Tender For Special Repair To Building No Cr/3 At Piru Singh Enclave Under Ge Panagarh; 2 M&L Brick work with fly ash bricks, straight or curved on plan exceeding 6 M mean radius built in cement mortar 1:6including demolition of old unserviceable brick work complete all as specified and directed. 3 M & L Brick work with fly ash bricks, straight or curved on plan to any radius in half brick thick built in Cement Mortar 1:4including demolition of old unserviceable brick work completeall as specified and directed. 4 Taking down cement plaster on brick or stone wall etc. including racking out joints hacking for key scrubbing down with water etc complete all as specified anddirected. 5 M & L rendering5mm thick cement plaster in cement mortar 1:3 on ceiling including finished even and smooth without using extra cement complete all as specified and directed. 6 M & L rendering15 mm thick cement plaster in cement mortar 1:6 on fair faces brick or concrete surfaces of wall including finished even and smooth without using extra cement complete all as specified and directed. 7 Supply only integral Liquid water proofing compoundcomplete all as specified and directed. 8 M & L preparation of new plastered surfaces of ceilings and applying three coats of white wash complete all as specified anddirected. 9 M&L two coats of Acrylic distemper over a coat of alkali resistant primeron newly plastered surfaces of walls,to achieve a level and smooth to wall, preparing wall with 1mm thick wall care putty to a uniform smooth surface before applying primer, of any description including preparation of surfaces all as specified and directed. 10 S&F Chimney bars (straight or camber); bearing bars; ton-gues or water bars for window frames; window guard bars, plain let in & fixed independently in wooden frames L or T section support for shelves etc., & similar articles conforming to Fe 290-0 Gde E-165 complete all as specified anddirected. 11 M & L preparation of new painted steel and iron surfaces of any description exc 10 cm width or girth and applying TWO coat of synthetic enamel paint over a coat of red oxide zinc chrome complete all as specified and directed. 12 M&L 100 mm thick PCC type B-1, (1:2:4) using 20mm graded stone aggregate as in receiving floor Finishes including demolition of old unserviceable PCC complete all as specified and directed. 13 M&L Non Skid ceramic tiles7 to 8mm thick (squares/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11sqm,in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 15mm thick Screed bedding layer in cement mortar 1:6 including dismentaling the old unserviceable tile work including backing plaster complete all as specified and directed. 14 M&L Non Skid ceramic tiles7 to 8mm thick (squares/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm,in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 15mm thick Screed bedding layer in cement mortar 1:6 including dismentaling the old unserviceable tile work including backing plaster complete all as specified and directed. 15 M&L Non Skid ceramic tiles7 to 8mm thick (squares/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm,in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 10mm thick rendering in cement mortar 1:4 including the old unserviceable tile work including backing plastercomplete all as specified and directed. 16 M&L Glazed ceramic coloured tiles in vertical surface 300X 450X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over & including 10mm thick rendering in cement mortar 1:4 including the old unserviceable tile work including backing plaster all complete all as specified and directed. 17 M&L Machine cut kota stone slab flooring 20 to 25mm thick over & including cement screed of 20mm thick cement mortar 1:6 laid & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & polishing including dismentaling the old unserviceable stone work complete all as specified and directed. 18 M&L Kota stone slab 20 to 25mm thick in riser of steps, skirting, dado & pillar over plaster of 10 mm thick in cement mortar 1:4& jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & polishing including dismentaling the old unserviceable stone work complete all as specified and directed. 19 M&L green Marble work 18 to 20 mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar(1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade of Makrana Adanga including dismentaling the old unserviceable stone work complete all as specified and as directed. 20 M&L20 to 25 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, including screed bed of 20mm thick in cement mortar 1:4 cement mortar, including dismentaling the old unserviceable stone work complete all as specified and as directed. 21 M&L Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations, complete all as specified and as directed. 22 M&L 75 mm thick Plain cement concrete 1:3:6 type C2(using 20 mm graded stone aggregate) finished the as in plinth protection surfaces, even and smooth without using extra cement, etc including dismentaling the old unserviceablePCC complete all as specified and directed.[Note: The rate includes the length not exceeding 3m length with joint to be filled with bituminous mastic filling comprising a mixture of 1 part of heated industrial bitumen 85/25 grade and two part of heated sand. The toe of plinth protection of size 75mm deep and 75mm wide shall also be of PCC M10] 23 Taking down chowkat or frames exc 1.5 sqm but n exc 4.0 sqm each with shutter (without taking off shutters from the frame) complete all as specified and directed. 24 Taking down Chowkats or frames not exc. 1.5 sq. m each with shutters (without taking off shutters from the frames) complete all as specified anddirected. 25 Taking Down shutter exc 2 sq. m each complete all as specified anddirected. 26 S&F factory made uPVC white colour Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) comprising of uPVC multichambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drillingof holes for fixing hardwares and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed. (Glass or wiremesh shall be paid separately) 27 Item Ser No. 1.025 contd.......[Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. all complete as per thedirections] 28 S&F Providing and fixing factory made uPVC white colour fixed window, area not exceeding 1.00sqm each made of extruded profiles with wall thickness of 2.3mm(+-0.2mm). Window profile with hollow section with multi chamber. Frame (60mm x 58mm). T profile (Onevertical length in between two shutters) (60mm x 74mm). Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc. making arrangement for fixing of hardware, EPDM gasket. 1.2 +–0.2mm thick, galvanized steel Frame (28mm x 21.5mm), T profile (27mm x 17 mrn) to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners- 5mm thick glazing with selected quality glass complete all as specified & directed.(Note: The unit rate quoted by contractor excludes costof glass and includes all other connected accessoriesNet opening will be measured for payment purpose.) 29 S&F Sheet glass 4 mm thick, ordinary quality & glazing with oil putty in square but n.exc 0.5 sq.m in each pane complete all as specified and directed. 30 S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed. 31 S&F Solid PVC door frame of size 50mm x 95mm made out of 5mm wood grain printed PVC sheet reinforced with M.S. tube, in opening as per specification & drawing complete all as specified and directed. 32 S&F Factory made solid moulded PVC door shutter 28 to 30mm thick (style) with 2,4 or 6 raised panel design with 2 mm thick 3D woodgrain moulded PVC sheet polyurathane painted on the front face & 2 mm thick plain colour PVC sheet on back face with particle face supply & fixing on frame, as per specification & drawing complete all as specified anddirected. 33 S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 50X100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardan and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.edepth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made complete all as specified anddirected. 34 S&F for Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 50X125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardan and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.edepth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made complete all as specified anddirected. 35 S&F Factory made single extruded WPC (Wood Polymer Composite) solid decorative panelled decorativeflush door shutter one side plain on other sideof 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: stainless steel butt hinges and necessary S S screws shall be paid separately) complete all as specified anddirected. 36 S&F factory made single extruded WPC (Wood Polymer Composite) wire gauzed i.e. panel shutter will bewire mesh in lieu WPC , the wire gauze shall be warped on additional square 8mm MS Solidtube and this tube shall bewelded to MS frame complete all as specified and directed. 37 S&F stainless steel Butt hinges 100mm size,extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, complete all as specified and as directed. 38 S&F stainless steel Butt hinges 75mm size, TYPE-C21 extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, complete all as specified and as directed. 39 S&F Aluminium alloy, anodised, sliding door bolt 300mm long with hasp, staple (bolt type) & fixing clips of sheet, cast or extruded sections & fixing bolts & sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed. 40 S&F extrudedAluminium alloy handles 150mm size, cast type, anodised complete all as specified anddirected. 41 S&F extrudedAluminium alloy handles 100 mm size, cast type, anodised complete all as specified anddirected. 42 S&F Aluminium, anodised, barrel tower bolts 150mm long of extruded section complete all as specified and directed. 43 S&F Aluminium, anodised, barrel tower bolts 75mm long of extruded section complete all as specified and directed. 44 S&F in repairs 150 mm long Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed. 45 S&F in repairs Hasp and staple, 75 mm long safety type, brass with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed. 46 Dismanting of wrought iron or mild steel work af any description not otherwise provided for complete all as specified and directed. 47 S&F in repairs 18 mm thick PVC sheet one side laminated, (density 600 kg/cum), fixed in kitchen cabinet and like, complete all as specified and directed. 48 M&LPVC lipping 0.45mm thick over PVC Sheet, fixed to PVC sheet with necessary fittings, complete all as specified and directed. 49 Cutting chases in brick walls, pinning in, making good to facings where required and pointing in cement mortar 1:3 and cutting chases for concealed water tubing and making good of groves for concealed GI tube, cutting not exc 10cm girth complete all as specified anddirected. 50 Supply & laying of CPVC pipes of 16 mm outer dia SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including taking up or down old unserviceable existing pipes complete all as specified anddirected. 51 Supply & laying of CPVC pipes of 20 mm outer dia SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floorsincluding taking up or down old unserviceable existing pipes complete all as specified and as directed. 52 S&F in repairs vitreous china squatting pan Orissa pattern size 580x440mm white with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap and to flushing system anti syphonage pipe etc complete all as specified and directed. 53 S&F in repairsPVC valveless,syphonic action type, low level PVC flushing cistren 10 ltr capacitywhite with flush pipe & all fittingcomplete all as specified & directed. 54 Supply & Fixing in repairs Vitreous China Ware Wash hand basin white flat back size 550mmx400mm without pedestal, cutting for and pinning ends of brackets or erecting stand including necessary PVC outlet pipe, CP coupling 32mm diacomplete all as specified complete all as specified & directed. 55 S&F in repairPVC connections 15 mm size with PTMT nuts of length 600mm complete all as specified anddirected. 56 S&F in repairs 32mm dia Waste coupling, brass , chromium plated for glazed ware , basins , etc. with long screwed shanks and fly -nuts , flange end bedded in red lead cement and other end fixed complete all as specified and directed. 57 S&F in repairs sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm etc, complete all as specified and directed. 58 S&Fin repair chromiuim platedSwivel shower roses with shower arm, 125 mm size including fxing to steel pipe or union etc complete all as specified and directed. 59 S&Fin repairs tubular towel rail 20 mm dia ‘D’ type 60 cm long between flanges ofbrass chromium plated including brackets. complete all as specified anddirected. 60 S&F in repairs Corner glass self assembly consisting of 5.5 mm thick glass sheet glass self 200mm with CP bracket gaurd and railing complete all as specified anddirected. 61 S&F in repairs waste coupling of 40mm dia brass chromium plated for glaze ware sinks, basins, etc with long screwed shanks and fly nuts flange and bedded in red lead cement and other end fixed complete all as specfied anddirected 62 S&Fin repair gratingdoom 125mm dia with waste hole of PTMT minimum weight 40 Gms complete all as specified and as directed. 63 S&F 110mm bore PVC (SWR) pipessingle socketed in any length with rubber ring joints fixed to wall/laid in floor including taking down old unserviceable pipes complete all as specified and directed. 64 S&F 75mm bore PVC (SWR) pipessingle socketed in any length with rubber ring joints fixed to wall/laid in floorincluding taking down old unserviceable pipescomplete all as specified and as directed. 65 S&F 110mm bore PVC (SWR) bends any radius complete all as specified and directed. 66 S&F 75mm bore PVC (SWR) bends any radius complete all as specified and directed. 67 S&F 110mm bore PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed. 68 S&F 75mm bore PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed. 69 S&F PVC door bends with oval access door (any radius) for 75 mm bore PVC pipes, complete all as specified and directed. 70 S&FPVC door bends with oval access door (any radius) for 110 mm bore PVC pipes, complete all as specified anddirected. 71 S&F 110mm dia PVC (SWR) junction, single (single T) equal or unequal with door access all as specified and directed. 72 S&Fin repairs fancy type C.P bib taps cast copper alloy with capston headed handles, screwed down screwed for iron pipe 15 mm bore or for brass ferrule complete fixed in repair complete all as specified and directed. 73 S&F in repairs Stop valve cast copper alloy screwed down high pressure with capston headed handle chromium plated concealed type screwed both ends for iron pipe 15 mm bore or for unions complete all as specified and directed. 74 S&F in repairs fancy type 15mm dia stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixedfor iron pipe fixed in repair complete all as specified and directed. 75 S&F in repairs Gun metal, globe or gate valve with iron wheel head, 20 mm bore,screwed both ends for iron pipe complete all as specified and directed. 76 S&F in repairs angle cock 15 mm bore fancy type chromium plated, with capstan head, high pressure, screwed down, screwed for iron pipe or for brass ferrule fixed to iron pipe complete all as specified and directed. 77 S&F in repairsPillar taps, fancy type 15mm borecast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered Hot or Cold with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified anddirected. 78 S&F in repairsvitrious china, box type toilet paper holderwith flat recessed type fixed with stainless steel screws complete all as specified and directed. 79 S&F in repair soap dish vitrious china, any type fixed to plugs chromium plated brass screws complete all as specified and directed. 80 M&L Providing and laying Water proofing treatment to sunken portion and adjoining walls of kitchen, WC, Bath & Toilet, etc all as specified anddirected in following stages complete all as specified & directed:Stage-I:Taking out old unservicable treatment over sunken floor and clean the surface with wire brush, dirt less with water jet etcStage-II:Providing and laying water proofing treament of sunken portions of WCs, bathrooms etc by applying cement slurry mixed with Acrylic based polymer modified cementorious composite compound coating of make as approved in Technical instruction 5/2023Stage-III:First layer of slurry of cement0.488kg/sqm mixed with acrylic based polymer modified cementious composite comppund @0.253kg/sqm . Tjhis layer will be alowed to air cure for 4 days.Stage-IV:Second layer of slurry of cement @0.242 kg/sqm mixed with acrylic based polymer modified cementious composite compound @0.126kg/.sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hrs. 81 M&L providing rust proof/anti corrosion treatment to bars all as mentioned below & all as specified & directed:-Stage-I:Cleaning of all exposed bars (new & old) around.Stage-II:Apply a single coat of rust proof/ anti corrosion treatment alround bars new & old as recommended by the manufacturer.[NOTE: Anti corrosive treatment shall be continuous especially in the regions where pitting, imperfections, etc were present on the surface of the bars. It is important that the rear portions of re bars (those towards the concrete substrate) should not be left without coating.] 82 M&L RCC (nominal mix), M-25 (using 20 mm graded aggregate) in slabs supported on walls, beams and columns, in roofs and in shelves and the like including demolition of old unserviceable RCC, complete all as specified and directed. 83 M&L RCC (nominal mix), M-25 (using 20 mm graded aggregate) in chajja including demolition of old unserviceable RCC, complete all as specified and directed. 84 M&L Formwork to sides of Chullah hoods, chajjas and similar items, for fair finished surface of concrete, all as specified and directed. 85 M&L Formwork to soffits of suspended slabs such as roof slabs, floorslabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping), for fair finished surface of concrete, all as specified and as directed. 86 M & L TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specified and directed. 87 M & L TMT bars6 to 8 mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips as in stirrups, spacers and binders complete all as specified and directed. 88 M&L Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; complete all as specified and directed. 89 M&L for wateer proofing treatment to roof as per following stages complete as as specified & directed:Stage-I:Taking down/dismentaling of old APP treatment, PCC padding rendering on roof & cleaning the surface throughly by jet watering & apply cement slurry on old surface.Stage-II:M&L40 mm thick plain cement concrete 1:2:4 type B-0 (using 12.5 mm graded crushed stone aggregate) as in roof padding, finished fair and even on roof surfaces.Stage-III:M&L rendering 5 mm thick on fair faces on roof surfaces of concrete surfaces in cement mortar 1:4, finished even and smooth without using extra cement including mixing of water proofing compound.[Note: WPC will be measured & paid separately] 90 Item Ser No.1.088 contd.......Stage-IV:M&L providing water proofing treatment with a layer of APP based polymeric membrane, 3 mm thick (minimum), weighing not less than 3.60 kg/Sqm reinforced with polymer non woven fabric (weighing not less than 160 gm/ Sqm) shall be applied over one coat of cold bituminious primer @ 0.40 ltr/ Sqm ( membrane shall be laid using butane torch and sealing all joints etc, complete all as specified and directed .( Note: The overlaps shall be of minimum 75 mm on longitudinal direction and 100 mm on transversedirection) complete.Stage-IV:M&Lone coat of aluminium paint over APP membrane, over roof. 91 S&F in repairs soft closing 4 hole full overlay O crank high grade mild steel, bright finish or electro galvanised for cup board cabinet shutter hinges Complete all as specified & directed. 92 S&F in repair magnetic catcher for kitchen cabinet shutter as approved Complete all as specified & directed. 93 S&Fin repairs C.P bib taps long body cast copper alloy with capston headed handles, screwed down screwed for iron pipe 15 mm bore or for brass ferrule complete fixed in repair complete all as specified and directed. 94 S & F in repairs wall mixer cromium plated 3 way including telephonic shower arrangement with connecting legs, wall flanges & wall bracket for hand shower all as specified & directed. 95 S&F in repair MS dropery rodpowdercoated 25mm internal dia in curtain rod, sample complete all as specified and directed. 96 S&F MS Powder coated bracket size 150 mm made to shape suitable for holding curtain/ dropery rod of 25 mm dia fixed with PVC rail plugs and MS screws for single/ double rods, complete all as specified and directed. 97 S&F in repair stainless steel kitchen plate rack(24x24x10) including necessary fixing/fitting & making good the existing surface complete all as specified and directed. 98 S&F in repairs Door seal (Snake guard) with Aluminium frame powder coated complete all specified & directed. 99 M&L repairs to crack portion with jacktting technuque, taking down existing plaster up to brick wall surface of min 200 mm wide, cleaning to loose particles on surface of brick work along the length of crack and filling the gap/crack area with PCC 1:1.5:3 type A0 using 12.5 mm aggregate up to brick surface and inserting the welded mesh of size 25 x 25x 2 mm dia along the crack on both side of the wall surface fixed with, drilling holes 10 mm dia on either side of the crack by means of drilling machine through out the full width of the wall @ 25 cm c/c and insert 8/10 mm dia rod in the drilled holes, welded with horizontal rod to with hold the welded mesh and applying grit plaster 1:1:2 using 4 mm and down aggregate finished even and smooth without using extra cement complete all as specified and directed.(Note: Reinforcement and welded mesh will be measured and paid separately ) 100 S&F in repair 600mmx450mm bevelled edge mirror of selected quality glass, mounted on,with chromium plated brass screws and cup washers, all as specified and directed. 101 S&F multipurpose lock 12mm to 25mm thick panel, for cupboard/ cabinet, with brass screws, brass keys fixed to cabinet/cupboard, complete all as specified and directed. 102 S&F100mm Brass Handle for cupboard/ cabinet, fixed with SS screws, complete all as specified and directed. 103 M&L Plain Cement concrete of Type C-1, 1:3:6 using (40 mm graded stone aggregate) in surface channels and drains, complete all as specified and directed. 104 S&F Ball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixed, complete all as specified anddirected. 105 S&F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165, complete all as specified anddirected. 106 Sch A Part-II: E/M Portion: 107 Taking down carefully aluminium/Copper conductor point wiring (light , fan, socket or powr) complete including fittings such as switches, ceiling rose, pendents, regulators sockets etc and removing (except those to be reused shall be kept in safe custody at the site) and making good disturbed surfaces of walls, floors etc tomatch with the existing completeall as specified and directed. 108 M&Lpoint wiring for light point/ fan point, one light/fan/exhaust fan point controlled by one, one wayswitch using1.5 sqmm nominal cross sectional areamultistrandedcopper conductor ,PVC insulated unsheathedFRLSH cables in and including 20 mm dia or higher size PVC concealed conduits and fittings of medium grade, including sheet metal modular box for suitable frame 2 to 8 module size and 1.5 sqmm nominal cross sectioanl area multistranded copper conductor FRLSHPVC insulated unsheathed earth wire and connecting to earth dolly andbrass screws, washers etc. complete all as specified and directed. 109 All as per item No.2.02 above but One 3 pin 5 Amps socket out let points with cable 2.5 sqmm on independent board complete all as specified & directed. 110 All as per item No.2.02 above but5 Amp socket on same boardwith other switches complete all as specified & directed. 111 Allas per ItemNo 2.02 mentionedhere-in- before but for onecalling bellpoint controlled by one one way Bell switches complete all as specified & directed.. 112 All as item No.2.02 above but one light point controlled by two 2 way switches, with cables 1.5 sqmm size complete all as specified & directed. 113 M&Lpoint wiring forPower point on Independent board controlled by one, one wayswitch using4 sqmm nominal cross sectional areamultistrandedcopper conductor ,PVC insulated unsheathedFRLSH cables in and including 20 mm dia or higher size PVC concealed conduits and fittings of medium grade, including sheet metal modular box for suitable feame 2 to 8 module size and 4 sqmm nominal cross sectioanl area multistranded copper conductor FRLSHPVC insulated unsheathed earth wire and connecting to earth dolly andbrass screws, washers etc. complete all as specified and directed. 114 S&F switch modular type 6 Amp one way, one module, single phase, complete all as specified and directed. 115 S&F socket outlet 5 Amps, 5 pin, modular type, 2 module , single phase complete all as specified anddirected (for same board) 116 S&F switch socket combination5 Amps, 5 pin, modular type, 3 module , single phase complete all as specified and directed (for Independent board) 117 S&F switch socket combination15/5 Amps,6 pin, modular type, 3 module , single phase complete allas specified and directed (for Independent board) 118 S&F switch modular type 16 Amp one way, one module, single phase, complete all as specified and directed. 119 S&F socket outlet 16 Amps, 5 pin, modular type, 2 module , single phase complete all as specified anddirected 120 S&F switch modular type 6 Amp two way, one module, single phase, complete all as specified and directed. 121 S&F bell push ,modular type 6 Amp SP one way, 1 module , complete all as specified and directed. 122 S&F fan regulator modular, five step, type 120 W 2 module suitable for 230 volt .cmplete all as specified and as directed. 123 S&F ceiling rose surface bakelite 65 mm x 50 mm two to three terminal suitable for 230 Volts AC 6 Amps complete all as specified & directed. 124 S&F lamp holder, PVC/polycarbomate type with back plate straoght of angle suitable for LED lamp complete all as specified and directed 125 S&FTurbo 9 watt inverter LEDlamp B22 9 watt of capacity 220 - 240 volts, 50 Hz complete all as specified and directed 126 S&F Buzzer, Ding dong, AC 230 Volts, single pole 230 volts all as specified and directed. 127 M&Lfor sub-main wiring with two run of FRLSH PVC insulated unshethed single core multi-stranded copper conductor of size 4 sqmm and one run of 2.5 sqmm copper conductoras continuityearth wiredrawn in and including PVC Conduit concealed of suitable size but not less than 20 mm dia on wall / floor etc, including PVC fittings such as bends Tee and boxes including taking down old unserviceable sub main wiring all as specified and directed(Note : (i) Two run of 4 sqmm cable,one run of 2.5 sqmm cable, one run of PVC conduitshall be measured and paid as one unit. 128 M&L for sub-main wiring with two run of FRLSH PVC insulated unshethed single core multi-stranded copper conductor of size 6 sqmm and one run of 4 sqmm copper conductoras continuityearth wiredrawn in and including PVC Conduit concealed of suitable size but not less than 20 mm dia on wall / floor etc, including PVC fittings such as bends Tee and boxes including taking down old unserviceable sub main wiring all as specified and directed [Note : (i) Two run of 6 sqmm cable,one run of 4 sqmm cable, one run of PVC conduitshall be measured and paid as one unit.] 129 S&F wall LED street/security light fittings 35 watt, 230 volts, AC outdoor type with high pressure die cast aluminium hosing and eat resistant comlet with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protectioncomplete allas specified and directed. 130 S&F LED light fitting 1 x 20 watt 4 long surface mounting ultra slim LED batten in extruded PC housing and square shaped diffuserconnecting up with complete all accessories andconnection from ceiling rose with twin core twisted flexible copper conductor cable withsuitable size and earthing complete all as specified and directed. 131 S&F wall mounted Decorative wall light fixture made up of Polycarbonate, suitable for 9 Wretrofit LED Lamp B22 base with 9W LED bulb complete all as specified and directed. 132 S & F LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified & directed. 133 S&F round shape 12 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified & directed. 134 S&FLED light fitting 1 x 10 watt 2 long mirror light surface mounting ultra slim LED batten in extruded PC housing and square shaped diffuserconnecting up with complete all accessories andconnection from ceiling rose with twin core twisted flexible copper conductor cable withsuitable size and earthing complete all as specified and directed.[Make: Havells/Crompton/Jaquar or any similar make as mentioned in Particular specification] 135 S&Fventilating PVC body exhaust fan250 mm sweep 230 volt AC,minimum air flow capacity 800-860 cubic meter per hour, speed 1200-1350Rpm high efficency complete with louver and all accessories including cutting hole or square shape of suitable size, making good surface by doing plaster and applying two coat of distemper complete with fixing arrangement to wall connected with twin core twisted flexible copper conductorof suitable size including taking down and submit to store yard complete all as specified and directed. 136 S&Fventilating PVC body exhaust fan150 mm sweep 230 volt AC, minimum air flow capacity 275 Cum/ hour, speed 1650-1750Rpm ,minimum 2 year warranty complete with louver and all accessories including cutting hole or square shape of suitable size, making good surface by doing plaster and applying two coat of distemper complete with fixing arrangement to wall connected with twin core twisted flexible copper conductorof suitable size all as directed. 137 S&F epoxy powder coated sheet metal enclosure for TPN DBs, 4 ways, double door with mounting fitted with bus bar, DIN channel , neutral link and incoming contact, IP-43 complete all as specified &directed. 138 S&F epoxy powder coated sheet metal enclosure for DBs, double door, Single pole and neutral, 12 ways,with mounting fitted with 200 Amps rated bus bar, DIN channel , neutral link and incoming contact complete all as directed. 139 S&F MCB 4 pole, 415 volts fixed type 40 to 100Amps,C Curve with breaking capacity 10 kA complete including necessry connectionall as specified and directed. 140 S&FMCB SPN 32 Amps,C curve 10kA, 240 Volts and to be housed in DBscomplete including necessry connectionall as specified and directed. 141 S&FMCB SPN 40 to 63 AMP,C curve 10kA, 240 Volts and to be housed in DBscomplete including necessry connectionall as specified and directed. 142 S&FMCB SP 6-32 Amps,C curve 10kA, 240 Volts and to be housed in DBscomplete including necessry connectionall as specified and directed. 143 M&L for earthing complete with galvanised mild steel earth plate electrode 600x600x6.0mm thick, burried directly in ground to a depth not less than 2.25 metres deep below ground level with top edge of earth plate not less than 1.5 metre below normal ground level surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15 cm all around the plate, using GI wire 4 mm dia as earth strip electrode bolted or rivetted to earth plate at one end and connected to equipments at another end, GI earth strip encased inand including 40 mm dia GI lightgrade pipe from upper end of earth plate upto equipments,20 dia bore GI pipe light grade as water pipe from earth chamber to upper edge of earth plate, Test point , GI funnel with wire mesh fixed on water pipe andPCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in pit chamber and RCC pit cover 50mm thick precast RCC 1:2:4 type B-1, duly reinforced with MS round bars 6mm dia @ 100 c/c both ways with 10mm dia MS round bar as in lifting handles, excavation, earth work including laying the GI pipe concealed in floor/wall all as describedin electric plate No.3 of SSR Part I completeall as specified and directed and testing on completion. 144 S&Fceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) afterincluding taking down old Unserviceable fan and submit to store yard complete all as specified and directed. 145 S&Felectric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre,5 Star rated complete with all accessories such as safety valve, thermostate,NRV, connection piece etc including old unserviceable water heater & deposit to store yardcomplete all as specified and directed. 146 Making 02 Nos of holes on wall suitable for fixing of 40mm dia GI pipe to hanging ceiling fans including making good the existing surface and two coat distemper complete all as specified and directed. 147 S&F Tubes,medium grade,galvanised 40mm, with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed. 148 Labour for cutting holes (round type/square shape) suitable for exhaust fan 300 mm sweep andincluding making good all disturbed surfaces to match the existing positon and two coat colour distemper complete all as specified and directed. 149 Excavation in trenches, not exceeding 1.5 m wide and not exceeding 1.5 m in depth for laying of cables, pipes etc. and getting outincluding trimming the sides and forming bottom surfaces to required levels in soft/loose soilcomplete all as specified and directed. 150 Returning, filling in, including spreading, levelling, and well ramming in layer not exceeding 25 cm thick in soft/loose soil complete all as specified and directed. 151 Removing excavated material (soil) to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed. 152 S&F Pipes galvanized, 25 mm bore “Mediumgrade”, supplied and fixed complete to walls and ceilings or laid in floors complete including necessary fittings such as tees, bends, elbows, sockets, reducers etc as per site requirement including dismantaling/Taking down of old unserviceable pipes complete all asspecified and as directed. 153 Refixing old steel tubing including cleaning and connections in new or old position (in trenches, on wall/ceiling & floors etc) of 25 mm bore GI pipe including dismantaling/Taking down of old unserviceable pipes complete all as specified and directed . 154 S&Fgun metal ,gate valve, 25 mm dia with iron wheel head, screwed both ends for iron pipe and fix complete all as specified and directed. 155 S&F500 Ltrs rotational moulded polyethylene water storage tanks (Cylindrical, vertical with closed top) multi layered (minimum 3 layered), antivirius, antibacterial, anti fungus, anti algae threaded lid with UV Proctection confirming to relevent IS complete including provision of all inlet outlet overflow and drain pipe fittingincluding taking downunserviceable tank complete all as specified and directed. 156 Supply and fixing of high pressure PTMT float valve with epoxy coated alluminium rod and high density polythelene ball screwed for iron pipe 20 mm dia with fly nut complete all as specified anddirected. 157 Supply, laying, connecting, testing and commissioning of LT under ground cable XLPE insulated, armouredheavy duty electric cablewith aluminium conductor , 1100 vlts grade , cross sectional area 35 sqmm 3.5 core including taking out in trenchesincluding taking down old unserviceable LT Cable complete all as specified and directed.[Note:- (i)Excavation,sand cushioning,brick will be measured and paid separtely.] 158 M&L for river sand, washed dirtless and screened dry for cushioning to under ground cable in trenches below and around under ground cable including spreading and levelling complete as specified and directed .[Note :- Punned thickness of 18 cm shall only be considered for payment] 159 Supply and lay in trenches fly ash bricks, for cable protection all as specified and directed. 160 S&F Pipes galvanized,50 mm bore “light grade”, supplied and laid complete including necessary fittings such as tees, bends, elbows, sockets, reducers etc as per site requirement complete all as specified & directed. 161 S&F Galvanised Iron pipe 50mm Bore (dia) Light Grade for protection of UG cable laid in floors/Road Crossong ,complete all as specified and directed. 162 Labour only for horizontal boringby horizontal boring mahine for passing protection pipe up to 80mm Bore(dia) under road/foot path not exc 10 mtr in a single lenth complete all as specified and directed.[Note : pipe to be measure saparately.] 163 Supply & Laying double wall corugate, high density poly ethylene pipes (DWC HDPE) for LT Cable protection double wall corrugated (inner wavy 450N compression rating(light duty) conform to IS:16205(Part 24) Size of 63mm complete all as specified and directed.
