Tender For Tender For Improvement Works To The Medical And Surgical Blocks Of Chennai Port Authority Hospital, Chennai-Tamil Nadu

TDR : 52871545

Tender Notice
BOQ

18 Days Left

Chennai , Tamil Nadu

Tender Brief : Tender For Tender For Improvement Works To The Medical And Surgical Blocks Of Chennai Port Authority Hospital

Document Fees
Refer document

EMD
₹ 1617000.0 /-

Tender Value
₹ 8.08 Crore /-

Submission Date
30-12-2025

Competition Type
Indian

Bidding Type
Tender

Need a Business Loan? Apply Now !


1	ScheduleA1- Civil works -Medical Block
2	1. Dismantling the existing Nominal concrete 1:3:6 or richer mix including equivalent design mix to the required level, size and shapewherever required without damaging the nearby structures if any, and depositing the debris within a lead of 50m for retransportation and disposal all as per relevant specification and all as directed at site of work including all labour, tools, equipment, fuel, transport, etc., complete.
3	2. Dismantling / cuttingthe existing RCCmembersat Ground floor including stacking the steel without disturbing near by structure and conveying and handing over the serviceable materials, if any, to the departmental stores and wherever requiredincluding collecting and depositing the Debris in Ground level with in a lead of 50m for disposal all as specified andas directed at site of work including all labour, tools, equipments, transport, fuel etc., complete.
4	3. Dismantling and removing theexisting damaged brick work in cement mortar by manually/mechanical meanswherever requiredwithoutdamaging the nearby structures including collecting andbringing downdown the debris to the ground leveland depositing the debris within a lead of 50m for disposingall as specified andas directed at site, including all labour, tools, tackles, equipments, fuel, scaffolding, etc., complete.
5	4. Dismantling and removing the existing IWC / EWCwith tank, W.C.Pan from Toilet without disturbing the existing structure near by including collecting and depositing the debris within a lead of 50m all as directedincluding all labour, tools, equipments, etc., complete.
6	5. Removing the existing damaged wash hand basin with all accessories without disturbing the near by structure and handing over the serviceable materials, if any, to the department stores/ RSD and bringing downthe debris to the ground level and depositing with in a lead of 50mts for disposal, all as directed at site of work including all labour, tools, equipments, transport, fuel, etc., complete.
7	6. Removing the existing damaged Urinal with all accessories without disturbing the near by structure and handing over the serviceable materials, if any, to the department stores and bringing down the debris to the ground level and depositing with in a lead of 50mts for disposal, all as directed at site of work including all labour, tools, equipments, transport, fuel, etc., complete.
8	7. Dismantling AC sheet/Galvalume sheet roofing including ridges, hips, valleys and gutters etc., without disturbing near by structure and conveying and handing over the serviceable materials, if any, to the departmental stores and bringing downthe debris to the ground level for disposal and depositing with in a lead of 50mts for disposal, all as directed at site of work including all labour, tools, equipments, transport, fuel, etc., complete.
9	8. Dismantling and removing the existing worn-out wooden/PVC doors etc., including frame with shutters in all floors without damaging the structures nearby, including transporting and handing over the same to departmental stores / RSO yard within a lead of 3km all as specified and as directed at site of work including all labour, tools, equipments, transport, fuel etc., complete.a). Area Less than 3 M2
10	B). Area More than 3 M2
11	9. Dismantling and removing the existing worn-out wooden / Aluminium Windows / Ventilators etc., including frame with shutters in all floors without damaging the structures nearby, including transporting and handing over the same to departmental stores / RSO yard within a lead of 3km all as specified and as directed at site of work including all labour, tools, equipments, transport, fuel etc., complete.a). Area Less than 3 M2
12	b). Area More than 3 M2
13	c). Ventilators Area Less than 3 M2
14	10. Dismantling and removing the existing Gypsum board / hard board / thermocole false ceiling with frames, clamps etc., without damaging the adjoining structures, transporting and handing over the unserviceable materials to departmental stores/ RSD yard and bringing downthe debris to the ground level and depositing within a lead of 50m for disposal, all as directed including all labour, tools, equipment, scaffolding, transport, fuel, etc., complete.
15	11. Dismantling and removing aluminium/ Gypsum / wooden partitionswherever required without damaging the near by structures including bringing downthe same to ground level, collecting and stacking the unwanted materials within a lead of 50m for disposal and handing over the retrived materials to RSD yard within a lead of 2kms allas specified and as directed at site of work including all labour, tools, equipments, transport, fuel, scaffolding etc., complete.
16	12. Dismantling and removing the existing damaged floor plastering/floor tiles/mosaic/ Cuddappah stone in Cement Mortar to the required thickness wherever required without damaging the structures nearby, includingcollecting and bringing down the debris to the ground level and depositing within a lead of 50m for disposal, all as directed at site of work, including all labour, tools, equipments, transport, fuel, etc., complete
17	13. Dismantling the existing wall tile dadooing including base mortar to the required thickness from the walls and wherever required to receive new finish including collecting and depositing the debris to the ground levelwithin a lead of 50m all as directed including all labour, tools, equipments,etc., complete.
18	14. DismantlingtheexistingBrick jelly lime concrete in sunken portion of toilet area wherever required without damagingthenearbystructurestothe required level, size andshapeand makinggood the disturbed portions if any,includingcollecting and bringing downthe debris to the ground level and depositing within a lead of 50m for disposal, all as per relevant specification andas directed at site, including all labour, tools, equipment, transport, fuel, etc., complete.
19	15. Preparing the surfaces of the sunken portion of toilet area wherever required and plastering with C.M 1:3 (1cement:3 CS sand) 20mm thick withIntegral water proofing liquid admixture conplast (or) equivalent(160ml /50kg of cement all as per relevant standards and specifications and all as directed at site of work including, curing, all materials,labour, tools, equipments, transport, fuel, etc., complete.
20	16. Providing and laying brick jelly cement concrete in mix 1:5:10 (1 cement :5 CS sand :10 broken brick aggregate of 40mm nominal size ) in volumetric proportionsfor sunkenportions of the toilets to the required levels all as per relevant standards and specificationsincluding mixing, transporting, placing, consolidating, curing etc., all as directed including cement and all other materials, labour, tools, equipments, etc., complete.
21	17. Providing and laying Ceramic glazed floor tiles of size 300 x 300 mm or nearest size (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1:4 (1 Cement : 4 Crushed stone sand), jointing with grey cement slurry @ 3.3 kg/ sq.m , complete and joints neatly pointed with white cement added with pigment to match the colour of the tiles, curing all as directed at site of work including cement and all other materials, labour, tools, equpiments, etc., complete.
22	18. Chipping thoroughlythe existingdamagedplasteringfrom walls to receive new finish wherever required without damaging the nearby structures including conveying the debris to the ground level and depositing within a lead of 50m for disposal all as directed including all labour, tools, equipments, scaffolding etc., complete.
23	19. Providing and fixing wall Dadooing using 1st quality ceramic glazed tilesof size 300mm x 200mm or of nearestsize as available in the market conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make and approved colour and shade set in cement mortar 1:3 (1cement: 3 fine CS sand), 12mm thick and joints neatly pointed with white cement added with pigment to match the colour of the tiles, curing all as directed at site of work including cement and all materials, labour, tools, equpiments, transport, fuel, etc., complete.
24	20. Providing flooring with good quality Vitrified Tiles(Double Charge) of size 600mm x 600mm or of nearestsize as available in the market of 10 mm Nominal thickness set in cement mortar 1:4 (1 cement : 4 clean fine CS sand) 20 mm average thick with required slope fixed with neat cement slurry,and joints neatly pointed with white cement added with pigment to match the colour of the tiles,curing all as directed including cement and all other materials labour,tools, equipments , etc., complete
25	21. Refilling with available excavated earth excluding boulders, rubbish, debris, etc., wherever required in layers not exceeding 200 mm thick and as directed at site, including consolidating the deposited earth in layer by watering and ramming including all labour, tools, equipment, etc., complete
26	22. Providing and laying plain cement concrete of mix 1:4:8 (1cement :4 CS sand: 8 hard granite graded stone aggregate of 40mm nominal size) in volumetric proportion for levelling course wherever required including shuttering, mixing, transporting, placing, consolidation by ramming, curing etc., all as per relevant standards and specifications all as directed at site of work including cement, all materials, labour, tools, equipments, transport, fuel, etc., complete.
27	23. a). Providing and fixing factory made uPVC glazed/wire mesh windows/doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge.Three track three panels sliding window with Aluminium channel for roller track, wool pile, nylon rollers with SS 304 body.Using R3 series with frame (98mm & above) x (40mm & above) & sash (30mm & above) x (55mm & above) with zinc alloy (zamak) powder coated handle on two end panels along with multi-point locking system (Height upto 1.8 metre).
28	23. b). Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work
29	24. Providing Half brick work using bricks of class designation 50setin cement mortar 1:4 (1 Cement: 4 CS sand)in footh path, kitchen platform, partition in ground level upto fifth floor level and wherever necessary, all as directed at site of work, including scaffolding, labour, materials, Cement, tools, curing, etc., complete.
30	25. Preparing the surfaces of walls and plastering in cement mortar 1:5 (1 cement : 5 CS sand), 12mm thick to the required finishwherever required all as directed at site of work, including cement and other materials, labour, tools, equipments, scaffolding, curing etc., complete.
31	26. Providing and fixing granite slab of 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size of colour black, Cherry/Ruby red approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 CS sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels including all materials, labour, tools, equipments, curing etc., complete.
32	27. Preparing the surfaces of old wooden members and applying two coats of synthatic enamelpaint (Asian / Nippon / Berger or equivalent)of approved brand and colour of good quality to give an even shadeall as directed at site of work including all labour, materials, tools, tackles, equipments, brushes, scaffolding, etc., complete. NOTE: 1. Necessary painting co-efficient shall be allowedas per Ch.P.A. engineering manual.2. The above quantity is inclusive of painting co-efficient.
33	28. Providing and fixing SFRC (Steel Fiber Reinforced Concrete) Manhole cover with frame of size600 x 600 mm for Manhole and wherever required in mix 1:1.5:3 ( 1 cement : 1.5 C.S.sand: 3 hard granite graded stone aggregate of 20mm nominal size) in volumetric proportions to the required size, all as per relevant specifications, drawings and as directed includingnecessary form work, mixing, transporting, placing, compacting, curing, finishing the exposed concrete surface withneat cement punning at 2.2 kg/Sq.m as directed, includingremoving the existing damaged manhole cover, lifting, handling, transporting and placing the cover over the frame in correct position and alignment, providing necessary lifting holes including all materials, labour, tools, plants, equipments, fuel, etc., complete.
34	29. Dismantling of Gully trap including chamber wherever required without damaging the structures nearby and collecting, stacking the debris within a lead of 50m for disposal all as directed at site of work including costs of all labour, tools, equipments, etc., complete.
35	30. Providing and fixing Gully trap including constrcution of Chamber of size 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 CS sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in reinforced cement concrete slab 1:1.5:3 mix (1 cement : 1.5 CS sand : 3 graded stone aggregate 20 mm nominal size), including necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 crushed stone sand) 12mm thick, finished with a floating coat of neat cement all as directed at site of work including all labour, materials, tools, tackles, equipments, brushes, etc., complete.
36	31. Earth work excavation upto 1.50m in ordinary soil, sand, clay mixed with roots, boulders weighing individually less thasn 250kg debris, rubbish etc., as existing at site of work for all foundations and other such works as directed including dressing of sides ramming of bottom all as per relevant specification and as directed at site, depositing the excavated earth within a lead of 50m for transportation including shoring, strutting, all labour, tools, tackles, equipments, fuel, etc., complete.
37	32.Providing and laying reinforced cement concrete of mix 1:1.5:3 (1 cement:1.5 CS sand:3 hard graded stone aggregate of 20mm nominal size) in volumetric proportions for Drain Side Walls and wherever required all as per relevant specification and as directed at site of work including cement, mixing, transporting, placing, vibrating,ramming, consolidating, curing, shuttering, all materials, labour, tools, plants, equipments, fuel, etc., complete.
38	33. Casting, transporting and placing RCCpre cast cover slabs 100 mm thick in mix 1:1.5:3 (1 cement : 1.5 CS sand : 3 hard granite stone graded aggregate of 20mm nominal size) in volumetric proportion including formwork, mixing, transporting, placing, consolidating, etc., including finishing the exposed surfaces with a floating coat of neat cement punning 2.2kg/sqm and as directed including necessary curing, handling, placing and fixing in position and all other materials, labour, tools, equipments etc., complete.Note: Supplying and fabrication of steel reinforcement will be measured and paid seprately under the relevant item.
39	34. Supplying, fabricating and placing in positionHYSD (Fe 500/ 550 grade) TMT steel bars as reinforcement for all RCC works wherever required, including handling, cutting, bending and tying with 1.25mm dia black annealed steel binding wire including placing, all as per relevant specification, drawings and as directed,including all materials, labour, tools, equipment, transport, fuel, etc., complete.Note: 1.The rate shall be inclusive of cost of reinforcement steel, binding wire and fabrication charges etc., complete. Binding wire will not be measured for payment purpose.
40	35. Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Clerestory windows & other Frames/Chowkhat of size 45 x 85 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately).
41	36. Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge and as directed at site of work including transporting, placing, all materials, labour, tools, plants, equipments, fuel, etc., complete.(Note: stainless steel butt hinges and necessary S.S screws shall be paid separately)
42	37. Providing and fixing IS : 12817 marked stainless steel fittings (heavy weight) with stainless steel screws for doors, etc., as directed at site of work with the approval of engineer in charge, including all materials, labour, tools, equipments, etc. completea) Butt Hinges 125mm
43	b) Tower bolt 150 mm
44	c) Tower bolt 75mm
45	d) Aldrop 250mm
46	e) 125mm Handle
47	38. Preparing the surfaces of existing ceiling etc., and applying onecoatofwhite washing with premium acrylic emulsion paint of interior grade, (Asian / Nippon / Berger or equivalent) having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour all as directed at site of work including all labour, scaffolding, materials, tools, equipments, brushes, safety ladder, safetybelts, safety helmets, etc.,complete.
48	39. Preparing the surfaces of existing interior walls etc., and applyingtwocoatsofColour washing with premium acrylic emulsion paint of interior grade, (Asian / Nippon / Berger or equivalent) having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including one coat of interior primer wherever required to achieve even shade and colour all as directed at site of work including all labour, scaffolding, materials, tools, equipments, brushes, safety ladder, safetybelts, safety helmets, etc.,complete.
49	40. Providing and fixing White vitreous china Orissa pattern W.C pan of size 580x 440 mm with integral type foot rest squatting pan (Indian Type WC Pan) Parryware/Hindware/ jaquar or equivalent with 100 mm sand cast iron P or S trap, 10 litre low level white PVC flushing cistern, incluing flush pipe, with manually controlled device (Handle lever) conforming to IS :7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required, all as directed at site of work including all materials, labour, tools, equipments, etc., complete.
50	41. Providing and fixing white vitreous china pedastal type water closet ( European type W.C pan) Parryware/Hindware/ jaquar or equivalent with seat and lid , 10 litre low level white PVC flushing cistern, including flush pipe, with manually controlled device(Hnadle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required, all as directed at site of work including all materials, labour, tools, equipments, etc., complete.
51	42. Providing and fixing good quality vitreous white wash hand basin ofsize 550x 400 mm or nearest size as available in the market ( Parryware/Hindware/ jaquar or equivalent) with single 15mm C.P brass pillar tap. CP waste fitting , 32mm dia cp brass union, 15 mm dia PVCinlet connection, 32mm dia pvc waste pipe fittings, a pair of cast iron brackets etc as available in the market suitable for fixing the wash hand basin, including painting the brackets etc with two coats of syntheticenamel paint over one coat of primer fixing the brackets with teak wood plugand making good the disturbed portion, etc., all in sound working condition all as per relevant specification and as directed including all materials, labour, tools,equipments,etc., complete.
52	43. Providing and fixing white vitreous china flat back type lipped front urinal basin of 430x260x350 mm sizes or asavailable in the market (Parryware/Hindware/ jaquar or equivalent) as per manufacturers specification with PVC flexible flush pipe with clamp, teakwood plugs, screws with all fittings and fixtures for inlet and outlet arrangements etc., all as per relevant secification and as directed at site in sound working condition, including all materials, labour, tools, equipment, etc., complete.
53	44. Dismantling and Removing the existing damaged PVC / Cast Iron / GI pipes with all accessories, wherever required without damaging near by structuresincluding collecting and stacking the dismantled pipes within a lead of 50m for disposal , transporting and handing over the unserviceable materials to departmental stores/ RSD yard all as specified and as directed at site of work including all labour, tools, tackles, equipments, scaffolding, transport, fuel, safety ladder, safety belts, safety helmets, safety netsetc., complete.
54	45. Removing the existing damaged taps, wall mixture, shower arm with shower rose, Health facuet, angle cock etc.,with all accessories without disturbing near by structure and conveying and handing over the serviceable materials, if any, to the department stores, all as directed at site of work including all labour, tools, equipments, transport, fuel, etc., complete.
55	46. Supplying and fixingChlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply (Varun / Finolex / Trubore or equivalent) for external / internal works exposed on wall with CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing with all required accessories like tees, bends, couplings, elbows, reducers, unions, etc.,jointing of pipes & fittings with one step CPVC solvent cement and testing of joints andincluding punching the masonry/concrete wherever required and making good the disturbed portions, all as per relevant specification and directed at site of work,labour, tools, equipments, scaffolding etc., completea) 32 mm dia.
56	46.b) 25mm dia.
57	46.c) 20mm dia.
58	46.Providing and fixing First quality Gun metal gate valve (Full way valve with Handle) of following sizesto the water pipe lines in all floors in sound working condition by removing the existing wheel valve including making the joints water tight and testing etc., all as directed at site of work including all materials, labour, tools, equipments, etc., complete.(d). 32mm dia.
59	46.(e) 25 mm dia.
60	47. Providing, fixing and laying of pipes on floors of, approved quality rigid PVC pipes of 75/110mm outside diameters 6 Kgf/sq.cm pressure-(Finolex (or) Trubore (or) Varun (or) Supreme or equivalent) for waste water lines/sewage lines including necessary specials like bends, tees, elbows, clamps and specials, etc., wherever required, including joining the pipes using necessary adhesives, and making connections to floor traps, gully traps manholes etc., including cutting the floor concrete masonry and making good the disturbed portions all as directed at site of work including all materials, labour, tools, equipments, scaffolding, cement etc., complete.a). 110mm Dia
61	b). 75mm Dia
62	48. Providing and fixing 110mm dia PVC Nahani trap (floor trap with gratings suitable for PVC drainage pipe) embedding the trap making the joints water tight etc., allas directed including allmaterials, labour, tools, equipments etc., complete.
63	49. Supplying and fixing the sanitary fittings with First qualityC.P fittings (Parryware/Hindware/ jaquar /Metro or equivalent) intoilets in sound working condition including testing etc., all as directed at site of work including all materials, labour, tools, equipments, etc., complete.a) Health Faucet
64	b) Short body Tap 15mm dia conforming to IS:8931
65	c) Stop cock 15mm dia (concealed) conforming to IS:8931
66	d) 32mm size PTMT Bottle Trap
67	e) Angle valve 15mm dia
68	f) Long body Tap(Bib Cock) 15mm
69	50. Loading, transporting, dumping and leveling the surplus earth and debris etc., within a lead of 3 kms outsidethe Port premises all as per relevant specifications and as directed including all labour, transport, tools, equipments, fuel, etc., complete.Note:1.The tenderer shall maintain trip sheets in triplicate in Trust\"s approved format at his own cost.2.Payment will be based on the lorry cubical content. No deduction of voids for debris will be made. 4. 20%deduction of voids for surplus earthwill be made. However the final quantity will be restricted to actual quantity of debris dismantling /demolishing items.(a) Surplus Earth
70	(b) Debris
71	51. Providing and fixing double scaffolding system (cup lock type) on the exterior side, up to seven story height made with 40 mm dia M.S. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with M.S. tubes, M.S. tube challies, M.S. clamps and M.S. staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it thereafter. The scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspection of work at required locations with essential safety features for the workmen, including removing the scaffolding with platform after completion of works all as directed at site of work including all labour materials tools equipmentstransport fuel etc complete.. The elevational area of the scaffolding shall be measured for payment purpose.Note (1) 75% of payment may be relaeased after erecting of scaffolding in all respect.(2) The balance 25% ofpayment may be released after completion of improvement works and removal of scaffolding
72	52. Supplying diluting and injecting chemical emulsion for post constructional anti termite treatment with chlorpyrlphos Emulsifiable concentrate with 1% concentration (i.e. one litre of chemical for every 20 litires of emulsion) in soil along internal andexternal wall using chemical emulsion at 2.25 litire per linear metre inlcuding drilling and plugging holes etc. and treating the soil under floors, masonry / concrete inside and outside of buildings wherever required, using chemical emulsion at 1 litre per hole at 30cm interval including drilling 12mm dia holes and plugging them with cement mortar 1:2 to the full depth of the hole and treating the points of contact of wood work by chemical emulsion (in oil of kerosene based solution) at 0.5 litres per hole by drilling 6mm dia at downward angle of 45 degree at 150mm c/c and sealing the same and as directed including all material (including cement) labour, tools, scaffolding, ladder, equipments etc. complete
73	53. Supplying, fabricating and fixing the M.S gate, window / Ventilator grill, Ladder as per existing or as directed at site using structrual steel, etc., using as verticles, horizontals and diagonal members, including fixing including cutting the flats, bars, etc., to the reqired length, welding the joints all as directed at site of work , providing scaffolding, fixingin proper alignment, all as directed at site of work including applying a priming coat of approved steel primer all materials, labour, tools, transport, equipments, fuel, etc., complete.Note:1. The payment is based on the total weight of the MS flats, bars, etc., as fabricated. 2. The weighment will made at site or any other place as approved by the engineer-in-charge. Necessary charges for transport, weighment. etc., will be borne by the contractor.
74	Schedule- A2 Civil Works -Surgical Block
75	1.Providing and fixing double scaffolding system (cup lock type) on the exterior side, up to seven story height made with 40 mm dia M.S. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with M.S. tubes, M.S. tube challies, M.S. clamps and M.S. staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it thereafter. The scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspection of work at required locations with essential safety features for the workmen, including removing the scaffolding with platform after completion of works all as directed at site of work including all labour materials tools equipmentstransport fuel etc complete.. The elevational area of the scaffolding shall be measured for payment purpose.Note (1) 75% of payment may be relaeased after erecting of scaffolding in all respect.(2) The balance 25% ofpayment may be released after completion of improvement works and removal of scaffolding
76	2. Dismantling and removing the existing damaged floor plastering/floor tiles/mosaic/ Cuddappah stone in Cement Mortar to the required thick wherever required without damaging the structure nearby, includingcollecting and bringing downthe debris to the ground level and depositing within a lead of 50m for disposal, all as directed at site of work, including all labour, tools, equipments, transport, fuel, etc., complete
77	3. Dismantlingand removing the existing wall plastering / tile dadoing including base mortar to the required thick from the walls wherever required to receive new finish including collecting and depositing the debris to the ground levelwithin a lead of 50m all as directed including all labour, tools, equipments, transport, fuel,etc., complete.
78	4. Dismantling and removing the existing worn-out wooden/ PVC doors/ windows/ ventilators etc., including frame with shutters in all floors without damaging the structures nearby, including transporting and handing over the same to departmental stores / RSO yard within a lead of 3km all as specified and as directed at site of work including all labour, tools, equipments, transport, fuel etc., complete.a). Area Less than 3 M2
79	b). Area More than 3 M2
80	c).Dismantling and removing the existing wornout wooden/Aluminium partition etc., including frame with shutters and handing over the same to departmental stores/RSD yard within a lead of 3km, without damaging the adjoining structures, and bringing downthe debris to the ground level and depositing within a lead of 50m for disposal, all as directed including all labour, tools, equipment, scaffolding, transport, fuel, etc., complete.
81	5. Dismantling and removing the existing Gypsum board / thermocole false ceiling with frames, clamps etc., without damaging the adjoining structures, transporting and handing over the unserviceable materials to departmental stores/ RSD yard and bringing downthe debris to the ground level and depositing within a lead of 50m for disposal, all as directed including all labour, tools, equipment, scaffolding, transport, fuel, etc., complete.
82	6. Dismantling and Removing the existing damaged PVC / Cast Iron / GI pipes with all accessories, wherever required without damaging near by structures and handing over the unserviceable materials to departmental stores / RSD yardincluding collecting and stacking the dismantled pipes within a lead of 50m for disposal all as specified and as directed at site of work including all labour, tools, tackles, equipments, scaffolding, transport, fuel, safety ladder, safety belts, safety helmets, safety netsetc., complete.
83	7. Dismantling and removing the existing IWC / EWC with floor concrete from Toiletwithout disturbing the existing structure near by including collecting and depositing the debris within a lead of 50m all as directedincluding all labour, tools, equipments, etc., complete.
84	8. Removing the existing damaged Urinal with all accessories without disturbing near by structureand bringing down the debris to the ground level and depositing with in a lead of 50mts for disposal, all as directed at site of work including all labour, tools, equipments, transport, fuel, etc., complete.
85	9. Removing the existing damaged wash hand basin with all accessories without disturbing near by structure and conveying and handing over the serviceable materials, if any, to the department stores/ RSD yardand bringing down the debris to the ground level and depositing with in a lead of 50mts for disposal, all as directed at site of work including all labour, tools, equipments, transport, fuel, etc., complete.
86	10. Dismantling / cuttingthe existing RCCmembers at all floors including stacking the steel without disturbing near by structure and conveying and handing over the serviceable materials, if any, to the department stores and wherever requiredincluding collecting and depositing the Debris in Ground level with in a lead of 50m for disposal all as specified andas directed at site of work including all labour, tools, equipments, transport, fuel etc., complete.
87	11. Dismantling the existing Plain cement concrete in Rich mix to the required level, size and shape wherever required without damaging the nearby structures if any, and depositing the debris within a lead of 50m for retransportation and disposal all as per relevant specification and all as directed at site of work including all labour, tools, equipment, fuel, transport, etc., complete.
88	12. Dismantling the existing Plain cement concrete in lean mix to the required level, size and shape wherever required without damaging the nearby structures if any, and depositing the debris within a lead of 50m for retransportation and disposal all as per relevant specification and all as directed at site of work including all labour, tools, equipment, fuel, transport, etc., complete.
89	13. Dismantling and removing theexisting damaged brick work in cement mortar by manually/mechanicallywherever requiredwithout damaging the nearby structures including collecting and bringing down the debris to the ground leveland depositing the debris within a lead of 50m for disposingall as specified andas directed at site, including all labour, tools, tackles, equipments, fuel, scaffolding, etc., complete.
90	14. Dismantling and removing the existing wornout MS grill, MS gates, window grill, ventilators grill etc without damaging the structures nearby, including transporting and handing over the same to departmental stores / RSO yard within a lead of 3km all as specified and as directed at site of work including all labour, tools, equipments, transport, fuel etc., complete.
91	15. DismantlingtheexistingBrick jelly lime concrete / Cement Concrete in sunken portion of toilet area wherever required without damagingthenearbystructurestothe required level, size andshapeand makinggood the disturbed portions if any,includingcollecting and bringing downthe debris to the ground level and depositing within a lead of 50m for disposal, all as per relevant specification andas directed at site, including all labour, tools, equipment, transport, fuel, etc., complete.
92	16. Removing the existing damaged taps, wall mixture, shower arm withrose, Health facuet, angle cock, towel rod, etc.,with all accessories without disturbing near by structure and conveying and handing over the serviceable materials, if any, to the department stores /RSD, all as directed at site of work including all labour, tools, equipments, transport, fuel, etc., complete.
93	17. Earth work excavation in ordinary soil, sand, clay mixed with roots, boulders weighing individually less than 250kg debris, rubbish etc., as existing at site of work for all foundations and other such works up to 1.50m depth including dressing of sides ramming of bottom all as per relevant specification and as directed at site, depositing the excavated earth within a lead of 50m for transportation including shoring, strutting, all labour, tools, tackles, equipments, fuel, etc., complete.
94	18. Refilling with available excavated earth excluding boulders, rubbish, debris, etc., wherever required in layers not exceeding 200 mm thick and as directed at site, including consolidating the deposited earth in layer by watering and ramming including all labour, tools, equipment, etc., complete
95	19. Providing and laying plain cement concrete of mix 1:4:8 (1cement :4 Crushed stone sand: 8 hard granite graded stone aggregate of 40mm nominal size) in volumetric proportion for levelling course wherever required including shuttering, mixing, transporting, placing, consolidation by ramming, curing etc., all as directed at site of work includingcost of cement, all materials, labour, tools, equipments, transport, fuel, etc., complete.
96	20. Providing Brick work with common burnt clay selected F.P.S. (non modular) bricks of class designation 7.5 in exposed brick work including making horizontal and vertical grooves 10 mm wide 12 mm deep complete in cement mortar 1:5 (1 cement : 5 CS sand) for raising walls in all floors upto fifth floor level and wherever required, all as per the details and as specified in the relevantschedule and as directed at site of work including scaffolding,curing, cement, all other materials, labour, tools, equipments, transport, fuel, etc., complete.
97	21. Providing Half brick work with common burnt clay (non-modular) bricks of class designation 7.5setin cement mortar 1:4 (1 Cement: 4 CS sand)in toilet / bathroom / partition in ground level upto fifth floor level and wherever necessary, all as directed at site of work, including scaffolding, labour, materials, Cement, tools, curing, etc., complete.
98	22. Providing Brick pillasterwith common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V levelin CM 1:4 (1 cement : 4 CS sand) wherever required, all as directed at site of work including cost of cement , all materials, labour, tools, equipments, scaffolding, curing, transport, fuel, etc., complete
99	23. Casting, transporting and placing RCC pre cast cover slabs of various thickness more than 40 mm thick in mix 1:1.5:3 (1 cement : 1.5 CS sand : 3 hard granite stone graded aggregate of 20mm nominal size) in volumetric proportion including formwork, mixing, transporting, placing, consolidating, etc., including finishing the exposed surfacesand as directed including necessary form work, curing, handling, placing and fixing in position with CM 1:3(one cement : three fine CS sand) including cost of cement and all other materials, labour, tools, equipments etc., complete.Note: Supplying and fabrication of steel reinforcement will be measured and paid seprately under the relevant item.
100	24. Providing and laying plain cement concrete of mix 1:1.5:3 (1 cement:1.5 CS sand:3 hard graded stone aggregate of 20mm nominal size) in volumetric proportions wherever required all as per relevant specification and as directed at site of work including mixing, transporting, placing, vibrating, ramming, consolidating, curing, shuttering, including cost ofcement all materials, labour, tools, plants, equipments, fuel, etc., complete.
101	25. Providing and laying plain cement concrete of mix 1:2:4 (1 cement: 2 CS sand:4 hard graded stone aggregate of 20mm nominal size) in volumetric proportions wherever required all as per relevant specification and as directed at site of work including mixing, transporting, placing, vibrating, ramming, consolidating, curing, shuttering,including cost of cement, all materials, labour, tools, plants, equipments, fuel, etc., complete.
102	26. Supplying, fabricating and placing in positionHYSD (Fe 500/ 550 grade) TMT steel bars as reinforcement for all RCC works wherever required, including handling, cutting, bending and tying with 1.25mm dia black annealed steel binding wire including placing, all as per relevant specification, drawings and as directed,including all materials, labour, tools, equipment, transport, fuel, etc., complete.Note: (i) The rate shall be inclusive of cost of reinforcement steel, binding wire and fabrication charges etc., complete. Binding wire will not be measured for payment purpose.
103	27. Supplying, fabricating and fixing the M.S gate, window / Ventilator grill, Ladder, etc.,as per existing or as directed at site using suitable MS Square bars, MS Square sections, MS Flats, M.S.sheet, etc., using as verticles, horizontals and diagonal members,including cutting the flats, bars, etc., to the reqired length, welding the joints all as directed at site of workproviding scaffolding, fixing gate in proper alignment including applying one coat of red oxide primer all as directed at site of work including all materials, labour, tools, transport, equipments, fuel, etc., complete.Note:1. The payment is based on the total weight of the MS flats, bars, etc., as fabricated. 2. The weighment will made at site or any other place as approved by the engineer-in-charge. Necessary charges for transport, weighment. etc., will be borne by the contractor.
104	28. Preparing the surfaces of the floor area wherever required and plastering with C.M 1:3 (1cement:3 fine CS sand) 20mm thickall as per relevant specifications and all as directed at site of work including, curing, cost of cement, all materials,labour, tools, equipments, transport, fuel, etc., complete.
105	29. Preparing the surfaces of the floor area wherever required and plastering with C.M 1:3 (1cement:3 fine CS sand) 20mm thick with water proofing compoundof integral water proofing liquid admixture conplast ( 160ml / 50kg of cement) all as per relevant specifications and all as directed at site of work including, curing, cost of cement, all materials,labour, tools, equipments, transport, fuel, etc., complete.
106	30. Preparing the surfaces of walls and plastering in cement mortar 1:5 (1 cement : 5 fine CS sand), 12mm thick to the required finish all as directed at site of work, including cost ofcement and other materials, labour, tools, equipments, scaffolding, curing etc., complete.
107	31. Preparing the surfaces of ceilingand plastering in cement mortar 1:3 (1cement : 3 clean fine CS sand) 6 - 10 mm thick to the required finish, all as directed at site of work including alllabour, cement, materials, tools, equipments, scaffolding, curing, etc. complete.
108	32. Providing and laying Ceramic glazed floor tiles of size 300 x 300 mm or nearest size (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1:4 (1 Cement : 4 CS sand), jointing with grey cement slurry @ 3.3 kg/ sq.m , complete and joints neatly pointed with white cement added with pigment to match the colour of the tiles, curing all as directed at site of work including cement and all other materials, labour, tools, equpiments, etc., complete.
109	33. Providing and laying Ceramic glazed wall dadooing / skirtingwith tiles conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 12 mm thick bed of cement mortar 1:3 (1 Cement : 3 CS sand), and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade,all as directed at site of work including all materials, labour, tools, equpiments, scaffolding, curing, etc., complete.
110	34. Providing and layingVitrified Tile flooring(Double Charge) of size 600mm x 600mm or nearestsize with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 CS sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and pigments to match the colour of the tiles, all as directed including cost of cement and all other materials, labour,tools, equipments, curing etc., complete
111	35. Providing and fixing granite slab of 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for cupboard, shelves, racks and similar locations of required size of colour black, Cherry/Ruby red approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 CS sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges, etc. complete at all levels including all materials, labour, tools, equipments, curing etc., complete.
112	36. Providing edge moulding to 18 mm thick granite stone for cupboard, shelves, racks and similar locations etc., including machine polishing to edge, etc., all as directed at site of work including all materials, labour, tools, equipments, curing etc., complete.
113	37. Providing and fixingsal/padak wood frame for doors / windows / ventilators with necessary M.S. hold fasts / clamps of size 40x5x400mm longfixed suitably to the masonry / concrete including cutting pockets and grouting with plain cement concrete 1:3:6 (1 cement : 3 CS sand : 6 hard granite graded stone aggregate of 20mm nominal size) in volumetric proportions, curing including oil type wood preservative of approved brand and manufacture on the portions of the timber abutting against masonry / concrete all as directed at site of work including cement and all other materials, labour, tools, scaffolding equipment, etc., complete.
114	38. Providing and fixing Second class teak wood shutterframe with wood panelleing /glazed shutters 30mm thick for doors, windows / cupboard etc., including top rail, bottom rail, lock rail etc., all as per relevant specifications as directed at site of work including all materials, labour, tools, equipments, transport, fuel etc., complete. Note:Necessary fixtures like butt hinges, Aldrop and tower bolts, etc., will be paid under relevant item of BOQ
115	39. Providing and fixing sal/Padak wood for Cup-board Main frame and shutter including coach screwsincluding applying one coat of coal tar paint on the portions of the timber abutting against masonry / concrete all as directed at site of work including all materials, labour, tools, equipment, etc., complete.
116	40. Providing and fixing of colour anodized aluminium main frame for doors and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia. and size, including necessary filling up the gaps at junctions, i.e., at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically (anodised transparent or dyed to required shade according to IS: 1868,Minimum anodic coating of grade AC 15) wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all as per relevant specifications as directed at site of work including all materials, labour, tools, equipments, transport, fuel etc., complete.
117	41. Providing and fixing colour anodized aluminium sections for Shutter frames of doors and partitions with extruded built up standard tubular and other sections of approved make (INDAL or JINDAL or Equivalent make) with clear anodized aluminium coating (minimum anodized coating of Grade AC 15) conforming to IS 1868 including supplying and fixing necessary accessories like anodised aluminium cleat angles, snap on beadings (clips) for glazing / panelling, C.P. brass screws, anodised aluminium push plates 100mm wide both sides fixed with G.I. Bolts and nuts including necessary metal screws and concealed locking arrangements with woollen felt, filling the hollows of frames with wooden inserts of required length of approved quality wherever required to facilitate fixing of fittings all as shown in the drawing and as directed including all materials, labour, tools, equipments etc., complete.
118	42. Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo withIS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. all as directed including all materials, labour, tools, equipments etc., complete.
119	43. Providingand fixing Prelaminated flat pressed three layer or graded wood particle board with both sides decorative lamination, (medium density) Grade I, Type II conforming and marked to IS : 12823 (exterior grade) 12 mm thick fordoors / partitions all as directed including all materials, labour, tools, equipments,transport,etc., complete.
120	44. a). Supplying and fixing in position 5.5 mm thick plain glass (saint Gobain or Modiguard or equivalent) for doors / windows / partitions with necessary accessories like wooden beading/ Rubber beading, screw etc., all as directed at site including removing the old damaged glass, all materials, labour, tools, equipments, transport, fuel, etc., complete.Note: The actual area of glass used alone measured for payment purpose.
121	44. b). Supplying and fixing in position 4 mm thick Frosted glass sheet (saint Gobain or Modiguard or equivalent) (weight not lessthan 10kg/sqm) for doors / windows / partitions with necessary accessories like wooden beading/ Rubber beading, screw etc., all as directed at site including removing the old damaged glass, all materials, labour, tools, equipments, transport, fuel, etc., complete.Note: The actual area of glass used alone measured for payment purpose.
122	45. Providing and laying brick jelly cement concrete in mix 1:5:10 (1 cement :5 CS sand :10 broken brick aggregate of 40mm nominal size ) in volumetric proportionsfor sunkenportion of the toilet to the required thicknessincluding mixing, transporting, placing, consolidating, curing etc., all as directed including cement and all other materials, labour, tools, equipments, etc., complete.
123	46. Providing and fixing white vitreous china pedastal type water closet ( European type W.C pan) with seat and lid, 10 litre low level white PVC flushing cistern, including flush pipe, with manually controlled device(Handle lever) conforming to IS : 7231, with all fittings and fixtures complete,in sound working condition, including cutting and making good the walls and floors wherever required, all as directed at site of work including all materials, labour, tools, equipments, etc., complete.
124	47. Providing and fixing White vitreous china Orissa pattern W.C pan of size 580x 440 mm with integral type foot rest squatting pan (Indian Type WC Pan) with 100 mm sand cast iron P or S trap, 10 litre low level white PVC flushing cistern, incluing flush pipe, with manually controlled device (Handle lever) conforming to IS :7231, with all fittings and fixtures complete, in sound working condition, including cutting and making good the walls and floors wherever required, all as directed at site of work including all materials, labour, tools, equipments, etc., complete.
125	48. Providing and fixing white vitreous china flat back type lipped front urinal basin of 430x260x350 mm sizesavailable in the market as per manufacturers specification with PVC flexible flush pipe with clamp, teakwood plugs, screws with necessary fittings and fixtures for inlet and outlet arrangements etc., all as per relevant secification and as directed at site in sound working condition, including all materials, labour, tools, equipment, etc., complete.
126	49. a). Providing and fixing good quality vitreous white wash hand basin ofsize 550x 400 mm or nearest size as available in the market ( parrywareor equivalent) with single 15mm C.P brass pillar tap. CP waste fitting , 32mm dia cp brass union, 15 mm dia PVCinlet connection, 32mm dia pvc waste pipe fittings, a pair of cast iron brackets etc as available in the market suitable for fixing the wash hand basin, including painting the brackets etc with two coats of syntheticenamel paint over one coat of primer fixing the brackets with teak wood plugand making good the disturbed portion, etc., all in sound working condition all as per relevant specification and as directed including all materials, labour, tools,equipments,etc., complete.
127	49. b). Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings suitable for the wash hand basin, including teak wood plug and necessary screwsand making good the disturbed portion, etc., all in sound working condition all as per relevant specification and as directed including all materials, labour, tools,equipments,etc., complete.
128	49. c). Providing and fixing white vitreous china laboratory sink of Size 600x450x200 mm wherever required with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P brass waste and 40mm C.P. brass trap with necessary C.P. brass unions complete, including painting of fittings and brackets, including cutting and making good the wall all in sound working condition all as per relevant specification and as directed including all materials, labour, tools, equipments, etc., complete.
129	49. d). Providing and fixing white glazed fire clay Drain Board of size 600 x 450 x 25mm wherever requiredwith proper aligment /slope to drain the water including C.I. brackets, painting of brackets, cutting and making good the walls all in sound working condition all as per relevant specification and as directed including all materials, labour, tools, equipments, etc., complete.
130	50. Providing and fixing 110mm dia PVC Nahani trap (floor trap with gratings suitable for PVC drainage pipe) embedding the trap making the joints water tight etc., allas directed including allmaterials, labour, tools, equipments etc., complete.
131	51. Providing andfixing PVC gully trap with constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 CS sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in reinforced cement concrete slab 1:1.5:3 mix (1 cement : 1.5 crushed stone sand : 3 graded stone aggregate 20 mm nominal size), including necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 CS sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 crushed stone sand) 12mm thick, finished with a floating coat of neat cement punning @3.3kg/Sqm all as per relevant specification and as directed including cost of cement,all materials, labour, tools, equipments, etc., complete.
132	52. Supplying and fixingChlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply (Trubore / Finolex or equivalent) for internal works exposed on wall with CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing with all required accessories like tees, bends, couplings, elbows, reducers, unions, etc.,jointing of pipes & fittings with one step CPVC solvent cement and testing of joints andincluding punching the masonry/concrete wherever required and making good the disturbed portions, all as per relevant specification and directed at site of work, including cost of cement and all materials, labour, tools, equipments, scaffolding etc., completea) 32 mm dia
133	b) 25mm dia
134	c) 20mm dia
135	53. Supplying and fixingChlorinated Polyvinyl Chloride (CPVC) pipes of 20 mm dia, having thermal stability for hot & cold water supply (Trubore / Finolex or equivalent) for concealed works with CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing with all required accessories like tees, bends, couplings, elbows, reducers, unions, etc.,jointing of pipes & fittings with one step CPVC solvent cement and testing of joints andincluding punching the masonry/concrete wherever required and making good the disturbed portions, all as per relevant specification and directed at site of work,including cost of cement and all labour, tools, equipments, scaffolding etc., completeNote: Necessary Cutting of Brick work, Concrete, Plastering, etc., will be paid under relevant items of BOQ
136	54. Providing, fixing and laying of pipes on floors of, approved quality rigid PVC pipes of 50/75/110mm outside diameters 6 Kgf/sq.cm &4Kgf/sq.cmpressure-(Finolex (or) Trubore (or) Varun (or) Supreme or equivalent) for waste water lines/sewage lines / rain water down fall pipe including necessary specials like bends, tees, elbows, clamps and specials, etc., wherever required, including joining the pipes using necessary adhesives, and making connections to floor traps, gully traps manholes etc., including cutting the floor concrete masonry and making good the disturbed portions all as directed at site of work including all materials, labour, tools, equipments, scaffolding, cement etc., complete.a). 50 mm Dia (6 Kgf/sq.cm)
137	b). 75mm Dia (6 Kgf/sq.cm)
138	c). 110 mm Dia (4 Kgf/sq.cm)
139	d). 110 mm Dia (6 Kgf/sq.cm)
140	55. Supplying and fixing the sanitary fittings with First quality (Parryware/Hindware/ jaquar /Metro or equivalent) C.P Brass / PTMT/ PVC/ SS fittings intoilets in sound working condition including testing etc., all as directed at site of work including all materials, labour, tools, equipments, etc., complete.a). PTMT 600mm Long Towel Rail
141	b). C.P Brass Health faucet 15mm dia. With 1.2M length hose
142	c). C.P Brass Pillar cock 15mm dia
143	d).C.P Brass Short body tap 15mm dia
144	e).C.P Brass Stop cock 15mm dia (Concealed)
145	f). C.P Brass Angle valve 15mm
146	g).C.P Brass Long body Bib cock 15mm
147	h). C.P Brass Extension nipple of size:15mmx50mm
148	i). C.P Brass Shower arm with flange 12\" length
149	j).C.P Brass Shower rose
150	k). C.P Brass 15mm dia. Single lever Wall mixer with telephonic shower
151	l). PTMT 32mm bottle trap- PTMT
152	m). PVC connectionfor wash basin and flush tank -600mm length
153	n). PVC connection for Kohinoor Brand with Nylon thread Hot water line
154	0). Stainless Steel Grating 100mm dia
155	56. Supplying and fixing on wallBevelled edge face mirror (saint Gobain or equivalent) of size 610x450mm(approx) with PVC frames and plywood back all as directed at site of work including all materials, labour, tools, equipments, etc., complete.
156	57. Supplying and fixing of Anodized Aluminium fittings for doors, cup-boards, etc., (anodised transparent or dyed to required shade according to IS: 1868,Minimum anodic coating of grade AC 15) with necessary screws, all as directed at site of work including all materials, labour, tools, equipments, etc. completea). Tower bolt (barrel type) 200x10 mm
157	b). Tower bolt (barrel type) 100x10 mm
158	c). Tower bolt (barrel type) 75x10 mm
159	d). Hook and eye 250mm
160	e). Door handle100mm long with plate 150x32mm
161	f). Butt hinges 125mmlong
162	g). Butt hinges 100mmlong
163	58. Supplying and fixing of brass fittings for doors etc., with necessary screws, etc as directed at site of work including all materials, labour, tools, equipments, etc. completea). Door Stopper with rubber bush (Heavy) with CP brass screw
164	b). Bright finished Brassbutt hinges 125mm
165	c).Bright finished Brass butt hinges 100mm
166	d). Bright finished Brass Tower bolts 150mmlong
167	e). Bright finished Brass handles 125 mm with plate 175x32 mm
168	59. Supplying and fixing of Heavy Duty Stainless steel fittings for doors, etc., with necessary screws, etc as directed at site of work including all materials, labour, tools, equipments, etc. completea). Butt hinges - 125mm.
169	b). Butt hinges - 100mm.
170	c). Tower Bolt / Draw Bolt - 150mm
171	d). Tower Bolt / Draw Bolt - 75mm
172	e). Aldrop 250mm long
173	f). Door handle 125mm long
174	g). Door handle 100mm long
175	h). Magnetic catch for doors/cup boards
176	i). Hook and eyes 150mm long
177	j). Hook and eyes 50mm long
178	60. Providing and applying fibre reinforced elastomeric liquid water proofing membrane with resilient acrylic polymers having Sun Reflectivity Index (SRI) of 105 on top of weathering course roof in three coats @10.76 litre/ 10 sqm. One coat of self-priming of elastomeric waterproofing liquid (dilution with water in the ratio of 3:1) and two coats of undiluted elastomeric waterproofing liquid (dry film thickness of complete application /system not less than 500 microns). The operation shall be carried out after scrapping and properly cleaning the surface to remove loose particles with wire brushes, all as per relevant specification as directed including all materials, labour, tools, equipments, etc., complete.
179	61. Preparing the internal / external surfaces of walls by Removing the existing white or colour wash by scrapping and sand papering and preparing the surface, including applying putty to seal the cracks in the wall wherever required all as directed at site of work including all labour, materials, tools, tackles, equipments, brushes, scaffolding, etc., complete
180	62. Preparing the surfaces of internal walls and applying one coat of primer (Asian / Nippon / Berger or equivalent))of approved brand and colour of good quality to give an even shadehaving low VOC (Volatile Organic Compound ) content all as directed at site of work including all labour, materials, tools, tackles, equipments, brushes, scaffolding, etc., complete
181	63. Preparing the surfaces of existing interior walls / Ceilingsetc., and applyingtwocoatsofColour washing / White washing with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre (Asian / Nippon / Berger or equivalent) of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour all as directed at site of work including all labour, scaffolding, materials, tools, equipments, brushes, safety ladder, safetybelts, safety helmets, etc.,complete.
182	64. Preparing the surfaces of existing external walls /sunshades / wherever required and applyingtwocoatsofColour washing with Exterior emulsion paint having VOC (Volatile Organic Compound ) content less than 50 grams/ litre (Asian / Nippon / Berger or equivalent) of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour all as directed at site of work including all labour, scaffolding, materials, tools, equipments, brushes, safety ladder, safetybelts, safety helmets, etc.,complete.
183	65. Preparing the surfaces of Old Internal walls andpainting with two coats of synthetic enamel paint(colour) (Asian / Nippon / Berger or equivalent) of approved quality to give an even shade, all as directed including all materials, labour, scaffoldings, brushes, tools, equipments, etc., complete.
184	66.Preparing the surfaces of old wooden members and painting with two coats of synthetic enamel paint(Asian / Nippon / Berger or equivalent) of approved quality to give an even shade, all as directed including all materials, labour, scaffoldings, brushes, tools, equipments, etc., complete.NOTE: 1. Necessary painting co-efficient shall be allowed as per ChPA engineering manual.2. The above quantity is inclusive of painting co-efficient.
185	67.Preparing the surfaces of new wooden members and painting with two coats of Deluxe multi surface paint(Asian / Nippon / Berger or equivalent)of approved quality over coat of primer to give an even shade, all as directed including all materials, labour, scaffoldings, brushes, tools, equipments, etc., complete.NOTE: 1. Necessary painting co-efficient shall be allowed as per ChPA engineering manual.2. The above quantity is inclusive of painting co-efficient.
186	68.Preparing the surfaces of old /New steel members and painting with two coats of synthetic enamel paint(Asian / Nippon / Berger or equivalent) of approved quality to give an even shade, all as directed including all materials, labour, scaffoldings, brushes, tools, equipments, etc., complete.NOTE: 1. Necessary painting co-efficient shall be allowed as per ChPA engineering manual.2. The above quantity is inclusive of painting co-efficient.
187	69. Supplying of heavy dutybrass/SS/Aluminium fittings for doors, windows, cupboard etcin sound working condition etc., all as directed at site of work including all materials, labour, tools, equipments, etc., complete.a). Brass cupboard lock 6 lever of approved quality, 75mm size
188	b). Aluminium hanging floor door stopper with twin rubber & stopper
189	c). Stainless steel butt hinges 125x64x1.9mm
190	d). Anodised Aluminium tower bolt (barrel type) 150x10mm
191	e). Anodised Aluminium handles 125mm with plate 175x32mm
192	f). Anodised Aluminium Aldrop 250mm long
193	70. Supplying diluting and injecting chemical emulsion for post constructional anti termite treatment with chlorpyrlphos Emulsifiable concentrate with 1% concentration (i.e. one litre of chemical for every 20 litires of emulsion) in hospital building basement treatment of soil along internal andexternal wall using chemical emulsion at 2.25 litire per linear metre inlcuding drilling and plugging holes etc. and treating the soil under floors, masonry / concrete inside and outside of buildings wherever required, using chemical emulsion at 1 litre per hole at 30cm interval including drilling 12mm dia holes and plugging them with cement mortar 1:2 to the full depth of the hole and treating the points of contact of wood work by chemical emulsion (in oil of kerosene based solution) at 0.5 litres per hole by drilling 6mm dia at downward angle of 45 degree at 150mm c/c and sealing the same and as directed including all material (including cement) labour, tools, scaffolding, ladder, equipments etc. complete
194	71. Removing the existing glass panes in the fixed aluminium frames in aluminium windows wherever required and refixing with new Neoprene/EPDM rubber gasket/ sealeant, aluminium clips using existing glass panes, etc., all as directed at site of work including all labour, scaffolding, materials, tools, equipments, etc.,complete.
195	72. Supplying of Foam board of various sizes for use of signage , identification and name boards whererver required all as directed at site of work including all labour material,tools, equipments, transport,etc.complete.
196	73. Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Clerestory windows & other Frames/Chowkhat of size 45x85mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge and as directed at site of work including transporting, placing, all materials, labour, tools, plants, equipments, fuel, etc., complete.
197	74. Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of required size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge and as directed at site of work including transporting, placing, all materials, labour, tools, plants, equipments, fuel, etc., complete.(Note: stainless steel butt hinges and necessary S.S screws shall be paid separately)
198	75. Providing and fixing First quality UPVC Ball valve to the water pipe lines in all floors in sound working condition including making the joints water tight and testing etc., all as directed at site of work including all materials, labour, tools, equipments, etc., complete.a). 25mm dia
199	b). 32mm dia
200	76. Providing and fixing First quality Gun metal gate valve with CI wheel to the water pipe lines in all floors in sound working conditionincluding making the joints water tight and testing etc., all as directed at site of work including all materials, labour, tools, equipments, etc., complete.a). 20mm dia
201	b). 25mm dia
202	c). 32mm dia
203	77. Engaging of the labours (Coolie) to shifting hospital fixtures / equipments wherever required to the opt places for day to day operation in a safer manner as directed as site including labour, tools, etc., complete.
204	78. Deep cleaning the existing wall tiles, floor tiles and Mosaic tiles wherever required by using harmless chemical solution and as per manufactures specification all as directed including all labour, tools, equipments, chemical etc. complete.
205	79. Removing, rolling, stacking and refixing the available mesh gap garware polyster safety materials over hospital buildingall as directed at site of work including all materials, labour, tools, equipments, etc., complete.
206	80. Supplying, fabricating and fixing the M.S gate, window / Ventilator grill, Ladder as per existing or as directed at site using suitable structrual steel as verticles, horizontals and diagonal members,to the reqired length, welding the joints all as directed at site of work andproviding scaffolding, fixing gate in proper alignment, including painting with one coat of red oxide primer on the steel members, all as directed at site of work including cost of cement and all materials, labour, tools, transport, equipments, fuel, etc., complete.Note:1. The payment is based on the total weight of the MS flats, bars, etc., as fabricated. 2. The weighment will made at site or any other place as approved by the engineer-in-charge. Necessary charges for transport, weighment. etc., will be borne by the contractor.
207	81. Providing and fixing 19mm thick both side balancing lamination factory pressed BWP grade marine ply as per IS 710 of approved brand for boxes, shelves, racks, almirah, cupboard and drawer etc. including necessary nails,screws etc.all as directed at site of work including all materials, labour, tools, transport, equipments, fuel, etc., complete.
208	82. Supplying and laying Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 crushed stone sand). Light shade pigment using white cement all as directed at site of work inclulding all labour, tools, tackles, equipments, fuel transport, etc. complete.
209	83. a). Hire charges for Tractor with trailor forshift basis (8 hours) for conveying unwanted materials steel/ wooden / Rubber materials/leavesetc to RSO yard /dumping yard with Labour Engaged for lifting the scraps etc..,Loading and unloading materials etc., all as directed at site of work inclulding all labour, tools, tackles, equipments, fuel transport, etc. complete.Note : The required labour will be supplied under relevant item in BoQ.
210	b). DeploymentofLabour (Coolie)(3Nos/shift) and engaged 10 shifts
211	84. Operating of vehicle mounted Heavy duty jetting cum suction machine including diesel with driver and operator for cleaning sewer lines, septic tank, manholes including loading and disposing the wastewherever required as directed at site including all labour, tools, equipments, transport, fuel, etc., complete.Note: 1. For handling/cleaning the machine, the cost of labour charges will be bone by the contractor.2. The required water will be given in the near by site area at free of cost.3. The rate shall be inclusive of diesel, all tools and plants etc., complete.4. The contractor has not claim any charge for damaged parts. 5. The unwanted materials like silt or any garbage to be dumped at open area as directed by the department.6. If any Break down or labour problem during working time deduction will be calculated proportionately based on the rate per day/per hour.
212	85. Dewatering using 10 HP diesel engine pumpset including Hire charges, cost of Diesel, Engine oil, pump operator, labour charges, conveyance of pumpset and fuel to site and back, loading, unloading and any other incidental charges wherever required as directed at site including all labour, tools, equipments, transport, fuel, etc., complete.
213	86. Providing and fixing chromium plated brass curtain rod having wall thickness of 1.25mm with two chromium plated brass brackets fixed with C.P. brass screws and PVC sleeves etc., all as directed at site of work including all labour,materials, tools, equipments, etc.,complete.
214	87. Supplying and fixing20mm dia PVC Pipe for AC water drain outlet, with all required accessories like tees, bends, couplings, elbows, reducers, unions, etc.,jointing of pipes & fittings with PVC solvent and testing of joints andincluding cutting the masonry/concrete wherever required and making good the disturbed portions, all as per relevant specification and directed at site of work,labour, tools, equipments, scaffolding etc., completeNote: Necessary Cutting of Brick work, Concrete, Plastering, etc., will be paid under relevant items of BOQ.
215	88. a). Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames.
216	b). Providing and fixing factory made uPVC glazed/wire mesh windows/doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge. Wire mesh / Glazing of plain/ toughened/ laminated/ double glass unit with / without high performance coatings as per design requirements and conforming to IS: 3548 & IS: 16231 shall be paid separately. Fixed window / ventilator with mullion / transom.Using R4 series with frame (64mm & above ) x (50mm & above) & mullion (64mm & above) x (70mm & above). (Height above 2.5 metre)Note: Glass area will be measured and paid separately as per relevant BoQ.
217	89. Providing and fixing factory made uPVC glazed/wire mesh windows/doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge. Wire mesh / Glazing of plain/ toughened/ laminated/ double glass unit with / without high performance coatings as per design requirements and conforming to IS: 3548 & IS: 16231 shall be paid separately. Three track three panels sliding window with Aluminium channel for roller track, wool pile, nylon rollers with SS 304 body.Using R3 series with frame (98mm & above) x (40mm & above) & sash (30mm & above) x (55mm & above) with zinc alloy (zamak) powder coated handle on two end panels along with multi-point locking system (Height upto 1.8 metre).Note: Glass area will be measured and paid separately as per relevant BoQ.
218	90. Providing and fixing factory made uPVC glazed/wire mesh windows/doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge. Wire mesh / Glazing of plain/ toughened/ laminated/ double glass unit with / without high performance coatings as per design requirements and conforming to IS: 3548 & IS: 16231 shall be paid separately. Two and half track three panels sliding window with two glazed & one wire mesh panels with Aluminium channel for roller track, wool pile, nylon rollers with SS 304 body. Using R2 series with frame (65mm & above) x (40mm & above) & glazed sash (25mm & above) x (50mm & above) & fly screen sash (18mm & above) x (40mm & above) with zinc alloy (zamak) powder coated touch locks with hook (Height upto 1.2 metre). Note: Glass area will be measured and paid separately as per relevant BoQ.
219	91. Providing and fixing good quality polyester fabric (washable) vertical blinds (100mm wide) with anodized aliminium top rails, wheels in poly carbonate runners for smooth movement and self adjustable unbreakable Teflon spacers, trouble free control unit, bottom chain, fitting chain galvanised steel bottom weight, abord weight including all accessories etc. all as directed including all materials, labour, tools, equipments, scaffolding etc. complete.
220	92. Providing and fixing good quality non - reflective type sun control film (Garware or equivalent) of thickness 50mm microns to the glasspanels of the partition / doors / windowsincluding thoroughly cleaning the glass panels and removing the stain if any, with good quality soap or liquid detergents, removing any other foreign particles etc., all as directed including all materials, labour, tools, etc., complete.
221	93. Engaging of labour for removal of unwanted vegetation growth in all floors of the building wherever requiredall as directed including labour, materials, tools, equipments, transport, fuel, etc., complete.
222	94. Providing and laying Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1:4 (1 cement : 4 CS sand), 25mm thick all as directed including all materials, labour, tools, etc., complete.
223	95. Providing and laying 40mm thick granolithic flooring in C.C. 1:2:4 in volumetric proportions (1 cement : 2 crushed stone sand : 4 hard granite graded stone aggregate 12.5mm nominal size) including finishing coat of neat cement at 2.20Kg/m2, including mixing, transporting, placing ramming, consolidating, curing,etc.,all as directed includingcement and all othermaterials, labour,tools, equipments, etc. complete.
224	96. Providing and fixing SFRC (Steel Fiber Reinforced Concrete) Manhole cover with frame of size as directed for Manhole and wherever required in mix 1:1.5:3 ( 1 cement : 1.5 C.S.sand : 3 hard granite graded stone aggregate of 20mm nominal size) in volumetric proportions to the required size, all as per relevant specifications, drawings and as directed includingnecessary form work, mixing, transporting, placing, compacting, curing, finishing the exposed concrete surface withneat cement punning at 2.2 kg/Sq.m as directed, including lifting, handling, transporting and placing the cover over the frame in correct position and alignment, providing necessary lifting holes including all materials, labour, tools, plants, equipments, fuel, etc., complete.a). 900mm x 900mm
225	b). 600mm x 600mm
226	97. Supplying and fixing of good quality insects preventing PVC netlon mesh without country weed reepers consisting of 1.8mm X1.8mm apexture for size (Approx) to the window openings andventilators etc., and wherever required after removing the old damaged mesh including providing 25mm wide hook fasteners nailed stabled continuously on all the four sides of the existing upvc frames with suitable hook and loop fasteners tailored on the edges of the screen all of approved quality and as directed at site of work including all labours, materials, fabrication, tools, equipments, scaffoldings, etc., complete.
227	98. Removing the exisitng wornout Aluminium sliding door and re-placing with UPVC (Un-Plasticized Polyvinyl Chloride) Two track two panels sliding door with Aluminium channel for roller track, wool pile, zinc alloy (zamak) powder coated handle on every panel along with multi-point locking system, adjustable nylon rollers with SS 304 body Using R4 series with frame (64mm & above) x (45mm & above) & sash (44mm & above) x (85mm & above). (Height above 2.5 metre) all as directed at site of work including all labours, materials, fabrication, tools, equipments, scaffoldings, etc., complete.
228	99. Removing wornout GI pipe outlet / delivery pipe embedded in the RCC Over head tank above staircase Head room and Providing and fixingGI pipe / Gun Metal Gate Valve for Delivery / Washout pipe all as directed at site of work including all labours, materials, fabrication, tools, equipments, etc., complete.Note: Necessary Cutting of RCC, laying of concrete and finishing with CM 1:3, 20mm thick with admixtures etc., will be paid under relevant items of BOQ.a). 50mm dia GI Pipe
229	b). 50mm dia Gate Valve (Heavy Duty)
230	100. Loading, transporting, dumping and leveling the surplus earth and debris etc., within a lead of 3kms out side the Port premises all as per relevant specifications and as directed including all labour, transport, tools, equipments, fuel, etc., complete. Note:1.The tenderer shall maintain trip sheets in triplicate in ChP\"s approved format at his own cost.2.Payment will be based on the lorry cubical content. No deduction of voids for debris will be made. 4. 20%deduction of voids for surplus earthwill be made. However the final quantity will be restricted to actual quantity of debris dismantling /demolishing items.(a) Surplus Earth
231	b). Debris
232	Schedule- A3Electrical work
233	1).Supply and Install / Replacing of Electric Flying Insect Killer Machine 2 feet. Wall Mounted or Free Standing - Hanging Chain Included Removable Catchment Tray For Dead Insect Bodies, Easily Cleanable Without Insect Contact as per Schedule ‘A’.
234	2.Supply and Install / Replacing of Distribution Board – I comprising of 1 No 125A 4P 25 kA MCCB as incomer 2 Nos 63A TP MCB, 6 Nos 32A SP MCB, 12 Nos 20A SP MCB, 12 Nos 16A SP MCB, \"B\" Series MCB and 9 Nos 10A SP MCB, \"B\" Series MCB as outgoing with suitable copper wires / busbar for each phase and neutral connection with earth link and all other components and accessories as per Schedule ‘A’.
235	3.Supply and Install / Replacing of Distribution board - II shall be comprising with suitable way of 1 No 100 A 4P, 25 kA MCCB as incomer and 2 Nos 63A TP MCB, 3 Nos 32A SP MCB, 6 Nos 20A SP MCB, 6 Nos 20A SP MCB, \"C\" Series MCB12 Nos 16A SP MCB, \"B\" Series MCB and 12 Nos 10A SP MCB, \"B\" Series MCB as outgoing with suitable copper wires / busbar for each phase and neutral connection with earth link and all other components and accessories as per Schedule ‘A’.
236	4.Supply and Install / Replacing of Distribution Board - III comprising of 1 No 63A, 4P, MCCB as incomer and 2 Nos 32A TP MCB, 12 Nos 20A SP MCB, \"C\" Series MCB and 12 Nos 10A SP MCB, \"B\" Series MCB as outgoing with suitable copper wires / busbar for each phase and neutral connection with earth link and all other components and accessories as per Schedule ‘A’.
237	5.Supply and Install / Replacing of Distribution Board – IV comprising of 1 No 63A 4P MCCB as incomer and 1 Nos 32A TP MCB, 3 Nos 20A SP MCB, 9 Nos 16A SP MCB, \"C\" Series MCB and 9 Nos 10A SP MCB, \"B\" Series MCB as outgoing with suitable copper wires / busbar for each phase and neutral connection with earth link and all other components and accessories as per Schedule ‘A’.
238	6.Supply of 4 Feet 2 X 20w Box type LED BOX TYPE FITTING with T8 LED Tube light with SINGLE SIDE connection and all other accessories as per Schedule ‘A’.
239	7.Supply of 4 Feet 1 X 20w Box type LED BOX TYPE FITTING with T8 LED Tube light with SINGLE SIDE connection and all other accessories as per Schedule ‘A’.
240	8.Installation Surface/ Recessed of 4 Feet BOX TYPE FITTING light fitting with suitable down rods, brackets as per Schedule ‘A’.
241	9.Supply of suitable Down Rod for 4 Feet Tube Light Fittings as per Schedule ‘A’.
242	10.Supply of 2 Feet 10 W Moulded type MIRROR LED Fittings with all connections other accessories as per Schedule ‘A’.
243	11.Installation of above Moulded type LED Mirror light fittings as per Schedule ‘A’.
244	12.Supply of recess type diffused LED 20 W Bulk Head light fitting suitable for 220V, full bright at various locations as per Schedule ‘A’.
245	13.Installation of Bulk Head light fittings as per Schedule ‘A’.
246	14.Supply and Install LED 0.5 W BULB FOR B22 holder suitable for 220V, full bright at various locations as per Schedule ‘A’.
247	15.Supply and Install / Replace of recess type diffused LED 7\" round 12 W light fitting WITH BULB suitable for 220V, full bright at various locations as per Schedule ‘A’.
248	16.Supply and Install / Replacing to be mount in the Surface/ Recessed 220V CALLING BELL with 6 different sounds along with base plates Junction Box and ceiling rose including terminations for all units. including supply of modular switch boxwith all other accessories etc. as per Schedule ‘A’.
249	17.Supply and Install / Replace of one number 63A FP, MCCB with suitable connections and Metal type ENCLOSURE (\"C\" series MCCB) at various locations as per Schedule ‘A’.
250	18.Supply and Install / Replace of one number 32A FP, MCCB with suitable connections and Metal type ENCLOSURE (\"C\" series MCCB) at various locations as per Schedule ‘A’.
251	19.Supply and Install / Replace of one number 32A DP, MCB with suitable connections and Metal type ENCLOSURE (\"C\" series MCB) at various locations as per Schedule ‘A’.
252	20.Supply and Install of one number 16A/20A DP, MCB with suitable connections and Metal type ENCLOSURE (\"C\" series MCB) at various locations as per Schedule ‘A’.
253	21.Supply and Install / Replace of one number 32A DP, MCB with suitable connections on the EXISTING Metal type ENCLOSURE / DB (\"C\" series MCB) at various locations as per Schedule ‘A’.
254	22.Supply and Install / Replace of one number 20A SP, MCB with suitable connections on the EXISTING Metal type ENCLOSURE / DB (\"C\" series MCB) at various locations as per Schedule ‘A’.
255	23.Supply and Install / Replace of one number 16A SP, MCB with suitable connections on the EXISTING Metal type enclosure / DB (\"C\" series MCB) as at various locations as per Schedule ‘A’.
256	24.Supply and Install / Replace of one number 10A SP, MCB with suitable connections on the EXISTING Metal type ENCLOSURE / DB (\"B\" series MCB) at various locations as per Schedule ‘A’.
257	25.Supply and Installation / Replace of 6 Way Metal Box Enclosure as per Schedule ‘A’.
258	26.Supply and Installation / Replace of 8 Way Metal Box Enclosure as per Schedule ‘A’.
259	27.Supply and Install / Replace Surface/ Recessed of all materials and accessories for 16A/15A MODULAR type switch and socket outlet along with base plates, FRAME AND WITH SUITABLE BOX connections as per Schedule ‘A’.
260	28.Supply and Install / Replace Surface/ Recessed of all materials and accessories for 2 Nos 5A MODULAR type switch and socket outlet along with base plates, FRAME AND with SUITABLE BOX connections as per Schedule ‘A’.
261	29.Supply and Install / Replacing to be mount in the Surface/ Recessed switch board of all materials of 5 Amps Modular Switch and Socket outlet to be mounted in the modular type Sub Switch Board itself, including base plates, FRAME and wiring to the plug as per Schedule ‘A’.
262	30.Supply and Install / Replacing to be mount in the Surface/ Recessed switchboard of all materials of 5 Amps modular switch including supply of modular switch box with all other accessories to control of fan, light etc. as per Schedule ‘A’.
263	31.Supply and Install / Replacing to be mount in the Surface/ Recessed switchboard of all materials of 5 Amps MODULAR Bell push switch including supply of modular switch boxwith all other accessories to control of fan, light etc. as per Schedule ‘A’.
264	32.Supply of 1200 MM, brown colour sweep Ceiling fan, with wide blades, suitable down Rod, electronic regulator and all other accessories as per Schedule ‘A’.
265	33.Installation of Ceiling fan as per Schedule ‘A’.
266	34.Supply of suitable Down Rod for Ceiling fan with as per Schedule ‘ A’.
267	35.Supply of 450 mm sweep, Wall mounting fan with polypropylene plastic blade, powder coated metal body and guards with speed control and all other accessories as per Schedule ‘A’.
268	36.Supply of 400 mm sweep, Wall mounting fan with polypropylene plastic blade, powder coated metal body and guards with speed control and all other accessories as per Schedule ‘A’.
269	37.Installation of above Wall mounting fans as per Schedule ‘A’.
270	38.Supply of 450 mm sweep, Pedestal fan with polypropylene plastic blade, powder coated metal body and guards with speed control and all other accessories as per Schedule ‘A’.
271	39.Supply of 18” size of Exhaust fan with necessary clamps and accessories for all units as per the technical specifications as per Schedule ‘A’.
272	40.Installation of above Exhaust fan as per Schedule ‘A’.
273	41.Supply of 15” size of Exhaust fan with necessary clamps and accessories for all units as per the technical specifications as per Schedule ‘A’.
274	42.Installation of above Exhaust fan as per Schedule ‘A’.
275	43.Supply of 12” size of Exhaust fan with necessary clamps and accessories for all units as per the technical specifications as per Schedule ‘A’.
276	44.Installation of above Exhaust fan as per Schedule ‘A’.
277	45.Supply of 9\"\" size of Exhaust fan with necessary clamps and accessories for all units as per the technical specifications as per Schedule ‘A’.
278	46.Installation of above Exhaust fan as per Schedule ‘A’.
279	47.Supply of 15 litre, 2000 Watts storage water heater with ABS body and PUF insulation as per Schedule ‘A’.
280	48.Installation of above Heater as per Schedule ‘A’.
281	49.Supply of EXTENSION BOX that contains 3 Nos 5A MODULAR type switch and 5 PIN socket along with 5 metre 1.5 sqmm 3 core Workshop flexible copper cable and 5A 3 pin TOP outlet along with Suitable connections as per Schedule ‘A’.
282	50.Supply of EXTENSION BOX that contains 2 Nos 15A/5A MODULAR type switch and 6 PIN socket along with 5 metre 2.5 sqmm 3 core Workshop flexible copper cable and 15A 3 pin TOP outlet along with Suitable connections as per Schedule ‘A’.
283	51.LAYING of 1.25 INCH PVC Pipe in the FLOOR / WALL by CONCEALED. The Contractor shallcut the groove on the wall as per the requirement, after laying the pipe & wire, the same area shall be replaster the groove as per Schedule ‘A’.
284	52Supply and wiring of all materials and accessories to carry out the surface/concealed wiring by using suitable size of PVC conduit /Casing and capping with 2 runs 1.5 Sq.mm and one run 1.0 Sq.mm FRLS PVC insulated unsheathed multistrand copper conductor multistrand wires for Phase, Neutral and Earth. From SSB to Individual PT for Fans, Tube lights etc., through connected junction/ inspection boxes along with modular flush type control switch along with base plates and ceiling rose including terminations wherever necessary as per the technical specifications as per Schedule ‘A’. The Contractor shallcut the groove on the wall as per the requirement, after laying the pipe & wire, the same area shall be replaster the groove.
285	53.Supply and Wiring of all materials and accessories and to carry out the surface/concealed with suitable size of PVC conduit /CASING and Capping wiring by using with 4 runs 10 sq.mm and one run of 6 Sq.mm FRLS PVC insulated unsheathed multistrand copper conductor wires etc., through connected junction/ inspection boxes along with terminations wherever necessary as per Schedule ‘A\". The Contractor shallcut the groove on the wall as per the requirement, after laying the pipe & wire, the same area shall be replaster the groove.
286	54.Supply and Wiring of all materials and accessories and to carry out the surface/concealed with suitable size of PVC conduit /CASING and Capping wiring by using with 4 runs 6 sq.mm and one run of 4 Sq.mm FRLS PVC insulated unsheathed multistrand copper conductor wires etc., through connected junction/ inspection boxes along with terminations wherever necessary as per Schedule ‘A\". The Contractor shallcut the groove on the wall as per the requirement, after laying the pipe & wire, the same area shall be replaster the groove.
287	55.Supply and Wiring of all materials and accessories and to carry out the surface/concealed with suitable size of PVC conduit /CASING and Capping wiring by using with 4 runs 4 sq.mm and one run of 2.5 Sq.mm FRLS PVC insulated unsheathed multistrand copper conductor wires etc., through connected junction/ inspection boxes along with terminations wherever necessary as per Schedule ‘A\". The Contractor shallcut the groove on the wall as per the requirement, after laying the pipe & wire, the same area shall be replaster the groove.
288	56.Supply and Wiring of all materials and accessories and to carry out the surface/concealed with suitable size of PVC conduit /CASING and Capping wiring by using with 2 runs 6 sq.mm and one run of 4 Sq.mm FRLS PVC insulated unsheathed multistrand copper conductor wires etc., through connected junction/ inspection boxes along with terminations wherever necessary as per Schedule ‘A\". The Contractor shallcut the groove on the wall as per the requirement, after laying the pipe & wire, the same area shall be replaster the groove.
289	57.Supply and Wiring of all materials and accessories and to carry out the surface/concealed with suitable size of PVC conduit /CASING and Capping wiring by using with 2 runs 4 sq.mm and one run of 2.5 Sq.mm FRLS PVC insulated unsheathed multistrand copper conductor wires etc., through connected junction/ inspection boxes along with terminations wherever necessary as per Schedule ‘A\". The Contractor shallcut the groove on the wall as per the requirement, after laying the pipe & wire, the same area shall be replaster the groove.
290	58.Supply and Wiring of all materials and accessories and to carry out the surface/concealed with suitable size of PVC conduit /CASING and Capping wiring by using with 2 runs 2.5 sq.mm and one run of 1.5 Sq.mm FRLS PVC insulated unsheathed multistrand copper conductor wires etc., through connected junction/ inspection boxes along with terminations wherever necessary as per Schedule ‘A\". The Contractor shallcut the groove on the wall as per the requirement, after laying the pipe & wire, the same area shall be replaster the groove.
291	59.Supply and Wiring of all materials and accessories and to carry out the surface/concealed with suitable size of PVC conduit /CASING and Capping wiring by using with 2 runs 1.5 sq.mm and one run of 1.0 Sq.mm FRLS PVC insulated unsheathed multistrand copper conductor wires etc., through connected junction/ inspection boxes along with terminations wherever necessary as per Schedule ‘A\". The Contractor shallcut the groove on the wall as per the requirement, after laying the pipe & wire, the same area shall be replaster the groove.
292	60.Supply of 4 core 25 Sq.mm L.T. underground cable of 1100 V galvanized steel strip armoured XLPE cable with stranded Aluminium conductorconforming to IS 7098 Part I 1985 with latest amendments with ISI mark for various locations as per Schedule ‘A’.
293	61.Laying of the cable on the wall by Alu. Clamping with equal intervals with all other accessories as per Schedule ‘A’.
294	62.Laying of the cable of through on the tray as per Schedule ‘A’.
295	63.Supply of 4 core 16 Sq.mm L.T. underground cable of 1100 V galvanized steel strip armoured XLPE cable with stranded Aluminium conductorconforming to IS 7098 Part I 1985 with latest amendments with ISI mark for various locations as per Schedule ‘A’.
296	64.Laying of the cable on the wall by Alu. Clamping with equal intervals with all other accessories as per Schedule ‘A’.
297	65.Laying of the cable of through on the tray as per Schedule ‘A’.
298	66.Removal of Existing All kind of Cables, Wirings, Light fittings, all kind of Fans, Panels and DBs as per Schedule ‘A’.
299	Schedule- A4 Electronics & Communication-Telephone Communication work,
300	1). Supply of 50 pair 0.5 mm copperunarmoured PVC cablePreferred make : Finolex / PolyCab/Legrand
301	2). Supply of 20 pair (15 mm copper unarmoured PVC cablePreferred make : Finolex /PolyCab/Legrand
302	3). Supply of 5 pair 0.5 mm copper unarmoured PVC cable Preferred make : Finolex I PolyCab/Legrand
303	4). Supply and Laying of size PVC casing & capping for the laying 50 pair 0.5 mm copper unarmoured PVC cable inside the cabin
304	5). Supply and Laying of 1 1/2\" size PVC casing & capping for the laying 20 pair 0.5 mm copper unarmoured PVC cable inside the cabin
305	6). Supply and Laying of 1\" size PVC casing & capping for the laying 5 pair 0.5 mm copper unarmoured PVC cable inside the ca in
306	7). Supply and Installation of Krone connector
307	8). Supply of Installation of I/O Box
308	9). Supply and Installation of 50 pair junction box with Krone Connector
309	Schedule- A5 Electrical- Power supply work,
310	1). Charges for Dismantling, Removal, Loading, Transporting, Dumping of old, reduntant various Alu power cables and LT panels etcfrom Hospital complex to RSD
311	2). Supply & Laying of 4core 70, Aluminium conductor XLPE L.T. cablea). Supply
312	b). Laying Inconcrete trench
313	c). Laying on cable Tray
314	d). Laying Underground
315	e).End termination for 4Core x 70
316	3). Supply & Laying of 3.5 core 185, Aluminium conductor XLPE L.T. cablea). Supply
317	b). Laying Inconcrete trench
318	c). Laying on cable Tray
319	d). Laying Underground
320	e). End termination for 3.5 x 185
321	4). Supply & Laying of 3.5c150sqmm LT Alu cablea). Supply
322	b). In concrete trench
323	c). On FRP cable tray
324	d). Under ground
325	e). End termination
326	5). Supply & Laying of 4c95 sqmm LT Alu cablea). Supply
327	b). Laying in Concrete trench
328	c). On FRP cable tray
329	d). Underground
330	e). End termination
331	6. Supply& laying of 4core 50 square mm alu xlpe lt cablea). Supply
332	b). Laying in Concrete trench
333	c). On FRP cable tray
334	d). Under Ground
335	e). End termination 4core 50sqmm
336	7. Supply& laying of 4core 25 square mm alu xlpe lt cablea). Supply
337	b). Laying in Concrete trench
338	c). On FRP cable tray
339	d). Under ground
340	e). End termination 4core 25
341	8. Supply& laying of 4core 16 square mm alu xlpe lt cablea). Supply
342	b). Laying in Concrete trench
343	c). On FRP cable tray
344	d). Under ground
345	e). End termination 4c16sqmm
346	9. Supply installation testing commsioning of wall mountedLT Panel -I comprising250Amps 4 pole incomer MCCB and 3 NoS 100AmPs MCCBas out goinga). Supply
347	b). Installation Testing commissioning
348	10). Supply installation testing commsioning ofwall mounted LT Panel -II comprising 2 nos 400 Amps 4p MCCB as incomers, 10 Nos 100Amps, 4p,MCCBS, 1 Nos. 250A MCCB 4P as out going feedersa). Supply
349	b). Installation Testing commissioning
350	11). Supply installation testing commsioning of wall mounted LT Pane-III comprising 630 Amps 4p MCCB as incomer and 8 Nos 100A 4p MCCB and 6 Nos 63A 4P MCCB as outgoing feedersa). Supply
351	b). Installation Testing commissioning
352	12). Supply installation testing commsioning ofFloor Mounted LT feeder pillar outdoor with250Amps 4P MCCB as Incomer and 6 nos 100A 4p MCCB 6 nos 63A 4P MCCB as outgoinga). Supply
353	b). Installation Testing commissioning
354	13). Supply installation testing commsioning of wall mounting LT Panel -IV comprising 250Amps MCCB as incomer, and1 no 100A MCCB 8 Nos 63 amps 4p mccb as outgoinga). Supply
355	b). Installation Testing commissioning
356	14). Charges for Rerouting of various size LT cables 16 sqmm to 300 sqmm including dis connection and reconnectiona). In trench
357	b). FRP cable tray
358	c). Underground
359	15). Supply and Mounting of FRP cable Tray Ladder Type 600 mm widtha). Supply
360	b). Mounting along the wall with Angle Grouting
361	16). Supply and Mounting of FRP cable Tray Ladder Type 300 mm widtha). Supply
362	b). Mounting along the wall with Angle Grouting
363	17). Supply & mounting FRP cable TRAY ladder type 150mm widtha). Supply
364	b). Mounting along the wall with Angle Grouting
365	18). Supply & Mounting of cone type FRP junctions for 500 mm to 300mm traya). Supply
366	b). Mounting along the wall with Angle Grouting
367	19). Supply & Mounting of cone type FRP junctions for 500 mm tray to 150mma). Supply
368	b). Mounting along the wall with FRP/MS Angle Grouting
369	20). Supply & Mounting of cone type FRP junctions for 300 mm tray to 150mma). Supply
370	b). Mounting along the wall withMS/FRPAngle Grouting
371	21). SITC of Permanent Earth Electrodea). Supply
372	b). Installation Testing commissioning
373	22). Supply & laying of GI Earth Strip 40mm*5mma). Supply
374	b). Laying and interconnecting
375	23). Supply & laying of GI Earth Strip 25mm*6mma). Supply
376	b). Laying and interconnecting
377	24). SITC of AC DBs with 100A MCCB 4P as Incomer and 16 Nos 20A DP MCB as outgoinga). Supply
378	b). Installation Testing commissioning
379	25). Supply and Laying of GI earthwire 8 SWGa). Supply
380	b). Laying
381	26). Supply and providing cable Joints for various size LT cablesa). Supply of Joint Kit 3.5.Core 185 Sqmm
382	b). Providing Joint
383	c). Supply of Joint Kit 3.5.Core 150 Sqmm
384	d). Providing Joint
385	e). Supply of Joint Kit for 4x95,4x70, 4x50, 4x25, 4x16 cables (2 Nos. Each)
386	f). Providing Joint for above cables
387	27). Supply& Installation of 100KVAR AFC panel,indoorFloor Mounted , Top side Cable Entry 415V, 3-phase, 50Hz microcontroller-based APFC relay for automatic power factor correction, capacitor duty contactors, individual MCB protection for each capacitor bank, a current transformer (CT) for accurate current sensing, and a digital display for parameters like voltage, current, and power factor. The panel will also have specific features such as auto/manual mode, screen hold, and overload protectionwith 200A,50KA, 4P MCCB as incomera). Supply
388	b). Installation Testing& commissioning
389	Schedule- A6-Air Condition with CAMC
390	ITEM – I Supply and Installation1). Cost for supply of Non Inverter Type 2 TR capacity 3 star rated slim high wallmounting type split air conditioner along with all requiredmaterials and accessories, as per schedule ‘A’.
391	2). Cost for installation of Non Inverter Type 2 TR capacity 3 star rated slim high wall mounting type split air conditioner, as per schedule ‘A’
392	ITEM – IICAMC for 5 yearsCharges for Comprehensive Annual Maintenance Contract for 25 Nos. 2 TR, 3 Star rated Split Air Conditioners at various locationNote: The CAMC rate is per unit per month.During the CAMC period the firm shall do servicing of Air Conditioners in a period of 3 months (i.e., 4 times in a year for each AC) and attending break down calls as and when informed by Engineer-in-Charge)a). 1st Year
393	b). 2nd year
394	c). 3rd year
395	d). 4th Year
396	e). 5th Year
397	Schedule- A7 Pipeline Works
398	Medical Block:1). Supply and fixing of CPVC Pipeline 50mm dia, Trubore/ Finolex or equivalent (Internal work exposed on wall) wherever necessary including cost of fittings, fixing the pipe with clamps at 1.00m spacing all as directed at site of work including all labour, tools, equipment, etc. complete.
399	2). Supply and fixing of CPVC Pipeline 25mm dia, Trubore/ Finolex or equivalent (Internal work exposed on wall ) wherever necessary Including cost of fittings all as directed at site of work Including all labour, tools, equipment, etc. complete.
400	3). Supply and fixing of CPVC Pipeline 25mm dia, Trubore/ Finolex or equivalent (Concealed work, including cutting chases and making good the walls etc.) wherever necessary Including cost of fittings, fixing the pipe with clamps at 1.00m spacing all as directed at site of work Including all labour. tools, equipments, etc. complete.
401	4). Supply and fixing of CPVC Pipeline 20mm dia, Trubore/ Finolex or equivalent (Concealed work, including cutting chases and making good the walls etc.) wherever necessary including cost of fittings, the pipe with clamps at 1.00m spacing all as directed at site of work including all labour, tools, equipments. etc. complete.
402	Surgical Block:5). Supply and fixing of CPVC Pipeline 50mm dia, Trubore/ Finolex or equivalent (Internal work exposed on wall) wherever necessary including cost of fittings, fixing the pipe with clamps at 1.00m spacing all as directed at site of work including all labour, tools, equipment, etc. complete.
403	6). Supply and fixing of CPVC Pipeline 25mm dia, Trubore/ Finolex or equivalent (Concealed work, including cutting chases and making good the walls etc.) wherever necessary Including cost of fittings, fixing the pipe with clamps at 1.00m spacing all as directed at site of work Including all labour. tools, equipments, etc. complete.
404	7). Supply and fixing of CPVC Pipeline 20mm dia, Trubore/ Finolex or equivalent (Concealed work, including cutting chases and making good the walls etc.) wherever necessary including cost of fittings, the pipe with clamps at 1.00m spacing all as directed at site of work including all labour, tools, equipments. etc. complete.
405	8). Supply and fixing of G I. pipeline 50mm dia (C-Class) (Internal work exposed on wall) complete with GI fittings and clamps at1.00m spacing,including cutting chases and making good the walls wherever necessaryall as directed at site of work Including all labour, tools, equipments, etc. complete
406	9). Supply and fixing of G I. pipeline 50mm dia (C-Class) (External work) complete with 0.1. fittings, including trenching and refilling etc. wherever necessary all as directed At site of work including labour, tools, equipments, etc., complete
407	10). Supply and fixing of 2\" Gun Metal Non-Return Valve(Horizontal)
408	11). Supply and fixing of 2\" Gun Metal Gate Valve
409	12). Supply and fixing of 3/4\" CPVC Ball Valve
410	13). Supply and fixing of I CPVC Ball Valve
411	14). Dismantling of existing pipeline PVC / UPVC/G.I. of sizes 3/4\" Dia , 1\" Dia and 2\" Dia and shifting to RSA Yard
412	RO WATER PIPELINES15). Supply and fixing of CPVC Pipeline 25mm dia, Trubore/ Finolex or equivalent (Concealed work, including cutting chases and making good the walls etc.) wherever necessary including cost of fittings, fixing the pipe with clamps at 1.00m spacing all as directed at site of work including all labour, tools, equipments, etc. complete
413	16). Supply and fixing of 1\" - CPVC Ball Valve
414	Schedule- A8 Replacement of Gas pipeline to Kitchen
415	1). Supplying and fixing ofstainless steel 304 Grade 12 mm dia seamless pipeincluding valve, manifold, flexiable tubes, etc and connection with cooking equipments including fixing in proper positionall as directed at site of work including all labour, tools, equipment, etc. complete.
416	Schedule- A9 Replacement of Oxygen pipeline system-(i) Medical Block
417	1). Medical Gas Copper Pipeline arrangement to hang on the wall of socket type connection installation of seamless cleaned and degreased non arsenical phosphorous gas copper pipe line with saddles complete with brazing work including all copper fitting (tee, elbow, reducer, coupling). The copper pipelines should be tested suitable for a steam of working pressure of 17.34 kg. / cm2 (17 bar) and confirm to BS 864 Standard with specially made for brazed socket type connection. The medical gas copper pipeline should be tested as per standard and commissioning after painting as per International Code No. IS 2379/1963 Table-V. The pipelines installed at the various wings and floors etc., complete as directed by the Departmental Officers as per IS Code 12827 / 1989 & ISO 7396 / 1987 Specification. (i)76mm OD X 1.5mm thick
418	ii).42mm OD X 1.2mm thick
419	iii).28mm OD X 0.9mm thick
420	iv).22mm OD X 0.9mm thick
421	v).15mm OD X 0.9mm thick
422	vi).12mm OD X 0.9mm thick
423	2). SITC of Primary Oxygen Source System.(i)Liquid Medical Oxygen (LMO) tank 3KL
424	2(ii) VIE Vaporizer 300nm3
425	2(iii)Stainless Steel Pipe and Flange Tube Workfrom LMO to VIE Vaporizer
426	2(iv) High Pressuring Regulating System(Working & Standby) for LMO Tank
427	3.SITC of Manifolds ( without Cylinders):(i). Pressure Gauge
428	3(ii). Oxygen manifold arrangements of 2 banks x 20 cylinder each wing with semi automatic control panel which includes contact gauge 2 Nos., outlet pressure gauge, brass heavy duty IO x regulator 2 Nos. with suitable adopter, flexible SS Hose. Mainfold shall be of a construction and of a designs and material suitable for the service pressure in accordance with IS 1282-1989. Emergency alarms with illuminating display for low / high pipeline pressure and malfunctioning of system. 1) Mainfold top frame with provision for connecting 12 cylinders on right bank and 12 cylinders on left bank with high pressure interconnecting copper tubing, silver brazing, non return valve, fasteners and cylinder spport middle angle frame for claping 2 x 12 cylinders and related fasteners. The O2 manifold should with stand a pressure of 140 kg. / CM2. The installation is commissioned after testing as per standards and painted as per International Code and as directed by the Departmental Officers as per IS Code 12827 / 1989 & ISO 7396 / 1987 Specification. -
429	4). SITC of Secondary Oxygen Source System:Digital Fully Automatic Oxygen Control System: 3 Source Control Panel with Primary Ist as liquid with PRS system for liquid oxygen and Secondary as Manifold. The heavy duty control panel to be provided with a flow capacity of approx 2666 LPM at 50 to 60 psi with .CE Certified, ETL Listed / Country of Orgin : Germany.
430	5).Compressed Medical Air System: Supply, installation, testing and commissioning of Compressed Air System of Reciprocating Oil Free Air Compressor Belt Driven Type 10 HP Air Compressor with following provisions. As per IS 12827 / 1987 & ISO 7396 / 1987 Specification Compressor package consists of following: a) 10 HP Air Compressor - 1 No.b) Electric Motor 10 HP - 1 No.c) Dol Starter - L&T - 10 HP - 1 No.d) Base Frame Kit (for Motor and Compressor) - 1 set e) Pressure Swith - 1 No.f) Pressure Gauge - 1 No. g) NRV and Pilot Fittings - 1 No. h) Delivery Tube - 1 Noi) Foundation Bolts & Anchor Fasteners - 1 Lot j) Belt Guard - 1 No.k) Refrigerator Type Air Dryer-40 cfm. capacity-1 No. l) Drain Ball Valve - 1 No.m) Air Outlet Ball Valve - 1 No.Vacuum Room & Air Compressor Room Inside Accessories:Non-Return Valves, Air Pressure Switch, Pressure Gauge, Isolation Valves, Air Filters etc., Inter connecting piping: Mild Steel Pipe of 2 with fittings
431	6).Medical Vacuum SystemSupply, installation, testing and commissioningof Reciprocating Air Cooled Type (10 HP) RatingVaccum Pump as per following provisions.As per IS 12827 / 1987 & ISO 7396 / 1987 Specificationa) Vaccum Pump - 10 HP - 1 No.b) Electric Motor - 10 HP - 1 No.c) DOL Starter with OLR - 1 No.d) Vaccum Switch - 1 No.e) Vaccum Gauge - 1 No.f) Control Frame with Fittings - 1 No.g) Suction Scrubber - 1 No.h) V-Belts - 1 No.i) GI & MS Fittings - 1 No.j) Brass Fittings - 1 No.k) Exhaust Silencer - 1 No.i) Base Frame for Motor and Vaccum Pump - 1 setm) Pilot Line with Fittings - 1 set,Vaccum Room & Air Compressor Room Inside
432	7). SITC of ISOLATION CONTROL VALVE: Brass Isolation Valve suitable for the copper pipe and should be of non lubricated 90 degree turn lever ball valve of reputed make, conneced in line with medical gas pipe line system by using suitable size brass valve adopter union, ferrule, nipple, rubber O\" ring, tapion lap and etc. All pipe line regulators shall be capable of controlling pipe line pressure and must compatible with the requirements specified in IS 12827-1989. All valves should be pneumatically tested for twice the working pressure for the gas line as per IS Code 12827 / 1989 & ISO 7396 / 1987 Sepecification. (i) 12 mm ball valve with O-ring Type Both End Adapter
433	ii). 15 mm ball valve with O-ring Type Both End Adapter
434	iii). 22 mm ball valve with O-ring Type Both End Adapter
435	iv). 28 mm ball valve with O-ring Type Both End Adapter
436	v). 42 mm ball valve with O-ring Type Both End Adapter
437	vi). 76 mm ball valve with O-ring Type Both End Adapter
438	8). SITC of Area Valve Service Unit (Valve Unit): Area Valve Service Unit (Alarm & Valve Combo Unit) Area valve box with inbuilt touch screen alarm with sensor kit, NFPA Compliance product combined valve box assembly with alarm & alarm is ETL listed to UL 1069 and CSA C22.2 No 205 signal equipment.(i) 1 Gas -- VALVE -2 SERVICE-ISO (Oxygen and Vacuum)
439	(ii) 2 Gas -- VALVE -2 SERVICE-ISO (Oxygen and Vacuum)
440	(iii) 3Gas -- VALVE -3 SERVICE-ISO (Oxygen, Air 4 Barand Vacuum)
441	9). SITC of Area Alarm Service Unit (Medical Gas Alarm Unit): Area Alarm box with touch screen alarm with sensor kit, HTM02-01 Compliance product combined with Medical Gas Alarm(i) 1 Gas -- VALVE -2 SERVICE-ISO (Oxygen and Vacuum)
442	(ii) 2 Gas -- VALVE -2 SERVICE-ISO (Oxygen and Vacuum)
443	(iii) 3Gas -- VALVE -3 SERVICE-ISO (Oxygen , Air 4 Bar and Vacuum)
444	10). SITC of Terminal Units: DIN / BS Standard Outlet Points with from loading, inner connecting and brass body. Single press inlet with two stage process first stage for patient usage and second stage in parking mode, covered by plastic cover duly colour indicated with specific gas name and non inter changeable for other gases. The cost of materials inclduingtransport, etc., complete, as per standard specification and as directed by the Departmental Officers(i) 1 Gas -- VALVE -2 SERVICE-ISO (Oxygen and Vacuum)
445	(ii) 2 Gas -- VALVE -2 SERVICE-ISO (Oxygen and Vacuum)
446	(iii) 3Gas -- VALVE -3 SERVICE-ISO (Oxygen , Air 4 Bar and Vacuum)
447	11). SITC of Oxygen Flow Meter made up of Brass with Humidifier Bottle Flow Meter should be back pressure compressed and should be accurate gas flow measurement with control range 0-13 litres per minute. It should meet strict permission and dumbling standard. The meter body should be made of brass materials. The humidifier bottle should be made of unbreakable polycorbonate material and auto cleavable at 134 degree centigrate. The rate includes flow meter and its accessories (silicon tube with mask). The cost of materials including transport, etc., complete as per standard specification and as directed by the Departmental Officer and as per IS 12827 / 1989 and ISO 7396 / 1987 Specification
448	12). SITC of Ward Vaccum Unit with Gauge both mounted on a collection jar of capacity 600 ml and with a wall bracket for mounting it on the wall. The collecion jar should be made of unbreakable polycarbonate materials which is fully auto cleavable at 134 degree centigrade as per standard specification and as directed by the Departmental Officers and as per IS 12827 / 1989 and ISO 7396 / 1987 Specification. The rate includes cost of silicon hose with SS nipple on either sid
449	13).Medical gas hose : It shall be colour coded for individual services i.e. white for Oxygen, Blue for N2O and Yellow for Vacuum, Black for air. Antistatic rubber tube should be as per ISO standards.
450	14) SITC of Terminal Unit Console Metal Box (i) EGP 1.2mm Thk Metal Powder Coated Box with Printed Aluminium Cover Plate for Single Gas
451	(ii) EGP 1.2mm Thk Metal Powder Coated Box with Printed Aluminium Cover Plate for TWO Gas
452	(iii) EGP 1.2mm Thk Metal Powder Coated Box with Printed Aluminium Cover Plate for ThreeGas
453	(iv) EGP 1.2mm Thk Metal Powder Coated Box with Printed Aluminium Cover Plate for Four Gas
454	Schedule- A9 Replacement of Oxygen pipeline system-(ii) Surgical Block
455	1). SITC of Medical Gas Copper Pipeline arrangement to hang on the wall of socket type connection installation of seamless cleaned and degreased non arsenical phosphorous gas copper pipe line with saddles complete with brazing work including all copper fitting (tee, elbow, reducer, coupling). The copper pipelines should be tested suitable for a steam of working pressure of 17.34 kg. / cm2 (17 bar) and confirm to BS 864 Standard with specially made for brazed socket type connection. The medical gas copper pipeline should be tested as per standard and commissioning after painting as per International Code No. IS 2379/1963 Table-V. The pipelines installed at the various wings and floors etc., complete as directed by the Departmental Officers as per IS Code 12827 / 1989 & ISO 7396 / 1987 Specification.(i)76mm OD X 1.5mm thick
456	ii).42mm OD X 1.2mm thick
457	iii).35mm OD X 1.2mm thick
458	iii).28mm OD X 0.9mm thick
459	iv).22mm OD X 0.9mm thick
460	v).15mm OD X 0.9mm thick
461	vi).12mm OD X 0.9mm thick
462	2.SITC of Manifolds ( without Cylinders):(i). Pressure Gauge
463	2(ii). Oxygen manifold arrangements of 2 banks x 20 cylinder each wing with semi automatic control panel which includes contact gauge 2 Nos., outlet pressure gauge, brass heavy duty IO x regulator 2 Nos. with suitable adopter, flexible SS Hose. Mainfold shall be of a construction and of a designs and material suitable for the service pressure in accordance with IS 1282-1989. Emergency alarms with illuminating display for low / high pipeline pressure and malfunctioning of system. 1) Mainfold top frame with provision for connecting 12 cylinders on right bank and 12 cylinders on left bank with high pressure interconnecting copper tubing, silver brazing, non return valve, fasteners and cylinder spport middle angle frame for claping 2 x 12 cylinders and related fasteners. The O2 manifold should with stand a pressure of 140 kg. / CM2. The installation is commissioned after testing as per standards and painted as per International Code and as directed by the Departmental Officers as per IS Code 12827 / 1989 & ISO 7396 / 1987 Specification
464	2(iii). Oxygen manifold arrangements of 2 banks x 12 cylinder each wing with semi automatic control panel which includes contact gauge 2 Nos., outlet pressure gauge, brass heavy duty IO x regulator 2 Nos. with suitable adopter, flexible SS Hose. Mainfold shall be of a construction and of a designs and material suitable for the service pressure in accordance with IS 1282-1989. Emergency alarms with illuminating display for low / high pipeline pressure and malfunctioning of system. 1) Mainfold top frame with provision for connecting 12 cylinders on right bank and 12 cylinders on left bank with high pressure interconnecting copper tubing, silver brazing, non return valve, fasteners and cylinder spport middle angle frame for claping 2 x 12 cylinders and related fasteners. The O2 manifold should with stand a pressure of 140 kg. / CM2. The installation is commissioned after testing as per standards and painted as per International Code and as directed by the Departmental Officers as per IS Code 12827 / 1989 & ISO 7396 / 1987 Specification
465	2(iv). Supply Of Nitrous Oxide Manifold 2+2 Cylinder With Copper tail pipe, Special NRV, Distance piece, Middle frame With Individual Chain Support, Provision For Fixing Fully-Automatic Control Panel Board with the following items :• Total number for Brass block for NRV – 4 nos.• Total number for Gas pre heater – 4 nos.• Total number of Brass Block for Cylinder Valve – 4 nos.• Non Return Valve - 4 nos.• Cylinder Valve - 4 nos.• Block for regulator – 2 nos.• Double Stage & Double Gauge Regulator – 2 nos.• Middle frame with chain – 4 nos.
466	3). SITC of Oxygen Source System:Digital Fully Automatic Oxygen Control System: 3 Source Control Panel with Primary Ist as liquid with PRS system for liquid oxygen and Secondary as Manifold. The heavy duty control panel to be provided with a flow capacity of approx 2666 LPM at 50 to 60 psi with .CE Certified, ETL Listed / Country of Orgin : Germany.
467	4).SITC of Primary N2O Main Source System: Digital Fully Automatic Nitrous Oxide Control System: 2 Source Control Panel with Primary Ist as liquid and Secondary as Manifold. The heavy duty control panel to be provided with a flow capacity of approx 1500 LPM at 50 to 60 psi with .ETL Listed as per ISO 7396 HTM02-01 standard / Country of Orgin : Germany.
468	5).SITC of Secondary N2O Main Source System: Supply, Installation, Testing, and Commissioning of Single Cylinder Emergency N2O arrangement using a High Flow Double Guage Single Stage Regulator and 3/4\" Control Valve with O-ring Type Adapter for quick release and adopt mechanism using N2O Terminal Unit or NIST with HP Hose,Gas Pre Heater and NRV.
469	6).Compressed Medical Air System: Supply, installation, testing and commissioning of Compressed Air System of Reciprocating Oil Free Air Compressor Belt Driven Type 15 HP Air Compressor with following provisions. As per IS 12827 / 1987 & ISO 7396 / 1987 Specification Compressor package consists of following: a) 15 HP Air Compressor - 1 No.b) Electric Motor 10 HP - 1 No.c) Dol Starter - L&T - 10 HP - 1 No.d) Base Frame Kit (for Motor and Compressor) - 1 set e) Pressure Swith - 1 No.f) Pressure Gauge - 1 No. g) NRV and Pilot Fittings - 1 No. h) Delivery Tube - 1 Noi) Foundation Bolts & Anchor Fasteners - 1 Lot j) Belt Guard - 1 No.k) Refrigerator Type Air Dryer-60 cfm. capacity-1 No. l) Drain Ball Valve - 1 No.m) Air Outlet Ball Valve - 1 No.Vacuum Room & Air Compressor Room Inside Accessories:Non-Return Valves, Air Pressure Switch, Pressure Gauge, Isolation Valves, Air Filters etc., Inter connecting piping: Mild Steel Pipe of 2 with fittings
470	7). Medical Vacuum SystemSupply, installation, testing and commissioning of Reciprocating Air Cooled Type (15 HP) Rating Vaccum Pump as per following provisions. As per IS 12827 / 1987 & ISO 7396 / 1987 Specification a) Vaccum Pump - 15 HP - 1 No. b) Electric Motor - 15 HP - 1 No.c) DOL Starter with OLR - 1 No. d) Vaccum Switch - 1 No.e) Vaccum Gauge - 1 No.f) Control Frame with Fittings - 1 No.g) Suction Scrubber - 1 No.h) V-Belts - 1 No.i) GI & MS Fittings - 1 No.j) Brass Fittings - 1 No.k) Exhaust Silencer - 1 No.i) Base Frame for Motor and Vaccum Pump - 1 setm) Pilot Line with Fittings - 1 set,Vaccum Room & Air Compressor Room Inside
471	8). SITC of ISOLATION CONTROL VALVE: Brass Isolation Valve suitable for the copper pipe and should be of non lubricated 90 degree turn lever ball valve of reputed make, conneced in line with medical gas pipe line system by using suitable size brass valve adopter union, ferrule, nipple, rubber O\" ring, tapion lap and etc. All pipe line regulators shall be capable of controlling pipe line pressure and must compatible with the requirements specified in IS 12827-1989. All valves should be pneumatically tested for twice the working pressure for the gas line as per IS Code 12827 / 1989 & ISO 7396 / 1987 Sepecification(i) 12 mm ball valve with O-ring Type Both End Adapter
472	ii). 15 mm ball valve with O-ring Type Both End Adapter
473	iii). 22 mm ball valve with O-ring Type Both End Adapter
474	iv). 28 mm ball valve with O-ring Type Both End Adapter
475	v). 42 mm ball valve with O-ring Type Both End Adapter
476	vi). 76 mm ball valve with O-ring Type Both End Adapter
477	9). SITC of Area Valve Service Unit (Valve Unit): Area Valve Service Unit (Alarm & Valve Combo Unit) Area valve box with inbuilt touch screen alarm with sensor kit, NFPA Compliance product combined valve box assembly with alarm & alarm is ETL listed to UL 1069 and CSA C22.2 No 205 signal equipment.(i) 1 Gas -- VALVE -2 SERVICE-ISO (Oxygen)
478	(ii) 2 Gas -- VALVE -2 SERVICE-ISO (Oxygen and Vacuum)
479	(iii) 3Gas -- VALVE -3 SERVICE-ISO (Oxygen, Nitrous Oxide,Air 4 Barand Vacuum)
480	10). SITC of Area Alarm Service Unit (Medical Gas Alarm Unit): Area Alarm box with touch screen alarm with sensor kit, HTM02-01 Compliance product combined with Medical Gas Alarm(i) 1 Gas -- VALVE -2 SERVICE-ISO (Oxygen )
481	(ii) 2 Gas -- VALVE -2 SERVICE-ISO (Oxygen and Vacuum)
482	(iii) 3Gas -- VALVE -3 SERVICE-ISO (Oxygen , Nitrous Oxide,Air 4 Bar and Vacuum)
483	11). SITC of Terminal Units: DIN / BS Standard Outlet Points with from loading, inner connecting and brass body. Single press inlet with two stage process first stage for patient usage and second stage in parking mode, covered by plastic cover duly colour indicated with specific gas name and non inter changeable for other gases. The cost of materials inclduing transport, etc., complete, as per standard specification and as directed by the Departmental Officers(i) Oxygen Gas Terminal Unit with Suitable Probe.
484	(ii) N2O Gas Terminal Unit with Suitable Probe.
485	(iii) MA4 Air Gas Terminal Unit with Suitable Probe.
486	(iv) Vacuum Gas Terminal Unit with Suitable Probe.
487	12). SITC of Oxygen Flow Meter made up of Brass with Humidifier Bottle Flow Meter should be back pressure compressed and should be accurate gas flow measurement with control range 0-13 litres per minute. It should meet strict permission and dumbling standard. The meter body should be made of brass materials. The humidifier bottle should be made of unbreakable polycorbonate material and auto cleavable at 134 degree centigrate. The rate includes flow meter and its accessories (silicon tube with mask). The cost of materials including transport, etc., complete as per standard specification and as directed by the Departmental Officer and as per IS 12827 / 1989 and ISO 7396 / 1987 Specification
488	13). SITC of Ward Vaccum Unit with Gauge both mounted on a collection jar of capacity 600 ml and with a wall bracket for mounting it on the wall. The collecion jar should be made of unbreakable polycarbonate materials which is fully auto cleavable at 134 degree centigrade as per standard specification and as directed by the Departmental Officers and as per IS 12827 / 1989 and ISO 7396 / 1987 Specification. The rate includes cost of silicon hose with SS nipple on either side
489	14).Medical gas hose : It shall be colour coded for individual services i.e. white for Oxygen, Blue for N2O and Yellow for Vacuum, Black for air. Antistatic rubber tube should be as per ISO standards..
490	15) SITC of Terminal Unit Console Metal Box (i) EGP 1.2mm Thk Metal Powder Coated Box with Printed Aluminium Cover Plate for Single Gas
491	(ii) EGP 1.2mm Thk Metal Powder Coated Box with Printed Aluminium Cover Plate for TWO Gas
492	(iii) EGP 1.2mm Thk Metal Powder Coated Box with Printed Aluminium Cover Plate for FiveGas
493	16. SITC of Anesthetic Gas Scavenging System:(i) Duplex Anesthetic Gas Scavenging System (AGSS) Duplex blower type with 1 working + 1 standby, AGSS duplex Remote switch flush type and AGSS transfer and hose(3nos)
494	16. (ii) AGSS Duplex remote switch
495	16. (iii) AGSS Gas Outlet Points
496	Schedule- A 10 -(I) Fire Fighting System
497	A. FIRE PUMPHOUSE EQUIPMENTS1. MAIN PUMPSET:Supply and Installation of Electrical 3 phase 415v , 50Hz motor driven Horizontal End Suction Top Discharge Centrifugal pumpset with bronze impeller, cast iron body rated 137 Cu.m/hr at 70MWC 3000 RPMWithElectrical motor of Suitable 75HP, TEFC andcomplete with all accessories.For Hydrant System
498	2. STANDBY PUMPSET:Supply and Installation of Diesel engine driven horizontal end suction centrifugal pumpset with bronze impeller, cast iron body rated 137 Cu.m/hr at 70 MWC.The pump should have RPM between 2150 complete 90HP with all accessories
499	3. JOCKEY PUMPSET:Supply and Installation of Electrical 3 phase 415v , 50Hz motor driven horizontal Side suction Top Discharge centrifugal pumpset rated 10.8Cu.M/hr. at70MWC, 2900-3000RPM WithElectrical motor of Suitable 10HP, TEFC and complete with all accessories For Hydrantsystem.
500	4. FIRE PUMP PANEL:a). Autostart panel for theDiesel engine complete auto/ manual switch, indication lamps protective fuses with battery charger, suitable of working on 230 V, AC, single phase, enclosure being vermin & dust proofb). Supply and Installation of MCC with Star & Delta starter for the electrical motor driven pumpset / DOL starter Jockey pumpset complete with isolator switch, voltmeter, ammeter manual / auto mode switch, indicating lamps etc.,

Tender Documents

SR No	FileName	File Description
1	Click here to download tender document	Tender Documents
2	Click here to download tender document	Tender Documents
3	Click here to download tender document	Tender Documents
4	Click here to download tender document	Tender Documents

Also Visit

Tenders

Tamil Nadu Tenders

Construction Tenders

Building Construction Tenders

Building Work Tenders

Disclaimer

We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.

Top

Tender For Tender For Improvement Works To The Medical And Surgical Blocks Of Chennai Port Authority Hospital, Chennai-Tamil Nadu

Tender Documents

Disclaimer

About Us

Services

Browse Tenders

For Sales Inquiry

Tender For Tender For Improvement Works To The Medical And Surgical Blocks Of Chennai Port Authority Hospital, Chennai-Tamil Nadu

Tender Documents

Disclaimer

OTP Verification

About Us

Services

Browse Tenders

For Sales Inquiry

Connect With Us