marked with multi stranded copper conductor drawn through existing conduit/PVC Caping and casing and accessories ISI marked including provision of 1.5 sqmm PVC insulatedmultistranded unsheathed copper conductor cable FRLS ISI marked as earth continuity conductor, fabricated Modular steel sunken terminal box duly painted made out of 1.60mm thick MS sheet concealed in walls, with brass/chromium platedscrews and cup washers for housingModular switches, socket outlets, fan regulators etc, all as specified and as directed for One light Point controlled by oneway switch |
| 83 | All as per Ser item No 77 above but for One Ceiling /Exhaust Fan Point controlled by one one way switch. |
| 84 | All as per Ser item No 77 above but for 5 amps socket point on independent board. |
| 85 | All as per Ser item No 77 above but with 2.5 sqmm cable for 15 Amps socket outlet on independent board with 2.5 Sqmm earth continuty wire complete all as specified and directed. |
| 86 | All as per Ser item No 77 above but with 4 sqmm cable for 20/25 Amps socket outlet on independent board with 4 Sqmm earth continuty wire complete all as specified and directed.( For UPS and Acs) |
| 87 | Supply and fixceiling rose surface backelite three terminals, PVC/polycarbonate, insulated body. |
| 88 | Supply and fix switch piano modulartype, 6 Amps 240 volts single pole one way. Make:- Anchor /Havells |
| 89 | Supply and fix socket outlet, 5 pin 6 Amps, Modulartype. Make :- Anchor /Havells |
| 90 | Supply and fix modular plates with frame white colour3 module |
| 91 | Supply and fix modular plates with frame white colour4 module |
| 92 | Supply and fix modular plates with frame white colour6 module |
| 93 | Supply and fix modular plates with frame white colour8 module |
| 94 | Supply and fix stepped type fan regulator electronic modulartype, 2 module,240 Volt. Make Havells /Anchor |
| 95 | Supply and fix in repair surface mounting LED 2ft x2ft luminaire of capacity 36W with white powder coated CRCA housing with LEDs and full window acrylic diffuser etc.complete with all acessories internally prewired suitable for sigle phase 230volts 50Hz AC supply including connecting up with flexible copper conductor cable of size 0.5 Sqmm (nominal area) complete all as specified.Make : Make -Crompton,or equivalent fromPhilips / Wipro/Havells. |
| 96 | S&F Exhaust Fan of Size 450mm Sweep, Steel body, AC Single Phase. 230 Volt with Blades, Frame and Louvers, Providing Connection with and including 3 Core Flexible Copper Conductor Cable of suitable Size and Length , complete all as specified and as directed.Make : Usha or equivalent model in Havells/ Orient |
| 97 | M&L Cutting Holes in Brick Walling,for inserting of exhaust fan. and Making Good to Dismantled portion with Cement Concrete 1:2:4 (20mm graded stone aggregates) or Cement Mortar 1:3 (as required) and Adjoining Surfaces in Cement Mortar 1:4, complete all as specified and as directed. |
| 98 | Supply and fix MCB protected POWER UNIT with one 25 amps socket, (incl 3 Pin Plug Top)including MCB 25 Amps rating with six module plate and flush metal GI box and electrically connecting up fixed in repair complete all as specified and directed of Make Havells cat No. DBOXX (25 Amps) OR any equivalent model in Legrand / L & T. |
