|
| 1 | Demolition ofPCC in Ground Floor and paving n exc 15 cm (below or above ground level) |
| 2 | Dismantaling Stone slabs and tiles of any description or thickness in floors, aprons etc. |
| 3 | M&L for PCC type D2 1:4:8 using 40mm graded stone aggregate, 75 mm thick as in sub base for floors, complete all as specified and directed. |
| 4 | M&Lfor machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over and including screed bed or bedding layer of 15 mm thick in CM (1:6) all as specified and directed by Engineer-in-charge. |
| 5 | M&Lfor Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar and laid over cement screed and jointed with pigment to match the shade of the slab including rubbing and polishing complete over and including 10 mm thick backing coat in CM (1:4) complete all as directed by Engineer-in-charge. |
| 6 | M&L 25 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite.and black |
| 7 | M&L for 5cm sand stone slabs in sunshades, chajjas, shelves, cills, landings, cover stones, templates etc, n exc. 2m in length, punched dressed on face and along exposed edges, self faced on other side and set and pointed in lime mortar 1:2 or cement mortar 1:4, complete complete all as specified and as directed by the Engineer-in-Charge |
| 8 | M&L for 50 mm thick PCC 1:3:6 type C1 as in plinth protection incl surface finished even and smooth w.using extra cement as specified and directed by Engr in Charge.. |
| 9 | Complete removal of existing water proofing treatment incl bedding if any n exc. 50mm thick etc. on any type of roof, cleaning with wire brushers etc. and removal of debris out side MD land complete all as specified and directed. |
| 10 | M&L for PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate for levelling course for consolidated thickness shall be varied from 25 to 55 mm as per the requirements all as directed by Engr-in-Charge. |
| 11 | M&L for 10mm thick screed plaster on roof for laying in CM 1:4 waterproofing treatment, with using WPC (WPC will be measured and paid separately as supply only) |
| 12 | Supply only integral Waterproofing compound. |
| 13 | M&L for APP based polymeric membrane minimum weighing 3 Kg/Sqm and minimum 3mm thick reinforced with polyester non wove fabric (wt not less than 150 gms/sqm) laid over primed surface including bituminous primer conforming to IS-3384 applied @ 0.3 Ltr/Sqm by forcedall as specified and as directed , Four course roof treatment consist of as under :- (i)Applying one coat of bituminous primer conforming to IS-3384 @0.3 Ltr per sqm, (ii)Laying of APP based membrane as specified thickness and weight, (iii)Applying one coat of aluminium paint @ 100 ml/sqm |
| 14 | Taking down cement plaster on stone walls and roof ceilings etc., including racking out joints, hacking for key, scrubbing down with water etc. to receive new plaster |
| 15 | M & L for Cement plastering 15mm( thick in two layers -first layer 10mm thick with ready mix plaster and outer layer 5mm thick ready mix water proof plaster) on outer walls by adding potable water by weight of material as mentioned by manufacture ready mix plaster shall comply with IS- 1661-1972, IS-2402-1963, IS- 2250-1981 and shall confirm 28 days compressive strength 10-15 MPA, bulk density 1600-1800 kg/cum and pull out bond strength->0.5 MPA complete all as specified and directed |
| 16 | M & L forrendering 10mm thick ready mix plaster on internal wall by adding potable water by weight of material as mentioned by manufacture ready mix plaster shall comply with IS- 1661-1972, IS-2402-1963, IS-2250-1981 and shall confirm 28 compressive days cstrength 10-15 MPA bulk dencity 1600-1800 kg/cum and pull out bond strength-> 0.5 MPA omplete all as specified and directed. |
| 17 | M & L forrendering 5 mm thick ready mix self curingplaster on ceilling by adding potable water by weight of material as mentioned by manufacture ready mix plaster shall comply with IS- 1661-1972, IS-2402-1963, IS-2250-1981 and shall confirm 28 compressive days cstrength 10-15 MPA bulk dencity 1600-1800 kg/cum and pull out bond strength-> 0.5 MPA omplete all as specified and directed. |
| 18 | M&L for preparation of new plastered surface of wall andapplyingTwo coat of oil bound distemper over the alkali resistance priming paint primer over 1.5 to 2mm thick wall care puttycomplete all as specified and as directed. |
| 19 | M&L for preparing newly plastered surfaces of walls and applying two coats of cement base paint over a coat of alkali resistance primer complete all as specified. |
| 20 | M&L preparation of new wall surface and applying three coat of white wash on surfaces of ceiling complete all as specified & directed by Engineer-in-charge. |
| 21 | Taking down door chowket or frame incl shutter area n exc 1.50 sqm each and removing to store. |
| 22 | Taking down chowkhat or frame existing doors/windows/ventilators (without taking off shutters and guard bars) of exe 1.5 sqm & n. exc 4 sqm etc complete all as specified and as directed incl stacking the materials properly. |
| 23 | Providing and fixing powder coated 50 microns extruded aluminium in 3 Tier Track Sliding Windows/glazing, with frame of section 100x44-45x1.30mm, track of size 100x38.10x1.30 & shutters made of size 32x18x1.3mm, with and including 4mm thick tinted sheet glass selected quality fixed in 2 shutters and stainless steel wire gauge 0.36mm nominal dia of wire and average width of aperture 1.40mm in one shutter and including EPDM gasket to render the glazing, air and water tight etc. & aluminium beeds 20mm size and also including powder coated 150mm handle with built in locking system for each leaf complete all as specified. |
| 24 | S & F Factory made ISI marked flush door shutters 35mm thick, BWP conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 2nd class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters complete all as specified and including supply and fixing following items As approved by Accepting Officer :(a) Stainless Steel (304 Grade) Finished Butt Hinges 125mm -4 Nos per leaf(b) Stainless Steel (304 Grade) Finished Tower Bolt 200mm long - 2 Nos per leaf(c) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 Nos per leaf(d) Stainless Steel (304 Grade) Finished Sliding Door Bolt/Aldrop 16 x 300mm- 1 No per leaf(e) Stainless Steel (304 Grade) Finished Floor Door Stooper- 1 No per leaf |
| 25 | S&F in repair aluminium anodised, (fancy type)curtain rod, 20mm dia, complete all as specified and as directed. |
| 26 | Preparation of new wooden surfaces of any description, nototherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and direction. |
| 27 | Preparation of new Steel surfaces of any description, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and direction. |
| 28 | Providing and placing in position microconcrete which shall be cement based prepacked single component, chloride free, non-shrink, free flow, self compacting, ready to use after mixing water in specified proportion obtained from approved manufacturer of thermoex chemical as per speciification and direcation of engineer-in-charge (payment under this item shall be made only after wet curing bas been done and surface has been satisfactory evaluated by sounding/tapping with blunt metal instrument). |
| 29 | Taking down carefully existing point wiring of any description light, fan,sockets,bells etc) complete including fittings such as terminal boxes, switches, sockets, ceiling rose, lamp holders, brackets sketch fittings, pendants, fan regulartors and making good the disturbed surfaces, walls, floors etc. all as directed by EIC |
| 30 | Taking down old unsv GI earthing |
| 31 | Taking down old unsv MCB DB / main switch incl MCBs / MCCBs complete all as specified and directed |
| 32 | Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc. for stone concrete block or slab walls and making good, cutting exceeding 20cm girth |
| 33 | M&L point wiring complete with 1.5 Sqmm single core PVC insulated FRLS cable 1100 Volts grade multistranded copper conductor drawn through in PVC Conduit concealed on underground stone / brick, masonry walls, roofs floors etc including MS terminal boxes fabricaterd out of 1.12mm thick MS sheet sunk type / surface type and laminated top sheet of 2mm thick for housing switches sockets, regulators etc including provn of 1.5 sqmm dia copper conductor for earth wire connected to common dolly for One light point / Fan point / Exhuast Fan / Bell point controlled by one 5 Amps One way switch and making good surfaces all as specified and directed by Engineer-in-Charge. |
| 34 | All as per Item No. 05 but for one 3 pin 5/6 Amps switch socket outlet on same board |
| 35 | All as per Item No. 05 but for one 3 pin 5/6 Amps switch socket outlet on independent board |
| 36 | All as per item No. 05 above but wiring with 4.0 Sq mm and 4.0 sqmmfor earth continuity for 3 pin 15/16 Amps switch socket combination |
| 37 | M&L switch piano flush type single pole one way 5 Amps complete all as specified and directed. |
| 38 | M&L switch piano flush type single pole one way 15 Amps complete all as specified and directed. |
| 39 | M&L Switch Socket Combination outlet, multipurpose, 2 pin 5 amps/3 pin 5 amps controled by one switch 5 amps, flush type complete all as specified and directed. |
| 40 | M&L Universal socket outlet with shutter, 5/15 amps controlled by one switch 15 amps, flush type complete all as specified and directed. |
| 41 | S&F Electronic type Modular fan step regulator 120W, 2 module AC 240 V all as specified and directed |
| 42 | M&L lamp holder insulated body with back plate suitable for battern fittings |
| 43 | supply and fix LED Lamp Retro fit type 9 watts 230 V and all as specified by Engr-in-charge |
| 44 | S&F Ceiling rose surface bakelite 65 x 50 mm 2/3 terminais all as specified |
| 45 | S&F Sheet Modular metal enclosure DB SPN 240 Volts 12 Way single door type with 200 Amps busbar for fixing of MCBs |
| 46 | S&F MCB Single pole and neutral, 40A, 240 Volts AC all as specified |
| 47 | S&F MCB Single pole, 5-32A, 240 Volts AC all as specified |
| 48 | M&L Earthing complete with galvanized steelearth plate electrode 60cmx60cmx6mm thick buried directly in ground (earth pit not less than 2.25 mtr below ground level) with top edge o the plate not less1.5 mtrs below normal ground level connected to galvanised earth lead wire 4 mm dia by means of bolts nuts, check nuts and washers of galvanized iron of steel all as shown in electrical plate No.5 connected to earthing test point incl necessary earth work, excavation PCC 1:3:6 type CI using 20mm graded stone aggregate for earth chamber provn of PCC cover 40 mm thick 1:2:4 mm type B1 funnel with water Pipe, GI pipe, 15mm dia medium grade protection pipe, GI earth lead all as specified |
| 49 | Supply and fixing LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete. |
| 50 | Supplying and fixing 1100 volts grade heavy duty cable PVC insulated aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspen ded by insulating hangers not more than 1 metre apart including4mm suspension wire, one twin core cable flat or circular of size 10 sqmm complete. |
| 51 | Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete. |
