|
| 1 | Dismantling aluminum/ Gypsum partitions, doors, windows, fixed glazing and false ceiling and its aluminum frame work including disposal of unserviceable material and stacking of serviceable material within 250 meters lead and 10 m lift as directed by Engineer-in-charge. |
| 2 | Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material and safely handing over to the civil department as directed by engineer-in-charge:GI/Profile Sheets |
| 3 | Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc., including dismembering and stacking within 50 metres lead |
| 4 | Supply & fixing Structural steel workin single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applyinga priming coat of approved steel primer all complete. |
| 5 | Providing and fixing Minimum 1 hr fire rated Single/ double leaf door of required size of G.I 1.2mm frame and 0.8 GI shutters with infill material of Honey comb, frame profile 100mm x 57mmwith hardware set of 3 Ball bearing butt hinges, CE4330, SS304 of size 100 x 75 x 3mm with screws in SSS, Mortise dead lock H4 Bs 55 sss, cylinder 70mm 5 pin BSKO Brass, Pull handle D back to back 19x250 mm SS, clear fire rated, 6mm, for 120 mints of size 200 x 300mm,2no Gasketfire rated, 4mm thick x 13mm, Black , Door closer with standard arm, silver finish- Ryobi, single /Doubleof approved brand complete as per the instructions of EIC |
| 6 | Providing and fixing 0.5mm thick precoated colour galvalume profile sheets (size,shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with AZ150 GSMas per IS14246, IS: 277, in 550 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required & all necessary fixing accessories. |
| 7 | Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to all/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer\"s specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks). |
| 8 | Providing & Fixing of 2mm thick PVC flooring using full length sheets. Make: Poly floor mottled finish, including cost of adhesive of approved quality including surface preparation and neatly jointed finish complete. |
| 9 | Providing & fixing toughened glass 12 mm thickness with aluminium/steelbeading around glazing in partitions including cost of cutting to shape, fixing wastage at all heights & levels, drilling holes, providing silicon etc to complete; as per EIC. |
| 10 | Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineerin- charge. Pre-laminated particle board with decorative lamination on both sides. |
| 11 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 12 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water thinnable priming coat with cement primer |
| 13 | Providing & Painting synthetic enamel paint with two or more coats on Steel structures including surface preparation. |
