Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Taking down cement plaster on stone masonry/Brick Masonry incl racking out joints, hacking for key scrubbing down with water and direction by Engr- In Charge. |
| 2 | M&L for 10 mm rendering in CM 1:6 on fair face of brick workor on concrete surface finished even andsmooth without using extra cement complete all as specified and directed. |
| 3 | M&L for 05 mm rendering in CM 1:3 on fair face of ceiling or on concrete surfaces finished even andsmooth without using extra cement complete all as specified and directed. |
| 4 | M&L for 15 mm rendering in CM 1:4 on fair face of wall or on concrete surfaces finished even andfair with water profinfing compound (WPC)complete all as specified and directed.(WPC Measured seprately) |
| 5 | M &L for Preparation of newplasteredsurface of walland applying twocoat of oil emulsion distemper of approved tints over a coat of interior wall primer complete all as specified and directed by Engineer-in-Charge.. |
| 6 | M&L for Preparation of newplasteredsurface of ceiling and applying two coat of oil emulsion distemper of approved tints on ceiling over a coat of interior wall/ceiling primer complete all as specified and directed by Engineer-in-Charge.. |
| 7 | M&L for preparation of new plastered surfaces ofexternal walls/RCC surfaces/soffits of chajjas/roof projection/cantilivers/balcony etc including cornices and applying Two or more coats of 100% Premium acrylic emulsion paint of required shade, , having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm,at any locationon old plastered or unplastered surfaces of walls including necessary scaffolding arrangement as required at sitecomplete all as specified and-as-directed. |
| 8 | M&L for complete removal of existing treatment incl preparation of wall surfaces and fill the crack of wall with crack filler pasteand applyingtwo coat of oil emulsion distemper of approved tints over a coat of interior wall primer, complete all as specified and directed by Engineer-in-Charge. |
| 9 | M&L 1-2mm thick wall care putty on External/Internal wall complete all as specified and-as-directed. |
| 10 | M&L for complete removal of existing treatment incl preparation of ceiling surfaces and fill the crack of ceiling with crack filler paste and applying two coat of oil emulsion distemper of approved tints on ceiling over a coat of interior wall/ceiling primer complete all as specified and directed by Engineer-in-Charge.. |
| 11 | M&L for complete removal of existing treatment incl preparation of wall surfaces and applying Two or more coats of 100% Premium acrylic emulsion paint of required shade, , having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm, at any locationon old plastered or unplastered surfaces of walls including necessary scaffolding arrangement as required at sitecomplete all as specified and-as-directed. |
| 12 | Preparation of old decorated wooden surfaces of any description, not otherwise described over 10cm width & girth and applying one coat of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge. |
| 13 | Taking down chowkat or frames with shutters (without taking off shutters from the frames) area not exc1.5 Sqm each and removing from sitecomplete all as specified and directed. |
| 14 | Taking down chowkat or frames with shutters (without taking off shutters from the frames) areaexc 1.50 sqm but n. exc 4 sqm complete all as specified and as directed. |
| 15 | Taking down shutters of any description exc 1 Sqm but not exc 2 Sqm eachandcomplete all as specified and directed. |
| 16 | S & FPressed steel frames made of MS sheet of 1.20mm thickness of size 165 x 60 mm for doors with single or double rebate including necessary fixing lugs, hinges, lock strike plate, hold fasts, PCC 1:3:6 type C-0 in fillinng inside frame & hold fasts etcincluding two coats of synthetic enamel paints over a coat of red oxide primer complete all as specified. (Note :- Distrubed protion of existing floor/ wall/ tile/ plaster etc during fixing of chowkhats shall be repaired to match with exisitng finish.Cost of the same will be included in this items).As approved by Accepting Officer |
| 17 | S & F Pressed steel frames made of MS sheet of 1.20mm thickness of size 105 x 60 mm for doors with single or double rebate including necessary fixing lugs, hinges, lock strike plate, hold fasts, PCC 1:3:6 type C-0 in fillinng inside frame & hold fasts etc including two coats of synthetic enamel paints over a coat of red oxide primer complete all as specified. (Note :- Distrubed protion of existing floor/ wall/ tile/ plaster etc during fixing of chowkhats shall be repaired to match with exisitng finish.Cost of the same will be included in this items).As approved by Accepting Officer |
| 18 | S&F powder coated aluminium, three track sliding window frame of section size 92.00x 31.75x1.3mm comprising of one No of fly proof shutter and two nos of glazed shutter frames of section size 40x18x1.3mm thick with necessary joining cleats, glazing clips, rubber gasket, anodised aluminium snap beading and connected locking arrangement all as specified and directed. (Notes. (i) Glass filling in panels of window and stainless steel wire mesh/wire cloth shall be demed to be included in the quoted rate for the item, ii) stainless steel wire cloth in panels of fly proof shutter shall be0.36mm nominal dia of wire and avg width of aperture 1.40mm, fixed with aluminium wire staples,. iii) Glass filling in panels of glazed shutter shall be 4mm thick tinted sheet glass of approved make and shade/tint (Make of aluminium sections powder coated: Make Jindal/INDAL/Hidalco). |
| 19 | M&L powder coated aluminium, frame for ,doors, window, ventilators, partion and sliding shutters etc (minimum thickness of powder coating is 50 mixcron) with one or more rebates including jointing cleat, aluminium snap beading 20 x 15mm, rubber gasket, glazing clip for fixing etc .complete all as specified. |
| 20 | S&F anodised aluminium grill made out of 7mm x 4.5mm w\"ide flat, square ractangular or similar section, fixed with channel of size 38mm x 12mm x 13mm (section 8778 complete all as specified including taking down(make: DECO GRILL No. DG 102 with aperture- 80mm or equipment as approved by GE. |
| 21 | Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube, supplying and fixing in opening as specified and as per drawing. |
| 22 | S & FFactory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification incl the fwg S & F As approved by Accepting Officer(a) Stainless Steel (304 Grade) Finished Butt Hinges 125mm -3 Nos per leaf(b) Stainless Steel (304 Grade) Finished Tower Bolt 200mm long - 2 Nos per leaf(c) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 Nos per leaf |
| 23 | Supply and fixing 35mm thick flush shutters, solid core construction, with block board core and plywood face panels,commercial type on both sidesa all as specifid and directed incl S & F fwg items As approved by Accepting Officer.(a)Stainless Steel (304 Grade) Finished Tower Bolt 200mm long - 2 Nos per leaf(b) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 Nos per leaf(c) Stainless Steel (304 Grade) Finished Sliding Door Bolt/Aldrop 16 x 300mm-1 No per leaf(d) Stainless Steel (304 Grade) Finished Floor Door Stooper- 1 No per leaf |
| 24 | S & F 35mm thick glazed and skelton shutters of 2nd class hard wood (factory made) open rebated and divided to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass etc size of members of shutter as specified in SSR-91 Pt-I section 8 clause 8.20 (a) kiln seasoned and chemically pressure treated all as specifeid including stainless steel 304 grade wire cloth ( 0.36mm nominal dia of wire and average width of aperture 1.40 mm ) and incl supply and fixing following items:-(a) Stainless Steel (304 Grade) Finished Tower Bolt 200mm long - 2 nos per leaf(b) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 nos per leaf(c) Stainless Steel (304 Grade) Finished Sliding Door Bolt/Aldrop 16x3000mm- 1 nos per leaf(d) Stainless Steel (304 Grade) Finished Floor Door Stooper- 1 nos per leaf |
| 25 | S&F for mild steel ordinary rat tail rod pattern spring 300mm size including roller & roller plate and incl welding complete all as specified and as directed. |
| 26 | M&L for preparation of new wooden surfaces of any description, over 10cm in width or girth, not otherwise specified with two coats of synthetic enamel paint over one coat of pink primercomplete all as specified and as directed. |
| 27 | Taking down shutters of any description exc 1 Sqm and n exc 2 Sqm each and refixing in same opening after cutting by chishel or hand saw, peeling by plane, fixing/ re-placing of hinges, repairing etc including all nales screws, pieces, small let in for making good where hinges, etc. have been removed from chowkhats or frames, shutters, etc. including painting or oiling to match, if required complete all as specified and as directed.(Note : Hinges shall be measured and paid separately) |
| 28 | S&F in repair 100mm size SS butt hinges and fixed to PVC frame /Wooden Frame and angle iron frame by necessary welding complete all as directed. |
| 29 | S & F in repairsSS bow handle, bearing ISI mark,fabricated type extruded section of 150mm longcomplete all as specified and as directed. |
| 30 | S&Fin repair SSbarrel tower bolts extruded section, 150mm size complete all as specified and directed |
| 31 | S & F in repairs SS sliding door bolts of 300mm long with hasp and staple(bolt type) and fixing clips of sheets ,cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy, bearing ISI mark.complete all as specified and directed. |
| 32 | S&F in repairs 140 mmfloor door stopper of SS and tongue , anodised ,with hard drawn steel spring ,fixed in floor complete all as specified and directed |
| 33 | S&F in repair Plain (white) PVC Celuka Ply Board in Door, Shelves for Cup Boards or Kitchen Cabinets, one side laminated, one side plain 18/19mm thick as reqd, jointed by means of PVC adhesive Solvent and fixed using self tapping SS screwscomplete all as specified and directed. |
| 34 | S&F in repair Plain (white) PVC Celuka Ply Board in Door, Shelves for Cup Boards or Kitchen Cabinets, both side plain 18/19mm thick as reqd, jointed by means of PVC adhesive Solvent and fixed using self tapping SS screwscomplete all as specified and directed. |
| 35 | S&F stainless steel silver chrome door handle 100mm long, suitable for fixing of brass screws inside of the board etc and fixed in repairs complete all as specified and directed. |
| 36 | S&F stainless steel frog hinges suitable for kitchen cupboards 22mm PVC celuka board etc for smooth movement and fixed in repairs, ompleter all as specified and directed. |
| 37 | S & F in repairs SS sliding door bolts of 150 mm long with hasp and staple(bolt type) and fixing clips of sheets ,cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy, bearing ISI mark.complete all as specified and directed. |
| 38 | S&F in repair Stainless steel wire cloth of 0.36mm nominal dia of wire and average width of aperture 1.40 mm and fixedd with tinned tacks or stainless steel wire staples or with wooden beads, stainless steel screws and nuts bolts etc complete all as specified. |
| 39 | S & F for Rotational moulded polyethylene water storage tanks of 1000 Litres capacity, (cylindrical vertical tanks with closed top) hoisted and fixed in position including making necessary arrangements for fixing inlet, outlet and over flow pipe and provision of wash out pipe etc including taking down existing tank complete . |
| 40 | S&F in repair Stainlesssteel tubing of 20 mm dia chromium plated min. 1.0 mm wall thickness as in curtain rod complete incl S&F 02 Nos stainless steel brackets & finials fency type, stops fixed with ss screws etc all as specified & directed.Note : For the purpose of mesurement and payment running length of curtain rod only shall be considered as approved by accepting officer. |
| 41 | S&F in repair for 16mm bore of CPVC of food grade pipes SDR 11 and plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including taking down or up existing GI tubing & connections all as specified and directed by Engr-in-charge. |
| 42 | S&F in repair20mm (OD) CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in trenches/ walls and ceilingincluding taking down or up existing GI tubing & connections all as specified and directed by Engr-in-charge. |
| 43 | Supply & Fixingin repair 25 mm bore tubes medium grade galvanized with all fitting such as Tee, elbows, sockets, unions, plugs, short lenghts etc and fixed complete to walls and ceilings or laid in floors of any length including taking down or up existing GI tubing & connections all as specified and directed by Engr-in-charge. |
| 44 | S&F in repair 15 mm dia bib tap,fancy type chromium plated cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed allasspecified anddirected. |
| 45 | S&F in repair 15mm bore CP fancy type stop valves/angle cock, cast copper alloy, screwed both ends for iron pipe orforunion complete all as specified and as directed. |
| 46 | S&f in repair 15mm bore pillar tap cast copper alloy fancy typewith capston heads, chromium plated screwed down high pressure, with or without letters Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipes and fixed all as specified and directed. |
| 47 | S&F in repair 110mm bore of PVC (SWR) pipes single socketed in any length with rubber ring joints laid on trenches or in floors /wall complete all as specified and as directed. |
| 48 | S&F in repairs 75mm bore PVC (SWR) floor trap plain with grating including jointing with solvent cement complete all as specified and as directed. |
| 49 | S&F in repair PVC (SWR) bend any radius 110mmcomplete all as specified and directed. |
| 50 | S&F in repairs 110 mm bore PVC [SWR] Junction single [single \"T\" or \"Y\"] equal or unequal, completeall as specified and as directed. |
| 51 | S & F in repair Vitreous china squatting pan of Orissa patten size 580 x 440 white colour including CI S/P trap long size as directedjoint run and leadfront or back inlet with integral footrest including connection to trap and to flushing pipe,anti-syphonage pipe, etc, fixed in repair complete and making good to floor in PCC 1:2:4 all as directed and specified. |
| 52 | S & F in repair Vitreous china premium/1st quality urinal half stall type, white colour, of size 465x355x265 mm incl providing and fixing plugs/brackets, bedding urinal against wall in CM 1:2, securing urinals to plugs with and incl S&F of all accessories for fixing as recommended by manufacturer like 60mm long brass secrews/fasteners/rag bolts etc, pointing urinal back in white cement; connecting for discharge pipe incl necessary packing, union complete all as specified. |
| 53 | S&Fin repair PVC connection 15mm bore length not less than 450mm long with both ends PTMT nuts complete all as specified. |
| 54 | S&F in repair Urinal spreader of PTMT any colour for fixing with 15mm diapipe. (Minimum weight 60gms). |
| 55 | S & F in repair Vitreous china premium/1st quality wash basin (under counter), white, size 550x400 mm including S&F all accessories as recommended by manufacturer complete fixed in position in all respect as per manufacturer\"s instructions and all as specified including all Waste fittings, brass,chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed, Note : The items for counter will be measured and paid separately. |
| 56 | S & F in repair Flushing cistern of PVC 10 ltr. cap. with dual flushing system, valveless syphonic action type, , low level, white/ivory/off white with inlet, ball valve, float and including brackets and connection to pipe etc. and incl all necessary accessories like rag bolts/gel gasket etc as recommended by manufacturer for fixing, packing and taking down existing of any description/size complete in all respect all as specified. |
| 57 | S&F in repairs Stainless steel gratings 100mm bore size fixed with cement motar. |
| 58 | S&F in repair sinks madeof stainless steel 1 mm thick kitchen or laboratory with plug , washer and wastes , including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe , overall size 495mmx420mm bowl size 410mmx330mmx160mm complete all as specified. |
| 59 | S&F in repairs chromium platedswivel shower roses with or without swivel joints,for fixing with 15mm pipe fixed all as specified |
| 60 | S&f in repair600X450 mm bevelled edge mirror of selected quality glass, mounted on 6 mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers |
| 61 | S&Fin repairs tubular towel rail, brass cromium plated, 20mm dia, D type, 60cm long between flanges completeall as specified and directed Engrs-In Charge. |
| 62 | Dismantling floor, hearth or wall tiling including cement mortar bedding, removing serviceable tiles to stores and removing debris outside the MD land. |
| 63 | S&F Non-Skid ceramic Coloured tiles 7 to 8mm thick (square / rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to matchincluding 15mm thick screed bed in CM 1:4 complete all as specified. |
| 64 | S&F Vitrified ceramic tiles in light shade10mm thick (square/ractangular) polished,area of each tiles exc 0.18 sqm but not exc 0.36 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to matchincluding 15mm thick screed bed in CM 1:4, complete all as specified and directed |
| 65 | Ditto as item above but as in skirting over cement mortar backing plaster in CM1:4 15mm thick |
| 66 | M&L for Glazed ceramic glossy finish tiles coloured in vertical surface 450X300X7mmin any pattern of light & dark/highlighters tiles etc as approved, on vertical surfaces such as in skirting/dado etc, set and jointed in cement slurry over & including 10 mm thick rendering in cement mortar (1:4) and pointed in white cement with pigment to match the colour of tiles complete all as specified. |
| 67 | Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any mortar.Note : Work will be in patches or in bulk |
| 68 | M & L for Machine cut kota stone slab flooring 20-25mm thick over, laid over cement screed base , jointed and pointedwith grey cement slurry mixed with pigment over 20mm thick cement mortar 1:6 screed bed to match the shade of the slab including rubbing and polishing complete all as specified and directed.Note : Work will be in patches or in bulk |
| 69 | M & L for Machine cut kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar over 10 mm thickcement plaster 1:3jointed and pointed with grey cement slurry mxed with pigment to match the shade of the slab including rubbing and polishing complete, all as specified and directed. |
| 70 | M & L for Granite of black / green / imperial red (colour as approved by Accepting Officer) of any type machine cut as in shelves/steps/counter tops, 20 mm thick, set and jointed in cement slurry over & including screedof 15 mm thick / rendering in cement mortar (1:4) and pointed in cement mixed with pigment to match the shade of slab or with suitable adhesive for fixing on unpolished kota stone slabs and including rubbing, cutting and mirror type polishing and bull nose on exposed sides complete all as specified .Note : Single piece should be used in steps/cills/jambs/shelvesor equivalentas approved by accepting officer. |
| 71 | Rounding to edges , one edge, of stone slabs / kota stone, such as in steps, cooking platform, and other similar situations complete all as specified. |
| 72 | M&L for 25mm thk PCC 1:2:4 type B0 using 12.5mm graded stone aggregate as in subbase of floors & finishing the surface even & smooth without using extra cement. |
| 73 | Demolition of stone / boulder masonry walling built in cement mortar including all quoins arches pillars etc and removal unserviceable materials, debris, rubbish to out side MD land complete all as specified and as directed. |
| 74 | M&L for precast-cement concrete block masonary with solid blocks type C-1 ,1:3:6 (20mm graded aggregates) exc 10 cm in width and setting in CM 1:4 ,complete all as specified and directed |
| 75 | Dismantling of plain or corrugated steel sheets in roof coverings any type complete all as specified & directed by Engineer in charge. |
| 76 | S&FPre- painted galvaiume aluminum zinc coating GI based corrugated steel sheet 0.5 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping crews as specified complete all as specified and directed |
| 77 | S&F for hollow,rolled sections as in main and cross beams, column, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates conf to Fe-410-w or E -250 quality A complete all as specified and directed. |
| 78 | M&L for applying two coats of synthetic enamel paint over a coat of red oxide primer on steel surfaces including prepration of new steel surfaces of any description over 10cm girth or width complete all as specified and as directed. |
| 79 | S&F framed work as in gate etc of angle,tubularor other section with gusset plates, braces etc complete drilled for fixing of steel sheeting or other covering prepared for hanging or sliding with and including either hooks & hinges for steel hanging door fitings complete all as specified and as directed. |
| 80 | Dismantling structural steel work including doors gates but excluding framed truss etccomplete all as specified and directed |
| 81 | M&L for making hole for exhaust fan at brick/stone wall area not exc 0.36 Sqm manually and making good as reqd shape for exhaust fan and repair by CM 1:3 complete all as specified and directed. |
| 82 | Demolition of cement concrete ( unreinforced) inroofs , floors (other than ground floors) beams, staircases,landing, chajjas and similar suspended work |
| 83 | M&L plain cement concrete 1:2:4 type B1 using 12.5 mm graded aggregate as in rooffor maint. the uniform slope etc any thickness at any height and in any position all as specified and directed by engr-in-charge at site. |
| 84 | M&LApplying evenly a coat of bituminous primer confirming to IS 3384 - 1986 @ 0.40 Kg/Sqm |
| 85 | M&L APPbased polymericmembrane minimum weight 3 Kg/Sqmand minimum 3 mm thick reinforced with polyster non wovefabric (wt not less than 150 gms/sqm) land on primed surface by forced application complete all as specified |
| 86 | Supply onlyliquidwater proofing compound ( For external new plaster surfaces) |
| 87 | Taking down old, unsv aluminium/copper point wiring (light, fan, socket or power) complete, incl fixture & fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc. removing materials to store for keeping in safe custody or for taking credit & making good the disturbed surfaces of walls, floors, etc. including Cost of making good the disturbed surfaces is deemed to be included in the unit quote rates, complete all as specified and directed by Engr-in-Charge. |
| 88 | Taking down old, unsv aluminium/copper point wiring (light, fan, socket or power) complete, incl fixture & fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc. removing materials to store for keeping in safe custody or for taking credit & making good the disturbed surfaces of walls, floors, etc. including Cost of making good the disturbed surfaces is deemed to be included in the unit quote rates, complete all as specified and directed by Engr-in-Charge. |
| 89 | Taking down old sub-main wiring incl fixture & fittings etc. removing materials to store for keeping in safe custody or for taking credit & making good the disturbed surfaces of walls, floors, etc., v complete all as specified and directed by Engr-in-Charge. |
| 90 | Disconnecting/dismantling of old existing un serviceable DB\"s along with metal enclosue concealed in walls of any type/way 240/415 Volts with their old/un serviceable burnt MCCB/MCB\"s etc.incl making good the disturbed surfaces and matching with existing surfces,including Cost of making good the disturbed surfaces is deemed to be included in the unit quote rates,complete all as specified and directed by Engr-in-Charge. |
| 91 | M & L for concealed point wiring with two single core 1.5 sqmm PVC insulated, unsheathed, FRLS cable, 1100 volts grade, ISI marked with multi stranded copper conductor drawn through and including non-metallic PVC rigid conduit (medium grade) with all fittings and accessories ISI marked incl provision of 1.5 sqmm PVC insulated, multistranded, unsheathed, copper conductor cable, FRLS, ISI marked as earth continuity conductor (green in colour) & incl fixing of modular metal flush boxes of appropriate size & thickness fixed flush to wall for mounting switch, sockets etc. with including cutting chases for conduits & sinkings for modular boxes & making good the disturbed surfaces, matching to the existing one etc., suitable for One Light/fan/Call Bell etc. point controlled by one switch 5/6 Amps, complete all as specified & as directedNOTE : 1) Modular metal flush boxes shall be measured & paid separately.2) Cutting chases & making good the disturbed surfaces is deemed to be included in the unit quoted rates.3)-The make/model of modular metal flush boxes & modular cover plates shall be same as that of modular switches & sockets. |
| 92 | All as item No. 91.00 here-in-above but suitable for One switch socket outlet point 5/6 Amps on Same board. |
| 93 | All as item No. 91.00 here-in-above but suitable for One switch socket outlet point 5/6 Amps on independent board. |
| 94 | All as item No. 91.00 here-in-above but suitable for with FRLS PVC insulatedcopper conductor cable of size 2.5 Sqmm and 2.5 Sqmm for earth continuity conductor green in colour for 16A switch socket complete. |
| 95 | M & L for concealed sub-main wiring alongwith earth wire of size (2 x 4.00) sq. mm + (1 x 4.00) sq. mm earth wire, ISI marked, FRLS, PVC insulated, multi stranded, copper conductor, single core cable drawn through and including non-metallic PVC conduit (medium grade) with all fittings and accessories ISI marked for conduits & sinkings for modular boxes & making good to walls, floors,ceiling etc. complete all as specified & as directed. |
| 96 | M & L for concealed sub-main wiring alongwith earth wire of size (2 x 6.00) sq. mm + (1 x 6.00) sq. mm earth wire, ISI marked, FRLS, PVC insulated, multi stranded, copper conductor, single core cable drawn through and including non-metallic PVC conduit (medium grade) with all fittings and accessories ISI marked for conduits & sinkings for modular boxes & making good to walls, floors,ceiling etc. complete all as specified & as directed. .NOTE for item No. 6 & 7 : 1) Two runs of PVC wire, one run of earth wire & one run of PVC rigid conduit (medium grade) will be measured as one length. 2) Modular metal flush boxes (if req) shall be measured & paid separately.2) Cutting chases & making good, includingnecessaryPutty work of the disturbed surfaces is deemed to be included in the unit quoted rates. |
| 97 | S & F Modular switch, one way, 6 Amp, 1 Module, 240 volt complete all as specified and as directed. |
| 98 | S & F Modular switch with indicator, one way, 16 Amp, 1 Module, 240 volt complete all as specified and as directed. |
| 99 | S & F Modular shuttered socket outlet 3 Pin, 6 Amp, 2 Module, 240 volts, ISI marked complete all as specified and as directed. |
| 100 | S & F Modular shuttered socket outlet 3 Pin, 6/16 Amp, 2 Module, 240 volts, ISI marked complete all as specified and as directed. |
| 101 | Supply & Fixingand concealing modular metal flush boxsuitable for fixing switches/sockets of 1/2 modules all as directed. |
| 102 | Supply & Fixingand concealing modular metal flush boxsuitable for fixing switches/sockets of 3 modules all as directed. |
| 103 | Supply & Fixingand concealing modular metal flush boxsuitable for fixing switches/sockets of6 modules all as directed. |
| 104 | Supply & Fixingmodular cover platesuitable for fixing switches/sockets of 1/2 modules all as directed. |
| 105 | Supply & Fixingmodular cover platesuitable for fixing switches/sockets of 3 modules all as directed. |
| 106 | Supply & Fixingmodular cover platesuitable for fixing switches/sockets of 6 modules all as directed. |
| 107 | S&F ceiling rose surface PVC/ Polycarbonate, Isolated body with face Bakelite three terminal complete all as specified and directed. Make: Havells/CG/Anchor |
| 108 | S&F IP>=20, Class I Wall mounted 4 feet LED batten with integrated electronic driver & Aluminium body complete with all accessories, prewired, including20 W with min 120 lumens/Watt output,6500 K, LED4 feettube light and connecting of flexible wire twin core from ceiling rose to fitting through & including flexible conduit from ceiling rose to fitting completeincl taking down old/unsv fittings all as specified and directed by Engr-in-Charge. |
| 109 | S&F IP >= 65,IK>=07, Class I Environment friendly, energy saving, surface mounted, decorative bulk head edge lit LED luminaire 10Wwith min 120 lumens/watt output made of pressure die cast aluminium housing with suitable fixing arrangement complete with all accessories internally prewired and including connecting up with and including twin core twisted flexible copper conductor cable of suitable size complete incl taking down old/unsv fittings all as specified and directed by Engr-in-Charge. |
| 110 | S&F IP >= 65, IK>=07, Class I energy saving and environment friendly long life high power LED as source of building security light of 30W with min 110 Lumens/Watts, made up of pressure die cast aluminum housing with acrylic cover as diffuser withincluding GI pipe bracket made out of 40mm dia light grade pipe of length 1.2 Mtrs, bend to shape 120-130 degree and MS clamps made out of 25x3mm flat iron 2 Nos including nut and bolts for fixing the bracket and making connections through & including flexible conduit from ceiling rose to fitting complete incl taking down old/unsv fittings all as specified and directed by Engr-in-Charge. |
| 111 | Supply, install, testing & commissioning of Exhaust fan, metal body with automatic back shutter louvers 300 mm sweep, 1400 RPM or more, Air Delivery not less than 1850 CMH, single phase, 240 Volts, AC, 50 Hz and connecting up complete including louvers and provision of cable 3/2 core of suitable size from ceiling rose to fan in flexible hose and making of suitable sized hole in the wall/existing window/ventillator etc. for fixing of the exhaust fan & making good the disturbed surfaces (if any) complete all as specified & as directed. Note :- (i) The cost of making hole in walls/other surfaces & making good the disturbed surfaces incl any framework/cement work/wood work/welding work etc. required for proper fixing of the exhaust fan & matching to the existing surface is deemed to be included in the unit quoted rates. |
| 112 | Supply and Fixing ceiling fans complete with blades, down rods of suitable lengh upto Ceiling/false ceiling level, with fan regulator 2Mand accessories, 230 V, 1200mm sweep, min air delivery 210 CFM with service value 6.00 BEE Five star rating with Brushless direct current rating (BLDC)including connecting up with and including twin/three core twisted flexible copper conductor cable of suitable size complete all as specified and directedby the Engr-in-Charge incl taking down old/unsv fan. Note : (i) Installed Ceiling fan\"s warranty card should be submitted to the Engr-in-Charge. (ii)The cost of making good the disturbed surfaces and matching to the existing/original surface is deemed to be included in the unit quoted rates (iii)The cost of taking down old unserviable Ceiling fan\"s andtranportation of old Ceiling fan\"s to be submittedto MES Store yardis deemed to be included in the quoted rate. |
| 113 | S & Fand concealing SPN DB, 12 Way, IP43, IK09, Metal double door type 240 volts fitted with busbar and blanking plates, neutral link and making good the disturbed surfaces with all other accessories including necessary connection all as specified and directed by Engr-in-Charge. |
| 114 | S & F and concealing SPN DB, 08 Way, IP43, IK09, Metal double door type 240 volts fitted with busbar and blanking plates, neutral link and making good the disturbed surfaces with all other accessories including necessary connection all as specified and directed by Engr-in-Charge. |
| 115 | S&F Miniature circuit Breakers, SPN,C-Series 240 Volts of capacity 6-32 Amps with breaking capacity 10 KA all as specified and dircted by Engr-in-Charge. |
| 116 | S&F Miniature circuit Breakers, single pole,C-Series 240 Volts of capacity (6-32 Amps) as ordered with breaking capacity 10 KA all as specified and dircted by Engr-in-Charge. |
| 117 | Supply, laying, jointing & testing XLPE insulated screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 sq mm 4.0 core in trenches / through GI pipe / fixed along with pole structure etc with all fixing & connecting accessories like Lugs, Gland etc incl taking down old existing Cable of any size/type complete all as specified & as directed. |
| 118 | Description all as per Item Sl No 117.00 here in above but of size 50 Sqmm 3.5 core. |
| 119 | Supply and laying light grade GI Pipe (ISI Marked) of 40mm dia for cable protection to be fixed on wall/in trenches with necessary clamps or in road crossing,complete all as directed(Rate qouted shall include MS clamps of required size wherever pipes are to be fixed on walls/other surfaces). |
| 120 | Supply and laying High density Poly-Ethylene Pipes(HDPE) of pressure rating 6Kgf/cm2 (ISI Marked) of 40mm dia for cable protection to be fixed on wall/in trenches/Ground with necessary clamps or in road crossing,complete all as directed(Rate qouted shall include MS clamps of required size wherever pipes are to be fixed on walls/other surfaces). |
| 121 | Excavation in trenches n.exc 1.5m wide and n.exc 1.5m in depth for taking out/laying of UG Cables, GI Pipe etc. and getting out in Soft/Loose soil complete. |
| 122 | Returning, filling in including spreading, levelling, watering and well ramming in layers n.exc 25cm thick. |
| 123 | Removing of excavated material n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point. |
| 124 | Supply and spreading Tibba Sand including watering and consolidation in trenches for cushioning/cable protection all as specified and directed by Engr-in-Charge. Note : Punned thickness shall be measured and paid |
| 125 | Supply and layingun-reinforced precast concrete cable cover, class LV, type 1, flat size 250 mm x 150 mm x 40 mmand abutting each other with gap between adjacent precast concrete cable cover not exceeding 10 mm over underground cables in trenches for cable protection of U/G cables with width equal to length of bricks complete all as specified and directed |
| 126 | M & L for cutting the existing hard standing /PCC /WBM road at a depth not less than 45 cm and 25 cm in width for passing of cable through GI pipe, returning filling in, complete including finishing the surfaces by providing top not less than 25 cm thick cement concrete type C-1 (1:3:6) using20 mm grade aggregate, bottom filled with excavated earth andfinishing to a uniform smooth surface complete all as specified and directed. |
| 127 | Supply, install, testing & commissioning of LT busbar junction box \"out-door type\" of size 600 mm (height) x 600 mm (breadth) x 300 mm (depth) (minimum dimensions), factory fabricated CPRI approved (type-tested) with suitable neoprene rubber gasket to make it completely dust & vermin proof & degree of protection not less than IP-55 & general construction confirming to IS-13947, double door, front & back openable. The box shall be provided with ventilation facility in the form of louvers for better heat dissipation & high grade Copper bus-bar of Size 300mm x 70mm x 6mm , min spacing of 75mm between the busbars & wrapped with coloured PVC tape /sleeves of rating in conformity to the Incoming cable rating. The panel board shall be fabricated out of 3.15 mm thick (for outer portions) & 2.00 mm thick (for inner portions) CRCA sheet duly pre-treated & powder coated, supporting angle iron frame & MC channel base suitable for 3 Phase, 4 wire system 415 /440 volts grade including I/C & O/G cable opening on bottom & at both sides including cable glands of suitable sizes with suitable PCC (1:3:6) type C-2 foundation , necessary earthwork (if any) incl Incoming MCCB of 63 Amps in seprate portion complete all as specified & as directed. |
| 128 | Supply, install, testing & commissioning of LT control panel board \"out-door type\" of size 1200 mm (height) x 1200 mm (breadth) x 350 mm (depth) (minimum dimensions), factory fabricated CPRI approved (type-tested) with suitable neoprene rubber gasket to make it completely dust & vermin proof & degree of protection not less than IP-55 & general construction confirming to IS-13947, double door, front & back openable. The panel shall be provided with ventilation facility in the form of louvers for better heat dissipation & high grade Copper bus-bar wrapped with coloured PVC tape /sleeves of rating in conformity to the Incoming ACB/MCCB rating. The panel board shall be fabricated out of 3.15 mm thick (for outer portions) & 2.00 mm thick (for inner portions) CRCA sheet duly pre-treated & powder coated, supporting angle iron frame & MC channel base suitable for 3 Phase, 4 wire system 415 /440 volts grade including complete internal wiring with not less than 2.5 Sqmm copper wire including cable glands and lugs of suitable sizes with suitable PCC (1:3:6) type C-2 foundation , necessary earthwork (if any)complete all as specified & as directed with & including the following accessories : |
| 129 | (i) BUS-BAR & INTERNAL CONNECTIONS :The bus-bars shall be made up of 04 Nos high grade Copper with rating should be suitable as per incoming Breaker, duly insulated with 1100 Volts grade standard colour coded PVC sleeves & rigidly mounted on suitable sized \"F\" class insulators of non-hygroscopic, non-combustible, all internal connections from main bus-bars to switch gears etc.PROVISION FOR CABLE ENTRY :The provision for cable entry /exit shall be provided in the bottom for both incoming & out-going cables with the help of glands matching the existing LT cable sizes.INCOMING :(a) MCCB 4 Pole (Ics = 100% Icu) with thermal magnetic release, adjustable short circuit & adjustable overload setting, suitable for isolation, having breaking capacity 25 KA & of rating 160-200 Amps - 01 . |
| 130 | OUTGOINGS :(a) MCCB 4 Pole (Ics = 100% Icu) with thermal magnetic release, adjustable short circuit & adjustable overload setting, suitable for isolation, having breaking capacity 25 KA & of rating 80 to 100 A - 01 No. (b) MCCB 4 Pole (Ics = 100% Icu) with thermal magnetic release, adjustable short circuit & adjustable overload setting, suitable for isolation, having breaking capacity 25 KA & of rating 63 to 80 A - 03 Nos. (c) Time switch 415Volts, 3 Phase of 20 Amps rating with Contactor complete .(d) MCB TPN \"C\" series having breaking capacity 10 KA of rating 06 to 32 Amps - 01 No.(e) MCB TPN \"C\" series having breaking capacity 10 KA of rating 40 to 63 Amps - 02 No. |
| 131 | INSTRUMENTATION SYSTEM :(a) Digital type Multi-Function meter with built in selector Switch & 03 Nos CTs matching with the I/C breaker, Accuracy Class - 1.0, 3 phase, Size 96 x 96 mm.Make : L & T, Cat No: WL411010OOOO or techno-commercially equivalent of Elmeasure /Secure.(b) Indicator lamp with integral circuit (230/240 Volts) & cluster LED (Red, Orange, Blue) - 01 Set.(c) Danger notice plate of size 20 x 15 cm of 1.6mm thick mild-steel sheet, vitreous enamelled white, with letters, figures and conventional skull and bones in signal-red colour and fixed with MS clamps, bolts and nuts of approved size, for LT conforming to IS-2551 - 02 Nos (Front & Back).(d) Door opening key - 02 Nos |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2025 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
