Sales : +91-777 804 8217
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 25-12-2025 | Bid Auto Extn Corrigendum | Bid Auto Extn Corrigendum | 30-12-2025 |
| 2 | 18-12-2025 | Bid Auto Extn Corrigendum | Bid Auto Extn Corrigendum | 25-12-2025 |
| Sl. No. | Item Description |
| 1 | Excavation in post holes (or similar holes) each n. exc. 0.50 CUM and getting out, returning filling in and ramming earth in layers n. exc. 25 cm watering and removing surplus soil and making good disturb surface in soft/loose soil complete all as specified and directed. |
| 2 | Surface excavation not exc. 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil. complete all as spd and directed. |
| 3 | S&F Steel work in tubular trusses, posts etcincluding special shaped washers etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St-240complete all as specified and directed. |
| 4 | M & L plain cement concrete type C2 1:3:6 (using 40mm graded stone aggregate) as in foundation, filling and mass concrete completeall as specified and directed. |
| 5 | M & L for hard corebroken bricks of gauge not exc. 63mm, deposited, spread andlevelled in layerfs not exc. 15 cm thick watered and rammed to a true surface of broken stone or boulders etc. |
| 6 | M & L 75 mm thick plain cement concrete type D-2 1:4:8 (40 mm graded stone aggregate) as in sub base complete all as specified and directed. |
| 7 | M & LMachine pressed rubber moulded precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness M-40 Grade including 25 mm Sand filling under floors or in foundations including watering and consolidation complete all as specified and directed. |
| 8 | S & F prepainted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering / clading to wall, fixed with self tapping screws as specified. Complete all as spd and directed. Note:- Necessary cutting ,wastage,forshape as per direction of Engineer -in - chargeshall be deemed to be included in quoted rate. |
| 9 | M & L applying two coats of synthetic enamel paint over a coat of red oxide primer on steelsurfaces over 10 cm width or girth including preparation of surface complete all as specified and directed. |
| 10 | M & L for plain cement concrete1:2:4type B-1 (using 20 mm graded stone aggregate) as in roof kerbs,coping, benchingetc including weathering slightly rounded or chamfered angles and throating complete all as specified and directed. |
| 11 | Excavation over areas not exc. 1.50 m deep and getting out in soft / loose soil complete all as specified and directed. |
| 12 | Removing surplus excavated material (SOIL) to distance not exc. 50 m and depositing where directed at a level not exc. 1.50 m above the starting point complete all as specified and directed. |
| 13 | M & L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed. |
| 14 | M & L for mild steel TMT bars 5 mm dia and over up to and including 10 mm dia as in stirrups, spacer and binders, cut to length, bent to shape required including cranking, bending spirally for hooping for columns and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed. |
| 15 | S & F of rolled mild steel joist, channel, angle, flat iron or Tee sections, fixed independently without connecting plates etc. (cut to ordinary length i.e. within 20 mm of length) confirming to Fe-290 Grade E-165 complete all as specified and directed. |
| 16 | M & L for brick work with fly-ash old size bricks having designation 75 conforming to IS-12894 (2002), straight or curved on plan exc. 6.00 m mean radius built in cement mortar 1:6 complete all as specified and directed. |
| 17 | M & L for providing plain cement concrete, type D-2, 1:4:8 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed. |
| 18 | M & L for rendering 10 mm thick cement plaster on fair faces of brick work or concrete surfaces with cement mortar 1:6 finished even and fair complete all as specified and directed. |
| 19 | M & L for use & waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs etc. also splayes between floors and beams in fair finished surface of concrete complete all as specified and directed. |
| 20 | M & L for providing reinforced cement concrete 1:2:4 (Nominal Mix) type B-1, using 20 mm graded stone aggregate, as in beams, cantilevers, bressummers, lintels over 1.50 m span and the like complete all as specified and directed. |
| 21 | M&L Virified Ceramic tiles 8-10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM 1:6complete all as specfied and directed. |
| 22 | All as per serial item No 21 above but as in vertical surfaces/wall/cladding including rendering 10 mm thickin cement mortar 1:4,complete all as specified and directed. |
| 23 | M&L for 20 mm thick Granite work (table rubbed and polished) in steps, jambs, pillars, window-cills, door cills cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with and like in cement mortar (1:4) including form work , pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite with full round bull nosing edgingcomplete all as spd as directed.Note :- shade and coloured of granite will be approved by Engr-in-charge) |
| 24 | S & F prepainted galvalume aluminium zinc coating GI based Plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering / clading to wall, fixed with self tapping screwsincluding all wastage, cutting etc Complete all as spd and directed. Note:- Necessary cutting ,wastage,forshape as per direction of Engineer -in - chargeshall be deemed to be included in quoted rate. |
| 25 | Taking down Chowkats or frames with shutters (Without taking off shutters from the frames)not exceeding 1.5 Sqm each including iron mongries, hold fast etc andincluding making good disturbed portions of walls in CM 1:4 complete all as specified and directed. |
| 26 | Taking down Chowkats or frames with shutters (Without taking off shutters from the frames)exceeding 1.5 sqm but not exceeding 4.0 Sqm each including iron mongries, hold fast etc and including making good disturbed portions of walls in Cm 1:4 complete all as specified and directed. |
| 27 | S&F 125mmx60mmx1.25mm thick pressed steel, frames for door with one or more rebates including filling and compaction with PCC (1:3:6) Type C-1 using 20 mm graded stone aggregate, necessary fixing lugs, hinges, lock strike plate, etc, complete including wooden texture finished paint on the frame surface complete all as specified and directed |
| 28 | S & F 30 mm thick factory made Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed. |
| 29 | M & L for 35mm thick plain framed glazed and skeleton shutter open rebated& prepared to receive glass, gauge etc, without sash bar edges of framingplain chamfered or rounded fitted with cut and mitered beads for securing glass etc, of 2nd class hard wood , members of shutters as specified in SSR Part - ISection 8 clause 8.24 (a) fitted to chowkats complete all as specified and directed. |
| 30 | Supply and fix Solid PVC door frame of size 50mm x 47 mm made out of 5mm plain colour PVC sheet reinforced with mild steel square tube 47x47mm (19 gauge) all as specified and directed. |
| 31 | M&L for factory made solid panel PVC doorshutter 30 mm thick (style) consisting of frame made out of one side prelam PVC sheet and other side plain pvc sheet. Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing. |
| 32 | S&F in repair steel windows with pressed steel frame (size 95 x 45 x 1.25 mm ) side hung shutter including box type hinges with steel handle and steel peg stay with glazed openable shutter with glazing bar ( open out side ) and wire gauged openable shutter without glazing bar ( open inside ) dovetailed or welded complete all as specified and all as per DRG No TD/088 dt 07 Jan 2002Note :- (i) Two shutters ie wire guaged and glazed shall be fixed in one composite frame and both shutter shall be measured as one unit(II) rate for filling PCC in frame deemed to be included in quoted rates(iii) MS grill,glass and wire mesh shall be measured and paid seperatly under relevant item of schedule |
| 33 | S & F Mild steel work in framed work such as grills, gratings,framed guard bars, ladders etc., with ends of bars shouldered and/ or riveted, or forged into spikes, and similar work confirming to Fe.290.Gde-E-165 complete all as specified and directed. |
| 34 | S & F100 mm long medium weight, cold rolled Stainlesssteel Butt hinges with screws complete all as specified and directed. |
| 35 | S & F200mm long Aluminium, anodised, barrel tower bolts of extruded section complete all specified and as directed. |
| 36 | S & F 150 mm long Aluminium alloy handles, cast type, anodised complete all as specified and directed. |
| 37 | S&F 200mm longmild steel barrel tower bolts, stove enamelled black, with bright bolts complete all as specified and directed. |
| 38 | S & Fmild steelpressed handle, ovaltype, stove enamelled blacksize of handle 125mm ISI marked . |
| 39 | Supply and fixmild steel, sliding door bolts, bolt type, stove enamelled black, with bright bolt not less than 12 mm dia with and minimum of 6 bolts and nuts, four on bolt plate and two on staple plate length of bolt 300 mmcomplete all as specified and directed. |
| 40 | S&Fmild steel 300 mm long ordinary rat rail rodpattern helical door springs, incl roller and roller plate complete all as specified and directed. |
| 41 | S & F Galvanized mild steel wire cloth, 0.56 mm dia of wire and average width of aperture 1.18 mm and fixed with tinned stacks, or galvanized wire staples complete all as specified and directed. |
| 42 | S & F inSheet glass 3.0 mm thick, ordinary quality and glazing with oil putty or wooden beads n exceeding 0.5 Sqm in each pane glazed with putty or fixed with beads complete all as specified and directed. |
| 43 | Demolition of Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed. |
| 44 | M&L for 75 mm thick cement concrete, type C 2, 1:3:6 (using 40 mm graded stone aggregate) as in plinth protection and finishing the surface even and smooth without using extra cement complete all as specified and directed. |
| 45 | M&L for Plain Cement Concrete Type C1 1:3:6 (using 20 mm graded stone aggregate) as in holdfast and similar work etc complete all as specified and directed. |
| 46 | M&L for 100 mm thick cement concrete, type D 2, 1:4:8 (using 40 mm graded stone aggregate) as in sub base of floor complete all as specified and directed. |
| 47 | M& L for providing Cement concrete chequred tiles 25cm x 25cm x 22mm thick, machine pressed; set jointed and pointed in neatcement slurry in floors, and cutincluding dismantling of old tiles complete all as specified and directed |
| 48 | M&L for 25 mm thick PCC 1:2:4 type B1 (using 20 mm graded stone aggregate) in floorings including finishing the surface even and smooth using extra cement complete all as specified and directed. |
| 49 | M&L brickwork with fly ash bricks, straight or curved on plan exc. 6m mean radius built in 1:6 cement mortar including demolition of old brick work complete all specified and directed. |
| 50 | Taking down cement plaster from brick wall/concrete surface includingracking out joints hacking for key and scrubbing down with watercomplete all as specified and directed. |
| 51 | M & L rendering 15mm thick on brick wall or concrete surface in cement mortar 1:6 finished even and smooth without using extra cement complete all as specified. |
| 52 | M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 finished even and smooth without using extra cement complete all as specified and directed.(Note: Water Proofing Compound (if added) shall be measured and paid seperately.) |
| 53 | Material and labour for preparation of new plastered or pointed surface of walls/pillars/cornices by brooming down or by sand papering or by any other mean and after preparing the surfaces applying two coats of cement base paint as approved tint/colour complete all as specified and directed. |
| 54 | M&L for applying two coats of oil bound distempering on newly plastered wall surfcae with airless electric sprayers over a coat of primer applied using airless electric sprayers over one coat of wall care putty of 1 mm thickness complete all as specified and directed. (Note-APPLICATION TO BE DONE THROUGH AUTHORISED APPLICATOR OF MANUFACTURER.) |
| 55 | M&L for preparing newly plastered surfaces of walls and applying three coats of white wash complete all as specified and directed. |
| 56 | M&L for preparation of newwood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coat of Synthetic enamel paint (Ordinary tint) over a coat of pink primer complete all as specified and directed. |
| 57 | M&L for Non - skid Ceramic tiles 7 to8 mm thick area of each tileexceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15 mm thick screed bed 1:6 cement motarincluding dismantling of floor tiling complete all as specified and directed |
| 58 | All as per serial item No 57 as above but as in vertical surfaces including rendering 10 mm thickin cement mortar 1:4, as in rendering complete all as specified and directed |
| 59 | M&L for coloured printed glazed ceramic tiles 7 to 8 mm thick on walls dado/skirting (square/ rectangular) of 350x 250x 7mm/ 450X 350X 7mm jointed and pointed with colouredcementto match including 10 mm thick rendering of cement mortar 1:4, including dismantling of old wall tiling complete all as specified or as directed. |
| 60 | M&L for Non - skid Ceramic tiles 7 to8 mm thick (square/rectangular) area of each tileexceeding 0.11 sqm but not exceeding 0.18 sqm, infloors etc. set and jointed inneat cement slurry andpointed in white or coloured cement to match including15 mm thick screed bed 1:6 cement motar, including dismantling of old floortiling complete all as specified or as directed. |
| 61 | Demolition of Reinforced cement Concrete of any description and in anypositionnot otherwise specifically provided for complete all as specified and direcetd. |
| 62 | Form work to soffits of suspended slabs/chajja/ flat/beam/soffit surface of concrete finishedrough surfaces of concrete not exceeding 200mm thick,complete all as specified and directed. |
| 63 | M&L for RCC 1:2:4 type B1 using 20 mm graded stone aggregate as in Chajjas etc complete all as specified and directed. |
| 64 | S & FRotational moulded polyethylene water storage tanks 500 Litre capacity triple layered (cylindrical vertical with closed top) hoisted and fixed in position including dismantling of old unserviceable water tank capacity exc 250 but n exc. 500 litre complete all as specified and directed. |
| 65 | S & F 15 mm bore Galvanized Steel tubes, medium grade for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floorsincluding taking up or down of 15mm tubes complete all as specified and directed. |
| 66 | S & F 20 mm bore Galvanized Steel tubes, medium grade for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floorsincluding taking up or down of 20mm tubes complete all as specified and directed. |
| 67 | S & F in repairs 15 mm bore CP Bib taps, cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed. |
| 68 | S & F in repairs 15 mm bore Chromium plated Angle/Stop valves fency type(straight or angular), cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and directed. |
| 69 | S & F in repairs 20 mm bore gate valve , cast copper alloy complete all as specified and directed. |
| 70 | S&F in repairs Ball valves 15mm dia high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight15 m m - 2 1 0 g m s ) complete all as specified and directed. |
| 71 | S & F in repairs Chromium plated shower rose 125 mm size with or without swivel joints, any size, including fixing tosteel pipe or union complete all as specified and directed. |
| 72 | S&F for in repairs CP Brass Tubular towel rail, 20mm dia, D type, 60cm long between flanges with both side holders complete all as specified and directed. |
| 73 | Supply and fix in repair 600mm x 450 mm bevelled edge mirror of selected quality glass, mounted on 6 mm thickAC building board or commercial plywood on PVC frame complete all as specified and directed. |
| 74 | S & F in repairs Vitreous China Ware Wash hand basin flat back, size 550x400mm in repairs including cutting for and pinning ends of brackets including PTMT waste coupling and PVC waste pipe 32 mm dia and PVC connection 450mm long with PTMT nuts and fixed on a pair of MS cantilever bracket of appropriate size complete all as specified and directed. |
| 75 | S & F in repairs Fancy type chromium plated with long shank and cup (Concealed type) 15 mm bore Stop valves, cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and directed. |
| 76 | S&F in repair 15 mmdia brass chromium plated , pillar taps fancy type, cast copper alloywith capstan heads screwed down high pressure screwed for iron pipe with or without lettered \"Hot\"or \"Cold\"with long screwed shanks and fly nutsor as specified or as directed. |
| 77 | S & F in repairsSinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers, waste coupling and waste pipe including bedding in cementmortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe over all size 915 mm x 460 bowl size 410mm x 330mm x 160mm fixed complete all as specified and directed. |
| 78 | S&F in repair vitreous China Urinal half stall type white complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement mortar 1:3 including PTMT spreader, PTMT waste coupling, PVC waste pipe complete all as specified and directed. |
| 79 | S & F in repairs Vitreous China Squatting pan of Orissa pattern, size 580x440 mm size white with integral foot rest with Cast Iron `P\" or `S\" trap, front or back inlet andincluding connection to trap and to flushing pipe, anti-syphonage pipe etc., including trap set in and including lime concrete bedding complete including making good to floor (excluding flushing cistern and flush pipe)all as specified and directed. |
| 80 | S & F in repairs 10 litres PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including 32mm PVC pipe for low level cistern L type, brackets fixed on wall complete all as specified and directed. |
| 81 | S&F in repairs PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed. |
| 82 | S&F in repair fancy type glass corner 300mm radius of 10mm thick toughned glass with railing fixed with fancy type screws complete all as specified and directed. |
| 83 | S & F 110 mm bore PVC (SWR) Soil, waste and vent, rain water pipes, drain pipe single socketed in any length with rubber ring joints fixed on walls including Taking down eaves gutters and rainwater pipes (any size or pattern AC/PVC/CI), including all fittings, heads, shoes, bends, swan-necks, etc., complete all as specified and directed. |
| 84 | S & F 75 mm bore PVC (SWR) Soil, waste and vent, rain water pipes, drain pipe single socketed in any length with rubber ring joints fixed on walls including Taking down eaves gutters and rainwater pipes (any size or pattern AC/PVC/CI), including all fittings, heads, shoes, bends, swan-necks, etc., complete all as specified and directed. |
| 85 | S & F 110 mm borePVC (SWR) bends any radius complete all as specified and directed. |
| 86 | S & F 75 mm borePVC (SWR) bends any radius complete all as specified and directed. |
| 87 | S&F 20 mm thick granite stone slabs mirror polished of colour and shade as approved by GE, machine cut bedded & jointed with grey cement slurry and pointed in white cement with admixture of pigment to match the shade of granite stone fixed as in steps, jambs, pillars window cills, cooking platforms & the like etc over a screed bed of 15 mm 1:6 C:M including dismantling of old existing granite complete all as specified and directed |
| 88 | Dismantling timber scantlings 40 sq. cm and over in section, in any position complete all as specified and directed. |
| 89 | S & F in repairs 4mm thick E-Board tiles for insulation and acoustic purpose of size 600x 600mm fixed with and including anodised GI prepaintedsnap grid with 25x25x1.5 mm thick Tee section and 38x25x2 mm thick angle with hanging/supporting arrangements as in false ceiling at bottom at spacing 60 cm centre to centre including necessary GI cleats and 4mm dia GI wire as suspender fixed to ceiling not exceeding 1.20 mtr centre both ways with dash fastners complete and making good disturbed surfaces including taking down old ceiling complete allas specified and directed. |
| 90 | Dismantling of Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings complete allas specified and directed. |
| 91 | S&F Steel work in Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel, hollow circular section or flat sections ) including distance pieces, cleats, nut bolts etccomplete all as specified and directed. |
| 92 | S&F in repair 25 mm dia SSfancy typedroppery rod with decorative design matching brackets as approved and knobs (lattu) or end bracket as required incl fitting with 80 mm long SS screw with 75 mm long wooden gitty of appropriate size in each end & intermediate support complete all as specified and directed. |
| 93 | Formwork to sides of concrete foundations, footings, bases of columns, raft beams, sides and soffits ( if any ) of foundation and plinth beams; and similar work; vertical or batter, finished rough surfaces of concrete, complete all as specified and directed. |
| 94 | Formwork to sides of pillars, posts, struts, piers, columns complete all as specified and directed. |
| 95 | Formwork to chullah hoods, chajjas, troughs and similar items including edges complete all as specified and directed. |
| 96 | M&L RCC Type B11:2:4 using 20 mm graded aggregate as in foundation, footing, plinth beam, base of columns etc complete all as specified and directed. |
| 97 | M&L RCC Type B1 1:2:4 using 20 mm graded aggregate as in columns, pillars, piers, post and structs etc complete all as specified and directed. |
| 98 | M&L RCC Type B11:2:4 using 20 mm graded aggregate as in roof Beams, cantilevers, bressummers, lintels over 1.5m span etc complete all as specified and directed. |
| 99 | M&L RCC Type B11:2:4 using 20 mm graded aggregate as in slab, shelves etc. complete all as specified and directed. |
| 100 | M&L RCC Type B11:2:4 using 20 mm graded aggregate as in chajjas, landings, balconies, canopies, deck slabs and in shelves and the like etc.all as specified and directed |
| 101 | Removing excavated soil exceeding 250m but not exceeding 500m and depositing where directed at a level not exceeding 1.50m above the starting point complete. |
| 102 | M&L sand filling under floor or in foundations including watering and consolidation complete all as specified and directed. |
| 103 | M & L hardcore of broken stone or boulders of gauge n.exc.63mm, deposited,spread and levelled in layers n exc. 15 cm thick, watered and well rammed to a true surface. |
| 104 | M & L 75mm th PCC 1:3:6 type C-2 as in sub base, Floors, Paving, plinth protection, finished even and fair complete all as specified. |
| 105 | M & L for 25 mm thick PCC 1:2:4 type B-0, using 12.5 mm graded stone aggregate as in floors, to receive surface of tile complete all as specified and directed. |
| 106 | S&F steel ventilators fixed type with glazing bars complete all as specified and directed. |
| 107 | M & L sheet glass ordinary quality 4mm thick and glazing with oil putty in squares n.exc. 0.5 sqm each pane complete all as specified and directed. |
| 108 | M&L 40mm thick PCC 1:2:4 (type B-0) for damp proof course to horizontal or vertical surfaces including necessary formwork complete all as specified and directed. |
| 109 | M & L rendering 5mm thick on ceiling in cement mortar 1:4 finished fair and even smooth without using extra cement complete all as specified and directed. |
| 110 | Supply only water proofing compound complete all as specified and directed. |
| 111 | M&L non skid ceramic coloured tiles 7 to 8 mm thick (Square / rectangular ) area of each tile in floors etc.area of each tiles exc 0.11 sqm but n.exc. 0.18 sqm set and jointed in neat cement slurry and pointed in white or colour cement to match, over and including 15 mm thick screed plaster in CM 1:6 complete all as specfied and directed. |
| 112 | M&L glazed ceramic colour tiles in vertical surfaces 450 x 350 x 7mm thick, set & jointed in neat cement slurry and pointed in coloured cement to match coloured tiles laid over and including 15 mm thick rendering in CM (1:4) complete all as specfied and directed. |
| 113 | S&F 110mm dia PVC(SWR) pipes single socketed, in any length with rubber ring joints,fixed to walls. |
| 114 | S&F GI tubing 15mm medium grade with all fitting and fixed complete to walls & ceiling or laid in floors,bore of pipe 15mm dia all as specified and directed. |
| 115 | S&F GI tubing medium grade with all fitting and fixed complete to walls & ceiling or laid in floors,bore of pipe 20mm dia, all as specified and directed. |
| 116 | S&F 40 mm dia Low density polyethylene pipes (LDPE) of pressure rating 6 kgf/ sqcm fixed complete to walls ceilings or in floors etc. all as specified and directed. |
| 117 | S&F Vitreous china wash down water closet (pedestal pattern) white complete, including connection to drain pipe and to flushing pipe antisyphonage pipe etc complete all as specified and directed |
| 118 | S&F Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe complete all as directed by Engr-in-Charge |
| 119 | S&F PVC low level cistern 10 Ltr cap with inlet ball valve, float and handle incl bracket and flush pvc pipe of low or high density or PVC 32 mm dia for low level cistern. complete all as specified and directed |
| 120 | S&F PVC connections 15mm size with PTMT nuts of length 450mm. complete all as specified and directed |
| 121 | S & F for chromium plated stop valves/Angle valve cast copper alloy, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipes 15mm bore complete all as specified and as directed. |
| 122 | S&F brass chromium platedwall mixer 3 in 1, 15mm for mixing hot & cold water screwd down three joints to steel pipes or unions and plugging and screwed to walls complete all as specified and as directed. |
| 123 | S & F Wash basins, Vitreous China (flat back or angle back type) any size, including cutting for and pinning in ends of brackets or erecting stand butfixing of supply and waste pipe complete all as specified and directed. |
| 124 | S & F 15 mm dia brass chromium plated pillar tap fancy type with fly nut capstan head screwed for 15 mm dia pipe complete all as specified. |
| 125 | S&F PVC waste pipe for wash basin & Urinal with complete all as specified and directed |
| 126 | S&F 15mm bore chromium plated fancy type bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule. complete all as specified and directed |
| 127 | S & F chromium plated shower rose withor without swivel joints, any size, includingfixingto steel pipeor union size 125 mmcomplete all as specified and directed |
| 128 | S&F brass chromium plated tubular towel rail, 20 mm dia, D type, 60 cm long between flanges including brackets complete all as specified and directed |
| 129 | S&F 600mmx450mm bevelled edge mirror of selected quality glass mounted on 6 mm thick commercial plywood and fixed to wooden plugs with chromium plated brass screw and cup washer complete all as specified and directed |
| 130 | M&L CI floor trap 75mm with grating incluing jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified and directed |
| 131 | S&F Rotational moulded polyethylene water storage tanks(tripple layer and white in colour) of 500 Litre capacity (cylinderical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I. complete all as specified and directed |
| 132 | S&F ball valve 20mm bore high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed, (minimum weight 210 gms). complete all as specified and directed |
| 133 | S&F gun metal globe or gate valve with iron wheel screwed both ends for iron pipe of 20 mm dia complete all as specified and directed |
| 134 | M&L salt Glazed stone ware drain pipe 150 mm bore grade \"A\" laid in trenches and jointed and testing complete all as specified & directed. |
| 135 | M&L PCC 1:4:8 type D-2 (using 40 mm graded stone aggregate) as in concrete bed to drain pipes including packing under and haunching against the sides of pipe after they are laid and tested for 150 mm dia SWG pipe complete all as specified & directed. |
| 136 | Cutting into existing manholes for concrecting new drains making good to pipe and rendering, cutting out existing benching for and forming brach channel (1/2 Round or 3/4 Section) in cement concrete 1:2:4 type B-1 smooth finished and reformed bending as required internal dia of pipe 150mm. complete all as specified and directed |
| 137 | M&L for applying two coats of oil bound distempering over one coat priming (chalk whitening) on new plastered surfaces,including preparing surface, complete all as specified and directed by Engineer-in-Charge |
| 138 | Material and labour for preparation of new plastered or pointed surface of ceiling by brooming down or by sand papering or by any other mean and after preparing the surfaces applying three coat of white wash as approved tint/colour complete all as specified and directed |
| 139 | Material and labour for preparation ofnew steel and iron surfaces of any description not otherwise described over 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified & directed. |
| 140 | Supply and providing water proofing treatment with polymeric standard water proofing membrane, Aquaflex manufactured by M/s Bengal Bitumen,MULTIPLAS STANDARD, manufactured by STP TEXAS Ltd/Hyperplas manufactured by IWL Ltd having 10 years guarantee for water tightness all as specified and directed and described as under :-(a) Prepartionof RCCroof surface and applying one coat of polymeric modified bitumen 85/25 @ 1.2 Kg/Sqm over a coat of polymeric primer @ 0.30 Kg/Sqm including cleaningsurface, all as per manufacture\"\"s specificationcomplete all as specifiedand directed.(b)Supply & providing waterproofing treatment with polymeric proofingmembrane of 3 Kg/SqmHYPERPLAS STANDARD/MULTIPLAS STANDARD consting of 100 micron HMHDPE film centre core including coating he surface with the compatible primer and torch application of membrane with 10 cm overlaps as required thereof, complete all as specifiedor as directed.(b)applying a coat of Aluminium paint @ 0.20 Litres per Sqm complete as per manufacturer\"s instructions |
| 141 | M & L for 75mm thick Plain Cement Concrete, type D-2, 1:4:8 mix (using 40 mm graded stone aggregates) as in sub base complete all as specified and directed. |
| 142 | M & L Machine pressed precast concrete (rubberised form) interlocking paver block any shape and size confirming to IS-15658-2006 of 60mm thickness M-35 Grade, pointed with grey cement and no pigments, as in path etc laid over including 25 mm thick sand cushioning of existing PCC surfaceunder floors or pavers, including watering and consolidation all as specified and directed by Engr-in-Charge. |
| 143 | M & L for 75 mm thick cement concrete (1:3:6), type C-1 using 20mm graded stone aggregate as in floors, hard standing etc and laidcomplete and finished the even & fair andall as specified and directed |
| 144 | Intrenal & External E/M |
| 145 | Taking down carefully aluminium point wiring any type including battens if any except for ceiling or where not feasible for light/ fan//bell/socket or power and including unscrewing from board, fitting and fixture such as switches,socket, ceiling rose,lamp holder,pendants, bracket and regulator etc and removing material from site including making good disturbed surface to match with the existing surface complete all as specified and directed. |
| 146 | Taking down carefully UNSV main switch DBs of any description of an size in any position complete all as specified. |
| 147 | Material and labour for point wiring with single core FRLS 1100 volt grade cable with multi stranded copper conductor of size 1.5 Sq mm (Nominal area) drawn through and including non metallic rigid PVC conduit medium duty ISI markednot less than 20mm dia, with all conduit accessories, screws (concealed conduit wiring in walls and casing capping on ceiling or roof) including metal box suitable for modular fittings and covered withmodular plateand cover of suitable size with new brass screwsfor mounting switch sockets and regulators and drawing continuous earth wire with and including PVC sheathed 1100 Volts grade cable with strandedcopper conductor of size 1.5 Sq mm (Nominal area) and connected to main earth dolly complete all as specified for:-(a) One light / fan/ exhaust fan point controlled by one switch. |
| 148 | All as Per Srl Item No 147 above One 5 pin 5 Amp switch socket out let point on an independent board. |
| 149 | All as Per Srl Item No 147 aboveOne 5 pin 5 Amp socket out let point controlled by one switch on same board. |
| 150 | All as Per Srl Item No 147 above but for one 15 Amp 6 Pin switch socket out let independent with2.5 Sqmm FRLS (Nominal Area) PVC unsheathed copper conductor single core multistrandedincl 2.5 sq mm FRLS PVC copper conductor single core used as earth continuity conductoe complete all as specified.complete all as specified. |
| 151 | S & F Modular switch one way 10 A, 1 Module complete all as specified and directed by the Engr-in-Charge. |
| 152 | S & F Modular switch one way 16 A, 1 Module complete all as specified and directed by the Engr-in-Charge. |
| 153 | S & FModular Socket 6 Amp, 2/3 Pin combined 2 Module complete all as specified and directed by the Engr-in-Charge. |
| 154 | S & FModular Socket 6/16 Amp, 2/3 Pin combined 2 Module complete all as specified and directed by the Engr-in-Charge. |
| 155 | S & FModular fan regulator Step up type, 120 Watt, 2 Module complete all as specified and directed by the Engr-in-Charge. |
| 156 | Supply and Fixing ceiling rose PVC/ Poly carbonate,Isolated body, threeterminal AC 230 volts complete all as specified and directed. |
| 157 | S&F in replacement LED mirror light fitting of 1 x 10 wattLED batten with aluminium housing with all accessories prewired suitable for wall /surface mounting complete with connection all as specified and directed. |
| 158 | S&F in replacement LED mirror light fitting of 1 x 20 wattLED batten with aluminium housing with all accessories prewired suitable for wall /surface mounting complete with connection all as specified and directed. |
| 159 | Supply & Fixing in repairs security light fitting, LED type, 25 Watt, 6000 K, pressure die cast housing with prismatic polycarbonate diffuser & indvl LEDs as light source withintegrated electronic driver complete with M&L GI pipe mounting bracket of size 25/32 mm dia and 1.20 m long fixed to wall with andincluding nut, bolts and GI clamps of size 50 x 6 mm as required including two coats of synthetic enameled paint over a coat of primer and making connection with three core 23/.0076 rubber insulated copper cable from ceiling rose to connector of street light complete all as specified and directed. |
| 160 | Taking down carefully ceiling fan from existing siteand depositedin MES yard for BER in coming BOOall as directed by Engineer-in-Charge. |
| 161 | Supply and fixing ceiling fans complete with blades, down rods, and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed. |
| 162 | Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300mm complete all as specified and directed. |
| 163 | M & L for Hole cutting in wall for fixing of exhaust fan of size 300 mm and good the disturbed surfacres of wallby using putty and match with existing colour of wall complete all as specified and directed.Note:Cost of repairing work and material ( cement and sand) included in quoted rate. |
| 164 | S&F in repairs MCB SPN 40 Amp 240 volt complete all as specified and directed by the Engr-in-Charge. |
| 165 | S&F in repairs MCB single pole 6 to 32 Amp 240 Volt \"B\" curve 10 KA complete all as specified and directed by the Engr-in-Charge. |
| 166 | Supply and fix flush sheet metal enclosure SPN DB 8 way with double door IP-42 protection detachable gland plates, flush mounting for MCB fitted with bus bar , earth bar and neutral linkscomplete all as specified and directed. |
| 167 | Supply and fix flush sheet metal enclosure SPN DB 4 way with double door IP-42 protection detachable gland plates, flush mounting for MCB fitted with bus bar , earth bar and neutral linkscomplete all as specified and directed. |
| 168 | Material & Labour for earthing complete including taking out old unsv and replacewith galvanised steel earth plate 600x600x 6mm thick, buried directly in ground (earth pit not less than 2.25 mtr deep below ground level ) with top edge of the plate not less than 1.5 meters below normal ground level, surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15 cm all around the plate using 4 mm dia GI wire as earth wire electrode moulded and rivetted to earth plate at one end and connected to main switch/ control switches of buildings at another end, GI earth wire encased inand including 15 mm dia GI \"light grade\" pipe from upper end of earth plate upto main switch board of building including 20 dia bore GI pipe \"light grade\" as water pipe from earth chamber andincluding excavation and earth work, PCC 1:3:6 typeC1 chamber and MS angle iron frame 40x40x3mm and RCC cover 40mm thick (1:2:4) type B1 using 20mm graded stone aggregate reinforced complete all as specified and directed. |
| 169 | Taking down carefully serviceconnections of any description from pole, wallor service brackets etc including making good disturbed surface to match with the existing surface complete all as specified. |
| 170 | Supply and laying & testing UG cable XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (Heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10 sq mm, 2 core complete all as specified and directed |
| 171 | Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth and getting out in Soft/Loose soil for laying of LT UG cables/base for Poleetc complete all as specified and directed. |
| 172 | Returning, filling in,including spreading levelling, watering and well ramming in layers not exceeding 25 cm thickin Soft/loose soil complete all as specified and directed. |
| 173 | M&L for sand cushioning laid in trenches for laying of LT UG cables complete all as specified and directed. |
| 174 | M&L Modular bricks common burnt clay building bricks, sub-class ‘B’ designation-75 for LT UG cable protectioncomplete all as specified and directed. |
| 175 | S&F GI tubes light grade of dia 32 mm with all fitting and fixed complete for protection of LT UG Cables laidto walls or in floors or along with poles etc complete all as specified and directed. |
| 176 | S&F LED mirror light fitting of 1 x 10 wattLED batten with aluminium housing with all accessories prewired suitable for wall /surface mounting complete with connection all as specified and directed. |
| 177 | S&F LED mirror light fitting of 1 x 20 wattLED batten with aluminium housing with all accessories prewired suitable for wall /surface mounting complete with connection all as specified and directed. |
| 178 | Supply & Fixing security light fitting, LED type, 25 Watt, 6000 K, pressure die cast housing with prismatic polycarbonate diffuser & indvl LEDs as light source withintegrated electronic driver complete with M&L GI pipe mounting bracket of size 25/32 mm dia and 1.20 m long fixed to wall with andincluding nut, bolts and GI clamps of size 50 x 6 mm as required including two coats of synthetic enameled paint over a coat of primer and making connection with three core 23/.0076 rubber insulated copper cable from ceiling rose to connector of street light complete all as specified and directed. |
| 179 | S&F MCB SPN 40 Amp 240 volt complete all as specified and directed by the Engr-in-Charge. |
| 180 | S&F MCB single pole 6 to 32 Amp 240 Volt \"B\" curve 10 KA complete all as specified and directed by the Engr-in-Charge. |
| 181 | Material & Labour for earthing complete with galvanised steel earth plate 600x600x 6mm thick, buried directly in ground (earth pit not less than 2.25 mtr deep below ground level ) with top edge of the plate not less than 1.5 meters below normal ground level, surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15 cm all around the plate using 4 mm dia GI wire as earth wire electrode moulded and rivetted to earth plate at one end and connected to main switch/ control switches of buildings at another end, GI earth wire encased inand including 15 mm dia GI \"light grade\" pipe from upper end of earth plate upto main switch board of building including 20 dia bore GI pipe \"light grade\" as water pipe from earth chamber andincluding excavation and earth work, PCC 1:3:6 typeC1 chamber and MS angle iron frame 40x40x3mm and RCC cover 40mm thick (1:2:4) type B1 using 20mm graded stone aggregate reinforced complete all as specified and directed. |
| 182 | Notes:- Tenderers may note that amount as given in schedule of credit will be deducted from the total amount to worked out the net contract sum at the time of Acceptance of tender. |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2025 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
