|
| 1 | SCHEDULE‘A’ PART-I (Provision of waiting hut) |
| 2 | Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including disposal of excavated earth upto 50 m and lift upto 1.5 m, disposed soil to be levelled and neatly dressed. |
| 3 | Excavation work in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soils as directed, within a lead of 50 m in all kinds of soil. |
| 4 | Providing and laying in position cement concrete ofgrade 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size). |
| 5 | Providing and laying in position of reinforced cement concrete 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size), excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level. |
| 6 | Reinforced cement concrete 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) work in plinth andcolumns, excluding cost of centering, shuttering, finishing and reinforcement |
| 7 | Centering and shuttering including strutting, propping etc. and removal of form for foundations, footings, bases of columns, etc. for mass concrete. |
| 8 | Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers. |
| 9 | TMT bars steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. |
| 10 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in Cement mortar 1:6 (1 cement : 6 coarse sand). |
| 11 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level with cement mortar 1:4 (1 cement :4 coarse sand). |
| 12 | M/L 15 mm cement plaster on rough side of brick wall of mix 1:4 (1 cement: 4 fine sand). |
| 13 | 15 mm cement plaster on rough side of single or half brick wall finished with a floating coat of neat cement of mix 1:4 (1 cement: 4 fine sand). |
| 14 | Supplying, stacking, laying, spreading and compactingstone aggregate of 63 mm to 45 mm size to WBM specifications in uniform thickness, hand picking, rolling with 3 wheeled road / vibratory roller 8-10 tonne capacity in stages to proper grade and camber, applying and brooming requisite type of screening / binding material to fill up interstices of coarse aggregate, watering and compacting to the required density for hardcore. |
| 15 | Providing and laying cement corcrete of grade 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) in flooring. |
| 16 | Providing and laying 40 mm thick cement concrete pavement/flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size). |
| 17 | Providing and laying rectified Glazed Ceramic floor tiles of size 600x600 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse sand), including grouting the joints with white cement and matching pigments etc., complete. |
| 18 | Providing and laying non skid Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sq.m including pointing the joints with white cement and matching pigments etc., complete. |
| 19 | S & F anodised aluminium window with glazed andgauzed shutter sliding type using 1.80 mm thick aluminium open three track section having specific size of style, top and bottom rails, including anodised aluminium frame incl necessary joining cleats galzing clips rubber packing, anodized alumunium snap beading screws anodised aluminium fittings complete all as specified and as directed : Note : (S&F of 5 mm thick glass & stainless steel wire mesh are including in the items. No payment will be made separately). |
| 20 | Providing and fixing 35 mm thick factory made laminated veneer lumber door shutter conforming to IS : 14616 and TADS 15:2001 (Part B), including ISI marked M.S pressed butt hinges bright finished required size with necessary screws, all complete as pre directions of Engineer in charge and panelling with panels of 12 mm thick plain grade - 1, medium density flat pressed three layer particle board FPT -I or graded wood particle board FPTI, IS : 3087 marked, bonded with BWP type synthetic resin adhesive as per IS : 848. |
| 21 | Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-section, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. Fixing with carbon steel galvanised dash fastener of required dia and size (to be paid for separately). |
| 22 | Providing kiln seasoned and chemically treated hollock wood in frames of false ceiling, partitions etc. sawn and fixing in position |
| 23 | Providing and fixing 6 mm thick plain Multipurpose Cement board (High Pressure steam cured ) as per IS : 14862, with suitable screws for fibre cement board in ceiling etc. complete |
| 24 | Providing and fixing 2nd class teak wood lipping/ moulded beading or taj beading of size 18X5 mm fixed with wooden adhesive of approved quality and screws/ nails on the joint of ceiling board as per direction of Engineer-in-charge. |
| 25 | M & L framed work such as grills, gratings, etc. with ends of bars shouldered and/ or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con-forming to Fe.290.Gde-E-165 |
| 26 | Providing and fixing 4mm thick coir veneer board, ISI marked IS : 14842, plain lining with necessary screws, priming coat on unexposed surface etc. complete |
| 27 | Providing and fixing PVC rigid foam sheet 5 mm thick on existiing frame of (Bathroom and W C ) using synthetic rubber based adhesive or necessary screws etc. as required complete. |
| 28 | Providing flat iron brackets 50x3 mm size with necessary bolts, nuts and washers etc. for fixing asbestos cement/ GS sheets gutters with purlins. |
| 29 | Providing and fixing 25 mm wooden planking, tongued and grooved in flooring, eaves board including fixing with iron screws complete with second class deodar wood/ hollok wood. |
| 30 | Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 31 | Providing and fixing PVC Door Frame of size 50x47 mm with a wall thickness of 5 mm (± 0.2 mm), made out of single piece extruded PVC profile, with mitred cut joints and joint with 2 nos of PVC bracket of size 190 mm x 100 mm long arms of cross section size 35 x 15 mm & self driven self taping screws, the vertical door profiles to be reinforced with 40x20 mm M.S. rectangular tube of 0.8 mm and 3x hinges , including providing EPDM rubber gasket weather seal throughout the frame, including jointing 5 mm PVC frame strip with PVC solvent cement on the back of the profile. The door frame to be fixed to the wall using 8 x100 mm long anchor fasteners complete, all as per manufacturer\"s specification and direction of Engineer -in- charge. |
| 32 | 35 mm thick factory made solid panel PVC door shutter of single piece extruded profile decorative finished (wood grain finished) |
| 33 | Providing and fixing aluminium tower bolts150x10 mm, ISI marked, anodised (anodic coating not less than grade AC10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete |
| 34 | Providing and fixing aluminium handles 125 mm, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete. |
| 35 | Providing and fixing aluminium sliding door bolts 300x16 mm, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete. |
| 36 | Disempering with oil bound washable distemper of approved brand and manufacture to give an even shade on newwork (two or more coats) over and including water thinnable priming coat with cemen primer. |
| 37 | Steel work in built up tubular (round, square or rectangular hollow hollow tubes etc) trusses etc. including cutting, welding, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. |
| 38 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by engineer in charge 0.50 mm (+0.05%) total coated thickness with zinc coating 120 grams per sqm as per IS : 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both sideof the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches duriing transportation and should be supplied in single length upto 12 m ot as desiredby engineer in charge. the sheet shall be fixed using self drilling/ self tapping screws of size (5.5x55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surface, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 39 | Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05%) total coated thickness, Zinc coating 120 grams per sqm as per IS : 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete for ridges plain (500-600mm) |
| 40 | SCHEDULE \"A\" PART - II (SANITARY AND WATER SUPPLY) |
| 41 | Providing and fixing white vitreous china western type E.W.C. pan) with ISI marked white solid plastic seat and lid, 10 litre low level white P.V.C. flushing cistern, including Seat cover & flush pipe, with manually controlled device (handle lever), conforming to IS :231, with all fittings and fixtures complete, including cutting and making ood the walls and floors wherever required. |
| 42 | Providing and fixing White Vitreous China Wash basin size 630x450 mm with C.I. brackets and white vitreous china pedestal, a single 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require. |
| 43 | Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern withwith 5 litre white P.V.C. automatic flushing cistern, standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : |
| 44 | Providing and fixing 25 mm dia nominal bore G.I. pipes complete with G.I. fittings including trenching and refilling etc. |
| 45 | Providing and fixing 15 mm dia nominal bore G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. |
| 46 | Providing and fixing 15 mm nominal bore C.P. brass bib cock fancy typeof approved quality conforming to IS:8931. |
| 47 | Providing and fixing 15mm nominal bore C.P. brass angle valve fancy type for basin mixer and geyser points of approved quality conforming to IS:8931. |
| 48 | Providing and fixing 25 mm nominal bore gun metal gate valve with C.I. wheel of approved quality (screwed end). |
| 49 | Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet 150 mm diameter. |
| 50 | Providing and fixing C.P. brass stop cock 15 mm nominal bore (concealed) of standard design and of approved make conforming to IS:8931. |
| 51 | Providing and fixing600 mm long PTMT towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. |
| 52 | Providing and fixing PTMT soap Dish Holder having length of 138mm,breadth 102mm, height of 75mm with concealed fitting arrangements,weighing not less than 106 gms. |
| 53 | Providing and fixing mirror of superior glass (of approved quality) andof Rectangular shape 453x357 mm sizewith plastic moulded frame of approved make and shade with 6 mm thick hard board backing . |
| 54 | Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete. |
| 55 | Providing and fixing uplasticised PVC connection pipe, 15 mm nominal bore, 30 cm length with brass unions. |
| 56 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank 500 litre Capacity, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 57 | Providing and fixing 100 mm sand cast Iron grating for gully trap. |
| 58 | Flexible (coil shaped) PVC waste pipe for wash basin and urinal pot 32mm dia with length not less than 700 mm i/c PVC waste fittings |
| 59 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes 110 mm diameter, Single socketed pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. |
| 60 | Providing and fixing on wall face unplasticised - PVC moulded 110 mm bend for unplasticised Rigid PVCwater pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. |
| 61 | SCHEDULE \"A\" PART - III (ELECTRIFICATION) |
| 62 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with piano type switch, phenolic laminated sheet, suitable size M.S./PVC box and earthing the point with 1.5 sq.mm. FR PVC insulated copper conductor single core cable etc as required. (group B wiring) |
| 63 | Wiring for light/ power plug with 2X4 sq. mm FR PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit along with 1 No 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required. |
| 64 | Supplying and fixing 3 pin 5/6 amp socket outlet on the existing switch box/ cover including connections etc. as required. |
| 65 | Supplying and fixing 5/6 amps switch piano type on the existing switch box/ cover including connections etc. as required. |
| 66 | Supplying and fixing 15/16 amp switch piano type on the existing switch box/ cover including connections etc. as required. |
| 67 | Supplying and fixing 6 pin 15/16 amp socket outlet piano type on the existing switch box/ cover including connections etc. as required. |
| 68 | Supplying and fixing brass/ insullated batten/ angle holder including connection etc. as required. |
| 69 | Supplying and fixing stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. |
| 70 | Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box/ wooden block includingconnection etc as required. |
| 71 | Supplying and fixing 2 + 6 way, Single door, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) |
| 72 | Supplying and fixing32 amps rating, 240/415 volts, \"C\" curve, miniature circuit breaker suitable for inductive load of single poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. |
| 73 | Supplying and fixing 63 amps rating, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. |
| 74 | Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required. |
| 75 | Supplying and drawing 2 x 6 sq. mm of FR PVC insulated copper conductor, single core cablefor service wire. |
| 76 | Supply, Installation, testing and commissioning of pre-wired, CFL bulkhead luminaires fitting with 9 watt CFL, with all accessories and tube etc. directly on ceiling/ wall, including connection with 1.5 sq. mm FR PVC insulated, copper conductor, single core cable and earthing etc. as required. |
| 77 | Supply, Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting suitable for surface/pendent mounting 1x36/40W FTL, with all accessories and tube etc. directly on ceiling/ wall, including connection with 1.5 sq. mm FR PVC insulated, copper conductor, single core cable and earthing etc. as required. |
| 78 | Supply, Installation, testing and commissioning of ceiling fan 1200 mm sweep, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FR PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required. |
| 79 | Supply, Installation, testing and commissioning of exhaust fan 380mm sweep including wiring the down rods of standard length (upto 30cm) with 1.5 sq. FR PVC insulated, copper conductor, single core cable including providing and fixing fouvers etc. as required. |
