Name of Work:- Renovation Of Store Room At Bankola Area Hospital Under Bankola Area. (Retender) Nit संख्या.: Ecl/Gm/Ba/E-Tender/25-26/Civil/69 (02) दिनांक: 05.12.2025
Sl. No.
Item Description
1
Grading roof for water proofing treatment with Cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 20 mm nominal size)
2
Brick work with common burnt clay F.P.S. bricks of class designation 7.5 In superstructure above plinth level up to floor V level in all shapes and sizes in: Cement mortar 1:6 (1 cement: 6 coarse sand)
3
CEMENT PLASTER (IN FINE SAND) 12mm thick cement plaster of mix 1:6 (1 cement: 6 fine sand)
4
6mm thick cement plaster in ceiling 1:3 (1 cement: 3 fine sand)
5
Providing & fixing wall tiles
6
Providing and applying putty
7
Distempering with oil bound Distemper
8
Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer-Using flats 30x6mm for diagonal braces and central cross piece
9
Painting on G.S. sheet with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade-New work (two or more coats) including a coat of approved steel primer but excluding a coat of mordant solution
10
Painting with synthetic enamel paint:old work
11
Renewing glass panes, with putty and nails wherever necessary including racking out the old putty: Float glass panes of thickness 4 mm
12
P/F factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance ±1mm), with wall thickness 2.0 mm (±0.2 mm), corners of the door frame to be Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.5. tube of size 19 X 19 mm and 1mm (t 0.1 mm) wall thickness and 3 nos, stainless steel hinges fixed to the frame complete as per manufacturer\"s specification and direction of Engineerin-charge: Extruded section profile size 48x40 mm
13
P/F to existing door frames-24 mm thick factory made PVC door shutters made of styles and rails of a uPVC hollow section of size 59x24 mm and wall thickness 2 mm with inbuilt edging on both sides. The styles and rails mitred and joint at the corners by means of M.S. galvanised/plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 20x20 mm and 1 mm wall thickness. The lock rail made up of \"H\" section, a uPVC hollow section of size 100x24 mm and 2 mm wall thickness, fixed to the shutter styles by means of plastic/galvanised M.S. \"U\" cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer\"s specification and direction of Engineer-in-charge. (For W.C. and bathroom door shutter).
14
Total impact of GST for the purpose of CTC Please Enable Macros to View BoQ information
We takes all possible care for accurate & authentic tender information, however Users
are requested to refer Original source of Tender Notice / Tender Document published by
Tender Issuing Agency before taking any call regarding this tender.
