|
| 1 | Page No- 10, Item No- 2b, Dismantling all types of plain cement concreteworks, stacking serviceable materials at site and removing rubbish as directed within a lead of 75m. In ground floor including roof.(a) upto 150 mm. thick |
| 2 | Page No; 12. Item No; 13, Removal of rubbish,earth etc. from the workingsite and disposal of the same beyond thecompound, in conformity with the Municipal Corporation Rules for such disposal, loading into truck and cleaning the site in all respect as per direction of Engineer in charge |
| 3 | Page No; 192. Item No; 1, Labour for Chipping of concrete surface before taking up Plastering work. |
| 4 | Page No; 15; Item No; 7(a)(b), Brick work with 1st class bricks in cement mortar (1:4)(a) In foundation and plinth |
| 5 | Page No; 32; Item No; 29, 125mm thick brickwork with 1st class bricks in cement mortar (4:1) In ground floor. |
| 6 | Page No; 189; Item No; 1(ii)(b), Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed andraking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excludingcost of chipping over concrete surface](i) With 1:4 cement mortar.(c) 15 mm thick plaster |
| 7 | Page No; 192; Item No; 15, Neat cement punning about 1.5mm thick in wall, dado, window sill, floor etc. NOTE:Cement 0.152 cu.m per100 sq.m. |
| 8 | Page No; 26; Item No; 10(i), Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in groundfloor as per relevant IS codes.(i) Pakur Variety |
| 9 | Page No; 101; Item No;2A(i)(b), M.S. structural works with hollow sections ( square or rectangular shape) conforming to IS: 806-1957 & IS:1161-1958) connected to one another with bracket, gusset, cleat as per design, drawing & direction of Engineer-in-Charge complete including cutting to requisite shape & size, fabrication including metal arc welding conforming to IS: 816-1956 & IS: 9595 using electrodes of approved make and brand conforming to IS:814- 1957, haulage, hoisting and erection all complete. The rate includes the cost of all M.S. Hollow section, all consumables such as electrodes, gas and hire charges of all tools and plants and labour reqired for execution and all incidental chages (such as electricity, labour insurance) etc. complete. Payment to be made on the basis of calculated weight of structural memebrs of MS Holow Section as specified in relevent IS code in finished work. Payment for gusset, bracket, cleat may be made by adding the actual weight of such items with weight of finished structural members. The rates are considered for a hight of erection 8 m. / 2nd floor level from the ground. Add 1.5 % extra over the rate for eachadditional floor or 4m. beyond the initial 8 m. or part thereof. i) For roof truss worksb) Span beyond 12 Mtr and up to 20.00 Mtr |
| 10 | Page No; 26; Item No; 10(i), Welding in M.S. structural work with gas or electric: (a) Tack weld |
| 11 | Page No; 82; Item No; 14(i)(a), Supplying , fitting & fixing Zn-Al alloy (55% Al & 45% Zn) coating of 150 grams per sq. metre (followed by colour coated on both side) steel sheet work having minimum yield strength of 550 Mpa of trapizoidal profile of approved make (excluding the supporting frame work) fitted and fixed with 55 mm & 25 mm self tapping screw, EPDM Washer 16 mm dia & 3 mm th. washer etc. complete with 150 mm end lap and one corrugation minimum side lap. (Payment to be made on area of finished work). (i) In Roof:-a) With 0.5 mm thick sheet |
| 12 | Page No; 212; Item No; 21, Supplying, fitting & fixing UPVC pipes A- Type and fittings conforming to IS:13592-1992 with all necessary clamps nails, including making holes in walls, floor etc. cutting trenches in any soil through masonry concretestructures etc if necessary and mending good damages including joining with jointing materails (Spun Yarn, Valamoid/Bitumen/M-Seal etc) complete. A) UPVC Pipes:(iii) 160 mm. Dia. |
| 13 | B) UPVC Fittings:c) Bend 87.5 degree (iii) 160 mm. Dia. |
| 14 | Page No; 114; Item No; 1(f), Wood work in door and window frame fitted and fixed inposition complete including a protective coat of painting at the contact surface of the frame exluding cost of concrete, Iron Butt Hinges and M.S clamps. (The quantum should be correted upto three decimals).(f) Sishu, Gamar, Champ, Badam, Bhola, Mogra, Hallak |
| 15 | Page No; 117; Item No; 1, Panel shutters of door and window, as per design (each panel consisting of single plank without joint), including fitting and fixing the same in position but excluding the cost of hinge andother fittings. In first floor.(iii) 35mm thick shutters with 19mm thick panel of size 30to 45 cm.(b) Sishu, Gamar, Champ, Badam, Bhola, Mogra, Hallak. |
| 16 | Page No; 140; Item No; 4, Supplying, fitting and fixing M.S. clamps for door andwindow frame made of flat bent bar, end bifurcated with necessary screws etc. by cement concrete(1:2:4) as per direction. (Cost of concrete will be paid separately)(a) 40mm X 6mm, 250mm Length |
| 17 | Page No; 140; Item No; 5, Iron butt hinges of approved quality fitted and fixed with steelscrews, with ISI mark.(viii) 100mm. X 75mm. X 3.50mm. |
| 18 | Page No; 140; Item No; 7, Iron socket bolt of approved quality fitted and fixed complete.(d) 225mm long x 10mm dia bolt. |
| 19 | Page No; 140; Item No; 7, Iron catch hook of approved quality fitted and fixed to shutterand chowkat.(b) 6mm dia x 225mm long. |
| 20 | Page No; 200; Item No; 1, (a) Priming one coat on timber or plastered surface with synthetic oil bound primer of approved quality including smoothening surfaces bysand papering etc.Wood work |
| 21 | Page No; 200; Item No; 1, (b) Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces bysand papering etc. |
| 22 | Page No; 200; Item No; 2, (A) Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc.including using of approved putty etc. on the surface, if necessary :(a) On timber or plastered surface : With super gloss (hi-gloss) -(iv) Two coats (with any shade except white) |
| 23 | (b) On steel or other metal surface :With super gloss (hi-gloss) -(iv) Two coats (with any shade except white) |
| 24 | Add 9% SGST |
| 25 | Add 9% CGST |
| 26 | Add @ 1% loabour welfire cess over (BLD SCH.). Please Enable Macros to View BoQ information |
