Tender For Comprehensive Maintenance Of B/R Services In Certain Buildings At Anupgarh Under Ge (Af) Suratgarh.; COMPREHENSIVE MAINT OF B/R SERVICES IN CERTAIN BLDGS AT ANUPGARH UNDER GE (AF) SURATGARH) 2 Demolition of brick work in any position, built in cement mortar complete all as specified and directed. 3 Demolition of cement concrete (un-reinforced ) of any description in ground floors and paving not exceeding 15 cm thick (below or above the ground level) and removing rubbish from the site.complete all as specified and directed. 4 Dismantling of floor, hearth or wall tilingand Stone floor including cement mortar bedding (but not backing) & removing and rubbish from the premises.Complete all as specified and directed. 5 Demolition of RCC any description in any position not otherwise specially provided for (reinforcement cut as required to facilitate demolition) and removing rubbish from the premises. 6 M&L 75mm cement concrete (1:3:6) Type C2 , 40 mm stone graded agg as in plinth protection, finished even and smooth w/o using extra cement. Complete all as specified and directed 7 M&L for RCC type B0 1:2:4(12.5 mm graded stone aggregate) as in Chajjasall as specified and directed by engr-in-Charge 8 Taking down cement plaster of any description including racking out joints, hacking for keys , scrubing down with water and removing rubbish from the site etc complete all as specified and directed. 9 Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specified and as directed 10 M&L for cement concrete 1:2:4 type B0(12.50 mm graded aggregates) filling in cracks, holes, chases by making surface even. Complete all as specified and as directed 11 M&L for Brickwork with subclass B bricks, straight or curved on plan exc.6m mean radius old size bricks in CM 1:6 complete all as specified and directed 12 M&L for 5 mm thick , plaster in cement mortar (1:3) on surfaces of ceilingand finishing the surface even and smooth without using extra cement all as specified & directed by Engineer-in-charge. 13 M & L for Rendering 15 mm thick on fair faces of brick or concrete surfacein cement mortar 1:4, finished even and smooth without using extra cement using WPC. complete all as specified and directed. (WPC shall be measured and paid for seperately). 14 M&L for rough cast plaster with a mixture consisting of crushed stone or fine gravel aggregate of size 6mm to 8mm as directed, mixed with coarse sand, fine sand and cement in the ratio of 1:1:1, finished even rendereing with under coat 15mm thick cement and sand mortar 1:3 complete all as specified and directed 15 M&L, Rendering 10 mm thick cement plaster in Cm (1:6) on fair faces of brick works or concrete surfaces , finished even and smooth w/o using extra cement, complete all as specified and directed. 16 Supply only Integral waterproofing compound.complete all as specified and directed 17 M&L for applying two coats of oil bound distemper over a coat of primer over surfaces including preparation of new surfaces finished even and smooth using 2 mm thickwall care putty complete all as specified & directed by Engineer-in- Charge. 18 M&L for Applying two coats of exterior acrylic emulsion in camouflaging pattern, over newly plastered surfaces over a coat of primer , including preparation of surfaces , complete all as specified and directed by Engineer-in-Charge. 19 M&L for preparation of newly plastered surfaces of ceiling and applying three coats of white wash all as specified & directed by Engineer-in- Charge. 20 M&L for non skid ceramic coloured tiles of 7 to 8mm thick, (square/rectangular) area of each tiles exceeding 0.11 Sqm but not exceeding 0.18 Sqm as infloors etc set & jointed in neat cementslurry and pointed in white or coloured cementto match the colour of tiles over and including screed bed or bedding layer of 15mm thick in CM (1:6) complete all as specified & directed by Engineer-in-charge. 21 M&L for Vitrified ceramic tiles 9 to 10 mm thick (square/ rectangular) polished area of each tiles not exceeding 0.36 Sqm in floors etc., set and jointed in neat cement slurry and pointed in white or colour cement to match with and including provision of 15 mm thick screed bedding in CM (1:6), complete all as specified and directed. 22 M&L for Vitrified ceramic tiles 9 to 10 mm thick (square/ rectangular) polished area of each tiles not exceeding 0.36 Sqmfor vertical surfaces skirting/Dado etc., set and jointed in neat cement slurry and pointed in white or colour cement to match with and including provision of 10 mm thick screed bedding in CM (1:4), complete all as specified and directed. 23 M&L for Glazed ceramic coloured tiles of 7 to 8mm thick, (square/rectangular) area of each tiles exceeding 0.11 Sqm but not exceeding 0.18 Sqm asfor vertical surfaces skirting/Dado etc.,set & jointed in neat cementslurry and pointed in white or coloured cementto match the colour of tiles over and including screed bed or bedding layer of 10 mm thick in CM (1:4) complete all as specified & directed by Engineer-in-charge 24 M&L for Machine cut kota stone slab flooring with Kota stone of size 550 x 550 mm 20-25mm thick over and including screed bed or bedding layer of 20mm thick in CM (1:6) cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed. 25 M&L for Kota stone slab 15-20 mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed or bedding layer of 10mm thick in CM (1:6) cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed. 26 S&F Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, Size of frame 105 x 60mm complete all as specified and directed. 27 M&L for PCC, 1:3:6 using 12.5 mm graded stone aggregate for filling door framescomplete all as specified and directed. 28 M&L for 35 mm thick factory made panel shutters 2nd class HW Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed. 29 S&F for Solid PVC door frame of size 50mm x 47 mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying & fixing in opening as per spcification etc, complete all as specified and as directed. 30 S&F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site complete all as specified and as directed. 31 S&F 100mm butt hinges, stainless steel medium weight fixed with stainless steel screws. Complete all as specified and directed. 32 S&F, aluminium handles , 150 mm size, cast type anodised. Complete all as specified and as directed. 33 S&F floor door stopper aluminium body double tounge anodised with hard drawn steel spring 140mm long complete all as specified. 34 S&F, Aluminium anodised barrel tower bolts, 150 mm long , of extruded section and fixed . complete all as specified. 35 S&F, aluminium alloy anodised slidingdoor bolts , of 250 mm long with hasp,staple(bolt type) fixing clips of sheet cast or extruded section , fixing bolts and sliding bolts of extruded section and fixed. 36 S&F in replacement Stainless Steel curtain rod20mm dia all as specified and directed by Engineer-in-Charge 37 S&F in replacement curtain brackets with finials of SS type(of approved colour and design) including fixing to walls with MS full screws(including fixing of wooden pieces of required size of walls) all as specified and directed by Engineer-in-Charge. 38 S&F in replacement aluminium anodised tubular curtain rod, 20mm dia, as fixed in repairs, complete all as specified and directed. 39 S&F bracket for 20 mm dia tubular curtain rod(for item above) complete all as specified and directed 40 S&F in replacement brass 4 Levermortice lock, vertical type,size 100mmcomplete all as specified . 41 S&F in replacement brass 2 Levermortice lock, vertical type,size 100mmcomplete all as specified . 42 Taking down chowkhats or framesexc 1.5 sqm but n exc 4 sqm each with shutters (without taking of shutters from the frames) and removinf from the site. 43 Taking down chowkhats or frames n. exc 1.5 sqm each with shutters (without taking of shutters from the frames ) and removing from site. 44 Taking down shutters of any description exc 1.00 sqm but n.exc 2.00 sqm each, from chowkats, complete all as specified 45 S & F for Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors,windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size,including necessary filling up the gaps at junctions, i.e. at top,bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle,Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge. 46 S&F aluminium window side hung shutter with aluminium section (with 50 micron powder coated) size of frame 125mm X 44.5 mm, size ofshutter, top, bottom and side rail 44.5mmx44.5x16 gauge and 5mm thick black/tinted sheet glass to be fixed on glazed portion and with galvanised mild steel wire cloth nominal dia of wire 0.56mm and average width of aperture 1.14mmstainless steel hooks and eye to be provided as stay of shutter etc complete incl necessary jointing cleats, glazing clips, rubber packing attached aluminium snap beading, screws,aluminium grill, anodized aluminum fitting such as peg stay 150mm long(01 No. for each leaf)hinges type B-21 100mm long (02 Nos for eachleaf) suitable handle (01 No for each leaf) and 100mm aluminium tower bolts (02 Nos in each leaf),brush weather strip,complete all as specified and directed. 47 S & F for aluminium powder coated of any colour door with one or more shuttersaluminium section weighing 0.55 kg/mincluding 5 mm thick plain/ coloured/ frosted sheet glass or ACP sheet and stainless steel wiremesh and connected itmes such as necessary joining cleats, glazing clips, rubber packing, aluminium snap beading, screws, pegstays 150mm long , hinges type B-21 100mm long , suitable handle, alum tower bolt including mortice lock and brass door stopper, complete all as specified and directed. .(Note :- Minimum thickness of powder coating not less than 50 micron). 48 S&F steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, holdfast and concrete bed block complete with outer side glazing bars shutter and inner side wire mewh shutter including glass panes, dovetailed or welded complete all as specified and directed. 49 -ditto- all as above but without glazing bars complete all as specified and directed. 50 M&L framed work such as grills, gratings etc with ends of bars shouldered and/or revited or forged into spikes framed guard bars and similar works conforming to Fe-410 or Fe-310-0 and embeded in concrete over compound wall incl necessary welding to the existing grills complete all as specified 51 Hacking out old broken glass of (any thickness, size and description) n exc 0.50 sqm in each pane from metal frame glazing with oil putty or fixed with beads etc. Complete all as specified and directed . 52 M & L for 3mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.50 Sqm in each panes as specified. 53 M & L 4.8mm thick sheet glass ordinary quality and glazing with clips in squareexc 0.50 Sqm in each panes Compete all as specified and directed. 54 M&L Solar control film 25 micron reflective type (garware sun control or equivalent complete all as specified. 55 M & L for 4mm thick Figuredglass pinhead typeand glazing with oil putty in square not exc 0.50 Sqm in each panes as specified. 56 S&F for Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm fixed with tinned tacks, or galvanised wire staples complete all as specified and directed . 57 S&F for PVC (SWR) pipes single socketed in any length with rubbering joints fixed to walls 110mm bore including taking down existing pipes complete all as specified and directed . 58 S&F in PVC (SWR) bends any radius 110mm bore with access door.complete all as specified and directed . 59 Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness with grid of any type and pattern including cover fillets complete all as specified and directed to engr-in Charge. 60 S & F forHangers 6 mm dia. G.I. (upto1200mm length) adjusting levelfixed to roof slabs by means ofceilling cleats made out of G.I. flat 40 x 3 mm size 60mm longand expansion hold fasteners12.5mm dia. 40mm longcomplete all as specified. 61 M&L for 12mm thick perforated gypsum board fixed in ceiling for insulation or accoustic purpose, flat or sloping fixed and including anodised aluminium to snap grid as per clause 10.38 of SSR Part-I (2009) of size 600 x 600 mm with staple pins complete all as specified and directed to engr-in Charge. 62 M&L for Plain cement concrete 1:4:8 type D2 (40 mm Graded aggregate) in foundation filling & mass concrete complete all as specified. 63 M&L 100mm thick cement concrete type D-2, 1:4:8 (40mm graded stone agrregate) as sub-base to floor etc complete all as specified. 64 Dismantling mild steel work of any driscription and any position complete all as specified. 65 Dismantlingfor Plain or corrugated steel sheeting,any gauge, thickness, including Nainital or similar pattern roof coveringscomplete all as specified. 66 S&F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1998 grade St-240 complete all as specified and directed. 67 M & L rolled mild steel as in (Beam, Tee, Angle, Channels) fixed independently without connecting plates etc (cut to ordinary length) conforming to Fe410-W (Gde-E-250) quality-A all as specified and directed by Engr-in- charge 68 S&F mild steel screwas bolt (Machine made) with hexagonal or square heads one end screwed, each screwed end have two washer and one nut, dia of shank 11mm-15mm and length of bolt not exc 5 cm long. all as specified and directed by Engr-in-charge. 69 S&F Pre-painted galvalume aluminium zinc coated GI based corrugated steel sheet 0.50mmthick of approved colour having tensile strength 550 MPa as in roof covering/cladding to wall fixed with self tapping screws including side and end lap as per manufacturer’s instructionscomplete all as specified and directed. 70 M&L for preparation of new or previously untreated steel surfaces of any description, over 10cm in width or girth not otherwise described by applying two coats synthetic enamel paint over a coat or red oxide zinc chrome primer complete all as specified and directed 71 Repair aluminium door and window shutters by taking down shutter from frame, opening out joints, taking out glass or panels of any description, replacing the corner piece wherever required , joining and assembling again, refixtethe glass pane and paneis by provision of new rubber neoprene packing complete all as specified and directed. 72 Resecuring,easing & adjusting without taking down /window shutters notexceeding 1 sqmfor easy operation, tighting hinges, adjusting position of hinges, tower bolts, sliding bolt etc including provision of necessary screws complete all as specified and directed. 73 Resecuring,easing & adjusting without taking down /window shutters exceeding 1 sqm but not exceeding 2 sqm for easy operation, tighting hinges, adjusting position of hinges, tower bolts, sliding bolt etc including provision of necessary screws complete all as specified and directed. 74 Resecuring,easing & adjusting without taking down /window shuttersexceeding 2 sqm for easy operation, tighting hinges, adjusting position of hinges, tower bolts, sliding bolt etc including provision of necessary screws complete all as specified and directed. 75 Supply and fix rotational moulded polyethylene water storage tanks white coloured three layered (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR part-I ,500 ltr capacity including, 20mm dia Ball brass valves, high pressure, with polyethylene float and fly nut complete, screwed for iron pipe or brass ferrule and fixed inlcuding taking down old tank complete all as specified and directed. 76 Supply and fix rotational moulded polyethylene water storage tanks white coloured three layered ( cylindrical vertical with closed top ) hoisted and fixed in position all as specified in SSR part-I ,1000 ltr capacity including, 20mm dia Ball brass valves, high pressure, with polyethylene float and fly nut complete, screwed for iron pipe or brass ferrule and fixed taking down old tank. complete all as specified and directed. 77 S&F Medium grade GI tubing 15 mm bore with all fittings fixed, to walls, ceiling or laid in floors including taking down old tubing etc.complete all as specified and directed. 78 S&F Medium grade GI tubing in 20mm bore pipe with all fittings, to walls, ceiling or laid in floors including taking down old tubing etc.complete all as specified and directed. 79 S&F in repairs gun metal globe or gate valves with iron wheel head screwed both end for iron pipe and fixed in repairs to 15 mm bore pipe.complete all as specified and directed. 80 S&F in repairs gun metal globe or gate valves with iron wheel head screwed both end for iron pipe and fixed in repairs to 20 mm bore pipe.complete all as specified and directed. 81 S&F in repairs for stop Valve copper alloy but fancy type and chrominum platedscrewed down high pressure with crutch or butterfly handle screwed both ends for iron/pipe or for union and fixed 15 mm bore in repairs complete all as specified and directed. 82 S&F in repairs bib taps 15 mm dia cast copper alloy chromoum plated fancy type with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed in repairs complete all as specified and directed. 83 S&F in repairs Angle stop valve of PTMT any colour high pressure screwed for iron pipe and fixed, (Minimum weight 15mm-90gms) complete all as specified and directed. 84 S&F in repairs Viterious china White Wash Hand Basin fixed in repairs includign 15 mm pillar cock cast copper alloy CP, 15mm cast copper stop valve, 32 mm brase CP waste fitting, PVC waste pipe 32 mm dia & 15 mm PTMT connection pipe 450 mm long complete all as specified and directed. 85 S & F as in replacement 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers 86 S& F in repairs Soap dish, any type, fixed to plugs with chromium plated brass screwscomplete all as specified and directed. 87 S&F in replacement CP Tubular towel rail (with hook) 20 mmdia 600mm long between flanges with and including chromium plated brass screws and wooden/plastic screws. complete all as specified and directed. 88 S&F in replacement vitreous china bowl urinal flat back, size 465x355x265mm white with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe. complete all as specified and directed. 89 Supply and fix in repair 10 ltr, PVC, valveless, syphonic action type, flushing cistern, low level/ high level including inlet, ball valve, float and handle including brackets with and including PVC flush pipe 32 mm bore, connecting to WC with PVC telescopic pipecomplete all as specified and directed. 90 S&F in repair PVC waste pipe 32mm dia for WHB ISI marked complete all as specified and directed. 91 S&F in repair PVC coupling for WHB 32mm dia complete all as specified and directed. 92 S&F in repair 32mm Bottle trap of PTMT having minimum water seal of 25mm (Minimum weight 32mm-260gms/40mm-270 gms) 93 S&F in repairviterous china wash down water closet pan, white (pedestal pattern), including plastic water closet seat, black/white, closed pattern with recessed bottom and cover and mild steel chromium plated or aluminised hinging device, (excluding fixing bolts, flushing cistern) and inlcuding flush pipe set of CP jet with PVC pipe of superior quality complete all as specified and directed. 94 S & F Grating round 140 mm size of PTMT. (Minimum weight 50gms) 95 Pillar taps, 15 mm borecast copper alloy chromium plated , with capstan heads, screwed down high pressure, with or without lettered Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe fixed as in repair, complete all as specified and directed by the Engineer in Charge. 96 S&F as in replacement 15mm size PVC connection 600 mmlong with PTMT nuts. complete all as specified and directed. 97 M&L for providing precast cement concrete louvers or Jali 25 mm thick (measured solid), made out of cement concrete 1:2:4 Type B-0 ,using 12.5 mm gaded stone aggregates and set in cement mortor 1:4, including moulding but excluding frame (precast frame shall be measured seprately) including demolition of old RCC jali, complete all as specifified and directed. 98 Pre-cast cement concrete RCC designer pillar of size 100mmx100mmx900mm made out of cement concrete 1:2:4 Type B-1 ,using 20 mm gaded stone aggregates and set in cement mortor 1:4 including all mouldings etc.Complete all as specified and directed bby Engineer-in-Charge. 99 Dismantling boarding, any description, fixed in any position with screws and removing from site. complete all as specified and directed. 100 S&F Solid PVC wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications. complete all as specified and directed. 101 S&F Solid5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and directed. 102 Taking down of existing rolling shutters of area of one shutter appx 10 Sqm easing, adjesting, greasing of anchoring rod, side guided plate, bevel gear box top cover etc, by mechanical means incuding minor repair/welding etc, shutters smooth operation and refixing the same. Complete all as specified and directed by Engineer-in-Charge. Note:-1. The work shall be executed through any approved workshop with prior approval of GE. 2. All necessary safety measures shall be taken during execution of work.3. All necessary repairs/minor items such as nut,bolt, washer, T & P,crane etc shall be provided to ensure smoothclosing/opening of the rolling shutters without any extra cost to the govt. 103 Contract Amount shall be derived after deducting the amount of Schedule of Credit in General Summary of tender documents.
