Tender For Additional / Alternator Cum Special Repair To Jcos Or Md Accommodation At Dipatoli Mil Stn, Dipatoli-Jharkhand

TDR : 52872003

Tender Notice
BOQ

26 Days Left

Dipatoli , Jharkhand

Tender Brief : Tender For Additional / Alternator Cum Special Repair To Jcos Or Md Accommodation At Dipatoli Mil Stn

Document Fees
₹ 3000 /-

EMD
₹ 638050.0 /-

Tender Value
₹ 6.26 Crore /-

Submission Date
07-01-2026

Competition Type
Indian

Bidding Type
Tender

Need a Business Loan? Apply Now !


1	SCHEDULE \"A\" :
2	Item No 01 : Complete removal of all existing roof treatment from RCC roof including old hussion felt, tiles etcand preparation of surface with bire brush and cleaning with water complete all as specified and directed.
3	Item No 02 : M&L for 40 mm thick PCC (1:2:4) type B-0 using 12.5 mm graded stone aggregateto roof , floor,chajja, RCC shelves etcat water retaning surfaces with WPC and make proper good slope as directed (Note-wpc will be measured and paid seprately)
4	Item No 03 : M&L for preparation of concrete roof surfaces and applying 20mm thick plaster in CM 1:4 on other than fair faces and finished the surface even and smooth without using extra cement complete all as specified and directed.
5	Item No 04 : M&L for applying a coat of bitumen primer @ 0.3L/sqm on roof surfaces complete all as specified and directed.
6	Item No 05 : M&L for applying 3mm thick APP modified polymeric membrane over the bitumen coat surface weight not less than 3kg/sqm and over lap 100mm and sealed by torch application as per manufacture insteructions complte all as specified and directed
7	Item No 06 : Supply and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including rubbing and polishing of the surface upto 3 cuts complete, including providing skirting upto 150 mm height along the parapet walls in the same manner.
8	Item No 07 : Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. complete all as specified and directed.
9	Item No 09 : M&L rendering 15 mm thick in cement mortar 1:4on wall of brick work or concretesurface, finished fair and evenincluding water proofing compoaund all as specified and directed.
10	Item No 10 : M&L rendering 10 mm thick in cement mortar 1:6on wall of brick work or concretesurface, finished fair and even all as specified and directed.
11	Item No 11 : M&L rendering 5 mm thick in cement mortar 1:3on ceilingof brick or concretesurface, finished fair and evenand smooth without using extra cement all as specified and directed.
12	Item No 12 : M&L for preparing new plastered surfaces and applying two coats of distember oil emulsion white or tinted over 1mm thick putty after one coat of white primer complete all as specified and directed.
13	Item No 13 : M&L for preparing of old surfaces, washing, rubbing down and stopping of disstempered and painted surfaces and applying two coats of distember oil emulsion on wall over 1mm thick putty complete all as specified and directed.
14	Item No 14 : M & L Material & Labour for applying Twocoats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces.
15	Item No 15 : M&L for cleaning ther old surface of all the dirt and green algae with wire brush without disturbing the old plaster and then Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over andover Old surfaces.
16	Item No 16 : Material and labour for complete removal of existing treatment andpreparation of OLD plastered surfaces of ceiling and applying two coats of white wash complete all as specified & directed.
17	Item No 17 : Material and labour for preparation of NEW plastered surfaces of ceiling and applying three coats of white wash complete all as specified & directed.
18	Item No 18 : M&L forrepair and rendering 10mm thickin cm 1 :3on chajjas, facia, roof projection, column sides, beam bottom and sides including throating after removing cracked plaster and concrete includingcleaning of viisible reinforcementandtreating with cement slurry also necessary repair to cracked concreteif any with cement concrete1:2:4 Type B-0 using 12.5mm gradedaggregateincluding necessary scafolding work for double/single storey bldgs all as directed .
19	Item No 19 : Taking down of chowkhats or frame with shutters (without taking off shutters from the frames) n.exc 1.50 Sqm each.
20	Item No 20 : Taking down of chowkhats or frame with shutters (without taking off shutters from the frames) exc 1.50 Sqm & n exc 4 Sqn each.
21	Item No 21 : M&L Pressed steel frames of section 125 x 60 mm for doors with one or more rebates including supply andfixing lugs, hinges, lock strick plate etc complete all as specified.
22	Item No 22 : M&L Pressed steel frames of section 105 x 60 mm for doors with one or more rebates including supply andfixing lugs, hinges, lock strick plate etc complete all as specified.
23	Item No 23 : M&L PCC 1:3:6 type C-0 (using 12.5 mm greded agg) for hold fastand filling of pressed steel frame etc.
24	Item No 24 : S&F 2nd class hardwood factory made 35mm thick Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS: 1003 (Part I), kiln seasoned and chemically pressure treated and including door stopper for each door 01 Nos.
25	Item No 25 : M&L Glazed and skeleton shutters 35 mm thickopen rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chemfered or rounded, fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.20 (a); for doors supplied and fitted to chowkats including door stopper for each door 01 Nos complete all as specified and directed.
26	Item No 26 : S & F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing
27	Item No 27 : Supply & fix factory made solid panel PVC door shutter 30mm thick (style) consisting of frame, made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC , ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for to rail & bottom rail, paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed to getter with solvent cement, including butt hinges to fix the doorcomplete all as specified and directed. .
28	Item No 28 : S & F Mild steel 300mm, ordinary rat tail rod patttern springs including roller and roller plate complete
29	Item No 29 : S&F Aluminium, anodised, barrel tower bolts of 200 mm long and 10mm dia stove enamelled black with bright bolt fixed complete all as specified and directed.
30	Item No 30 : S&F 250 mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified
31	Item No 31 : Supply & fixing125 mm Aluminium handles, cast type, anodised fixed complete all as specified.
32	Item No 32 : S&F Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average with of aperture 1.18mm and fixed withtinned tack, or galvanised wire staples
33	Item No 33 :M&L preparation of new or previously untreated wooden surfaces of any description, not other wise described over 10cm width or girth and apply two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed.
34	Item No 34 : M&L preparation of new or previously untreated steel surface of any description over 10cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.
35	Item No 35 : S&F powder coated Aluminium three track sliding glazed window manufactured with approved aluminium section with three sliding shutters each shutter width one half of the length of window with the following specifiecation and making good the adjascent surfaces :-(a) Window frame of cross section 101mmx40mmx1.5mm thick.(b) Three way track for smooth slding shutters of cross sections 91.80mmx31.75mmx1.1mm thick. (c) Sliding shutter frame of cross section 40x18x1mm.(d) Aluminium glazing stip of size 18.2x16.66mm. (e)4mm thick flat glass superior quality for two shutter. (f) IDPE rubber gasket for fixing glass. (g) Locking cleat/device as shutter 01 Nos. (h) 02 Nos sliding roller per shutters. (j)aluminium wire cloth 0.36mm stainless steel nominal dia of wire and average width of aperature 1.40mm for one shutter.(k) Fixing screws for frame with wall 06 per window with fancy design.(Note: Window will be measured outer to outer frame and no extra to be paid.)
36	Item No 36 : S&F Powder coated aluminium windowand ventilator shutters, side hung type without sash bars, aluminium sections weeighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fitings such as peg stays 150mm long (1 no.) hinge type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified and directed.
37	Item No 37 : M &L Figured glass, pin head 5.0mm type and glazing with oil putty in squares n exc 0.5 sq. m in each pane complete all as specified and directed.
38	Item No 38 : S&F powder coated anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and directed.
39	Item No 39 : Demolition of cement concrete in ground floors and paving exc 15cm thickness(below or above ground level) all as specified and directed.
40	Item No 40 : Demolition of reinforced concreteof any description and any poisition not otherwise specifically provide ( reinforcement cut to faciliatate demolition)
41	Item No 41 : M&L Cement concrete 1:5:10 type E-2 (using 40 mm graded aggregate as in filling around shunken areas complete all as specified and directed.
42	Item No 42 : M&L for 40 mm thick PCC (1:2:4) type B-1 using 20 mm graded stone aggregate with WPC as in sunken portion and making adequate slope toward spout pipe complete all as specified and as directed. NOTE: - Water Proofing Compound shall be measured and paid separately
43	Item No 43 : M&L for rendering 15 mm thick on concrete orbrick surface in CM (1:3) mixed with WPC as per manufacturer instructions and finishes surfaces even and smooth with out using extra cement.Note - WPC will be measured and paid separtely
44	Item No 44 : Supply only liquid water proofing compound complete all as specified and directed.
45	Item No 45 : M&L for applying two coats evenly a tack coat of hot air blown bitumen of grade 85/25 @ 1.50 Kg per sqm per coat (one coat overplaster and one coat on polythene film) including cleaning of surface over polythene film complete all as specified and as directed
46	Item No 46 : M&L for polythene film black 200 micron thick laid in floor, vertical surface etc complete all as specified and directed.
47	Item No 47 : Dismantling floor, hearth or wall tiling incl cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises.
48	Item No 48 : M&LCement concrete 1:2:4 type B0 using 12.5mm graded agg 25 mm thick for laying of floor etc complete all as specified and directed
49	Item No 49 : M&LNon- skid colour ceramic tiles,7 to 8mm thick square / rectangular area of each tile exc 0.06 sqm but n exc 0.11sqm in floor over and including 15mm thick screed bed in CM (1:6), set and jointed in neat cement slurry and pointed in white or coloured cement to match the floor complete all as specified and directed.
50	Item No 50 : M&L Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to matchincluding 15mm thick cement screed bed or bedding layerin CM 1:6 .
51	Item No 51 : M&L Non - Skid Coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to matchincluding 15mm thick cement screed bed or bedding layerin CM 1:6 .
52	Item No 52 : M&L Non - Skid Coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in vertical etc. set and jointed in neat cement slurry and pointed in white or coloured cement to matchincluding 10mm thick cement screed bed or bedding layerin CM 1:4 .
53	Item No 53 : M & L Glazed coloured ceramic tiles in vertical surfaces450x300x7mm thickset and jointed in neat cement slurry and pointed in white or coloured cement to match including 10mm thick rendering in CM 1:4 .
54	Item No 54 : M&L Machine cut kota stone slab flooring 20-25mm thick over incl 20mm thick cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete and incl screed bed of CM 1:6 complete all as specified and directed.
55	Item No 55 : M&L Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete and inclCM 1:4 complete all as specified and directed.
56	Item No 56 :M& L for Granite 16-18mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, win dow-cills, cooking plat forms and like in cement mortar (1:4) including point ing in white cement (1:2) us ing marble dust with admix ture of pigment to match with shade of granite.
57	Item No 57 : Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations
58	Item No 58 : S&Fstainless steel plate rack of size 750 x 600 mm incl. shelves , rod to put plates etc made out of 0.80mm thick stainless steel sheet after taking down old one all as specified and directed .
59	Item No 59 : Supply and fixsinks with drainage board made of stainless steel 1 mm thick sheet for, kitchen or laboratory with plugs, washers and waste pipe; cast iron cantilever brackets and connecting union to pipe overall size 915 mm x 460 mm bowl size 410 mm x 330 mm x 160 mmcomplete all as specified and as directed by Engr-in-Charge.
60	Item No 60 : Taking up or down steel tubing 15mm dia and connections, including cleaning for refixing or removal to store
61	Item No 61 : Taking up or down steel tubing 20mm dia and connections, including cleaning for refixing or removal to store
62	Item No 62 : Supplying and laying of CPVC pipes 16mm dia SDR 11 & Plain CPVC SDR 11 fittings in trenches complete all as specified
63	Item No 63 : Supplying and laying of CPVC pipes 20mm dia SDR 11 & Plain CPVC SDR 11 fittings in trenches complete all as specified
64	Item No 64 : Supply & fixPVC connections of 900mm long suitable for 15mm dia iron pipe including PTMT nuts complete all as specified & directed.
65	Item No 65 : Supply & fix in reapir angular valve with caps, 15 mm dia, cast copper alloy, chromium plated, fancy type with long shank and cup, screwed down, high pressure screwed both ends for iron pipes or for unions and fixed in pipe complete all as specified & directed.
66	Item No 66 : Supply & fix in repair long body bib taps cast copper alloychromium plated with crutch or butterfly handle and caps, screwed down, screwed for iron pipe of 15mm bore, complete all as specified & directed.
67	Item No 67 : M& L for 15mm s Stop valves, cast copper alloy, chromium platedconcealed type screwed down, high pressure, with crutch or butterfly handle, screwed both endsfor iron pipeorfor unionsandfixed
68	Item No 68 : S&F in repair Brass chromium plated shower rose 125mm size all as specified and directed
69	Item No 69 : S&F for 110 mm bore PVCfloor traps plainand 300 mm long out let including jointing with cement concrete type B -1 1:2:4 complete all as specified & directed.
70	Item No 70 : Supply & fixing in repair steel C.P. grating 100/125 mm dia as reqd at site complete all as directed.
71	Item No 71 : Supply and fix PVC bends 110mm bore, any radius complete all as specified & directed.
72	Item No 72 : Supply & fix in repairvitreous china squatting pan of ‘Orrisa pattern’ size 580x440mm, white with, integral foot rest including replacement of ‘P’ or ‘S’ trap, lime concrete bedding and making good floor complete all as specified and directed.
73	Item No 73 : Supply & fix in repair PVC low level flushing cistern of 10 ltrs capacity, ISI Marked, white, symphonic action type with inlet, ball valve, float and handle including brackets, suitable for low level cistern complete all as specified & directed.
74	Item No 74 : S&F in repair Flush pipe of polyethylene of low or high density of PVC, 32 mm dia, for low level cistern complete all as specified and directed.
75	Item No 75 : S&F in repair Gun-metal, globe or gate valves 15mm dia with iron wheel head, screwed both ends for iron pipe and fixed.
76	Item No 76 : S&F in repair Gun-metal, globe or gate valves 20mm dia with iron wheel head, screwed both ends for iron pipe and fixed.
77	Item No 77 : Dismantling water tanks and removingof 500 ltrs capecity complete all as specified and as directed.
78	Item No 78 : S&FPVC rotational moulded polythylenewater storage tanks500 litres capacity (3 layers)incl cover etcBall brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixecomplete all as specified and as directed.
79	Item No 79 : Supply and fixing PVC heavy duty waste pipes of 40/32mm bore suitable for wash hand basins/sinks complete all as specified & directed
80	Item No 80 : S&F as in repair Vitreous China wash basin including pedestal, white, flat back, size 550 x 400 mm, including fixing acessories like galvanised brackets & rag bolts,32 mm CP waste coupling complete all as specified.
81	Item No 81 : S&F PVC(SWR) multi floor trap/nahani trap 75mm dia plain with grating incl jointing with solvent cement.
82	Item No 82 : S&F PVC(SWR)pipe 110 mm dia single socketed in any length with rubber ring joints, fixed to wall with and including stack and clamp.
83	Item No 84 : M&L PVC (SWR) bend with or withiout access door as per site req access of radius 110mm dia
84	Item No 85 : M&L PVC(SWR) Teewith or withiout access door as per site reqr access of radius 110mm dia
85	Item No 86 : M&L PVC (SWR) vent cowl 110mm dia
86	Item No 87 : M&L PVC(SWR) pipes 75mm dia single socketed, in any length with rubber ring joints,laid in trenches or fixed to wall with and including stack and clamp.
87	Item No 88 : M&L PVC (SWR) bendwith or withiout access door as per site req of radius 75mm dia
88	Item No 89 : M&L PVC (SWR) Teewith or withiout access door as per site req or access of radius 75mm dia .
89	Item No 90 : M/L for 75 mm thick cement concrete1:3:6 type C2,using 40 mm stone aggregate finished even & smooth without using extra cement as in plinth protection etc. complete all as specified.
90	Item No 91 : S&F factory made 600 x 450 mm beveled edge mirror 5.5mm thick of selected quality glass and fixed to wooden plugs with chromium plated brass screws and cup washers (In repairs)
91	Item No 92 : Supply & fixpillar taps, fancy typecast copper alloy with capstan heads, chromium plated, screwed down, high pressure with or without lettered “hot” or “cold” with long screwed shanks and fly nut screwed for iron pipe of 15mm bore,complete all as specified & directed.
92	Item No 93 : S & F25 mm stainless steel curtain rod with fancy type braket. complete all as specified and directed.
93	Item No 94 : M&L Prelaminated particle board 18/19 mm thick interior grade , prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screw to timber frame work framed work as in cupboard.incl. leaping all around.
94	Item No 95 : S&F Hasp & staple ,75mm, Aluminium anodised incl bolt to hinge plate and fixed with screws for cupboard.
95	Item No 96 : S&F Continious (piano) hinges, mild steel, bright finish or elecrogalvenised, 30 mm width of flaps(when open) .
96	Item No 97 : M&L mild steel works as in framed work such as grills, gratings, etcwith ends of bars shoulderedand/or riveted or forged into spikes and similar works conforming to Fe-290, Gde-E165 etc, complete all as specified and as directed.
97	Item No 98 : M&L 50mm thick 1:2:4 type B-0 (12.5 graded grade aggregate) as in copings .
98	Item No 99 : Supply and fix Pre-painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.5mm thick of any colour having tensile strength of 550 Mpaas in roof covering/cladding to wall,fixed with self tapping screws as specified.
99	Item No 100 : Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long with aluminium alloy brackets and guard rail
100	Item No 101 : S&F MS work as in angle iron fencing posts & strutsthick for Hand rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors,balusters,nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to IS-15911-2010.
101	SSEWAGE DISPOSAL
102	Item No 102 : Demolition of brick work built in cement morter including all quoins, arches, pillars etc, complete.
103	Item No 103 : Material & labour brick work with old size modular bricks built inCM 1:6 with sub class B, brick & straigh or curved on plain exeeding 6m mean radius complete all as specified.
104	Item No 104 : M & L PCC ( 1 : 4 : 8 ) Type D-2 using 40mm graded stone aggregate in foundations, filling and mass concrete.
105	Item No 105 : Excavation in trenches in soft/loose soil n.exc 1.5 mtr wide and n.exc 1.5 mtr depth and getting out for foundation ect. Or for shafts, well, cesspits, mainholes ect. In any type of soil for foundation and getting out and levelling of bottom surface to required level all as specified and directed.
106	Item No 106 : Returning, filling in including spreading, levelling, watering and well ramming in layers not exc 25 cm thick complete all as specified and directed.
107	Item No 107 : Removing surplus excavated material not exc 50 mtrs and depositing where directed at a level not exc 1.5 mtr above the starting point complete all as specified and directed.
108	Item No 108 : M & L forUltra plus PE, DWCPE (Double waal corrugated) pipe conforming to IS -16098 Part-2:2013 pertaining Structured wall plastics pining system for Non-Pressure drainage and sewage 150mm bore pipe and fittings with non smooth surface, typeB complete all as specified and diredted
109	Item No 109 : M & L concrete bed to drain pipes including packing under, and hunching against the sides of pipes after they are laid and tested in cement concrete 1:4:8 type D2 for 150 mm dia pipe work in foul position.
110	Item No 110 : M & L forUltra plus PE, DWCPE (Double waal corrugated)pipe conforming to IS -16098 Part-2:2013 pertaining Structured wall plastics pining system for Non-Pressure drainage and sewage 200 mm bore pipe and fittings with non smooth surface, typeB complete all as specified and diredted
111	Item No 111 : M & L concrete bed to drain pipes including packing under, and hunching against the sides of pipes after they are laid and tested in cement concrete 1:4:8 type D2 for 200 mm dia pipe work in foul position.
112	Item No 112 : M&L for 15mm thick rendering on Brick masonary wall surfaces in CM 1:4 mixed with water proofing compound finised even and smooth with using extra cement all as directed.
113	Item No 113 : Supply only integral water proofing compound.
114	Item No 114 : M & L for precast RCC 1:2:4 type B-1(using 20mm graded stone aggregate)for manhole cover including placing and set in CM 1:6 all as specified
115	Item No 115 : M & L mild steel deformed or twisted bar(TMT bar)10mm dia and covercut to length bent to shape reqd, incl, cranking benching spirally for copying for columns hooking ends and bending with and including MS wire annealed wire not less than 0.9 mm dia.
116	Item No 116 : M&L for pcc 1:3:6 type C1 using 20mm graded stone aggragate as in bed bricks, coping etc including weathering slightly rounded or chamfered angles and throating making grovves for fixing of man hole cover including necessary form work
117	Item No 117 : Extra for forming fair finished drain aor channel 10cm inner girth in cement concrete using extra cement including finishing the top of benching even and smooth using extra cement (forming channel shall be measured and paid for separately).
118	Item No 118 : Demolition of reinforced cement concrete in ground floors and paving not exceeding 15 cm thickness (below or above ground level) reinforced.
119	Item No 119 : Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required for 150mm/200mm pipe
120	Item No 120 : M & L RCC type B-1 1:2:4 using 20 mm graded agg as in slabs supported on walls as in soak well/septic tank etc complete ( cost in situ) including as per requirement of form work and demolition of RCC.
121	Item No 121 : Demolition of PCC of any description and in any position not otherwise specifically provided for drain etc including removing the same where directed complete all as directed.
122	ROAD PATH CULVERT
123	Item No 122 : Surface excavation n.exc(not exceeding) 30Cm deep and averaging 15 Cm deep andgetting out in soft loose soil
124	Item No 123 : S&F 60 mm thickMachine pressed precast concrete colouredinterlocking paver block any shape and size confirming to IS 15658-2006 , M-35 Grade with grey cement and no pigment complete all as specified and directed.
125	Item No 124 : M/L 100 mm thick cement concrete 1:4:8 type D-2 using (40 mm graded stone agg) as in sub base complete all as specified and directed.
126	Item No 125 : M&L supply and laying of sand including spreading, levelling and ramming in layers n.exc. 50 Mm thick in each layer complete all as directed
127	INTERNAL ELECTRIFICATION
128	Item No 126 : Taking down copper /aluminium point wiring (light, fan, bell,socketor power) complete including fixture and fittings such as switches , ceiling roses , pendent , regulators, sockets, light fitting etc.Removing materials to store for keeping in safe custody or for taking credit (credit a for above items should be made as per condition seperately) and making good distrubed surfaces ofwalls, floors etc complete all as specified and directed at site.
129	Item No 127 : Taking down old/unserviceable distribution board by disconnection of electric connection carefully SPN DBs/TPN DBs/ Main Switch including old unserviceable MCCBs/ MCBs, Isolators, etc and making good to disturbed surface complete all as specified and directed.
130	Item No 128 : Taking down carefully copper/aluminium Sub main wiring of any size fromsurface/concealed /existing conduit of any height and removing materials at site and making good disturbed surfaces of walls, floors roofs etc complete all as specified and directed.
131	Item No 129 : Taking down ceiling fan /exhaust fan of any sweep after disconnecting all necessary electrical connections from ceiling rose to fan, fan blades complete all as specified and as directed and deposit to MES store yard of AGE E/M Dipatoli
132	Item No 130 : M&L for point wiring with 1.5 Sq mmsingle corePVC insulated unsheathedcopper FRLSH multi stranded conductor cable in andincludingConcealed PVC conduitof size 20/25mm ISImarked inclusive oftees ,bend ,elbows etc upto and including sunk in anodized pressed steel box for housing switch socket etc withwhite laminated 3 mm thick hylam sheet cover ISI marked of suitable size complete including PVC insulated multi strandedcopper conductor 1.5Sq mm FRLSH cable as earth wire to common earth dolly for connection to ceiling rose to earth terminalincludingcutting, chasses and makinggooddisturbed surface to match with existing finish with plaster complete all as specified and directed by Engr-in-charge for following :-
133	(a) One light point controlled by one, one way switch 5 Amps
134	(b) One fan point/ exhaust fan point controlled by one, one way switch 5 Amps and regulator
135	(c) One light point controlled by one, two way switch 5 Amps
136	(d)One 3 pin 5 Amps switch socket outlet point controlled by one switch on the same board.
137	(e) One 3 pin 5 Amps switch socket outlet point controlled by one switch on independent boad.
138	(f)One bell point controlled by one, bell switch 5 Amps
139	Item No 131 : Description all as per item No 130 here in before butusing 2.5 sq mm single core copper conductor cable of multistranded FRLSH, PVC insulated unsheathed 1100 volts grade for 5/15 amps switch socket cobmination point including necessary running of2.5 sq mm copper conductor FRLSH, PVC wire as earth continuity conductor along with wiring and connecting to the common earth dolly.
140	Item No 132 : S & F for modular Switch flush type single pole 5/6 amp, two way single module230 Volts complete all as specified and directed at site.
141	Item No 133 : S & F for modular Switch flush type single pole 5/6 amp, one way single module230 Volts complete all as specified and directed at site.
142	Item No 134 : S & F for modular Switch flush type single pole 15/16 amp, 230 Volts complete all as specified and directed at site.
143	Item No 135 : S & F for modular socket outlet 2/3 pin, 5/6 Amp (2 module) 230 Volts complete all as specified and directed at site.
144	Item No 136 : S & F for modular socket outlet 2/3 pin, 06/16 Amp (2 module) 230 Volts complete all as specified and directed at site.
145	Item No 137 : S & F for modular bell push 6 Amp, single module 230 Volts complete all as specified and directed at site.
146	Item No 138 : S & F for Ceiling rose, surface Bakelite with 3 terminals PVC ISImarked for batten fitting complete all as specified
147	Item No 139 : S & Ffor Bell Electric Ding dong type suitable for operation on 230 volt 50 HZ A C supply complete all as specified and as directed
148	Item No 140 : S & Ffor lamp holder , PVC / Polycarbonate type with back plate suitabl for batten/ slanting fittings complete all as specified and directed.
149	Item No 141 : S & F modular cover plate with frame of size 2 module complete all as specified and directed.
150	Item No 142 : S & F modular cover plate with frame of size 3 module complete all as specified and directed.
151	Item No 143 : S & F modular cover plate with frame of size 4 module complete all as specified and directed.
152	Item No 144 : S & F modular cover plate with frame of size 6 module complete all as specified and directed.
153	Item No 145 : S & F modular metal flush box of size 2 module complete all as specified and directed.
154	Item No 146 : S & F modular metal flush box of size 3 module complete all as specified and directed.
155	Item No 147 : S & F modular metal flush box of size 4 module complete all as specified and directed.
156	Item No 148 : S & F modular metal flush box of size 6 module complete all as specified and directed.
157	Item No 149 : S & F blanking plate complete all as specified and directed.
158	Item No 150 : S & F for sheet metal enclosure MCBDBTPN4 way Vertical type with 200 Amps rated bus bar 415 volts double door with magnitic locking system suitable for provision of incoming as 4P MCB and outgoing MCBs including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and as directed.
159	Item No 151 : S & FforMCB tripple pole and neutral rated capacity 63 Amps, 415 Volts breaking capacity 10 KA, \"C\" curve complete all as specified and as directed.
160	Item No 152 : M & L forSub main wiring with approved colour coding as per IS with two single core PVC insulated FRLS cable with stranded copper conductor of size 6 Sq mm nominal area and drawing into suitable size of PVC non metallic rigid heavy duty PVC conduit of white/ ivory colour and its accessaries ISI marked heavy duty of suitable sizeincluding concealed in wall etcone run of PVC insulated with 6.0 Sqmm (nominal area) stranded copper conductor FRLS cable as earth wire complete all as specified and as directed. Note:- Two runs of 6 sqmm cable,one run of 6 sqmm cable and one run of PVC conduit will be measured as one unit
161	Item No 153 : S & F for sheet metal enclosure MCBDBSPN8 way with 200 Amps rated bus bar 240 volts double door with magnitic locking system including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and as directed.
162	Item No 154 : S & F for MCB Single pole and neutral rated capacity 40 Amps, 240 Volts breaking capacity 10 KA, \"C\" curve complete all as specified and as directed.
163	Item No 155 : S & Ffor MCB Single pole rated capacity 6 to 32 Amps, 240 Volts breaking capacity 10 KA, \"C\" curve complete all as specified and as directed.
164	Item No 156 : S&F water heater 25 litre capacity BEE star rating 5, vertical pattern in approved colour, heating element 2.0 KW, adjustable temperature setting knob for temperature settings between 250C to 750C, outer tank made of pre coated metal, inner tank made of extra thick superior cold rolled steel with marine grade glass line coating provided with high density PUF insulation complete.
165	Item No 157 : Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and as directed.
166	Item No 158 : S & F for Highly efficient LED Bulbs, 9 W, used as a ready replacement for existing old unsv bulb complete all as specified and directed
167	Item No 159 : S & F forLED mirror light 10 watts batten aluminium extruded with decorative end caps complete all as specified and as directed.
168	Item No 160 : S & F for Energy saving new generation 10 watts LED bulk head fitting IP 65 luminaire with opel diffuser pre wired with warranty option of 5 years from date of installation andnecessary mounting arrangements, provision of new 3 core multistrandedcopper conductor of size 23/0.193 from ceiling rose to fitting complete all as specified and as directed.
169	Item No 161 : S & F for wall mounted LED tube light fitting 20 watts batten for surface mounted, anodized extruded aluminium housing, high transmissitivity diffuser, high lumen ouputboxtype fitting, 230 volts and intregrated electronic driverconnector block etc with warranty option of 5 years from date of installation complete with all accessories internally pre wired andnecessary mounting arrangements, provision of new 3 core multistrandedcopper conductor of size 23/0.193 from ceiling rose to fitting complete all as specified and as directed.
170	Item No 162 : S & F for Energy saving new generation environmental friendly long life versatile presure die cast aluminium IP 66 for security light fitting luminaire with high power LEDs as light source and electronic driver of capacity 25 watts with pre wired andnecessary mounting arrangements and provision of 2.5 sq mm three core copper conductor cable multi stranded from ceiling rose to light fitting including necessary dia GI pipe medium grade bracket 1.5 mtr long bend to required shape with clamps, nut, bolts complete all as directed.
171	Item No 163 : S & F for energy efficient exhaust fan of 300 mm sweep made of metal body Ventil Air -DS type complete with louver with bolts nuts and washers size of the bolt 15 cm long 12 mm dia embedded in the wall including provision of PVC flexible copper cable of size 23/0.0076 two core from ceiling rose to exhaust fan forconnection and making suitable size ofhole to existing brick wall for fan basecompelte all as specifiedand directed.(Note : Cost of suitable opening wall for fixing exhaust fan is deemed to be includedin overall rate quoted).
172	Item No 164 : Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250 mm
173	Item No 165 : Supply,laying,jointing,testing andcommissioningXLPE insulated, armoured,heavy duty, LT UG cable with aluminium conductor, 1100 volts grade cross sectional area35 sqmm 3.5 core connectedwith aluminium lugsconnectedby cramping toolscomplete all as specified and directed.Note:- Excavation andearth work will be measured and paid separately.
174	Item No 166 : Supply and providing sand cushioning with dry clean sand 15 cm below cable and 8 cm above the cable complete all as specified and directed by Engr-in-charge. Note : Punned thickness shall be measured for the purpose of payments.
175	Item No 167 : Supply and laying burnt bricks old size sub class-B laid in trenches for cable protection with length of brick perpendicular to length of cable complete all as specified and directed.
176	Item No 168 : Supply and fix in replacement of 50 mm bore GI pipe light grade fixed on pole /trenches/wall/road crossing etc complete with clamp nut bolt etcall as specified and directed at site.
177	Item No 169 : M &L for GI Earthing complete with GIearth plate electrode 60cm x 60cm x6 mm buried directly in ground verticvally to size of earth pit not less than 0.90x 0.90 x 2.25 mtr below ground level with top edge ofthe plate at a depth not less than 1.5 mtr below ground level, earth plate connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 of SSRPart - I filling with charcoal dust , and common salt,including necessary excavation and earth work in any type of soil ,perforated watering pipe of size 15 mm dia,funnel with wire mesh, PCC chamber 1:3:6 type C1 (for even finish on both the faces) and RCC cover 1:2:4 Type B1,450 x450 x50 mm thick with 6 mm dia CTD bars 150 mm c/c with 2 Nos of handles of 10 mm dia steel rod all as specified and directed and testing on completion and connected to equipment with lugs and screw nuts etc all as specified and directed by EICNote :(i) 7.5 RM GI earth wire deemed to be included in quoted rates beyond 7.5 RM wire shall be measured and paid separately.(ii) Earth resistance of earth pit should be not more than 02 Ohms on testing after completion if the desired earth resistance is not obtained the earthing will be redone at no extra cost.(iii) Rate quoted by the tenderer is deemed to included salt & Charcoal upto & above 450 mm (Min) top of GI Plate.
178	Item No 170 : S&F in replacement sheet moulded compound (SMC) meter box fire retardant type of size not less than 600x500x150 mm to enclose 04 single phase electric meters with hinge type front operated door having transparent acrylic sheet & proper locking arrangement and flush mounting in wall incl taking down & refixing of serviceable elctric meter & making electric connections including cleaning of disturbed area and making good the disturbed surface and matching the existing specification complete all as directed.
179	EXTERNAL WATER SUPPLY
180	Item No 171 : M&L for drilling and tapping cast iron water mains in position for branch connections of following internal dia 15 to 20 MM dia bore size complete all as specified anddirected..
181	Item No 172 : Takingdown steel tubing with all connections of size 20 MM dia bore complete all as specified and directed.
182	Item No 173 : All as per item No 172 here-in-before but of size 25 mm dia bore complete all as specified and directed.
183	Item No 174 : All as per item No 172 here-in-before but of size 40 mm dia bore complete all as specified and directed.
184	Item No 175 : All as per item No 172 here-in-before but of size 50 mm dia bore complete all as specified and directed.
185	Item No 176 : Supply & Fixingin repair G.Itubes med grade Galvanized with necessary fittings and clamps as per SSR Part -1 laid in trenches /wall/floors concealed or open execution of size 20 mm dia bore complete all as specified and directed.
186	Item No 177 : All as per item No 176 here-in-before but of size 25 mm dia bore complete all as specified and directed.
187	Item No 178 : All as per item No 176 here-in-before but of size 40 mm dia bore complete all as specified and directed.
188	Item No 179 : All as per item No 176 here-in-before but of size 50 mm dia bore complete all as specified and directed.
189	Item No 180 : S&Fin repair gun metal globe or gate valve with iron wheel head, screwed both ends with union,long screw with check nutfor iron pipe incl taking down existing gate valve of size 20 MM dia borecomplete all as specified and directed.
190	Item No 181 : All as per item No 180 here-in-before but of size 25 mm dia bore complete all as specified and directed.
191	Item No 182 : All as per item No 181 here-in-before but of size 40 mm dia bore complete all as specified and directed.
192	Item No 183 : All as per item No 181 here-in-before but of size 50 mm dia bore complete all as specified and directed.
193	Item No 184 : S&F in repair bib taps cast copper alloy with crutch or butter fly handle screwed down, screwed for iron pipe as per SSR Part -1 of size15 mm borecomplete all as specified and directed.
194	Item No 185 : M & L for cutting existing CI water mainsin position for insertion of tee, branch line etc to new water connection of size 100 mm dia borecomplete all as specified and directed
195	Item No 186 : All as per item No 185 here-in-before but in 150 mm diaborecomplete all as specified and directed
196	Item No 187 : Taking up cast iron water mains including all fittings with spigot and socket ends and lead joint including burning out lead joint and recovering lead of CI pipe of size 100 MM dia bore complete all as specified and directed.
197	Item No 188 : All as per item No 187 here-in-before but of size 150 mm dia bore complete all as specified and directed.
198	Item No 189 : Material and labour in repair for run lead joints of CI pipes of size 100 MM dia bore complete all as specified and directed.
199	Item No 190 : All as per item No 189 here-in-before but of size 150 mm dia bore complete all as specified and directed.
200	Item No 191 : S&F DI Fittings as per IS-9525 in all types and sizes and in form of mechanical joints, bends, tees, all types of flanges, socket and spigot, collars caps etc complete all as specified and directed.
201	Item No 192 : Supply, laying and jointing of DI pressure pipes with spigot and socket lining in inner side as per IS:8329/2000 (latest revision) and other relevant standards and mettalic zinc/epoxy coating on outer side, suitable for push on joint (rubber gasket joint) including rubber gasket, in any length laid in trenches/ over masonry pillar and connection to old or new position of Class \"K-7\" of size 100 mm diabore complete all as specified and as directed
202	Item No 193 : All as per item No 192 here-in-before but of size 150 mm dia bore complete all as specified and directed.
203	SCHEDULE \"A\"(Schedule of credit )Schedule of Credit Rs 883748.00 (Minus) inserted by the MES. (Note : Credit amount shall be deducted manually to arrive net amount)

Tender Documents

SR No	FileName	File Description
1	Click here to download tender document	Tender Documents
2	Click here to download tender document	Tender Documents
3	Click here to download tender document	Tender Documents
4	Click here to download tender document	Tender Documents

Also Visit

Tenders

Jharkhand Tenders

Construction Tenders

Building Construction Tenders

Building Work Tenders

Disclaimer

We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.

Top

Tender For Additional / Alternator Cum Special Repair To Jcos Or Md Accommodation At Dipatoli Mil Stn, Dipatoli-Jharkhand

Tender Documents

Disclaimer

About Us

Services

Browse Tenders

For Sales Inquiry

Tender For Additional / Alternator Cum Special Repair To Jcos Or Md Accommodation At Dipatoli Mil Stn, Dipatoli-Jharkhand

Tender Documents

Disclaimer

OTP Verification

About Us

Services

Browse Tenders

For Sales Inquiry

Connect With Us