Tender For Special Repair To Building No T-5/6 At Ganeshbari Under Ge Dinjan No 2; 1 Dismantling asbestos cement sheet, ridge(corrugated, semicorrugated, plain etc.) in roof covering,wall etc or of similar types complete allas specified and directed. 2 Dismantling of timber scantlings 40 sqcm & over in section framed work complete all as specified and directed. 3 Taking down chowkhats or frames with shutters without taking off shutters from the frames not exceeding 1.5 Sqm each complete allas specified and directed. 4 Taking down chowkhats or frames with shutters without taking off shutters from the frames exceeding 1.5 Sqm & not exceeding 4Sqm eachcomplete allas specified and directed. 5 Demolition of cement concrete (unreinforced) in ground floors of any description (below or above ground level) complete allas specified and directed. 6 Dismantalling of reinforced cement concrete of any description and in anypositionnot otherwise specifically provided for complete in all respect as specified and directed. 7 Taking down cement plaster of any thickness and description on brick/concrete/stone walls, ceilings, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete allas specified and directed. 8 Taking downplastering onlathing (other than wire-netting), without removing lathing, in cement mortar (one side only measured in cases where both sides are plastered complete allas specified and directed. 9 Hacking out old broken glass (any thickness, size, quality or description) from wooden/steelframes or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete allas specified and directed. 10 Demolition of brickwork or stone/ boulder masonry, built in cement mortar complete all as specified and directed. 11 Dismantling wooden weather boarding of any description fixed in any position with nails/ screws complete all as specified and directed. 12 Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish offt the premises complete all as specified and directed. 13 S&F coloured 0.50mm thick pre-painted galvalume aluminium zinc coating GI based trapezoid profile steel sheethaving tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws alongwith bitumen washer complete allas specified and directed. 14 S&F coloured 0.50mm thick pre-painted galvalume aluminium zinc coating GI basedtrapezoid profile steel sheethaving tensile strength of 550 Mpa as in ridge, valley gutter or of similar type, fixed with self tapping screws alongwith bitumen washer complete allas specified and directed.Note- The measurement shall be carried out as in a plain sheet. 15 S&F coloured 0.50mm thick pre-painted galvalume aluminum zinc coating GI based plain steel sheethaving tensile strength of 550 Mpa as in eves board/ covering or of similar type, fixed with self tapping screws alongwith bitumen washer fixed over mild steel flats, angles etc fixed with framed structure complete allas specified and directed. 16 S&F Rooftrusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, tubular/hollow section, channel or flat sections) including distance pieces, cleats etc. using Fe-410W (Grade E-250 quality A) including necessary welding complete complete allas specified and directed. 17 M&L in repair for second class HW scantalling, wrought, in any position for framed work , jointing with necessary nails, nut bolts etc including necessary supports for truss structure complete allas specified and directed. 18 S&F second class HW plain,solid,straightchowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinnedat joints complete allas specified and directed. 19 S&F in the frame at site,factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement,as per specification & drawing complete allas specified and directed. 20 S&F in opening, solid PVC Door Frame of size 50mm x47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, as per specification & drawing complete allas specified and directed. 21 S&F rolled section as in framing for door/vent/CB/chowkhats, wind tieand the like using angle, tee, hollow tubes etc., cleat and connecting plates complete (Butt hinges shall be measured and paid for separately) using Fe 410-W (Gde-E-250) quality A complete allas specified and directed. 22 S&F mild steel work such as in guard bars, grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; and of similar type of work conforming to Fe 290, Gde-E-165complete allas specified and directed. 23 S&F 30mm thick second class HW glazed andskeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars),edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc,sizes of members of shutters as specified inSSR Part I, Section 8, clause 8.24(a) complete allas specified and directed. 24 S&F 30mm thick glazed and skeleton (30mm thick in 2nd class hardwood) without sash bars for window,ventilators as per SSR Part I , section 8 clause 8.24(b) complete allas specified and directed. 25 S&F 30mm thick glazed and skeleton(30mm thick in 2nd class) hardwood with sash bars for window,ventilators as per SSR Part I , section 8 clause 8.24(b) complete allas specified and directed. 26 S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples fixing with beads in door/window/ventilator/fixed glazingshutters complete allas specified and directed. 27 S&F 75mm size stainless steel butt hinge(ISI marked) complete allas specified and directed. 28 S&F 150mm length of bolt, Aluminium anodised, barrel tower bolt of extruded section complete allas specified and directed. 29 S&F 125 mm size, Aluminium handle cast type anodised complete allas specified and directed. 30 S&F aluminium anodised sliding door bolts with hasp and staple (boil type) 19mm dia bolt 300 mm long complete allas specified and directed. 31 S&F 100mm size mild steel butt hinges complete allas specified and directed. 32 M&L for preparation of new undecorated wooden surfaces with pre mixed wood filler used as putty of grith exc 10cmand applyingtwo coats of synthetic enamel paintover one coat of pink primer before painting complete all as specified and directed. 33 M&L for preparation of old decorated wooden surfaceswith pre mixed wood filler used as putty of grith exc 10cmand applying two coats of synthetic enamel paint complete all as specified and directed. 34 M&L for preparation of new undecorated steel surfaceswith pre mixed steel filler used as putty for steel work and applying two coats of synthetic enamel paint over one coat of red oxide zinc chrome primer before painting complete all as specified and directed. 35 M&L for preparation of old undecorated steel surfaces with pre mixed steel filler used as putty and applying two coats of synthetic enamel paint complete all as specified and directed. 36 M&L for preparation of newly plastered surface of wall and applying two coats of weather coat over 2 mm thick wall care putty over a coat of primer including necessary preparation of surface, complete in all respect as specified and directed. 37 M&L for preparation of old decorated plastered surface of wall after complete removal of existing treatment and applying two coats of weather coat over 2 mm thick wall care putty (in two layers) over a coat of primer including preparation of surface, complete in all respect as specified and directed. 38 M&Lfor preparation ofnew surface of plastered wall using wall care putty to fill the voids and applying two coats of oil bound distemper and finished another one coat with spunge roller overincluding one coat of alkali resistant priming paint before distempering complete all as specified and directed. 39 M&L for preparation of old decorated surfaces including washing, rubbing down and stopping of white wash surfaces of walls (Plastered or un-plastered) including cormices pilasters etc and using wall care putty to fill the voids and applying two coats of oil bound distemper and finished another one coat with spunge roller including one coat of alkali resistant priming paint before distempering complete all as specified and directed. 40 M & L brick work with sub-class B, old size bricks of class designation 75, straight or curved on plan exc. 6m mean radiusbuilt in CM (1:6) including dismataling of brick work built in cement mortar in any position complete in all respect as specified and directed. 41 M & L 15mm thick plastering on brick/stone/concrete surafces of wall in cement mortar(1:4) finished even and smooth without using extra cement complete in all respect as specifified and directed. 42 M & L 15mm thick plastering on brick/stone/concrete surafces of wall in cement mortar (1:6) finished even and smooth without using extra cement complete in all respect as specifified and directed. 43 M& L 15mm thick plastering on wall in cement mortar(1:4) finished even and smooth without using extra cement on one side of lathing or stone masonary surface other than fair face complete in all respect as specifified and directed. 44 M & L 15mm thick plastering on wall in cement mortar(1:6) finished even and smooth without using extra cement on other side of lathing or stone masonary surface other than fair face on other side of lathing complete in all respect as specifified and directed. 45 M & LGI wire netting 0.90mm dia and 12mm mesh lathing to wood or metal studding, joists, etc. in walls, ceilings, stanchions, beams, etc. including all laps, cutting and waste complete in all respect as specifified and directed. 46 Providing and laying 40mm thick of cement concrete using type B-1, (1:2:4) (using 20mm nominal size crushed and graded stone aggregate) flooring and finished even and smooth using extra cement complete in all respect as specifified and directed. 47 Providing and laying 50mm thick of cement concrete using type B-1, (1:2:4) (using 20mm nominal size crushed and graded stone aggregate) flooring and finished even and smooth using extra cement including spike rolling to make impression of expendable metal, whilst the concrete is green complete in all respect as specifified and directed. 48 Forming Contration (Dummy) joints 30 mm deep x 10 mm wide, filled with sealing compound (1 part of bitument and 3 part of sand) complete in all respect as specifified and directed. 49 Providing and laying cement concrete in coping, hold fasts, using type B-1, 1:2:4 (using 20mm nominal size crushed and graded stone aggregate) or of similar work, etc. including necessary form work etc. complete in all respect as specifified and directed. 50 S & F 4mm thick sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane complete in all respect as specifified and directed. 51 S & F plain fillets. square, rectangular or triangular in section, clean sawn, secured with nails or brads using second class wrought HW sec area exc 13 Sqcm but not exc 25 Sqcm including taking down of framed work complete in all respect as specifified and directed. 52 S&F exposed GI powder coated snap grid frame work for false ceiling in flat or in sloping , of grid size 600x600mm comprising of wall/cleat angle of size 25x25x0.35mm and cross tee of size 24x38x0.70mm with 2mm dia GI wire as suspender and including 3.5-4mm thick decorative, pre -painted, non asbestos board (E-Board) in false ceiling including fixing arrangement from steel/wooden truss of any type including dismantaling of existing false ceiling complete in all respect as specified and directed. Make: Eternit, Everest or equivalent 53 Providing and laying ceramic tiles 7 to 8mm thick (square/ rectangular) area of eachtileexceeding 0.06 sqmbut not exceeding 0.18 Sqm in floors etc., set and jointed in neat cement slurry and pointed in white cement with pigment to match the tile colour over 15mm thick screed bed in cement mortar (1:4) complete in all respect as specifified and directed. 54 Providing and laying ceramic tiles 7 to 8mm mm thick (square/ rectangular) area of eachtileexceeding 0.06 sqmbut not exceeding 0.18 Sqm in skirting/dado etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match tile colour over 10mm thick rendering in cement mortar (1:4) complete in all respect as specifified and directed. 55 Providing and laying plinth protection of 75mm thickcement concrete, using type C-1, (1:3:6) (using 20mm nominal size crushed and graded stone aggregate), laid in alternate penals/bays and finished the surafce even and smooth without using extra cement complete in all respect as specifified and directed. 56 S & F 15mm bore of mild steel tubing, medium grade galvanised with all fittings fixed to walls and ceiling or laid in floors including taking up or down, including necessary cutting, chauging, concealingetc. complete in all respect as specified and directed. 57 S & F 20mm bore of mild steel tubing, medium grade galvanised with all fittings fixed to walls and ceiling or laid in floors including taking up or down, including necessary cutting, chauging, concealingetc. complete in all respect as specified and directed. 58 S & F three layered white in colour rotational moulded made out from LLDPE material water storage tanks of capacity 1000 ltr(cylindrical vertical with closed top) including three tank nipples of 20mm nominal bore dia hoisted and fixed in position including dismantling/taking down of existing old tank all as specified in SSR Part I complete in all respect as specified and directed. 59 S & F PTMT ball valve high pressure 20mm bore dia with epoxy coated aluminium rod & high density plastic ball screwedfor iron pipe complete in all respect as specified and directed. 60 S & F in repair 20 mm bore gun metal globe or gate valve with ironwheel head screwed both ends for iron pipe complete in all respect as specified and directed. 61 S & F in repair PVC valveless, syphonic action type, low level dual flush cistern, 10 liter capacity , white, with inlet ball valve, float and handle including brackets for fixing & flush pipe of polyethylene of required length complete in all respect as specified and directed. 62 S & F PVC connection 15mm size with PTMT nuts of length 450mm complete in all respect as specified and directed. 63 S & F in repairs 15 mm bore fancy type CP finished angle valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed. 64 S & F in repairs long body bib taps of 15mm bore, fancy type CP finish cast copper alloy with crutch handle screwed down for iron pipes complete in all respect as specified and directed. 65 S & F PVC coloured insulated over MS pipe 20mm dia curtain rod with fixing bracket, stops, rollers etc. complete in all respect as specified and directed 66 S & F Tubular towel rail, 20mm dia, D type, 60cm long between flanges cast copper alloy chromium plated finish complete in all respect as specified and directed. 67 S & F 4mm thick of size 600 mm x 450 mm bevelled edge mirror of selected quality decorative type mounted on 6 mm commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washerscomplete in all respect as specified and directed. 68 S & F vitreous china wash down water closet Pan (pedestal pattern) white including plastic water closet seat cover, white, closed pattern with flat bottom, and mild steel chromium plated hinging device (exclusive flushing cistern and flush pipe) complete all as specified and directed. 69 S & F soap container of PTMT fixed with and including chromium plated brass screws and wooden / plastic cleats,complete in all respect as specified and directed. 70 S&Fin repair wash hand basins, vitreous China of size 550 x400mm (flat back or angle back type), including cutting for and pinning in ends of brackets over new angle iron erecting stand embedded in PCC (1:2:4) block including 32mm dia bore waste fitings cast copper alloy chromium plated with long screwed shanks and flynuts flange and beded in redlead cement,PVC waste pipe, PVC connection including 15mm bore dia fancy type CP finish Pillar tap, cast copper alloy with capstan heads, screwed down high presuure, with or without lettered hot or cold with long screwed shanks and fly nuts, screwed for iron pipes complete in all respect as specified and directed. 71 M&L for any colour of granite stone without white spots Granitestone slab 17 to 19 mm thick, as in floor, dado, steps, laid over and including screed bed 15mm thick in cement mortar 1:6, jointed and pointed with white cement mixed with pigment to match the shade of stone including cutting, rubbing and polishing surface, including cutting for wash hand basin, sink, gas pipe holeetc., to the entire satisfaction of the Engineer-in-Charge complete in all respect as specified and directed. 72 S & F PVC (SWR) single (single tee) equal or unequal 75mm bore pipe with access door complete in all respect specified and directed.. 73 S & F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm longcomplete in all respect as specified and directed. 74 S & F 75mmPVC (SWR) Nahani trap, plain with grating including jointing with solvent cementcomplete in all respect as specified and directed. 75 Demolition and breaking up drain pipe 75mm/110mm bore dia (Salt glazed ware,PV C or Reinforced concrete) set in cement mortar complete in all respect as specified and directed. 76 S & F PVC (SWR)110mm bore vent cowl complete in all respect as specifified and directed. 77 S & F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls 110mm bore including necessary MS pipe clamp complete in all respect as specified and directed. 78 S & F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls 75mm bore including necessary MS pipe clamp complete in all respect as specified and directed. 79 S & F PVC (SWR) bends any radius 110mm borecomplete in all respect as specified and directed. 80 S & F PVC (SWR) single (single tee) equal or unequal 110mm bore pipe with access door complete in all respect specified and directed.. 81 S & F PVC (SWR) 75mm bore vent cowl complete in all respect as specifified and directed. 82 S & F PVC (SWR) pipes single socketed in any length with rubber ring joints laying in trenches 110mm bore complete in all respect as specified and directed. 83 S & F PVC (SWR) pipes single socketed in any length with rubber ring joints laying in trenches 75mm bore complete in all respect as specified and directed. 84 M&L for preparing surfaces of wood and wood based materials, new or old, of any description and girth, not otherwise described and treated with creosote oil, complete in all respectcomplete all as specified & directed. 85 S & F PVC (SWR) bends any radius 75mm borecomplete in all respectcomplete all as specified & directed. 86 S & F Vitreous China urinals, (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; including S&F 40mm bore dia CP finish cast copper alloy waste coupling fittin, 40mm dia PVC waste pipe.,complete all as specified & directed. 87 Roughening of surfaces of old concrete floor by picking, sweeping clean, and washing down with water to remove dust, etc. complete all as specified & directed. 88 M&L for Brushing neat cement slurry with 3.00 Kg of cement per sqm complete all as specified & directed. 89 S & F in repairs health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified & directed. 90 S&F 4 mm thick figured glass, pin head type and glazing with oil putty in square n.exc 0.5 sqm in each pane, complete all as specified & directed. 91 S&F in repair vitreous chinaware sqatting pan of size 580 x 440 mm, ORISSA PATTERN with new PVC P or S trap bedded in cement concrete (excluding flushing cistern and flush pipe) with integral foot rests, complete all as specified & directed. 92 S&F in repair for 15 mm bore pipe brass chromium plated (CP) shower rose 125 mm size, fixed to iron pipe, complete all as specified and directed. 93 M&L for Providing and injecting chemical emulsion for Post Constructiona Antitermite Treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.5 litres per sq.m of the vertical surface ofthe sub-structure to a depth of 300mm including excavating channel along the wall and rodding etc. complete in all as specified and directed. 94 M&L for Providing and injecting chemical emulsion for Post Constructiona Antitermite Treatmite Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors, complete in all as specified and directed. 95 M&L for Providing and injecting chemical emulsion for Post Constructiona Antitermite Treatment along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron, complete in all as specified and directed. 96 M & L for taking down copper/aluminium point wiring for light, fan, bell, socket or power socket etc complete, including fixture and fittings such as switches, ceiling roses, pendants,regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit and making good disturbed surfaces of walls, floors, etc complete all as specified and as directed by Engineer-in-Charge. 97 M & L for taking down ceiling fan, any type and size and keep in safe custody for refixing after completion of work, complete all as specified and as directed by Engineer-in-charge. 98 M & L for taking down old submain wiring of any type/ core incl earth wire incl batten/ PVC conduit/ casing capping and making good the disturbed surface to match with the existing complete all as specifid and as directed by Engineer-in-charge. 99 M & L for taking down old MCB DBs of any type and size and making good the disturbed surface to match with existing complete all as specified and as directed by Engineer-in-charge. 100 M & L for taking down old MCB (SP/SPN) of any type and size complete all as specified and as directed by Engineer-in-charge. 101 Material and labour for PVC casing & caping point wiring using approved colour coding as per IS, with multi stranded copper conductor 1.5 sqmm (Nominal area), single core, FRLSH, PVC insulated and unsheathed stranded cable drawn through and including non metallic, heavy duty PVC Casing & caping not less than 20mm dia and its fittings including all tees, bell mouth pieces and fixing accessories such as couplers, saddlers, pipe hooks etc, PVC terminal / junction boxes ISI marked with GI flush boxes / sunken boxes made out of 1.2mm thick of any any type confirming to IS-5139(pt-I) of 1969 and IS:14772-2000 with earth dolly including laminated sheet extended upto 25 mm over sunken box for housing the switches, socket outlets, fan regulators etc with brass screws and brass washers and making good the disturbed surfaces as per existing for one light / fan / bell point contorlled by one switch including 1.5 sqmm single core PVC insulated and unsheathed FRLSH copper cable, 1100 volt grade with multi stranded copper conductor green colour as earth continuity conductor upto common earth and connecting to common earth dollywith suitable size of lugs for one light point/ fan point/bell point controlled by one switch complete all as specified and as directed.NOTES : - (i) The quoted rates shall be deemed to be inclusive for surface conduit /casing caping of suitable size fixed on wall, ceiling surface with using necessary accessories/fittings.(ii) Point wiring & earth wire shall be connected to each & every flush/sunken box. (iii) All screws, fasteners, bolts, nuts & washer shall be cadmium plated & the cost of which is deemed to be included in the quoted unit rates.One Light point/ Fan point/ Exhaust fan point controlled by one, one way switch complete all as specified and as directed. 102 All as per items no 101 above but One Socket outlet 3 Pin, 5 Amp on same board complete all as specified and as directed. 103 All as per item No 101 above but one Socket Outlet Point, 5 Amp on independent board with 1.5 Sqmm cable complete all as specified and as directed by Engineer-in-charge. 104 All as per item No 101 above but one Socket Outlet Point, 15 Amp on independent board with 2.5 Sqmm cable complete all as specified and as directed by Engineer-in-charge. 105 Supply & fix switch piano, flush type single pole, one way 5 Amp, 230 volts complete all as specified and directed. 106 Supply & fix switch piano, flush type single pole, one way 15 Amp, 230 volts complete all as specified and directed. 107 Supply & fix socket outlet multipin 5A-2/3 pin combined flush type, complete all as specified and as directed. 108 Supply & fix socket outlet multipin 5/15Apin combined flush type, complete all as specified and as directed. 109 Supply & fix stepped type electronic fan regulator flush type 230 volt 5 speed control, complete all as specified and as directed by Engineer-in-charge. 110 M&L for ceiling rose, surface Bakelite of three terminals PVC/Polycarbonate,isolated body (ISI Marked), complete all as specified and as directed by Engineer-in-charge. 111 S&F LED Tube lights fitting 1 x 18/20 Watt, 4 feet ,220V AC decorative box type with driver,including fitting fixed on wall/ceiling and connecting up complete withflexible cable white of suitable size and making necessary connection complete all as specified and directed. 112 Supply and fixing of LED street/security light fitting 35 watts with high efficiency long life LEDs with In-built electronic driver complete housed in pressure die-cast aluminium housing covered with polycarbonate cover with IP66 degree of protection including provision of 3 core twisted flexible copper cable of size 1.5 sqmm from connector to ceiling rose to connection of light, complete all as specified and as directed by Engineer-in-charge. 113 Supply & fix street light bracket fabricated out of GI Tubing light grade 32 mm bore bend to the shape as directed and of length 1.5 mtr complete with suitable mounting MS clamp of flat iron size 40x5mm of suitable length 02 pairs including nuts, bolts and washers etc of suitable size complete all as specified and as directed. 114 S&F LED Bulkhead luminaires 1 x 9/10 Watt fitting in engineering plastic housing with clear prismatic diffuser complete with all accessories and connecting up with flexible cable white ofsuitable size and making necessary connection complete all as specified and directed by Engr-in-Charge. 115 M & L for painting of ceiling fans complete, in situ with synthetic enamel paint by spraying, including filling cavities with filler, one coat after cleaning all dust etc including servicing and minor repair complete all as specified and as directed by Engineer-in-charge. 116 Refixing only ceiling fan (taking down against item No 02 above) of any type including provision of flexible copper cable of suitable size from ceiling fan to ceiling rose all as specified and as directed by Engineer-in-charge. 117 Supply and fixing of ceiling fans complete with blades, down rods, electronicregulator and accessories, 230 V, 1200 mm sweep. min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and as directed by Engineer-in-charge. 118 Supply and fixing of exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300mm complete all as specified and as directed by Engineer-in-charge. 119 Supply, installation, testingofSPN distibution board 8 way,double door , IP 43, as per IS 8623including minimum IP 43 degree of protection with built in fully insulated copper bus bar, not less than 100 Amps capacity insulated neutral bar and earth bar, door earthing, reversible doors, PAN assembly for easy installation and also incoming and outgoing connections with suitable size of lugs/thimbles/glands complete including cutting the wall surfaces for flush mounting of DB and making good with cement plaster, putty and paint to match with the existing surfacecomplete all as specified and directed by Engineer-in-charge. 120 S&F MCB 25 to 32 Amp SP&N, 240 volts 10 KA C series with all incoming/outgoing connections with proper size lugs complete all as specified and as directed by Engineer-in-charge. 121 S&F MCB 6 to 32 Amp SP, 240 voltss 10 KA C series with all incoming/outgoing connection with proper size lugs complete all as specified and directed by Engineer-in-charge. 122 M & L for Sub main wiring with two runs of 6 sqmm single core cable FRLSH PVC insulated multistranded, unsheathed, copper conductor cables 1100 Volts grade drawn through PVC casing capping not less than 20mm dia with all fittings and accessories (like Tee, bend etc) etc including 6 sqmm (nominal area) single core, FRLSH PVC casing insulated multistranded, unsheathed copper conductor as earth wire and duly connected to common earth point complete all as specified and as directed by Engineer-in-charge. Note : (a) PVC Casing-caping, two run cables and one run of earth wire will be measured as one length (b) All incoming and outgoing cable shall be connected by using proper lugs & thimbles 123 M & L for earthing complete with galvanized iron earth plate electrode 600mm x 600mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 meters deep below ground level) with top edge of the plate not less than 1.5 meters below normal ground level connecting to GI wire 4 mm as earthing lead by means of bolts, nuts, check nuts and washers of galvanized iron or steel and earth wire protected by 15mm dia GI pipe medium grade and connected to distribution board/earthing test point all as shown in electrical plate No. 3 of SSR Part-I(2009) and testing on completion, complete all as specified and directed. Note :- The unit rate quoted shall also include for excavation, earth work in any type of soil, plain cement concrete 1:3:6 mix, Type C1 pit, 40mm thick RCC 1:2:4 mix type B1 cover reinforced with 8mm dia TMT bras @ 150mm C/C both ways, GI funnel with watering pipe, wire mesh, protection pipe, earth wire up to 7.50m long complete in addition to item No. 1(a) to (e) of preamble (Notes) under sub heading earthing, specified in SSR Part II. 124 Supply and fixing of sheet metal enclosures vertical distribution board VTPN, (MCCB DB) 4 ways, double door, 415 volts with 200 amps rated bus bar IP 43 protection, with shrouded neutral bar and insulated bus bar and earth link, with and includingMCCB 4 pole thermal release type, 100 Amps, 16 KAas incomer and MCBsas out going complete with making suitable size of MS cabinet as per IS dully grouted on the wall (flush) with opening arrangement including making connections with suitable size of lugs/thimbles/glands and making good the disturbed surface matching with existing surface complete all as specified and directed by Engineer-in-charge. 125 Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m deep and getting out in any type soil for layingpipes etc, complete all as directedby Engineer-in-Charge. 126 Supply and laying burnt brick sub class ‘B’ of standard size laid in trenches as protection to cables complete all as specified and as directed by Engineer-in-charge. 127 Supply and spreading fine river sand in trenches for cushioning of under ground cable/filling cable ducts complete all as specified and as directed by Engr-in-Charge at site. Note :- Only punned thickness shall be measured for payment purpose 128 Returning, filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25cm, complete all as directed by Engineer-in-Charge. 129 Removing excavated material to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point, complete all as directed by Engineer-in-Charge. 130 Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power UG cables (heavy duty) 1100 Volts grade with stranded aluminium conductor confirming to relevant IS specifcations of size 25 sq mm 4 core including taking down existing cable/ service wireof any size complete all as specified and as directed. 131 S & F in repairs 40 mm bore, steel tubes, galvanised, light grade with all fittings and fixtures complete fixed to walls, ceilings, pole using suitable clamp/holder bat complete all as specified and directed. 132 M & L for horizontal boring/drilling hole mannual under the road in soft /loose soil without cutting / disturbing the existing road and inserting GI pipe 80/50/40/32 mm bore for drawing the cable complete all as specified and as directed by Engineer-in-charge.Note : (i) Cost of accesories required for making hole/bore deemed to be included in the quoted rate (iii) GI pipe has been measured and paid seperately 133 S & F steel water tubing galvanised medium gradeof size 25 mm bore with all fittings and accessories complete in trenches/ on wall/under road including taking down old existing pipe complete all as specified and directed. 134 Supply and fixing Gun Metal gate valve with iron wheel head, suitable for 25 mm bore pipes, screwed both ends for iron pipe or for union including taking out old one complete all as specified and as directed by Engineer-in-charge.
