Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Schedule \"A\" |
| 2 | Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles and rubbish off the premises, complete all as specified and directed by Engineer-in-Charge. |
| 3 | Demolition of stone slabs and tiles of any description or thickness in floors, aprons Laid, bedded and pointed in any mortar etc., complete all as specified and directed by Engineer-in-Charge. |
| 4 | Taking down Chowkhat with shutters (without taking of shutters from the frames of any description not exceeding 1.5 Sqm in each panel, complete all as specified and directed by Engineer-in-Charge. |
| 5 | Taking down Chowkhat with shutters (without taking of shutters from the frames of any description exceeding 1.5 Sqm but not exceeding 4.0 sqm in each panel, complete all as specified and directed by Engineer-in-Charge. |
| 6 | Demolition of Concrete of any description and in any position not otherwise specifically provided, complete all as specified and directed by Engineer-in-Charge. |
| 7 | Dismantling/ Demolition of brick work or stone masonry or RCC Pre cast Jali & Jafari built in cement mortar including all quoins, arches, pillars, etc., complete all as specified and directed by Engineer-in-Charge. |
| 8 | Taking down cement plaster on stone wall including racking out joints, hacking for key scrubbing with water etc., complete all as specified and directed by Engineer-in-Charge. |
| 9 | Taking up or down 15mm bore dia., steel tubing & connections including cleaning for re-fixing or removal to store, complete all as specified and directed by Engineer-in-Charge. |
| 10 | Taking up or down for 20mm bore steel water tubing galvanised with connection, complete all as specified and directed by Engineer-in-Charge. |
| 11 | Taking up or down for 25mm bore steel water tubing galvanised with connection, complete all as specified and directed by Engineer-in-Charge. |
| 12 | Dismantling water tanks of capacity of 1000 litres removing to store, complete all as specified and directed by Engineer-in-Charge. |
| 13 | Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided, complete all as specified and directed by Engineer-in-Charge. |
| 14 | Taking down eaves gutter or RWP of any description, Including fittings, complete all as specified and directed by Engineer-in-Charge. |
| 15 | Demolition and breaking up drain pipes (SGSW, AC or RCC) of internal dia 150mm, set in cement mortar, complete all as specified and directed by Engineer-in-Charge. |
| 16 | Supply & Fixing 2nd class HW plain Chowkhat and framed, rebated on the solid rounded or chamfered put together with glue pinned at joints, complete all as specified and directed by Engineer-in-Charge. |
| 17 | Supply & Fixing 35mm thick Second class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded, fitted with cut mitred beads for securing glass etc. as specified in SSR Part I, Section 8, clause 8.20 (a), complete all as specified and directed by Engineer-in-Charge. |
| 18 | Supply & Fixing 35mm thick Flush Shutter, solid core construction, with block board core and plywood face panels, bothface is covered with decorative face veneer with lipping/ frame to match commercial type on both side, complete all as specified and directed by Engineer-in-Charge. |
| 19 | Supply & Fixing Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, supplying & fixing in opening as per specification & drawing, complete all as specified and directed by Engineer-in-Charge. |
| 20 | Material & Labour for Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing, complete all as specified and directed by Engineer-in-Charge. |
| 21 | Material & Labour for 18-19mm thick factory made 100% solid WPC (Wood polymer composite) Solid Plain / Prelam / Enrouted Plain / Enrouted Painted flush Door Shutter of required size comprising of Virgin PVC resin of K Value 57-60 (Suspension Grade), Calcium carbonate and natural fibres (Wood Powders / rice husk / Wheat husk) and Non-toxic additives made from Extrusion process WPC foam sheet single Extruded (Inner) with density not less than 650 Kg/cbm manufacture by an ISO 9001-2015 Certified Company, having good screw holding capacity (Screw withdrawal strength of 2000 N (face) & 1100 N (Edge), Minimum Compressive Strength of 50 N/mm2, Modulusof elasticity 850N/mm2 and resistance of spread flame of Class A category with Property of being Termite/Borer Free, Water/Moisture Proof, Fire Retardant and fixing with Stainless Steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws for WC / Bathroom / Toilet / Kitchen / Balcony Doors, complete all as specified and directed by Engineer-in-Charge. |
| 22 | Supply & Fixing factory made uPVC white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+-0.2mm). Window profile with hollow section with multi chamber, frame (88mm x 52mm), sliding sash (42mm x 67mm), sliding interlock (one vertical length in each shutter) (45.5mm x 28mm), glazing bead (24.5mm x 16mm) will be metered cut and fusion welded at all corners, including railing of holes for fixing hardware and drainage of water ets, making arrangement for fixing of hardware, EPDM gasket. 1.2 +- 0.2mm thick galvanized steel frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm) 2nos, sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100m long fastener. Hardware (touch lock of zinc alloyed (white powder coated), steel roller system, stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories, complete all as specified and directed by Engineer-in-Charge. Note: The unit rate excludes cost of glass and includes all other connected accessories) area not exceeding 2.00 sqm each fixed from ground floor to any height of floors. |
| 23 | Supply & Fixing 7mm thick aluminium grills of make \"Deco grill\" model DG 104 surrounded by aluminium \"C\" channel and size of opening 75mm x 75mm all as specified and directed fixed from ground floor to any height of floors, complete all as specified and directed by Engineer-in-Charge. |
| 24 | Supply & Fixing factory made uPVC white colour fixed window/ventilator made of extruded profile with wall thickness of 2.3mm (+-2mm). Window profile with hollow section with multi chamber. Frame (60mm x 58mm). T profile (one vertical length in between two shutters) (60mm x74mm). Glazed bead (35mm x 20mm) will be mitered cut and fusion welded at all corners. Including drilling of holes for fixing hardware and drainage of water etc. making arrangement for fixing of hardware, EPDM gasket. 1.2 +-0.2mm thick. Galvanized steel frame (28mm x 21.5mm), T profile (27mm x 17mm) to be inserted in repair profile. Frame will be fixed to the wall with 8mm x 100mm long fasteners. 5mm thick glazing with selected quality glass, complete all as specified and directed by Engineer-in-Charge. Note: The unit rate excludes cost of glass and includes all other connected accessories, area not exceeding 1.00 sqm each fixed from ground floor to height of any floors. |
| 25 | Material & Labour for Preparation of new or previously treated wood surfaces of any description, over 10 cm width or girth, not otherwise described applying one coat of pink primer and applying two coat of synthetic enamel paint, complete all as specified and directed by Engineer-in-Charge. |
| 26 | Supply & Fixing 300mm long brass ordinary rat tail rod pattern springs including roller and roller, complete all as specified and directed by Engineer-in-Charge. |
| 27 | Supply & Fixing 100mm long Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21, complete all as specified and directed by Engineer-in-Charge. |
| 28 | Supply & Fixing 150mm long Extruded Aluminium alloy handles, fabricated type, and anodised, complete all as specified and directed by Engineer-in-Charge. |
| 29 | Supply & Fixing 150mm long Aluminium, anodised, barrel tower bolts of extruded section, complete all as specified and directed by Engineer-in-Charge. |
| 30 | Supply & Fixing 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast Aluminium alloy, complete all as specified and directed by Engineer-in-Charge. |
| 31 | Supply & Fixing Hasp and staple for 100mm, safety type, aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws, complete all as specified and directed by Engineer-in-Charge. |
| 32 | Supply & Fixing 140mm long aluminium anodized floor door stopper double legged with rubber shoe, fixed to bottom rail of door, complete all as specified and directed by Engineer-in-Charge. |
| 33 | Supply & Fixing 5mm thick Figured glass, pin headed type and glazing with oil putty in squares not exceeding 0.5 Sqm in each pane, complete all as specified and directed by Engineer-in-Charge. |
| 34 | Supply & Fixing stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium/pvc sections, complete all as specified and directed by Engineer-in-Charge. |
| 35 | Material & Labour 10mm thick vitrified tile of area exceeding not exceeding 0.36 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over screed bed or bedding layer of mortar 15mm thick with Cement Mortar 1:6, complete all as specified and directed by Engineer-in-Charge. |
| 36 | Material & Labour for 10mm thick vitrified tile of area exceeding not exceeding 0.36 sqm in vertical surfaces set and jointed in neat cement slurry and pointed in white or coloured cement to match over cementmortar 15mm thick with Cement Mortar 1:4, complete all as specified and directed by Engineer-in-Charge. |
| 37 | Material & Labour for PCC (1:2:4) type B-0 using 12.5mm graded aggregate as in floor of average 25mm thick, complete all as specified and directed by Engineer-in-Charge. |
| 38 | Material & Labour for 75mm thick cement concrete type C–1, (1:3:6) using 20mm graded stone aggregate as in plinth protection etc., complete all as specified and directed by Engineer-in-Charge. |
| 39 | Material & Labour for Non-skid ceramic coloured tiles 7 to 8mm thick (square / rectangular) area of each tile not exceeding 0.11 sqm in floors, over and including 15mm thick screed in Cement Mortar (1:4) set and jointed in neat cement slurry and pointed with white or coloured cement to match, complete all as specified and directed by Engineer-in-Charge. |
| 40 | Material & Labour for Glazed ceramic tiles in vertical surface 350 x 250 x 7 mm / 450 x 300 x 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match and including 15mm cement plaster in 1:4 CM, complete all as specified and directed by Engineer-in-Charge. |
| 41 | Material & Labour for granite (of any type) 20mm thick (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including, grinding, polishing, moulding the edges and polishing and including over screed bed 20mm thick in cement mortar 1:6, complete all as specified and directed by Engineer-in-Charge. |
| 42 | Material & Labour for precast RCC 1:2:4 Type-B1 (using 20mm graded crushed stone aggregate) as in manhole and drain cover slab and similar article with plain faces, set in Cement Mortar 1:4, complete all as specified and directed by Engineer-in-Charge. |
| 43 | Material & Labour for Porbandar stone masonry well bonded, bedded and solidly hearted built in Cement Mortar 1:6, complete all as specified and directed by Engineer-in-Charge. |
| 44 | Material & Labour for rendering 5mm thick on ceiling concrete surfaces in cement mortar 1:3 and even and smooth without using extra cement, complete all as specified and directed by Engineer-in-Charge. |
| 45 | Material & Labour for rendering 15mm thick on stone/brick/concrete surfaces in cement mortar 1:4 and even and smooth without using extra cement, complete all as specified and directed by Engineer-in-Charge. |
| 46 | Material & Labour for 15mm thick rendering in Cement Mortar 1:6 to stone surfaces trowelled to even & smooth w/o using extra cement, complete all as specified and directed by Engineer-in-Charge. |
| 47 | Material & Labour for preparing surfaces plastered or un-plastered new surface of walls applying two coats of oil bound distemper over a coat of primer over layer of smooth Putty finish as per manufacture instruction with smooth roller finish, complete all as specified and directed by Engineer-in-Charge. Note:- After painting, cleaning of all floors, glass & Furniture by own arrangement. |
| 48 | Material & Labour for complete removal of existing treatment by washing down and smoothing old surface of walls including scrapping and applying two coats of oil bound distemper over a coat of primer over layer of smooth Putty finish two coats as per manufacture instruction with smooth roller finish, complete all as specified and directed by Engineer-in-Charge.Note:- After painting, cleaning of all floors, glass & Furniture by own arrangement. |
| 49 | Material & Labour for preparing surfaces plastered or un-plastered new surface of ceiling applying two coats of oil bound distemper over a coat of primer on smooth putty finish two coats as per manufacture instruction with smooth roller finish, complete all as specified and directed by Engineer-in-Charge. Note:- After painting, cleaning of all floors, glass & Furniture by own arrangement. |
| 50 | Material & Labour for preparing surfaces plastered or un-plastered old surface of ceiling applying two coats of oil bound distemper over a coat of primer two coats as per manufacture instruction with smooth roller finish, complete all as specified and directed by Engineer-in-Charge. Note:- After painting, cleaning of all floors, glass & Furniture by own arrangement. |
| 51 | Material & Labour for complete removal of old plastered surfaces of wall and applying two coats of 100 % Premium acrylic emulsion paint having VOC less than 50 gm/ltrs and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over a coat of smooth putty all as per the manufacturer’s instructions, complete all as specified and directed by Engineer-in-Charge. |
| 52 | Material & Labour for preparation of new plastered surfaces of wall and applying two coats of 100 % Premium acrylic emulsion paint having VOC less than 50 gm/ltrs and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over a coat of smooth putty all as per the manufacturer’s instructions, complete all as specified and directed by Engineer-in-Charge. |
| 53 | Supply & Fixing PVC Floor trap 75mm bore with grating including jointing using solvent cement to waste pipe fixed in cement concrete type B-1 (1:2:4), complete all as specified and directed by Engineer-in-Charge. |
| 54 | Supply & Fixing PVC (SWR) gully trap 125/110mm, setting and jointing with solvent cement fixed in cement concrete type B-1 (1:2:4), complete all as specified and directed by Engineer-in-Charge. |
| 55 | Supply & Fixing 110mm dia PVC rain water pipe of pressure single socketed with rubber joint, jointed with solvent joint fixed to wall, complete all as specified and directed by Engineer-in-Charge. |
| 56 | Supply & Fixing 110mm dia PVC band any radius, complete all as specified and directed by Engineer-in-Charge. |
| 57 | Supply & Fixing PVC (SWR) pipes 110mm bore single socketed in any length with rubber ring joints fixed to walls, complete all as specified and directed by Engineer-in-Charge. |
| 58 | Supply & Fixing PVC (SWR) pipes 75mm bore single socketed in any length with rubber ring joints fixed to walls, complete all as specified and directed by Engineer-in-Charge. |
| 59 | Supply & Fixing PVC (SWR) pipes 110mm bore single socketed in any length with rubber ring joints laid in trenches, complete all as specified and directed by Engineer-in-Charge. |
| 60 | Supply & Fixing PVC (SWR) pipes 75mm bore single socketed in any length with rubber ring joints laid in trenches, complete all as specified and directed by Engineer-in-Charge. |
| 61 | Supply & Fixing PVC (SWR) bends 110mm bore with/without access door any radius, complete all as specified and directed by Engineer-in-Charge. |
| 62 | Supply & Fixing PVC (SWR) bends 75mm bore with/without access door any radius, complete all as specified and directed by Engineer-in-Charge. |
| 63 | Supply & Fixing PVC (SWR) single junction \"T\" 75mm bore with access door any radius, complete all as specified and directed by Engineer-in-Charge. |
| 64 | Supply & Fixing PVC (SWR) single junction \"T\" 110mm bore with access door any radius, complete all as specified and directed by Engineer-in-Charge. |
| 65 | Supply & Fixing PVC (SWR) vent cowl 110mm dia., complete all as specified and directed by Engineer-in-Charge. |
| 66 | Supplying and laying of 16mm dia CPVC pipes SDR 11 & fittings on walls/ceilings or laying in floors, complete all as specified and directed by Engineer-in-Charge. |
| 67 | Supplying and laying of 20mm dia CPVC pipes SDR 11 & fittings on walls/ceilings or laying in floors, complete all as specified and directed by Engineer-in-Charge. |
| 68 | Supplying and laying of 25mm dia CPVC pipes SDR 11 & fittings on walls/ceilings or laying in floors, complete all as specified and directed by Engineer-in-Charge. |
| 69 | Supply & Fixing Brass Elbow for special fitting of 16mm bore CPVC pipe, complete all as specified and directed by Engineer-in-Charge. |
| 70 | Supply & Fixing Brass Tee for special fitting of 16mm bore CPVC pipe, complete all as specified and directed by Engineer-in-Charge. |
| 71 | Supply & Fixing Male Brass threaded Adaptor Tee for special fitting of 16mm bore CPVC pipe, complete all as specified and directed by Engineer-in-Charge. |
| 72 | Supply & Fixing in repair 15mm bib tap (fancy type), cast copper alloy chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule, complete all as specified and directed by Engineer-in-Charge. |
| 73 | Supply & Fixing in repairs brass CP shower rose 125mm size fancy type with swivel joint any size including fixing to steel pipe/union for 15mm dia., complete all as specified and directed by Engineer-in-Charge. |
| 74 | Supply & Fixing in repair PVC connection of 15mm dia length 600mm, complete all as specified and directed by Engineer-in-Charge. |
| 75 | Supply & Fixing in repair Vitreous China wash down water closet pan (pedestal pattern), white with P or S trap with and including plastic water closet seat cover, connection to trap, flushing pipe & anti -syphonage pipe etc including necessary materials for fittings &making good to floor, complete all as specified and directed by Engineer-in-Charge. |
| 76 | Supply & Fixing in repair Vitreous China Squatting pan pattern \"long pan\" size 580mm, white with P or S trap with and including, connection to trap, flushing pipe & anti-syphonage pipe etc including necessary materials for fittings &making good to floor, complete all as specified and directed by Engineer-in-Charge. |
| 77 | Supply & Fixing for in repairs 10 Ltrs. Capacity PVC valve less, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets slim line or equivalent make / model with all accessories, complete all as specified and directed by Engineer-in-Charge. |
| 78 | Supply & Fixing for in repair Vitreous China ware wash hand basin white, oval type, size 550mm x 400mm size with cutting for and pinning ends of brackets or erecting stand including, chromium plated 15mm pillar cock, PVC connection 450mm long, CP waste coupling, 32mm dia PVC pipe, complete all as specified and directed by Engineer-in-Charge. |
| 79 | Supply & Fixing in repair Vitreous China bowl urinal flat back, size of 465mm x 355mm x 265mm white (minimum), with grating and union for discharge pipe complete including providing and fixing plugs bedding urinal against wall in Cement Mortar 1:2 securing urinal to plug including 60mm long brass screws, pointing around urinal back in Cement Mortar, fixing automatic flushing cistern with bracket, flush pipe, grating and union for discharge pipe, complete all as specified and directed by Engineer-in-Charge. |
| 80 | Supply & Fixing in repair Bevelled edge mirror, 600mm x 450mm of selected quality glass, mounted on 6mm thick or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers, complete all as specified and directed by Engineer-in-Charge. |
| 81 | Supply & Fixing in repair stainless steel 6 Pin cloth hanger wall mounted having length 30 cm, fancy type, complete all as specified and directed by Engineer-in-Charge. |
| 82 | Supply & Fixing in repair 20mm Aluminium anodised Tubular towel rail, 20mm dia, D type, 60cm long between flanges, and complete all as specified and directed by Engineer-in-Charge. |
| 83 | Supply & Fixing in repair 15mm dia CP Health Faucet with 1mtr long lead fixed in pipe, complete all as specified and directed by Engineer-in-Charge. |
| 84 | Supply & Fixing 1000 Ltrs. Capacity rotational moulded polyethylene water storage tanks (cylinder vertical with class top) hoisted including 25mm ball valve and fixed in position, complete all as specified and directed by Engineer-in-Charge. |
| 85 | Supply & Fixing for in repair 15mm bore stop valves/ Angle valve, cast copper alloy fancy type screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions, complete all as specified and directed by Engineer-in-Charge. |
| 86 | Supply & Fixing in repair 15mm dia CP two way angle valve fixed in pipe, complete all as specified and directed by Engineer-in-Charge. |
| 87 | Supply & Fixing in repair 20mm dia Stop valves / gate valve, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed, complete all as specified and directed by Engineer-in-Charge. |
| 88 | Supply & Fixing in repair Stop valves/Angle valves of size 15mm dia fancy type, chromium plated with long shank and cup (concealed type), screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed, complete all as specified and directed by Engineer-in-Charge. |
| 89 | Supply & Fixing in repair Harrison rails stainless steel (Curtain rod/drapery rod), 20mm dia, powder coated with and including fancy type bracket 2 Nos of each opening and side stopper fancy type powder coated of required shape and size 2 Nos of each opening, complete all as specified and directed by Engineer-in-Charge. |
| 90 | Roughening surfaces of old concrete floor by picking sweeping cleaning & washing down with water to remove dust etc including removal of old treatment of any description and applying one coat of neat cement slurry @ 3.00 Kg/Sqm, complete all as specified and directed by Engineer-in-Charge. |
| 91 | Material & Labour for 40mm thick Cement concrete type B-0, 1:2:4 (12.5mm graded aggregate) as in padding to roof slab and rendering 5mm thick in one layers on concrete surface cement sand mortar 1:3 using water proofing compound as per manufacturer’s instruction finished even fair and smooth without using extra cement, complete all as specified and directed by Engineer-in-Charge.Note:- WPC will be measured and paid separately. |
| 92 | Material & Labour for providing APP based membrane course roof treatment in layers with following provisions:- (i) Applying one coat of bitumen\"s primer polymerized primer oil based coat, evenly @ 0.3 KG/Sqm as priming coat to the prepared surfaces, till the surfaces is properly impregnated and the solvent oil in the base primer shall be allowed to evaporated completely.(ii) Applying APP based pre-fabricated with non-woven polyester reinforced membrane stabilized with fibre glass strands and top with grey mineral slates 3mm thick and weight not less than 3.50 Kg/Sqm by torch application method.(iii)Applying a coat of solar reflective bituminous aluminium paint @ 0.10Kg/Sqm over mineral surface. |
| 93 | Supply only liquid water proofing compound, complete all as specified and directed by Engineer-in-Charge. |
| 94 | Material & Labour for treatment of sunken floor slab comprising of the following specifications with and including demolition of sunken floors complete all as specifiedand directed:-(i) Cleaning the sunken/lowered portion of RCC slab surface (including vertical total depth plus skirting height) of floors by wire brush, chisel out any mortar sticking to the surface and brooming completely.Provision of 40mm thick avg PCC 1:2:4 type B-0 using 12.5mm graded aggregate as in padding concrete to achieve proper slope including cutting holes in bricks or RCC wall for spout.(ii) Rendering of uneven surfaces with 6mm thick Cement Mortar 1:4 mixed with and including integral water proofing compound Sika Plastocreat plus or equivalent make in Fosroc / Thremax as approved by GE @ 0.2% by wt of cement consumed including filling it with water to check dampness and seepage and where dampness / seepage is noticed, nozzles shall be fixed and grouting carried out. (iii)All junctions points of side wall where CI/GI/PVC pipes are passing through shall be sealed with epoxy putty Sika guard 694 F(I) or equivalent make in Fosroc / Thremax as approved by GE.(iv)After drying putty, wash the slab and sides of sunken portion with water and make it clear and clean. |
| 95 | (v) Applying two coats of polymer modified cementious water proof coating with Sika Top seal 107 or equivalent make in Fosroc / Thremax as approved by GE in two coats @ 3kg/sqm to sandwiched with glass fibre reinforcement: Sika Fab-1 or equivalent make in Fosroc / Thremax as approved by GE over base coat as per manufacturer’s instruction to bottom and vertical sides up to finished floor level+100mm height.The thickness of two layers shall be 1mm.When the second layer is still sticky, coarse sand spray shall be carried for the vertical and bottom surface of the sunken portion.(vi) Plaster the bottom and sides up to bottom of the skirting with minimum 20mm thick Cement Mortar 1:4 mixed with integral water proofing compound SIKA plastocreat plus or equivalent make in Fosroc / Thremax as approved by GE @ 0.2% by wt of cement consumed as per manufacturer\"s specification including rounding of corners and in junctions sloping towards spout. (vii)All pipes laid in sunken portion shall be covered with 50mm thick PCC 1:3:6 all round after painting with anticorrosive paint.(viii) The sunken floor shall be filled with lean concrete 1:7:12. Note :- Test the water proofed area (ponding test) by filling water for at least 72 hours and tested for leakage seepage and to the entire satisfaction of GE. Test record for each sunken slab shall be maintained. The treatment shall be carried out by authorised applicators of chemicals. Cost of testing and all Material & Labour is included in the rates quoted above. |
| 96 | Material & Labour for weld-mesh of size 75x75x3mm to be wrapped on the exposed surface of rib of beam & on the slab bottom and tack welding to the exposed reinforcement at close intervals and applying Cement Mortar 1:3 all in complete as per the technical specifications and manufacturer\"s instructions, complete all as specified and directed by Engineer-in-Charge. |
| 97 | Excavating in trenches, not exceeding 1.5 Metre wide and not exceeding 1.5 Metre depth for foundation, etc or not exceeding 10 Sqm on plan and not exceeding 1.5 Metre in depth for shafts, cesspits, manholes, pier holes, etc and getting out in loose/soft soil, complete all as specified and directed by Engineer-in-Charge. |
| 98 | Returning, filling in excavated approved soil, including spreading, levelling, watering and well ramming in layers not exceeding 25cm each, complete all as specified and directed by Engineer-in-Charge. |
| 99 | Removing excavated soil not exceeding 50 Metre and depositing where directed at a level not exceeding 1.5 Metre above the starting point, complete all as specified and directed by Engineer-in-Charge. |
| 100 | Material & Labour for Concrete bed to drain pipes 150mm bore including packing under and hunching against the sides of pipes after they are laid and tested; in cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate, complete all as specified and directed by Engineer-in-Charge. |
| 101 | Material & Labour for reinforced concrete pipes, class NP-2, laid and jointed complete with collars, laid in trenches and jointed, complete all as specified and directed by Engineer-in-Charge. |
| 102 | Material & Labour for Cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate in foundations, filling and mass concrete including sub base of floors, complete all as specified and directed by Engineer-in-Charge. |
| 103 | Material & Labour for Cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate in surface channels and drains, complete all as specified and directed by Engineer-in-Charge. |
| 104 | Material & Labour for Providing cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate in cills, bed blocks, copings, bed plates, bond stones, etc including weathering, slightly rounded or chamfered angles and throating as directed including necessary form work, complete all as specified and directed by Engineer-in-Charge. |
| 105 | Supply & Fixing Joist, channel, angle, or tee sections, Fe-410-W (Gde- E-250) quality-B fixed independently, without connecting plates, etc., complete all as specified and directed by Engineer-in-Charge. |
| 106 | Material & Labour for preparing new surface of steel of any desc over 10 cm width or girth and applying two coat of synthetic enamel paint over red oxide, complete all as specified and directed by Engineer-in-Charge. |
| 107 | Material & Labour for PCC 1:2:4 type B-1 using 20mm graded stone aggregate as in filling inChowkhat, hold fast block etc., complete all as specified and directed by Engineer-in-Charge. |
| 108 | Chipping of loose/ damaged /cracked / previously repaired / delaminated or weak concrete by chieseling to expose the sound core concrete where ever required and to expose rusted reinforcement upto depth n. exc. 50mm and disposal of rubbish off the premises to a distance not exc. 50 mtrs including cleaning of reinforced concrete surface by air compressor, complete all as specified and directed by Engineer-in-Charge. |
| 109 | Supply and apply of rust remover cum passivator to remove rust from existing reinforcement by using product: Rustoff-100 of Sika or equivalent make in Fosroc/ Thermax as approved by GE, with density 1.01 Kg/ltr at 30 degree celsius and consumption : 0.2 Kg/Sqm/coat, complete all as specified and directed by Engineer-in-Charge.Note: The mtrl to be applied thoroughly on exposed rebars only with the help of a brush of suitable size. The area will be measured as length of bar x two times the dia of bar). |
| 110 | Supply and apply a cement based polymer modified rebar corrosion protection system to existing reinforcement using cement based polymer modified rebar corrosion protection system with consumption : 3.75 kg/Sqm for two coats and Product requirements: carbonation resistance: 2mm of Sika Top Armatec®-108 of Sika or equivalent make in Fosroc / Thermax as approved by GE corresponds to 20 mm of normal mortar; bond strength > 1N / Sqmm according to ASTM C 882-78, complete all as specified and directed by Engineer-in-Charge.Note: The mtrl to be applied thoroughly on exposed rebars only with the help of a brush of suitable size. The area will be measured as length of bar x two times the dia of bar) |
| 111 | Material & Labour for Providing, mixing & applying two component Epoxy resin concrete Bonding coat on prepared RCC surfaces as per manufacturer\"s specification including preparation of surface thoroughly and cleaning complete where ever required with using Product: Sikadur ®-32 LP of Sika or equivalent in Fosroc / Thermax as approved by GE with Consumption: 0.4 kg/Sqm and Product requirements: Complies with ASTMC 881-78, Type II Grade 2 Class B+C, complete all as specified and directed by Engineer-in-Charge. |
| 112 | Material & Labour for providing by mixing and trowel application of pre-packed, light weight, two component structural grade polymer modified fibre reinforced thixotropic cement mortar Sika Mono top 122F of Sika or equivalent make in Fosroc / Thermax as approved by GE at an average thickness exceeding 10mm and upto 25mm to the prepared concrete surface in soffit of slabs, beam, columns, parapets, fins and facias at any height, including finishing of applied Polymer mortar as per the technical specifications and manufacturer\"s instructions, complete all as specified and directed by Engineer-in-Charge. |
| 113 | Supply and apply a ready to use non shrink, cementitious free flow micro-concrete (<100mm) using Product: SikaRep ® Microcrete-4+ adequate coarse aggregate, Yield: approx 17 Ltr/bag (30 Kg) (depending on the size and quantity of coarse aggregate added), Product : Sika Rep ® Microcrete-4orequivalent make in Fosroc / Thermax as approved by GE, Product requirements: compressive strength > 60 N/Sqmm (28 days) according to ASTM C 1107-99, complete all as specified and directed by Engineer-in-Charge.Note: 1 Providing and erecting hydraulic & manual steel props upto full height, braced at centre, resting on wedge and block to support the structure provisionally during repair work. This is not paid separately.Note: 2 Providing and fixing water tight centering and shuttering including bolting, strutting, propping etc. including removal of form work from column, beam etc. complete as per site requirement. This is not paid separately. |
| 114 | Material & Labour for CRS TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire annealed not less than 0.9mm dia or securing with clips, complete all as specified and directed by Engineer-in-Charge. |
| 115 | -ditto- all as per item No. above, but 6mm to 8mm dia., complete all as specified and directed by Engineer-in-Charge. |
| 116 | -ditto- all as per item No. above, but 5mm dia and over upto 10mm dia as in stirrups, spacers and binders, complete all as specified and directed by Engineer-in-Charge. |
| 117 | Supply & Fixing in repair Steel rolling shutters, without ball bearing, as specified including top cover as per IS: 6248-1979, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated,push pull or manual type, complete all as specified and directed by Engineer-in-Charge. |
| 118 | Supply & Fixing Ball bearing for rolling shutters as per IS: 6248-1979, complete all as specified and directed by Engineer-in-Charge. |
| 119 | Supply & Fixing in repair Grating doom 100mm dia of PTMT (Minimum weight 25gms), complete all as specified and directed by Engineer-in-Charge. |
| 120 | Supply and fixing 12mm thick toughened glass as in hinged doors, partitions/ automatic doors and similar work including cutting to shape, drilling holes required with all stainless steel fitting including L connector, silicon fixer, decorative handle, lock floor door spring for weight not exceeding 80 Kg for each leaf and decorative lamination film etc., with all fittings, complete all as specified and directed by Engineer-in-charge. |
| 121 | Providing and fixing factory made uPVC white colour Sliding window Two track made of extruded profiles with wall thickness of 2.3mm (+- 0.2mm). Window profile with hollow section with multi chamber, Frame (60mm x 62mm). Sash (42mm x 67mm). Sliding Interlock (One vertical length in each shutter) (45.5mm x 28mm). Glazing bead (24.5mmx 16mm) will he metered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket 1.2 + -0.2mm thick galvanized steel frame (30mm x 21.5mm), Sash (30mm x 18mm), profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners. Hardware : [Touch Lock of zinc alloyed (white powder coated), steel roller system including 5mm thick glazing with selected quality glass, aluminium track on bottom rail for two track sliding frame, wool pine for Sliding sash and interlock.], complete all as specified and directed by Engineer-in-charge. Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net opening will be measured for payment purpose) |
| 122 | Supply & Fixing 4.8mm thick Ordinary Quality, glazing with/ without oil putty in squares exceeding 0.5 Sqm in each pane in metal or aluminium window, complete all as specified and directed by Engineer-in-charge. |
| 123 | Taking down wooden door shutters not exceeding 1.0 Sqm, easing and adjusting and also re-fixing builder’s hardware as required etc., and re-fixing door shutters in same opening, complete all as specified and directed by Engineer-in-charge. |
| 124 | Material & Labour for preparation of old painted wood or wood based surfaces of any description exceeding 10cm width or girth and applying one coat of synthetic enamel paint etc., complete all as specified and directed by Engineer-in-charge. |
| 125 | E/M Part |
| 126 | Taking down carefully copper /aluminium point wiring (light, fan, socket or power point) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, socket, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per condition separately) and making good distribution surfaces of walls, floors, etc., complete all as specified and directed by Engr-in-charge. |
| 127 | Taking down unserviceable sub main wiring of any size and including PVC conduit and accessories & removing from site, complete all as specified and directed by Engr-in-charge. |
| 128 | Taking down electric connections and taking down old unserviceable MCB SPN/SP/TPN/MS, Meter Box, DB\"s etc., of any capacity, complete all as specified and directed by Engr-in-charge. |
| 129 | Taking down Ceiling fan, sealing cable end, dismantling blades and removing fan and blades and deposit to E/M store, complete all as specified and directed by Engr-in-charge. |
| 130 | Material & Labour for Point wiring complete with 1.5 sqmm single core PVC insulated but unsheathed multi-stranded copper conductor FRLS cable 650/1100 Volts grade drawn through and including non-metallic rigid PVC heavy dutyconcealed conduit (minimum 20 mm dia external) but shall be increased as per actual site requirement in accordance with clause 19.125 of SSR part- I ISI marked with wall thickness not less than 1.8 mm including conduit accessories like bends, tees, junction boxes etc fixed concealed/ recessed in wall or ceiling etc including 1.5 sqmm PVC insulated but unsheathed multi-stranded copper conductor FRLS cable as earth continuity wire including modular type metal flush box with cover plate and frame of required modules for mounting of modular switches, sockets, switch sockets, fan regulators with required modules, complete all as specified and directed by Engr-in-charge.for the following:- |
| 131 | One light point controlled by one, one way switch |
| 132 | One fan/Exhaust point controlled by one, one way switch |
| 133 | One light point controlled by two 2-way switches, with cables 1.5 sqmm size |
| 134 | One 3 pin 6 Amps socket outlet on same board |
| 135 | One 3 pin 6 Amps socket outlet on independent board . |
| 136 | Material & Labour for Point wiring complete with 2.5 Sqmm single core PVC insulated but unsheathed multi-strand copper conductor FRLS cable 650/1100 Volts grade conforming to IS-694 drawn through PVC conduit (minimum 20mm dia (external) but shall be increased as per actual site requirement in accordance with clause 19.125 of SSR Part I) ISI marked with wall thickness not less than 1.8mm heavy duty including conduit accessories concealed pressed steel terminal boxes of size cover white/coloured including 2.5 Sqmm PVC insulated but unsheathed copper conductor FRLS cable as earth continuity wire for one 3 pin 15 or 16 Amps socket outlet on independent board, including modular type metal flush box with cover plate and frame of required module for mounting of modular switches, sockets, switch sockets with required modules, complete all as specified and directed by Engr-in-charge. |
| 137 | Material & Labour for Point wiring complete with 4 Sqmm single core PVC insulated but unsheathed multi-strand copper conductor FRLS cable 650/1100 Volts grade conforming to IS-694 drawn through PVC conduit (minimum 20mm dia (external) but shall be increased as per actual site requirement in accordance with clause 19.125 of SSR Part I) ISI marked with wall thickness not less than 1.8mm heavy duty including conduit accessories concealed pressed steel terminal boxes of size cover white/coloured including4 Sqmm PVC insulated but unsheathed copper conductor FRLS cable as earth continuity wire for one 3 pin 15 or 16 Amps socket outlet on independent board, for AC Point including modular type metal flush box with cover plate and frame of required module for mounting of modular switches, sockets, switch sockets with required modules, complete all as specified and directed by Engr-in-charge. |
| 138 | Supply & Fixing modular switch 1 way, 6 Amps, 1 module (ISI marked), complete all as specified and directed by Engr-in-charge. |
| 139 | Supply & Fixing modular switch 1 way, 16 Amps, 1 module (ISI marked), complete all as specified and directed by Engr-in-charge. |
| 140 | Supply & Fixing modular socket, 6 Amps, 2/3 pin combined 2 module (ISI marked), complete all as specified and directed by Engr-in-charge. |
| 141 | Supply & Fixing modular socket, 6/16 Amps, 2/3 pin combined 2 module (ISI marked), complete all as specified and directed by Engr-in-charge. |
| 142 | Supply & Fixing modular switch 2 way, 6 Amps, 1 module (ISI marked), complete all as specified and directed by Engr-in-charge. |
| 143 | Supply & Fixing modular fan regulator, 120 watt, 2 module (ISI marked), complete all as specified and directed by Engr-in-charge. |
| 144 | Supply & Fixing ceiling rose, surface Bakelite, 65 x 17 mm three terminals (ISI Marked), complete all as specified and directed by Engr-in-charge. |
| 145 | Supply & Fixing in of wall mounted LED Tube light fitting 1 x 20W LED (6500K), 4 feet, Sleek and seamless profiled extruded aluminium batten with an efficient diffuser to illuminate work, including making connections with 2 core flexible copper wire 0.50 Sqmm from ceiling rose after fixing fitting, complete all as specified and directed by Engr-in-charge. Make Philips - Cat Part No- BN100C LED40S-6500 PSU L120 GR or equivalent to Wipro/GE lighting |
| 146 | Supply & Fixing in of wall mounted LED Tube light fitting 1 x 10W LED (6500K), 2 feet, Sleek and seamless profiled extruded aluminium batten with an efficient diffuser to illuminate work, including making connections with 2 core flexible copper wire 0.50 Sqmm from ceiling rose after fixing fitting, complete all as specified and directed by Engr-in-charge. Make Philips -Cat Part No BN 021 LED12S 6500 PSU GR or equivalent to Wipro/GE Lighting |
| 147 | Supply & Fixing LED 25 Watts (5700K) Bldg Security light fitting, and including with GI Pipe 32 mm dia bracket with connected with 2 core flexible copper wire 0.50 Sqmm from ceiling rose after fixing fitting in position at site, complete all as specified and directed by Engr-in-charge. Make: Wipro Cat No LR02-291-XXX-57-XX /Philips / Havells /CG |
| 148 | Taking up and down of existing ceiling fan after that dismantling of fan motor, cutting of burnt winding of rotor and rewinding with same gauge copper wire winding with insulated material, replacement of 2.5mfd capacitor and reassembling. Including painting of fan and blades, complete all as specified and directed by Engr-in-charge. |
| 149 | Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers, complete all as specified and directed by Engr-in-charge. Note : Cutting of wall of appropriate size of fan and making good in cement 1:3 or cement concrete 1:2:4 type B-1 as depth of cut required and finishing properly to match the surfaces to fix the Exhaust fan is inclusive job in each of item. |
| 150 | Supply and fix electric water heater, storage type with inner tank and heating element upto 2 KW capacity 25 litre, BEE 3 star and above rated complete with all accessories such as safety valve, thermostat, NRV, with Anchor fasteners of suitable size and including Flexible hot/cold connection Pipe -02 Nos, complete all as specified and directed by Engr-in-charge. |
| 151 | Material & Labour for sub main wiring with two single core 4 x 6 Sqmm PVC (FRLS) insulated multi-stranded flexible copper conductor cable 660/1100 volts grade down in through including Concealed PVC Conduit with all accessories, PVC insulated 2 x 4 Sqmm single core single strand copper conductor as continuous earth wire in green colour connected to common earth dolly, complete all as specified and directed by Engr-in-charge. Note : 1.Two runs ofcable, one run of earth wire, one run of PVC conduit will be measured and paid one unit. |
| 152 | Material & Labour for sub main wiring with two single core 2 x 4 Sqmm PVC (FRLS) insulated multi-strandedflexible copperconductorcable 660/1100 volts grade downin through including Concealed PVC Conduit with all accessories, PVC insulated 1 x 2.5 Sqmmsinglecore singlestrand copperconductoras continuous earth wire in greencolour connected to commonearth dolly all as specified and as directed. Note : 1.Two runs ofcable, one run of earth wire, one run of PVC conduit will be measured and paid one unit. |
| 153 | Supply and fixing Sheet metal enclosure (factory made) double door for distribution board (when MCB\"s are to be used) Triple pole neutral 415 V, 4 ways with 200 Amp rated bus bar connection with suitable size of thimbles, complete all as specified and directed by Engr-in-charge. |
| 154 | Supply and fixing Sheet metal enclosure (factory made) double door for distribution board (when MCB\"s are to be used) Single pole neutral 240 V, 16 ways with 200 Amp rated bus bar connection with suitable size of thimbles, complete all as specified and directed by Engr-in-charge. |
| 155 | Supply and fixing Sheet metal enclosure (factory made) double door for distribution board (when MCB\"s are to be used) Single pole neutral 240 V, 8 ways with 200 Amp rated bus bar connection with suitable size of thimbles, complete all as specified and directed by Engr-in-charge. |
| 156 | Supply and fixing amp rating 240V, 10KA \"C\" curve miniature circuit breaker (MCB) TPN 40 to 100Amp current carrying capacity in the MCB DB complete with connection testing and commissioning, complete all as specified and directed by Engr-in-charge. |
| 157 | Supply and fixing amp rating 240V, 10KA \"C\" curve miniature circuit breaker (MCB) SPN 32Amp current carrying capacity in the MCB DB complete with connection testing and commissioning, complete all as specified and directed by Engr-in-charge. |
| 158 | Supply and fixing 240V, 10 KA \"B\" curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 AMP, in the MCB DB Complete with connection testing and commissioning, complete all as specified and directed by Engr-in-charge. |
| 159 | Supply & Fixing Modular Motor starter 16A capacity, 02 Module with metal flush box, cover plate of required module for ACs, complete all as specified and directed by Engr-in-charge. Make Legrand Cat No 6811 66 C&S / Anchor or equivalent all as specified and as directed |
| 160 | Material & Labour for Earthing for poles and other machinery/eqpt using GI strip as earth lead and MS galvanized steel earth plate electrode 60cmx60cmx 6 mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below ground level) with top edge of the plate is not less than 1.5 mtr below normal ground level connected to galvanized iron strips 32x6mm as Earthing lead with GI pipe, nuts, bolts and washers complete upto and including test point made out of 40x3mm GI flat, PCC pit of required size in PCC 1:2:4 type B1 and RCC cover with frame, charcoal, common salt15cm at round the earth plate watering pipe 20mm med grade/galvanized and 40mm dia GI pipe light grade for GI strip protected steel with funnel complete all as specified and directed as shown in electrical plate No 3 of SSR Part-I 2009. |
| 161 | Supply and laying of XLPEinsulated and PVC armoured heavy duty 1100 volt grade electric LT UG cable with aluminium conductor of size 50 Sqmm 3.5 Core laid in trenches/along the wall/pole including making good the disturbed surfaces of walls/floor etc., all connections, Complete all as specified & directed by Engineer-in-Charge. |
| 162 | Supply and laying 50 /38mm Double Walled Corrugated (DWC) Pipes having corrugation on the outer wall and plain surface on the inner wall confirming to IS14930 (Part-II) for protection of UG cables, laid in trenches/ road/ drain or fixed along wall, poles or laid under floor, Complete all as specified & directed by Engineer-in-Charge.Make : Rex / Poly/ Gemini |
| 163 | Material & Labour for cutting existing road/hard standing not exc 45 x 45 cm in wide & depth getting out excavated material for laying cable/GI tube, returning filling & well ramming watering finish surface 10 cm from top using PCC 1:3:6; including removal of surpluses soil, Complete all as specified & directed by Engineer-in-Charge. |
| 164 | Cutting the 50mm bore CI/DI pipes and reducing the required length before laying for inserting of new CI specials such as Tees /Reducers /Tail pieces /collers /sluice valve/Air release valve etc., Complete all as specified & directed by Engineer-in-Charge. |
| 165 | Supplying and laying of CPVC pipes of 40mm dia SDR 11 & Plain CPVC SDR 11 fittings in trenches & fitting on walls, ceiling or floors, Complete all as specified & directed by Engineer-in-Charge. |
| 166 | Supplying and laying of CPVC pipes of 25mm dia SDR 11 & Plain CPVC SDR 11 fittings in trenches & fitting on walls, ceiling or floors, Complete all as specified & directed by Engineer-in-Charge. |
| 167 | Supply & fixing CPVC ball valve, Complete all as specified & directed by Engineer-in-Charge. of following size:- |
| 168 | 40mm dia |
| 169 | 25mm dia |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2025 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
