|
| 1 | Taking down shutter of any description exc. 1 Sqm but n. exc. 2 Sqm each complete all as specified and directed. |
| 2 | Taking down chowkhats or frames not exc 1.5 sqm each without taking off shutter from the frame complete all as specified and directed. |
| 3 | Taking down chowkhats or frame exc 1.5 sqm but not exc 4 sqm with shutter (without taking off shutter frome the frame ) |
| 4 | M & L 2nd class hard wood Plain solid , straight chowkhats and frames wrought, framed on the solid, rounded or chamfered, put together with glue pinned at joints, and incl FI hold fast (06 nos in each door) embedded in ( incl) PCC (1:3:6) Type C1 wiring 20mm greded stone aggregate as block etc complete all as directed and directed. |
| 5 | S & F 30 mm thick Flush shutters , solid core construction, with block board core and plywood face panels one face is covered with decorative face veneer with lipping/ frame to match fixed to chowkats complete all as specified and directed. |
| 6 | S & F 2 nd class hard wood35 mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass , gauze, etc, (without sash bar) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc, sizes of members of shutters as specified in SSR Part-I, section 8, clause 8.24(a) fitted to chowkats complete all as specified and directed. Note :- Glass pane and wire mesh shall be measured and paid separately inrespective supply only item. |
| 7 | Suplly only Galvnised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18 mm complete all as specified and directed. |
| 8 | M & L Preparation of New wood or previously untreated surfaces of any description , not otherwise description, over 10 cm width or grith apply two coat of synthetic enemel paint (ordinary tint) over a coat of pink primer complete all as specifed and directed. |
| 9 | S & F PVC solid factory made door frame of size 50 mm x 47 mm made out of 5 mm thick plain colour PVC sheet reinforced with MS square tubecomplete all as specified and directed. |
| 10 | S & F factory made solid panel PVC door shutter 30 mm thick (Style) consisting of frame made out of MS tubes for top and bottom rails. MSframe shall be covered with heat molded plain colourPVC ‘C’ channel having a PVC sheet strip of 20 mm width struck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and gap insert for top rail and bottom rail, paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement complete all as shown in SSR Part – II 2004 and as directed. |
| 11 | S & F 100 mm size butt hinges medium weight, cold rolled mild steel complete all as specified and directed |
| 12 | S & F 100mm size butt hinges, C-21 extruded aluminium alloy with galvanised mild steel hinge pin, anodised ISI marked complete all as specified and directed |
| 13 | S & F aluminium 200 mm long anodised barrel tower bolts ISI marked of extruded section and fixed complete all as specified and directed |
| 14 | S & F aluminium 150 mm long anodised barrel tower bolts ISI marked of extruded section and fixed complete all as specified and directed |
| 15 | S & F 150 mm size aluminium handles cast type, anodised ISI marked complete |
| 16 | S & F in repairs 150mm lengthfloor door stopper of aluminium alloy body and tongue, anodized with hard drawn steel spring, fixed to floorcomplete all as specified and as directed |
| 17 | S & F250 mm aluminium alloy, anodised sliding door bolt ISI marked with hasp, staple (bolt type) and fixing clips of sheet, cast of extruded sections and fixing bolts and sliding bolts of extruded sec or cast aluminium and fixed complete. |
| 18 | S & F powder coated aluminium sliding glazedwindows with three track , three shutter sliding with following specification and making good the adjacent side etc . shifting of existing cooler stand where required complete all as specified and as directed(i)Windows frame of cross section 101mm x 44mm x 1.5mm thick.(ii)Three way track for sliding shutters of cross section91.8mm x 31.75mm x1.1mm thick.(iii)Sliding shutter frame of cross section40 x 18 x 1mm thick.(iv)4 mm thick tintedglass superior quality.(v) IDPE Rubber guasket for fixing of glass.(vi)Locking cleats per shutter -01 Nos.(vii)Sliding rollers per shutter - 02 Nos.(viii) Aluminium wire cloth 0.30mm nominal dia of wire and average width of aperture 1.56mm for shutters 01 Nos.(Ix)fixing screw for frame with wall per windows- 08 Nos |
| 19 | S&F powder coated aluminium ventilator cross section 63.5x38.10x1.5mm consisting of two partions upper portion shall have louvers with 3mm thick pin headed glass and aluminium wire cloth 0.30mm nominal dia of wire and average width of aperture 1.56m fixed with aluminium beads and securing on outer face of frame and lower portion of ventilation shall be fixed with 3mm thick pin headed glass with IDPE rubber gasket including aluminium beads, including preparation of jombs all around in CM 1:3 finishing even and smooth complete all as specified and directed. |
| 20 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed. |
| 21 | M&L mild steel framed work such as grills , gratings, etc., with ends of bars shouldered and/ or riveted, or forged in to spikes; framed guard bars ;barred iron doors; ladders; framed balusters ; walk ways ; railings; frame work of water tanks, door shutter/gate and similar work conforming to Fe-290 Gde E-165 complete all as specified. |
| 22 | M & L for preparation of new or previously untreated steel surfaces of any description over 10 cm in width or girth not otherwise described and applying two coats of synthetic enamel paint over of redoxide zinc chrome coat complete all as specified and as directed. |
| 23 | M&L fly ash brick work with modular brick straight or curved on plan exc. 6 m mean radius built in cement mortar 1:6 including demolition of brick work built in cement mortar complete all as specified and directed. |
| 24 | M & L 10 mm thick rendering in cement mortar 1:6 on brick work or concrete surface, surface finished even and fair,including raking out joints, hacking for key, scrubbing down with water at any height etc complete all as specified and as directed. |
| 25 | M & L applying (by using of roller) two coats of distermper oil emulsion over a coat of primer over and incl minimum 1mm thick wall care putty on wall surface incl preparation of new surface complete all as specified and directed. |
| 26 | M & L applying (by using of roller) two coats of distermper oil emulsion over a coat of primer over and incl minimum 1mm thick wall care putty on wall surface, including complete removal of existing treatment on wall, complete all as specified and directed |
| 27 | M & L vitrified ceramic tiles 09 to 10mm thick (square/rectangular) light shade polished, area of each tiles not exceeding 0.36 Sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm screed bed in cement mortar 1:6, including dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing) andrubbish off the premises complete all as specified and directed. |
| 28 | Description all as per ser item No. 27.00 above but in vertical surface including 10 mm thick rendering in cement mortar 1:4, including dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing) andrubbish off the premises complete all as specified and directed. |
| 29 | S & F Factory made single extruded WPC (Wood Polymer Composite) solid door Chowkats of size 45 x 85 mm double rebate of virgin PVC polymer of K value 58- 60(Suspnsion Grade), calcium carbonate and natural fibres (wood powder/ricehusk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screws with full body threaded star headedSS screws having minimum frame density of 750 kg/cum , screw withdrawal strenght of 2200 N (Face) & 1100 N (Edge) , minimum compressive strenght of 58 N/mm sqr , modules of elasticity 900 N/mm sqr and resistance to spread of flame of Class A category with property of being termite /borer proof , water/mositure prooof and fire retardant and fixed in position with MS holdfast/lugs /SS dash fasteners of required dia and lenght complete as per direction of Engineer-in-Charge . (MS hold fast/lugs or SS dash fasteners etc . |
| 30 | S & F size 25 mm thick Factory made single extruded WPC (Wood Polymer Composite) solid DECORATIVE TYPE FLUSH DOOR SHUTTER of comprising of virgin PVC polymer of K value 58- 60(Suspension Grade), calcium carbonate and natural fibres (wood powder/ricehusk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screws with full body threaded star headedSS screws having minimum frame density of 650 kg/cum , screw withdrawal strenght of 1800 N (Face) & 900 N (Edge) , minimum compressive strenght of 50 N/mm sqr , modules of elasticity 850 N/mm sqr and resistance to spread of flame of Class A category with property of being termite /borer proof , water /mositure prooof and fire retardant . WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS screws complete all as specified and directed. (Note stainless steel butt hinges and necessary scews shall be paid seperately. |
| 31 | S & F butt hinges 100 mm long stainless steel Grade 304, medium weightcomplete all as specified and directed. |
| 32 | S & F 150 mm long barrel tower bolts Stainless Steel Grade 304ISI marked and fixed with screws complete all as specified and directed. |
| 33 | S & F 150 mm long handles D type,Stainless Steel Grade 304ISI marked complete all as specified and directed. |
| 34 | S & F 250 mm long sliding door bolt Stainless Steel Grade 304, anodisedISI marked with hasp, staple (bolt type) and fixing clips of sheet, Stainless steel sections and fixing bolts and sliding bolts of Stainless steel and fixed with nut bolts complete all as specified and directed. |
| 35 | S & F Stainless Steel 20 mm dia curtain rods incl brackets (fixinside CB)complete all as specified and directed. |
| 36 | S&F in repair factory made PVC shelf /partition/wall cladding, paneling of required size consisting of panel of 12mm thick celuka PVC ply and for supporting the hold of shelf /partition and shall provided 3 edges in size 18mm x 18mm as per required length the front side of the edge visible in the front of the shelf / partition to be edge lipped by 18mm width x 1mm thick PVC Sheet of density 600 Kg/Cum manufactured by ISO 9001 - 2015 Cerfified campany , using solvent cement etc.complete as direction of Engr-in-Charge manufacturers specification and drawings. |
| 37 | M & L for excavation in post holes (or similar holes) n.exc 0.5 cum in soft /loose soil on plan and getting out, returning filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering and removing surplus soil to a distance not exc 50m and making good surface all as specified. |
| 38 | M&L for cement concrete 1:3:6 type C2 (using 40mmgraded stone aggregate) in foundation filling & mass concrete as in post complete all as specifed and directed. |
| 39 | S&F MS angle cinfirming to Fe-290 (Gde E-165) as in fencing post, strut, FI in fencing incl cutting tops to shape as directed, drilling holes notching for wire & flat iron for fixing chain link fencing with angle iron post all as specified and directed. |
| 40 | Supply only chain link MS galvanised fencing any size or type, complete all as specified and as directed. |
| 41 | Fixing only chain link fencing including line wires, any mesh, size and type to any typeof standard, rails, straining bolts etc.Including provision of binding wire complete all as specifed and directed. |
| 42 | S&F 6 to 8mm dia , 50mm long MS screw bolts (machine made) with hexagonal or square head at one end and screwed the other, each screwed end to be fitted with washers and one heaxagonal or square n.exc 5cm long complete all as specified and directed. |
| 43 | M&L for mild steel round bars 10mm dia & over cut to length, bent to shape required including cranking, bending etc. complete as in rungs, steps Fe-410-W (Gde.E-250) quality -A 0r Fe290 (gde E-165) all as directed. |
| 44 | S&F mild steel framed work in doors or gate in angle or other section with gusset plates, rails, braces etc complete drilling for fixing and either hooks and bottom hinges grouted in ground or hanging fittings including 375 mm long sliding door bolts confirming to (Fe 410-W Gde E-250 quality -A) complete all as specified and directed. |
