Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | CIVIL WORKEarth work in excavation in foundation trenches in ordinary soil ( vide classification of soil item A) and disposal of excavated earth as obtained to a distance upto 50M including all lifts leveling ramming the foundation treanches, removing roots of trees, and shrubs all complete as per approved design, building specification and direction of E/I. |
| 2 | Earth filling in foundaion trenches and plinth in layers not exceding 150 mm thick well watered, rammed, fully compacted and fine dressed with earth obtained from excavation of foundation trenches within a lead of 50 M and lift of 1.5 M all complete as per building specification and direction of E/I. (mode of measurement compacted volume) |
| 3 | Excavating, supplying and filling of local earth (including royalty) bymechanical transport upto a lead of 5km also including ramming andwatering of the earth in layers not exceeding 20 cm in trenches, plinth,sides of foundation etc. complete. |
| 4 | Supplying chemical emulsion in sealed containers including delivery asspecified.2.34.1 Chlorpyriphos/ Lindane emulsifiable concentrate of 20% |
| 5 | Diluting and injecting chemical emulsion for POST-CONSTRUCTIONALanti-termite treatment (excluding the cost of chemical emulsion) :2.35.1 Along external wall where the apron is not provided usingchemical emulsion @ 7.5 litres / sqm of the vertical surface ofthe substructure to a depth of 300mm including excavationchannel along the wall & rodding etc. complete:2.35.1.1 With Chlorpyriphos/ Lindane E.C. 20% with 1%concentration |
| 6 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size) |
| 7 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. |
| 8 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level. 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size) |
| 9 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size). |
| 10 | Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete |
| 11 | Centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platform |
| 12 | Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers |
| 13 | Centering and shuttering including strutting, propping etc. and removal of form for Columns, Pillars, Piers, Abutments, Posts and Struts |
| 14 | Centering and shuttering including strutting, propping etc. and removal of form for Small lintels not exceeding 1.5 m clear span, moulding as in cornices, window sills, string courses, bands, copings, bed plates, anchor blocks and the like |
| 15 | Centering and shuttering including strutting, propping etc. and removal of form for Edges of slabs and breaks in floors and walls Under 20 cm wide |
| 16 | providing Tor steel reinforcement of 08mm. dia bars as per approved design and drawing inclusive carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of the wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I. |
| 17 | providing Tor steel reinforcement of 10mm. dia bars as per approved design and drawing inclusive carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of the wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I. |
| 18 | providing Tor steel reinforcement of 12mm. dia bars as per approved design and drawing inclusive carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of the wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I. |
| 19 | Providing designation 100 A brick work with fly ash lime brick (FLAG) confirming to IS 12894-1990 (9\"x4.5\"x3\") in C.M. (1:6) in foundation and plinth with approved uality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I. |
| 20 | Providing designation 112mm thick reinforcement designtion 100 A brick work with fly ash lime brick (FLAG) confirming to IS 12894-1990 (9\"x4.5\"x3\") in C.M. (1:4) in supertructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including cost of screening materials scaffoliding raking out joints to 15mm depth curing taxesand royalty ( but excluding theb cost of reinforcement) all complete as per building specification and direction of E/I. |
| 21 | Extra for providing and placing in position 2 Nos 6mm dia. M.S. barsat every third course of half brick masonry |
| 22 | Providing and fixing pressed steel door frames conforming to IS: 4351,manufactured from commercial mild steel sheet of 1.60 mm thickness,including hinges, jamb, lock jamb, bead and if required angle thresholdof mild steel angle of section 50x25 mm, or base ties of 1.60 mm,pressed mild steel welded or rigidly fixed together by mechanical means,including M.S. pressed butt hinges 2.5 mm thick with mortar guards,lock strike-plate and shock absorbers as specified and applying a coatof approved steel primer after pre-treatment of the surface as directedby Engineer-in-charge:Fixing with adjustable lugs with split end tail toeach jamb |
| 23 | Providing and fixing aluminium work for doors, windows, ventilatorsand partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved makeconforming to IS: 733 and IS: 1285, fixing with dash fasteners ofrequired dia and size, including necessary filling up the gaps atjunctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free,straight, mitred and jointed mechanically wherever required includingcleat angle, Aluminium snap beading for glazing / paneling, C.P.brass / stainless steel screws, all complete as per architecturaldrawings and the directions of Engineer-in-charge. (Glazing, panelingand dash fasteners to be paid for separately) Anodised aluminium (anodised transparent or dyed to required shade according toIS: 1868, Minimum anodic coating of grade AC 15)Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 24 | For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittingsshall be paid for separately) Powder coated aluminium (minimumthickness of powder coating 50 micron) |
| 25 | Providing and fixing glazing in aluminium door, window, ventilatorshutters and partitions etc. with EPDM rubber / neoprene gasketetc. complete as per the architectural drawings and the directions ofengineer-in-charge . (Cost of aluminium snap beading shall be paidin basic item):With float glass panes of 5 mm thickness (weight notless than 12.50 kg/sqm) |
| 26 | Filling the gap in between aluminium frame & adjacent RCC/ Brick/Stone work by providing weather silicon sealant over backer rod ofapproved quality as per architectural drawings and direction ofEngineer-in-charge complete |
| 27 | Supplying, fitting and fixing 35mm thick solid core type non-decorative single leaf flush door shutter in door and windows with black board core blended with high quality phenol formal dehydes synthetic resine both side commercial veneered of standard make with oxidised iron fittings such as hinges, towerbolts, handle, cleat and sand blocks and taxes all complete as per building specification and direction of E/I. |
| 28 | Supplying, fitting and fixing 35mm thick solid core type non-decorative double leaf flush shutter in door and windows with black board core blended with high quality phenol formal dehydes synthetic resine both side commercial veneered of standard make with oxidised iron fittings such as hinges, towerbolts, handle, cleat and sand blocks and taxes all complete as per building specification and direction of E/I. |
| 29 | Providing and fixing aluminium extruded section body tubular typeuniversal hydraulic door closer (having brand logo with ISi, IS : 3564,embossed on the body, door weight upto 36 kg to 80 kg and door widthfrom 701 mm to 1000 mm), with double speed adjustment with necessaryaccessories and screws etc. complete |
| 30 | supplying fitting and fixing aluminium fittings of approved quality and make to doors and eindows all complete as per building specification and direction of E/I.300mm sliding door bolt |
| 31 | supplying fitting and fixing aluminium fittings of approved quality and make to doors and eindows all complete as per building specification and direction of E/I.250mm sliding door bolt |
| 32 | Providing and fixing aluminium hanging floor door stopper, ISI marked,anodised (anodic coating not less than grade AC 10 as per IS : 1868)transparent or dyed to required colour and shade, with necessary screwsetc. complete. Twin rubber stopper |
| 33 | Providing and fixing aluminium casement stays, ISI marked, anodised(anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. |
| 34 | Providing and fixing bright finished brass 100 mm mortice latch andlock, ISI marked, with six levers and a pair of anodised (anodic coatingnot less than grade AC 10 as per IS : 1868) aluminium lever handles of approved quality with necessary screws etc. complete. |
| 35 | Providing and fixing aluminium tubular handle bar 32 mm outer dia,3.0 mm thick & 2100 mm long with SS screws etc .complete as perdirection of Engineer-in-Charge. Powder coated minimum thickness 50 micron aluminium tubular handle bar |
| 36 | Steel work welded in built up sections/ framed work, including cutting,hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works |
| 37 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete |
| 38 | Providing and fixing precoated galvanised iron profile sheets (size,shape and pitch of corrugation as approved by Engineer-in-charge)0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 micronsepoxy primer on both side of the sheet and polyester top coat 15-18microns. Sheet should have protective guard film of 25 micronsminimum to avoid scratches during transportation and should besupplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling /self tappingscrews of size (5.5x 55 mm) with EPDM seal, complete upto anypitch in horizontal/ vertical or curved surfaces, excluding the cost ofpurlins, rafters and trusses and including cutting to size and shapewherever required. |
| 39 | Providing and laying 25mm thick kotah stone slab flooring of approved size texure and colour over 19mm thick base of lime mortar (1:1:1) (limeputty:surkhi:coarse sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing to granolithic finish with approved quality of carborandum stone including cost of curing, taxes and royalty all complete as per building specification and direction of E/I. (iv) 600X600 mm size |
| 40 | Providing and laying 25mm thick kotah stone tiles in risers of steps skirting and pillars of approved size texure and colour laid over 12mm thick cement mortar (1;30 and joined with grey cement slurry mixed with pigment to match the shade of the slab including rub bing to granolithic finish with approved quality of carborandum stone including cost of curing, taxes and royalty all complete as per building specification and direction of E/I. |
| 41 | Providing and fixing 1st quality ceramic glazed floor tiles conforming toIS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. |
| 42 | Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc., complete. |
| 43 | Providing and laying Doublecharge vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622 / ISO 13006 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm . |
| 44 | Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & anufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Size of Tile 600 x 600 mm |
| 45 | Water proofing for Old and New Roof Slab :- Providing and laying water proofing treatment on roof slab by applying two Component, factory designed, ready to use, acrylic modified flexible |
| 46 | Covering of treated surface with PCC :- Providing 50 mm thick Cement Concrete M20(1:1.5:3) maintaining slope in alternate 2 mt x 2 mt panels with aaproved quality of stone chips of 20 mm |
| 47 | Providing and filling of 6 mm thickGroove between 50 mm PCC Panels with 6 mm thick 25 mm deep thermocol strip and filling the rest 25 mm with Polysulphide Sealant (Poring Grade)as per |
| 48 | Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2coarse sand : 4 stone aggregate 10 mm and down gauge), includingfinishing with cement mortar 1:3 (1 cement : 3 fine sand) as perstandard design : In 75x75 mm deep chase |
| 49 | Providing 12mm cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I. |
| 50 | Providing 19mm thick water proof cement plaster (1:3) with clean coarse sand of F.M. 1.5 with 5% cico or any other approved water proofing compound including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I. |
| 51 | Providing 6mm cement plaster (1:4) in celling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I. |
| 52 | Providing and applying white cement based putty of average thickness1 mm, of approved brand and manufacturer, over the plastered wallsurface to prepare the surface even and smooth complete |
| 53 | Distempering with 1st quality acrylic distemper (ready mixed) havingVOC content less than 50 gms/litre, of approved manufacturer, ofrequired shade and colour complete, as per manufacturer\"sspecification. Two or more coats on new work |
| 54 | Finishing walls with Premium Acrylic Smooth exterior paint withSilicone additives of required shade New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) |
| 55 | Providing precast cement concrete Jali 1:2:4 (1 cement : 2 coarsesand(zone-III) : 4 graded stone aggregate 6mm nominal size ), reinforced with 1.6 mm dia mild steel wire, including centering and shuttering, roughening cleaning, fixing and finishing in cement mortar 1:3 (1 cement: 3 fine sand) etc. complete, excluding plastering of the jambs, sills and soffits. 40 mm thick |
| 56 | SAPTIC TANKEarth work in excavation in foundation trenches in ordinary soil ( vide classification of soil item A) and disposal of excavated earth as obtained to a distance upto 50M including all lifts leveling ramming the foundation treanches, removing roots of trees, and shrubs all complete as per approved design, building specification and direction of E/I. |
| 57 | Extra for earthwork in hard soil as per specification and direction of E/I. ( vide classification of soil item-B) |
| 58 | Providing coarse clean sand in filling in in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials labour, royalty and taxes all complete as per building specification and direction of E/I (Mode of measurement compacted volume) |
| 59 | Providing designation 75B brick work in C.M (1:6 ) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar, joints cost of screening materials raking out joints to 15mm depth , curring , taxes and royalty all complete as per builiding specification and direction of E/I. |
| 60 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:2:4 (1 Cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 40 mm nominal size) |
| 61 | Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete |
| 62 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size). |
| 63 | Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers |
| 64 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size). |
| 65 | Centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platform |
| 66 | providing Tor steel reinforcement of 10mm,12mm,& 16mm. dia bars as per approved design and drawing inclusive carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of the wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I.(a) 10mm (TMT coil Fe 500) (only valid for Tata (Tiscon), SAIL, JSPL,Electrosteel Steels Ltd. Bokaro and Vizag (RINL)} |
| 67 | providing Tor steel reinforcement of 10mm,12mm,& 16mm. dia bars as per approved design and drawing inclusive carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of the wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I.(b) 12mm (TMT coil Fe 500) (only valid for Tata (Tiscon), SAIL, JSPL,Electrosteel Steels Ltd. Bokaro and Vizag (RINL)}) |
| 68 | Providing designation 75B one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/I. |
| 69 | Providing 12mm cement plaster (1:3) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I. |
| 70 | Providing 1.5mm cement punning including curing, carriage of water with all leads and lift as per building specification and direction of E/I. |
| 71 | SANITARY INSTALLATIONSSupplying, fitting and fixing40mm high vitreous white glaze earthen E.W.C. with \"p\" trap of parry Hindustan or any other approved I.S.S make including supplying and fixing 15 litres C.I mosquito proof low down flushing cistern of approved make with complete fittings with C.I handle and R.S or bracket with telescopic flush pipewith brass coupling and plumbers joints spindle stop cock of approved quality weight not lessthan 450 grams 15mm P.V.C alkathene pipe 45cm. long with brass coupling at both ends and white / black plastic solid stste seal and lead of commander/ cuckoo or other I.S.S. make with hinges or screws etc. painting pipe pipe and cistern etc, with 2coats of approved paint over a coat of red oxide piming, all complete as per specification and direction of E/I (B) E.W.C with \"S\" trapWith 10 lit low level PVC cistem |
| 72 | Supplying fitting and fixing vitreous white glazed earthen ware wash hand basin of Parry Hindustan or any other I.S.S approved make supported on painted C.I or R.S brackets 32mm C.I brass waste, 15mm dia C.I body brass spindel stop cock of approved quality of weight not less than 350 grams, 32mm PVCwaste pipe 750 mm long with brass coupling at one end and making plumber joints etc . all complete as per specification and direction of E/I. |
| 73 | Providing and fixing white vitreous china laboratory sink with C.I.brackets, C.P. brass chain with rubber plug, 40 mm C.P brass wasteand 40mm C.P. brass trap with necessary C.P. brass unions complete,including painting of fittings and brackets, cutting and making goodthe wall wherever required Size 600x450x200 mm |
| 74 | Providing and fixing white vitreous china flat back or wall corner typelipped front urinal basin of 430x260x350 mm or 340x410x265 mmsizes respectively |
| 75 | Providing and fixing P.V.C. waste pipe for sink or wash basin includingP.V.C. waste fittings complete Flexible pipe 32 mm dia |
| 76 | Providing and fixing PTMT liquid soap container 109 mm wide, 125mm high and 112 mm distance from wall of standard shape withbracket of the same materials with snap fittings of approved qualityand colour, weighing not less than 105 gms |
| 77 | Providing and fixing PTMT towel ring trapezoidal shape 215 mm long,200 mm wide with minimum distances of 37 mm from wall face withconcealed fittings arrangement of approved quality and colour,weighing not less than 88 gms |
| 78 | Providing and fixing C.P. brass bib cock of approved quality conformingto IS:8931 : 18.49.1 15 mm nominal bore |
| 79 | Providing and fixing C.P. brass long nose bib cock of approved qualityconforming to IS standards and weighing not less than 810 gms.18.50.1 15 mm nominal bore |
| 80 | Providing and fixing C.P. brass angle valve for basin mixer and geyserpoints of approved quality conforming to IS:8931 18.53.1 15mm nominal bore |
| 81 | Providing and fixing toilet paper holder : 17.34.1 C.P. brass |
| 82 | Providing and fixing flanged cleanout plug with MS flanged tail pieces, blind flang, 6mm dia nut & bolts, gasket and washers fixed to C I Pipe with drip seal joint complet in all complete including dutting and making good the wall and floor wherever required. with 100mm dia pipe |
| 83 | Providing and fixing uplasticised PVC connection pipe with brassunions : 45 cm length 15 mm nominal bore |
| 84 | Making khurras 45x45 cm with average minimum thickness of 5 cmcement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stoneaggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarsesand) and a coat of neat cement, rounding the edges and makingand finishing the outlet complete |
| 85 | Supplying fiting and fixing H.C.I pipes with ear of approved make confirming to I.S.I 1729 including supplying nails bobines short ,pieces, cutting loose collars , lead and yarns for making lead caulked joints, cutting pipes to sizes including earth work or scaffolding where necessery etc.all complete as per specification and direction of E/I.(a)100mm dia |
| 86 | Supplying fiting and fixing H.C.I pipes with ear of approved make confirming to I.S.I 1729 including supplying nails bobines short ,pieces, cutting loose collars , lead and yarns for making lead caulked joints, cutting pipes to sizes including earth work or scaffolding where necessery etc.all complete as per specification and direction of E/I.(b)75mm dia |
| 87 | Supplying fiting and fixing H.C.I pipes with ear of approved make confirming to I.S.I 1729 including supplying nails bobines short ,pieces, cutting loose collars , lead and yarns for making lead caulked joints, cutting pipes to sizes including earth work or scaffolding where necessery etc.all complete as per specification and direction of E/I.(b)50mm dia |
| 88 | Supplying and fixing H.C.I. fitting of apporved make confirming to I.S.S1729 including supplying nails bobines lead and yarns form making lead caulked joints, including earth work or providing scaffolding as the case may be all complete as per specification and direction of E/I.(A) H.C.I single junction with door but with out except socket (i) 100 mm dia (wt 10.5Kg app) |
| 89 | Supplying and fixing H.C.I. fitting of apporved make confirming to I.S.S1729 including supplying nails bobines lead and yarns form making lead caulked joints, including earth work or providing scaffolding as the case may be all complete as per specification and direction of E/I.(B) H.C.I. Heal rest bend(i) 100 mm dia (wt 5.5Kg app) |
| 90 | Supplying all tools and labour and cutting chajja, cornic for laying H.C.I pipes and making good the same as per specification and direction of E/I. |
| 91 | Cutting drain width wise above G.L for laying H.C.I pipe and restoring brick work in cement mortar (1:4) 12mm cement plaster in (1:4) with neat cement punning as per specification and direction of E/I. |
| 92 | Making holes in walls for laying H.C.I. pipes and restoring the same after pipe laying as per specification and direction of E/I. (i) 125mm dia |
| 93 | Supplying materials and labour for painting the exposed H.C.I pipes and fitting with 2 coats of approved paint over a cost of red oxideprimer etc.all complete as per specification and direction of E/I. (i)50mm dia |
| 94 | Supplying materials and labour for painting the exposed H.C.I pipes and fitting with 2 coats of approved paint over a cost of red oxideprimer etc.all complete as per specification and direction of E/I. (ii)80mm dia |
| 95 | Supplying materials and labour for painting the exposed H.C.I pipes and fitting with 2 coats of approved paint over a cost of red oxideprimer etc.all complete as per specification and direction of E/I. (iii) 100 mm dia |
| 96 | Providing fixing testing and commissioning of UPVC pipe SWR type B conforms to is 13592-1992 with all fitings such as bends, tees, elbow, Y offset, cleaning pipe door, clamps and steel structural supports etc including cutting the floors, walls and making food the same in cement concrete 1:2:4 & cement mortar 1:4. The wall thickness of pipe and technical characteristc conforms to IS :13692-1992 type B the fitting dimension conforming to IS 14735-1999. The jointing to be completed with rubber ring joint/solvent weld joint. 110mm (OD) SWR pipe |
| 97 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps,i/c cutting and making good the walls etc. 25 mm dia nominal bore |
| 98 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply, including allCPVC plain & brass threaded fittings, i/c fixing the pipe with clampsat 1.00 m spacing. This includes jointing of pipes & fittings with onestep CPVC solvent cement and the cost of cutting chases and makinggood the same including testing of joints complete as per directionof Engineer in Charge. Concealed work, including cutting chases and making good the walls etc.15 mm nominal dia Pipes |
| 99 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply, including allCPVC plain & brass threaded fittings, i/c fixing the pipe with clampsat 1.00 m spacing. This includes jointing of pipes & fittings with onestep CPVC solvent cement and the cost of cutting chases and makinggood the same including testing of joints complete as per directionof Engineer in Charge.Concealed work, including cutting chases and making good the wallsetc. 20 mm nominal dia Pipes |
| 100 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply, including allCPVC plain & brass threaded fittings, i/c fixing the pipe with clampsat 1.00 m spacing. This includes jointing of pipes & fittings with onestep CPVC solvent cement and the cost of cutting chases and makinggood the same including testing of joints complete as per directionof Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 25 mm nominal dia Pipes |
| 101 | Providing and fixing gun metal gate valve with C.I. wheel of approvedquality (screwed end) : 32 mm nominal bore. |
| 102 | Painting G.I. pipes and fittings with two coats of anti-corrosivebitumastic paint of approved quality : 25 mm diameter pipe |
| 103 | Providing and fixing G.I. Union in G.I. pipe including cutting andthreading the pipe and making long screws etc. complete (Newwork) : 32 mm nominal bore |
| 104 | Providing and fixing in position 25 mm diameter mosquito proofcoupling of approved municipal design |
| 105 | Constructing masonry Chamber 60x45x50 cm inside, in brick workin cement mortar 1:4 (1 cement : 4 coarse sand) for water metercomplete with C.I. double flap surface box 400x200x200 mm (inside)with locking arrangement and RCC top slab 1:2:4 mix (1 cement : 2coarse sand : 4 graded stone aggregate 20 mm nominal size) , i/cnecessary excavation, foundation concrete 1:5:10 ( 1 cement : 5fine sand:10 graded stone aggregate 40 mm nominal size) and insideplastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement complete asper standard design :18.37.1 With common burnt clay F.P.S.(non modular) bricks ofclass designation 7.5 |
| 106 | Providing and fixing square-mouth S.W. gully trap class SP-1complete with C.I. grating brick masonry chamber with water tightC.I. cover with frame of 300 x300 mm size (inside) the weight ofcover to be not less than 4.50 kg and frame to be not less than 2.70kg as per standard design: 180x150 mm size P type19.4.3.1 With common burnt clay F.P.S. (non modular)bricks of class designation 7.5 |
| 107 | Providing and laying non-pressure NP2 class (light duty) R.C.C.pipes with collars jointed with stiff mixture of cement mortar in theproportion of 1:2150 mm dia. R.C.C. pipe |
| 108 | Constructing brick masonry manhole in cement mortar 1:4 ( 1cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominalsize), inside plastering 12 mm thick with cement mortar 1:3 (1 cement: 3 coarse sand) finished with floating coat of neat cement andmaking channels in cement concrete 1:2:4 (1 cement : 2 coarsesand : 4 graded stone aggregate 20 mm nominal size) finished witha floating coat of neat cement complete as per standard design :19.7.1 Inside size 90x80 cm and 45 cm deep including C.I. coverwith frame (light duty) 455x610 mm internal dimensions,total weight of cover and frame to be not less than 38 kg(weight of cover 23 kg and weight of frame 15 kg) :19.7.1.1 With common burnt clay F.P.S. (non modular)bricks of class designation 7.5 |
| 109 | Constructing brick masonry road gully chamber 50x45x60 cm withbricks in cement mortar 1:4 (1 cement : 4 coarse sand) including500x450 mm pre-cast R.C.C. horizontal grating with frame completeas per standard design :19.27.1 With common burnt clay F.P.S. (non modular) bricks ofclass designation 7.5 |
| 110 | Providing and placing on terrace (at all floor levels) polyethylene waterstorage tank, IS : 12701 marked, with cover and suitable lockingarrangement and making necessary holes for inlet, outlet and overflowpipes but without fittings and the base support for tank. |
| 111 | FIRE FIGHTING WORKProviding storing, handing, shifting, installation, testing and commissioning of portable fire extinguishers as described belwo4.5 kg carbon dioxide extinguisher,IS marked with high pressure discharge tube, horn, control valve, CCE approved cylinder. |
| 112 | 6kg Mono Amminium Phosphate (ABC) type cartridge operated extinguishers |
| 113 | ELECTRICAL WORKWiring for light point /fan point/ exaust fan point / call bell point with 1.5 sqmm FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit, with modular type switch, modular plat, suitable size G.I. box etc. as required(iii) 25 mm dia nominalbore G.I. pipe |
| 114 | Power plug wiring in PVC conduit (2x4 sq.mm):-Wiring for light / power plug with 2x4 sq.mm FR PVC insulated copper conductor single core cable in surfface / recessed PVC conduit along with 1 Nos. 4 sq.mmFR PVC insulated copper conductor single core cable for loop earthing as requried. |
| 115 | Circuit /sub main wiring in PVC conduit :-Wiring for circuit / sub main wiring along with earth wire with the following size PVC insulated copper conductor ,single core cable in surface /recessed PVC conduit as requried.2x1.5 sq.mm + 1x1.5 sq.mm earth wire |
| 116 | Circuit /sub main wiring in PVC conduit :-Wiring for circuit / sub main wiring along with earth wire with the following size PVC insulated copper conductor ,single core cable in surface /recessed PVC conduit as requried.2x2.5 sq.mm + 1x2.5 sq.mm earth wire |
| 117 | TV cable in existing conduit :-Supplying and drawing co-axial TV cable RG-6 grade copper conductor, PE insulated , with PVC sheath in the existing surface/ recessed PVC conduit as requried. |
| 118 | S/F PVC conduit (PIPE) :-Supplying and fixing of following size PVC conduit along with accessories in surface/ recessed including cutting the wall and making good the same in case recessed conduit as requried. 25 mm |
| 119 | S/F PVC conduit (PIPE) :-Supplying and fixing of following size PVC conduit along with accessories in surface/ recessed including cutting the wall and making good the same in case recessed conduit as requried. 32 mm |
| 120 | S/F Modular type switch / socket :-Supplying and fixing following modular type switch /socket on the existing modular plate and switch box including connection but exculiding modular plate etc.as requried. 5/6 amps, one way switch |
| 121 | S/F Modular type switch / socket :-Supplying and fixing following modular type switch /socket on the existing modular plate and switch box including connection but exculiding modular plate etc.as requried. 15/16 amps, one way switch |
| 122 | S/F Modular type switch / socket :-Supplying and fixing following modular type switch /socket on the existing modular plate and switch box including connection but exculiding modular plate etc.as requried.5/6 amps, 3 pin socket outlet |
| 123 | S/F Modular type switch / socket :-Supplying and fixing following modular type switch /socket on the existing modular plate and switch box including connection but exculiding modular plate etc.as requried. 15/16 amps, 6 pin socket outlet |
| 124 | S/F Modular type switch / socket :-Supplying and fixing following modular type switch /socket on the existing modular plate and switch box including connection but exculiding modular plate etc.as requried.TV antenna socket outlet |
| 125 | S/F Modular type switch / socket :-Supplying and fixing following modular type switch /socket on the existing modular plate and switch box including connection but exculiding modular plate etc.as requried. |
| 126 | S/F Modular type blanking plate :-Supplying and fixing modular blanking plate on the existing modular plate and switch box exculiding modular plate etc.as requried. |
| 127 | S/F Modular boxes, base & cover plate :-Supplying and fixing following sizes / modules G.I. box along with modular base and cover plate for modular switches in recessed etc as requreied. 1 or 2 module ( 78mm x 78mm x 45mm ) |
| 128 | S/F Modular boxes, base & cover plate :-Supplying and fixing following sizes / modules G.I. box along with modular base and cover plate for modular switches in recessed etc as requreied. 4 / 5 module ( 78mm x 140mm x 50mm ) |
| 129 | S/F Modular boxes, base & cover plate :-Supplying and fixing following sizes / modules G.I. box along with modular base and cover plate for modular switches in recessed etc as requreied. 8 / 9 module ( 78mm x 230mm x60mm ) |
| 130 | S/F celling rose :- Supplying and fixing 2 pin 5 amp. Celling rose on the existing junction box/ wooen block including connection etc. as requried. |
| 131 | S/F Batten holder :-Supplying and fixing battrn / angle holder including connection etc as requried. |
| 132 | S/F ding dong call bell :-Supplying and fixing ding ding callbell sutiable for D.C / A.C single phase , 230 volts, complete as requried. |
| 133 | ITC fluorescent fitting directly on surface :-Intallation testing and commissioning of pre wired fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube etc. directly on celling / wall including connection with 1.5 sq. mm. FR PVC insulated copper conduit as requried. |
| 134 | ITC celling fan :- Installation, testing and commissioning of celling fan, including wiring the down rods of standerd leanth (upto 30 mm) with 1.5 sq.mm FR PVC insulated copper conductor single core cable etc. as requried. |
| 135 | ITC Exhaust fan upto 450 mm. sweep:-Installation of exhaust fan upto 450 mm. sweep in the existing opening, including making the holeto suit the size of the above fan, making good the damage, connection, testing, commissioning etc as required. |
| 136 | S/F T.P. MCB DB :-Supplying and fixing following way three pole and nutral sheet, MCB dstribution board 415 volts ,on surface/recess, complete with tinned copper busbar,nutral busbar, earth bar,din bar, detachable gland plate,interconnection, phosphatize and powder painted inculiding earthing etc.as required.(But without MCB/RCCB/Isolator)6way (4+18), Double door, Horizontle type |
| 137 | S/F \"C\" serise, MCB:-Suppling and fixing ,240 volts \"C\"serise miniature circuit breaker suitable for inductive loads of follong poles in the existing MCB DB complete with connections, testing and commisioning etc. as required . 6/32 amps, Single pole |
| 138 | S/F \"C\" serise, MCB:-Suppling and fixing ,240 volts \"C\"serise miniature circuit breaker suitable for inductive loads of follong poles in the existing MCB DB complete with connections, testing and commisioning etc. as required . 6/32 amps, TPN |
| 139 | S/F \"C\" serise, MCB:-Suppling and fixing ,240 volts \"C\"serise miniature circuit breaker suitable for inductive loads of follong poles in the existing MCB DB complete with connections, testing and commisioning etc. as required . 40 amps, TPN |
| 140 | S/F SPN RCCB :-Supplying and fixing following rating, double pole, (single phase and netural) 240 volts, residual current circuit breaker (RCCB), having asensitivity current up to 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63 amps |
| 141 | P/F M.V. danger notice plate:-Providing and fixing M.V danger notice plate of 200mm x 150mm, made of mild steel, at least 2mm thick and vitreous enamelled white on both sides and with inscription in single red colour on front side as requried. |
| 142 | Salt/ coke for pipe earth electrode :-Extra for using salt and coke for pipe earth electrode as requried. |
| 143 | P/F 6 SWG G.I loop earthing wire in surface /recess:-Providing and fixing 6SWG dia G.I. wire on surface or in recess for loop earthing, as required. |
| 144 | Supply & Laying of following size of 1.1kv grade multistranded copper conductor PVC insulated cable including lemination complete required exsisting cable tray.1C x 16sq mm PVC insulated cu wire including lemination etc |
| 145 | SITC OF floowing rating surface mounted LED tube light fitting suitable for 230V 50Hz, single phase supply etc. complete as required. 10/12W LED tube light |
| 146 | SITC OF floowing rating surface mounted LED tube light fitting suitable for 230V 50Hz, single phase supply etc. complete as required.20/22W LED Tube light. |
| 147 | SITC of 300 mm (12\"\") Exhaust Fan (Metal body) suitable for single phase 230 votls, 50Hz, AC supply compete with motor, louvers/shuffers etc. complete as required make- Usha//cromton/Hevels |
| 148 | Supply Installation, testing and commissioning of follwing size ceiling fan 3 blades confirming to IS:385:2019 including wiring the down rods of standard length (upto 30cm) with 1.5 sq.mm FR PVC insulated, copper wire suitable for 230V 50Hz, single phase supply etc. complete as required. 1200 mm (48\") BLDC 5 star rating 32W Ceiling Fan. |
| 149 | Carraige of Materials Sand 10km |
| 150 | Carraige of Materials Chips 22 km |
| 151 | Carraige of Materials Metal 22 km |
| 152 | Carraige of Materials Bricks 8 km |
| 153 | Carraige of Materials Local Sand Lead 3km |
| 154 | Add GST 18% |
| 155 | Add 1% Labour cess Please Enable Macros to View BoQ information |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2025 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
