|
| 1 | Taking down cement plaster of any description on PCC/stone surface/brick surfaces including raking out joints, hacking for key scrubbing down with water etc and removal of entire debris as ordered outside MoD land complete all as specified and as directed. |
| 2 | Demolition of brickwork/PCC block or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc and removal of entire debris as ordered outside MoD land complete all as specified and as directed. |
| 3 | Demolition of cement concrete (un-reinforced) in ground floor and paving not exceeding 15 cm thick (above or below ground level) and removal of entire debris as ordered outside MoD land complete all as directed. |
| 4 | Dismantling of timber scantlings 40 Sq cm and over in section in any position unframed work and stacking at site where directed complete. |
| 5 | Dismantling of wooden battens for tiles, shingles etc of any size including tilting fillets exc 15 cm spacing complete and stacking where directed. |
| 6 | Dismantling of wrought iron or mild steel work of any description and from any position not otherwise provided for in this Schedule (BOQ), complete all as specified and as directed. |
| 7 | Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings and stacking at site where directed and removal of debris as ordered outside MoD land complete all as specified & as directed. |
| 8 | Dismantling of Asbestos cement Corrugated or semi corrugated sheets etc any thickness including ridges as in roof covering and stacking at site where directed and removal of debris tooutside MoD land and depositing where directed complete all as specified and as directed. |
| 9 | Dismantling mangalore pattern roofing tiles with ceiling tiles or slate roofing including ridges complete all as specified & as directed. |
| 10 | Dismantling wall and ceiling board (fibre, pulp, insulation etc.) or insulation boards/ slabs/ blankets, any thickness including cover fillets complete all as specified and as directed. |
| 11 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), stackingserviceable tiles at site andremoval of entire debris as ordered outside MoD land complete all as specified and as directed. |
| 12 | M&L for factory madepre cast cement concrete 1:3:6 type C1 (using 20 mm graded crushed stone aggregate) block masonry with solid blocks, exceeding 10 cm in width and setting in cement mortar 1:6 complete all as specified & as directed. |
| 13 | M&L for factory made pre cast cement concrete 1:3:6 type C1 (using 20 mm graded crushed stone aggregate) block masonry with solid blocks or slabs, 10 cm thick (with plain or interlocking joints as directed) and setting in cement mortar 1:4 in walls complete all as specified & as directed. |
| 14 | Supply only Integral Water Proofing Compound (ISI Marked). |
| 15 | Cutting chases in brick/ stone wall, pinning in, making good to facing where required and plastering in CM 1:4 to ends of edges of landing, steps, cills, lintelsetc and cutting chasesexceeding 10 cm but not exceeding 20 cm girth for concealed water tubing and similar works and making good cutting as per its original specfication complete all as directed. |
| 16 | M&L for Second class hard wood well seasoned wooden scantling clean sawn unframed fixed complete all as directed. |
| 17 | Fixing only hard wood scantling clean sawn unframed fixed complete all as directed. Note : Wooden scantling obtained serviceable from item No 4 here-in-above shall be used under this item. |
| 18 | M&L for Second class hard wood battens spaced at 30cm centre to centre, clean sawn, cross sectional area exceeding 15 sqcm but not exc 25 sqcm, complete all as specified and as directed. |
| 19 | Fixing only hard wood battens spaced at 30cm centre to centre, clean sawn, cross sectional area exceeding 15 sqcm but not exc 25 sqcm, complete all as specified and as directed. Note : Hard wood battens obtained serviceable from item No 5 here-in-above shall be used under this item. |
| 20 | S&F rolled mild steel sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, steel ladders etc fixed with angle cleats or other connecting plates etc conforming to Fe-410 W (Gde E-250) quality-A complete all as specified and as directed. |
| 21 | S&F rolled mild steel work as in Plates (plain or chequered) channels. Square cut or notched (ordinary and counter sunk) forming holes, with bolted or welded attachment, including necessary welding etc. conforming to Fe-410-W (Gde E-250) quality `A’ complete all as specified and as directed. |
| 22 | M&L for expanded metal weight not exceeding 4 Kgs per Sqm, cut to length, bent to shape required and tying with and including annealed mild steel wire not less than 0.9mm dia or fixing with galvanised steel staples supplied and fixed complete to wood or steel members complete all as specified and as directed. |
| 23 | S&F 0.63mm thick galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with L-type or J-type or cranked hook bolts and washers, in roofs, walls etc. with grade of zinc coating 275 complete all as specified & as directed. |
| 24 | S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof coverings/ ridges/ cladding to walls, fixed with self tapping screws complete all as specified & as directed.Notes : (i) Colour of sheet shall be as approved by the GE. (ii) Quoted rates shall deemed to be inclusive of scaffolding, safety net, safety belt, etc |
| 25 | S&F pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof coverings/ cladding to walls, ridges, gutters, valleys etc. fixed with self tapping screws complete all as specified & as directed.Notes : (i) Colour of sheet shall be as approved by the GE. (ii) Quoted rates shall deemed to be inclusive of scaffolding, safety net, safety belt, etc |
| 26 | M&L for Roof tiles, Mangalore pattern, interlocking at side joints, laid dry including cutting holes through tiling for pipes and making good the disturbed surface to its original specification complete all as specified and as directed. |
| 27 | All as per item No. 26 here-in-above, but except roof tiles. Note : Roofing tiles obtained serviceable from serial item No 9 here-in-above shall be used under this item. |
| 28 | M&L for Ridge or hip tiles to suit Mangalore pattern of roofing tiles, bedded and jointed in cement mortar 1:6 complete all as specified and as directed. |
| 29 | S&F 6 mm thick calcium silicate board of siliceous and calcareous material reinforced with cellulose fibre board with frame work with screws fixed to false ceiling with and including MS powder coated (white) snap Grid of size 605x605 mm frame work using 24mm x 32mm x 0.7mm main ‘Tee’ runner to be interlocked, 24mm x 32mm x 0.70mm cross ‘Tee’ and 24mm x 32mm x 0.70mm angles fixed to wall for ceiling including necessary supporting hanger with 2 to 3 mm dia GI wire (upto 3.5m long adjustable) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 24x7mm size 60mm long for securing frame work to ceiling suspended @ 1200mm centre to centre both way with PVC rawl plug with & including 6mm thick calcium silicate board as described fixing with clips etc. and ceiling board fixed as per manufacturer’s instructions, with & including painting the ceiling board with two coats of oil emulsion distemper (OBD) of approved shade over a coat of primer on ceiling with & including taking down existing electrical fittings/fixtures and wiring in ceiling and re-fixing the same to its original position or different locations, after completion of false ceiling work including testing on completion as ordered complete all as specified & as directed. |
| 30 | M&L for 75 mm thick plain cement conctere 1:3:6,type C1 (using 20 mm graded crushedstone aggregate) as in plinth protection, hard standing, etc, finished the surface even and smooth without using extra cement, complete all as specified & as directed.Note : Plinth protection shall be of width as directed and shall belaid with an outward slope of 1:40 in alternative bays not exceeding 2.5 meter in length. Joints of 6 mm wide and 10 mm deep shall be provided along the wall and bays and same shall be filled with bitumen mastic filling comprising 1 part of heated bitumen Blown grade any penetration and 3 parts of sand (all by weight). Quoted rate of this item shall deemed to include this provision. |
| 31 | M&L for average 25mm thick plain cement concrete 1:2:4 type B0 (using 12.5mm graded crushed stone aggregate) as in levelling course, floors, etc finished fair & even complete all as specified and as directed. |
| 32 | M&L for 16 to 18 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms, wash basin counter and the like, set in cement mortar 1:4 including pointing in white cement 1:2 using marble dust with admixture of pigment to match with shade of granite over & including 15mm thick screed bed in cement mortar 1:6 complete all as specified and as directed. |
| 33 | M&L for non skid ceramic tiles (coloured) 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm as in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and as directed.Notes : (i) Quoted rate shall deemed to be inclusive of cement screed/ plaster. (ii) Colour of tiles shall be got approved from GE before incorporation in the work. |
| 34 | M&L for non skid ceramic tiles (coloured) 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and as directed.Notes: (i) Quoted rate shall deemed to be inclusive of cement screed/ plaster. (ii) Colour of tiles shall be got approved from GE before incorporation in the work. |
| 35 | M&L for glazed ceramic coloured tiles, 7 to 8mm thick, area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm (i.e. 600mm x 300mm or as directed by Engineer-in-Charge), on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10 mm thick back coat in CM 1:4 complete all as specified and as directed.Notes : (i) Quoted rate shall deemed to be inclusive of cement screed/ plaster. (ii) Colour of tiles shall be got approved from GE before incorporation in the work. |
| 36 | M&L for Rendering 20 mm thick in cement mortar 1:4 on stone masonry surfaces or surfaces other than fair faces of brick work of walls with WPC mixed @ minimum 2% by weight of cement or as per manufacturer instructions and finished the surface even and smooth without using extra cement complete all as specified and as directed. Note : WPC shall be measured and paid for separately as \"Supply only\". |
| 37 | M&L for rendering 15mm thick in cement mortar 1:6 on fair faces of brick masonry or concrete surfaces of walls, finished even & smooth without using extra cement complete all as specified and as directed. |
| 38 | M&L for rendering 10 mm thick in cement mortar 1:3 on fair faces of brick work or concrete surfaces in ceiling finished even and smooth without using extra cement complete all as specified and as directed. |
| 39 | M&L for application of high build polymer modified cement mortar (1:3) mixed with 6 ltrs SBR latex per bag of cement {Compressive strength after 28 days ≥ 40 N/sqmm (According to ASTM C109)} in small patch work over column/ beams/ ceilings / walls surfaces 20 to 30mm thick in two layers over a coat of bonding agent like Nitobond SBR (1 ltr SBR + 3 Kg cement) applied as per manufacturer’s instructions for height upto 15 metre from average ground level complete all as directed by the Engineer-in-Charge. Note :- SBR latex chemical shall be measured and paid for separately as ‘Supply only’. |
| 40 | Supply only SBR latex chemical of Make Krishna Conchem / Dr. Fixit / SIKA / Fosroc / Pidilite / BASF / Sunanda / Asian as approved by GE. |
| 41 | M&L for preparation of newly plastered / unplastered surfaces of ceilings & applying three coats of white wash complete all as specified and as directed. |
| 42 | M&L for preparation of old surfaces of ceilings including scraping down smoke soot, moulds, moss and efflorescent salts, trading oil and greasy spots etc by hand held sander / long handle sander including cornices, pilasters etc (Plastered or unplastered surfaces) and applying one coat of white wash complete all as specified and as directed. |
| 43 | M&L for preparation of new plastered surfaces of walls and applying two coats of oil emulsion distemper (OBD) of approved shade/tint over a coat of primer over & including 1mm thick layer of white cement based wall care putty complete all as specified & as directed. |
| 44 | M&L for preparation of old decorated surfaces of walls including cornices etc (plastered or unplastered) of any description, rubbing, scrappingby hand held sander / long handle sander and washing and applying one coat of oil emulsion distemper (OBD) of approved shade/tint by mechanicalmeans/ auto roller including filling undulations with white cement based wall care putty mixed with multi purpose mixer complete all as specified and as directed. |
| 45 | M&L for preparing newly plastered surface of walls and applying two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of shade as approved by Engineer-in-Charge (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over & including 1mm thick water proof wall care putty suitable for exterior surfaces exposed to weather as per manufacturer\"s instructions complete all as specified and as directed. |
| 46 | M&L for preparation of old decorated surfaces of walls including cornices etc (plastered or unplastered) of any description, rubbing, scrapping by hand held sander / long handle sander and Jet pressure washing and applying one coat of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of shade as approved by Engineer-in-Charge (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm applied by mechanicalmeans i.e Airless spray complete all as specified and as directed. |
| 47 | M&L for preparation of old painted surfaces of wood and wood based material of any description over 10 cm in width or girth and applying two coats of 1st quality synthetic enamel paint of approved tint complete all as specified & as directed. |
| 48 | M&L for preparation of new steel and iron surfaces of any description over 10 cm in width or girth and applying two coats of 1st quality synthetic enamelpaint of approved tint over a coat of zinc chrome primer complete all as specified & as directed. |
| 49 | Taking down or up damaged/ old GI pipe of 15 mm bore and S&F new 15 mm bore galvanized steel water tubing medium grade (ISI marked) with all new fittings (ISI marked) fixed to wall and ceiling or laid in floors complete all as specified and as directed. |
| 50 | Taking down or up damaged/ old GI pipe of 20 mm bore and S&F new 20 mm bore galvanized steel water tubing medium grade (ISI marked) with all new fittings (ISI marked) fixed to wall and ceiling or laid in floors complete all as specified and as directed. |
| 51 | Taking down or up damaged/ old GI pipe of 25 mm bore and S&F new 25 mm bore galvanized steel water tubing medium grade (ISI marked) with all new fittings (ISI marked) fixed to wall and ceiling or laid in floors complete all as specified and as directed. |
| 52 | S&F in repairs 32mm outer diameter CPVC pipes SDR 11 & Plain CPVC SDR 11 Fittings such as bends, elbows, unions, end pieces, etc and fixed with solvent cement fixed to walls and ceilings or laid in floors complete all as specified and as directed. |
| 53 | S&F in repairs 20mm outer diameter CPVC pipes SDR 11 & Plain CPVC SDR 11 Fittings such as bends, elbows, unions, end pieces, etc and fixed with solvent cement fixed to walls and ceilings or laid in floors complete all as specified and as directed. |
| 54 | S&F in repairs 20mm bore Gun metal gate valve (ISI marked) with iron wheel head, screwed both ends for iron pipe, complete all as specified & directed. |
| 55 | S&F in repairs 25mm bore Gun metal gate valve (ISI marked) with iron wheel head, screwed both ends for iron pipe, complete all as specified & directed. |
| 56 | S&F in repairs ball valve, high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball, screwed for iron pipe or brass ferrule of 20 mm bore and fixed (minimum weight 210 gms) complete all as specified and as directed.. |
| 57 | S&F in repairs 15mm bore bib tap with wall flange, fancy type, cast copper alloy, chromium plated screwed for iron pipe or for brass ferrule complete all as specified and as directed. Make: Prayag Cat No. 6506 or equivalent in makes mentioned in Appendix \"B\" here-in-after. |
| 58 | S&F in repairs 15 mm bore bib tap long nose with wall flange, fancy type, cast copper alloy, chromium plated, long shank screwed for iron pipe or for brass ferrule complete all as specified and as directed. Make: Prayag Cat No. 6509 or equivalent in makes mentioned in Appendix \"B\" here-in-after. |
| 59 | S&F in repairs 15 mm bore bib cock sink tap regular spout (W/M) with flange, fancy type, CP cast copper alloy, with capstan heads, with long screwed shanks and fly-nuts, screwed down high pressure, screwed for iron pipe complete all as directed. Make: Prayag CatNo. 6816 or equivalent in makes mentioned in Appendix \"B\" here-in-after. |
| 60 | S&F in repairs 15 mm bore two way angle cock with wall flange, chromium plated brass, screwed both for iron pipe or brass ferrule complete all as directed. Make: Prayag Cat No. 6511 or equivalent in makes mentioned in Appendix \"B\" here-in-after. |
| 61 | S&F in repairs 15 mm bore two way bib tap fancy type, brass, chromium plated with flange and aerator, screwed for iron pipe or for brass ferrule complete all as specified and as directed. Make: Prayag Cat No. 6512 or equivalent in makes mentioned in Appendix \"B\" here-in-after. |
| 62 | S&F in repairs health faucet brass chromium plated with 1.2 mtr SS Chrome plated EPDM tube & ABS hook and wall hook mounted type complete all as specified and as directed.Make:Prayag Cat No. BEA-85 or equivalent in makes mentioned in Appendix \"B\" here-in-after. |
| 63 | S&F in repairs 15 mm bore pillar taps, fancy type, CP cast copper alloy, with capstan heads, with long screwed shanks and fly-nuts, screwed down high pressure, with or without lettered \"Hot\" or \"Cold\" screwed for iron pipe complete all as directed. Make : Prayag CatNo PIS-02 H or equivalent in makes mentioned in Appendix \"B\" here-in-after. |
| 64 | S&F in repairs 15 mm bore pillar tap, Swan neck, fancy type, long body, CP cast copper alloy, with capstan heads, with long screwed shanks and fly-nuts, screwed down high pressure, screwed for iron pipe complete all as directed. Make: Prayag CatNo. 6814 or equivalent in makes mentioned in Appendix \"B\" here-in-after. |
| 65 | S&F in repairs 15 mm bore angle cock with wall flange, chromium plated brass, screwed both for iron pipe or brass ferrule complete all as directed. Make: Prayag Cat No. 6810 or equivalent in makes mentioned in Appendix \"B\" here-in-after. |
| 66 | S&F in repairs concealed type stop valve with wall flange 15 mm bore of pipe, brass chromium plated, screwed down, high pressure, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed. Make: PrayagCat No. 6518 or equivalent in makes mentioned in Appendix \"B\" here-in-after. |
| 67 | S&F in repairs 15 mm bore, brass, chromium plated, wall mixer with L bend and one for shower rose, screwed down high pressure with long screwed shanks and fly nuts, screwed for iron pipe complete all as directed. Make: Prayag Cat No. 6675 or equivalent in makes mentioned in Appendix \"B\" here-in-after. |
| 68 | S&F in repairs 15 mm bore, brass, chromium plated, central hole WHB mixer W/O pop up for hot and cold water mixing, screwed for iron pipe complete all as directed. Make: Prayag Cat No. 6850 or equivalent in makes mentioned in Appendix \"B\" here-in-after. |
| 69 | S&F in repairs chromium plated 110mm square over head ABS shower with SS Arms & Flange, swivel joints fixing to steel pipes etc complete all as directed. Make : Prayag CatNo BS-72N or equivalent in makes mentioned in Appendix \"B\" here-in-after. |
| 70 | S&F in repair CP brass soap dish including fixing with brass screws complete all as specified & as directed. Make : Prayag Cat No BA-45 or equivalent in makes mentioned in Appendix \"B\" here-in-after |
| 71 | S&F in repairs Brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges fixed on wall with PVC rawl plug & chromium plated brass screws complete all as specified and as directed. Make : Prayag Cat No BA-40 or equivalent in makes mentioned in Appendix \"B\" here-in-after. |
| 72 | S&F in repairs CP brass towel ring fixed on wall with PVC rawl plug & chromium plated brass screws complete all as specified and as directed.Make : Prayag Cat No BA-41 or equivalent in makes mentioned in Appendix \"B\" here-in-after. |
| 73 | S&F in repair CP brass towel rack 600mm (24\") long fixed on wall with PVC rawl plug & chromium plated brass screws complete all as specified and as directed. Make: Prayag Cat No. BA-03 or equivalent in makes mentioned in Appendix \"B\" here-in-after. |
| 74 | S&F in repairs grating square 140 mm size of stainless steel and fixed complete all as specified & as directed. |
| 75 | S&F in repairs PVC connections 15mm dia, 450mm long with PTMT nuts & washers at both ends. |
| 76 | S&F in repairs PVC flexible waste pipe for 32mm dia waste coupling complete all as specified and as directed |
| 77 | S&F in repairs 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints / solvent cement joints laid in floors/ fixed to walls, complete all as specified & as directed. |
| 78 | S&F in repairs 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints / solvent cement joints laid in floors/ fixed to walls, complete all as specified & as directed. |
| 79 | S&F75 mmbore PVC (SWR) bends any radius including jointing the same with solvent cement complete all as specified & as directed. |
| 80 | S&F110 mmbore PVC (SWR) bends any radius including jointing the same with solvent cement complete all as specified & as directed. |
| 81 | S&F in repairs PVC (SWR) floor trap plain with grating including jointing with solvent cement,diameter of outlet 75mm, complete all as specified & as directed. |
| 82 | S&F in repairs 600mm x 450mm looking mirror of selected quality glass not less than 5.5mm thick, beveled edge looking mirror fixed to wooden plug with chromium plated brass screws and cup washers complete all as specified. |
| 83 | S&F in repairs 5 mm thick bevelled edge looking mirror of selected quality glass, mounted on 6mm thick PVC/ AC building board/ commercial plywood, size as directed and fixed with chromium plated brass screws and cup washers complete all as specified and directed. |
| 84 | S&F in repairs bathroom cabinet mirror (400x500mm) including fixing screws complete all as specified and as directed. Make: Prayag Cat No. 554 or equivalent in makes mentioned in Appendix \"B\" here-in-after. |
| 85 | S&F in repairs Corner glass Shelf 300mm with Brass brackets fixed on wall with PVC rawl plug & chromium plated brass screws complete all as specified and as directed.Make : Cat Part No BEA-44 of Prayag or equivalent in makes mentioned in Appendix ‘B’ here-in-after. |
| 86 | S&F in repairs glass Shelf 500 x 125 mm with brass brackets fixed on wall with PVC rawl plug & chromium plated brass screws complete all as specified and as directed.Make : Cat Part No BEA-45 of Prayag or equivalent in makes mentioned in Appendix ‘B’ here-in-after. |
| 87 | S&F in repairs vitreous china wash hand basin, white, flat back of size 550mm x 400mm with & including a pair of cast iron brackets embedded in PCC 1:3:6 type C1 blocks of size 10x7.5x15cm/ suitable fastener bolts, 32 mm dia PVC waste pipe and 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, (excluding tap, waste chain & plug), complete all as specified & as directed. |
| 88 | S&F in repairs vitreous china squatting pan (Orissa pattern) water closet (white) of size 580x440mm with integral foot rests, ‘P’ or ‘S’ trap, including connection to trap and flushing pipe, antisyphonage pipe etc, including lime concrete bedding and making good disturbed floor, complete all as specified and as directed. |
| 89 | S&F in repairs vitreous china wash down water closet pan (Pedestal pattern), white, including connection to drain (or outgoing pipe) and to flushing pipe, anti-sypohonage pipe etc., with plastic WC seat cover (white) closed pattern with flat bottom and cover and mild steel chromium plated or aluminized hinging device, complete all as specified & as directed. |
| 90 | Taking down and re-fixing vitreous china wash down water closet pan padastel pattern including screws and drilling complete all as directed. |
| 91 | Taking down and re-fixing vitreous china wash hand basin of any size including screws and 2 Nos. new brackets or fastener bolts complete all as directed. |
| 92 | S&F in repairs 10 liters capacity PVC valveless, syphonic action type, flushing cistern, low level, white with inlet ball valve, float and handle including brackets and flush pipe of polyetylene of low or high density or 32 mm dia PVC connection pipe complete all as specified and as directed. |
| 93 | S&F sink without draining board, glossy finished, made out of 1.00 mm thick stainless steel sheet for kitchen or laboratory with plug, washers and waste pipe, including bedding in CM to dwarf wall or including fixing cantilever, brackets and connecting union to pipe, overall size 495x420 mm with bowl size 410x330x160 mmincluding 40mm dia waste pipe of polythelene of low or high density, 40mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, making holes in walls for brackets and fixed in CM 1:3 or PCC 1:2:4 type B0, complete all as specified and as directed including taking down old unserviceable sink with fittings. |
| 94 | S&F in repairs corrosion resistant Stainless Steel Kitchen plate rack of size 31x30x10 inch, with 0.80 mm thick Stainless Steel sheet (min weight 7.00 Kg) fixed to walls with rawl plug and brass screws, complete all as specified and as directed.Make: Prayag Cat No. P-346 or equivalent in makes mentioned in Appendix \"B\" here-in-after. |
| 95 | Cleaning and removing all scale and dirt, etc, from tanks of capacity exceeding 250 ltrs and not exceeding 500 ltrs and from mouths of circulating pipes, etc. complete all as specified and as directed. |
| 96 | Cleaning and removing all scale and dirt, etc, from tanks of capacity exceeding 500 ltrs and not exceeding 1000 ltrs and from mouths of circulating pipes, etc. complete all as specified and as directed. |
| 97 | Dismantling of existing any type & any capacity water storage tank fixed in any description andS&F new 2000 litres capacity (white colour) rotational moulded polythene water storage tank, (cylindrical verticalwith close top) triple layer colour white both inside and outside with top cover hoisted and fixed in position where ordered and making necessary connections for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I and as directed. |
| 98 | Dismantling of existing any type & any capacity water storage tank fixed in any description andS&F new 1000 litres capacity (white colour) rotational moulded polythene water storage tank, (cylindrical verticalwith close top) triple layer colour white both inside and outside with top cover hoisted and fixed in position where ordered and making necessary connections for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I and as directed. |
| 99 | Dismantling of existing any type & any capacity water storage tank fixed in any description andS&F new 500 litres capacity (white colour) rotational moulded polythene water storage tank, (cylindrical verticalwith close top) triple layer colour white both inside and outside with top cover hoisted and fixed in position where ordered and making necessary connections for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I and as directed. |
