|
| 1 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. (a) Group C |
| 2 | Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. |
| 3 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.i) 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire |
| 4 | 2 X 6 sq. mm + 1 X 6 sq. mm earth wire |
| 5 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. (i)5/6 A switch |
| 6 | (1) 3 pin 5/6 A socket outlet |
| 7 | Supplying and fixing 230 V 50 Hz 5 stepped type2 module electronic fan regulator (Anchor deluxe) on the existing switch box including connections etc. as required. |
| 8 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required. |
| 9 | Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required. |
| 10 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular switch, connections etc. as required. |
| 11 | Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, \"C\" curve including connections, painting etc. as required |
| 12 | Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess,complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) (a) 08 Way Double door |
| 13 | 12 Way Double Door |
| 14 | Supplying and fixing following way,horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, onsurface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) a) 4 way (4 + 12), Double door |
| 15 | Supplying and fixing 5 amps to 32 amps rating, 240/415 volts 10kA, \"C\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. (i) Single pole |
| 16 | Double Pole |
| 17 | Triple Pole |
| 18 | Earthingwith GI earth pipe4.5mtr long x 40mm dia including accessories and providing masonary enclosure with cover platehaving locking arrangement and watering pipe etc( withcharcoalor coke and salt ) complete as required. |
| 19 | Providing and laying earth connection from earth electrode with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth electrode including connection with G.I. thimble excavation and re-filling as required |
| 20 | Supplying and making end termination with brass compressiongland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KVgrade as required. (i) 2 x 25 sq. mm (28 mm) |
| 21 | 3.5 x 35 sq. mm (32 mm) |
| 22 | 3.5 x 70 sq. mm (38 mm) |
| 23 | Providing, laying and fixing 65 mm dia G.I. pipe (medium class) in ground complete with G.I. fittings including trenching (75 cm deep) and re-filling etc as required. |
| 24 | Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc.conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required. (i) 63 mm dia |
| 25 | Supplying and Laying of armoured 2 x 25 sq mmone number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required..Make as per NIT (Before the installation of the cable approval will be have to be taken from the engineer in-charge) |
| 26 | Supplying and Laying of 3.5 x 35 sq mmone number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.Make as per NIT (Before the installation of the cable approval will be have to be taken from the engineer in-charge) |
| 27 | Supplying and Laying of armoured 3.5 x 70 sq mmone number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required..Make as per NIT (Before the installation of the cable approval will be have to be taken from the engineer in-charge) |
| 28 | SITC of water protected outdoor type compartmentalized hut type double door cubical panel of size 500 mm depth suitable for 415 Volt, 3 phases, 50 Hz made out of 2 mm thick CRCA sheet with required hardware duly painted with powder coated. The panel having 100A/415V and 160A/415V 4 strip aluminum bus barsets duly PVC sleeved, separate detachable gland plate, angle iron base frame made out of 65 mmx 65 mm x 6 mm angle iron of suitable size of the panel {minimum height 2 meter (one meter below the ground level and one meter above the Ground level), 4 Nos hinged at door, withHandle locking arrangement for inside/outside separately, earth bar/stud, i/c grouting the legs in 1:3:6 cement concrete foundation and brick work around the three sides of panel to supporting complete as required with following instruments mounted on it. (Panel should beas per design &drawing approved by Engg in charge & CPRI approved)Instruments(Inside/outside)i) 0-500 Volts, digital voltmeter ii ) 0-300 Amps, Digital Amp meter iii)LED Pilot light (22.5 MM dia) with03 Nos with 6 amp MCB on door closure |
| 29 | Providing and fixing of following accessories in the existing panel as per item 20 (i) 100 Amp 16 KA FPMCCBwith fixed thermal & fixed magnetic Ics- 100 %,long with neutral connector etc. as requiredMake as per NIT (Before the installation of the MCCB approval will have to be taken from the engineer in-charge) |
| 30 | 63 Amp 25 KA DP MCCBwith fixed thermal & fixed magnetic Ics- 100 %,long with neutral connectoras etc. requiredMake as per NIT (Before the installation of the MCCB approval will have to be taken from the engineer in-charge) |
| 31 | Supply, Installation, Testing and Commissioningof 1200 mm sweep, ceiling fan , class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding,electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC etc. requiredMake as per NIT (Before the installation of the fan approval will have to be taken from the engineer in-charge) |
| 32 | Supplying and Installation of 300 mm sweep Ventil Air DSP metallic Exhaust Fan suitable for operation on 230 V,Single Phase, 50 Hz AC Supply of900 rpm in the existing opening,connection, testing, commissioning etc. as required. etc. requiredMake as per NIT (Before the installation of the Ex Fan approval will have to be taken from the engineer in-charge) |
| 33 | supply, installation, testing and commisioning of 25 Watts, 230 V, 50 Hz,Decorative ultra slim polycarbonate LED Tube Light fixture with high lumen output, high wattage PC Batten, environmental friendly,energy efficient ready to use pack.etc. requiredMake as per NIT (Before the installation of the Fixtures approval will have to be taken from the engineer in-charge) |
| 34 | Supply and installation of suspended/surface mounted 36 watt LED Light fixture with high lumen output, size - 1200 x 56 x 87 mm with chain, aluminium housing etc as required make of Havells modle no RADIANTELP/S36WLED857WH1200SD/Make as per NIT (Before the installation of the Fixtures approval will have to be taken from the engineer in-charge) |
| 35 | Supplying and fixing of wall type 10 Watt LED bulk head fitting, suitable for outdoor and indoor, IP65 and above, IK&surge protecion for long lasting performance etc. as required Make as per NIT (Before the installation of the Fixtures approval will have to be taken from the engineer in-charge) |
| 36 | Making the hole in brick wall and making good the damage for installation of Exhaust fan etc. as required at site up to 450 mm |
| 37 | Supply and fixing 80 watt LED Flood light Energy saving, environmental friendly, long life, die cast aluminium housing with LEDs as light source,suitable for highlighting architectural features or area lighting with 3-5 years warrantyMake as per NIT (Before the installation of the Fixtures approval will have to be taken from the engineer in-charge) |
| 38 | Providing and fixing of 400 mm single phase, swing wall fanIndexable to different positions up to 15 degrees , Oscillation up to 90 degrees for total flexibility ,i/c connections, fixing on (300 x 150 x 1.5 )mm iron plate and testing etc as reqd.Make as per NIT (Before the installation of the Wall Fan approval will have to be taken from the engineer in-charge) |
| 39 | Supplying, installation, testing and commissioningof 2 TonSplit Air Conditioner complete set with indoor unit (IDU), out door unit (ODU), suitable for 230 V ±10% of 50 Hz single phase AC supply, 6000 Kcal:: Hr normal cooling capacity, AC with 3-5 mtr copper pipe and suitable, capable of performing cooling, air circulating filtrating with remote contral with 3 Star rated, Copper condencer and copper coil, Warranty of machine-1-5 year and compressore-5-10 years etc as required, and 4 KVA automatic stabilizer for 1.5/2.0 Ton capacity split type air conditioner, working voltage range input-130V-280V and out put 130V-2800V,type of winding is copper,Make- V Guard , Voltas,microtek, skyland, Denen or equivalent . |
