|
| 1 | Dismantling of brick or brick tiles laid bedded and pointed in any mortar on roof including cleaning for refixing etc complete all as specified & directed |
| 2 | Demolition of cement concrete of any description and in any position not otherwise specifically provided for etc complete all as specified & directed |
| 3 | M&L for providing PCC 1:2:4 type-B1, (using 20mm graded stone aggregate) in roof paddingcomplete all as specified & directed by Engr-in-Charge. |
| 4 | M & L for providing 15 mm thick plaster in CM 1:4 mixed with polymer based water proofing compound when concrete is still green etc complete and all as directed by Engr-in-Charge |
| 5 | M & L cutting out cracks to V section in existing roof, chajjas or similar work up to 40 mm deep and cleaning the same with water jet to get rid of any loose material and wetting , grouting with cement & sand mortar 1:3 mixed with liquid WPC all as directed. |
| 6 | M & Lfor applying Smart Care Damp proof Ultra fibre reinforced elastometric liquid applied water proofing membrane as in roof treatment @ 1 Litre per 10 sqft inclusive of all three coats as per following application process:-(a) Prepare the surface by cleaning with high pressure water jet/wire brushes to ensure that it is free of dust, oil, grease, grime and loose particles.(b)Damaged portion if any to be repaired before application of roof treatment as per manufacturer\"s instruction.(c) Applying self priming coat of Smart Care Damp proof Ultra duly diluted with water in 3:1 ratio by volume.Allow the primed surface to dry for at least 3-4 hours prior to application of subsequent coat. (d)Applying 2 perpendicular coats of Smart Care Damp proof Ultra without any dilution to achieve a forced system coverage.Allow it to dry for at least 4-6 hours between two coats . NOTE:WORK SHALL BE CARRIED OUT BY THE AUTHORISED APPLICATORS OF THE MANUFACTURER IN CLOSE SUPERVISION OF EXECUTVE STAFF UPTO ENGINEER-IN-CHARGE LEVEL. Contractorshall give 05 yearsGuarantee for water proofing treatment carried out. |
| 7 | Taking up or down steel tubing 15 mm dia bore steel and connections including clearing for refixing or removal to store complete all as specified and directed. |
| 8 | Taking up or down steel tubing 20mm dia bore and connections including cleaning for refixing or removal to store complete all as specified and directed. |
| 9 | M&L for cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings steps, cills, sunshades, shelves, lintels etc, and cutting chases for concealed water tubing etc and making good, cuttingn exc 10cm girth in brick walls complete all as specified & directed. |
| 10 | Supplying and laying of 20 mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed. |
| 11 | S&F GI tube 20mm medium grade; with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified & directed. |
| 12 | Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store & rubbish of the premises. |
| 13 | M&L Non Skidceramic colouredtiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to matchcomplete all as specified and directed. |
| 14 | M&L Non skid ceramic tiles 7-8mm thick coloured (Square/rectangular) area of each tiles exceeding 0.18 sqm but n exc 0.36 sqmin floors set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed. |
| 15 | M&L for screed bed or bedding layer of mortar 15 mm thick for laying floor finishes etc in Cement Mortar 1:4 complete all as specified and directed. |
| 16 | M&L Non skid ceramic tiles 7-8mm thick coloured (Square/rectangular) area of each tiles exceeding 0.18 sqm but n exc 0.36 sqmin dado/skirting set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed. |
| 17 | S&F Glazed ceramic tiles colouredin vertical surface 450X300X7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed. |
| 18 | M & L for rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 for backing of Dado/ Skirting,complete all as specified and directed. |
| 19 | Dismantling stone slabs and tiles of any description or thickness in floors, aprons etc.laid, bedded and pointed in any mortar complete all as specified & directed. |
| 20 | S & F16-18 mmthick Granite (Jet Black) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platformsincluding pointing in white cement (1:2) using marble dust with admixture of pigment to match withshade of granite complete all as specified. |
| 21 | M&L Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified. |
| 22 | M&L machine cut kota stone slab flooring 18-20mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed. |
| 23 | M & L for Kota stone slab 18-20mm thick in riser of steps, skirting, dado and pillar laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, complete all as specified and directed. |
| 24 | M&L for Mirror polishing on marble/granite/kota stone/stone work where ever required to give high gloss finish by machine complete all as specified and directed. |
| 25 | Demolition of cement concrete(unreinforced)not exceeding 15 cm thickness(below or aboveground level) complete all as specified and directed. |
| 26 | M&L 75mm thick PCC (1:4:8) type D-2 using 40mm graded stone aggregate as in subbase of flooringcomplete all as specified and directed. |
| 27 | M&L Chequred cement concrete tiles 30cmx30cmx 25mm thick set jointed and pointed in neat cement slurry in floors with grey cement and pigment, complete all as specified and directed. |
| 28 | M & L for screed bed or bedding layer of mortar 20 mm thick for laying floor finishes etc in Cement Mortar 1:6 complete all as specified and directed. |
| 29 | M&L for 50 mm thick cement concrete 1:3:6, type C1, using 20mm graded crushed stone aggregate as in plinth protection, laid in slope of 1:20 and surface finished even and smooth without using extra cement including making joint at 3m interval and at each corner the joint shall be filled with bitumen mastic filling to full depth (comprising one part hot blown bitumen 85/25 and two part of sand), complete all as specified and directed. |
| 30 | Demolition of brickwork/stone boulders, masonary built in cement mortar incl all quoins, arches,pillars,etc. but excl ashlar facings, dressed stone works & precast concrete surfaces. |
| 31 | M&L brick work with sub class \"B\" bricks old size best quality bricks straight or curved on plan exc 6 M mean radius built in CM (1:6) all as specified and directed. |
| 32 | M&L Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified. |
| 33 | Taking down cement plaster on brick or stone wall etc incl racking out joints hacking for key, scrubbing down with water etc. |
| 34 | M&L for Rendering 15 mm thick on fair faces of brick or concrete surface walls, in cement mortar 1:4 , rendering is to be finished even and fair without using extra cement (up to 3rd storey with necessary scaffolding) complete all as specified and as directed by Engineer-in-charge. |
| 35 | M&L for Rendering 15mm thick on surface other thanfair faces of brick work or concrete surfaces or on stone masonry surfaces or on one side of lathing in cement mortar 1:6 finished even and smooth without using extra cement, complete all as specified and directed. |
| 36 | M&L for rendering 5 mm thick on ceiling surfaces in cement mortar 1:3 and finished smooth and even without using extra cement complete all as specified and directed. |
| 37 | M&L for complete removal of existing treatment by mechanised method and applyingtwo coats of OBD by Roller over one coat of 1-2 mm thick wall care putty and a coat of primer complete all as specified and directed. |
| 38 | Material and labour for preparation of new plastered surfaces of walls & applying two coats of oil bound distemper over two coat of wall care putty of 1 to 2 mm thick and one coat of primer complete all as specified and directed. |
| 39 | M&L for preparing newly plastered surfaces of ceilings and applying three coats of white wash complete all as specified. |
| 40 | M&L for preparing old plastered surfaces of ceilings and applying two coats of white wash incl complete removal of old plastered surfaces. |
| 41 | M&L for preparation of newly plastered surfaces applying two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/10 Sqm over and includingpriming coat of exterior primer applied @ 0.90 litre/ 10 Sqm over new prepared surface complete all as specified including necessary scaffolding arrangement and as directed by Engr-in-Charge. |
| 42 | M&L for complete removal of existing treatment from surfaces of RCC/stone/concrete/brick walls of any description including preparation of scraped surface by removing all depression and applying two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/10 Sqm over and icluding priming coat of exterior primer applied @ 0.90 litre/ 10 Sqm over new prepared surface complete all as specified including necessary scaffolding arrangement and as directed by Engr-in-Charge. |
| 43 | Taking down chowkhat or frames with shutters without taking off shutters from the frames) n exc 1.5 Sqm each complete all as specified and directed. |
| 44 | Taking down chowkhat or frames with shutters without taking off shutters from the frames) exc 1.5 Sqm and n exc 4.0 Sqm each complete all as specified and directed. |
| 45 | Taking down shutter of any description exc. 1.00 Sqm & nexc. 2.00 Sqm each complete all as specified and directed. |
| 46 | S&F pressed steel framesof size 105mm x 60mm made outof size 1.25mm thick MS sheet for doorssingle rebated including mild steel hinges medium weight 100 mm long and 25mm x 3mm flat iron in holdfast,tie bar including necessary fixinglugs, hold fast, lock strike plate and fixing arrangement etc complete as specified and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-1 including one coat of red oxide primer all as Specified and directed by Engr-in-Charge. |
| 47 | S&F pressed steel framesof size 125mm x 60mm made outof size 1.25mm thick MS sheet for doorsdouble rebated including mild steel hinges medium weight 100 mm long and 25mm x 3mm flat iron in holdfast,tie bar including necessary fixinglugs, hold fast, lock strike plate and fixing arrangement etc complete as specified and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-1 including one coat of red oxide primer all as Specified and directed by Engr-in-Charge. . |
| 48 | M&L for providing PCC type C0 (1:3:6) using 12.5mm graded stone aggregate as in filling pressed steel door frame etc complete all as specified and as directed |
| 49 | M&L for 30 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercialtype on both sides etc complete all as specified and directed. |
| 50 | M&L glazed & skeleton shutters 35mm thick 2nd class Hard wood open rebated & prepared to receive glass, gauge etc. edges of framaing plain, chamfered or rounded fitted with cut and mitred beads for securing glass etc. sized of members of shutter with three number of pannels all as specified and directed. |
| 51 | Providing and fixing factory made UPVC white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners,Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories Area exceeding 2.00 sqm each(Note:The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net Opening will be measured lor payment purpose.) |
| 52 | Providing and fixing factory made UPVC white colour casement (Openable) window made of extruded profiles with wall thickness of 2.3mm ( + – 0.2mm). Window profile with hollow section with multi chamber, frame (60mm x 58mm), sash (60mm x 73mm), T profile (One vertical length in between two shutters) (60mm x 74mm), Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket 1.2 +– 0.2mm thick, galvanized steel Frame (28mm x 21.5mm), sash (31mm x 27.5mm). T profile (27mm x 17mm) to be inserted in required profile, frame will be fixed to the wall with 8 mm x 100mm long fasteners. Hardware: [casement handle made of zinc alloyed (white powder coated), But Hinges of\"zinc alloyed (white powder coated), transmission gear made of mild steel with multi point locking system] and 5mm thick glazing with selected quality glass.(Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net opening will be measured for payment purpose.)(i)Area exceeding 1 sqm but n exc 2 sqm each |
| 53 | M&L for solid PVC door frame of size 50mm x 47 mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube complete all as specified and directed. |
| 54 | S&F Factory made solid PVC Moulded door shutter 28 to 30 mm thick (Stiles) with particle board core with 2, 4 ,or 6 raised panel design with 2 mm thick mouldedPrelam PVC sheet on the front face & 2 mmPrelam PVC sheet on back face, to be fitted in the mild steel frame welded/sealed to the stiles and rails with suitable PVC sheet beading, and joined together with solvent cement, supplying and fixing in the frame at site as per specification and drawing, complete all asspecified and as directed by Engr-in-Charge. |
| 55 | S&F 100mm butt hinges , extruded aluminium alloy with galvanised mild steel hinge pin , anodised and type B-22 etc complete all as specified and directed. |
| 56 | S&F 100 mm long Butt hinges, medium weight, cold rolled mild steel and fixed, complete all as specified and directed. |
| 57 | S & F200 mm long Aluminium, anodised, barrel tower bolts of extruded section, complete all as specified and directed. |
| 58 | S & F150 mm long Aluminium, anodised, barrel tower bolts of extruded section, complete all as specified and directed. |
| 59 | S & F of 125mm Extruded aluminium alloy handles, fabricated type, anodised, complete all as specified and directed. |
| 60 | S & F of250 mm aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed. |
| 61 | S&F of 4.0 mmthick sheet glass ,ordinary qualityand size exc 0.50 Sqmand fixed to door/window shutter and partition wall by means of glazing clips rubber strips etc. complete all as specified and directed. |
| 62 | S&F stainless steel wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.4mm and fixed withs stainless steel wire staples etc complete all as specified and directed . |
| 63 | Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads |
| 64 | M&L for cement concrete type B1 1:2:4 (using 20mm graded aggregate) as in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, fixing of holdfast, plinth courses , string courses, lacing courses parapets and railings upto 60cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed. |
| 65 | M & L for preparation of new or previously untreated wood and wood based surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed. |
| 66 | M & L for preparation of old painted wooden surfaces exc. 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed. |
| 67 | Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for |
| 68 | M&L for RCC (NominalMix) type B1, 1:2:4, using(20 mm graded stone agg) for Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and directed. |
| 69 | Use & waste of formwork to sides and soffits of lintels, cantilevers, shelves including supports for rough finished flat surfaces of concrete. |
| 70 | M & L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips. |
| 71 | Applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 Kg per sqm including cleaning surfaces etc complete as in sunken portion etccomplete all as specified and directed. |
| 72 | M & L cement concrete type E2, 1:5:10 (40mm graded stone aggregate) as in filling and mass aggregate complete as specified and directed. |
| 73 | M&L 25 mm thick PCC (1:2:4) type B-1 (20mm graded aggregate) as in sub base finishing the surface even and rough to receive the topping layer, complete all as specified and directed. |
| 74 | M&L for polythene film black 50micron thick, laid on a coat of bitumen primer @ 0.3-0.5 Kg/Sqm. |
| 75 | M&L 32 mm tubes medium grade galvanized with all fitting and fixed complete to walls and ceiling or laid in floors as in spouts. |
| 76 | Dismantling of Cast iron pipes 100 mm boreincluding allfittings like bend,branch pieces, connectors, heel rest bend etcfixed to wall and removing from site all as specified and directed Note :- Work will be carried out upto 3rd storey of bldgs also as per direction of Engr-in-charge including necessary formwork and scaffolding required as per site conditions & no extra payment shall be made on this account. |
| 77 | Dismantling of Cast iron pipes 75 mm boreincluding allfittings like bend,branch pieces, connectors, heel rest bend etc. fixed to wall and removing from site all as specified and directed Note :- Work will be carried out upto 3rd storey of bldgs also as per direction of Engr-in-charge including necessary formwok and scaffolding required as per site conditions & no extra payment shall be made on this account. |
| 78 | Supply and fixing of cast iron (spun) soil, waste and vent pipe 100 mm bore, any length with or without ear with cement joint,fixed to walls. |
| 79 | Supply and fixing of cast iron (spun) soil, waste and vent pipe 75 mm bore, any length with or without ear with cement joint,fixed to walls. |
| 80 | Supply and fixing of CI bend 100 mm bore with oval accessories door. |
| 81 | Supply and fixing of CI bend 75 mm bore with oval accessories door. |
| 82 | Supply and fixing of CI Branch pieces 100 mm bore, single (equal or unequal), ordinary or socket types or with parallel branches with oval access door. |
| 83 | Supply and fixing of CIvent cowl 75 mm size. |
| 84 | S & F in replacing Stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays of dia 100 mm, including bolts and nuts and securing ends of stays to wall or roof. |
| 85 | S & F in replacing Stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays of dia 75 mm, including bolts and nuts and securing ends of stays to wall or roof. |
| 86 | S&F in replacing vitreous china squatting pan Orrisa Pattern size 580x440 mm white with integral foot rest complete all as specified including lime concrete bedding . |
| 87 | Supply and fixing in replacing Vitreous china ware pedestal type water closet white, with \"P\" or \"S\" trap including connection to drain or out going pipe and to flushing pipe including Plastic water closet seat, white, closed pattern with recessed bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as directed. |
| 88 | S&F in replacing Bib taps 15mm dia cast copper alloy with chromium plated crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified & directed. |
| 89 | S&F in replacing 15mm stop cock/ Angle cock cast cooper alloy chromium plated of screwed down high pressure with long shank and cup concealed type , screwed with ends for iron pipe or unions.complete all as specified & directed. |
| 90 | S & F in replacingPVC flushing cistern 10 ltrs capacity valve less symphonic action type low level complete with inlet valve handles incl brackets, chromium plate brass flush pipe 32 mm dia PVC connection and incl taking down old high level cistern complete all as specified & directed. |
| 91 | Supply and fixing in replacing Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified & directed. |
| 92 | S&F PVC connection 15 mm size with PTMT nuts of length 600 mm complete all as specified and directed. |
| 93 | S & Fin replacement Vitreous China Ware Wash hand basin white, flat back, 550x400 mm sizeoval type in repairs including cutting for and pinning ends of brackets or erecting stand complete all as specified and directed. |
| 94 | S&F in replacement 15mm bore brass CPbasin mixer for mixing hot & cold water screwed down for iron pipe and fixed, complete all as specified and directed. |
| 95 | S & F in replacement CP brass Soap dish, fixed to walls with chromium plated (CP) brass screws complete all as specified and directed. |
| 96 | S & F in replacement 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers. |
| 97 | M&L for 32mm dia waste fittings, brass, chromium plated for glazed ware sinks, basins, etc with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed. |
| 98 | S&F in replacement 15 mm bore brass, chromium plated, sink mixer(wall mounted with 170 mm long swivel spout and wall flange,screwed down high pressure withlong screwed shanks and fly nuts, screwed for iron pipe. |
| 99 | S&F in replacement plate rack of size (24\"X36\"X10\") including fixing of screws complete all as specified. |
| 100 | S&F in replacement sinksmade of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipebowl size 600mm x 450mm x 160mm complete all as specified and directed. |
| 101 | S&F 32mm bore dia wast coupling of PTMT (half or full threaded) suitable for urinals, (Minimum weight 32mm-45gms) complete all as specified and directed. |
| 102 | S&F grating round 140mm size of Brass (minimum weight 50 gms) complete all as specified and directed. |
| 103 | S&F in repair Tubular towel rail, Chromium plated, 20mm dia, D type, 60cm long between flangescomplete all as specified and directed. |
| 104 | Dismantling water tanks and removing to store of water storage tanks (Cap. 500 ltr to 1000 ltr ) complete all as specified and directed by Engineer-in-charge. |
| 105 | Supply and fixingRotational moulded polyethylene water storage tanks of1000 litres capacity,(cylindrical vertical with closed top) with plastic lid cover, triple layered, white, hoisted and fixed in position all as specified in SSR Part-I including PTMT Ball valves high pressure with epoxy coated Aluminium rod & high density plastic ball complete, screwed for iron pipe or brass ferrule and fixed for 20 mm bore pipe, including making connections complete all as specified and directed. |
| 106 | M&L for 75mm dia PVC floor trap, with grating including jointing with solvent cement complete all as directed and specified |
| 107 | S&Ffor 75mm bore PVC [SWR] pipes single socketed, in any length with rubber ring joints, fixed to wall all as specified and directed |
| 108 | S&F 110 mm bore PVC (SWR) soil, waste, vent pipes single socketed in any length with rubber ring joints fixed to walls all as specified and directed |
| 109 | S & F in replacement of 25mm dia, stainless steel curtain rods including brackets and latto complete all as specified and as directed by Engineer-in charge. |
| 110 | S & F in repairs Hat pegs,Aluminium solid body, 125 mm to 175 mmcomplete all as specified & directed |
| 111 | Taking down of old/unserviceable kitchen cabinet/cupboard including all fixture and fitting, complete all as specified and directed.Note: For measurement superficial area in elevation shall be measured. |
| 112 | M&L 18 mm thick PVC board one side UV printed designing and back side plain colour printed for cub board boxes or kitchen cabinet with shelf, drawer, shutter and frame full size fitted under cooking platform and other platform including fittings etc complete all as specified and directed. |
| 113 | Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc.removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc.. complete all as specified and directed. |
| 114 | Taking down un-serviceable DB of any size and capacity including MCB etc, and removing materials to store for keeping in safe custody or for taking credit and making good disturbed surfaces of walls,floors, etc, and making good the disturbed surfaces on wall/floor etc complete all as specified and directed. |
| 115 | Taking down unserviceable sub main wiring with copper/aluminium conductor,PVC insulated,unsheathed cable of any size drawn through andincluding rigid PVC or PVC casing coping including earth wire complete all as specified anddirected. |
| 116 | M&L for Point wiring using approved colour coding as per IS (Red , Black and Green for single phase circuits),with multi stranded copper conductor 1.5 sq mm nominal cross-sectional area, single core, PVC insulated and unsheathed FRLS cable 1100 Volts grade, ISI-694 marked with valid CML No.in and including heavy dutydrawn through and including in PVC rigid conduit with all accessories complete concealed in wall/roof/floor etc, ISI marked with,including steelbox of required module forfixing ofmodular switches, sockets and fan regulators etc, inciuding PVC insulated multistranded copper conductor 1.5 sq mm nominal cross sectional area single core FRLS cable as earth continuity conductor to common earth and connecting to earth dolly for,one way switch One light/ fan/bell point controlled by one, one way switch complete all as specified and directed .Note : surface conduit shall be laid in ceiling portion only. |
| 117 | All as per Serial Item No. 116 above but for one light point controlled by two Nos. of, two way switches complete all as specified and as directed. |
| 118 | All as per Serial Item No.116 above but for one 3 pin socket outlet 5 Amps on the same board with other switches with multi stranded copper conductor 2.5 sq mm nominal cross-sectional area, single core, complete all as specified and as directed. |
| 119 | All as per Serial Item No. 116 above but one 3 pin socket outlet 5 Amps on independent board with multi stranded copper conductor 2.5 sq mm nominal cross-sectional area, single core,complete all as specified and as directed. |
| 120 | All as per Serial Item No. 116 above but One bell/buzzer point controlled by one push button on the same board with other switches or independent with cables 1.5 sq.mm size |
| 121 | All as per serial Item No.116 above but for 15 Amps 5/6 pin socket point on independent board with 2.5 Sqmm PVC insulated FRLS multi-strandedcopper conductor with 4.00 Sqmm PVC insulated FRLS multi-strandedcopper conductor as earth wire complete all as specified and directed . |
| 122 | Supply and Fixing Modular switch 1 way 6A, 1 module. |
| 123 | Supply and Fixing Modular switch 1 way16A, 1 module |
| 124 | Supply and Fixing Modular switch 2 way 6A, 1 module |
| 125 | Supply and Fixing Modular Bell push 6A, 1 module |
| 126 | Supply and Fixing Modular Socket, 6A - 2/3 pin combined 2 module, |
| 127 | Supply and Fixing Modular Socket, 6A/16A - 2/3 pin combined 2 module, |
| 128 | Supply and Fixing Fan step regulator, 120W - 2 module 2 module, |
| 129 | Supply and Fixing Modular White cover plate with frame,2 module |
| 130 | -Ditto- as per item No.129 above but 3 module |
| 131 | -Ditto- as per item No.129 above but 4 module |
| 132 | -Ditto- as per item No.129 above but 6 module |
| 133 | -Ditto- as per item No.129 above but 8 module |
| 134 | -Ditto- as per item No.129 above but 12 module |
| 135 | Supply and fixing of Bell,multi music type, AC, 230 volts, single pole complete all as specified and directed. |
| 136 | S&F Submain wiring with two runs of 4 sqmm with one run of 4 Sqmm earth wire of 1100V grade FRLSPVC insulated multi-stranded copper conductor, single core cable conforming to IS 694 drawn through concealed conduit and connected to common earth dollycomplete all as specified and directed.Note :- Three runs of 4 sqmm shall be measured as one length for the purpose of measurement. |
| 137 | S&F Submain wiring with two runs of 6 sqmm with one run of 6 Sqmm earth wire of 1100V grade FRLSPVC insulated multi-stranded copper conductor, single core cable conforming to IS 694 drawn through existing conduit and connected to common earth dollycomplete all as specified and directed.Note :- Three runs of 6 sqmm shall be measured as one length for the purpose of measurement. |
| 138 | Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size completeall as specified and directed. |
| 139 | Supply and fixing LED lights fitting 1x 20W, 220V,AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete. and connectiong up with twin core twisted flexible copper conductor cable with suitable size taking down old fitting complete all as specified and asdirected |
| 140 | S&F LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed by Engr-in-charge. |
| 141 | S&F Ceiling rose, surface bakelite, 65 x 50 mm, three terminals, 230 Volts complete all as specified and as directed. |
| 142 | S&F Factory made distribution board in sheet metal enclosure in double door with 200A ratedbus bar,SPN 8 way, 240V for fixing MCB\"s complete all as specified and as directed. |
| 143 | S&F Factory made distribution board in sheet metal enclosure in double door with 200A ratedbus bar,SPN 12 way, 240V for fixing MCB\"s complete all as specified and as directed. |
| 144 | S&F MCB SPN ‘B’ Curve 10KA, 40 amps complete all as specified and directed . |
| 145 | S&F MCB SP ‘B’ Curve 10KA, 5 to 32 amps complete all as specified and directed . |
| 146 | S&F MCB TPN ‘B’ Curve 10KA, 63 amps, 415V complete all as specified and directed . |
| 147 | S&F Blanking plate for filling gap of MCB complete all as specified and directed. |
| 148 | S&F Blanking plate for filling gap of switches any typecomplete all as specified and directed. |
| 149 | S&F Lamp Holder, insulated body with back plate, 230 Volts for batten fittings including taking down old one complete all as specified anddirected. |
| 150 | Supply and fixing Single pole and neutral enclosure with a two pin and earth plug and socket modular type complete with one single pole MCB 20Amps complete all as specified & directed. |
| 151 | Supply and fixing post top lantern LED type 20 watt 230 watt volts AC outdoor type with decorative post top for 360 degree indirect light IP 65 protection with impact and corrosion resistant complete with driver and lamp complete all as specified and as directed by Engr-in-charge. |
| 152 | M&L earthing complete with galvanised steel earth plate electrode 600 x 600 x 6mm thick, buried directly in ground (earth pit not less then 2.25m deep below ground level) with top edge of the plate not less then 1.5m deep below normal ground level connected to galvanised iron earth wire of 4.0 mm earth lead by means of bolt, nuts, washers of galvanised steelearth strip protected by and including GI pipe 40mm dia bore (light grade) and connected to main test point as directed and including concrete pit in PCC(1:3:6)type C-1 precast RCC(1:1.5:3)type A-1 cover slab 54 x 54 cm reinforced with 4mm dia TMT bars @ 150 mm c/c both ways with one handle for lifting made out of 8mm dia TMT bar embedded in precast cover slab funnel wire mens 20mm bore GI pipe (medium grade) for watering charcoal and salt in alternate layers, including necessary excavation and earth work in any type of soil complete all as shown on electrical plate No3 of SSR part-I complete all as specified and directed. |
