Tender For Turnkey Works For Setting Up Of Amrit Pharmacy At Uttar Pradesh University Of Medical Sciences, Saifai, Etawah, Up; 1 CIVIL WORKS 2 Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix) 3 Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil. 4 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. 5 Filling with contractors own earth ( excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m as per direction of site Engineer-in-charge 6 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size). 7 Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) 8 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:4 (1 cement : 4 coarse sand) 9 Reinforced cement concrete work in column, beams, suspended floors, roofs, having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand (Zone III) : 3 graded stone aggregate 20 mm nominal size). 10 Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto floor V level including plinth. Thermo - Mechanically Treated bars of grade Fe-500D or more 11 Centering and shuttering including strutting, propping etc. and removal of form for all heights: 12 Foundations, footings, bases of columns, etc. for massconcrete 13 Lintels, beams, plinth beams, girders, bressumers and cantilevers 14 Columns, Pillars, Piers, Abutments, Posts and Struts 15 Suspended floors, roofs, landings, balconies and accessplatform 16 Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. 17 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand) 18 Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. 19 Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface: Water thinnable cement primer 20 Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade:New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) 21 Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile including applying additional coats wherever required to achieve even shade and colour. Two coats 22 Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work 23 Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer and two or more coats of Enamel Paint all complete. 24 Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin- charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 25 Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).Kiln seasoned and chemically treated hollock wood 26 Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws 27 Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :300x10 mm 28 Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete. 29 Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete. 30 Providing and fixing bright finished brass handles with screws etc. complete: 125 mm 31 Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete. 32 Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double action hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-incharge (Door handle, lock and stopper etc.to be paid separately). 33 Providing and fixing of frameless glass door SS Patch Lock with out handle in toughened glassincluding all necessary screws etc. complete. 34 Providing and fixing both side 2 nos SS H handle having min 450 mm length in toughed glass door including all necessary screws etc. complete. 35 Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) including skirting with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades,laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc.,complete:Size of Tile 600x600 mm 36 Providing and fixing 12 mm thick frameless toughened glass partition of approved brand and manufacture, including top & bottom fixing arrangement counter opening and making necessary holes etc. for fixing required fittings, all complete as per direction of Engineer-in-charge 37 Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main T runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross T of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main T at 600 mm center to center to form a grid of 1200x600 mm and secondary cross T of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main T runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge.12.5 mm thick square edge PVC Laminated Gypsum Tile of size 595x595 mm, made of Gypsum plasterboard, manufactured from natural gypsum as per IS 2095 part I and laminated with white 0.16mm thick fire retardant PVC film on the face side and 12micron metalized polyester on the back side with all edges sealed with the face side PVC film which goes around and wraps the edges and is bonded to the edges and the back side metalized polyester film so as to make the tile a completely sealed unit. 38 ACP : Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding over Aluminium rectangular tube of minimum size 50x25x2mm, with open grooves for linear as well as curvilinear portions of the building, for all heights and all levels etc. including: a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metallic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc. c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing. The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics including all required & complete , as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in Sqm. up to two decimal places. 39 Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters.80x0.90 mm M.S. laths with 0.90 mm thick top cover 40 Providing and fixing ball bearing for rolling shutters. 41 Extra for providing mechanical device chain and crank operation for operating rolling shutters.Exceeding 10.00 sqm and upto 16.80 sqm in the area 42 Providing and applying fibre reinforced elastomeric liquid water proofing membrane with resilient acrylic polymers having Sun Reflectivity Index (SRI) of 105 on top of concrete roof in three coats @10.76 litre/ 10 sqm. One coat of self-priming of elastomeric waterproofing liquid (dilution with water in the ratio of 3:1) and two coats of undiluted elastomeric waterproofing liquid (dry film thickness of complete application/system not less than 500 microns). The operation shall be carried out after scrapping and properly cleaning the surface to remove loose particles with wire brushes, complete in all respect as per the direction of Engineer-in-Charge. 43 12 mm cement plaster finished with a floating coat of neat cement ofmix :1:3 (1 cement: 3 fine sand) 44 Furniture Works 45 Double Level Counter:Providing and fixing Double Level Counter, first step at 750 mm from ground, 900mm wide and Counter top at 1100 mm level and 300 mm wide. 12mm thick acrylic sheet (pure white in colour) to be used for counter top on 25 mm thick prelaminated commercial ply. Display unit with 8mm thick toughened glass fascia and 18mm thick prelaminated shelves to be in built in counter with movable shutter. Counter should contain retractable keyboard trays and partitioned drawers with drawer channel, cupboard units with swing door and auto close hinges. Drawers and cupboard are to be fixed with individual locks and handles. Cable manager and leg space are also to be provided.150mm high SS glossy skirting all Complete as per the design and instructions of engineer in charge. 12mm thick toughened glass partition to be provided above counter up-to roof height with necessary counter opening. Note: Only front elevation of wooden counter will be measured. (12mm thick toughened glass will be paid separately). Make laminate: GREENLAM, MARINO or equivalent. 46 Counter Height Stools :Supply and installation at site counter height stools of following specifications :Revolving adjustable Chrome plated steel body chairs with resistance to the corrosion.Cushion Seat with Lift mechanism for Adjustment of height. Minimum height 750mm before expansion. Medium Back rest and arm rest. Item shall be of reputed make. 47 Table: Supply and errection of Working Table 900mm length X600mm depth X750mm height made with 18mm thick prelaminated particle board with one side decorative and other side balancing lamination and all edges to be fixed with matching PVC edge beeding. Partitioned storage unit having swing door ,Partitioned cash drawer, Key board drawer and leg spaceare also to be provided with individual locks and handles, autoclose hinges, drawer channels etc. complete as per the aproved design andinstructions of engineer in charge. 48 Chair: Supply and errection of Medium back ergonomic chair with five nos. Star shaped Nylon base. Castors: 50mm diameter nylon twin wheel, gas lift height adjustment, back angle adjustment and backrest height adjustment. Fixed armrest providing natural resting for arms. Seat with PU cutted foam backed fabric, back rest with mesh type fabric. Upholstery: Heavy duty rubber backed fabric in BLACK. 49 Medicine display shelf: Providing and fixing of Open Wooden display laminated cabinets of length 900mmX height 2500mm made up of Pre-laminated MDF Board, exterior Grade-I 18 mm thick confirming to IS: 14587 with decorative lamination on both side with proper provision of racks and shelves.Bottom storage unit of 600mm deep storage shall be 750mm from the ground with display wooden shelves @150mm C/c. Upper storage unit provided with display wooden shelves @150mm C/c and 450 mm deep and height of 1750mm from the bottom storage unit. All the edges to be finished with edge band and shelves to be fixed with proper bracket holders complete as per approved layout, drawings and instruction of Engineer in Charge. Note: Only front elevation will be measured. 50 Over Head Storage Cabinet: Providing and fixing ofOver head storage cabinet ofdimension 900mmX600mmX450mm made up of Pre-laminated MDF Board, exterior Grade-I 18 mm thick confirming to IS:14587 with decorative lamination on both side including inside middle partitions and with sliding door on front side with rollers, sliding channels, handles, locks etc. All the edges to be finished with edge band and shelves to be fix with proper bracket holders complete as per approved layout, drawings and instruction of Engineer In Charge. Note: Only front elevation will be measured. 51 Slotted Angle Racks : Supply and errection of Powder coated slotted angle metalic rack having min 6 shelfs made up ofmin 40 X 40 X 2 mm size rolled steel angle posts shall have 8-mm diameter holes provided at 50-mm centre to centre.Metal shelves shall be made from mild steel sheets not less than 1.0 mm in thickness and with sufficient stiffners. Shelves shall have lipped flangeswidth of flange being 30 mm and depth of lip 15 mm .Min size of rack 900mm Length X 400mm Depth X 2000mm Height. 52 Airport Chair, 3 Seater: Supply and erection of Airport Chair (Set Of 3 In 1) having overall dimension ofLength 1720mm x width 675mm x height 850mm. Chair dimension floor to seat height 400mm and floor to arms height 600mm seat and back frame size Length 495mm x width 490mm x height 550 mm. Chair arms is made up of Stainless Steel Tube 50mm X 25mm Oval Shapes Tube 1.6mm thickness. Legs are made to 48mm Stainless Steel round Tube 2mm thickness and seat and back frame made to 19mm Stainless steel round tube 1.2mm thickness. Seat and back use to 1.2mm thickness perforated Stainless steel sheet. All the end cups are made to stainless steel glossy finish cups and using for the floor levellers 10mm nylon adjustable bush. 53 DISPLAY WORKS 54 Backlit Acrilic Board with projected channel letters: Supply, installation, testing and commissioningof weatherproof backlit acrilic board with projected channel letters made upof 20mm thick acrilic board and having box depth of min 100mm in approved size and design with reqired LED strips for high glow light. The board shall be fabricated and fixed over suitable welded and painted 25X25X3mm MS angle frame in suitable location and in proper line and level with all necessary fastners, supports etc. Electrical works likes electrical wirings, connections, fittings, externaly fixed weather proof 2/3 pin plug points and sockets including boxes etc. to be complete properly. All fabrication and fixing should be done as per approved design and instructions of Engineerin Charge. (Note: Only front elevation will be measured.) 55 Vinyl TransparentVision Glass Stickers: Supply and pasting of Vinyl Transparent Vision Glass Stickers in approved size and design in glass partition and door as per the instruction of Engineer in Charge. 56 PVC flex board: Supply and fixing of PVC flex board in approved size and design including all the required steel frames and fixings as per the instruction of Engineer in Charge. 57 Providing & sticking/pasting of printed vinyl wall stickersas per approved size anddesign at all heights includes all the required as per the instruction of Engineer in Charge. 58 CAPITAL/SUPPLY ITEMS 59 Supply,Installation,testingandCommissioning of Desktop computers with following specification. Processor:12th or Higher Gen Intel® Core™ i5 - (30 MB cache, 16 cores) Memory:16 GB: 2 x 8 GB, DDR5 Video Card: Intel® Graphics Storage:1 TB, M.2 2230, PCIe NVMe, SSD, Class 35 OS: Windows 10/11 Pro English Chassis:Mini Tower, Wired Multimedia Keyboard and Mouse Integrated Wireless LAN Integrated Gigabit LAN Monitor 21.5 LED or higher. Make : Dell / HP or equivalent 60 SITC of All in One PC Client PC Configuration, BRAND (DELL/HP)12th Gen Intel® Core™ i3-12400 (18 MB cache, 4 cores, 8 threads, 2.5 GHz to 4.5 GHz Turbo), memory *8 GB: 1 x 8 GB, DDR5, Storage:512 GB, M.2 2230, PCIe NVMe, SSD, Class 35, OS: Windows 11 Pro English, Multimedia Wired Keyboard, Optical Mouse, 2 USB 3.2 Gen 1 ports, Integrated Wireless LAN, Monitor 21.5 LED or higher. 61 LaserjetMultifunctionalMonochromeNetwork Printer: Supply and Installation at site, All in One LaserjetMultifunctionMonochromePrinter havingLCDDisplay,withfunctionstocopy, print and scan, print resolution 600 dpi x 600 dpi, 20ppmprintspeed,Dutycycleminimum8000 pages per month, 24 bit depth, USB, Wi-Fi connectivity.Make:hp/brother/canon/epsonor equivalent, for Bill Printing cum Office use with Warrantyperiodofoneyear.Connectivity:Hi- speedUSB 3.0Supported,Wi-Fi,Media Types: Paper, envelopes, labels, cardstock, transparencies, postcards, Functionality: Print, Scan/Copy.Power Consumption:Maximum 250 WattsRecommended Make : hp/brother/canon/epson or equivalent 62 Laserjet Monochrome Network Printer : Supplyand Installation at site, Laserjet MonochromePrinterhavingLCDDisplay,with functions to copy and print, printresolution 600 dpix600dpi,20ppmprintspeed,Dutycycle minimum8000pagespermonth,24bitdepth, USB,Wi-Ficonnectivity.Make: hp/brother/canon/epson or equivalent 63 Visi Cooler / Pharmacy refrigerator : Supply, errection and commisioning of lab / pharmacyrefrigiratorasperfollowing specifications:UprightShowcase Coolers/refrigerators with Single Glass Door and Lock having 350-450 Litre capacity, Temperature range capability 1-10 degree celsius with Digital TemperatureControllerandDisplay,Minimum of 4 adjustable Shelves/Racks Recommended Make:CELFROST,BLUESTAR,VOLTAS, THERMO FISCHER 64 Cash Counting Machine cum Fake Note Detector Make : Optimus-Model No.OLC 04 or equivalent 65 CashSafe(Coffer)Volume.14LMin WallThickness: 2.5 mm min for body and 5 mm min for door Recommended Make: Godrej make, ModelNo.PremiumCofferBRN(ltemCode: SEBP1112) or equivalent (only manual lockinq system) 66 CounterCommunicationSystem:Supply, installation, testing and commisioning of two way countercommunicationsystemincluding speaker,mike,controlunit,powerunitetcall required (make : Ahujaccs 2300 or equivalent) 67 WaterDispenser:Supplyanderrectionofwater dispensercanhold20litrewaterbottlehaving normalstanding designwith14liter refrigerator atbottom andhaving3temperaturetapshot, plain and cold. 3 liter cooling and 5 liter heating capacity per hour. Body made of ABS plastic and tankmadeofFoodgradestainlesssteel.Heavy duty bottle piercer with bottle holder. withmin 1 year warranty. (Make : voltas / Blue star/ equivalent) 68 Supply of ABC Type fire extinguisher of 2 Kgs. Make SAFEX / MINIMAX / CEASEFIRE or equivalent 69 Electrical Work 70 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.Group C 71 Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. (Recommended Material : Polycab, RR Kabel, V Guard, Havells) 72 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.( Recommended Material : RR Kabel/National/ Ralison/RKG/ Finolex / Polycab / Havells) 73 2 x1.5 sq.mm + 1x 1.5 sq. Mm earth wire 74 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire 75 2 X 6 sq. mm + 1 X 6 sq. mm earth wire meter 76 Supplying and fixing 3 pin 5 A ceiling rose on the exising junction box / wooden block including connections as required. 77 S/F light plug point modular type accessaries : Supplying and fixing suitable size GI box with modular plate and cover in fronton surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection, painting etc as required, 78 S/F Power plug point with modular type switch : Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 15/16 and 15/16 amps modular switch, connection,painting etc as required. 79 S/F 20A SPN MCB industrial socket outlet : Supplying and fixing 20 A, 240 V, SPN Industrial type socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 A, “C” curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required. 80 Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)4 way (4 + 12), Double door 81 Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator):12 way, Double door. 82 S/F C series, MCB : Supplyingand fixing5 amps to 32 amps rating, 240/415volts, C curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections,testing and commissioningetc. as required. 83 Single pole 84 Single pole and neutral 85 Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 A 86 Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured copper power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required. 4 core 16 sq mm with factory made clamp including cable termination 87 Supply, Installation, testing & commissioning of branded best qualityThree phaseelectronic type energy meter with LCD display with battery back up.withall connections complete, Make:L&T or Equivalent . 88 S/F C series, MCB : Supplyingand fixing5 amps to 32 amps rating, 240/415volts, C curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections,testing and commissioningetc. as required. Triple pole 89 Supplying and fixing following rating, four pole, (three phase and neutral), 415 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63A 90 Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63 amps 91 Supply,installation,testingandcommissioningofthe following types oflight fittings with all accessorieson false ceiling, true ceiling or wall as directedand giving connectionswith 16/0.20 mm 3 core PVC insulated andsheathedroundcopperconductorflexwireor extendingthe original wiring and giving connectionsas required. All recessed type fixtures are to be supportedindependentlywith chains or GI wire anchoredto the ceiling with anchoring bolt of necessary size. All loose wires above the false ceiling are to be neatly concealed by flexible metal/pvc conduits.( cost to include lamps & all consumables also) 92 Supply and installtion of 30-36W, 230V, 4300 lumen, Recessed Square LED Cool White light fixture of dimession 600mm X 600mm on false ceiling along with all accessories with intergrated driver THD<10% and connections as well as making good the damages as required at site Engineer. Recommended makes: Philips/Crompton/Wipro or equivalent. 93 Supply and installtion of LEDtubelight of6000K and 20-24W on wall or ceiling as directedand giving connections as required.All loose wires are to be neatly concealed. (Make: Philips, Wipro, Crompton or equivalent) 94 Supply and installtion of 10-15W, 230V, Recessed Square or Round LED Cool White light fixture on false ceilling along with all accessories with intergrated driver THD<10% and connections as well as making good the damages as required at site Engineer. Recommended makes: Philips/Havells/Wipro or equivalent. 95 Supply, Installation, testing and commissioning of wall mount fan (400mm sweep), adjustable speed. min 60 degree oscillation, swing, Adjustable upward and downward tilt mechanism, Protective Guard, Including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable, mounting accessories, etc. as required. It shall be double ball bearning type. (Make: USHA, Cromption ,Havells) 96 Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required. 97 Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing as required. 98 Network / LAN 99 S/F Modular boxes, base & cover plate : Supplying and fixing 1 or 2 module ( 75 mm x 75 mm), GI box along with modular base, cover plate for modular switches in recess etc as required. 100 Providing and Fixing of RJ-45 socket outlet in the existing modular box with connections and all required. 101 16Port Network Switch :Supply, Installation, testing and commissioning of: 10/100 Mbps 16-Ports Gigabit Switch . ( Make : D-Link DGS-1008A) 102 Supplying,drawing and crimping with all accessories of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required.1 run of cable from Port Switch to Data socket 103 Supply, installation, testing and commissioning of best quality cat-6 patch cord having1 metre length complete as per specifications as required. 104 Supply, installation and commissioning of powder coated DVR 4U Wall Mounted ServerRack ofISO Standard of size 550 x 350 x 140 mmhaving depth adjustable mounting slots, top and bottom Panel with ventilation and cable entry facility, provision to mount the cooling fans on the top panel, lock and key etc. and having capacity to carry a max Load of 60 kg all complete as per the manufacturer specifications and instructions of Engineer In Charge. 105 CCTV 106 Supply, Installation, Testing & Commissioning ofIndoor IR Dome night vision cameras :2.0 MP, 0.1 lux, Resolution 720 P ,AWB/ BLC/ AGC,min 20m range, Built-in IR illumination, white color case, PAL-CE/FCC approved. Make: CP PLUS/HIKVISION/Honeywell or equivalent 107 Supply, Installation, Testing & Commissioning of Outdoor IR Bullet night vision camera :2.0 MP,0.1 lux, Resolution 720 P,AWB/ BLC/ AGC ,min 20m range, Built-in IR illumination, white color case, DC12V, PAL-CE/FCC approved. Make: CP PLUS/HIKVISION/Honeywell or equivalent 108 Supply ,Installation ,Testing & commissioning of SMPS Power supply unit for above camera as speficied by camera manufacturer -12VDC 10A 109 Supply ,Installation ,Testing & commissioning of Digital Video Recorder : 8-Channel Embedded HD DVR, 400fps, Real-time, with 2 TB HDD and English OSD, 230VAC. Rate shall be inclusive of all accessories, termination of cables, etc complete. 110 Supply ,Installation ,Testing & commissioning of 15 to 16LED Color Monitor. make :LG / Samsung/ Equivalent. 111 Supply and Laying ofCoaxial cable 2+1 RG59/RG6 premium quality CCTV power and video cable with ISI marked PVC conduit including terminations with suitable BNC Connector, power Jack etc complete. 112 AC 113 Inverter Air Conditioner: Supply, installation, testing and commissioning of Air Cooled Cassette Air Conditioner of following capacity consisting of indoor room unit with cordless remote control and one number outdoor condensing unit comprising of enegy efficient suitable rotary compressorfor operation on single phase, 230 V, 50Hz supply, fixing the outdoor unit on a raised platform as per manufacturers recommendation and fixing of room unit on ceiling, standard 3 m distance refrigerant copper piping with 13mm nitrile rubber insulation, providing and making interconnection between room& condenser as per site conditions, comprising of 1 or 2 dia drain PVC pipe with insulation 3m, canvas connections, full electrical cabling from power plug near indoor unit and to outdoor unit, ODU MS stand, first charge refrigarant gas, suitable stabilizer etc complete as required. ( Make : Voltas , Blue Star, LG, Samsung, Carrier,Hitachi ) :Minimum 3TR 3 star rated as per BEE 114 Supply and Installation of additional copper piping, cabling and drain piping for air conditioning unit with proper insulation including all required on wall/above false ceiling complete
