|
| 1 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises.complete all as directed. |
| 2 | M & L for screed bed or bedding layer 15mm thick in cement mortar(1:6) for laying floor finishes Complete all as specified and directed. |
| 3 | M & L for non skid ceramic coloured /printedtiles 7 to 8 mm thick (square / Rectangular)area of each tiles exceeding 0.18 sqm but not exc 0.36 sqm in floorsetc set and jointed in neat cement slurry and pointed in coloured cement to match the tiles. |
| 4 | M & L for non skid ceramic coloured /printedtiles7 to 8mm thick (square / Rectangular)area of each tiles exceeding 0.11 sqm but not exc 0.18 sqm in floorsetc set and jointed in neat cement slurry and pointed in coloured cement to match the tiles. |
| 5 | All as per item no 3 for dado /skirting Complete all as specified and directed. |
| 6 | M & L for glazed ceramic coloured / printed tiles 300mm x 450mm, 6 to 7mm thick, on vertical surfaces set and jointed in neat cement slurry and pointed in white/coloured cement to match the tiles, complete all as specified and as directed. |
| 7 | Demolition of cement concrete (unreinforced)in ground floors and pavings not exceeding 15 cm thickness.(below or above ground level) Complete all as specified and directed. |
| 8 | M & L for 75 mm thick PCC (1:3:6) type C2 using 40mm graded stone aggregate as in plinth protection finishing the surface even and smooth without using extra cement Complete all as specified and directed. |
| 9 | Taking down cement or cement lime plaster of any description on brick or stone walls, etc. including racking out joints, hacking for key, scrubbing down with water etc.&removing rubbish to a disance not exc 250m Complete all as specified and directed. |
| 10 | M&L for rendering 15 mm thickreadymade plaster on inner/outer walls by adding 17-19% of potable water by weight of material for thickness above 15mm it is recommended to be applied in multiple layers. ready mix plaster shall complies with IS 1661-1972, IS 2250-1965, IS 2402-1963 and confirms the compressive strength @ 28 days 10-12 Mpa/Bulk density 1500-1600 Kg/m3. (Note : The rate quoted by contractor shall include cleaning of surface, application as per instruction and scaffolding upto 20 Mtr ht all as specified and directed) |
| 11 | M/L for preparing newly plastered wall surfaces andapplying two coat of distemper oil emulsion over 1mm thick wall care putty, complete all as specified . |
| 12 | M & L for applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50gm/litre and UV resistance as per IS 15489:2004, Alkali and fungal resistance, dirt resistance exterior paint ofrequired shade (Company Depot Tinted) with silicon additives @1.43 litre/10 sqm over and including priming coat of exterior primer applied @ 0.90litre/10 sqmover new surfaces. |
| 13 | Demolition brick work or stone/ boulder masonery built in cement mortar including all quoins , pillars etc |
| 14 | M & L for brick work using sub class \"B\" old size bricks, straight or curved on plan exceeding 6m mean radius built in CM (1:6) complete all as specified. |
| 15 | Taking down chowkats or frames with shutters (without taking off shutters from the frame)not exc 1.5 sqm each.& removing to or from store complete all as specifed & directed. |
| 16 | Taking down chowkats or frames with shutters (without taking off shutters from the frame) but exc. 1.5 sqm n. exc.4sqm each & removing to or from store complete all as specified and directed. |
| 17 | M&L for Pressed steel frames 125X60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc.,supplied and fixed complete all as specified and directed. |
| 18 | S&F 35mm thick factory made Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed |
| 19 | S & F 35 mm thick Second class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., rs, edges of framing plain, chamfered complete all as specified and directed. |
| 20 | S&Fthree trackaluminumpowder coated sliding window with three sliding shutter , the size of outer frame three track100 x 37x 1.50mm ( using two track for glazed window shutter and one track for wire gauged ) ,thesectionshutter size 37x 18x 1.2mm)and glazing with 5 mm thick Transparency glass of poly carbone including all-aroundsuitablerubber gasket andstainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.4mm and fixed on aluminum flatand inserted in the frame ofshutterwith tracking arrangement each sliding window shall be provided with one number handle includingGrill, locking arrangement & 2 numbers’s sliding rollers of nylon with including all necessary fittings |
| 21 | S & F 125 mm long Mild steel barrel tower bolts, stove enamelled black, with bright bolt and fixed |
| 22 | S & F floor door stopper of chromium plated body with rubber shoe fixed in door, overall length of cover plate140 mm all as specified and directed. |
| 23 | S & F butt hinges, medium weight, Miled steel and fixed, size of hinges 100mm complete all as specified and directed. |
| 24 | S & F 150 mm long Extruded brass handles,fabricated type polished complete all as specified and directed. |
| 25 | S & F 100 mm long Extruded brass handles,fabricated type polished complete all as specified and directed. |
| 26 | Supply and fix300 mm long ABrass, sliding door bolt with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixedcomplete all as specified and directed. |
| 27 | M & L for Oldpainted surface to steel and iron surfaces of any description, over 10 cm in width or girth, not otherwise described with one coats of synthetic enamelincluding preparation of surfaces complete all as specified and directed. |
| 28 | M & L for newly painting to steel and iron surfaces of any description, over 10 cm in width or girth, not otherwise described with two coats of synthetic enamel paint over a coat of red oxide primer including preparation of surfaces complete all as specified and directed. |
| 29 | Factory made single extruded WPC (wood polymer Composite) solid door/ window/ Ceosetory window & other Frames/ Chowkhat of size 45 x 70 mm comprising ofPVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wwod powder/ rick husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms ) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded stat headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N / mm 2 and resistance to spread of flame of Class A catogory with property of being termite/ borer proof, water / moisture proof and fire retardant and fixed in position with MS hold fast/lugs / SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). |
| 30 | Factory made single extruded WPC (wood polymer Composite) solid plain flush door shutter of 35 mm thickcomprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/ cum and screw withdrwal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N mm2 modulus of elasticity 850 N / mm2 and resistance to spread of flame of Class A catogary with property of being termite/ borer proof, water/ moisture proof and fire retardanat and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS screws, all as per direction of Engineer-In-Charge (Note:- stainless steel butt hinges and necessary SS screws shall be paid separately. |
| 31 | M & L for painting tonew wood and wood based surfaces of any description, over 10 cm in width or girth, not otherwise described with two coats of synthetic enamel paint over a coat of pink primer including preparation of surfaces. |
| 32 | M&L for preparation of old painted wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying one coat of Synthetic enamel paint (Ordinary tint) complete all as specified and directed. |
| 33 | Taking up or down 15 mm bore steel tubing and connections, including cleaning for refixing or removal to store. |
| 34 | Taking up or down 20mm bore steel tubing and connections, including cleaning for refixing or removal to store. |
| 35 | S&F GI water tubing of 15mm dia ,medium grade conforming to IS-1239(Part -1) including all fittings such as bends,tees,short pieces,connectors,elbows,reducers,union dockets etc & fixed to walls,ceilings, & laid on floors complete all as specified and directed. |
| 36 | S&F GI water tubing of 20 mm dia ,medium grade conforming to IS-1239(Part -1) including all fittings such as bends,tees,short pieces,connectors,elbows,reducers,union dockets etc & fixed to walls,ceilings, & laid on floors complete all as specified and directed. |
| 37 | S&F in repairsstop valves, cast copper alloy, fency type chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed for 15mm bore dia of pipe. |
| 38 | S&F in repairsstop valves, cast copper alloy, fency type chromium plated with long shank & cup (concealed) , screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed for 15mm bore dia of pipe. |
| 39 | S & F vitreous china wash basin(pedastel type), white, flat back, size 620X480X185 mm, (flat back or angle back type) including brackets and including cutting for and pinning in ends of brackets or erecting stand, fixed in repairs.Make i ( Jaquar cat Part No:- FNS-WHT-40801 ii ( Ceracat Part No :-1067 Aor Hindware Equalant. |
| 40 | S & F in repairs15 mm bore Fancy type pillar taps, Cast Copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe and fixed.Make i ( Jaquar cat Part No:- COP -001BPM ii ( Marccat Part No :-MFX- 2010 or Cera Equalant. |
| 41 | S&F 32mm dia waste fittings, brass, chromium plated for glazed ware sinks, basins, etc with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed. |
| 42 | S & F in repairs bib taps, cast copper alloy, 15 mm dia, Chromium Plated, fancy type with crutch or butterfly handle, screwed down for iron pipe and fixed etc complete all as specified.Make i ( Jaquar cat Part No:- KUP- 35037 PM ii ( Marccat Part No :-MFX - 2170 or Cera Equalant. |
| 43 | S&F for mirror with frame 500x700mm size cat part No. B3510936 cera or equivalent) complete all as apecified & directed |
| 44 | M & L for 32mm bore high density polyethylene pipes (HDPE) complete all as specified and directed. |
| 45 | M&L for 75mm dia Cast ironfloor trap with grating including jointing to waste pipe fixed in cement concrete (1:2:4) type B1 complete all as specified and directed. |
| 46 | S&F brass chromium plated tubular towel rail, 20 mm dia, D; type, 60 cm long between flanges complete all as specified and directed.Make i ( Jaquar cat Part No:- ACN 11815 ii (Marc or Cera Equalant. |
| 47 | S&Fchromium plated Soap disk fixed to plug with chormium plated brass screws all as specified and directed.Make i ( Jaquar cat Part No:- ACN-1131N ii (Marc or Cera Equalant. |
| 48 | S&F in repairs Chromium platedshower rose 125 mm swivel typeMake i ( Jaquar cat Part No:- OHS-35495 ii ( Marccat Part No :-MSR - 1170N or Cera Equalant. |
| 49 | S & F 20mm Dia Aluminium alloy anodised curtain rod decorative fency type with brackets complete all as specified. |
| 50 | S & F PVC connections 15mmdia , 450mm long, , withPTMT nuts& washers at both ends |
| 51 | DismatlingPVC Water tank Exc 250 & n exc 500 ltrand removing from site as specified and directed |
| 52 | S & F Rotational moulded PVC water storage tanks 500 Ltrs capcity three layer (cylindrical vertical with closed top) hoissted and fixed in position all as specified |
| 53 | S and F Ball brass valve 20 mm dia high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule complete all as specified and directed. |
| 54 | M&L for 25 mm thickCement concrete type-B-1 1:2:4 (20 MM graded aggregate ) all as specified and directed |
| 55 | Dismantling of wall and ceiling boards (fiber, pulp, insulation etc,) or insulation boards/slabs/blankets, any thickness including cover fillet complete all as specified and directed. |
| 56 | S & F for Aluminiumanodised snap grid frame work for false ceiling comprising of following section for making partitions of 605 X 605 mm size fixed to walls with rawl plugs and screws and hang to roof with s 6 mm dia. G.I. (upto1200mm length) adjusting levelfixed to roof slabs by means ofceilling cleats made out of G.I.flat 40 x 3 mm size 60mm longand expansion hold fasteners12.5mm dia. 40mm long complete all as specified. size of main tee shall be :-(i)36.5mmx25mmx1.4mm thick, Weighing 0.24Kg/Rm(ii)Cross Tee 23.5mmx36.4mmx1.4mm thick Weighing 0.191 Kg/Rm and (iii)Wall angle 40mmx25mmx2mm thick. Weighing 0.36 Kg/Rm |
| 57 | S & F 4 mm thick non asbestos fiber disigner ceiling (E-board classic) board / tiles for insulation and accoustic purpose, 600 X 600 mm size fixed with staples on snap grid as in ceilingwith and including dusting of surface and applying two coats of oil bond distemper over a coat of primer complete all as specified and directed |
| 58 | Dismantaling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed. |
| 59 | S&F Pre-painted galvaLume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strenth of 550 Mpa as in roof covering / clading to waall , fixed self tapping screws complete all as specified and directed. |
| 60 | S&F Pre-painted galvatume aluminium zinc coating GI based Plain steel sheet 0.50mm thick of an colour having tensile strenth of 550 Mpa as in roof covering / clading to waall , fixed self tapping screwscomplete all as specified and directed. |
| 61 | M & L for hard core of gauge not exc. 63mm, deposited, spread and leveled in layers not exc. 15 cm thick, watered and rammed to a true surface using broken stone or boulders complete all as specified and directed. |
| 62 | M&L 75 mmthick cement concrete 1:4:8 type D-2 finished fair and even as in sub base Complete all as specified and directed. |
| 63 | M & L for 15 mm thick screed bed or bedding layer in CM 1:6 to receive floor finishes complete all as specified and directed. |
| 64 | M&L for chequred cement concrete tiles of size 300x300x25 mm thick coloured rubber pressed glossy finish, set and jointed in neat cement slurry and pointed in white or colour cement and match the surace of tiles as foor/staps, complete as all specified and directed. |
| 65 | M & L for providing plain cement concrete type B-1, 1:2:4 (using 12.5 mm graded crushed stone aggregate) as in coping, bed block for embedding hold fasts, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles & throating as directed including necessary form work as required complete all as specified and directed. |
| 66 | Surface channel in concrete 1:3:6 (40 mm graded aggregate) for drain complete all as specified and directed. |
| 67 | Extra for forming fair finished drain orchannel 30 cm inner girth in cement complete all as specified and directed.concrete, using ex- tra cement, includingforms, moulds, mi- tred/stopped ends etc.All as specified and directed. |
| 68 | M&L for plain cement concrete 1:4:8 type D2 in foundation, filling and mass concrete all as specified and directed |
| 69 | M&L RCC(Nominal Mix), Type B1 1:2:4 (20mmgraded aggregate) Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed. |
| 70 | M&L RCC(Nominal Mix), Type B1 1:2:4 (20mmgraded aggregate) Columns, pillars, piers, posts and strutscomplete all as specified and as directed. |
| 71 | M&L RCC(Nominal Mix), Type B1 1:2:4 (20mmgraded aggregate) as in beams, cantilever, lintels etc complete all as specified and as directed. |
| 72 | M&L form work to sides of concrete foundations, footings, bases of columns, raft and raft beams, plinth beams or similar works vertical or to batter for rough finished surface of concrete |
| 73 | M&L form work to sides and soffits of roof beams, lintels lever shelves incl supports over hang etc rough finished surfaces of concrete flat all as specified. |
| 74 | M&L form work to sides of pillars, posts, struts, columns for rough finished surface of concrete |
| 75 | M&L mild steel TMT bars 10mm dia and over, cut to length, bent to shape required incl cranking, bending spirally for hoping for columns hooking ends and bindind with ms wire (annealed) not less than 0.9mm dia quality confirming to all as specified. |
| 76 | Description same as above but, 5 mm dia and over and incl 10mm dia in stirrups, spacers and binders |
| 77 | M&L for 100mm thick cement concrete 1:2:4 type B-2 (using 40mm graded stone aggregate) as insub-base & pavingsetc complete all as specified and directed |
| 78 | M&L for Sand filling under floors or in foundations including watering and consolidation |
| 79 | S&F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 all as specified |
| 80 | S & F for Mild steel screw bolts(machine made) 16mm diameter of neckwith hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 5cm long |
| 81 | S & f for Plates Fe-410- W(Gde E-250) quality B (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment |
| 82 | M&L for 25 mm thickCement concrete type-B-0 1:2:4 (12.5 mm graded aggregate) as subbase in floors all as specified and directed |
| 83 | M/L for preparing newly plastered wall surfaces andapplying two coat of distemper oil emulsion over a coat of primer(Priming the plastered and other surfacepreparatory to distempering) incl 3 mm thick applying a layer of JK/ Birla puttyon wall surfaces including cornics etc for proper levelling of plaster complete all as specified and directed. |
| 84 | Material & Labour for prepration of surfaces for New plastered or unplastered surfaces and applying Two or more coats of 100% remium acrylic emulsion paint havingVOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance,dirt resistance exterior paint of required shade(Company Depot Tinted) with silicon additives@ 1.43 litre/ 10 sqm over and including primingcoat of exterior primer applied @ 0.90 litre/ 10sqm over new surfaces |
| 85 | S&F 18mm thick MDF Board both side finished as in wardrobe/ cup board shutterallas specified and as directed by Engineer-in-Charge. |
| 86 | S&F 25mm thick MDF Board both side finished as in cupboard shelves/ kitchen cabinet and as directed by Engineer-in-Charge. |
| 87 | S&F Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheetinclusive of solvent cement and fixing at site on PVC frame as perpecificationsand drawing complete. |
| 88 | S&F aluminium powder coated door with shutter and frame of aluminium section sliding typeas per following specifications with and including round type aluminium handle, tower bolts, hinges, panes etc and as directed at site. Make Jindal or its equivalent approved make:- (a)DOOR FRAME :100 x 44 x1.6 mm section for complete frame. (b)DOOR SHUTTER : Top & bottom rail of 100x44x1.6 mm, middle rail of 83 x 44 x 1.6mm, both styles of 83 x 44 x 1.6 mm size shall be used. (c)GLASS PANE : 5mm thick sun broken glass fixed with gasket with aluminium clip , jointing clips, glazing clips, rubber packing, screws etc. (d) Jointing cleats, glazingclips, rubber packing,anodized aluminium snap beading, screws, anodized aluminium fittings such as 100mm long 03 Nos. hinges, aluminium handles , aluminium tower bolts ,and mortice lock 6 Levers etc complete all as specified and directed |
| 89 | Taking down carefullyAluminium/copper wiring of any size (for light, fan, socket or power etc complete) ( fittings such as switches, sockets, ceiling roses, pendent holders regulators, tube lights etc to be measured and paid separately) and making good disturbed surfaces of wall, roof etc to match with existing surface complete all as specified and directed. |
| 90 | S & F point wiring for one light point / fan point / bell point / 5 Ampere socket outlet point (independent point), controlled by one, one way switch with 1.50 sqmm size PVC insulated unsheathed 1100 volts grade single core (multi-stranded) copper conductor cable (FRLS) drawn into and including medium grade PVC conduit concealed (not less than 20 mm dia) all necessary fittings and accessories fixed concealed (including chase cutting in brick/stone masonery wall for fixing conduit and plastering the external surfaces and matching the same with existing suface)and sunk cast ironor pressed steel terminal boxes for mounting fittinglike switches, sockets, lamp holders, sketch fittings and covered with 3 mm thick plastic laminated bakelite sheet cover fixed with brass screws and cup washers including one continuous run of PVC insulated (green colour) 1.50 sqmm sizecopper conductor cable as in earth wire and connected to common earth dolly complete all as specified and directed, are as follows :-(a)One light/one fan/one bell point controlled by one, one way switch. |
| 91 | (b)One socket outlet 5 pin 5 Amp controlled by one, one way switch on same board. |
| 92 | (c)One socket outlet 5 pin 5 Amp controlled by one, one way switch on independent board. |
| 93 | All as per item No.2 hereinbefore but wiring with using cable 2.50 sqmm size copper wire (FRLS) and earth wire of PVC insulated (Green colour) 2.50 Sqmm sizecopperwire for one 6 pin socket outlet, 16 Amperes on independent board. |
| 94 | S&F switch piano flush type single pole, one way 5 Amp complete all as specified and directed. |
| 95 | S&F socket out letmulti 5 pin, 5 Amps, flush type complete all as specified and directed. |
| 96 | S&F switch piano flush type single pole, one way 15 Amp complete all asspecified and directed. |
| 97 | S&F socket out let 2 in1,3 pin, 5 and 15 Amp, flush type complete all as specified and directed. |
| 98 | S&F ceiling rose, PVC/ Poly carbonate,isolated body three terminal complete all as specified and directed. |
| 99 | S & F lamp holder angle type PVC/Poly carbonate type insulated body with back plate suitable for batten/wall fitting complete all as specified and directed. |
| 100 | Supply and fixing LED lights fitting 1x 20W, 220V,AC decorative box type with driver, holder includingLED tube light connecting up with two core flexible copper conductor cable of suitable size from ceiling rose complete all as specified & directed. |
| 101 | Taking down unservicable MCB and S&FMCB SP,240 volts,AC C curve, 10 KA 6 to 32 Amps . |
| 102 | Taking down unservicable MCB and S&FMCB SPN , 240 volts,AC B curve, 10 KA 40 Amps. |
| 103 | Taking down unserviceable MCB, S&FMCB TPN , 415 volts, AC C curve, 10 KA 100Amps. |
| 104 | Supply and fixing LED bldg security light fitting 35 /36 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 66 protection complete. all as specified and directed . |
| 105 | Taking down unservicable DB and S&F sheet metal enclusure for DBs(double door type)single pole and neutral 12 way including blanking platge as required with 200 Amps rated bus bar, 240 volts fixed complete all as specified and directed . |
| 106 | Taking down unservicable DB and S&F sheet metal enclusure for DBs(double door type)single pole and neutral 8 way including blanking platge as required with 200 Amps rated bus bar, 240 volts fixed complete all as specified and directed . |
| 107 | S & FLED bulk head fitting, 1 x 10 watt with PDC aluminium housing and milky diffuser including LED light driver holder, complete with all accessories and including connecting up with three core twisted flexible copper conductor cable with suitable size of 230 Volts, 50 Hz complete all as specified and directed. Make : Havells/Bajaj/Crompton |
| 108 | M&L for earthing complete with galvanised steel,earth plate electrode 600x600mm x 6mm thick burried directly in ground verticaly (earth pit not less than 2.25 mtrs belowground level ) with top edge of the plate not less than 1.5 mtrs below normal ground level connected to galvanised earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron/steel all as shown in electrical plate No 3 on page 497 of MES schedule 2009 part - I connected to main switch board/main DBs/earthing test point including all necessary excavation and earth work in hard/dense soil common salt and charcoal dust mixed and packed 150mm thick all round the GI earth plate, watering pipe 20mm dia GI medium grade. GI sheet 0.63 mm thick funnel, wire gauge, 50mm thick RCC cover in PCC 1:2:4 type B1 duly reinforced with MS round bars 6mm dia @ 150c/c both ways and pit/chamber in PCC 1:3:6 type C1 with suitable lifting handleto cover, GI protection pipe 15mm dia light grade up to 7.5mtr from electrode GI pipe to be fixed with complete all as specified and directed. |
| 109 | S& F LED Bulb of 9 watt as specified |
| 110 | Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with two core flexible copper conductor cable of suitable size complete all as specified and directed |
| 111 | S&F sheet metal enclosure single pole and neutral with a two pin and earth plug and socket complete with one single pole MCB 240 Volts 20 Amps complete all as specified and directed. |
| 112 | Taking out old U/S Sub main wiring for replacement includingS&F sub main wiring withtwo single core FRLSPVC insulated and sheathed 1100 Volts grade,6 Sqmm size cables, PVC insulated stranded copper conductor fixed in PVC conduite pipe 25mmdia with all accessories and one continuous run of6.0 Sqmm copper conductor PVC complete all as specified and directed (Note :-Two single core cables along with earth wire and conduit shall be measured as one unit length). |
| 113 | S&F Exhaustfan metallic bady ISI mark, 450 mm size with louvers including cutting openings, through brick/ stone wall , making of holes and grouting of suitable size of nuts and bolts for 450 mm exhaust fan and making good dismantled portion and making connection with wire of suitable size and connecting accesssories complete all as specified and directed. |
| 114 | S&F Exhaustfan metallic bady ISI mark, 380 mm size with louvers including cutting openings, through brick/ stone wall , making of holes and grouting of suitable size of nuts and bolts for 380 mm exhaust fan and making good dismantled portion and making connection with wire of suitable size and connecting accesssories complete all as specified and directed. |
| 115 | Supply and fix electric water heater, storage type steel body with digital display and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc. complete all as specified and directed. |
| 116 | Supply, laying, jointing and commissioning LT XLPE 1100 volts 16 sqmm 4 coregrade heavy duty under ground cable PVC insulated,strandred aluminium conductor served with inner sheathing of PVC tape, armoured with GI steel or tape and over all PVC sheathing laid in trenches, floor through pipes, in duct on pole and roads etc.complete all as specified and directed. |
| 117 | Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m deep for laying ofunderground cable and getting out in any type of soil complete all as directed by the Engineer-in-Charge |
| 118 | Returning, filling in, including spreading,leveling watering and well ramming in layers n.exc 25 cms. thick in soft / loose soil complete all as specified and directed by Engr -in -charge . |
| 119 | Removal of surplus soil not exceeding 50 Mtr and depositing where directs at a level not exceeding 1.5 Mtr above the starting point complete all as specified and directed by Engr-in-Charge. |
| 120 | S & F Recess mounting LED luminaire 600mm x 600 mm ,36 W, 220V, with high efficiency PMMA diffuser soft glare free light suitable for recessed mounting ,with powder coated CRCA housing with LEDs, seamless front frame complete with driver and all accessories internally pre-wired and including necessary cutting as required in panel and connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed. |
| 121 | M&L for sand cushioning in trenches spreading and consolidation 8cm thick before laying the cable & 15 cm of sand after laying the cable complete all as specified |
| 122 | M&L for laying of bricks well burnt sub class ‘B’ (old pattern) laid flat for cable protection width equal to the lengrth of brick complete all as specified . |
| 123 | M & L galvanised steel water tubing \"light grade\"25 mm bore with all fittings laid under the roads, drains, culverts and fixed on poles etc complete all as specified and directed . |
| 124 | Supply and fixing LED batten light fitting20W, 220V,with microwave motion sensor based technology with aluminium housing & integrated electronic driver of make Havells with Cat part no LUMILINESMART20WLED865PCWH or equivalent make of Bajaj/Philips/Crompton complete all as specified & directed. |
| 125 | Supply and fix High quality LED T8 indoor batten tube light 20 Watt with aluminium extrusion in D shaped have large diameter for increased convection heat transferincl one LED PC tube rod and driver,internaly pre wired of 1.5 sqmm twin twisted flexible cableall as specified & directed.NOTE: The contractor must submit 5 years warranty for LED fitiings. |
| 126 | S&F sheet metal enclusure for DBs(double door type)single pole and neutral 4 way including blanking platge as required with 200 Amps rated bus bar, 240 volts fixed complete all as specified and directed . |
| 127 | S&F service connection cable, 1100 volts grade heavy duty PVC insulated aluminium conductor, 10 Sqmm 2 core size, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4mmsuspensionwire, one twin core cable flat or circular, complete all as specified and directed. |
| 128 | M & L galvanised steel water tubing \"light grade\"20 mm bore with all fittings laid under the roads, drains, culverts and fixed on poles etc complete all as specified and directed . |
