|
| 1 | NOTE: Schedule ‘A’ Part - ItoPart - IXare Prepriced by MES. Bidders shall insert their lumpsum amount in the Green coloured field under Col-6 only. |
| 2 | Total amount of Sch \"A\" Part - I(BUILDING Works) |
| 3 | Total amount of Sch \"A\" Part - II (SITE CLEARANCE WORKS) |
| 4 | Total amount of Sch ‘A’ Part - III (INTERNAL ELECTRIC SUPPLY)) |
| 5 | Total amount of Sch ‘A’ Part - IV (PROTECTIVEWORKS) |
| 6 | Total amount of Sch ‘A’ Part - V (ROAD, PATH. HARDSTANDING & CULVERTSWORKS) |
| 7 | Total amount of Sch ‘A’ Part - VI (AREA DRAINAGE) |
| 8 | Total amount of Sch \"A\" Part - VII(EXTERNALELECTRIC SUPPLY WORKS) |
| 9 | Total amount of Sch ‘A’ Part -VIII ( EXTRNAL WATER SUPPLY WORKS) |
| 10 | Total amount of Sch ‘A’ Part - IX (LIGHTENING PROTECTION) |
| 11 | SCH \"A PART - X(Miscellaneous B/R and E/M works for Sch \"A\" Part-II to Part-X)Note: This schedule is not pre-priced by MES and the rate indicated as \"Rs 0.00\" under Col 5 signifies this fact only |
| 12 | Supply and fixing, steet metal enclosure powder coated Single phase flame proof DB with 200 Amps rated bus bar 240 V, SPN 8 ways LM6 of size 400 x400 x125 mm for fixing MCBs.C complete all as specified and directed. |
| 13 | Supply and fixing,Fire Alarm control panel complying with BS EN 54 Single loop panel of capacity from 30 detectors and 30 Modules complete all as specified and directed. |
| 14 | M&L forpolyethene film, black 125 micron laid in floor over sand cushioning for laying pavement quality concrete, complete all as specified and directed. |
| 15 | Supply, Install Testing & Commissioning ofself supportingtotally enclosed double door at front, LT feeder piller compartmentalised design, dust and varmin proof of size 600 mm(Height) x 600 mm(Length) x 450 mm(Width)suitable for 440 Volt 3 phase 4 wire system made out of 3.15 mm thick CRCA sheet and built upon regid frame work having front and rear hinged doors with neoprence rubber gasket including danger plate, earthing strip point and, ventilation louvers at the rear side, bottom detachable gland plate complete with suitable size of Zinc/Cromium plated and nuts, bolts ;and washers etc. The pannel shall be synthetic enamelled paintedand the control circuit diagram shall bewith colour code solid conductorcopper 1.5 sqmm cable for easy identification including incomming/outgoing cable holes at the bottom, complete after taking down the old unserviceable one.The Panelshall be emmbeded with 75 x 6 mm MS Angle Iron frame and to be grouted with PCC foundation (1:2:4 )type B2 upto a height of 50 cm from normal ground level complete all as specified and directed by Engr in charge and comprising of the following.(For Motor) complete all as specified and directed. |
| 16 | (a) Aluminium bus bar 100 amps - 04 Nos, supported with suitable size of heavy duty porcelin stand lock with suitable sizeof brass nut, bolts and washer with heat shrinkable PVC sleeving.The bar shall be colour coded (red, yellow and blue) for three phases and black for neutral.(b)MCB of SPN, 32 A, 10 KA, with breaking capacity of 25 KA, (c)MCB of SP,20 A, 10 KA,Make : L & T/Havells - 5 No(4 Motor and 1Stand By)(Outgoing)INDICATING DEVICES(a) LED Indicating lamps for Main Supplyindicating R\", Y\" B\"- 01 Set of 3(b) Digital Voltmeter (Make AE/L&T) - 01 No(c)Current Transformer havingRatio 400/5, 15 VA- 01 Set of 3(d) Digital Ammeter ( Make(AE/L&T) - 01 N0(d) Digital Ammeter ( Make(AE/L&T) - 01 N0 |
| 17 | Supply and fixing junction box made out of 3.15 mm thick MS sheet powdered coated with locking arrangment of size (30 cm x 15 cm x 8 cm) including 01 No 6 Amp SP MCB, 2 Nos bus bar of suitable size with suitable number of holes fixed on Street light pole with suitable MS clamps all as specified and directed . |
| 18 | M&L for Elestometric Nytral rubber insulation to PP-R pipes suitable for 40mm outer dia 28/19mm thick with chiken wire mesh wire netting 25mm gauge, 20mm mesh with 0.01mm aluminium foil including jointing and fixing material such as solvent adhesive SR-998 complete all as specified and directed . |
