Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Taking down cement plaster including racking out joints, hacking for key & scrubbing down with water etc complete all as specified and directed by Engineer - in -Charge. |
| 2 | Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed |
| 3 | Dismantling of stone slabs and tiles of any description or thickness in floors, aprons Laid, bedded and pointed in any etc. |
| 4 | Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove. |
| 5 | Demolition of cement concrete (un-reinforced) in ground floors and pavings not exceeding 15 cm thickness below or above ground level complete all as specified and directed by Engineer-in-Charge. |
| 6 | Demolition of brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar facing dressed stone work and precast concrete articles complete all as specified and directed by Engineer-in-Charge. |
| 7 | Demolition ofconcrete of any description and in any position not otherwise specifically provided for complete all as specified and directed |
| 8 | Taking down chowkats or frames not exceeding 1.5 Sqm each with shutter (without taking off shutter from the frame) complete all as specified and directed by Engineer-in-Charge. |
| 9 | Taking down chowkats or frames exceeding 1.5 Sqm but not exceeding 4 Sqm each with shutter (without taking off shutter from the frame) complete all as specified and directed by Engineer-in-Charge. |
| 10 | Taking down shutter of any description exc. 1 sqm but n.exc 2 sqm each and removing from site complete all as specified and directed by Engineer-in-Charge. |
| 11 | Taking down shutter and refixing with easing in same openingof any description exc. 1 sqm but n.exc 2 sqm each |
| 12 | Dismantling of 100mm bore cast iron/ pvcdrain pipe alongwith fittings and accessoriesjointed in cement mortar and taking out from walls, floors or fromtrenches, if required complete all as specified and directed. |
| 13 | Dismantling of 75mm bore cast iron / pvc drain pipe alongwith fittings and accessoriesjointed in cement mortar and taking out from walls, floors or from trenches, if required complete all as specified and directed . |
| 14 | Taking up or down15 mm steel tubingand connections including cleaning for refixing or removal complete all as specified and directed by Engr-in-Charge |
| 15 | Taking up or down 20 mm steel tubingand connections including cleaning for refixing or removal complete all as specified and directed by Engr-in-Charge |
| 16 | Dismantling water tanks500 & n exc 1000 and removing to store of all retrieved material complete all as specified and directed. |
| 17 | M&L 15mm thick rendering in cement mortar 1:4 to brickmasonry wall surfaces or on other than fair faces of brick wall surfaces finished fair & even without using extra cement for fixing tiles etc complete all as specified and directed |
| 18 | M & L 25 mm thick PCC 1:2:4type B0, using 12.5mm graded aggregate as in floors toreceive surface of tile complete all as specified and directed. |
| 19 | M&L screed bed or bedding layer of mortar, 15 mm thick, in cement mortar 1:6, for laying floor finishes/tiles complete all as specified and directed. |
| 20 | M&L screed bed or bedding layer of mortar, 20 mm thick, in cement mortar 1:6, for laying floor finishes/tiles complete all as specified and directed. |
| 21 | M&L Non- skid coloured ceramic tiles 7 to 8mm thick (square / rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile complete all as specified and directed. |
| 22 | M&L for non skid ceramictiles 7 to 8 mm thick (square / rectangular )area of each tiles exc 0.18 sqm but not exceeding 0.38 Sqm in floor etc set and jointed in neat cement slurry and pointed in coloured cement to match with colouredtiles complete all as specified and directed. |
| 23 | M&L for non skid ceramictiles 7 to 8 mm thick (square / rectangular )area of each tiles exc 0.18 sqm but not exceeding 0.38 Sqm on vertical surfacesetc set and jointed in neat cement slurry and pointed in coloured cement to match with colouredtiles complete all as specified and directed. |
| 24 | M & L 7 to 8 mm thick glazed coloured ceramic tiles ( square/ rectangular) with border , area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, as in vertical surfaces such as skirting or dado set & jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles complete all as specified and directed. |
| 25 | M&L 20 mm thick Granite of black colour(tablee rubbed and polished) as in windows cill &cooking platforms and like in 15mm cement mortar (1:4) screed bed including form work , pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite with full round bull nosing edging complete all as spd as directed |
| 26 | M & L for 75mm thick PCC 1:3:6 , type C-2 using 40 mm graded stone aggregate as in plinth protection laid in slope in 1:30 in alternative bays not exceeding 3 mtr in length.Exposed surfaces finished even and smooth without using extra cement including raking out joints between panel to panel and panel to wall and plugging the same with bitumen mastic using bitumen and sand mixture in 1:3 complete all as specified and directed . |
| 27 | M& L 75 mm thick PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in sub base floor / pavings complete all as specified and directed |
| 28 | M&LSand filling under floors or in foundationincluding watering and consolidation complete all as spd |
| 29 | M&L for cement Concrete coloured interlocking paver blocks shall be factory made with casting in rubber/pvc moulds & compacting on a vibro table assembly and shall be cured in curing tank for atleast 14 days and then air dried before use. The paver block shall be confirming to IS 15658 -2006 of60mm thickness, M-35 Grade. Approved design, shape, size and colour of top layer complete all as specified and directed. |
| 30 | Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete. |
| 31 | M&L forreinforced cement concrete M-25 (20 mm graded aggregates) (nominal mix)(nominal mix) as in slabs supported on wall like including bonding agent , complete all as specified (reinforcement to be measured & paid under respective items). (nominal mix) as in slabs supported on wall,landing, balconies, shelves and like including bonding agent , complete all as specified (reinforcement to be measured & paid under respective items). |
| 32 | M&L form work to chajja, weather shade, troughs and similar items includingedges for rough finished surfaces of concrete flat, complete all as specified. |
| 33 | M&L form work to edges of concrete flats, treads, breaks in floors window cill, concrete railing opening in conc wall , floor and roof n.exc 20cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10 cm but n.exc 20cm wide for rough finished surfaces of concrete, complete all as specified. |
| 34 | Supply and fix TMT bars, 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) but not less than 0.9 mm dia conforming to Fe-410 - 0, complete all as specified. |
| 35 | M &L for PCC (1:2:4) type B-0 using 12.5 mm graded stone aggregrate laid over roof, kerbs or mud stops, rounded or chamferedfinished even and smooth without using extra cement complete all as spd and directed. |
| 36 | supply Integral water proofing Liquid |
| 37 | M&L for brick work with fly ash bricks, straight or curved on plan exc. 6 m mean radius, built in CM (1:6) complete all as spd as directed |
| 38 | M&L rendering 15 mm thick in CM 1:6 on brick masonary wall surfaces or on other than fair faces of brick masonry finished even and smooth witout using extra cement complete all as specified and directed. |
| 39 | M& L for rendering 10mm thick in cement mortar (1:4), and 5 mm thick setting layer in CM1:3 finished even and smooth using extra cementto on brick masonary wall surfaces or on other than fair faces of brick masonaryfinishedeven and smooth without using extra cement with using water proofing liquid @ 150 ml per bag of cement complete all as specified and directed.(Note : Water proofing liquid shall be measured and paid separately) |
| 40 | Dismantling timber scantlings 40 Sqcm and over in section, in any position , framed work complete all as specified and directed. |
| 41 | Dismantling asbestos cement (corrugated, semi corrugated etc) sheets in roofcoveringscomplete all as specified and directed. |
| 42 | Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc.) insulation boards / slabs / blankets of any thickness, including cover fillets complete all as specified and directed. |
| 43 | M&L for Roof trusses (framed), trussed purlins crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle channel or flat sections) including distance pieces, cleats etc GDE Fe 410-S. complete all as specified and directed. |
| 44 | M&L for E-board false ceiling consisting of powder coated GI wall angle, main T and cross Tof 25mmX 25 mm X 1.40 mm thick grid frame work, joist, angle/ Tee as directed and mild steel wire hook not less than 6 mm dia with arrangement for adjusting height of ceiling and including provn of 4 mm thick E-Classic board in pannelof size 600X600mm with necessary off cut including dismantling of existing false ceiling and taking down and refixing of Electric fitting carefully complete all as specified and directed. |
| 45 | S&F for Pressed steel frames Size 125mm x 60 mm for doors with one or more rebatesincluding necessary fixing lugs, hinges, lock strike plate etc., complete all as specified and directed |
| 46 | S&F Flush shutters, 30 mm thickness solid core construction, with block board core and plywood face panels, commercial type on both sidesFace is covered with decorative face veneer with lipping/frame to match complete all as specified and directed by Engineer-in-Charge. |
| 47 | S&F 35mm thick factory made glazed and skeleton door shutters open rebated of second class hard wood rail and styles(Hollock), prepared to receive glass/gauge etc without sash bars, edges of framing plain cham-fered or rounded, mitred and rebated sash bars, any numbers The size of rails & style as specified in SSR Part-I (2009) section 8 and as per IS-1003(Part-I) kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401 complete all as specified and directed by Engineer-in-Charge.(Note :- S & F Glass/gauge shall be measured and paid for separately) |
| 48 | S & F 150 mm long floor door stopper of aluminium alloy body and tongue, brass body and tongue with hard drawn steel spring. Fixed in floor complete all as specified and directed. |
| 49 | S&F for 18 mm thick termite resistant and water proof, both side prelaminated wooden plywood one side with decorative choice lamination, and other side plain white lamination total thickness not more than 22 mm thick, as in cup board shutters, with wardrobe/ finch lock & PVC lipping on all exposed edges of same texture and shade, withcomplete all as specified as directed. Note:1) Design & layout of wardrobe and pattern / colour of lamination to be approved by GE. 2) thickness of laminated not less than 1mm for inside plain white type & 1.5 mm for outer decorative type. The laminate shall be fixed to base with approved adhesive as per manufacturer\"s instructions and machine pressed to ensure proper bonding with base ply and avoid air pockets. 3) Frame to be fixed to walls, soffits & base of cupboard with fasterners. |
| 50 | S & F for aluminium powder coated frame hollow sections members of size 63.50 mm x38mmx 1.48mm thick,4 mm thick aluminium composite panel LDPE core with PET coating fixed with into the wall for kithen cabinet/ cupboard shelf incl hanging self for clothes with aluminium clip/strips, pvc beadings fixed with adhesive on edging , design as per site requirements basis, complete all neccessary fittingall as specified and directed |
| 51 | S & F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm thick single side prelam PVC sheet used instead of Plain colour PVC sheet , suppling & fixing in opening as per specification & drawing |
| 52 | S&F 30 mm thick factory made both side Prelam PVC sheet used instead of Plain colour PVC sheet. Stile and rails feathered at edges consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded palin colour PVC `C\" channel heaving aPanelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing. |
| 53 | S&F mild steel window grills box typeframed work as in window guard bars, grills or forged into spikes, framed balusters, walkway railing and similar work including welding complete FE-290 grade E-165 all as specified and directed. |
| 54 | S&F Powder coated aluminium ventilators box type with louvers & wire mesh fixed with neoprene rubber gasket, aluminium beading, clips. Frame made with powder coated aluminium section of size as appended below (i)frame :45.2mm x35mm X 1.15 mm(ii) Aluminium beading - 0.7mm thick(iii) Glass louvers depth 6 inch. Blade Angle: 38 degrees and thickness of blade 2.02 mm with 106.25 mm spacing.(iv) Aluminium neccessary fittings complete as required.(v) Making good of wall surfaces with silicon to match with existing surfaces complete all as specified and directed. |
| 55 | S&F Powder coated aluminium sliding windows and frame with movable shutter ( sliding on minimum two PVC roller of best quality on two tracks Aluminium composite panel shutter fixed with neoprene rubber gasket with aluminium beading, clips,frame made with aluminium section as appended below-(i) Window frame :68.4x38mm X 1.15 mm thick for two tracks.(ii) Top/bottom rail and style / rail of shutter : 15x37.5x1.15 mm thick and over.(iii) Aluminium beading - 0.7mm thick(v)Aluminiumfittings suchaluminium suitable handle with auto interlock cap with suitable size .(vi) Making good of wall surfaces with silicon to match with existing surfaces complete all as specified and directed. |
| 56 | S&F magnet catch with striking plate including letting in and fixed, complete all as specified. |
| 57 | S & F 300 mm long Aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed |
| 58 | S & F 150 mm thick Aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed |
| 59 | S&F 150mm size aluminium handles, cast type anodised completed all as specified and directed. |
| 60 | S&F 100 mm size butt hinges medium weight stainless steel colled rolledcomplete all as specified and directed by Engineer-in-Charge. |
| 61 | S&F 300mm size ordinary mild steel , rat tailed rod pattern spring including roller and roller platewelded to mild steel frame.fixed in repair complete all as spd & directed. |
| 62 | S&F 300 mm long aluminiumsliding door bolts plate type with bright bolt not less than 16 mm dia with and including a minimum of 6 bolts and nuts, 04 Nos on bolt plate and 02 Nos on staple plate and fix complete all as specified and directed |
| 63 | S & F hydraulic concealed hinge with clip on installation and integrated Silent System, opening angle not less than 100º, For shutter thickness 15 - 24 mm full overlay type shutters, hinge cup dia 35 mm including necessary fixing arrangement with SS screw complete all as specified & directed. |
| 64 | S&F stainless steel wire cloth, 0.56 mm nominal dia of wire and average with of aperture 1.18 mm and fixed with stainless steel wire staples complete all as specified and directed by Engineer-in-Charge. |
| 65 | S&F 1000 litres, rotational moulded polyethylene of white colour in tripple layer water storage tank (cylindrical vertical with closed top with suitable size ofM S Tasla with suitable locking system ), hoisted and fixed in position complete all as specified and directed |
| 66 | S&F 20mm bore ball brass valve high pressure with polythene float and fly nut complete, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed by Engineer-in-Charge. |
| 67 | S&F 15 mm dia steel water tubing galvanized medium grade concealed in all type wallwith all fittings, fixed to walls and ceiling or in floor complete all as specified and directed by Engineer-in-Charge |
| 68 | S&F 20 mm dia steel water tubing, galvanized, medium gradeconcealed in all type wallwith all fittings,fixed to walls and ceiling or in floor complete all as specified and directed |
| 69 | S&F in repairs Brass chromium platedwall mixer 2 in 1 , 15mm for mixing hot & cold water screwd down three joints to steel pipes or unions and plugging and screwed to walls complete all as specified and directed |
| 70 | S&F in repair fancy type 15mm dia chromium plated fancy type wall mixer hot & cold with long swan for kitchen sink fixing and connection to pipes complete all as directed. |
| 71 | S & F in repair fancy type 150mm size square brass CP shower rose all as specified. |
| 72 | S&F in repairs 15 mm dia bib tap fancy type chromium plated with flange quarter turncomplete all as specified as directed. |
| 73 | S&F in repairs 15 mm dia bib tapcast copper alloy with butterfly handle , screwed down for iron pipe or for brass ferrule and fixed complete all as specified as directed. |
| 74 | S&F in repairs vitreous chinaware coloured wash hand basin with pedestal. complete including fancy CP pillar tap, CP Waste coupling ,waste pipe ,complete fixing arrangementand cutting for and pinningin walls & making good complete all as specifed and directed by Eng in charge. |
| 75 | S&F stainless steel of AE - SI 316 grade tubulartowel ringincluding apair ofCP brass bracket complete all as specified. |
| 76 | S&F in repairs 15mm bore PVC connections, with PTMT nuts of length 450mm complete all as specified and directed. |
| 77 | S&F in repair fancy type brass chromium plated soap dish of 160x160x90 mm , complete all as specified. |
| 78 | S&F in repair fancy type chromium plated brass angle valve type suitable for 15mm bore pipe complete all as specified. |
| 79 | S&Fin repair fancy type stainless steeltowel racksize 600mmincluding apair of brass bracket complete all as specified &directed by Engr in charge. |
| 80 | S&F chromium plated brass tubular towel rail 20 mm dia, D type for wash hand basin centre holed fixed to iron pipe complete all as specified and directed. |
| 81 | S & F in repair fancy type sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12 cm wide with CP bracket gaurd and railling 60 cm long complete all as specified. |
| 82 | S&F in repair fancy type glass corner 300mm radius of 10mm thick toughned glass with CP railing fixed with screws fancy type complete all as specified . |
| 83 | S&F in repairs of 20mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed |
| 84 | S&F in repair 15 mm dia fancy type stop cock , chromium plated with long shank and cup (conncelaed type)for iron pipe or for unions and fixed complete all as specified and directed. |
| 85 | S&F in repair vitreous china squatting pan of orrissa pattern long pan size580 x 440 mm white with \"P\"or \"S\" trap size100 mm dia front or back inlet and integral foot rest any pattern (excluding flushing cistern and flush pipe) including provn of lime concrete bedding complete all as specified. |
| 86 | S&F in repairs, PVC low level flushing cistern 10 litres capacity, valve less, symphonic action type with float, handle including 32mm dia PVC flush pipe of polyethylene of low or high density & bracket etc complete all as specified and directed |
| 87 | S&F in repairPVC (SWR) multifloor trap with grating including jointing with solvent cement floor trap 75 mm dia outlet plain with grating including jointing to waste pipe fixed in cement concrete 1:2:4, typeB-1 complete all as specified and directed. |
| 88 | S&F in repair PVC (SWR) 75 mm bore pipes single socketed in any length with rubber ring joints fixed to wall and floorwith necessary fitting complete all as specified and directed by Engr-in-charge. |
| 89 | S&F in repair PVC (SWR) 110mm bore pipes single socketed in any length with rubber ring joints fixed to wall and floorwith necessary fittingcomplete all as specified and directed. |
| 90 | S&F PVC (SWR) 110mm bore bends anyradiuscomplete all as specified and directed. |
| 91 | S&F PVC (SWR) 75mm bore bends any radiuscomplete all as specified and directed. |
| 92 | S&F designed looking mirror size exc 0.54 sqm to 0.75 sqm of selected quality 6mm thick glass, mounted on fixed to wall with CPplugs with chromium plated brass screws and cup washers, complete all as specified |
| 93 | S&F in repairs Stainless Steel plate rack of size 90x80x25cm made with 1.00 mm thick sheet including taking out existing wooden plate rack, complete all as specified. |
| 94 | S & F for 0.8 mm thick stainless steel kitchen sink size 590x460x230mmundermount, single bowl (bowl size 540x410x230 mm) , incl waste pipe & SS coupling, complete all as specified and directed |
| 95 | S&F in repair20 mm dia stainless steel 1.0 mm thick fancy typedroppery rod with decorative design matching brackets as approved and knobs (lattu) or end bracket as required incl fitting with 80 mm long SS screw with 75 mm long wooden gitty of appropriate c/s in each end & intermediate support complete all as specified and as directed |
| 96 | S&F Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding door,Fixed with angle cleats or other connecting plates |
| 97 | S&F Pre-coated galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 mpa as in roof covering / cladding to wall, fixed with self tapping screws as specified. |
| 98 | S&F Pre-coated galvalume aluminium zinc coating GI based Plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 mpa as in roof covering / cladding to wall, fixed with self tapping screws as specified. |
| 99 | M & L for cutting chases of hanging chajjas, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges ofsunshades, shelves, lintels, Chajja ( up to IInd floor) etc making good, cutting out exc 10cm and not exc 40cm girth in RCC chajjas in brick walls complete all as specified and as directed. |
| 100 | M&L for dubbing coat on exposed cement concrete 10 to 20 mm cement plaster 1:4 incl micro concrete with chicken wire mess with water proofing liquid @200 ml per bag up to II nd floor roof levelcomplete all as spd as directed |
| 101 | M&L preparation new or previously untreated steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over and including one coatof red oxide zinc chrome primer complete all as specified anddirected by Engineer-in-Charge. |
| 102 | M&L for preparation of new or previously untreated wooden or wood based surfaces of any description not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint over and including one coatof pink primer complete all as specified and directed by Engineer-in-Charge. |
| 103 | M&L for preparation of old painted wooden or wood based surfaces of any description n.exc 10 cm in width or girth when unconnected with other painting or when painted in a diferenttint and applying one coat of synthetic enamel paint over and including one coat of red oxide complete all as specified and directed. |
| 104 | M&L for complete removal of existing treatment on wall by scrapping with mechanical sander (having mechanical vaccum mechanism ) with sanding pad of appropriate grit to make surface clean ,free from dust ,loose paint etcby skilled labour and applying two coat OBD on wall with airless electric sprayers over a coat of primer applied using airless electric sprayer over one coat of plaster of paris of 1mm thickness complete all as specified and directed. Note:-Application to be done through authorised applicator of manufacturer. |
| 105 | M&L for two coat OBD on newly plastered wall surface with airless electric sprayers over a coat of primer applied using airless electric sprayers over one coat of plaster of paris putty of 1mm thickness complete all as specified and directed. Note-Application to be done through authorised applicator of manufacturer |
| 106 | Demolition of Reinforced Concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed. |
| 107 | M & L for two coats of elastomeric compound i.e super latex of Dr fixit Pidifin 2K/ Pidilite-302 super latex / Fosroc-brush crete / Cico Tape Crete on concrete or brick masonary surface after cleaning(vertical or horizontal) by removing all the loose mortar laitance dirt, dust etc by chisel, hammer, wire brush, jute, brush and air blower. complete all as specified and directed. |
| 108 | M&L for preparation of new surface of plasteredand applying oftwo coat OBD on ceiling with airless electric sprayers over a coat of primer applied using airless electric sprayers over and including 1 mm thick plaster of paris (approved by GE)prepared and sanded with electrically operated sanding machine. Application to be done through the authorised applicator of manufacturer complete all as specified and directed. |
| 109 | M&L applying two coat of white putty on new surface and applying one coat of exterior water based primer by using Airless spray techonology with max working pressure of 3300 PPSI and capable of operating single spray gun with a max material hose lengthof 30 mtr, the spray machine should be of reputed manufacturer with pro guard technology and capability of tracking pressue and paint usage and certified by jpaint manufacturer and as mentioned in PS and accessories fpr applying distemper, should be able to spray in hard to reach areas and penetration of distemper, on the surface to achieve excllent application using limited manpower complete all as specified and directed. |
| 110 | M&L for complete removal of existing treatment, preparation of old decorated plastered or unplastered surfaces of walls / roofprojections including facia,cornices etc. and applying two coat of white putty and applying one coat of primer by using Airless spray techonology with max working pressure of 3300 PPSI and capable of operating single spray gun with a max material hose lengthof 30 mtr, the spray machine should be of reputed manufacturer with pro guard technology and capability of tracking pressue and paint usage and certified by paint manufacturer and accessories for applying Primer, should be able to spray in hard to reach areas and penetration of Primer, on the surface to achieve excllent application using limited manpower complete all as specified and directed. Note : - Sanding of old decorated surface to be done by mechanical sander with 1500 - 2700 rpm, with internal dust extraction system for clean environment certified by paint manufacturer. |
| 111 | M&L for applying two coat of Antifungalweather coat exterior wall finishapplied by using Airless spray technology with max working pressure of 3300 PPSI and capable of operating single spray gun with a max material hose length of 30 mtr the spray machine should be of reputed manufacture with pro guard technology and capability of tracking pressure and paint usage and certified by paint manufacturer and as mentioned in PS and accessories for applying exterior weather proof paint, should be able to spray in hard to reach areas and penetration of exterior weather proof paint on the surface to achieve excellent application using limited manpower complete all as specified and directed. |
| 112 | M&L brushing cement slurry @ 3.00 Kg per Sqm on existing concrete surface. |
| 113 | M&L 25mm thick PCC 1:2:4 type B0( 12.50mm graged aggregate) finished even and fair |
| 114 | M & L for coloured Non skid ceramic tiles 7 to 8 mm thick of colour patteren as approved and as per manufacturers catalouge (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 Sqm, in floor etc over 15mm thick screed bed with cement mortar 1:6and set and jointed in neat cement slurry and pointed in white or coloured cement to match including jambs by making the mitred angles at corners all as specified and directed by Engr in charge |
| 115 | Ditto all as item No 114 but as in skirting with with 10mm CM 1:4 as backing coat complete. |
| 116 | M & L for colouredglazed ceramic tiles 300 mm x450 mm & 7 mm thick on vertical surfaces of colour patteren as approved and as per manufacturers catalouge such as skirting, dados etc, set and jointed in neat cement slurry over and including 10 mm thick bedding layer/ backing coat in CM 1:4 complete and pointed in white or coloured cement to match complete all as specified and as directed by Engineer-In-Charge.Note : Skirting shall be provided to match with colour and size of floor tiles provided in rooms. |
| 117 | S & Fin Repair viterous china wash hand basin of size 550 x 400 mm, white colour flat back excluding taps, chain and plug and porcelean stopper but including brackets and CP waste fittingcompleteall as specified and as directed by Engineer-In-Charge |
| 118 | S&F in repairs 10 litres capacityPVC Valveless symphonic action type flushing cistern high / low level white complete with inlet , ball valve float and handle including brackets and telescopic down flush pipes and jointing with WC complete completeall as specified and as directed by Engineer-In-Charge. |
| 119 | S&Fin RepairPVC connection 15mm size with PTMT nuts, of length 600mm Complete all as specified and as directed by Engineer-In-Charge. |
| 120 | S & F in Repair Fancy type Pillar taps , cast copper alloy , with capstan heads, chromium plated, screwed down high pressure fancy type of15 mm bore size with or without lettered Hot or Coldwith long screwed shanks and flynuts , screwed for iron pipe and fixedComplete all as specified and as directed by Engineer-In-Charge. |
| 121 | S&Fin RepairCast copper alloy CP angle valve type stop cock with flange suitable for 15mm bore pipe screwed at both endsor high pressure with Capstan headconfirmingComplete all as specified and as directed by Engineer-In-Charge. |
| 122 | S&F in Repairbib tapwith flange of bore size 15mm, cast copper alloy, chromium plated,fancy type, with crutch or butter fly handle screwed down , screwed for iron pipe or for brass ferruleComplete all as specified and as directed by Engineer-In-Charge. |
| 123 | S&Fin RepairCast copper alloy CP Concealed stop cock with flange suitable for 15mm bore pipe screwed at both endsor high pressure with Capstan headconfirmingComplete all as specified and as directed by Engineer-In-Charge. |
| 124 | Supply and fixing in repairs CP brass shower rose of size 125 mm saquare/circular as approved swivel type withCP extension rod 15mm dia and 200mm long suitable for 15mm bore pipe .Complete all as specified and directed by Engineer-in-charge. |
| 125 | S&F in Repair Towel ring of PTMT fixed with and including CP brass screws and wooden/plastic cleats (minimumwt 90gms) complete all as specified and directed |
| 126 | S & Fin Repair 600mm x 450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washersComplete all as specified and as directed by Engineer-In-Charge. |
| 127 | S&FStainless Steel Plate Rack SS 304 grade of size 31\"\" x 30\"\" x 10\"\" with using stainless steel sheet of0.63mm thicknessFixed with Rawl plug and screw. completeall as specified and as directed by Engineer-In-Charge. Note : The plate rack shall be of 1st Quality and wt and composition of SS shall be as per IS. |
| 128 | S&F in RepairStainless steel sink with draining board, made out of 1.00mm thick sheet for kitchen or laboratory with plug, washers waste pipe, cast iron cantilever brackets, connecting union overall size 915mmx460mm with bowl size 410mm x 330mm x 160mm .completeall as specified and as directed by Engineer-In-Charge. |
| 129 | ditto All as item No. 128 but 20 mm bore. |
| 130 | M & L for Galvanised Iron tubes 15mm dia medium grade with all fittings and fixtures such as bends , elbows ,tees ,short pieces , back nuts , connectors , diminishing pieces caps pegs and clamps union etc. laid in wall/floor/ceiling as in concealed work including cutting chase in walland making good surface . |
| 131 | S&Ffor Galvanised Iron tubes 20mm dia medium grade with all fittings and fixtures such as bends , elbows ,tees ,short pieces , back nuts , connectors , diminishing pieces caps pegs and clamps union etc. laid in wall/floor/ceiling as in concealed work including cutting chase in walland making good surface . |
| 132 | S&F in repair 20mm dia Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed |
| 133 | Supply and fixing in repair 1000 Litre capacity Rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) three layers hoisted andfixed in position complete andall as specified and as directed by Engineer-in-Charge |
| 134 | M & L for 75mm PVC (SWR) floor trap with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4)completeall as specified and as directed by Engineer-In-Charge (Trap shall be sealed properly with the existing pipe and got tested by Filling with water). |
| 135 | S&F PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement including all excavation and complete embedded in PCC type B1 (20mm graded aggrgate) with cover and including jointing inlet and outlet pipes and and removal of excaveted materials upto 50 mtr distance. |
| 136 | Supply and fixingLow density polyethylene pipes (LDPE) of pressure rating 6 kg/ cm2 of40 mm dia borefor wash hand basin Complete all as specified and directed by Engineer-in-charge. |
| 137 | Demolition and breaking up drain pipes (Salt glazed ware , AC or RCC or PVC Pipes) of any dia including all fittings any size all as specified & as directed by Engr-in-Charge. |
| 138 | S& F PVC (SWR) pipes 110mm dia single, socketed in any length ,with rubber ring joints laid in floorall as directed by Engr in charge. |
| 139 | S&F PVC (SWR) bends with access door 110mm dia complete all as specified and directed. |
| 140 | S&F PVC (SWR) branch piece, single (singleT) equal or unequal 110mm dia complete all as specified and directed |
| 141 | S&F PVC (SWR) branch piece, single (singleT) equal or unequal with access door 110mm dia complete all as specified and directed |
| 142 | S& F PVC (SWR) pipes 75mm dia single, socketed in any length ,with rubber ring joints laid on floorall as directed by Engr in charge. |
| 143 | S&F PVC (SWR) bends with access door75mm dia complete all as specified and directed. |
| 144 | S&F PVC (SWR) 75mm branch piece, single (single T) equal or unequal complete all as specified and directed. |
| 145 | S&F PVC (SWR) 75mm branch piece, single (single T) equal or unequal with access door complete all as specified and directed. |
| 146 | S&F PVC (SWR) 110mm dia vent cowl complete all as specified and directed. |
| 147 | Excavating in trenches, n exc 1.50m wide and n exc 1.50m in depth; for foundations, etc. or for manholes etc not exc 10 Sqm on plan andnot exc 1.5m in depth and getting out in soft/loose soil.Complete all as specified and directed by Engineer-in-charge. |
| 148 | M & L for reinforced cement concrete pipes class NP-2 laid in jointed complete with collers ,bore of pipe 150mm Complete all as specified and directed by Engineer-in-charge. |
| 149 | M & L for cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate, bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested; in bore of pipe 150mm.Complete all as specified and directed by Engineer-in-charge. |
| 150 | Returning, filling in,including spreading, leveling, watering and well ramming in layers not exc 25cm thick with soils.Complete all as specified and directed by Engineer-in-charge. |
| 151 | Removing surplus excavated material (Soils) to distance of exc. 250 m bu n. exc. 500 m and depositing where directed at a level n. exc. 1.5 m above the starting point. completeall as specified and as directed by Engineer-In-Charge. |
| 152 | M & L for cement concrete 1:3:6 type C2 using 40mm graded stone aggregate in foundations, filling and mass concrete including filling around pipes.Complete all as specified and directed by Engineer-in-charge. |
| 153 | M & L for cement concrete 1:2:4 type B1 using 20mm graded stone aggregate in Coping/Channels in side the manholes/ benching etc including formwork and weathering/ slightly rounded or champhered angle making the surface even and fair Complete all as specified and directed by Engineer-in-charge. |
| 154 | Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using ex- tra cement, including forms, moulds, mi- tred/stopped ends etc. |
| 155 | M&L for Precast Man hole covers type B1 1:2:4 (20 mm graded aggregate) of size as per site requirement including finishing the surfaces even and smooth including making holes and inserting MS conduit pipe with provision of MS Round bar 10mm dia made in shape for lifting the MH cover 2 nos with each cover Complete all as specified and directed by Engineer-in-charge |
| 156 | S&F framed work such as grills of approved design used square bar of frame of MS hellow square tubes framed guard bars etc., andsimilar work conforming to Fe-410-0 or Fe-310-0.compete all as specified as directed by Engineer -in -charge |
| 157 | M&L for Granite (of any colour or any grains as approved) work with 20mm thick table rubbed and polished as in steps jambs , pillers , window cills, cooking platform and similar works including pointing in with cement using 1:2 using marbel dust and admixture of pigments to match with the shade of granite over and including 15mm thick screed bad in CM 1:6 for laying granite all as specified and directed including taking down / dismanteling of existing plaster/ stone of any type. |
| 158 | M&L for drilling holes for pipes etc in cadappa/graniteincluding RCC slab nexc 25mm dia and n exc 150mm depth complete all as specified and directed. |
| 159 | Demolition of reinforced cement concrete in any position like roofs, floors other than ground floors , beam , staircases , landings , chajjas,projections, facias and similar suspended work or reinforcement cut as required to facilate demolition for portions ordered to be dismanttled up to 15 m height including forwork and necessary saftey measuresor as directed by Engr in charge |
| 160 | M&L for reinforced cement concrete type B1 (1 : 1 1/2 :3)nominal mix using 20 mm graded broken stone aggregate as inslabs supported on walls, beams and columns in floors, roofs, landings, shelves and the like. |
| 161 | M&L for Formwork to sides and soffits of floor or roof beams, beam haunchings,girders, bressummers,lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. complete all as specified and as directed by Engineer-In-Charge. |
| 162 | S&F mild steel TMT bar of 10 mm dia and over cut to length bent to shape required including cranking and binding with mild steel annealed wire not less than 0.9 mm dia complete all as specified and directed |
| 163 | M&L Brick work with subclass `B\" bricks, straight or curved on plan exc 6m mean radius, built inCM1 : 6 all as specified and directed by Engr-in-Charge |
| 164 | M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan to anyradius in half brick thickbuilt in cement mortar 1:4 complete all as specified and directed |
| 165 | Taking down cement plaster on brick or stone walls, etc.including raking out joints, hacking for key, scrubbing down with water, etc. |
| 166 | M&L for 10 mm thick cement plaster in CM 1:6 on brick surface finished even and smooth without using extra cement including in patches Complete all as specified and directed by Engineer-in-charge. |
| 167 | M&L for 15 mm thick cement plaster in CM 1:4 on brick surface finished even and smooth without using extra cement including in patches Complete all as specified and directed by Engineer-in-charge. |
| 168 | M &L for preparation ofnewlyplastered surfaces at walls and applying the 2 coat of Oil bound distemper over 1 coat of primer Complete all as specified and directed by Engineer-in-charge. |
| 169 | M&L preparation of newly plastered surface of wall and applying 2 coats of cement based paint over a coat ofprimer complete. |
| 170 | M & L two coats of synthetic enamel paint over one coat of red oxide primer on steel based surface exc. 10cm width or girth including preparation of new or previously untreated surfaces.compete all as specified as directed by Engineer -in -charge |
| 171 | S&F 2nd class hardwoodPlain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified and directed |
| 172 | S&F Powder coated aluminium sliding windows frame with movable shutter (sliding on minimum two PVC roller of best quality, for each shutter on threetracks with stainless steel mosquito proofing and glazing shutter and incl 5.50 mm thick glass & stainless steel wire messs fixed with neoprene rubber gasket with aluminium beading, clips,frame made with aluminium section as appended below-(i) Window frame :63x35mm X 1.48 mm thick for three tracks.(ii) Top/bottom rail and style / rail of shutter : 19x38x1.48mm thick and over.(iii) Aluminium beading - 0.7mm thick(iv) stainless steel wire cloth 0.45mm nominal dia of wire and average width of aperature 1.40mm and fixed in aluminium window or alongwith F/Y section fixed with aluminium wire staples complete.(v) Aluminium fittings suchaluminium suitable handle with auto interlocking closing(vi) Making good of wall surfaces to match with existing surfaces complete all as specified and directed. |
| 173 | S&F Powder coated aluminium ventilators box type with louvers & wire mesh fixed with neoprene rubber gasket, aluminium beading, clips. Frame made with powder coated aluminium section of size as appended below (i)frame :45.2mm x35mm X 1.15 mm(ii) Aluminium beading - 0.7mm thick (iii) Glass louvers depth 6 inch. Blade Angle: 38 degrees and thickness of blade 2.02 mm with 106.25 mm spacing.(iv) Aluminium neccessary fittings complete as required basis. (v) Making good of wall surfaces with silicon to match with existing surfaces complete all as specified and directed. |
| 174 | S & F for 35mm thick factory made Plain, framed,panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats (Shutters shall be brought at site without primer and got approved by Engr-in-Charge/ GE.) |
| 175 | S & F35 mm thick second class hard wood Glazed and skeleton shutters, open rebated and prepared to receive gauze, glass etc., (withsash bars) divied into into sqare and half portion panel upto middle rail and will be provided with 12mm thick pre laminated board laminated on both side and edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc., sizess of members of shutters as specified inSSR Part I, Section 8, clause 8.20 (a)compete all as specified as directed by Engineer -in -charge |
| 176 | S & F Solid PVC door frame of size 50 mm x 47 mm made out of 10 mm plain colour PVC sheet reinforced with MS square tube, supplying and fixing in opening as per specification & drawing compete all as specified as directed by Engineer -in -charge |
| 177 | S & F Factory made solid panel PVC Moulded door shutter 28 to 30mm thick(stiles), with 2, 4, or 6 raised paneldesign 2mm thickPrelam PVC sheet on the front face and 2mm thick Plain colour PVC sheet on back face with particle Board core compete all as specified as directed by Engineer -in -charge |
| 178 | S & F 100 mm MS butt hinges medium weight cold rolled mild steel compete all as specified as directed by Engineer -in -charge |
| 179 | S & F150 mm aluminium anodised barrel tower bolts of extruded section,ISI marked compete all as specified as directed by Engineer -in -charge |
| 180 | S & F Continuous (piano) hinges, width of flaps 30mmmild steel, bright finish or electrogalvanised complete all as specified and directed |
| 181 | S&F 100mm Aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed |
| 182 | S&F 100mm Hasp and staple, safety type, brass with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed |
| 183 | S & F 300 mm longand Mild steel Chromium plated sliding door bolts, plate type,with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed compete all as specified as directed by Engineer -in -charge |
| 184 | M & L two coats of synthetic enamel paint over one coat of pink primer on wood or wooden based surface exc. 10cm width or girth including preparation of new or previously untreated surfaces.compete all as specified as directed by Engineer -in -charge |
| 185 | S & F in repair18/19mm thick prelaminatedparticle board exterior grade medium density, one side with decorative choice lamination and the other side balancing white lamination as in panels of partitions/ cup board shelves including providing wooden brackets minimum 25mmx25mm and long as depth of cupboard for support of laminated boardsand the like fixed in wooden frame withwooden beading compete all as specified as directed by Engineer -in -charge |
| 186 | S & F in repairs curtain rod of metalic 25 mm dia Harrison rails, mild steel, chromium plated including long projected bracket of heavy section both sidefixed in position by drilling holes in walls and fixed the brackers with rawl plug and steel screw compete all as specified as directed by Engineer -in -charge |
| 187 | M & L for cement concrete type C2 (1:3:6) (40 mm graded broken stone aggregate)75 mm thick as in plinth protection and finish even and fair all as directed by Engr in Charge |
| 188 | M&L for Forming Construction joint 30mm deep x 10mm wide filled with sealing compound of Grade A complete all as specified and directed. |
| 189 | Dismanteling of wooden truss/ scanteling purlin rafter etc. |
| 190 | S&F steel work in rolled section as approved, purlins, rafter, posts, gusset plates cleats, wind tiesetc including special shape washers etc complete using ERW or induction butt welded tubes confirming to IS 116-1979 grade (medium grade) |
| 191 | S&F Horizental level suspended Ceiling comprising of Armstrong GI Clip-in Micro perforated 600x600mm (nominal size) tiles of 120mm galvanised steel as per IS 277 (2003) suitable for architectural finishes in 0.5mm thickness as per in IS:513 (1994) in Global white colour with concealed suspension syayetm having a bevelled edge of 3x3mm and height of 33mm on one side and 18mm on other side. Tile shall have perforated of hole diameter 2.5mm and open area 16% with linear and diagonal pitch of 5.5mm and 7.7mm respectively along with a border of 10mm. The tile shall be electrostaticalkly polyster powder coated using RoHS compliant powder having coating thickness ranging from 60-80microns. Back side of the tile shall have Soundtex fleece hot pressed mechanically for uniform bonding to achieve NRC up to 0.7all asper manufactures instructions , complete all as specified and as directed by Engineer-In-Charge.Note : If electrical cables are running at site aand required to be relocated electric fittings on walls are required to be shifted including refixing of fan/ light fittings and other light acessarry including making good the wall surface.shall be deemed to be included to the rates. |
| 192 | Dismantling wall/ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, complete. |
| 193 | Taking down carefully copper/aluminum point wiring (light, fan, socket or power) complete with fittings and fixtures such as switches, ceilingroses, pendants, regulators, socket, lamp holders brackets, bulk head fittings, tube light fittings etc complete and removing allretrieved materials toMES storesfor segregation of serviceable /Unserviceable fitting&fixture and also making good disturbed surfaces of wall, floors etc complete all asspecified and as directed by the Engineer-in-Charge. |
| 194 | M&L point wiring complete with single core FRLS PVC insulated, unsheathed, multi stranded copper conductor cables 1.5 Sqmm 1100 volts grade, with and incl 1.5 Sqmm FRLS PVC insulated, unsheathed, multi stranded copper conductor cables as continuous earth wire connected to metallic bodies of luminaries / fans etc at one end and to common earth dolly at other end, complete wiring drawn through &including PVC Conduit (Concealed in wall/ceiling) of size 20mm dia and above (as per conductor run ) medium grade, ISI marked, incl all accessories & fittings / junction boxes / inspection covers etc, with and incl concealed MS sunken box of suitable size flush with wall surface, suitable for fixing of Modular type switches / sockets etc, complete all as specified and directed for the following :-Note : 1. Modular white cover plate shall be measured and paid separately2. Rate quoted shall deemed to be inclusive of cutting chasing and making good of disturbed surface of wall / floor/ ceiling etc as original by brick work, plastering, white washing, OBD etc as required, complete all as directed. |
| 195 | All as per item No 193 above, but for one 3 pin socket outlet 5 Amp on same board complete all as specified and as directed by the Engineer-in-Charge. |
| 196 | All as per item No 193 above, but for one 3 pin socket outlet 5 Amp on independent board complete all as specified and as directed by the Engineer-in-Charge. |
| 197 | All as per serial item No 193 here-in-before, but for one socket outlet 15 Amps on independent board with 2.5 Sqmm copper conductor (Multi-stranded) insulated and unsheathed electric cable 1100 volts (ISI Marked) including PVC insulated and unsheathed electric cable 1100 volts 2.5 Sqmm copper stranded conductor as continuous earth wire connected to common dolly complete all as specified and as directed by Engineer-in-Charge. |
| 198 | One bell/ buzzer point controlled by one push button on the same board with other switches or independent with cables 1.5 sq.mm size |
| 199 | S&F Modular Switch 1 way 16 Amps, 1 Module size complete all as directed.. |
| 200 | S&F Modular Socket 6 A, 2/3, Pin 2 Module size complete all as directed.. |
| 201 | S&F Modular Socket 6A/16 A, 5 Pin ,2 Module size complete all as directed.. |
| 202 | S&F Modular Switch 1 way 6 Amps, 1 Module size complete all as directed.. |
| 203 | S&F Modular Bell push 6A 1 module complete all as specified and directed |
| 204 | S&Felectric call bell ding dong AC 230 volts Single Pole complete all as specified and directed. |
| 205 | Supply and fixing ceiling rose, surface bakelite, 65 x 50 mm, three terminals complete all specified and as directed by the Engineer-in-Charge. |
| 206 | Supply and fixing angular lamp holder, metal cased body of brass with back plate inbatten fittings, including Plastic square box of required size complete all as specified and directed by the Engineer-in-Charge |
| 207 | S&F LED Bulb 9 Watt complete all specified and as directed by the Engineer-in-Charge |
| 208 | Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete |
| 209 | Supply and fixing in replacement LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete |
| 210 | S & F in replacement LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size.. |
| 211 | S&F in replacement of street light fitting bracket, 1.5 mtr long made out of galvanized iron pipe of 40 mm dia size light grade complete with and incl 02 nos MS clamp made of MS flate iron of 50 x 6 mm size with nut, bolts, washer etc with and incl two coats of aluminum paint over a coat of red oxide primer, complete all as directed. |
| 212 | S&F in replacement LED street light luminaire of 35 Watt capacity, made of single piece pressure die-cast aluminium housing with high power LED with lens for proper light distribution luminiaries, IP 66, with toughned glass cover and incl control gear etc, with and incl making all electric connection, complete all as specified and directed by Engineer in charge. |
| 213 | Supply and fixing in replacement sheet Metal enclosure double shutter type for DB’s 240 Volts Single Pole and Neutral 12 way with 200 Amps rated bus bar complete complete all as specified andas directed by the Engr-in-Charge.. |
| 214 | Supply and fixing in replacement SPN 40 amp rating 240V, 10KA \"C\" curve miniature circuit breaker (MCB) of Single pole and neutral in the MCB DB complete with connection testing and commissioning. |
| 215 | Supply and fixing in replacement SP 5 to 32 amp rating 240V, 10KA \"B\" curve miniature circuit breaker (MCB) of Single pole and neutral in the MCB DB complete with connection testing and commissioning. |
| 216 | M&L for sub main wiring with 2 run of 4 Sqmm FR, PVC insulated, unsheathed and stranded copper conductor cable with and incl 4 Sqmm (nominal area) FRLS, PVC insulated, unsheathed and stranded copper conductor cable as earth wire connected with thimble from main DB to sub main DB, drawn drawn through & PVC conduit of size 20 mm and aboveincl all conduit accessories & fittings / junction boxes / inspection covers etc, with and incl cutting chasing and making good of disturbed surface of wall / floor/ ceiling etc as original by brick work, plastering, white washing, OBD etc as required, complete all as directed complete incl taking out old wiring and conduitNote : 1. The cost of concealed conduit , taking down old wiring & accessories is deemed to be included in quoted rates.2. The two run of 6 Sqmm wire and one run of 4 Sqmm wire will be measured as one unit. |
| 217 | Earthing complete withgalvanized steel earth plate electrode 60 cmx 60 cm x 6 mm thick buried directlyin ground (earth pit notless than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 metres below normal ground level,connecting to theGalvanized ironearth wire 4.0 mm dia by means of bolts, nuts , check nuts and washers of galvanized iron andsteelearth wire protected by provision of GI lightgrade pipe15 mmbore including provision of concrete pitmade from PCC ( 1:2:4) type B-1 (using20 mm graded stone aggregate) with 40mm thick cover of RCC 1:2:4 reinforced with XPM (Weight not less than 4 Kg/Sqm) and frame of angleiron40 x 40 x 6 mm and handle of 6 mmdia MS barmade to shape, GI light grade 20 mmbore pipefor watering perforated atbottom, 1.50metre long placed on top edge of earth plate, common salt &charcoalfilling, withfixing arrangement , funnel, wire mesh and earthwork in hard/dense soil, returning filling in and removal of surplus soilto a distance notexceeding50 metres, all as perelectrical plateNo 3 of SSR 2020 Part-I and connecting toMCBDB’searth test point all as specified or indicated including testing on completion . |
| 218 | Supply and fix exhaust fan made of iron body complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300mm |
| 219 | Supply and fix electric water heater, storage type steel body with copperinner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc |
| 220 | Taking down the old serviceable electric meter and keeping in safe custody includingrefixing the sameincluding necessary electric wire, flexible pipe and PVC conduitfrom DB to Meter and fixing accessories required as per site requirementcomplete all as specified and directed by Engr-in-Charge |
| 221 | Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) |
| 222 | M & L Taking down fan, sealing cable end, dismantling blades and removing fan and blades to store, |
| 223 | S&F in replacement DBOX MCB protected Socket plastic base dimension 415 x 375 x 225mm 4 module raise neutral linkcomplete with one single pole MCB 20 Amp \"C\" Series 240 VOLT |
| 224 | Supplying and fixing 1100 volts grade heavy duty cable PVC insulated aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire, one twin core cable flat or circular of size 6 sqmm |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2025 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
