|
| 1 | TEST, SURVEY AND INVESTIGATIONS |
| 2 | Survey investigation and confirmation of utility services:Scope includes thorough survey of the roads, geotechnical investigation and confirmation of alignment of utility services and existing trees as per the scope of work and to the satisfaction of Engineer-in-Charge (All the locations of surface parking) |
| 3 | ROAD WORKS |
| 4 | Scarification for Overlay |
| 5 | Excavation in Soil with Dozer with lead upto 100 metresExcavation for roadway in soil by mechanical means with Dozer including cutting and pushing the earth to site of embankment upto a distance of 100 m ( average lead of 50 metres ), including trimming bottom and side slopes in accordance with requirements of lines, grades and crosssections as per MoRT&H Technical Specification clauses of section 300. |
| 6 | Removal of Unsuitable Soil with Disposal upto 1000 mRemoval of unsuitable soil including excavation, loading and disposal upto 1000 m lead with all lifts but excluding compaction ground supporting embankment/ subgrade, replacement by suitable soil, which shall be paid separatelyas per MoRT&H Technical Specification clauses of section 300. |
| 7 | Preparation and surface treatment of formation Preparation and surface treatment of formation by removing mud and slurry, watering to the extent needed to maintain the desired moisture content, trimming to the required line, grade, profile and rolling with 8-10 tonne smooth wheeled roller, complete as per MoRT&H Technical Specification clauses of section 300.. |
| 8 | Overlay Layers |
| 9 | Subgrade Construction of Subgrade and earthen shoulder with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of Table 300.2 as per MORT&H technical specification clause of section 300. |
| 10 | 401 Granular Sub-base with Well Graded Material (A) By Mix in Place MethodConstruction of granular sub-base by providing well graded material spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per MoRT&H Technical Specification Clause 401.(i) For Grading I Material |
| 11 | Wet Mix MacadamProviding, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the material with water at OMC in mechanical mix plant carriage of mixed material by tipper to site, laying in uniform layers with paver finisher in sub-base/ base course on well prepared surface and compacting with vibratory roller to achieve the desired density as per MoRT&H Technical specification |
| 12 | Sand Filling in foundation trenches as per drawing &MoRT&H technical specification clause 304. |
| 13 | 80 mm thick factory made c.c. interlocking paver block of M-35 GradeProviding and laying factory made chamfered edge Cement Concrete paver blocks of required strength, thickness & size/ shape, made by table vibratory method to attain superior smooth finish using PU or equivalent moulds, laid in required grey colour & pattern over 50 mm thick compacted bed of sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand in footpath, parks, lawns, drive ways or light traffic parking etc. all complete as per specifications & approval/ direction of the Engineer -in-Charge:(a) 80 mm thick c.c. paver block of M-35 grade with approved colour, design and pattern. |
| 14 | PCC Band Between Carraigeway and Paver Block |
| 15 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All work upto plinth level:1:2:4 ( 1 Cement: 2 fine sand : 4 graded stone aggregate 40 mm nominal size) |
| 16 | Kerb Stone & Median |
| 17 | Cast in Situ Cement Concrete M20 Kerb using concrete mixerConstruction of cement concrete kerb with top and bottom width 115 and 165 mm respectively, 250 mm high in M 20 grade PCC on M-10 grade foundation 150 mm thick, foundation having 50 mm projection beyond kerb stone, kerb stone laid with kerb laying machine, foundation concrete laid manually, all complete as per drawings & MoRT&H technical specifications Clauses 409. |
| 18 | Construction of Median and Island with Soil Taken from Roadway Cutting Construction of Median and Island above road level with approved material deposited at site from roadway cutting and excavation for drain and foundation of other structures with all leads and lifts, spread, graded and compacted with plate compactor as per MoRT&H Technical Specification Clause 407. |
| 19 | Painting Two Coats on New Concrete SurfacesProviding and painting two coats with synthetic enamel paint in all shades on new plastered concrete surfaces as per MoRT&H Technical Specification Clause 803. |
| 20 | Marking & Signages |
| 21 | Road marking strips (retro-reflective) of specified shade/ colour using Hot Applied Thermoplastic material with Reflectorising Glass Beads on Bituminous Surface Providing and applying 2.5 mm thick thick road marking strips (retro-reflective) of specified shade/ colour using hot thermoplastic material including reflectorising glass beads@ 250 gms per sqm area by fully/ semi automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater including cost of cleaning the road surface of all dirt, seals, oil, grease and foreign material etc, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35. The finished surface to be level, uniform and free from streaks and holes as per MoRT&H Technical Specification Clause 803.i) Over 10 cm in width Painting Lines, Dashes, Arrows etc on Roads in Two Coats on New WorkRoad Edge Marking - Median edge and Kerb edge |
| 22 | Printing New Letter and Figures of any ShadePrinting new letter and figures of any shade with synthetic enamel paint black or any other approved colour to give an even shade as per drawings and MoRD Technical Specification Clause 1701.(i) Hindi (Matras commas and the like not to be measured and paid for. Half letters shall be counted as half only) |
| 23 | (ii) English and RomanHyphens, commas and the like not to be measured and paid for. Detail for 100 letters of 160 mm height, i.e., 1.6 m |
| 24 | Road Markers / Road Stud with Lense ReflectorProviding and fixing of road stud 100x 100 mm, die-cast in aluminium, resistant to corrosive effect of salt and grit, fitted with lense reflectors, installed in concrete or asphaltic surface by drilling hole 30 mm upto a depth of 60 mm and bedded in a suitable bituminous grout or epoxy mortar, all as per BS 873 part 4:1973. |
| 25 | Retro-Reflectorised Traffic SignsProviding and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of high intensity grade shetting vide MoRT&H technical specification Clause 801.3, fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M 15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per drawings and MoRT&H Technical Specification Clause 801. |
| 26 | ii. 600 mm equilateral triangle - Junction ahead/Junction type/Pedestrian crossing/Parking provision |
| 27 | iii) 600 mm circular - No parking/No stopping/Speed limit/Pedestrian lane/No overtaking |
| 28 | Direction and Place Identification Signs with size more than 0.9 sqm size BoardProviding and erecting direction and place identification retro- reflectorised sign as per IRC :67 made of high intensity grade sheeting vide clause 801.3, fixed over aluminium sheeting, 2 mm thick with areaexceeding 0.9 sqm supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm, 2 Nos. firmly fixed to the ground by means of properly designed foundation with M 15 grade cement concrete 450 x 450 x 600 mm, 600 mm below ground level as per approved drawing and MoRT&H Technical Specification Clause 801. |
| 29 | Delineator Providing and installation of delineators (road way indicators, hazard markers, object markers), 80-100 cm high above ground level, painted black and white in 15 cm wide strips, fitted with 80 x 100 mm rectangular or 75 mm dia circular reflectorised panels at the top, buried or pressed into the ground and conforming to IRC-79 and the drawings and as per MoRT&H Technical Specification Clause 806. Please Enable Macros to View BoQ information |
