Tender For Day To Day Repair/ Maintenance In Special Bungalow 1 To 14 Pwd -1 And 2 At Gandhi Nagar Jammu. Cno-481 Np- 1 Dismanteling doors ,windows and clerestory windows (steelor wood) shutter including chowkhats,architrave,holdfasts etc. complete and stacking within 50 meters lead: of area of 3sqm.and below 2 of area beyond 3sqm 3 taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 meters lead : of area of 3sqm.and below 4 of area beyond 3sqm. 5 Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately):2nd class D- wood 6 Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, allcomplete as per direction of Engineer-in-charge. (Note: -Butt hinges and necessary screws shall be paid separately).Second class D- wood : 35mm thick 7 providing and fixing glazed shutter for doors,windows and clerestory windows using 4mm thick float glass panes including ISI marked M.S pressed butt hinges finished of required size with necessary screws 30 mm second class deodar wood 8 Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick . 12 mm thick Coir Veneer Board (conforming to IS: 14842) 9 4 mm thick glass pane (weighing not less than 10 kg/sqm) 10 Providing and fixing wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction of Engineer-in-charge :Second class deodar wood : 30mm thick 11 Extra for using stainless steel grade 304 wire gauge with wire of dia. 0.5 mm instead of Galvanized M.S. Wire gauge with wire of dia. 0.63 mm for doors, windows and clerestory windows with necessary screws: (shutter area to be measured) 12 providing &fixing of ply 19mm thick ply including cutting wasteage fevicol carriage etc complete item of superior make ( green,century,amulya archid ) conforming BWP 710 LMR 13 providing &fixing of ply 6mm thick ply including cutting wasteage fevicol carriage etc complete item of superior make ( green,century,amulya archid ) conforming BWP 710 LMR 14 providing and fixing of 1mm thick sunmica including cutting ,wastage,fevicols nails etc.complete (green,amulya,vigro) LMR 15 providing and fixing of 0.85mm thick sunmica including cutting ,wastage,fevicols nails etc.complete (green,amulya,vigro) LMR 16 providing and fixing 4mm thick straight line teak ply including cutting ,wastage,fevicol,nails,carriage etc.complete (green,century,archid) LMR 17 Providing and fixing of Flush door 30mm thick fixed with 1.00 mm thick sunmica on both sides of (GREEN,CENTURY) including all fitting with mortice lock of make Godrej , Harrison as per direction of EIC 18 providing and fixing nickel plated m.s pipe curtain rods ,with nickel plated brackets including fittings (9.47.2)25mm dia 19 Providing and fixing chromium plated brass curtain rod having wall thickness of1.25mm with two chromium plated brass brackets fixed with C.P. brass screwsand PVC sleeves etc., wherever necessary complete. 20 mm dia. 20 providing &fixing IS Imarked M S pressed butt hinges bright finished with neceesary screws complete:100x58x1.9mm 21 75x47x1.7mm 22 proving &fixing ISI marked oxidized MS sliding door bolts with nuts and screws complete 300x16mm 23 250x16mm 24 proving &fixing ISI marked oxidized MS sliding tower bolts with necessary nuts and screws complete 150x10mm 25 100x10mm 26 proving &fixing ISI marked oxidized MS door latches confirming to IS 5930 with screws complete 250x20x6mm 27 proving &fixing ISI marked oxidized MS handle confirming to IS 4992 with neceesary screws etc. complete .100 mm 28 proving &fixing ISI marked almunium hanging floor door stoper ,ISI marked andized with neceesay screw etc complete single rubber stopper 29 twin rubber stoper 30 providing and fixing magnetic catcher of approved quality in cupboard/wardrobes shuteers including fixing with mecessary screws etc. complete double strip (horizotal type) 31 Providing and fixing special quality bright finished brass cupboard or ward robelocks with four levers of approved quality including necessary screws etc. )75mm 32 Providing and fixing special quality bright finished brass handles with screws etc. complete. 75mm 33 door slider LMR 34 providing and fixing wooden moulded corner beading of size 50x50 mm (baseand height) of triangular shape to the junction of paneling etc. with iron screws,plugs and priming coat on unexposed surface etc. complete.9.113..1 Second class kail wood 35 providing & fixing PVC rigid foam sheet 1mm thick on existing door shutters( bathroom /W.C. doors using synthetic rubber based adhesive 36 Renewing glass panes, with wooden fillets wherever necessary 14.7.2Float glass panes of thickness 5.0 mm (weight not less than 12.5kg/sqm) 37 Renewing glass panes, with wooden fillets wherever necessary 14.7.1Float glass panes of thickness 4.0 mm (weight not less than 10kg/sqm) 38 Refixing of old glass panes with putty and nails 39 Demolishing cement concrete manually/by mechanical means including disposal of material within 50 meters lead as per direction of Engineer-incharge: 1:4:8 or richer mix (i/c equivalent design mix) 40 Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) 41 Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. completeSize of tile 600x600 mm. 42 Dismantling old plaster or skirting, raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 meters lead. 43 Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturers) of 1st quality conforming to IS: 15622 of approved make, laid on 20 mm thick bed of cement mortar 1: 4 ( 1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigment etc., complete. In colour such as White, Ivory, Grey, Fume Red Brown (Khajaria, Somany double charged) 44 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. (Khajaria, Somany) 45 12mm thick cement plaster of mix (1:4)1cement :4 fine sand 46 15mm thick cement plaster of mix 1:4 47 Repairs to plaster of thickness 12mm to 20 mm in patches of area 2.5 sq. meters and under, including cutting the patch in proper shape raking out joints and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50 meters lead With cement mortar 1:4 (1 cement : 4 fine sand) 48 Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. 49 Providing and applying white cement based putty of specified thickness, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete: 1mm thick 50 2mm thick 51 Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface. 52 wall painting with premium acrylic emulsion paint of interior grade having VOC (volatile organic compound ) content less than 50grams /liter of approved brand and manufacture ,including applying addititional coats wherever required to achieve even shade and colour (two coats) 53 Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade, one or more coats on old work. 54 distempering with 1st quality acrylic/oil bound washable distemper( ready made )having VOC (volatile organic compound ) content less than 50grams /liters of approved manufacturer and of required shade and colour complete as per manufacturers ; specifications ,one or more coats on old works , 55 Polishing on wood work with ready mixed wax polish of approved brand and manufacture on New work 56 Earth work in bulk excavation by manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earthlead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge.2.6.1 All kinds of soil 57 Engaging welder including the hire charges welding set and helper for mislaneous welding works at site LMR 58 Cleaning of terrace/loft water storage tank (inside surface area) upto2000 litre capacity at all heights with coconut brushes, duster etc., removal of silt, rubbish from the tank and cleaning the tank with fresh water disinfecting with bleaching powder @ 0.5gm per litre capacity of tank including marking the date of cleaning on the side of tank body with the help of stencil and paint and disposing of malba all complete as per direction of Engineer-in-Charge. (The old date already written on tank should be removed with paint remover or black paint and if date is not written with the stencil or old date is not removed deduction will be made @ Rs. 0.10 per litre) (if during cleaning any GI fittings or ball cock isdamaged that is to be repaired by contractor at his own cost and nothing extra will be paid on this account) 59 providing and laying in position cement concrete of specified grade including curing but excluding cost centtring and shuttering ..all work upto plinth level 1:3:6 (1cement:3course sand :6 graded stone aggregate 40mm nominal size 60 1:2:4 (1cement:2course sand :4 graded stone aggregate 40mm nominal size 61 Demolishing reinforce cement concrete manually/by mechanical means including disposal of unserviceable f material within 50 meters lead as per direction of Engineer-incharge. 62 Demolishing brick work manually/by mechanical means including disposal of unserviceable f material within 50 meters lead as per direction of Engineer-incharge: in cement mortar 63 Reinforced cement concrete works in wall (any thickness) including attached plaster s ,butresses,plinth and string courses ,fillets column ,pillars ,piers ,abutments ,posts and struts upto five level including curing but excluding the cost of centering and shuttering ,finishing and reinforcement with 1:1.5 :3(1cement:1.5 course sand:3graded stone aggregate 20mm nominal size 64 centering and shuttering including strurting ,proping etc removing of form for shelves 65 steel reinforcement for R.C.C. work including straightening,cutting,bending ,placing in position and binding all complete upto plinth level 5.22.4 66 Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in Superstructure including curing in Cement mortar 1:4 ( 1 cement : 4 coarse sand)including extra for upto five floor 67 Extra for brickworkwith common burntclay bricks/cement concrete bricks in superstructurre above plinth level upto floor five level. 68 half Brick masonary with common burnt clay (non-modular) bricks of class designation 7.5 in Superstructure including curing in Cement mortar 1:4 ( 1 cement : 4 coarse sand )upto plinth level 69 Extra for half brickworkwith common burntclay bricks/cement concrete bricks in superstructurre above plinth level upto floor five level.(6.15.2) 70 Structural steel work in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.10.2.2 Welded 71 Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.10.25.1 In stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required, all complete. 72 In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works. 73 providing and fixing of powder coated sheet for various works LMR 74 providing and fixing PVC sheet for partition works LMR 75 Providing & fixing water closet squatting pan (Indian type W.C.pan) with 100 mm sand cast Iron P and S trap, 10 liter low level white PVC flushing cistern, including flush pipe (of approved make) with manulaay cantrolled device ( handle lever) conforming to IS:7231, with all fittings and fixtures complete, including cutting and making good the walls and wherever required: white vitreous china Orissa pattern W.C. pan of size 580 x 440 mm with integral type foot rests 76 Providing and fixing white vitreous china pedestal type water closet (European type W.C pan) with seat and lid , 10 ltr low level white P.V.C flushing cistern, including flush pipe with manually controlled device , conforming to IS: 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required WC Pan with ISI Marked white solid plastic seat and lid 77 Providing and fixing floor mounted, white vitreous china single piece,double traps syphonic water closet of approved brand/make, shape,size and pattern including integrated white vitreous china cistern ofcapacity 10 litres with dual flushing system, including all fittings andfixtures with seat cover, cistern fittings, nuts, bolts and gasket etcincluding making connection with the existing P/S trap, complete inall respect as per directions of Engineer-in-Charge. 78 Providing and fixing wash basin with C.I brackets , 15mm C.P brass pillar taps, 32mm C.P brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required:white viterous china flat back wash basin size 450x300mm with single 15mm C.P brass pillar tap 18.7.7 79 Providing and fixing white viterous china pedestal wash basin completely recessed at the back for the reception of pipes and fittings18.9 80 Providing and fixing stainless steel A ISI 304(18/8) kitchen sink as per I.S 13983 with C.I brackets and stainless steel plug 40mm, including painting of fittings and brackets, cutting and making good the walls wherever required: Kitchen sink without drain board 610x460mm bowl depth 200mm 81 providing and fixing of PVC low level flushing cistern with manually 82 providing and fixing CP brass single lever telephonic wall mixer of quality and make as approved by E.I.C. 18.22.13 83 Providing and fixing mirror of superior glass and of required shape and size with plastic moulded frame of approved make and shade with 6mm thick hard board backing oval shape LMR 84 Providing and fixing of PTMT waste coupling 31mm (18.69) 85 Providing and fixing of PTMTwaste coupling 38mm 86 Providing and fixing ball valve (brass) of approved quality, High or lowpressure, with plastic floats complete. 15 mm nominal bore 87 20 mm nominal bore 88 providing and fixing SS soap case LMR 89 Providing and fixing SS towel rail complete LMR 90 Providing and fixing SS towel ring complete LMR 91 providing and fixing glass shelfs with bracket single set (18.33) 92 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot and cold water supply, including allCPVC plain and brass threaded fittings. This includes jointing of pipesand fittings with one step CPVC solvent cement and testing of jointscomplete as per direction of Engineer-in-charge. 15mm nominal bore 93 20mm nominal bore 94 25mm nominal bore 95 32mm nominal bore 96 40mm nominal bore 97 50mm nominal bore 98 Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc.: 15mm nominal bore 99 20mm nominal bore 100 25mm nominal bore 101 32mm nominal bore 102 40mm nominal bore 103 50mm nominal bore 104 providing fixing of brass bib cock of approved quality 15mm dia 105 20mm nominal bore 106 providing and fixing of ball valve (brass) of approved quality .high or low pressure with plastic floats 15mm nominal bore 107 20mm nominal bore 108 25mm nominal bore 109 Providing and fixing of Vanity Box with complete fitting and fixtures (INCLUDING CENTRAL HOLE MIXER/UNILEVER MIXER) of approved make Jaquar/Cera/Hindware as per direction of EIC 110 providing and fixing CP brass shower rose with 15mm or 20mm inlet 100mm dia 111 providing and fixing unplasticized PVC connection pipe with brass unions 15mm nominal bore : 30cm long 112 45cm long 113 providing and fixing of 15mm nominal bore CP brass short body bibcock (cera,hindware,jaguaar)LMR 114 providing and fixing of 15mm nominal bore CP brass long nose bibcock (cera,hindware,jaguaar)LMR 115 providing and fixing of 15mm nominal bore CP Brass angle valve (cera,hindware,jaguaar)LMR 116 providing and fixing CP Brass pillar cock (cera jaquar)LMR 117 providing and fixing 15mm nominal bore of standard back type CP brass central hole basin mixer pillar tap of approved quality (cera,hindware,jaguar) 118 providing and fixing 15mm nominal bore standard CP brass sink mixer in kitchen and bathroom of approved quality (cera,hindware,jaguar)LMR 119 providing and fixing 15mm nominal bore of standard back type CP brass Health faucet of approved quality (cera,hindware,jaguar) 120 providing & fixing of PVC flexible type waste pipe for sink and wash basinLMR 121 providing & fixing of CP greating in kitchen and bathroom LMR 122 providing &fixing of PVC Pipes for drainage ,severage,rain water flow pipe etc including labour &material costs complete job in all heights(LMR) 4 dia 123 3 dia 124 2 dia 125 Chequerred precast cement concrete tiles 22mm thick in footpath andcourtyard, jointed with neat cement slurry mixed with pigment to matchthe shade of the tiles, including rubbing, cleaning and curing completeon 20 mm thick bed of cement mortar 1:4 ( 1 cement : 4 coarse,dark shade using ordinary cement 126 maintence of existing chequered /onyx tile by replacing damaged tiles with new one joints filling with cement grout (colour pigment matching with tile and colouring etc,including cost of labour and material LMR 127 Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. 2000litre capacity 128 providing and fixing ACP sheet 4mm thick LMR 129 Regrading terracing of mud phaska covered with tiles or bricks, in cement by dismantling tiles or bricks, removing mud plaster, preparing the surfacetof mud phaska to proper slope, relaying mud plaster gobri leaping andtiles or bricks, grouted in cement mortar 1:3 (1 cement: 3 fine sand),including replacing unserviceable tiles or bricks with new ones anddisposal of unserviceable material to the dumping ground (the cost of the new bricks and tiles are excluded) within 50 m leads .(note deduction for the cost of tiles or bricks rate 500.05-200=300.05/sqm) 130 cleaning of roof top / stairs etc area by engaging labour 131 providing and fixing of PVC water tank lids(cover) to cover the top of water tank LMR 132 threaded PVC tank cover LMR 133 shifting of debries /mulba from roof ,stairs momties and adjoining area of blocks to the dumping sites by engaging labours 134 for maintence of severage line and drain by engaging sweaper (cleaner)at site during blockage of severage line LMR 135 providing and fixing of almunium frames for balconies &partion in existing rooms complete job .including the cost of material and labour . LMR 136 providing and fixing of phase for repair of CP mixe/ bib cocks (plain) LMR 137 providing and fixing of phase for repair of CP mixe/ bib cocks (disk) LMR 138 providing and fixing of CP cup for repair of CP mixe/ bib cocks (plain) LMR 139 providing and fixing of CP cup for repair of CP mixe/ bib cocks (disk) LMR 140 proving and fixing washer for repair of brass bibcock LMR 141 carpenter 1st class 142 carpenter 2nd class 143 unskilled labour 144 skilled labour 145 plumber 146 helper for plumber 147 providing and fixing central hole mixtureof jaquar cera eq brand 148 providing and fixing of sink mixtureof jaquar cera eq. brand. 149 engaging trolley for shifting of mulba from site to beyond the muncipality limit including loading and unloading LMR 150 providing and fixing wardrobes with iron sheet hallow frame (4X1/2X2) with 24 guage sheet &shutter with 22 guage sheet including lock and handles (godrej) painting inside with plain paint and outside with tenture paint (Asian,Nerolac,)fixing of frame s either 3inches screw with drill and other works complete jobs ...for frame 151 providing and fixing of wooden frame with iron guage mesh for ventilation in kitchen and bathroom including cost of labour and material 152 providing and fixing of PVC pipe 6 for drainage including all fitting 153 providing and fixing SLIDING CHANNEL 20 154 providing and fixing Hydraulic hinges (Godrej Make) 155 providing and fixing SLIDING CHANNEL 25MM 156 Providing and fixing aluminum die cast body tubular type universal hydraulic door closer (having brand logo with IS: 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete : 157 P/F OF TOUGHEN GLASS COMPLETE FITTING AND STEEL ACCESSORIES. 8mm thick 158 5mm thick 159 providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying (a)after surface preparation ,frst layer of cement @0.488 kg/sqm mixed with water proofing cement compound @0.253kg/sqm(b)laying second layer of fibre glass cloth when the first layer is still green .Overlps of joints of fiber cloth should not be less than 10cm.(c)third layer of 1.5mm thickness consisting of slurry of cement @1.289kg/sqm mixed with water proofing cement compound @0.670kg/sqmand coarse sand @1.289kg/sqm. this will be allowed to air cure for 4 hours following by water curing for 48 hours .the entire treatment will be upto 30cm on parapet wall and tucked into groove in parapet all around 160 providing and fixing of PVC panelling on walls 8 to 10 mm thick inc, all fitting and fixtures complete (wall affair or any equvl. Make) 161 providing and fixing wall paper or required colour shade and design of standard make as directed by the EIC 162 SS HANDLES 12 163 SS HANDLES 10 164 SS HANDLES8 165 Providing / fixing polycorbonate sheet including wastage of 02mm thick complete job 166 Providing / fixing polycorbonate sheet including wastage of 10mm thick complete job 167 Providing and fixing of modular kitchen accessorles of 34.00 of approved specification incl carriage and fixing complete. SS Multi purpose basket 15x20x4 168 SS Multi purpose basket 1520x6 169 SS Multi purpose basket 15x20x8 170 SS Multi purpose basket 15x20x12 171 SS masnal pullout 15x18x18 172 SS Cuttlery basket 15x20x4 173 SS Thali basket 15x20x18 174 wooden flooring 8mm thick 175 Supply, installation, Commissioning and Testing of Auto on/off Pressure Pump 1HP CG Tank 24 ltr of approved Make (Crompton/ kirloskar/servo/ Havells) and specification as approved by Engineer in charge incl all fixtures/fittings complete Job 176 providing and fixing of chimney of approved brand(ELLICA, Faber,GLEN).having capacity of 1350 per cum 177 providing and fixing of check valve brass 2 178 Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL antitermitetreatment. Along wall inside / outer wall floor, wood work extra( drilling of holes and plugging the same and cost of material and labour included )with complet job 179 providing and fixing of english seat cover Please Enable Macros to View BoQ information
