Tender For Various Civil Works In accommodation No. 5 Type-6 Situated As A Result Of Change Of Residence In Raj Bhavan Colony Under Renovation Improvement Help.- 1 Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead : Of area 3 sq. metres and below DAR NO-15.13.1 2 Brick work with common burnt clay (non madular) brick of class- 150 in superstructure above plinth level up to floor V level in all shape and sizes in cement mortar 1:4 ::(1 cement :4 coarse sand )( Dar 6.4.1) 3 Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. For thickness of tiles 10 mm to 25 mm DAR NO-15.23.1 4 Providing and fixing of kitchen shelves/cabinet with basket, shutter is made by mica laminated 18-19 mm board and back side of box is made by 6 mm Ply . Length and width of cabinet is 50 cm and depth/height of cabinet is 65cm including cost of all accessories such as handle, hinges, rolling channel, basket, catcher etc complete work. 5 Plain Basket 19x20x4 Rate-2268/1.18=1915.25 6 Plain Basket 19x20x6 Rate-2688/1.18=2261.02 7 Plain Basket 19x20x8 Rate-3120/1.18=2644.07 8 Providing and fixing of kitchen cubborad shutter is made by mica laminated 18-19 mm board and back side of box is made by 6 mm Ply . Length and width of cabinet is 30 cm and depth/height of cabinet is 60 cm including cost of all accessories such as handle, hinges, rolling channel, basket, catcher etc complete work. 9 Providing and fixing of wooden Almirah Box Work with mica laminated 19 mm ply board out side with one side decorative lamination . including cost of all acessories such as SS handle, hinges, lock, rolling channel etc complete work. 10 Providing and fixing of wooden Almirah Frame Work with mica laminated 19 mm ply board out side with one side decorative lamination . including cost of all acessories such as SS handle, hinges etc complete work.(As per attached drawing) 11 Providing and fixing SWR pipes as per 15:13592 110 mm dia for drain & sewer system with trenching , refilling & testing of joint complete including all fitting , labour and T&P etc . 12 Providing and fixing 25 mm dia chlorinated polyvinyl chloride (cpvp )pipes , having thermal stability for hot & cold water supply including the supply with clamps at 1.00m spacing . This includes jointing of pipe and fiting with one step salvent cement and testing of joints complete as per direction of Engineer in charge -Internal work - Exposed on wall (dar-18.7.3) 13 Providing and fixing chlorinated polyvinyl chloride (CPVC) pipes , having thermal stability for hot & cold water supply , including all CPVC plain & threaded fittings , i/c fixing the pipe with clamps at 1.00 m spacing . This includes jointing of pipe & fitting with one step CPVC solvent cement and cost of cutting chases and making good the same including testing of pipes complete as per direction of Engineer - in - charge , concealed work . including cutting chases and making good the walls etc (20 mm nominal outer dia pipe )18.8.2 14 Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sq.m including pointing the joints with white cement and matching pigments etc., complete.(dar-11.38) ( size of tile 300x300mm ) 15 Providing and fixing 1st quality ceramic, glazed wall tiles conforming to IS 15622 (thickness to be specified by the manufacturer) of approved make in all colours, shades except burgundy, bottle green black of any size as approved by Engineer-in-charge, in skirting, risers of steps and dados, over 12 mm thck bed of cmeent mortar 1:3 ( 1 cement 3 coarse sand) and jointing with grey cmeent slurry @ 3.3 kg per sqm, including pointign in white cement mixed with pigment of matching shade complete.DAR NO-8.31 16 Providing and placing on terrace (at all floor levels )polyethlene water storage tank . IS:12701 marked , with cover and suitable locking arrangement and making necessary holes or inlet , outlet and overflow pipes but without fitings and the base support for tank (Dar-18.48) 17 Providing and fixing C.P. brass ANGLE VALVE CODE -FLR-5053N Jaquar for basin mixer and geyser points of approved quality 15 mm nominal bore. 18 Providing and fixing C.P. brass wall mixture with tele phonic shower arrangement/bend (Jaquar make code FLR-5273UPR) or Equivalent quality. 19 Providing and fixing C.P. brass center hole basin mixture with long Casted Swinging Spout of Jaquar or Equivalent quality Make (Code FLR-5001B). 20 Providing and Fixing C.P. brass bib cock OPP-15037 PM Jaquar make with wall Flange Equivalent Quality conforming 21 Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete. DAR No-17.33 22 Providing and fixing C.P. Brass Two way bibcock heavy quality JAQUAR or Equivalent make including supply of all material, labour T&P etc. complete. 23 Supply and fixing C.P. Hand Shower (Health Faucet) with 8mm Dia 1.00 mtr. Long Flexible tube & wall hook Jaquar ALD-573 including supply of all material, labour T&P etc. complete. 24 Providing and fixing floor mounted, white vitreous china single piece, double traps syphonic water closet of approved brand/make, shape, size and pattern including integrated white vitreous china cistern of capacity 10 litre with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge DSR NO-17.81 25 Supply and fixing of white glazed earthen ware Wash Hand Basin with pedestal ( 550x430x195 mm Qubax ) with C.P Waste jali,, pvc waste pipe, including supply of all materials labour T&P etc. required for proper completion of the work. 26 Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality ) complete with 6 mm thick hard board ground fixed to wooden cleats with c.p brass screws and washers complete(dar-17.31) 27 Providing and fixing C.P. Soap Dish of jaquar make including supply of all material, labour T&P etc. complete. 28 Providing and fixing CP towel Rod OF JAQUAR Make Cat No- ACN-1111SM together with pair of CP brass brackets to fit the towel rail complete. 29 Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests DSR NO- 17.1.1 30 Providing and fixing wash basin with c.i brackets . 15 mm c.p brass pillar tapes , 32 c.p brass waste of standard pattern , including painting of fitting and cutting and making good the walls wherever requried:Stainless Steel AISI-304(18/8) Wash basin 530x345 mm with single 15 mm C.P. brass pillar tap DSR NO-17.7.11 31 Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. 15 mm nominal bore DAR NO-18.50.1 32 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15 mm nominal bore DAR NO-18.53.1 33 Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required::In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works. (10.25.2) 34 Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.0.63 mm thick with zinc coating not less than 275 gm/ m² DSR No-12.1.3 35 Providing and fixing false ceiling at all heights including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS: 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturers specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with:12.5 mm thick tapered edge gypsum moisture resistant board DSR NO-12.45.3 36 Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. DSR NO-13.88 37 12 MM cement plaster of mix ;1:4 ( 1 cement :4 coarse sand ) ) DAR NO-13.4.1 38 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.(D.S.R Item-13.80) 39 Finishing walls with Acrylic premium Smooth exterior paint with Silicon additives of required shade: New work ( Two or more coats applied @ 1.43ltr/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm) (apex Ultima, weather coat All guard) asian, berger. ( D.S.R Item 13.47.1 ) 40 Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade Old work ( Two or more coats applied @ 1.43 ltr/10sqm) over existing cement paint surface (apex Ultima, weather coat All guard).13.112.1 41 Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture 13.48.3 42 Provding and fixing ISI marked flush door shutters conforming to IS : 2202 (part-1) non- decorative type, core of block board contruction with frame of 1st class hard wood and well matched commercial 3 ply veneers on both faces of shutter :35 mm thick including isi marked stainless steelbutt hinges with necessary --9.21.1 43 Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws with ISI marked M.S. pressed butt hinges bright finished of required size econd class teak wood 9.27.2.1.1 44 Providing and fixing factory made uPVC glazed/wire mesh windows/doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367: Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge.Three track three panels sliding window with two glazed & we wire mesh panels with Aluminium channel for roller track, wool pile, nylon rollers with SS 304 body.Using R2 series with frame (70 mm & above) x (40 mm & above) & both glazed and fly screen sash (25 mm & above) x (50 mm & above) with zinc alloy (zamak) powder coated touch locks with hook. (Height upto 1.2 metre).9.147.A4.1 45 Providing & fixing float glass panes :(5.00 mm thick glass panes weight not less than kg/sqm ) dar - 9.7.2.2) 46 Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying:(a) after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm.(b) laying second layer of Fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm.(c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg/sam and coarse sand @ 1.289 kg/sqm, This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30 cm on parapet wall and tucked into groove in parapet all around.(d) fourth and final layer of brick tiling with cement mortar (which will be paid for separately.For the purpose of measurement the entire treated surface will be measured.DSR NO-22.6 47 Cement concrete flooring 1:2:4 (1 cement :2 coase sand :4 graded stone aggregate ) finished with a floating coat of neat cement , including cement ,slurry ,but excluding the cost of nosing of steps etc complete ,40 mm thick with 20 mm nominal in size stone aggregate (40 mm thick with 20 mm nominal in size stone aggregate ) DAR NO-11.3.1 48 Treatment of soil under exsting floors using chemical emulsion @ one liter per hole , 300mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1:2(1 cement:2 coarse sand ) to match the existing floor with chlopyriphos/ Lindane E.C 20 % with 1% concentration(dar-2.35.3) Please Enable Macros to View BoQ information
