|
| 1 | Dismantling single layer Mangalore pattern or similar tiles in roofing complete all as specified and directed. |
| 2 | Dismantling wooden battens for tiles, shingles etc, of any size including tilting fillets, spaced exceeding 15 cm complete all as specified and directed. |
| 3 | Dismantling timber scantlings 40 sq. cm and over in section, in unframed work, in any position complete all as specified and directed. |
| 4 | M&L for second class hardwood in scantlings, clean sawn, timber framed, as in rafters and purlins, etc without finish complete all as specified and directed. |
| 5 | S&F rolled mild steel structural work in rectangular/ tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S.1161- 1979 grade St.-240 complete all as specified and directed. |
| 6 | M&L preparation of new surfaces of steel and iron work of any description over 10 cm width or girth with applying two coats of synthetic enamel paint over one coat of red oxide zinc chrome primer etc complete all as specified and directed. |
| 7 | S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 8 | S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 9 | M&L for preparing surfaces of wood and wood based materials, new or old, of any description and girth, not otherwise described and treated with two coats of creosote oil complete all as specified and directed. |
| 10 | M&L for aluminium wind tie of any size fixed with self tapping screws of size 50/ 75 mm with integral EPDM washer in roof covering complete all as specified and directed. |
| 11 | Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and directed. |
| 12 | M&L for aluminium concealed frame work 1200 x 600 mm size and 6 mm thick PVC hollow false ceiling board including 4 mm dia G.I. wire hanger to fix the frame work with RCC slab/ truss complete all as specified and directed. |
| 13 | Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing) and remove rubbish off the premises complete all as specified and as directed. |
| 14 | M&L for non-skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, including 15mm thick cement mortar as screed bed in CM 1:4 set and jointed and pointed in white or coloured cement to match complete all as specified and directed. |
| 15 | M&L for glazed ceramic coloured tiles on vertical surfaces 350x 250x 7 mm/ 450x 350x 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match, including 10mm thick cement mortar as backing coat in CM 1:4 set and jointed and pointed in white or coloured cement to match complete all as specified and directed. |
| 16 | Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, and removing the debris from the premises upto 1 KM from the defence area complete all as specified and directed. |
| 17 | M&L for providing pre-cast cement concrete block masonry with solid blocks, exceeding 10cm in width with PCC (1:3:6), type C1, using 20mm graded stone aggregate and set in cement mortar (1:6) complete all as specified and directed. |
| 18 | M&L for rendering 10mm thick in cement mortar (1:6) on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed. |
| 19 | M&L for providing and applying 1mm thick plaster of Paris putty over plastered surface to prepare the surface even and smooth and applying two coats of distemper oil emulsion over a coat of primer, preparatory to distempering complete all as specified and directed. |
| 20 | Taking down chowkats with shutters any description not exceeding 1.5 Sqm each (without taking off shutters from the frame) complete all as specified and directed. |
| 21 | Taking down chowkats with shutters any description exceeding 1.5 Sqm but not exceeding 4 Sqm each (without taking off shutters from the frame) complete all as specified and directed. |
| 22 | M&L for factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 50 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately).Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 23 | M&L for factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 35mm thickness comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.(Note: stainless steel butt hinges and necessary S S screws shall be paid separately) |
| 24 | S&F 125 mm size stainless steel butt hinges, medium weight complete all as specified and directed. |
| 25 | S&F 150 mm (length of bolt) aluminium anodised, barrel tower bolts of extruded section complete all as specified and directed. |
| 26 | S&F 150 mm size extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed. |
| 27 | S&F 250 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all as specified and directed. |
| 28 | S&F aluminium (extruded section) body door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed. |
| 29 | M&L for powder coated aluminium sliding window shutters with styles 40 mm x 20 mm, sheet thickness 1.20 mm two shutters of glass and one shutter of wire mesh consisting of stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples, frame (chowkat) of window shall 91.80 mm x 31.75 mm x 1.20 mm thick section for glass shutter (three track) with or without rebate 5 mm thick tinted glass fixed with aluminium beads locking arrangement with each shutter complete all as specified and directed. |
| 30 | M&L for providing powder coated aluminium door (coating of any colour) using aluminium section weighing not less than 0.55 Kg/ Rm for frame and door shutters including necessary joining cleat, glazing clips, rubber neoprene packing, handle 2 Nos per shutter, hinges, aluminium anodised with sash bars, anodised snap beads, screws and fixed along with 8 mm thickness glass fixed with glazing clips, shutters fixed on frame etc (the rate inclusive of all fixing of builders hardwares such as hinges, vow handles, locking arrangements etc complete all as specified and directed. |
| 31 | M&L for powder coated aluminium grill with 4 mm thickness designed as per type DG-902 mentioned in SHT No. 1/1 of drawing No. CE/CZ/TD-531 complete all as specified and directed. |
| 32 | M&L for 3 mm thick ACP (Aluminium composite panel) with UV protection as per design including aluminium frame work, including silicon for fixing sheet and filling joints complete all as specified and directed. |
| 33 | M&L for complete removal of existing treatment on wall surfaces and applying one coat of wall primer (water thinnable/ solvent thinnable), 3 mm thickness wall care putty over plastered surface to prepare the surface even and smooth, applying one coat priming with alkali resistant priming paint and applying two coats of distemper oil emulsion to be applied by approved applicator of the manufracturer of the paint complete all as specified and directed. |
| 34 | Taking up or down 15 mm bore steel/ CPVC/ UPVC tubing and connections, including cleaning for refixing or removal to store complete all as specified and directed. |
| 35 | Taking up or down 20 mm bore steel/ CPVC/ UPVC tubing and connections, including cleaning for refixing or removal to store complete all as specified and directed. |
| 36 | Supplying and laying of 20 mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls or laying in trenches complete all as specified and directed. |
| 37 | Supplying and laying of 25 mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls or laying in trenches complete all as specified and directed. |
| 38 | S&F in repairs stop valve, cast copper alloy, chromium plated, fancy type with long shank and cup (concealed type), screwed down, high pressure, with crutch or butterfly handle, screwed both ends for unions or fixed for 15mm bore dia of pipe complete all as specified and directed. |
| 39 | S&F in repairs angular cock, cast copper alloy, chromium plated, fancy type, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for unions or fixed for 15mm bore dia of pipe complete all as specified and directed. |
| 40 | S&F in repairs brass chromium plated mixer for mixing hot and cold water screwed down for 15mm bore dia. iron pipe complete all as specified and directed. |
| 41 | S&F in repairs PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed. |
| 42 | S&F in repairs SS grating 100 mm dia complete all as specified and directed. |
| 43 | Taking down shutters of any description exceeding 2 sq.m each and refixing in other opening by making good complete all as specified and directed. |
| 44 | Dismantling water tanks exceeding 250 ltrs and not exceeding 500 ltrs capacity and removing to store complete all as specified and directed. |
| 45 | S&F Rotational moulded polyethylene water storage tanks 1000 ltrs capacity(cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including Ball valve 20 mm bore dia high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 20 mm - 210 gms) complete all as specified and directed. |
| 46 | M&L for point wiring complete for one light point controlled by one switch with 1.5 sqmm single core PVC insulated unsheathed FRLS cable 1100 volts grade with multi stranded, copper conductor partly concealed in wall through PVC conduit and conduit accessories and partly surface on ceiling/ roof through PVC conduit and accessories of suitable size with modular metal flush boxes of suitable size & modules, concealed in walls with modular white plated cover as top cover fixed with screws for housing switches, socket outlets, fan regulators etc, multistranded single core green colour copper conductor for earth continuity connected to earth dolly, including taking down old point wiring complete all as specified and directed.Note: Cost of modular metal flush boxes concealed in wall with suitable white cover plate for mounting switches/ sockets, regulators, bell push etc and cost of cutting chases & making good to disturbed surface with cement mortar, if required any shall be deemed to be included in the quoted rate. |
| 47 | All as per item No. 46.00 here in before, but for one ceiling/ exhaust fan point controlled by one way switch and regulator, including taking down old point wiring complete all as specified and directed. |
| 48 | All as per item No. 46.00 here in before, but for one 2/ 3 Pin, 5 Amps socket outlet on independent board, including taking down old point wiring complete all as specified and directed. |
| 49 | All as per item No. 46.00 here in before, but for one 2/ 3 Pin, 5 Ampssocket outlet on same board with other switches/ sockets, including taking down old point wiring complete all as specified and directed. |
| 50 | All as per SI item No. 46.00 here-in-before, but for one switch socket outlet, 3 pin 16 Amp on independent board with 2.50 Sqmm FRLS cable and 2.50 sqmm cable earth continuity wire, including taking down old point wiring complete all as specified and directed. |
| 51 | All as per SI item No. 46.00 here-in-before, but for one switch socket outlet, 3 pin 16 Amp on independent board with 4.00 Sqmm FRLS cable and 4.00 sqmm cable earth continuity wire, including taking down old point wiring complete all as specified and directed. |
| 52 | S&F modular switch 1 way 6A, 1 module, 240 Volts complete all as specified and directed. |
| 53 | S&F modular socket, 6A - 2/3 pin combined 2 module, flush type complete all as specified and directed. |
| 54 | S&F modular switch 1 way 16A, 1 module, 240 Volts complete all as specified and directed. |
| 55 | S&F modular socket 6A/16A - 2/3 pin combined 2 module, flush type complete all as specified and directed. |
| 56 | S&F ceiling rose, 3 terminals PVC/ polycarbonate, isolated body complete all as specified and directed. |
| 57 | S&F modular fan step regulator, 120W - 2 module, 240 Volts, 50 Hz complete all as specified and directed. |
| 58 | S&F Recessed/ Surface mounting 22 Watts LED luminaire, prewired with white powder coated CRCA housing with LEDs and fully window acrylic diffuser, suitable for 150x150mm E-grid/ POP/ false ceiling complete with all accessories making connection using 3 core, 0.50 Sqmm PVC insulated and overall sheathed flexible copper conductor cable from ceiling rose/ PVC connector to light fitting and testing etc complete all as specified and directed. |
| 59 | S&F LED batten extruded aluminium body with PC diffuser in unique square shape >120 degree wide distribution, 4 feet 20 watts of minimum efficacy 120 lumen/ watts LED batten 4 feet 20 watts, CCT 6500 K complete including connection upto ceiling rose with flexible copper twin twisted wire including taking down old unserviceable light fitting complete all as specified and directed. |
| 60 | S&F LED batten extruded aluminium body with PC diffuser in unique square shape >120 degree wide distribution, 2 feet 10 watts of minimum efficacy 120 lumen/ watts LED batten 2 feet 10 watts, CCT 6500 K complete including connection upto ceiling rose with flexible copper twin twisted wire including taking down old unserviceable light fitting complete all as specified and directed. |
| 61 | S&F in replacement submain wiring with using two single core 6.0 Sqmm copper multi-stranded conductor PVC insulated and unsheathed (FRLS) cable and one single core 6.0 Sqmm copper multi-stranded conductor PVC insulated and unsheathed (FRLS) Earth wire using ISI Marked IS 694 1100 volts grade PVC insulated flexible stranded copper conductor wire drawn through with and including medium grade concealed PVC conduit ISI marked not less than 25 mm dia including conduit fitting and accessories complete including cutting chases in existing wall of any description built in cement mortar and making good the disturbed surfaces in cement mortar (1:4) and finishing the surfaces to match with existing surfaces and finish termination with bottle type copper lugs conduitbeing laid either in ceiling slab or wall or on surfaces or under the frame of the false ceiling including PVC flexible conduit or through wooden partition including clamping arrangementas required complete all as specified and directed .Note:- Two Run of 6.0 Sqmm cable and one run of 6.0 sqmm earth wire in and including conduit of suitable size shall be measured as one unit. |
| 62 | S&F in repairs MCB SP 6-32Amps breaking capacity 10 KA\"B\" series 240 volts 50 Hz complete all as specified and directed. |
| 63 | S&F in repairs RCBO for earth leakage, overload & short- circuit protection Double pole, 300mA, 40-63 Amps complete all as specified and directed. |
| 64 | S&F in repairs of MCB TPN 63 Amps breaking capacity 10 KA\"B\" series 415 volts 50 Hz complete all as specified and directed. |
| 65 | S&F new sheet metal enclosure single pole and neutralwith a two pin and earth plug and socket complete with one double pole MCB of 20 Amp, 240 Volt including taking down old unserviceable sheet metal enlosure complete all as specified and as directed. |
| 66 | S&F in replacement of double door MCB SPN distribution board with steel sheet powder coated DB 8 Ways with 200 amps rated bus bar suitable for MCB fitted with bus bar neutral link earth bar and din rail single phase 240 volts and neutral confirms to IS 13032- 1991 complete including and making good the disturbed surfaces of walls, floors filling up of holes, plastering, white washing/ distempering etc matching to the existing all as specified and directed. |
| 67 | S&Fin replacement of double door MCB TPN distribution board with steel sheet powder coated DB 4 Ways with 200 amps rated bus bar suitable for MCB fitted with bus bar neutral link earth bar and din rail single phase 415 volts and neutral confirms to IS 13032- 1991 complete including and making good the disturbed surfaces of walls, floors filling up of holes, plastering, whitewashing/ distempering etc matching to the existing complete all as specified and directed. |
| 68 | S&F LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete with 01 No. bracket of suitable size and cable including taking down old unserviceable street light fitting complete all as specified and directed. |
| 69 | Taking down fan (ceiling/ exhaust), sealing cable end, dismantling blades and removing fan and blades, deposited to MES store yard complete all as specified and directed. |
| 70 | S&F ceiling fan complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC without remote) complete all as specified and directed. |
| 71 | S&F BEE five star rated exhaust fan, steel body AC single Phase, 230V of size 300mm sweep with blades, frame and louvers and all mounting accessories, including making exhaust venthole on wall of toiletand suitable length of twin twisted flexible copper wire of size 40/0.0076 Sqmm from ceiling rose to fan connector and all connecting accessories complete all as specified and directed. |
| 72 | S&F electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc. complete all as specified and directed. |
| 73 | M&L for Earthing complete with using GI earth plate electrode 600x600x6.0 mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below ground level) with top edge of the plate not less than 1.5 mtr below normal ground level and earth plate surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness off 15 cm all around the plate with using 4 mm dia GI Wire as earth lead moulded and retrieved to earth plate at one end and connected to main switch / control board at another end with and including 15 mm dia GI light grade from upper end of earth plateupto external faceof the wall of the building including 20 mm dia bore GI pipe light grade as water pipe from chamber to upper edge of the plate GI funnel with wire mesh fixed on water pipe and provision of PCC 1:2:4 type B-1 (Using 20 mm Dia graded stone aggregate) duly reinforced with mild steel round bar 6 mm dia@ 150 mm c/c both ways with 10 mm dia mild steel bars as in liftinghandle with and including necessary excavation and earth work including laying the pipe concealed in floor / wall all as per plate No-3 of SSR Part-I complete all as specified and directed and testing on completion including taking down old unserviceable earthing complete. (Note:- If the desired resistance is not found earthing shall be re-done by the contractor at no extra cost to Govt) complete all as specified and directed. |
| 74 | Excavating in trenches in hard/ dense soil, not exceeding 1.5 m wide and not exceeding 1.5 m in depth; for laying cables, pipes, etc. not exceeding 10 sq m on plan and not exceeding 1.5 m in depth and getting out complete all as specified and directed. |
| 75 | Returning filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm using soil obtained from excavation complete all as specified and directed. |
| 76 | Removing excavated soil material from site to a distance not exceeding 50 mtr away and depositing where directed at a level not exceeding 1.5 mtr from the starting point complete all as specified and directed. |
| 77 | M&L for sand cushioning to under ground cable 8 cm thick before laying the cable and 15 cm thick after laying complete all as specified and directed. |
| 78 | M&L for bricks; common burnt clay building old size bricks sub-class ‘B’ Designation 75 complete all as specified and directed. |
| 79 | M&L for laying XLPE insulated, PVC innersheathed, extruded PVC outer sheathed, LT underground cable, armoured with glavanised steel strip, heavy duty electric cable with stranded aluminium conductor of cross-sectional area 3.5 core 35 sqmm, 1100 volts grade, as per IS 7098 (Part 1) 1988, laid in trench, fixed on wall/pole drawn through pipe etc includingof provision of lugs & testing, including taking down old LT UG cable complete all as specified and directed |
| 80 | M&L for 50 mm bore GI tubing light grade with fittings laid for protection of cable under road crossing, fixed to walls or pole complete all as specified and directed. |
| 81 | S&F 25 mm external dia. rigid non-metallic PVC conduit exclusive of boxes (junction/ terminal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc. complete all as specified and directed. |
| 82 | S&F junction boxes (1 to 4 way) of external dia 25 mm complete all as specified and directed. |
| 83 | S&F telephone socket (RJ-11) complete all as specified and directed. |
| 84 | S&F TV socket complete all as specified and directed. |
| 85 | Repair to potholes any depth, not exceeding 1 Sq m each including sweeping free from dust and mud, or water, scoring sunken surfaces in roads, paths, etc. cutting around edges to at least 25 mm in depth, making good by filling in screened & graded road metal, watering and well ramming (including supply of road metal) complete all as specified and directed. |
| 86 | M&L for applying evenly a priming/ tack coat with bituminous primer at 10 Kgs per 10 sq metre using paving bitumen complete all as specified and directed. |
| 87 | M&L for preparing unsurfaced water bound macadam surfaces by brushing with wirebrushes for removing caked mud etc. sweeping with brooms and finally fanning thecleaned surface with gunny bags to remove all loose dirt etc. and applying evenly a priming/ tack coat with bituminous primer using VG-10grade at 5 Kgs per 10 sq metre using paving bitumen complete all as specified and directed. |
| 88 | M&L for bituminous premix semi-dense asphaltic concrete (design mix) 40mm consolidated thickness with 5.5% binder content using paving bitumen VG-30 by weight of total mix, rolled and compacted to required camber and gradient using mechanical paver and rolled with 8 to 12 tonne capacity power roller complete all as specified and directed. |
| 89 | M&L for preparing bituminous surfaces of road and marking 2.5mm thick centre lines, stop lines, dashes, arrows etc. and the like not exc. 10cmwide on roads pavements with hot applied thermo plastic road marking paint of approved colour confirming to BS 3262-1989 with special applicator machine all as per manufacturers instruction complete all as specified and directed. |
