|
| 1 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 2 | Reinforced cement concrete work in beams, suspended floors, roofshaving slope up to 15° landings, balconies, shelves, chajjas, lintels,bands, plain window sills, staircases and spiral stair cases above plinthlevel up to floor five level, excluding the cost ofcentering, shuttering,finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarsesand(zone-III) derived from natural sources : 3 graded stone aggregate20 mm nominal size derived from natural sources). |
| 3 | Centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platform |
| 4 | Centering and shuttering including strutting, propping etc. and removalof form forLintels, beams, plinth beams, girders,bressumers andcantilevers |
| 5 | Steel reinforcement for R.C.C. work including straightening,cutting,bending, placing in position and binding all complete above plinth level. |
| 6 | Brick work with non modular fly ash bricks conforming to IS:12894, class designation 7.5 average compressive strength in super structure above plinth level up to floor V level in :Cement mortar 1:6 (1 cement : 6 Coarse sand |
| 7 | Half brick masonry with non modular fly ash bricks of class designation 7.50, conformingio IS :12894, in super structure above plinth and upto floor V level. Cement mortar 1 : 4 (1 cement : 4 coarse sand) |
| 8 | Providing and fixing 16 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels. Granite stone slab of colour Lakha Red. Area of slab over 0.50 sqm |
| 9 | Providing and fixing 16 mm thick gang saw cut mirror polished premoulded and prepolished) machine cut for kitchen platforms, vanity countersand similar locations of required size of approved shade, colour and textureincluding rubbing,moulding and polishing to edge to give high gloss finish etc. complete at all levels. Granite stone slab ofLakha Red,Area of slab over0.5 sqm |
| 10 | Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete. |
| 11 | Providing and fixing aluminium extruded section body tubular typeuniversal hydraulic door closer (having brand logo with ISi, IS : 3564,embossed on the body, door weight upto 36 kg to 80 kg and door widthrom 701 mm to 1000 mm), with double speed adjustment with necessaryaccessories and screws etc. complete. |
| 12 | Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 300x16 mm |
| 13 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 150x10 mm |
| 14 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 125 mm |
| 15 | Providing and fixing aluminium hanging floor door stopper, ISI marked,anodised (anodic coating not less than grade AC 10 as per IS : 1868)transparent or dyed to required colour and shade, with necessary screwsetc. complete.Twin rubber stopper |
| 16 | Providing and fixing bright finished 100 mm mortice lock with 6 leverswithout pair of handles of approved quality for aluminium door, withnecessary screws etc complete as per direction of Engineer- in-charge |
| 17 | Providing and fixing factory made uPVC glazed/wire mesh windows/doors comprising of leadfree uPVC multi-chambered frame, sash and mullion/coupler (where everrequired)extrudedprofileshaving minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape,colouranddesignduly reinforced with galvanized mild steel section made of required shape & size as perCPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor(whereever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fastenersof minimum 8 mm dia with countersunk head, comprisingof matching polyamide PA6 gradesleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plasticcaps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required)shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, includingdrilling of holes for fixing hardware and drainage of water etc. After fixing frame the gapbetween frame and adjacent finished wall shall be filled with weather proof silicon sealant overbacker rod of approved size and quality, all complete as per approved drawing conformingto CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcementand cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge. Wire mesh / Glazing of plain/ toughened/ laminated/ double glass unit with / without highperformance coatings as per design requirements and conforming to IS: 3548 & IS: 16231shall be paid separately.Note:Structural design proof checked from a Government Engineering Institute, to be providedby the manufacturer for : (i) Sites with basic wind speed > 45 m/sec as per IS 875 – Part 3(ii) Sites with structure height more than 20m for all wind speeds.Casement door double panel with French (False) Mullion with zinc alloy (zamak) 3D hinges,multi-point locking system with cylinder, zinc alloy (zamak) powder coated handles on bothsides. Using R3 series with frame (55 mm & above) x (50mm & above) & sash (55 mm & above) x(85mm & above) & French (False) mullion (55 mm & above) x (60mm & above). (Height upto2.5 metre). |
| 18 | Providing and fixing stainless steel soft closing heavy typetelescopic drawer channels of approved make 500 mm long withscrews etc. complete as per directions of Engineer- in-charge |
| 19 | Providing & fixing fly proof wire gauze to windows, clerestory windows &doors with M.S. Flat 15x3 mm and nuts & bolts complete.Stainless steel (grade 304) wire gauze of 0.5 mm dia wireand 1.4 mm aperture on both sides |
| 20 | Providing and fixing 10 mm thick acid and/or alkali resistant tiles ofapproved make and colour using acid and/or alkali resisting mortarbedding, and joints filled with acid and/or alkali resisting cement as perIS : 4457, complete as per the direction of Engineer-in- Charge.In dado/skirting on 12 mm thick mortar 1:4 (1 acid proofcement : 4 coarse sand)Acid and alkali resistant tile sqm |
| 21 | Providing and laying Vitrified tiles in floor in different sizes(thickness to be specified by the manufacturer) with waterabsorption less than 0.08% and conforming to IS:15622, ofapproved brand & manufacturer, in all colours and shade, laidon 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand)jointing with grey cement slurry @3.3 kg/sqm including groutingthe joints with white cement and matching pigments etc. Thetiles must be cut with the zero chipping diamond cutter only .Laying of tiles will be done with the notch trowel, plier, wedge,clips of required thickness, leveling system and rubber mallet forplacing the tiles gently and easily.Double charge vitrified tile polished finish of size. Size of Tile 600 x 600 mm |
| 22 | Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer)with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting thejoints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Double charge vitrified tile polished finish of sizeSize of Tile 600 x 1200 mm |
| 23 | Grouting the joints of flooring tiles having joints of 3 mm width, usingepoxy grout mix of 0.70 kg of organic coated filler of desired shade(0.10 kg of hardener and 0.20 kg of resin per kg), including filling /grouting and finishing complete as per direction of Engineer-in-charge.Size of Tile 600x600 mm |
| 24 | Grouting the joints of flooring tiles having joints of 3 mm width, usingepoxy grout mix of 0.70 kg of organic coated filler of desired shade(0.10 kg of hardener and 0.20 kg of resin per kg), including filling /grouting and finishing complete as per direction of Engineer-in-charge. Size of Tile 600x 1200 mm |
| 25 | Deduct for not grouting the joints with white cement and matchingpigment in the items of fixing of vitrified tiles. (Minus Item) |
| 26 | Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2coarse sand : 4 stone aggregate 10 mm and down gauge), includingfinishing with cement mortar 1:3 (1 cement : 3 fine sand) as perstandard design :In 75x75 mm deep chase |
| 27 | Providing and fixing on wall face unplasticised Rigid PVC rain waterpipes conforming to IS : 13592 Type A, including jointing with sealring conforming to IS : 5382, leaving 10 mm gap for thermal expansion,(i) Single socketed pipes.75 mm diameter |
| 28 | Providing and fixing on wall face unplasticised - PVC moulded fittings /accessories for unplasticised Rigid PVC rain water pipes conformingtoIS : 13592 Type A, including jointing with seal ring conforming toIS : 5382, leaving 10 mm gap for thermal expansion Single tee without door 75x75x75 mm |
| 29 | Providing and Fixing 15 mm thick densified tegular edged eco friendlylight weight calcium silicate false ceiling tiles of approved texture ofsize 595 x 595 mm in true horizontal level, suspended on interlocking metal grid of hot dipped galvanised steel sections (galvanising@ 120 grams per sqm including both side) consisting of main ‘T’runner suitably spaced at joints to get required length and of size24x38 mm made from 0.33 mm thick (minimum) sheet, spaced1200 mm centre to centre, and cross “T” of size 24x28 mm madeout of 0.33 mm (Minimum) sheet, 1200 mm long spaced betweenmain’T’ at 600 mm centre to centre to form a grid of 1200x600 mmand secondary cross ‘T’ of length 600 mm and size 24 x28 mmmade of 0.33 mm thick (Minimum) sheet to be inter locked at middleof the 1200x 600 mm panel to from grid of size 600x600 mm, restingon periphery walls /partitions on a Perimeter wall angle pre-coatedsteel of size(24x24X3000 mm made of 0.40 mm thick (minimum)sheet with the help of rawl plugs at 450 mm centre to centre with 25mm long dry wall screws @ 230 mm interval and laying 15 mmthick densified edges calicum silicate ceiling tiles of approved texturein the grid, including, cutting/ making opening for services likediffusers, grills, light fittings, fixtures, smoke detectors etc., whereverrequired. Main ‘T’ runners to be suspended from ceiling using G.I.slotted cleats of size 25x35x1.6 mm fixed to ceiling with 12.5 mmdia and 50 mm long dash fasteners, 4 mm G.I. adjustable rods withgalvanised steel level clips of size 85 x 30 x 0.8 mm, spaced at1200 mm centre to centre along main ‘T’, bottom exposed with 24mm of all Tsections shall be pre-painted with polyster baked paint,for all heights, as per specifications, drawings and as directed byEngineer-in-Charge. Note :- Only calcium silicate false ceiling area will be measuredfrom wall to wall. No deduction shall be made for exposedframes/opening (cut outs) having area less than 0.30 sqm.Thecalcium silicate ceiling tile shall have NRC value of 0.50(Minimum), light reflection > 85%, non- combustible as per B.S.476 part IV, 100% humidity resistance and also having thermalconductivity <0.043 w/mK. |
| 30 | 12 mm cement plaster of mix :1:6 (1 cement: 6 fine sand) |
| 31 | 12 mm cement plaster of mix : 1:4 (1 cement: 4 coarse sand) (Store & Purchase) |
| 32 | 6 mm cement plaster of mix1:3 (1 cement : 3 fine sand) |
| 33 | Distempering with oil bound washable distemper of make \"\" Asian UNO\"\"to give an even shade :New work (two or more coats) over and including water thinnable priming coat with cement primer of make \"\"Asian paint Smart Care \"\".(Agency shall bring container at a time and make signatureofA E E(Civil ) before start of the work and keep the signed container till the final bill is passed) |
| 34 | Finishing walls with Acrylic Smooth exterior paint of required shade of Asian make APEX :New work (Two or more coat applied @ 1.67 ltr/10 sqmover and including priming coat of exterior primer applied of makeAsian smartcare damp proof ( applied@ 2.20 kg/10 sqm) |
| 35 | Finishing walls with ready mixed Premium acrylic emulsion paintof make Asian Apcolite premiumas per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives.New work (Two or more coats applied @ 1.43 litre/ 10sqm. Over and including priming coat of exterior primer of make Asiansmartcare applied @ 0.90 litre/10 sqm. (Store & Purchase) |
| 36 | Painting with synthetic enamel paint of make \"\"Asian Apcoliteandmanufacture of required colour to give an even shade :Two or more coats on new work over an under coat ofsuitable shade with ordinary paint of make \"\"Asian Smart care\"\" andmanufacture |
| 37 | Providing and applying white cement based putty of average thickness1 mm, of approved brand and manufacturer, over the plastered wallsurface to prepare the surface even and smooth complete. |
| 38 | Painting with synthetic enamel paint ofmake \"\"Asian Apcolite\" of required colour to give an even shade :One or more coats on old work |
| 39 | Hacking of CC flooring including cleaning for surface etc. complete as per direction of the Engineer-in-Charge. (Store & Purchase) |
| 40 | Demolishing cement concrete manually/ by mechanical meansincluding disposal of material within 50 metres lead as per directionof Engineer - in - charge.Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) |
| 41 | Demolishing brick work manually/ by mechanical means includingstacking of serviceable material and disposal of unserviceable materialwithin 50 metres lead as per direction of Engineer-in-charge.In cement mortar cum |
| 42 | Dismantling doors, windows and clerestory windows (steel or wood)shutter including chowkhats, architrave, holdfasts etc. complete andstacking within 50 metres lead : Of area 3 sq. metres and below |
| 43 | Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead : of area beyond 3 sq. metres |
| 44 | Dismantling tile work in floors and roofs laid in cement mortar includingstacking material within 50 metres lead.For thickness of tiles above 25 mm and up to 40 mm |
| 45 | Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. |
| 46 | Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved dumping ground or as approved by Engineer-in-charge for all leads including all lifts involved |
| 47 | Providing and fixing white vitreous china laboratory sink with C.I. brackets, , 40 mm C.P brass waste and 40mm C.P. brass trap with necessary C.P. brass unions complete, including painting of fittings and brackets, cutting and making good the wall wherever required : Size 600x450x200 mm |
| 48 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible pipe 32 mm dia |
| 49 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.Internal work - Exposed on wall 20 mm nominal outer dia SDR-11 Pipes |
| 50 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.Internal work - Exposed on wall 40 mm nominal outer dia SDR-11 Pipes |
| 51 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 20 mm nominal bore |
| 52 | Providing and fixing aluminium work for doors, windows, ventilatorsand partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved makeconforming to IS: 733 and IS: 1285, fixing with dash fasteners ofrequired dia and size, including necessary filling up the gaps atjunctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free,straight, mitred and jointed mechanically wherever required includingcleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, panelingand dash fasteners to be paid for separately) :Powder coated aluminium (minimumthickness of powder coating 50 micron) For fixed portion |
| 53 | Providing and fixing aluminium work for doors, windows, ventilatorsand partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved makeconforming to IS: 733 and IS: 1285, fixing with dash fasteners ofrequired dia and size, including necessary filling up the gaps atjunctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free,straight, mitred and jointed mechanically wherever required includingcleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, panelingand dash fasteners to be paid for separately) :Powder coated aluminium (minimumthickness of powder coating 50 micron For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) |
| 54 | Providing and fixing glazing in aluminium door, window, ventilatorshutters and partitions etc. with EPDM rubber / neoprene gasketetc. complete as per the architectural drawings and the directions ofengineer-in-charge . (Cost of aluminium snap beading shall be paidin basic item): With float glass panes of 5 mm thickness (weight notless than 12.50 kg/sqm) |
| 55 | Dismantling, cutting and refixing the existing wooden sinngle/ doule feaf doorshutter in good condition incuding fixing necessary screws as required as per direction of Engineer-in-charge. |
| 56 | Providing and fixing 8 mm thick plain multipurpose cement board fixed in aluminium doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. |
| 57 | P/F 75mm aluminumstar locking handleof TPI make or equivalent for aluminum sliding window and cup-board shutter of approved quality as directed by the EIC. |
| 58 | Providing and fixing hard plastic roller of TPI make or equivalent for sliding Aluminium window/cup-board shutter including all fittings of approved quality as directed by the EIC. |
| 59 | Providing and fixing C.P. brass swan neck three way tap ( Heavy type ) of approved quality as directed by the EIC.15 mm nominal bore. |
| 60 | Providing and fixingroller blind (Black out) without head rail ofVISTA make model SERENE (OPAQUE)without head rail ofapproved colour as per the direction of the EIC. |
| 61 | Providing and laying 15 mm thick Johnson make Endura Max grip tiles in floor in different sizes (thickness to be specified by the manufacturer)with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting thejoints with white cement and matching pigments etc.Size of Tile600 x 600 mm |
