|
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. |
| 2 | All kinds of soil. |
| 3 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 and for all lif. |
| 4 | Providingandlayinginpositioncementconcreteof specified grade excluding the cost of centering and shuttering - All work up to plinth level : |
| 5 | 1:3:6 (1Cement : 3 coarse sand (zone-Ill) derived from natural sources : 6 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 6 | 1:4:8 (1Cement : 4 coarse sand (zone-Ill) derived from natural sources: 8 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 7 | Makingplinthprotection 50mmthickofcementconcrete 1:3:6 (1cement : 3 coarse sand (zone-Ill) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75 mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. |
| 8 | Providing and laying in position specified grade of reinforced cement concrete,excludingthecostofcentering,shuttering,finishingand reinforcement - All work up to plinth level : |
| 9 | 1:1.5:3(1 cement: 1.5 coarse sand (zone-Ill) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 10 | Reinforced cement concrete work in walls (any thickness),including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor fivelevel,excludingcost of centering,shuttering, finishingand reinforcement: |
| 11 | 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 12 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15 degree landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). |
| 13 | Centering and shuttering including strutting, propping etc. and removal of form for |
| 14 | Foundations,footings,basesof columns,etc.formass concrete |
| 15 | Shelves (Cast in situ) |
| 16 | Lintels,beams,plinthbeams,girders,bressumersand cantilevers |
| 17 | Weather shed, Chajjas, corbels etc., including edges |
| 18 | Columns, Pillars, Piers, Abutments, Posts and Struts |
| 19 | Steelreinforcement forR.C.C.workincludingstraightening,cutting, bending, placing in position and binding all complete upto plinth level. |
| 20 | Thermo-Mechanically Treatedbars of gradeFe-500D or more. |
| 21 | Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3(1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 22 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. |
| 23 | Fixed to openings /wooden frames with rawl plugs screws etc. |
| 24 | Providing 40x5 mm flat iron hold fast 400 mm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 300x100x150 mm 1:3:6 mix (1 cement: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size). |
| 25 | Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS: 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : |
| 26 | 300x16 mm |
| 27 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : |
| 28 | 250x10 mm |
| 29 | 100x10 mm |
| 30 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : |
| 31 | 125 mm |
| 32 | 100 mm |
| 33 | Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. |
| 34 | Twin rubber stopper |
| 35 | Providing and fixing to existing door frames. |
| 36 | 24 mm thick factory made PVC door shutters made of styles cleats. The shutter frame filled and rails of a uPVC hollow section of size 59x24 mm and wall thickness 2 mm (± 0.2 mm) with inbuilt edging on both sides. The styles and rails mitred and joint at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mmhavingwallthickness1.0mmandstainlesssteel screws. The styles of the shutter reinforcedby inserting galvanised M.S. tube of size 20x20 mm and 1mm (± 0.1 mm) wall thickness. The lock rail made up of \"H\" section, a uPVC hollow section of size 100x24 mm and 2 mm (± 0.2 mm) wall thickness, fixed to the shutter styles by means of plastic/galvanised M.S. with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer\"s specification and direction of Engineer- in-charge. (For W.C. and bathroom door shutter). |
| 37 | Providing and fixing factory made P.V.C. door frame of size 50x47 mm with a wall thickness of 5 mm, made out of extruded 5 mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer\"s specification and direction of Engineer- in-Charge. |
| 38 | Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 39 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. |
| 40 | Hot finished welded type tubes |
| 41 | Providing and fixing mild steel round holding down bolts with nuts and washer plates complete. |
| 42 | Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer. |
| 43 | G.I. pipes |
| 44 | Cement concrete flooring 1:2:4 (1cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. |
| 45 | 40 mm thick with 20 mm nominal size stone aggregate |
| 46 | Providingand fixingplainmultipurpose cement board(Hight pressure steam cured) with suitable screws for cement particle board in ceiling etc. complete (frame work to be paid seperatately). |
| 47 | 6 mm thick Cement fiber board, Type-B, Category-III as per IS: 14862 :2000 |
| 48 | 12 mm cement plaster of mix: |
| 49 | 1:4(1 cement: 4 fine sand) |
| 50 | Neat cement punning. |
| 51 | Finishing walls with Acrylic Smooth exterior paint of required shade: |
| 52 | New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) |
| 53 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : |
| 54 | Two or more coats on new work |
| 55 | Painting with black anti-corrosive bitumastic paint of approved brand and manufacture to give an even shade: |
| 56 | Two or more coats on new work |
| 57 | Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in- charge. |
| 58 | Made of G.I. wire of dia 4 mm |
| 59 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: |
| 60 | White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests |
| 61 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: |
| 62 | White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps |
| 63 | Providing and fixing kitchen sink including making all connections excluding cost of fittings. |
| 64 | White glazed fire clay sink of size 600x450x250 mm |
| 65 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. |
| 66 | Semi rigid pipei) 32 mm dia |
| 67 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 68 | Providing and fixing soil, waste and vent pipes : |
| 69 | 100 mm diai) Sand cast iron S&S pipe as per IS: 1729 |
| 70 | 75 mm diameter :i) Sand cast iron S&S pipe as per IS: 1729 |
| 71 | Providing and filling the joints with spun yarn, cement slurry and cement mortar 1:2 ( 1 cement : 2 fine sand) in S.C.I./ C.I. Pipes : |
| 72 | 75 mm dia pipe |
| 73 | 100 mm dia pipe |
| 74 | Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. |
| 75 | 100 mm diai) Sand cast iron S&S as per IS - 1729 |
| 76 | 75 mm diai) Sand cast iron S&S as per IS - 1729 |
| 77 | Providing and fixing plain bend of required degree. |
| 78 | 100 mm diai) Sand cast iron S&S as per IS - 1729 |
| 79 | 75 mm diai) Sand cast iron S&S as per IS -1729 |
| 80 | Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. |
| 81 | 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms. |
| 82 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.Internal work - Exposed on wall |
| 83 | 15 mm nominal dia Pipes |
| 84 | Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc.External work |
| 85 | 15 mm dia nominal bore |
| 86 | 25 mm dia nominal bore |
| 87 | Providing and fixing brass stop cock of approved quality : |
| 88 | 15 mm nominal bore |
| 89 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : |
| 90 | 25 mm nominal bore |
| 91 | Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work): |
| 92 | 15 mm nominal bore |
| 93 | 25 mm nominal bore |
| 94 | Providing and placing on terrace (at all floor levels) polyethylene water storagetank,IS : 12701marked,withcoverandsuitablelocking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 95 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : |
| 96 | 15 mm nominal bore |
| 97 | Providing and fixing PTMT soap Dish Holder having length of 138 mm, breadth 102 mm, height of 75 mm with concealed fitting arrangements, weighing not less than 106 gms. |
| 98 | Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : |
| 99 | Inside size 90x80 cm and 45 cm deep including C.I. coverwithframe(lightduty) 455x610mminternal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :i) With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 100 | Constructing soak pit 1.20x1.20x1.20 m filled with brick bats including S.W. drain pipe 100 mm diameter and 1.20 m long complete as per standard design. |
| 101 | Providing and fixing powder coated aluminium work (minimum thickness of powder coating 50 micron) consisting of tee/ angle sections, of approved make conforming to IS : 733 in frames of false ceiling including aluminium angle cleats with necessary C.P. brass/ stainless steel sunk screws, aluminium perimeter angles fixed to wall with stainless steel rawl plugs @ 450 mm centre to centre and fixing the frame work to G.I. level adjusting hangers 6 mm dia. with necessary cadmium plated machine screws all complete as per approved architectural drawings and direction of the Engineer-in-charge (level adjusting hangers, ceiling cleats and expansion hold fasteners to be paid for separately). |
| 102 | Providing and fixing 6 mm dia. G.I. level adjusting hangers (upto 1200 mm length), fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40x3 mm size 60 mm long and stainless steel expandable dash fastener of 12.5 mm dia and 50 mm long, complete as per direction of Engineer- in-charge. |
| 103 | Providing and fixing aluminium hooks and eyes. |
| 104 | 150 mm. |
| 105 | Providing and fixing pre-painted galvalume (PPGL) steel profile sheets AZ-150 of brand Tata Bluescope steel, Everest Industries Ltd., JSW Steel Ltd., Jindal India Ltd. or equalavent(size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with aluminium zinc coating 150 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling / self tapping aluminium screws (Xylan) of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 106 | Providing and fixing pre-painted galvalume (PPGL) steel profile sheets accessories 0.50 mm (+0.05 %) total coated thickness, with aluminium Zinc coating 150 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : of brand Tata Bluescope steel, Everest Industries Ltd., JSW Steel Ltd., Jindal India Ltd. |
| 107 | Ridges plain (500 - 600mm) |
| 108 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade: |
| 109 | New work (two or more coats ) over and including water thinnable primring coat with cement primer. |
| 110 | Applying priming coat: |
| 111 | With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood) |
| 112 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fastners of required dia & length (hold fast lugs or dash fastner shall be paid for separately) : |
| 113 | Superior hard wood category-II. (A) |
| 114 | Providing and fixing 35mm thick panelled or panelled and glazed shutters for doors including ISI marked MS pressed butt hinges with necessary screws with Superior Hard Wood Cat-II(A), Penelling with 12mm thick WPC board all complete as per direction of Engineer-in-charge. |
| 115 | Superior Hard Wood Cat-II(A)i) 35mm thick shutters. |
| 116 | Providing and fixing glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes including black enamelled ISI marked M.S butt hinges with necessary screws. |
| 117 | Kiln seasoned and chemically treated superior hardwood cat-II (A).i) 35 mm thick. |
| 118 | Providing and fixing eaves or facia baord with 18mm thick WPC board 30 cm wide including fixing with nut and bolts etc. complete painting over primer coat of approved shade. |
| 119 | Providing and fixing PVC pipes for drain outlet. |
| 120 | 75 mm dia |
| 121 | Providing cement concrete surface drainwith 1:3:6 (1-cement, 3-sand and 6-graded stone aggregate 40mm nominal size) finished with 1:4 (1-cement & 4-sand) including floating coat of neat cement inside the drain and its top & exposed surface including earth work inexcavation and disposal of surplus earth etc complete. |
| 122 | 15 x 15cm surface drain. |
| 123 | Extra for providing and fixing wind ties of 40x 6mm Aluminium section. |
| 124 | Providing and fixing PVC gully or Nahani Trap including cost of cutting and making good the walls and floors complete |
| 125 | 75mm |
| 126 | Providing and fixingCP Sink cock . (make parry ware or equivalent ) |
| 127 | Providing and laying hollow block cement concrete block walling 200mm thick consisting of hollow block of size 400mm x 200mm x 200mm of mix 1:3:6 (1 cement; 3 coarse sand; 6 graded stone aggregate 10mm nominal size) having a crushing strength of 3.5 N/Sqm at 28 days as per IS:2185 (Part-I) 1979 laid in cement mortar 1:6 (1 cement; 6 coarse sand) upto floor five level. |
| 128 | Providing and laying hollow block cement concrete block walling 100mm thick consisting of hollow block of size 400mm x 100mm x 200mm of mix 1:3:6 (1 cement; 3 coarse sand; 6 graded stone aggregate 10mm nominal size) having a crushing strength of 3.5N/Sqm at 20 days as per IS:2185 (Part-I) 1979 laid in cement mortar 1:6 (1 cement; 6 coarse sand) upto floor five level. |
| 129 | Providing and fixing bolts including nuts and washers complete. |
| 130 | Providing and laying Ceramic glazedfloor tiles (for vision impaired persons as per standards of size 300 x 300mm havingwater absorption less than 0.5% and conforming to IS:15622 of approved make in all colours and shades, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand) including grouting the joints with white cement and matching pigment etc., complete. |
