|
| 1 | Reparing/Servicing rolling shutters such as removal of top covers tightening/ loosening the springs adjusting the dislocation of parts if any and applying grease to the springs side guides ( 0.40 kg greese/ shutter) after cleaning and refixing the cover in position etc as directed by engineer in charge. [Rate as per observed data] |
| 2 | Providing and fixing 27.5cm long wire spring grade no:2 for rolling shutters of approved brand and specification. |
| 3 | Supplying sylicon sealent and applying over the bolts over the roof wherever required.(Rate shall inclussive of cost of sylicon sealent, labour charges for scaffolding etc.) |
| 4 | Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross-section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminate shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2 mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame.(Item No. 9.121 of DSR 2023) |
| 5 | Providing and fixing to existing door frames. 30 mm thick Glass Fibre Reinforced Plastic (FRP) panelled door shutter of required colour and approved brand and manufacture, made with fire - retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, castmonolithically with 5 mm thick FRP laminate for panels conforming to IS: 14856, including fixing to frames. (Item No. 9.122.1 of DSR 2023) |
| 6 | Painting with silicon & acrylic emulsion based water thinnable sealer of approved brand and manufacture on wet or patchy portion of plastered surfaces :Two coatsDSR 2023 13.51.2 |
| 7 | Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge: In cement mortar Item no:15.7.4 of DSR 2023 |
| 8 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil. Item No.2.8.1 ofDSR 2023 |
| 9 | Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and for all lift, as directed by Engineer-in-charge. Item No.2.6.1 ofDSR 2023 |
| 10 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand) Item No.6.1.2 ofDSR 2023 |
| 11 | Supplying and installing ready made virgin plasticSeptic tank of specified size including the cost of carriage, trenching, placing at the level below ground level as specified as per the direction of engineer in charge:25 flush capacity Analysis similar to 19.33 |
| 12 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)(Item No. 15.2.1 of DSR 2023) |
| 13 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. Nominal concrete1:4:8 or leaner mix (including equivalentdesign mix)(Item No. 15.2.2 of DSR 2023) |
| 14 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinthlevel :1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) (Item No.4.1.8 ofDSR 2023) |
| 15 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinthlevel: 1:1½:3 (1 Cement: 1½ coarse sand (zone-Ill) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) (Item No.4.1.2 ofDSR 2023) |
| 16 | Supplying,filling,spreading & leveling stone boulders of size range 5cm to 20cm,in recharge pit,in the required thickness,for all leads & lifts,all complete as per direction of Engineer-in-charge. (Item No.23.5 ofDSR 2023) |
| 17 | Supplying, filling, spreading & leveling gravels of size range 5mm to10 mm, in the recharge pit, over the existing layer of boulders, in requiredthickness,for all leads & lifts,all complete as per direction of Engineer in-charge. (Item No.23.6 ofDSR 2023) |
| 18 | Providing and laying in position specified grade of reinforced cement concrete,excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) (DSR 2023 Item No 5.1.3) |
| 19 | Steel reinforcement for R.C.C. work including straightening, cutting,bending, placing in position and binding all complete upto plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more. (Item No 5.22.6 of DSR 2023) |
| 20 | Centering and shuttering including strutting, propping etc. and removal of form for :Foundations, footings, bases of columns, etc. for mass concrete etc(DSR Item No 20235.9.1) |
| 21 | Providing and fixing wash basin with C.I.brackets,15mmC.P.brasspillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets,cutting and making good the walls wherever require: WhiteVitreous China Surgeon typewash basin ofsize 660x460 mm with a pair of 15 mm C.P. brass pillar taps with elbow including operated levers (DSR Item No 202317.7.8) |
| 22 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. :-20 mm nominal dia Pipes( Item no. 18.9.2 of DSR 2023) |
| 23 | Providing and fixing on wall faceunplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.75 mm diameter( Item no. 12.41.1 of DSR 2023) |
| 24 | Steel work in built up tubular (round,square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes DSR 2023 item no.10.16.1 |
| 25 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P.brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately). For fixed portion Powder coated aluminium (minimum thickness of powder coating 50 micron)(Item No.21.1.1.2 of DSR 2023) |
| 26 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P.brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately). For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)Powder coated aluminium (minimum thickness of powder coating 50 micron)(Item No.21.1.2.2 of DSR 2023) |
| 27 | Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS:12823Grade l Type ll, in panelling fixed in aluminum doors, windows shutters andpartition frameswithC.P.brass/stainless steel screwsetc.complete as per architectural drawings and directions of engineer-in-charge.Pre-laminated particle board with decorative lamination on both sides(Item No.21.2.2 of DSR 2023) |
| 28 | Providing and fixing glazing in aluminium door,window,ventilator shutters and partitions etc.with EPDM rubber/neoprene gasket etc.complete as per the architectural drawings and the directions of engineer-in-charge .(Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 4.0 mm thickness (weight not less than10kg/sqm)(Item No.21.3.1 of DSR 2023) |
| 29 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. completeat all levels.Granite stone slab of colour black, Cherry/Ruby red Area of slab over 0.50 sqm ( Item No.8.2.2.2 of DSR 2023) |
| 30 | Supplying labour for routine works including all incidentals and services as per the direction of engineer in charge.(First Class Mason-0123) |
| 31 | Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved(Item No.15.60 ofDSR 2023) |
| 32 | Demolishing stone rubble masonry manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge :Incement mortar ( Item no. 15.9.2 DSR 2023) |
| 33 | Random rubble masonry with hard stone in superstructure above plinth level and upto floor five level, including leveling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) at window sills, ceiling level and the like Cement mortar 1:6 (1 cement : 6 coarse sand) (DSR 2023 of item No 7.2.1) |
| 34 | Random rubble masonry with hard stone in superstructure above plinth level and upto floor five level, including leveling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) at window sills, ceiling level and the like.Cement mortar 1:6 (1 cement : 6 coarse sandUsingavailable dismantled Hard stones obtained from dismantling of collapsed/damaged wall) (anaysed based on item No 7.2.1 of DSR 2023) |
| 35 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)(DSR 2023 Item No 4.1.3) |
| 36 | Centering and shuttering including strutting, propping etc. and removal of form for : Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etcItem No. 5.9.2of DSR 2023 |
| 37 | 20mm cement plaster of mix:1:6 (1cement:6 fine sand)(Item no.13.3.2 of DSR 2023) |
| 38 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work(Two or more coats applied @ 1.43ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) (Item no.13.47.1 of DSR 2023) |
| 39 | Fencing with angle iron post placed at required distance embedded in cement concrete blocks, every 15th post, last but one end post and corner post shall be strutted on both sides and end post on one side only and provided with horizontal lines and two diagonals interwoven with horizontal wires, of barbed wire weighing 9.38 kg per 100 m (minimum), between the two posts fitted and fixed with G.I. staples, turn buckles etc. complete. (Cost of posts, struts, earth work and concrete work to be paid for separately). Payment to be made per metre cost of total length of barbed wire used. With G.I. barbed wire(Item No 16.18.1 of DSR 2023) |
| 40 | Providing and fixing hard drawn steel wire fabric 75x25 mm mesh of weight not less than 7.75 Kg per sqm to window frames etc. including 62x19 mm beading of second class teak wood and priming coat with approved steel primer all complete.(DSR-9.50) |
| 41 | Engaging JCB along with diesel truck to clean,level and load the unwanted rubbish,waste etc.In to the truck and making the slope in the surface in the complex as per directions of engineer in charge. |
| 42 | Dismantling aluminium/Gypsumpartitions, doors,windows,fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceable material with in 50 meters lead as directed by Engineer- incharge.(Item No. 15.57 of DSR 2023) |
| 43 | Providing and fixing plain Multipurpose Cement board (High Pressure steam cured) as per IS : 14862, with suitable screws for fibre cement board in ceiling etc. complete : 3 mm thick cement board Similar to KPWD Data 12.26.1 |
| 44 | Providing and fixing radial exhaust turbo ventillators/extractor capacity of minimum 100cuft per minute air circulated fan of 22\" throat dia weight of 5.5kg having throat dia wind ventillator with FRP base plate, including cost of fixing turbo/wind ventillator on new 0.50mm thick pre-coated GI profile sheet roofing on godown roof lincluding the cost of transportation of all materials tools and plants, fixtures & fastenings. Labour, insurance, safety measures etc and as directed by the Engineer in charge including guarantee of turbo ventillators of minimum 03 years and performance warranty etc complete.( HQrs approved rate) |
| 45 | Providing and fixing glazing in aluminium door,window,ventilator shutters and partitions etc.with EPDM rubber/neoprene gasket etc.complete as per the architectural drawings and the directions of engineer-in-charge .(Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 4.0mm thickness (weight not less than 10kg/sqm) (Item No.21.3.1 ofDSR 2023) |
| 46 | Taking out bottom ventillator shutters of the godown from the existing wooden frame , removing old hinges, screws etc and cleaning, refixing the shutters back with new hinges, screws etc as per the directions of Engineer in charge. |
| 47 | Repair to plaster of thickness 12mm to 20 mm in patches of area 2.5 sqm and under, including cutting the patch in proper shape, raking out joints and preparing plastering the wall surface with white cement based polymer modifiedself curing mortar, including disposal of rubbish, all completeas per the direction of Engineer-In- Charge( DSR 2023 Item No14.75) |
