Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Water proofing treatment to sunken slab and adjjoining vertical surfaces as specified under :-(a) M&L rendering 10 mm thick in cement plaster (1:3) using coarse sand mixed with integral water proofing compound trowel even and smooth with steel trowel on sunken surfaces (Note : WPC shall be measured and paid separately)(b) Applying first coat of chemical pidifin 2K(Dr Fixit) on cleared RCC surfaces @ 0.86 Kg/Sqm (Minimum) as recommended by manufacturer.(c) Provide a layer glass fibre mesh of size 2.25mm x2.25mm (45 GSM) over first coat of chemical Pidifin 2K as per manufacturers recommendation.(d) Applying second coat of chemical Pidifin 2K (Dr Fixit) @ 0.86 Kg/Sqm (minimum) layer glass fibre mesh of size 2.25mm x 2.25mm (45 GSM) as recommended by manufacturers. |
| 2 | M&L for PCC 1:5:10, type E-2 as in filling of sunken floors etc.complete all as specified and directed by engr in charge |
| 3 | Taking down cement plaste of any description and in any position of brick or stone wall/concrete surfaces on walls ,ceiling etc including raking out joints ,hacking for key scrubbing down with water etc & prepared to receive new plaster complete all as specified and directed Note: if existing plaster found on site in multi layers, in this situation contractor will remove complete plaster,rate for the same will be included deemed in quoated rates |
| 4 | M&L for 15mm thick rendering on fair faces of brick/concrete surfaces in CM 1:4 finished even and smooth without using extra cement mixed with water proofing compound (Note :-WPC shall be measured & paid separately) |
| 5 | M&L for rendering 5 mm thick in Cement Mortar (1:3) on ceiling finished even and smooth without using extra cement complete all as specified and directed. |
| 6 | M&L for 15 mm thick rendering on surfaces other than fair faces of brick/concrete surfacesin CM (1:6) and finished even and smooth without using extra cement complete all as specified and directed. |
| 7 | Supply only Integral waterproofing compound.complete all as specified and directed. By Engr-in-charge |
| 8 | M&L for applying acrylic wall care putty on old/ new plastered internal/Externalsurfaces of walls/ceilings/soffits (thickness vary from 1.5 to 2.5 mm as required for desired smoothness and levelling of surfaces in two or more layers) by using ready made wall care putty including sand papering after filling the putty to make surface smooth and ready for receiving painting etc complete all as specified and directed.Make of wall Putty : JK wall Putty / Birla Wall care Putty / Bison Wall Putty.Notes : (i) The prepared surface after wall putty, the contractor will inform to the GE as well as to the Engineer-in-Charge for site inspection before applying further finishes. Please note that the further finishes work will start only after approval of the prepared surface from the GE /Engineer-in-Charge. |
| 9 | Complete removal of existing treatment of any type/description from walls/RCC surfaces/ceiling/chajjas/roof projections etc with mechanical means/grinder complete all as specified. |
| 10 | Preparation of surfaces and applying 02 coats of exterior emulsion paint (light shade) on old/ new plasteredwith highlighter of any approved shade,@ 5 sq.m/litre/2 coats by using roller to external walls/RCC surfaces/soffits of chajjas/roof projections/cantilevers/balcony etc surfaces over & including a coat of exterior wall primer @ 11 sq.m/litre/1 coat as recommended for under coat by manufacturer of exterior emulsion by using following brands of emulsion and primer complete all as specified and directed.Make of Exterior Wall Primer : Asian / Berger / Nerolac [Best Quality].Make of Exterior Emulsion : Asian (APEX)/ Berger (WEATHER COAT ANTI DUST) / Nerolac (EXCEL TOTAL) . |
| 11 | Preparation of surfaces and applying 02 coats of interior emulsion paint (light shade) on old/ new plastered@ 10 sq.m/litre/2 coats by using roller/brush to wall surfaces over & including a coat of interior wall primer @ 10 sq.m/litre/1 coat as recommended for under coat by manufacturer of interior emulsion by using following brands of emulsion and primer on existing yellow coloured surface complete all as specified and directed.Make of Interior Wall Primer : Asian / Berger / Nerolac [Best Quality].Make of Interior Emulsion : Asian (tractor shyne)/ Berger (bison) / Nerolac (BEAUTY sheen) |
| 12 | M&L for preparing new plastered surfaces of ceilings and applying three coats of white wash by making the lime slaked at site and shall be mixed and stirred with about five liters of water for 1 kg of unslaked lime to make a thin cream. This shall be allowed to stand for a period of 24 hours and shall then be screened through clean coarse cloth. 1 kg of gum dissolved in hot water shall be added to every one cubic meter of lime cream. About 1.3 Kg of sodium chloride dissolved in hot water shall also be added for every 10 kg of lime for making the coating hard and rub-resistant. Small quantity of ultramarine blue (upto 3 gm per kg of lime) shall also be added to the last two coats of white wash solution and the whole solution shall be stirred thoroughly before use complete all as specified. |
| 13 | M&L for preparing existing treated surfaces of ceilings including cornices and applying two coats of white wash by making the lime slaked at site and shall be mixed and stirred with about five liters of water for 1 kg of unslaked lime to make a thin cream. This shall be allowed to stand for a period of 24 hours and shall then be screened through clean coarse cloth. 1 kg of gum dissolved in hot water shall be added to every one cubic meter of lime cream. About 1.3 Kg of sodium chloride dissolved in hot water shall also be added for every 10 kg of lime for making the coating hard and rub-resistant. Small quantity of ultramarine blue (upto 3 gm per kg of lime) shall also be added to the of white wash solution and the whole solution shall be stirred thoroughly before use complete all as specified and as directed by Engineer-in-Charge. |
| 14 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises |
| 15 | M&L forvitrified ceramic tiles double charged 10mm thick (square/rectangular), polished, coloured (light shade as approved), area of each tile not exceeding 0.36 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:4 complete all as specified and directed. Make: Johnson (Marbonite)/Kajaria/Somany/ Orient Bell Granito/ Asian Granito/ Oracle Grenito (Marbito) |
| 16 | M&L for vitrified ceramic tiles double charged10mm thick (square/rectangular), polished, coloured (light shade as approved), area of each tile not exceeding 0.36 sqm,as in as in vertical surface like dado/ skirting etc , set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:4 complete all as specified and directed.Make: Johnson (Marbonite)/Kajaria/Somany/ Orient Bell Granito/ Asian Granito/ Oracle Grenito (Marbito) |
| 17 | M&L for non skid ceramic ede cut tiles (coloured) 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:4, complete all as specified and as directed. Make : Somany/Johnson/Kajariya/Sunheart. |
| 18 | M&L for glazed ceramic tiles (coloured) 600x300x 7mm thick on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10 mm thick rendering (as screed bed) in cement & sand mortar 1:4, complete all as specified and as directed. Make : Somany/Johnson/Kajariya/Sunheart. |
| 19 | M&L Granite slab (telephonic Z Black)work 18-20mm thick in floors steps, cooking platforms and likeincluding pointing in white cement with admixture of pigment to match with granite shade over & including screed bed 15mm thick in CM 1:6 including cutting recess opening for the sink portion and embedding complete all as specified and directed by Engineer-in-Charge. (Note : No deduction shall be made for opening of sink portion, shall deemed to be included in the quoted rate) complete all as specified and directed. By Engr-in-charge |
| 20 | Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and othersimilar situations complete all as specified and directed. By Engr-in-charge |
| 21 | M&L for preparation of old steel painted surfaces exc 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified. |
| 22 | Taking down chowkats or frame with shutters (without taking off shutters from the frame) n exc 1.5 sqm each complete all as specified and directed. By Engr-in-charge |
| 23 | Taking down chowkats or frame with shutters (without taking off shutters from the frame) exc 1.5 sqm and n exc 4.0 Sqm each complete all as specified and directed. By Engr-in-charge |
| 24 | Taking down shutters of any description and in any positionexceeding 1 sqm & not exceeding 2 sqm each complete all as specified and directed. |
| 25 | Taking down shutter of any description exc 1 Sqm and not exc 2 Sqm each and refixing in same opening including easing and adjusting of shutter as required including renewal of unserviceable screws all as directed. |
| 26 | Supply and fixing Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 850 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. Note: (i) For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made(ii) Cost for M.S. hold fast/ lugs or SS dash fasteners shall deemed to be included in the quoted unit rate nothing extra shall be paid on this account. |
| 27 | Supply and Fixing Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 850 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge.Note: (i) WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.(ii) Cost for M.S. hold fast/ lugs or SS dash fasteners shall deemed to be included in the quoted unit rate nothing extra shall be paid on this account. |
| 28 | Supply and Fixing Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65 x 150 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natu |
| 29 | Supply and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ ri |
| 30 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 35 mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder |
| 31 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type Skelton door shutter of size 35 mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibres (wood powd |
| 32 | Supply and fixing single liver basin mixer with popup waste system & 450mm long braided hoses, fency type, cast copper alloy, with capstan heads, chromium plated, screwed down, high pressure, with long screwed shanks and fly nuts, screwed for 15mm bore of |
| 33 | M&L forPlain fillets or beading of sectional area Exc3 & n. exc 6sq.cm of 2nd class hard wood square, rectangular or triangular in section , clean sawn, se-cured with nails or brads for securing wiremesh or similar worksput together with glue pinned at joints incomplete all as specified and directed by Engineer - in -Charge. |
| 34 | S & FPowder coatedAluminium alloy sections sliding windows with frames Series-C 20mm of frame size 92 x 31.75 x 1.90 mm and , 3 track sliding shutters duly fitted with neoprene beading, glazing clips,shutters with tinted glass 4mm thick and stainless steel wire cloth 0.36mm dia and average width of aperture 1.4mm , aluminium alloy handles etc. complete all as specified and directed. |
| 35 | S& FStainlesssteel-304wire cloth 0.36 mm nominal dia of wire and avarage width of aparture 1.40mm and fixed including necessary beading etc. complete all as specified and directed. |
| 36 | S&F in repair for butt hinges 100mm size medium weight stainless steel .complete all as specified and directed. By Engr-in-charge |
| 37 | M&L in repair for 150mm long extructed aluminium handle (back flat staple) fabricated type complete all as specified and directed. |
| 38 | S&F in repairAluminium anodised barrel tower bolt of extruded section 200 mm sizecomplete all as specified and directed. |
| 39 | S&Fin repair 300 mm long mild steel sliding door bolts, plate type, stove enameled black, with bright bolt not less than 12mm dia and including a minimum of 06 bolts and nuts, four on bolt plate and two on staple plate and fixed, complete, all as specified. |
| 40 | Preparation of old painted surface of wood and wood based materialany description and in any position over 10 cm width or girth and M&L for applying two coat of synthetic enamel paint complete all as specified and directed. by Engr-in-Charge. |
| 41 | S&Faluminium powder coatedventilator with fixed aluminium frame of size 65 x 40 x 1.98mm thick fixed in vertical position with aluminium vertical members andhalf portion to be provided with 4mm thick pin head glass and remaining portion to be louvered using 4mm thick pin head glass and louvered portion covered with stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm incl necessary channel frame work, including rubber gasket and aluminium beading complete all as specified. |
| 42 | M &L for Framed/unframed work such as angle, grills,gratings, etc.. with ends of bars shouldered and/or riveted,or forged into spikes; framed guard bars; barred iron doors;ladders; framedbalusters; walk ways; railings;girder ,channelframework of water tanksand similar work conforming to Fe.290.Gde-E-165etc complete all as specified. |
| 43 | S&F in repairs stainless steel curtain rod 25 mm dia (minimum weight 0.36 Kg per RM) with brackets, fancy knobs and rings (20 cm c/c) etc complete all as specified and directed by Engr-in-charge. |
| 44 | S&F in repair 10 litre capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets with flush pipe 32mm dia (Note: MAKE - CERA/PARRYWARE) |
| 45 | S & F in repair corner vitreous china wash basin, white flat back , size 450mmx300mm with and including Waste fittings, brass, chromium plated forbasins with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed with and including Supplying and fixing cast copper alloy chromium plated,fancy type,pillar tap,15mm bore,screwed down high pressure with or without lettered hot or cold with long shanks, screwed for iron pipe complete all as specified and directed. (Note: MAKE - CERA/PARRYWARE/JAQUAR) |
| 46 | S&F gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed of 20 mm bore,all as specified and as approved by GE/Engineer-in-Charge. |
| 47 | S & F in repairs wall mixer 3-in-1 system with provision for both hand shower and overhead shower complete with 115 mm long bend pipe with connecting legs and wall flanges complete all as specified and directed. by Engr-in-Charge.(Note: MAKE -CONFIRMING TO JAQUAR CAT PART-No. STE -107281 OR EQUIVALENT) |
| 48 | S & F in repairs sink mixer with swinging,spout wall mounted model with connecting legs and wall flangescomplete all as specified and directed. by Engr-in-Charge.(Note: MAKE -CONFIRMING TO JAQUAR CAT PART-No. STE -107309 OR EQUIVALENT) |
| 49 | Supply and fixing single liver basin mixer with popup waste system & 450mm long braided hoses, fency type, cast copper alloy, with capstan heads, chromium plated, screwed down, high pressure, with long screwed shanks and fly nuts, screwed for 15mm bore of |
| 50 | S&Fin repairs vitreous china water closet (squatting pan), orissa patern size 575 x 440 x 250 mm white with integral, foot rests an including \"P\" trap and lime bedding making good to floors complete (Note: MAKE -CONFIRMING TO JAQUAR CAT PART-No. ECH-WHT-451LE OR EQUIVALENT) |
| 51 | S & F in repairs 15mm dia angle valves, Chromium plated crutch or butterfly handle screwed down high pressure, screwed both ends for iron pipes or for unions.(Note: MAKE -CONFIRMING TO JAQUAR CAT PART-No. STE -107053 OR EQUIVALENT) |
| 52 | S & F in repairs 15mm dia long bodybib tap with angle valves, Chromium plated crutch or butterfly handle screwed down high pressure, screwed both ends for iron pipes or for unions.(Note: MAKE -CONFIRMING TO JAQUAR CAT PART-No. STE -107067 OR EQUIVALENT) |
| 53 | S&F in repairs shower rose 100 mm x100mm square size of brass chromium plated fancy type with or without swivel joint suitable for fixing to 15mm bore GI pipe complete all as specified and directed..(Note: MAKE -CONFIRMING TO JAQUAR CAT PART-No. EOS-542N OR EQUIVALENT) |
| 54 | S&F in repair health faucet spray type jet with brass jet, chromium plated, and 1.0 m long PVC flexible pipe complete all as specified and directed .(Note: MAKE -CONFIRMING TO JAQUAR CAT PART-No. STE -107067 OR EQUIVALENT) |
| 55 | S & F in repairs 15mm size PVC connections with PTMT nuts of length 450 mm.complete all as specified and directed. By Engr-in-charge |
| 56 | M&L in repairs 40mm dia Low density poly ethylene pipes(LDPE) of pressure rating 6 Kgf/cm2fixed complete to wall, ceiling or in floors etc complete all as specified and directed. By Engr-in-charge |
| 57 | S&F in repair 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed. By Engr-in-charge |
| 58 | S&F glass corner self assembly, fancy type,made of 5 mm thick sheet toughened glass of size 250x250mm,fixed with CP brackets,complete,all as specified and directed. |
| 59 | S&F in repairs CP brass tubular towel rail,20mm dia, ‘D’ type, 60cm long between flanges, fixed to PVC rawl plugs with chromium plated brass screws, complete all as specified. |
| 60 | M&L cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth all as directed. |
| 61 | S&F for Rotational moulded polyethylene water storage tank(white) in double layer of 1000 liter capacity (cylindrical vertical with closed top incl float valve) hoisted and fixed in position all as specified and directed by Engr-in-chagre |
| 62 | M&L for cutting grooves in brick wall, 75 mm wide and 65 mmdeep and shaping horizontal face of groove with cement mortar 1:3 /epoxy groutingto ends of landings, steps, cills sunshades, shelves lintels etc complete all as specified and directed. By Engr-in-charge Note:Epoxy grouting applied by approved applicator |
| 63 | M&L for cutting holes or through PCC block / RCC wall built in CM and making good in CM 1:3 or cement concrete 1:2:4 type B-1 as required, superficial area exc 150 sqcm but n.exc 400 sqcm complete all as specified and directed. By Engr-in-charge |
| 64 | Demolition and breaking up drain pipes (salt glazed ware, AC or Reinforced concrete) internal dia of pipe in 75mm set in cement mortar complete all as specified and directed. By Engr-in-charge |
| 65 | Demolition and breaking up drain pipes (salt glazed ware, AC or Reinforced concrete) internal dia of pipe in 110mm set in cement mortar and taking out of trenches, if required |
| 66 | S&F for 75mm PVC (SWR) pipes single socketed,inanylength with rubber ring joints, laid in trenches or in floors complete all as specified and directed. By Engr-in-charge |
| 67 | S&F for 110mm PVC (SWR) pipes single socketed,inanylength with rubber ring joints, laid in trenches or in floors complete all as specified and directed. By Engr-in-charge |
| 68 | S&F 75 mm bore PVC (SWR) pipes Type B ISI marked single socketed in any length with rubber ring joints laid on wall fixedcomplete all as specified and directed |
| 69 | S&F 110 mm bore PVC (SWR) pipes Type B ISI marked single socketed in any length with rubber ring joints laid on wall fixedcomplete all as specified and directed |
| 70 | S&F 75mm dia PVC (SWR) branch piece single (single \"Y\") equal or unequal with acess door.complete all as specified and directed. By Engr-in-charge |
| 71 | S&F 110mm dia PVC (SWR) branch piece Tee (Single \"T\") equal or unequal with acess door. |
| 72 | S&F 75mm dia PVC (SWR)bendsany radius with access door.complete all as specified and directed. By Engr-in-charge |
| 73 | S&F 110mm dia PVC (SWR)bendsany radius with access door.complete all as specified and directed. By Engr-in-charge |
| 74 | S&F for PVC (SWR) floor trap long body type, plain with grating including jointing with solvent cement |
| 75 | S&F for PVC (SWR) vent cowl 110 mm bore complete all as specified and directed. By Engr-in-charge |
| 76 | M&L PCC 1:2:4 type B1 using 12.5 mm graded aggregate as in hold fast, cill etc with necessarry form work complete all as specified and directed. By Engr-in-charge |
| 77 | Taking up or down existing unserviceable upvc/ mild steel water tubing and connections 15mm dia, any grade,of any description or in any position including fittings complete all as specified and directed |
| 78 | Taking up or down existing unserviceable upvc/ mild steel water tubing and connections 25mm dia, any grade,of any description or in any position including fittings complete all as specified and directed |
| 79 | Supplying and laying16 mm outer dia CPVC SDR 13.5 and plain CPVC SDR 11 fittings pipes fixed complete to walls, ceilings or in floors etc., any type of pipe etc in required length complete all as specified and directed |
| 80 | Supplying and laying25 mm outer dia CPVC SDR 13.5 and plain CPVC SDR 11 fittings pipes fixed complete to walls, ceilings or in floors etc., any type of pipe etc in required length complete all as specified and directed |
| 81 | Demolition of existing PCC as in form of roof padding incl backing over roof, any thickness including plastering and leaping (where full thickness removed or only a part there of disposal off rubbish upto a distance n.exc 100m, where directed. |
| 82 | M&L for cement concerete type C2 1:3:6 (20 mm graded aggrigate) as in filling and mass concerete etc complete all as specified and dirceted by Engineer-In-Charge. |
| 83 | M&L for 10mm thick rendering on fair faces of brick/concrete surfaces in CM 1:4 finished even and smooth without using extra cement mixed with water proofing compound.(Note :-WPC shall be measured & paid separately) |
| 84 | Material and labour for roof surface treated with PU Elastoseal primer with Epoxy Primer to seal the pores and enhance the adhesion of the coating, supplying and applying single component waterproofing liquid membrane based on pure, elastomeric, polyurethane resin cold applied of spray/brush applied membrane with an elongation of 650%+ 50 and tensile strength not less than 2 Mpa, crack bridging ability not less than 2mm. No leakage upto 5 bars of water pressure. Shore Hardness > 50 Shore. The minimum thickness to be applied shall be 1.5 mm, (overall) in two layers (each layer 750 micron) or as per manufacturer’s instructions so as to achieve thickness not less than 1.5mm including providing & laying of protective Geotextile fabric 150 GSM over the entire membrane with proper overlaps of 75mm before laying SRI roof tiles complete all as specified and as directed by Engineer-in-Charge..Note : (i) The treatment shall be carried out by authorised applicator approved by GE as per the manufacturerMake for PU Primer/ Membrane SIKA/ BASF, BERGER/ STP FOSROC/ SAINT GOBAIN, PIDILITE. |
| 85 | Making benching / Roof Kerbing with PCC (1:2:4) type B0 using WPC as per manufacturer\"s instruction along side wall adjoining to roof in concave shape complete all as specified and directed. Note : WPC shall be measured and paid separately. |
| 86 | Material & labourfor machine cut kota stone slab size as in flooring, stair case landing. treads of steps, 18-20mm thick single piece prepolishedover cement screed bed laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing completeincluding 20mm thick screed bed or bedding in cement mortar 1:6 all as specified and directed |
| 87 | Material & labourfor machine cut kota stone slab sizeas in skirting, dado, vertical surfaces etc, 18-20 mm thick single piece prepolishedover cement screed bed laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing includingbacking coat 15mm thickcement mortar 1:3 complete all as specified. |
| 88 | S&F sinks without drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes ; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting unions to pipe, overall size 495mmX420mm bowl size 410mmX330mmX160mm. |
| 89 | S&F in repair of PVC cabinet size 650 x 400mm, comprising of looking glass, space for bath soap, shampoo, tooth brush and paste, handle towel rail complete allas specified and as approved of any fo floowing makes :- HINDWARE / CERA / NEYCER / PARRYWARE/CLASSICcomplete all as specified and directed. |
| 90 | Demolition of cement concrete (unreinforced) in ground floor and paving n.exc 15 cm thickness below and above ground level,all as directed. |
| 91 | M&L 75 mm thick PCC 1:3:6 type D-2 (using 40mm graded stone aggregate) as in as in sub baseall as specified and directed. |
| 92 | M&L sand filling 25 mm thick under floor/over floor or in foundations including well ramming complete all as specified and directed by Engr-in-charge |
| 93 | M&L 60 mm thick coloured interlocking PCC tiles in approved design/colour setlaid over compacted sub soil / sand all as specified and directed. |
| 94 | Providing prrecast cement concrete Type B1 1:2:4 (20 mm graded aggregate) in appex stone/kerb stone with plain fair faces including chamfers, weathering throting etc and set in cement mortar 1:4 complete with joints to math size and shape as approved by engr-in-charge |
| 95 | Demolition of RCC slab , RCC tank, chajjas, kitchen slab, chimney and similar items complete all as specified and directed by Engineer - in -Charge. |
| 96 | Fixing of nozzles: Drilling Holes of 12mm dia up to 100 mm deep holes in structural members at the interval of 350 mm in staggered manner or along the crack line in Reinforced Concrete (RC) structural element including cleaning of the holes by air blower and inserting 12mm dia NRV (Non Returnable Valve) nozzle compatible with epoxy injector and having machined external end to receive outlet of Grouting Gun. Fix inside the hole by applying thixotropic epoxy adhesive to ensure complete sealing and allow curing the system for minimum of 8 Hrs before Grouting including nozzle projections, excess putty, if any, over concrete element by grinding, leveling and finishing the external surface, after completion of the work, etc. complete all as specified and directed. |
| 97 | Epoxy grouting: Grouting, injecting two part, low viscosity, moisture insensitive injectionliquid, based on high strength epoxy resin by pressure and using pressure epoxy injector with accessories till nozzle refused to accept the grout including mixing of grout having following properties:- (i) Mixed Density 1.1 kg/l (at +27°C); Viscosity ~ 250 mPas at +30°C and should comply according to ASTM C 881, Type II and IV, Grade-1, Class E+F (ii) Compressive strength >= 70 N/sqmm (7 days) according to ASTM C 579; Tensile Strength ~ 50 N/sqmm (after 7 days at +30°C cure) (According to ASTM D 638); Tensile Modulus ~ 2000 N/sqmm (after 7 days at+30°C cure) (According to ASTM D 638); (iii) Bond Strength ~ 10.8 N/sqmm (failure in concrete) after 14 days at +30°C cure; Flexural strength ~ 50 N/sqmm according to ISO 178. (iv) Seal the nozzle with thixotropic epoxy adhesive after the refusal of grout material from the nozzle. Note:- leakage through other nozzle or cracks are required to be monitored while grouting and such points to be sealed as and when required without any extra cost. (Mode of measurement: per kg of material consumed)Make: SG Corporation- Verdhaio LVG/ Pratham Enterprises- Impermo 4002/ Optimus Chemicals- OptyRE POLYG or equivalent. |
| 98 | M&L for removal of existing loose damage concretye, dust, oil, paint, grease, etc from structural member like roof slab, beam, column, chajja, etc exposed fully if any corroded steel in the repair area and remove all the scale and corrosion deposite and applying Dr fixit rust removal and Epoxy Zinc Primer over the cleaned steel bars if and pour the mixed Dr fixit micro concrete into a watertight shuttering after primed by one coat of Dr fixit Epoxy bonding. Thickness or depth of an area n. exc 10cm and all as per manufature instruction as specified. (Note - The rate included S&F of addition reinforcement bars if any required.) |
| 99 | Providing & fixing hard drawn MS steel wiremesh 80mm x 25mm with 3mm dia wire with Heavy duty nails, Fixing the mesh on the ceiling before shotcreting work. all as per direction of Engineer incharge |
| 100 | M&L For Chicken GI wire netting 0.90mm dia and 12mm mesh lathing to wood or metal studding, joists, etc. in walls, ceilings, stanchions, beams, etc. including all laps, cutting and waste complete all as specified and directed |
| 101 | Material and labour for providing pourable, shrinkage compensated, free flowing and self-compacting superior performance micro concrete Sikacrete 145IN factory design with selected cement, aggregate and other chemicals. Recommended water and coarse aggregate maximum 15% of bag to be added at site as per manufacturer instruction. Product should strictly meet the requirement of Compressive strength @28 days ~50 N/mm2 (ASTM C109)/ Flexural strength @28 days ~7 N/mm2 and Tensile adhesion strength @≥ 2 N/mm2 (28 days, +30 °C) (EN 1542) or as per manufacturer instructions and mixing concrete with mechanically electrically operated mixer machine Including necessary formwork , Shuttering and jacatingetc all as specified and directed. Make:-Mentioned in Appx \"B\" |
| 102 | Plaster: Providing and Applying Cement plaster: ready to mix cement plaster with high quality polymer additives with 4 Mpa compressive strength of average 15 mm thick over the entire surfaces including all tools and tackles etc complete. |
| 103 | S&F Window Canopy which is made with a durable polycarbonate/Glass/ fiber/acrylic sheet and steelbrackets for roof covering/cladding to wall, fixed with hold fast complete all as specified and directed by Engr-in-charge.(Note :As per Design approved by GE) |
| 104 | M&L for preparation of new steelsurfaces of any descriptionover 10 cm width / girth& applying 2 coat of synthetic enamel paintcomplete all as specified and directed by Engr-in-charge |
| 105 | M & LMild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed |
| 106 | M & L for RCC type M-25 Nominal mix using 20mm graded aggregates as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed by the Engineer-in-Charge. |
| 107 | M & L Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200m thick (Horizontal or sloping) complete all as specified and directed |
| 108 | Demolition of concrete block masonry built in cement mortar or cement lime mortar |
| 109 | M&L for Pre-cast cement concrete block masonry (Type C1, 1:3:6, 20mm aggregate) with solid blocks, exc. 10cm in width and setting in cement mortar (1:6), complete all as specified and directed. |
| 110 | S&F 25 mm size magnetic catches with Plastic body and striking plate including letting in and fixed complete |
| 111 | S & F in repairs stainless steel Kitchen plate rack of overall minimum size 650 mm x 600 mm and 250 mm deep, with partitions for small/large plates etc made out of stainless steel 0.80 mm thick fixed with rawl plug and CP steel screws complete, all as directed. |
| 112 | S&F PVC18 mm thick prelaminated solid board one sidedecorative choice lamination and other side plain fixed with SS screws for making kitchen cabinates including shelves ,cup board of rooms and other required as per gorund all as directed and as per manufacture instructions Make : Rajshree plasticwood Note : (1) colour choice of board as per directed by GE 2. |
| 113 | M&L block board, 19/20mm thick, grade 2 quality, interior grade, commercial type, fixed with screws to timber frame workas in cup board shutter/shelves/cabinet etc, complete, all as specified and directed. |
| 114 | M&Lfor 0.90mm thick decorative laminates \"Mica type 1 of surface finished,colour and pattern as approved, fixed with adhesive as per makers instructions. |
| 115 | S&F 25 mm size magnetic catches with Plastic body and striking plate including letting in and fixed complete |
| 116 | S&F continuous (piano) hinges 20mm & 12 MM width of flap, mild steel bright finish or electrogalvanised of complete all as specified fixed with CP steel screws. |
| 117 | Supply & fixing aluminium (extruded section body) Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed (IS Marked) complete all as per direction of Engineer- in-Charge |
| 118 | Dismantaling and taking down copper / aluminium point wiringany type / size complete with removing all connection and accessories such asswitches , sockets, ceiling rose,pendent holder,fan regulator any type , all type of fitting , batten , steel or PVC conduit , casing caping etc compele and making good the disturbed surface. |
| 119 | Taking down old and unserviceable sub main wiring any size / type / core incl earth wire complete with batten/conduit etc and making good the disturbed surface to match the existing disturbed surface all as directed by Engr-in-charg. |
| 120 | Taking down old and unsrevicablesheet metal enclosure , switch fuse unit , distribution bord any type /way / capacity including fuses,MCB\"s , insulator etc complete after removing all connection and making good the disturbed surface all as directed by Engr-in-charg. |
| 121 | M&L for Point wiring complete with FR PVC insulated unsheathed , 1100 V grade conforming to IS 694 ,1.5 Sqmm (Norminal area) multistranded ,copper conductor cable drawn through in non metallic rigid PVC conceled/surfaceconduit medium grade ,minimum 20 mm dia, ISI Marked,with sutaible size of 1 to 8 module metal flush boxes and back plate for mounting of modular switches/socket and regulators and including modular fornt plate with all acessories complete . |
| 122 | (a)One light point controlled by one way one switch SP 5 Amps ,240 V. |
| 123 | (b)One light point controlled by two 2 wayswitch SP 5 Amps ,240 V. |
| 124 | (c)One ceiling/exhaust fan point controlled by one way one switch SP 5 Amps, 240 V. |
| 125 | (d)One switch socket outlet 3 Pin, 5 Amps, SP on independent board. |
| 126 | (e)One switch socket outlet 3 Pin, 5 Amps, SP on sameboard. |
| 127 | (f) One bell / buzer point controlled by one push button switches on independentboard . |
| 128 | All as per the above item No 4 herein before but with 2.5 Sqmm cable for 3 Pin 5/15 Amps switch socket outlet. |
| 129 | S&F modular switch one way 6 Amps , 1 module type complete . |
| 130 | S&F modular switchtwo way 6 Amps , 1 module type complete . |
| 131 | S& f modular socket , 6 Amps , 2/3 pin combined 2 module complete. |
| 132 | S& f modularswitch socket combination, 6 Amps / 16 Amps , 2/3 pin combined 2 module complete. |
| 133 | S&F ceiling rose surface backlite 65 x 20mm size three terminal ISI marked complete |
| 134 | S&F Bell push6 Amps 1 module complete |
| 135 | S&F bellMulti music type ,240 Volt, Single PoleISI marked complete. |
| 136 | Supply and fixing LED lights fitting 1x 20 W, 220V,AC decorative box type with driver, holder including LED tube light connecting uptoPVC insulated 3 core flexible cable from ceiling rose to fitting drawn through in PVC flexible conduit including as per site requirementand 2 Nos ofround or square PVC bolck for fixing of FTL fitting complete all as per directed by Engr-in-charge. |
| 137 | Supply and fixing ofmirror light of capacity 1x10 Watt epoxy white powder coated CRCA sheet steel housing with acrylic diffuser gaskat with all fixing acessories complete all as specified and directed. |
| 138 | supply & fixing modular fan regulatorstep type , 1 module complete. |
| 139 | M&L for sub main wiring with two runs of 6 Sqmm (2x6 sqmm )1100 volts grade single core FR PVC insulated unsheathed multistranded copper conductorcableconfirming to IS-694 drawn through and including non-metalic PVC rigid conduit 25 mm dia ISI marked with all conduit accessories concealed in walls/roofs/floors etc with one run of 6 Sqmm (1x6 sqmm )single core FR PVC insulated unsheathed copper conductor cableas earth wire complete all as specified and directed.Note:- 2 runs of 6 Sqmm ,one run of 6 Sqmm( 2x6 sqmm + 1x6 sqmm ) cable and one meter of conduit will be measured as one unit again. |
| 140 | S&F sheet metal enclosures fordistribution board when MCB to be used SPN ( Single pole and neutral ) 8 way, 240 Volts, sheet metal powder coated, IP 42 protection with 200 Amps rated bus bar, double door typecomplete all as specified and directed. |
| 141 | Supply & fixing MCB DBs TPN vertical, Double door, with provision of MCCB as incommer , 4 way, flush in wall, including civil work to match the disturbed surface with existing complete all as specified and directed by Engr-in-charge |
| 142 | S&F MCCB of capacity 100 Amps , 415 Volts, rupturing capacity 16 KA complete. |
| 143 | S&F MCB SPN,40 Amps, 240 Volts, rupturing capacity 10 KA.\"C\" Seriescomplete. |
| 144 | S&F MCB SP, 5 to 32Amps, 240 Volts, rupturing capacity 10 KA \"C\" Series complete. |
| 145 | M&L , earthing complete for machinary / Equipment installed at power house / sub station with galavanised steel earth plate electrode of size 60 cmx 60 cmx 6 mm thick buried directly in ground ( earth pit not less then 2.25 m deep below the normal ground level ) with top edge of the earth plate not less then 1.5m below normal Ground level connected galvanised earth lead wire 4.0mm dia by means of bolts, nuts, washerws and check nutsall shown in electrical plate No.3 of SSR Part- I connected to main board / disribution board complete .Earthing GI lead and GI protection pipe 15 mm dia light grade upto 7.5 m from earth pit connecting to machinary/ equipment, testing point, all as specified and testing on completion all as per directed.Note :- (i) The unit rate shall also included for earth work in hard /dense soil , PCC type C-I (1:3:6) chamber , PCC 1:2:4 type B-I cover 50 mm thick reinforced with 8 mm dia TMT bars,150 mm c/c both ways, funnelwith watering pipe 20 mm dia medium graded , GI protection pipe light grade 15 mm dia and wire mesh complete in addition to items No. 1(a) to (e) of preamble (notes) under sub heading earthing specified on SI page No. 389 of SSR Part - II.(ii) Earthing lead and GI protection pipe beyond 7.5 mtrs will be measured and paid separatelly if required under appropriate Schedule.Note :- (i)Earthing shall be tested as specified incasul 19.137 of SSP PART - I 2009 , to the entire satisfication of Engr-in-Charge. (ii) On teting after complataion of earthing,if the desired earth resistance is not obatined the earthing wiil be re done by thecontractor at his on risk and cost to the entire satisfaction of the Engr - in - charge. |
| 146 | Supply and lay pipe uPVC pipeincluding fittingsof size 50 mm (2.0\") dia complete all as specified and directed. |
| 147 | Supply and lay pipe uPVC pipeincluding fittingsof size 25 mm (1.0\") dia complete all as specified and directed. |
| 148 | supply and fix ball valve25 mm dia including all fittings all as specfied and directed |
| 149 | Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete,complete all as specified and directed. |
| 150 | Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame All as specified and Directed. |
| 151 | S&f angle holder backlite with 1x10 Watt LED Bulb and making of connection with twin core flexible copper conductor from ceiling rose to fitting complete all as specified and directed. |
| 152 | Repair ofceling fan, Rewinding, painting , overhauling , greasingand replacement of U/S componante like capacitorto make functionalincludingprovision of 3 core flexiblecopper conductorfrom ceiling rose to fan complete all as specified and directed . |
| 153 | Taking down electric meter , geyser,ceiling fan and refixing after complation of work and connecting from ceiling rose including minor parts nuts ,bolts and complete all specified and directed. |
| 154 | NOTE APPLICABLE FOR ALL ITEMS :- If rate quoted for similar/identical items in same part of Sch ‘A’ is at variance, the lowest rate quoted shall only be considered for payment to the contractor. |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
| 5 | Click here to download tender document | Tender Documents |
| 6 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2025 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
