Sales : +91-777 804 8217
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 06-01-2026 | Bid Auto Extn Corrigendum | Bid Auto Extn Corrigendum | 13-01-2026 |
| Sl. No. | Item Description |
| 1 | Taking down carefully existing bitumenous membrane/tarfelt treatment any description and removing rubbish out of defence land all as specified and directed.Note:Quoted rate deems to be inclusive of removing all loose plaster. |
| 2 | Demolition of concrete (unreinforced) of any description and in any position not otherwise specifically provided for all as specified and directed. |
| 3 | M & L for Providing, cement concrete type B1 1:2:4 (20mm graded aggregate) in roof kerbs ,padding concrete or mud stops, rounded or chamfered on edges all as specified and directed. |
| 4 | M & L for rendering 15 mm thick (minimum) in CM 1:4 with liquid waterproofing compound (200ml per bag of cement used) on roof surfaces, parapets, facias etc., all as specified and directed.Note :- (i) Waterproofing compound shall be measured and paid separately.(ii) Quoted rate include for hacking over roof, parapet, facia surfaces for proper bonding of plaster/PCC. |
| 5 | M & L for waterproofing on roof including flashing and junctions of parapet, kerb, wall etc as under :-(a) Laying a layer of APP based polymeric membrane, 3mm thick (minimum), weighing not less than 3.60 kg/sqm prefabricated fibre layer waterproofing membrane reinforced with polyester non woven fabric (weighing not less than 160gms/sqm) shall be applied over compatible primer (oil based) at 0.7 litre/sqm of density at 25 degree centigrade 0.87-0.89 kg/litre and viscosity 70-160 cps or cold sticker, application of APP modified membrane shall be by torch application. The overlaps shall be minimum 150mm on the transverse direction and 100mm on the longitudinal direction.(b) APP membrane,Primer and bitumastic aluminium paint shall be of same brand.(c) For vertical surfaces of parapet,wall etc. app membrane shall be tucked into groove and sealed with silicon sealant(full width/depth of groove) i.e. \"Dowsil 789 weatherproof silicon sealant\" using gun.(d) aluminium paint shall be paid separately. |
| 6 | Supply only liquid water proofing compound |
| 7 | M & L for applying solar reflective bitumastic aluminium paint at the rate 0.15 Kg per sqm over exposed app membrane surfaces all as specified and directed. |
| 8 | Disconnecting existing tanks, setting aside (or lowering if required) for repairs exc 500 n exc 1000 litre, cleaning, etc. and hoisting if required reconnecting and refixing in position all as specified and directed.. (Cleaning repairing, etc. measured separately) |
| 9 | Dismantling water tanks of capacity Exc 500 Ltrs but n. exc 1000Ltrs and removing to from site or to store complete all as specified and directed. |
| 10 | S & F Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position of capacity 1000 ltr all as specified and directed. |
| 11 | S & F in repairs Ball valves, 20mm bore high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed all as specified and directed. (Minimum weight 2 1 0 gms.) |
| 12 | S&F in repairs 20 mmGun metal,globe or gate valves,with iron wheel head,screwed both ends for iron pipe all as specified and directed. |
| 13 | Taking up or down 20 mm GI tubes galvanized iron and connections and removing/shifting from site incl cleaningwhere directed complete all as specifed and directed |
| 14 | Taking up or down 15 mm GI tubes galvanized iron and connections and removing/shifting from site incl cleaningwhere directed complete all as specifed and directed |
| 15 | Re-fixing only 20 mm GI tubes galvanized iron and connections fixed to walls or laid in floor supplying & fixingnew fittings such as socket, bends, elbows nipple, union etc all as specified and directed of size complete all as specified and directed |
| 16 | Re-fixing only 15 mm GI tubes galvanized iron and connections fixed to walls or laid in floor supplying & fixingnew fittings such as socket, bends, elbows nipple, union etc all as specified and directed of size complete all as specified and directed |
| 17 | S & F for 20 mm GI tubes medium grade, galvanized with iron all fittingsfixed to walls, ceiling and laid in floor of sizes complete all as specified and directed |
| 18 | S & F for 15 mm GI tubes medium grade, galvanized with iron all fittingsfixed to walls, ceiling and laid in floor of sizes complete all as specified and directed |
| 19 | Taking down chowkhats or frames with shutters(without taking off shutters from the frame) exc 1.5 sqm but n. exc 4 sqm each and making good the jambs,soffits of lintels etc. after fixing of new chowkhat or frame to match the existing surface complete all as specified and directedNote. Work is to be executed at any height and situation. |
| 20 | Taking down chowkat or frames with shutters (without taking off shutters from the frame)but n exc. 1.5 Sqm all as specified and directed |
| 21 | Taking down shutters exc 1 Sqm but n exc 2 Sqm complete all as specified and directed |
| 22 | Taking down MS window/ventilators frames with shutters of any size and any description,making good soffits,jambs,cills etc to receive new window/ventilators frame complete all as specified and as directed.Note : work is to be executed for high rise bldgs.Any damage during dismantiling of window shall be made good by contractor without any financial effect. |
| 23 | S & F aluminium (50 micron powder coated) frame for doors, windows, ventilators and glazed partition frame of any size with one or more rebates including joining cleat,beading,glazing clips and connected accessories as required for fixing etc.complete all as specified.Note :- work is to be executed for high rise bldgs. |
| 24 | S & F aluminium (50 micron powder coated) window, sliding type (3 track i.e. one wiremesh shutter & two glazed shutter) without sash bars,aluminium sections weighing 0.55kg/m including necessary joing cleats,glazing clips,rubber packing,anodised aluminium snap beading,screws,rollers anodised aluminium fittings required to windows fully functional complete all as specified and directed.Note:- The quoted rate shall include cost of supply and fixing SS wire cltoh 0.36mm nominal dia and average width of aperture 1.40 mm ,4.00 mm thick glazing forglazed shutter .only size of opening shall be measured for the purpose of payment.each shutter shall not be measured. |
| 25 | M & L for 3.0mm thick frosted sheet glass,ordinary quality and glazing with silicon gel in square n.exc 0.5sqm in each pancomplete all as specified and directed. |
| 26 | S & F Stainless steel wire cloth 0.36mm nominal dia of wire and average witdth of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.Note:- Work is to be executed at any height and situation. |
| 27 | Dismantling wrought iron or mild any description such as steel gate,steel frame works,purlins,rafter,railings,balusters and window guard bars and directed by engr-in-charge.Note:- work is to be executed at any height and situation. |
| 28 | S & F framed work as in grill, doors or gates of angle or other section with gusset plates,braces,etc. complete, drilled for fixing of steel sheeting or other coverings,doors,etc to be prepared for hanging or sliding with and inlcluding either hooks and hinges or steel hanging door fittings(exclusive of steel sheeting or other covering,running rails and guides) and hanging;also fastening and fixing Fe Grade 410W(Gde E-250) complete as specified and directed over and includingapplying two coats of synthetic enaml paint over a coat of primer complete all as specified and directed. |
| 29 | S & F steel work in trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.4923; 19979 grade YSt.-210 over and includingapplying two coats of synthetic enamel paint over a coat of primer complete all as specified and directed. |
| 30 | M&L for plain cement concrete 1:3:6 type C1 (using 20mm graded stone aggregate) as in in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands,plinth courses, string courses,lacing courses, parapets and railings upto 60 cm in height,copings, kneelers, apex stones,bed plates, kerbs not provided for in Item 04028, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed |
| 31 | S&F2nd class hardwood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed. |
| 32 | M&L for 2nd class hardwood exc 13 Sqcm and n exc 25 Sqcm Plain fillets square, rectangular or triangular in section, clean sawn, secured with nails or brads complete all as specified and directed |
| 33 | S&F IInd class hard wood factory made flush shutters 30mm thick, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed |
| 34 | M&L for factory made, 2nd class hard wood rail and style 35 mm thick, plain framed, panelled shutters (two panels) with lock rail and panel of 9 mm BWP commercial ply or 12 mm veneered partical board with commercial veneering on both sides. The size of rail and stile as per IS-1003 (Part-I), kiln seasoned and chemically pressure treatedcomplete all as specified and directed. |
| 35 | S&F IInd class hard wood factory made Glazed and skeleton shutters 35 mm thick, open rebated and prepared to receive glass, gauze, etc. (divided in to square with sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mi-tred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Sec-tion 8, cla-use 8.20 (a); supplied and fitted to chowkats complete all as specified and directed |
| 36 | M & LFactory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/ Chowkhat of size 50 x100 mm(single/double rebated) comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardantand fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. |
| 37 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) Prelaminated solid decorative type flush door shutter of size30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moistureproof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer -In- Charge.Note. :- The quoted rate is inclusive of the cost of SS butt hinges of 125 mm size. |
| 38 | S&F 1st class hard wood Small fittings such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including all necessary\" labours; articles n exc 200 cu. cm each complete all as specified and directed |
| 39 | S & F Brass helical / ordinanry rat tail rod pattern door spring 300 mm including roller and roller plate complete fixed with welding all as specified( ISI Marked ) |
| 40 | S&Ffloor door stopper of aluminium alloy body & tongue, anodised, with hard drawn steel spring of 150mm size fixed in floor complete all as specified and directed. |
| 41 | S&F staineless steel butt hinges 100mm size medium weight complete all as specified and directed |
| 42 | S & F 200mm size aluminium anodised,barrel tower bolts of extruded section and fixed complete all as specified and directed. |
| 43 | S & F extruded aluminium alloy handles, 125mm size, fabricated type, anodised complete all as specified and directed. |
| 44 | S & F 300 mm size aluminium alloy,anodised,sliding door bolt with hasp,staple(bolt type) and fixing clips of sheet,cast or extruded sections and fixing bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed. |
| 45 | Dismantling floor hearth or wall tiling including cement mortar bedding (But not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed. |
| 46 | M & L for Non - skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed |
| 47 | M & L for Glazed ceramic tiles in vertical surface 450x300x7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10mm thick backing coat in CM 1:4 complete all as specified and directed. |
| 48 | M & L for 8-10mm thick double charged vitrified tile ,area of each tile not exceeding 0.36 Sqm as in flooring,laid in any shape/pattern over and including 15mm thick screed in CM 1:6 asfloors,set & jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tile. |
| 49 | M & L for 8-10mm thick double charged vitrified tile ,area of each tile not exceeding 0.36 Sqm as in skirting,laid in any shape/pattern over and including 10mm thick screed in CM 1:4 as skirting,set & jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tile complete all as specified and directed. |
| 50 | M & L for 40 mm thick PCC 1:2:4 typeB0 (using 12.5 mm stone aggregate) as in levelling course to flooring complete all as specified and directed. |
| 51 | Dismantling of stone slabs of any descripation or thickness in floors, aprons etc laid bedded & pointed in any mortar complete all as specifed and directed complete all as specified and directed |
| 52 | M&L for 18 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed. |
| 53 | M&L forhand cut cudappa stone slab 20-25 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete Note: screed bed layer measured seperately complete all as specifed and directed |
| 54 | Rounding to edges of stone slabs one edge such as insteps cooking platform and other similar work complete all as specified and directed |
| 55 | M & L for fixing in repairs 25 mm bore matt finish stainless steel(SS-304 grade) curtain rod best quality as approved by Engr-in-charge over and including suitable projecting type brackets,end finals,socket for dead ends of pipe as the case may be.complete all as specified and directed. |
| 56 | S & F stainless steel Soap dish of standard size with screws complete all as specified and directed |
| 57 | M&L for special treatment to sunken portion with 10mm thickplaster in CM 1:4by using Ditachment DM 1% by weight of cementand surface made smooth after curing period two coat of Ditachment DS shall be applied @2.50 Kg/Sm. The paste like consistancy like is madeby using 2.5 Kg of Ditachment DS powder in one litre of admixture (Theadmixture is made by dissolving 1 part by volume ofNafufill SBR & 4 partbyvolume of water). After 7 days curing, testing shall be done by flooring for72 hours. Finally protective plaster coat of 10mm thick in CM 1:4 shall done by using Putz Ditachment 1% by weight of cement over layer of Detachment DS. All joints of CI Pipe, Nahani trap, WC connectionetc. shall be filled by mixture of cement, fine sand and 10% Nafufill SBRby weight of cement 32mm dia 450mm long GI Spout light grade shall be providedin all sunken slabs to drain off water complete all as specified and directed |
| 58 | M and L for repair to broken edges of RCC chajjas,roof projections,fins,facia and similar works by dismantling of loose and damaged/disintegrated portion of edges with any cross sectional area with cement mortar 1:4 or cement concrete 1:1.5:3 type A0 and chicken wire mesh with nails to hold fresh mortar and concrete including necessary formwork and scaffolding for work upto 2 storey buildings and finishing the surfaces to the entire satisfaction of Engr-in-charge. |
| 59 | Demolition of brick work or stone boulder masonry built in cement mortar or cement lime mortarincluding all quoins, arches, pillers etc but includingashlar facings, dressed stone work and precast concrete articles complete all as specified and directed |
| 60 | M and L for brick work fly ash brick with old size bricks straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and as directed. |
| 61 | M&L for brick work with fly ash bricks straight or curved on plan to any radius in half brick thick wall built in CM (1:4) complete all as specifed and directed |
| 62 | Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; Note. The quoted rate shall include cost of providing PCC 1:2:4 to the sides of paver path/hardstanding as per standard engineering practice to the entire satisfaction of Engr-in-charge. |
| 63 | M & L for 20-25 mm thick Rough shahabad stone slab as in flooring/Plinth protection over and including 15 mm thick screed bed in CM 1:6,set and jointed in neat cement slurry and pointed in CM 1:4 complete all as specified and directed. |
| 64 | M & L 75mm thick cement concrete type D-2, 1:4:8 (using 40mm graded stone aggregate) in sub base of flooring/hard standing complete all as specified and directed. |
| 65 | M & L for broken stone/boulder as in Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed |
| 66 | M & L for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and directed |
| 67 | S and F in repairs Brass CP fancy type single lever Wash basin mixer (wall mounted) with popup waster for mixing hot and cold water with 450 mm long braided hoses including necessary fitting for connection screwed down for iron pipe and 15 mm borecomplete all as specified and as directed. |
| 68 | S & F in repairs brass CP wall mixer for mixing hot and cold water,screwed down for iron pipe 15mm bore complete all as specified and directed. |
| 69 | S & F in repairs brass CP long body sink mixer for mixing hot and cold water,screwed down for iron pipe 15mm bore complete all as specified and directed. |
| 70 | S & F in repairs 15 mm bore bib taps, fancy type, cast copper alloy, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed. |
| 71 | S & F in repairs Brass chromium plated shower rose 125mm size with swivel joint, including fixing to steel pipe or union 15mm bore complete all as specified and directed. |
| 72 | S&F in repairs Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm diapipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified. |
| 73 | S & F in repairs Brasschromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and directed. |
| 74 | S & F in repairs 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed |
| 75 | S & F in repairs 15mm bore stop valves, cast copper alloy, fancy type, chromium plated (angle type) screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed. |
| 76 | S & F in repairs 15 mm bore fancy type chrome plated Stop valves(concealed type), with long shank and cup,cast copper alloy,screwed down,high pressure,with crutch or butterfly handle,screwed both ends for iron pipe or for unions and fixed complete all as specified and directed |
| 77 | S&F in repairs 8mm thick glass shelf \"Corner\" type size 300mm x300mm including necessary brackets front edge of glass rounded and woulded with CP railing complete, fixed in repairs complete all as specified and directed. |
| 78 | S & F in repairs Sinks made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495 mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and directedNote:- quoted rate shall also include cost of waste pipe and sink coupling. |
| 79 | S & F in repairs PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed. |
| 80 | S&F 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers all as specified and directed by Engr in charge |
| 81 | S and F in repairs Vitreous china premium/ 1st quality wash down water closet wall hung EWC white/ ivory/off white (closed pattern incl all necessary accessories like rag bolts/ gel gasket /sheet cover etc. (excluding flushing cistern & flush pipe) complete in all respect all as specified. |
| 82 | S&F in repairs for 10 Ltrs capacityPVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including flush pipe and brackets complete all as specified and directed.Note :- The quoted rate deems to be inclusive of hdpe pipe for flushing cistern. |
| 83 | S& F in repairs Vitreous China wash basins white, flat back, size 550 x 400mm, including cutting for and pinning in ends of brackets or erecting stand and waste coupling 32mm of PTMT (Minimum weight45gms) half or full threaded fixed in repairs complete all as specified and directed. |
| 84 | S & F in repairs for Brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed of bore 32 .complete all as specified and directed. |
| 85 | S & F in repairskitchen plate rack made out of stainless steel 0.8mm thick complete of size not less than 750x750x200mm, duly assembled and fixed to wall with wall screws / fasterners all as specified and directed. |
| 86 | Taking down 100/75 mm dia PVC/CI sand cast soil, waste and vent pipes, in any length with or without etc in any position complete all as specified and directed |
| 87 | S & F PVC (SWR) pipe single socketed 110 mm bore, any in length with rubber ring joints fixed to walls complete all as specified and directed.Note:- The quoted rate deems to be inclusive of PVC fixing clampls. |
| 88 | S & F PVC (SWR) pipe single socketed 75mm bore, any in length with rubber ring joints fixed to walls complete all as specified and directed.Note :-The quoted rate deems to be inclusive of PVC fixing clamps. |
| 89 | S & F PVC (SWR) bends, any radius 75 mm bore with oval access door complete all as specified and directed. |
| 90 | S & F PVC (SWR) bends, any radius 110 mm bore with oval access door complete all as specified and directed. |
| 91 | S&F of PVC(SWR) branch piece,single(single Y) 110 mm dia equal or unequal complete all as specified and directed |
| 92 | S&F of PVC(SWR) vent cowl of 75/ 110mm bore complete all as specified and directed |
| 93 | S andF 110mm bore PVC (SWR) junction single-Tee (equal or unequal) with access door complete all as specified and as directed. |
| 94 | S andF 75 mm bore PVC (SWR) junction single-Tee (equal or unequal) with access door complete all as specified and as directed. |
| 95 | Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits,manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out soft/loose soil complete all as specified and directed |
| 96 | Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc 25 cm in soil complete all as specified and directed |
| 97 | Removing excavated materialsto a distance not exceeding 50 Mtr and depositing where directed at a level not exceeding 1.5 Mtr above the starting point complete all as specified and directed |
| 98 | Demolition of reinforced cement concerte as in cover slabs of manholes or septic tanks, soak pits etc. complete all as directed |
| 99 | M&L pre cast cement concrete 1:2:4 type B1 (using 20mm graded stone aggregate) asin manhole cover slabs set in cm 1:6 all s specified & directed |
| 100 | M & L PCC 1:4:8 type D2 (using 40 mm graded aggr) as in fdn filling and mass concrete complete all as specified and directed. |
| 101 | M and L mild steel TMT bars 10mm dia and over cut to length bend to shape required, including cranking, bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (anneled) not less than 0.9mm dia or securing with clips quality coinforming to IS complete all as specified and as directed. |
| 102 | Demolition of breaking updrain pipes of RCC or salt glazed ware set in CM dia up to 200 mm complete as specified and directed. |
| 103 | S&F reinforced concrete pipe, class NP2 laid and jointedcomplete with collars 200mm bore of pipe complete as specified and directed. |
| 104 | S&F reinforced concrete pipe, class NP2 laid and jointedcomplete with collars 150mm bore of pipe complete as specified and directed. |
| 105 | Demolition of Cement Concrete of any description in ground floor & paving n.exc. 15 cm thick(below or above ground level) |
| 106 | M&L cement concrete type C-21:3:6 ( 40 mm graded aggregate) as in foundation, filling and mass concrete complete all as specified and directed |
| 107 | M/L PCC 1:2:4 type B2 as in surface channels and drains & benching of manholes and finishing even and smooth with out using extra cement complete all as specified and directed. |
| 108 | M&L for plain cement concrete 1:3:6 type C1 (using 20mm graded stone aggregate) as in copingcomplete all as specified and directed |
| 109 | Cutting in to existing manholes forconnecting drain pipes making good to pipe and rendering cutting out existing benches for and forming branch channel (1/2 round or 3/4 section)in cement concrete (1:2:4) type B1 smooth finished and reforming benching as required for 150 mm internal bore pipe complete all as specified. |
| 110 | M&L for preparation of old painted steel surfaces and applying one coat of synthetic enamel paint , girth or width exc 10cm complete all as specified and directed |
| 111 | M & L for painting with two coats of synthetic enamel paint over a coat of pink primer on new wooden surfaces exc 10cm width or girth including preparation of wooden surfaces all as specified and directed by EIC. |
| 112 | M & L for painting with one coats of synthetic enamel paint on old painted wooden surfaces exc 10cm width or girth including preparation of wooden surfaces all as specified and directed by EIC. |
| 113 | Taking down cement plaster on brick or stone wall or ceiling etc including raking out joints hacking for keys scrubbing down with water etc. complete all as specified and directed |
| 114 | M & L for Rendering 10mm thick in cement mortar 1:6 on faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed. |
| 115 | M&L for rendering 15 mm thick cement mortar on brick masonary surfaces with cement mortar 1:4 finishedof external walls finished even and smooth without using extra cement complete all as specified and directed |
| 116 | M & L for 5 mm thick plaster in CM 1:3 to ceiling ,soffits and sides of beams,facias,cannopies,chajjas,shelves,cupboard etc. complete all as specified and directed |
| 117 | M & L for preparing newly plstered surfaces of wall and applying two coats of exterior emulsion paint over a coat of exterior primer complete all as specified and directed. |
| 118 | M & L for complete removal of existing treatment on wall surfaces and applying two coats of exterior emulsion paint over a coat of exterior primer complete all as specified and directed. |
| 119 | M & L for preparation of newly plastered surfaces of wall and applying two coats of distemper oil emulsion over a coat of primer over 1.5mm thick wall care putty complete all as specified and directed. |
| 120 | M & L for preparation of newly plastered surfaces of ceiling and applying two coats of distemper oil emulsion over a coat of primer over 1.5mm thick wall care putty complete all as specified and directed. |
| 121 | M & L for complete removal of existing treatment and applying two coats of distemper oil emulsion over a coat of primer over 1.5 mm thick wall care putty on wall surfaces complete all as specified and directed. |
| 122 | M & L for complete removal of existing treatment and applying two coats of distemper oil emulsion over a coat of primer over 1.5 mm thick wall care putty on ceiling surfaces complete all as specified and directed. |
| 123 | Dismantling wall and ceiling boards(fibre,pulp,insulation,etc.) or insulation boards/slabs/blankets,kitchen cabinets board any thickness, including cover fillets, frame etc. complete all as specified and directed |
| 124 | M & L Factory made 18 mm thick 100% Solid WPC(wood polymer composite) Prelaminated board of required size comprising of virgin PVC resin of K value value 57-60(suspension grade),Calcium carbonate and natural fibers(wood powders/rice husk/wheat husk) and non toxic additives,made from extrusion process WPC foam sheet single extruded(inner) with density not less than 650kg/cum,having good screw holding capacity(screw withdrawal strength of 200 N(Face) & 1100 N (Edge),minimum compressive strength of 50N/mm2,modulus of elasticity 850N/mm2 and resistance of spread of flame of class A category with property of being Termite/borer free.water/moisture proof,Fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed countersunk ss crews all as per direction of Engr-in-charge.Note :- The quoted rate shall also be deemed to be inclusive of suitble sshandles,autoclosing ss hinges,magnetic catcher,telescopic channel,butt hinges etc complete all as specified and directed. |
| 125 | M & L Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/ Chowkhat of size 60x30(single/double rebated) mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardantand fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge over and including M.S. hold fast/ lugs or SS dash fasteners complete all as specified and directed. |
| 126 | Dismantling Plain or corrugated steel sheeting of any gauge,thickness,including Nainital or similar pattern roof coverings complete all as specified and as directed. |
| 127 | S & F Prepainted Galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength 550 mpa as in roof covering/cladding to wall,fixed with self tapping screw complete all as specified and as directed. Note :- Gap between wall face and sheet if any shall be sealed using CM 1:3 with WPC.quoted rate deems to be inclusive of the same. |
| 128 | M & L for Plastering on walls in cement mortar 1:4 in patches not exc. 3 Sqm on the buildings upto four storied,including taking down old plastering on walls, any description including finishing the surface to match existing surfaces complete all as specified and directed. |
| 129 | Excavating in post holes (or similar holes) each n exc 0.5 cum in hard /dense soil, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n exc 50 m and making good surface complete all as specified and directed |
| 130 | M & L for walling of random rubble uncoursed, well bonded, bedded and solidly hearted, built in cement mortar 1:6 complete all as specified and directed. |
| 131 | M & L for walling of random rubble uncoursed, well bonded, bedded and solidly hearted, built in cement mortar 1:6 except stone complete all as specified and directed. |
| 132 | Extrafor hammer dressing to face stones with maximum depression on face from a straight edge not exc 20mm and dressing face beds and joints as specified to random rubble walling, uncoursed orbrought upto courses complete all as specified and directed |
| 133 | M&L for keyed pointing to random or polygonal rubble, uncoursed or brought upto coursein CM 1:4 complete all as specified and directed |
| 134 | Demolition reinforced cement concretetank capacityn.exc 12000 Ltrand removing the debris out of MOD land. |
| 135 | S & F aluminium(50 micron powder coated) window and ventilator shutters,side hung type without sash bars,aluminium sections weighing 0.55kg/m including necessary joing cleats,glazing clips,rubber packing,anodised aluminium snap beading,screws,anodised aluminium fittings such as peg peg stay/tower bolt 150 mm long(1nos),hinges type B-21,100 mm long(2 Nos),suitable handle(2 Nos per shutter) complete all as specified and directed by Engr-in-charge.Note :- The quoted rate shall include cost of supply and fixing SS wire cltoh 0.36mm nominal dia and average width of aperture 1.40 mm ,4.00 mm thick glazing for shutter.only size of opening shall be measured for the purpose of payment.each shutter shall not be measured. |
| 136 | M & L for Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65 x 125 mm (double rebated)comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardantand fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge |
| 137 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) Prelaminated solid decorative type flush door shutter (with provision of fixing mosquitto proofing i.e.SS wire cltoh 0.36mm nominal dia and average width of aperture 1.40 mm in decorative fashion as directed by GE) of size30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moistureproof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer -In- Charge.Note :- wire mesh door shutter shall be factory made. wirmesh shall be fixed between two wpc board of minimum thick 12mm. Quoted rate deems to be inclusive of all additional cost for cutting opening indoor shutter in size and shape(designer) as directed by Engr-in-charge, wastage and wiremesh beading etc,. The quoted rate is inclusive of cost of butt hinges 125mm size and wiremesh. For design and pattern sample kept at GE office/site shall be followed. |
| 138 | Supplying and laying of 16 mm(OD) CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in trenches/wall complete all as specifiedNote :- Internal plumbing shall be concealed. |
| 139 | Supplying and laying of 20mm(OD) CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in trenches/wall complete all as specified |
| 140 | S & F PVC (SWR) branch piece, double (double Y) equal or unequal 110 mm bore with access door all as specified and directed. |
| 141 | S & F PVC gully trap 125/110 mm setting and jointing in solven cement. Complete all as specified and as directed. |
| 142 | Dismantling of PVC rain/vent/waste pipe any bore |
| 143 | Taking down carefully copper/aluminium point wiring complete (light, fan, plug point & power complete alongwith fittings (switches, ceiling roses, tube light fittings, bulk head fitting regulator, sockets main switches, DB removing materials to store & making good of disturbed surfaces of wall/floors etc complete all as specified and directed |
| 144 | M&L for point wiring with 1.5 Sqmm(22/0.30mm) PVC insulated andunsheathed multistranded copper conductor cable, 1100 volts grade, ISI marked, FRLS type drawn through and including PVC concealed conduit (ISI marked) of adequate size and its accessories with sunk cast iron/pressed steel terminal boxes of size 1.2mm thick, with 3mm thickplastic laminated sheet cover of adequate size for one light or one fan point controlled by one switch incl 1.5 Sqmm (nominalarea) copper conductor cable (multistrand), FRLS type, PVC insulated and unsheathed with colour code earth wire connected to common earth dolly at one end and metalic bodies of luminaires/ fan at other end complete all as specified and directed for the following:- (a)One light point/ fan point controlled by one, one way swtich.Note :-Unit rate include for cutting chases for conduits and sinking for boxes and making good to wall, floors etc. |
| 145 | (b)All as per ser item No. 144 herein before but One 5 Amp 5 pin socket outlet point on same board with other switches including earth wire as specified. |
| 146 | (c)All as per ser item No. 144 herein before but with 2.5 Sqmm (36/0.30mm) PVC copper stranded cable FRLS type for one 15 Amp 6 pin socket outlet point including PVC cable 2.5 Sqmm FRLS type copper stranded conductor as earth wire as specified & connected to commen earth & earth terminals including boards for mounting purposes. |
| 147 | (d)All as per ser item No. 144 here in before but on independent board. |
| 148 | (e) All as per ser item No. 144 herein before but one light point controlled by 2 way switches. |
| 149 | (f) All as per ser item No. 144 herein before but one bell/buzzer point controlled by one push button. |
| 150 | Supply and fixing of switch modular type 6 Amps one way, 1 module,AC 230 Volts, shrouded terminal, ISI marked complete all as specified and directed. |
| 151 | Supply and fixing of modular type socket 6 Amps 3 pin round socket with child safety shutter (ISI marke), AC 230 Volts, shrouded terminals, smooth plug removal and insertion complete all as specified and directed. |
| 152 | Supply and fixing of switch modular type 16 Amps one way, 1 module,AC 230 Volts, LED based indicator, shrouded terminal, ISI marked complete all as specified and directed. |
| 153 | Supply and fixing of modular type socket 6 Amps/ 16 Amp 3 pin socket with child safety shutter (ISI marke), AC 230 Volts, shrouded terminals, smooth plug removal and insertion complete all as specified and directed. |
| 154 | Supply and fixing of modular type bell push 6 Amps, AC 230 Volts, LED based indicator, shrouded terminal, ISI marked complete all as specified and directed. |
| 155 | Supply and fixing of switch modular type 6 Amps two way, 1 module,AC 230 Volts, LED based indicator, shrouded terminal, ISI marked complete all as specified and directed. |
| 156 | Supply and fixing of modular type fan 8 step regulator, 100 watt, AC 230 Volts, 2module, laser marking complete all as specified and directed. |
| 157 | Supply and fixing of ceiling rose surface PVC 50mm dia 3 terminals including PVC mounting block white/ivory finish complete all as specified and directed |
| 158 | Supply and fixing invertor LED tube light fitting 20watt, 4 feet, PVC extruded batten complete with retrofit T8 Polycarbonate tube with connector block, etc. complete with all accessories pre-wired and including connecting up with three core twisted flexible copper conductor cable with suitable size complete all as specified and directed. |
| 159 | Supply and fixing replacement LED tube light fitting 10watt, 2 feet, CRCA batten complete with retrofit T8 Polycarbonate tube with connector block, etc. complete with all accessories pre-wired and including connecting up with three core twisted flexible copper conductor cable with suitable size complete all as specified and directed. |
| 160 | Supply and fixing LED light fitting, 10 Watt bulkhead light mounted type with metallic channel and white reflector, suitable for mirror fittings with connector block, etc. complete with all accessories pre-wired and including connecting up with three core twisted flexible copper conductor cable with suitable size complete all as specified and directed. Make- Havells Cat Part No LHEXBLP7PN1W004 or equivalent of C&S/ Philips. |
| 161 | Supply and fixing LED street lightfitting 30 watt complete with powder coated die cast aluminium compact,IP 65 protection complete with all accessories pre-wired and including connecting up with three core twisted flexible copper conductor cable with suitable size complete all as specified and directedNote :Adequate size of bracket / clamps, nut, bolts, washers, etcrequired at site is deem to be included in this item rates. |
| 162 | Supply and fixing in replacement of bell ding dong type AC, 230 volts, single phase complete all as specified and directed. |
| 163 | Material and labour in replacement of MS box of size 100x90x30 cm depth, dust proof with front opening hinged door both side, made out of 2mm thick MS sheet cubical type with powder coated painting for mounting of MCCB, DB\"s, electric meter etc inside the box fixed in wall by necessary cutting of wall of suitable size in concealed and making good the surface, by applying cement work, brick work and matching colour (Oil bond distemper) etc including dismantling of MS box with MCCB, DB\"s and electric meters and refixing the same MCCB, DB\"s and electric meters in new box carefully including necessary electric connection by suitable size of copper conductor cable of suitable length and testing complete all as specified and directed.Note : (a)Any plastering work involved while taking out old UNSV meter box and refixing the new meter box is deem to be included in this rate.(b)PVC flexible conduit required within the meter boxes is deem to be included in this item rates. |
| 164 | Supply and fixing in replacement of submain wiring with two single core PVC insulated unsheathed, multistranded flexible copper conductor 1100Volts grade, FRLS type, cables 6 Sqmm drawn through in and including rigid PVCcasing caping including 6 Sqmm 1100Volts grade, FRLS type, PVC insulated unsheathed multi stranded flexible copper conductor cable as continuous earth wire and connecting to common earth terminals complete all as specified and directed. |
| 165 | Supply and fixing in replacement of submain wiring with two single core PVC insulated unsheathed, multistranded flexible copper conductor 1100Volts grade, FRLS type, cables 10 Sqmm drawn through in and including rigid PVC heavy duty concealed conduits including 10 Sqmm 1100Volts grade, FRLS type, PVC insulated unsheathed multi stranded flexible copper conductor cable as continuous earth wire and connecting to common earth terminals complete all as specified and directed. Note :- (i)Two runs of cables and one run of continuous earting cable drawn in conduit will be measured as one length of sub main. (ii)PVC conduit and its accessories is deem to be included in this item rates.(iii) Unit rate include for cutting chases for conduits and sinking for boxes andmaking good to wall, floors etc. |
| 166 | Supply and fixing in replacement sheet metal enclosure (factory made), TPN Vertical Distribution Boards (MCCB Incomer) IP43 protection Double Door : Plain 4 way, MCCB + 12 modules with 200 Amps rated busbar all as specified and directed. |
| 167 | Supply and fix in replacement distribution board sheet metal enlosure double door shutter type factory made fixed flush with wall or outside on wall surface suitable for mounting isolators & MCB\"s 240volts, 100 Amp rated bus bar with front openable cover suitable for SP & N 8 ways all as specified & directed. |
| 168 | Supply and fix in replacement MCCB 125 Amp TP,415 volts 16KA complete all as specified and directed. Make - Hager CP No HDA125U or C&S/ Legrand. |
| 169 | Supply and Fixing in replacement of MCB DP/SPN 6-32 Amps, 230 Volts, 50 Hz with 10 KA complete all as specified and directedMake - Hager CP No NBN232N or Legrand/ ABB. |
| 170 | Supply and fixing in replacement of MCB SP 6-32 Amps, 230 Volts, 50 Hz with 10 KA complete all as specified and directed.Make - Hager CP No NBN132N or Legrand/ ABB. |
| 171 | Material & Labour in replacement of Earthing complete withgalvanised steel earth plate electrode 60cmx60cmx6.3 mm thickness burried directly in ground (earth pit not less than 2.25mtr deep below normal ground level) with top edge of earth plate not less than 1.5 mtr below normal ground level connected to and incl galvanised earth lead wire of 4.00mm dia by means of nuts & bolts, check nuts and washers of galvanised incl PCC pit of 1:2:4 type B-1, cover reinforced with XPMweightnot less than 4 Kg/Sqm and 6mm dia bar handle, earth pit angle iron frame of size 25mm x 25mm,excavation and earth work in anytype of soil, charcoal dust, salt, light grade GI watering pipe 20mm dia with funnel and wire -mesh and medium grade GI protection pipe of 15mm bore from top edge of earth plate upto main distribution board complete allto as shown in electrical plate No 3 of MES Sch 2009 (Part I) connected main switch board all as specified and testing on completion complete all as specified and directed. |
| 172 | Material & Labour for Taking down ceiling fan/ exhaust fan of any make and sizecomplete all as specified and directed.. |
| 173 | Material & Labour for hanging ceiling fan in position and re-commissioning the same including making electric connection complete all as specified and directed. |
| 174 | M&L for painting of ceiling fan and exhaust fan complete in site with synthetic enamel paint by spray painting including filling cavities with filter, one coat after cleaning of dust etc complete all as specified and directed |
| 175 | Supply, fixing, testing and commissioning of verticle mounting type electric water heater, storage type, 230volts, AC, 50 Hz, single phase, 5 star rated of capacity 25 ltrs with following specifications:-(i) Rated wattage in watt : 2000 Watt.(ii) Type of water heater : Closed type.(iii) Rated pressure : 0.8 mpa (Class I).(iv) Water head : 80 mtr.(v) Tank warranty : 10 Years.(vi) Outer body material : Engineering thermoplastic.(vii) Safety valve : 4 in 1 multifunctional valve.(viii) Thermostat : Capillery type.(ix) Heating element : Copper tube, Tubular type single pocket.(x) Insulation type : PUF insulation.(xi) Tank material : MS, with glass lined coating.(xii) Cord type/ material : 2.5 Sqmm, 3 core PVC insulation.(xiii) Maximum reheating type : 60 minuites.(xiv) Min. hot water output : 50 degree celcius. minimum.Note : 1. Rate including for grouting of fasteners, nuts and bolts are including in this item rate.2. Contractor shall furnish original tax invoice with manufacturers warranty 10 years for tank, 02 years for element and 02 years for product. |
| 176 | Fixing only exhaust fan and connecting up including connecting of cable from ceiling rose to exhaust fan complete all as specified and directed. |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
