|
| 1 | Dismantling of asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings), complete all as specified and directed. |
| 2 | S&F pre-painted colored trapezoidal profiled Galvalume/Zincalume sheet with min 0.50mm TCT confirming to IS-513 (AZ-150 GSM, AL Zn alloy metalic coating, 550 MPA yield stress as per AS-1397), colour /exterior coat of silicon modified polyster/ BHP X RW paint system 20 microntop coat applied over 5 micron primer and a 5 micron polyster back coat applied over 5 micron primer, as in roof covering/ cladding to wall, fixed with and including Galvanised self drilling self-tapping fastener (12-14 x 55 with EPDM seals), complete all as specified and directed. |
| 3 | S&F pre-painted colored plain sheet profiled Galvalume/Zincalume sheet with min 0.50mm TCT confirming to IS-513 (AZ-150 GSM, AL Zn alloy metalic coating, 550 MPA yield stress as per AS-1397),colour /exterior coat of silicon modified polyster/ BHP X RW paint system 20 microntop coat applied over 5 micron primer and a 5 micron polyster back coat applied over 5 micron primer,as in roof covering/ cladding to wall fixed with and including Galvanised self drilling self-tapping fastener (12-14 x 55 with EPDM seals), complete all as specified and directed. |
| 4 | Dismantling wrought iron as in rafters, purlins, truss etc and/or mild steel work of any description not otherwise provided for, complete all as specified and as directed. |
| 5 | Dismantling timber scantlings ( framed works) 40 sq. cm and over in section, in any position, complete all as specified and as directed. |
| 6 | S&F mild steel tubular trusses including special shaped washer etccomplete using ERW on indication bolt welded table conforming to IS 116 to 1979 grade ST-240 all as specified and as directed. |
| 7 | S&F mild steel rolled sections [Fe 410-W (Gde E-250) quality - A] as in roof trusses (framed), trussed, main and cross beams, hip and jack rafters, purlins, Gusset plate and base plates, where connected to common rafters and running rails, distance pieces, cleats, guides for sliding doors; fixed with angle cleats or other connecting plates, framing for cladding, staging for water tanks, nuts, bolts, washers etc,includng welding or riveting etc, complete all as specified and as directed. |
| 8 | S&F anodised aluminium snap grid of size 605x605mm frame work for false ceiling hangers 6mm dia GI (upto 1200mm length) adusting level fixed to roof slabs by means of ceiling cleats made out GIflat iron 40x3mm size 60mm long and fixed expansion hold fasteneners 12.5mm dia and 40mm long, including dismantlingof wall and ceiling boardscomplete all as specified and as directed. |
| 9 | S & F 4mm thick Non-asbestos fibre cement decorative/designer building boards to steel frame work with screws in ceiling (flat and/or slopping) and including jointless finish with & also including joining compound and tape as per manufacturer instructions, including dismantlingof wall and ceiling boardscomplete all as specified and as directed.Notes :- (i)The board shall be confirming to IS-14862 and shall be manufactured from the homogeneious mixture of cement, quartz and cellulose and shall be curred with high pressure steam using auto claving process.(ii) Aluminium frame work shall be measured and paid for separately. |
| 10 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), including disposing off the retrieved debris outside the premises, complete all as specified and as directed. |
| 11 | M & L for PCC type B-1 (1:2:4) (20mm graded aggregats) 25mm thick in flooring finishing cement concrete surface even and fair to recive tiles etc complete all as specified and as directed. |
| 12 | M& L for coloured Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) of approved size, area of eachtile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed inwhite cement mixed with pigments to match with the shade of tiles, over and including 15mm thick screed bed in CM (1:6), complete all as specified and as directed. |
| 13 | all as per above item no 12 here-in-before but in vertical surface such as skirting / dado etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match with the shade of the tiles, over and including 10mm thick cement mortal backing coat in CM (1:3), complete all as specified andand as directed. |
| 14 | M& L for coloured Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) of approved size, area of eachtile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed inwhite cement mixed with pigments to match with the shade of tiles, over and including 15mm thick screed bed in CM (1:6), complete all as specified and as directed. |
| 15 | M&L for coloured Glazed ceramic tiles of size 300mmx 450mm , 6 to 7 mm thick on the vertical surfaces such as in skirting / dado etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match with the shade of the tiles, over and including 10mm thick cement mortal backing coat in CM (1:3), complete all as specified andand as directed. |
| 16 | Dismantling Stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any morter complete all as specified and as directed. |
| 17 | M&L for granite (of any type)15mm thick (Table rubbled andmirror polished ) insteps, jambs, pillars, window-cills, cooking platform etc, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing including 20mm thick screed bed in CM (1:4), including necessary dismantling of floor tiles complete all as specified and directed. |
| 18 | M&L for 20 to 25mm thick Machine cut kota stone slabsas in flooring, laid over and including 20mm thick screed in cm (1:6), set, jointed and pointed in neat cement slurry mixed with pigment to match with the shade of the slabs, including rubbing and mirror polishing etc, complete all as specified and as directed. |
| 19 | M&L for 20 to 25mm thick Machine cut kota stone slabsas in riser of step, skirting, dado etc. laid over and including 10mm thick backing layerin cm (1:4), set, jointed and pointed in neat cement slurry mixed with pigment to match with the shade of the slabs, including rubbing and mirror polishing etc, complete all as specified and as directed . |
| 20 | Demolition of brick work or rubbled stone masonry including all quoins, arches , pillars etc built in cement mortar including disposing off the retrieved debris outside the premises, complete all as specified and as directed. |
| 21 | M&L forBrickwork with fly ash Bricks(old size), straight or curved on plan to any radius in half brick walls built in Cement morter (1:4), complete all as specified and directed |
| 22 | M&L forBrickwork with fly as Bricks(old size), straight or curved on plan exc 6m mean radius built in Cement morter (1:6), complete all as specified and directed |
| 23 | Taking down cement plaster on brick or concrete surfaces etc,including raking out joints, hacking for key, scrubbing down with water etc, and also including removal of rubbish off the premises, complete all as specified and directed. |
| 24 | M&L for rendering 15 mm thick in cement mortar (1:6), on brick work or concrete surfaces, finished even and smooth without using extra cement, complete all as specified and directed. |
| 25 | M&L for rendering 15 mm thick in CM (1:4) on brick work or concrete surfaces finsihed even and smooth (without using extra cement) mixed with water proofing compound as per manufacturer instructions, complete all as specified and as directed.Note:- WPC shall be measured and paid seperately. |
| 26 | Supply only integral water proofing compound, complete all as specified and as directed. |
| 27 | M&L forcomplete removal of existing treatement and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/ litre and UV resistance as per IS 15489:2004, Alkali & fungal resistane, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm on old surfaces. complete all as specified |
| 28 | Material & Labour for preparation of new plastered surface of walls andapplying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces. |
| 29 | M&L for preparing new plastered surface of walls and applying two coat of oil bond distemper, white or any tint, over a coat of primer over1 mm thick wall care Putty etc complete as specified and directed. |
| 30 | M&L forFramed work as in doors or gates or other section with gusset plates, rails, braces, etc complete drilled for fixing of steel sheeting or other covering Doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings( exclusive of steel sheeting or other covering , running rails and guides) and hanging , also fastening and fixing confirming to FE-410 Gde E-250 quality Acomplete all as specified and as directed |
| 31 | M&L for 1mm thick plain , black , mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) complete all as specified and as directed |
| 32 | M&L for complete removal of existing treatement of internal wall and appying two coat of oil bound distemper over 1 mm thick wall care putty including a coat of alkali resistant priming paintetc complete all as specified and as directed |
| 33 | M&L preparation of new steel surfacesof any description not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paintover a coat of red oxide complete all as specified and as directed. |
| 34 | M&L preparation of old painted surfaces of steel surfacesof any description not otherwise described over 10 cm width or girth and applying One coat of synthetic enamel paintcomplete all as specified and as directed. |
| 35 | M&L for preparing new wooden surfaces of any description not otherwise described, over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and directed . |
| 36 | M&L for preparing old wooden surfacesnot otherwise described, over 10 cm in width or girth and applying one coats of synthetic enamel paintcomplete all as specified and directed . |
| 37 | M&L for Chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed with neat cement slurry in floorsand pointed with pigment to match the shade, including 15 mm thick screed bed in CM 1:6. Complete all as specified and directed. |
| 38 | Demolition of cement concrete (un-reinforced )in ground floors and pavings n exc 15 cm thickness (below or above ground level)including disposing off the retrieved debris outside the premises, complete all as specified and as directed. |
| 39 | M&L for 75mm thick pcc type C-2, 1:3:6 (using 40 mm graded aggregrate) as in sub base of floor finishing cement concrete surface even and fair Without using extra cement. Complete all as specified and directed. |
| 40 | M&L for providing 75mm thick PCC (1:3:6) type C2 (using 20mm graded crushed stone aggregate), as in plinth protection, surface finished even & smooth without using extra cement including provision of 10 mm joints (at an interval of 3 metre and turnings) duly filled with fine sand and bitumen in the ratio of (3:1), complete all as specified and directed. |
| 41 | M & l for Making good under cills over arches, lintel and bresummers,including all pinning when nessesary with using cement mortar 1:6 complete all as specified |
| 42 | Providing and laying 60 mm thick factorymade chamfered edge cement concrete paverblock of M-35 grade with approved colour,design & pattern as in footparth, parks,lawns, drive ways or light traffic parking etc.,of required strength, thickness & size/shape, made by table vibratory method usingPU mould, laid in required colour & patternover and including 50mm thick compactedbed of fine sand, compacting and properembedding/ laying of inter locking paverblocks into the sand bedding layerthroughvibratory compaction by using platevibrator, fillingthe joints with sand andcutting of paver blocks as per required sizeand pattern, finishing and sweeping extra complete all as specified |
| 43 | M&L for cement concrete (1:3:6) type C-1 (using 20mm graded crushed stone aggregates) as in hold-fast blocks, blocks for fixing lugs, fillingof pressed steel chowkhat, copingand the like including necessary form work, complete all as specified and as directed. |
| 44 | Taking down chowkats or frames with Wooden/PVC/Flush shutters (without taking off shutter from frames) not exc. 1.5 sqm each, including cutting holes for removing the hold fast etc,disposing off the retrieved debris outsite the premises, complete all as specified and as directed. |
| 45 | Taking down chowkats or frames with Wooden/PVC/Flush shutters (without taking off shutter from frames) exc. 1.5 Sqm but n exc 4 Sqm each, including cutting holes for removing the hold fast etc,disposing off the debris outsite the premises, complete all as specified and as directed. |
| 46 | S&F factory made 1.25 mm thick pressed steel frame of size 165 X 60 mm for doors with one or more rebates including necessary provision of lugs, locks strike plate, hinges etc, applying one shop coat of Zinc Chromate primer after prepation of the surfaces,complete all as specified and as directed. |
| 47 | S&F factory made 1.25 mm thick pressed steel frame of size 105 X 60 mm for doors with one or more rebates including necessary provision of lugs, locks strike plate, hinges etc, applying one shop coat of Zinc Chromate primer after prepation of the surfaces,complete all as specified and as directed. |
| 48 | S&FFactory made 35mm thick flush shutter solid core construction, with block board core and plywood face panels, commercial type on both sides, complete all as specified and as directed. |
| 49 | M&L for 2nd class hard wood (Hollock/Kalasiris/Brjsal/Gamari) (kiln seasoned and chemically pressure treated) 35 mm thick glazed and skeleton shutters,open rebated and prepared to rceieve glass, gauze, etc, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass,etc, sizes of members of shutters as specified in SSR Part-1, Section 8, clause 8.24 (a), complete all as specified and as directed. |
| 50 | S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube,complete all as specified and shown on drawing for SI No. 08095 on Srl Page No. 180 of SSR (Part-II) and as directed. |
| 51 | S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement,,complete all as specified and shown on drawing for SI No. 08080on Srl Page No. 176 of SSR (Part-II) and as directed. |
| 52 | S&F 75mm size stainless steel butt hinges, medium weight, cold rolled, mild steel, complete all as specified and as directed. |
| 53 | S & F for Steel Ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and as directed. |
| 54 | Supplying and fixing steel windows with side hung shutters including projection type hinghs with steel handle, and steel pag stay, complete with glazing bars, dovetailed or welded all as specified. |
| 55 | Supplying and fixing steel windows with side hung shutters including projection type hinghs with steel handle, and steel pag stay, complete with out glazing bars, dovetailed or welded all as specified. |
| 56 | S&F150 mm size aluminium handle, cast type, anodised, complete all as specified and as directed. |
| 57 | S&F 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy, complete all as specified and as directed. |
| 58 | S&F Aluminium anodised barrel towerbolt, 200 mm long of extruded section, complete all as specified and as directed. |
| 59 | S&F Aluminium anodised barrel towerbolt, 150 mm long of extruded section, complete all as specified and as directed. |
| 60 | S&F in repairs Harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc of 25 mm bore complete all as specified and as directed. |
| 61 | S&F stainless steel wire cloth. 0.36mm nominal dia of wire and average width ofaperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and as directed. |
| 62 | S & Faluminium powder coatedframe for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified complete all as specified and directed.Notes:- (i) Weight ofAluminium sections as per actual or as per IS or as per manufacturer, whichever is less, shall only be considered for payment. (ii) The accessories (including Aluminium mongries etc) required to be provided for windows, vents and doors as per directions of Engineer-in-charge shall be provided but weight for the same shall not be considered.(iii) Cost of all the items,accessories & Aluminium mongries required for the entire completion of the work shall be deemed to be included in the quoted rate.However glass panes, wire cloth shall be measured and paid separately under respective items |
| 63 | S & F aluminium powder coated (minimum thickness of powder coating 50 micron) frame for doors, windows, ventilators, partitions with extruded built up standerd tubular sectiond/appropriate Z sections and other sectionsapproved make conformunf to IS:1285 fixing with dash fastners of required dia and size includig necessary filling up the gaps at junctions i.e at top, bottom and sides requried EPDM rubber/neoprene filling up the gaps at junction with one or more rebates including joining cleat for fixing etc. aluminium sections shell be smooth, rust free ,straight, mitred and jointed mechanically wherver required includingbeading gor glazing/paneling complete all as specified complete all as specified and directed.Notes:- (i) Weight ofAluminium sections as per actual or as per IS or as per manufacturer, whichever is less, shall only be considered for payment. (ii) The accessories (including Aluminium mongries etc) required to be provided for windows, vents and doors as per directions of Engineer-in-charge shall be provided but weight for the same shall not be considered.(iii) Cost of all the items,accessories & Aluminium mongries required for the entire completion of the work shall be deemed to be included in the quoted rate.However glass panes, wire cloth shall be measured and paid separately under respective items |
| 64 | S&F 4mm thick sheet glass ofordinary qualityand glazing forAluminium Joinery, in squaresn.exc 0.50 sqm in each pane, complete all as specified and as directed. |
| 65 | S&F 4mm thick one sidefrosted glass ofordinary qualityand glazing forAluminium Joinery, in squaresn.exc 0.50 sqm in each pane, complete all as specified and as directed. |
| 66 | M&L for the Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 Gde E-165, complete all as specified and as directed. |
| 67 | S & F Waste fittings, brass, 32mm bore chromium plated for glazed ware sinks, wash basins, etc.with long screwed shanks and fly-nuts, flange endbedded in red lead cement and other end fixed complete all as specified and as directed. |
| 68 | S&F in repair PVC valveless double syphonic action type flushing cistern low level of 10 Ltr capacity white with inlet ball valve, float, flushing bend & handle including brackets, suitable for both Indian Type Water Closet & Europeon Type Water Closet including brackets & connection to pipe etc complete all asspecifiedand as directed |
| 69 | S&F as in repair 15mm bore Pillar taps fancy type, with long swan neck , chromium plated, screwed down high pressure, with or without lettered `Hot\" or `Cold\" with long screwed shanks and fly-nuts, screwed for iron pipe and fixedall as specified and as directed |
| 70 | S&F in repair 15 mm Stop valves/ angle valve fancy type cast copper alloy with chromium plated, screwed down, high pressure, screwed both ends for iron pipe or for unions and fixed.complete all asspecifiedand as directed |
| 71 | S&F in repair 15 mm Stop valves (concealed type long shanks)fancy typecast copper alloy with chromium plated, screwed down, high pressure, screwed both ends for iron pipe or for unions and fixed.complete all asspecifiedand as directed |
| 72 | S&F in repair bib tap fancy type cast copper alloy chromium plated screwed down screwed for iron pipe or brass ferrule or fixed for 15 mm dia bore pipe complete all as specified and as directed |
| 73 | S&F in repairs 600x 450mmbevelled edge mirror of decorative type, selected qualitymounted on and including 6 mm thick commercial plywood and provision of wooden plugs with chromium plated brass screws and cup washers for fixing, complete all as specified and as directed. |
| 74 | S&F in repair Brass chromium plated shower rose 125mm size with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and directed. |
| 75 | S&F in repairs tubular towel rail, 20mm dia, D type, brass chrormium plated, 600mm long between flanges, complete all as specified and as directed. |
| 76 | Taking down steel tubing & connections including cleaning for refing serviceable pipe or removal balance pipe of 15 mm dia bore complete all specified . |
| 77 | Taking down steel tubing & connections including cleaning for refing serviceable pipe or removal balance pipe of 20 mm dia bore complete all specified . |
| 78 | Taking down steel tubing & connections including cleaning for refing serviceable pipe or removal balance pipe of 25 mm dia bore complete all specified . |
| 79 | S&F 15mm bore medium grade, galvanized steel tubing (including in short lengths) with and including all fittings, including taking downcomplete all as specified and as directed. |
| 80 | S&F 20mm bore medium grade, galvanized steel tubing (including in short lengths) with and including all fittings, including taking downcomplete all as specified and as directed. |
| 81 | S&F medium grade galvanized steel tubingwith all fittings & fixed complete to walls & ceiling or laid in floors 25 mm dia bore pipe (including in short length) complete all as specified and as directed |
| 82 | S&F laying of CPVC pipes SDR 11& plain CPVCSDR 1120mm outer dia laid in trenches/wall complete all as specifed |
| 83 | M&L Cutting chases,pinning making good to facing where required and pointing in CM 1:3 for concealled water tubing etc and making good cutting n.exc 10cm girth complete all as specified |
| 84 | Supply and fixas15 mm dia 450 mm long PVC connection pipe with two PVC PTMT nuts at each ends with rubber washer complete all as specified and directed. |
| 85 | Taking down PVC drain pipes ( any size or pattern) including all fittings head shoes etc complete all as specified and as directed |
| 86 | S&F 110mm PVC (SWR) as in drain pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed |
| 87 | S&F 110mm bore PVC (SWR) vent cowl complete all as specified and directed |
| 88 | S&F 110mm bore PVC (SWR) `P\"or \"S\" trape complete all as specified and directed |
| 89 | S&F 110mm bore PVC (SWR), junction single, (Single T) equal or unequal complete all as specified and directed |
| 90 | S&F110mm bore PVC (SWR) bends any radius complete all as specified and directed |
| 91 | S&F 75 mm PVC (SWR) as in drain pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed |
| 92 | S&F75mm bore PVC (SWR) bends any radius complete all as specified and directed |
| 93 | S&F grating doom 100mm dia of PTMT (minimum weightt 25 gm) for floor trap/nahani trap all as specified and directed. |
| 94 | S&F in repairs Vitreous China Wash Down Water closet (Pedestal Pattern) 1st quality,white (excluding flushing cistern & flush pipe) including plastic water closet seat white, closed pattern with flat bottom and cover and mild steel CP or aluminised huiging device, making connections, complete all as specified and as directed. |
| 95 | S&Fhand shower (Health Faucet) ABS Body with 8 mm dia, 1.25 mtr long flexible tube & wall hook etc complete all as specified and as specifed and as directed. |
| 96 | M&L for PCC 1:3:6 type C-2 (using 40mm graded stone aggregate) asin foundation filling and mass concrete complete all as specified and directed. |
| 97 | Excavating in post holes (or similar) in soft/lose soil each n exc 0.5 cum getting out returing filling and mass concrete complete all as specified and diected |
| 98 | Taking down carefully existing aluminium point wiring (light / fan / socket or power point) complete, with all fittings such as switch socket combination, switches, sockets, regulator, ceiling rose, utility light fittings and lamp holders etc and making good the disturbed surfaces of walls, roof and floor etc to match with the existing specification, complete all as specified and as directed. |
| 99 | Taking dwn old/unsv distribution board by disconnection of electric connection carefully SPN DBs/TPN DBs/Main Switch including old Unsv MCCBs/MCBs, isloators , etc and making good to disturbed surface complete all as specified and as directed. |
| 100 | M&L for point wiring for one light point/ one fan point/ one exhaust fan controlled by 1 one way switch with 1.5 Sqmm PVC insulated unsheathed single core multi-stranded copper conductor (FRLSH) cable 1100 Volts grade drawn through and including rigid non metallic PVC concealed conduit (medium grade) of suitable dia, (also including conduit fittings, along with 1.5 sqmm continuous PVC insulated unsheathed single core multi-stranded copper conductor (FRLSH) cable for earth continuity wire, connected to earth dolly and to be terminated in and including factory made anodized pressed steel sunken boxes (Having wall thickness not less than 1.22 mm for boxes suitable size and beyond that the wall thickness shall be not less than 1.63 mm), concealed type with and including 3mm thick bakelite sheet cover for mounting switches, sockets, fan regulators etc, testing on completion also including cutting chases for concealed conduit, steel boxes etc, pinning in, making good the surfaces in CM (1:3) tofor One light /Fan point controlled by one, one way switch match with the adjoining surfaces , complete all as specified and as directed. |
| 101 | All as per item No 100 here-in-before but for one 3pin 5 Amp switch socket outlet, independent board , complete all as specified and as directed. |
| 102 | All as per item No 100 here-in-before but for one fan point/exhaust fan point controlled by one wayswitch 5ampon the same board complete all as specified and as directed. |
| 103 | All as per item No 100 here-in-before but for one 3pin 5 Amp switch socket outlet,same boardcomplete all as specified and as directed. |
| 104 | All as per item No 100 here-in-before but for one 5/15 Amp switch socket outlet, independent with 2.5 Sqmm single core multi-stranded copper conductor cable (FRLSH) along with 2.5 sqmm continuous PVC insulated unsheathed single core multi-stranded copper conductor (FRLSH) cable for earth continuity wire, complete all as specified and as directed. |
| 105 | Supply and fixing switch piano type, single pole, 5 amps, complete all as specified and as directed. |
| 106 | Supply and fixing switch piano type, single pole, 15 amps, complete all as specified and as directed. |
| 107 | Supply and fixing switch socket , 2 in 1, 5pin, 5 Amp,complete all as specified and as directed. |
| 108 | S&F switch socket outlet, 2 in 1,6pin,5 and 15 amp, complete all as specified and as directed. |
| 109 | S&F ceiling rose, 3 phase /PVC/Polycarbonate, isolated body, complete all as specified and as directed. |
| 110 | S&F electronic fan regulator, flush type (Delux model), rotary step type, 5 step, not less than 100 watt, complete all as specified and directed. |
| 111 | S&F MCB, SPN, DB, 8 ways, double door, Metal door, IP-43 IK 09 in 100Aprotection, isolated neutralbar, insulated busbar assembly complete including provision of blanking plates as required & fixed flush to wall and making good the disturbed surfaces in CM 1:3, completeall as specified and directed. |
| 112 | S & F for sheet metal enclousre MCB DB TPN 4 way with 200 Amps rated bus bar 240 volts double door with magnitic locking system including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall , complete all as specified and directed. |
| 113 | S & F forMCB Three pole and neutral rated capacity 6 to 32 amp rating 240V, breaking capacity10KA \"C\" curveand currentindication for individual pole and designed based on advanced current limiting hammer trip mechanism ,complete all as specified and directed. |
| 114 | S & F MCB single pole and neutral rated capacity 6 to 32 amp rating 240V, breaking capacity10KA \"C\" curveand currentindication for individual pole and designed based on advanced current limiting hammer trip mechanism ,complete all as specified and directed. |
| 115 | S & F in replacmentMCB single polerated capacity 5 to 32 amp rating 240V, breaking capacity10KA \"C\" curveand currentindication for individual pole and designed based on advanced current limiting hammer trip mechanism ,complete all as specified and directed. |
| 116 | Supply and fixing LED tube light batten type made of CRCA sheet with decirative end caps suitable with ultra bright glass LED tube light 1x18/20 watt T8 type single side connection complete with both end bi-pin holder and all accessories internally prewired and fixed to wall/celling incl fittings accessories and connecting up with twin core fexible copper conductor cable suitable size all as specified. |
| 117 | S & F energy saving new generator enviromental friendly long life versatile presure die cast aluminium IP 66 for securty ligh fitting luninaire with high power LEDs as light source (100 Im/watt) with LDR sensor for automatic ON/OFF operation and electronic driver of capacity 25 watts with pre-wared and necessary mounting arrangements and provison of 1.5 sq mm three core copper conductor cable multi stranded from ceiling rose to light fitting including necessary dia GI pipe medium grade braket 1.5 mtr long bend to requred shape with clamps, nut bolts including painting of mild steel flat iron surfaces with two coats of synthetic enamel paint over a coat of red oxide primer , complete all as directed by Engineer-in-charge. |
| 118 | Taking down ceiling fan/exhaust fan any sweep, keeping with safe custody and refixing the same with replacement of unsv 3core PVC insulated sheathed multistanded copper conductor cable of size 23/0.193 from ceiling roseto fan terminal, complete all as specified and directed by the Engineer-in-charge. |
| 119 | S&F energy saving BLDC ceiling fan; 5 star rating, Type of motor - Brush Less DC Motor (BLDC) and Input Power - 32 to 35 Watts with full speed and reduced power consumption with reduced speed technology, Voltage- 90-300V AC, 50Hz, single phase, RPM - 340 to 375 rpm, Blades- Decorated, Sweep - 1200 mm, Air delivery - Not less than 210 CFM with service value 6.00 BEE and Colour - Glow white/ Toast Brown/ Gloss Black or others as approved by GE,complete all as specified and as directed. |
| 120 | S & F for energy Exhaust fan of 300 mm sweep made of metal body Ventil Air-DS type complete with louver with botls nuts and washers size of the bolt 15 cm long 12 mm dia embedded in the wall including provision of PVC flexible copper cable of size 23/0.0076 two core from ceiling rose to exhaust fan for connection and making suitable size of hole to existing brick wall for fan base complete all as specified and directed. (Note: Cost of suitable opening wall for fixingexhaut fan is deemed to be included in overall rate quoted). complete all as directed and specified. |
| 121 | S & F for energy Exhaust fan of 250 mm sweep made of metal body Ventil Air-DS type complete with louver with botls nuts and washers size of the bolt 15 cm long 12 mm dia embedded in the wall including provision of PVC flexible copper cable of size 23/0.0076 two core from ceiling rose to exhaust fan for connection and making suitable size of hole to existing brick wall for fan base complete all as specified and directed. (Note: Cost of suitable opening wall for fixingexhaut fan is deemed to be included in overall rate quoted). complete all as directed and specified. |
| 122 | S & F for wall mounted LED tube light fitting 10 watts batten for surface mounted, anodized extruded aluminium housing , high transmissitivity diffuser , high lumen output box type fitting , 230 volts and intregated electronic driver connector block etc , complete with all accessories internally pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193from ceiling rose to fitting complete all as specified and as directed. |
| 123 | S &for in replacment of 36W LED square Type 2\"x2\" recessed mounted downlighterwhite powder coated CRCA housing high translucent frosted diffuser, efficacy.100lm /Watt, high performance electronic integral driver , THD,10%, PF.0.95 (warm,white/natural white Colour) & all accessories etc complete all as specified and as directed. |
| 124 | S & installation and testing ofElectric water heater , storage vertival type BEE 4/5 star rated, 25ltr capacity 240 volts 50 Hz comprising of high wattage heating element for instant heating , extre Mild steel with glass lined coated inner tank , rust & shock proof ABS outer body, non-ferrous pressure plate with & including provn of 4 Nos grouting bolts suitably flushed to wall or any other surface including electric connection with 3 core PVC insulated , sheathed, stranded copper conductor cable/flexible chord and one no 15 amps 3 pin plug top etc complete all as specified and directed. |
| 125 | Material and labour for sub main wiring with 2 run of single core PVC insulated (unsheathed) multi stranded copper conductor FRLSH cable of size 4.0 sqmm and onesingle core PVC insulated (unsheathed) multi stranded copper conductor FRLSH cable of size 4.0sqmm as in continuous earth wire drawn into and including concealed PVC conduit, medium grade of 25 mm bore complete with fittings, PVC Junction Boxes, fixings accessories, also including cutting chases, pinning in, making good to facing and pointing in using cement mortar 1:3 and making good disturbed surfaces to match with the adjoining surfaces, including taking down existing sub main wiring complete all as specified and as directed.Note:- For payment purposes, 2 runs of main cable (each of 1RM) 1 run of earth continuity cable (1RM) and one run of conduit (1RM) all together shall be considered as \"1RM\". |
| 126 | M&L for Earthing complete with galvanized steel earth plate electrode 600 mm X 600 mm X 6 mm thick buried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of plate not less than 1.5 m below normal ground level, connected to galvanised earth lead wire 4.0mm diaby means of bolts, nuts, check nuts and washers of galvanized iron or steel, all as shown in Electrical Plate No 3 of SSR Part - I, including necessary excavation and earth work, PCC (1:3:6) type C-1 with 50 mm thick Pre-cast RCC (1:2:4) type B-1 cover slab (reinforced with 8 mm dia deformed bar @ 15 cm C/C both ways and suitable handle of 10 mm dia round bar), including providing charcoal or coke and common salt in alternate layers of 15 cm compacted thickness all around the earth electrode, with funnel and 20 mm bore galvanized iron watering pipe (Medium grade), wire mesh, aluminium lugs, complete in all respect, GI earth strip protected by 15 mm bore (medium grade) galvanized iron pipe and other end connected with main switch board or Earthing test point as directed, including necessary earth work and disposal of spoil to a distance not exceeding 50 m and necessary testing on completion, including dismantling old unsv ones complete all as specified .Note: GI earth wire 4sqmm dia and 15mm bore protection pipe upto 7.5m from earth plate is deemed to be included in the rate quoted be contrator. |
