Tender For Construction Of Permanent Campus At Jnv Hojai Assam
Tender Value
Ref. Documents
Estimated cost
Bid Submission
19 Dec 2025
0 days left
EMD
70.43 Lakhs
Bank guarantee accepted
Document Fee
10000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Hojai → Assam
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Construction Of Permanent Campus At Jnv Hojai Assam
Corrigendum
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 27-Nov-2025 | Clause on Page 8 of Tender Document | Technical Bid | 04-Dec-2025 |
| 2 | 03-Dec-2025 | Extension of Tender | Date | 19-Dec-2025 |
| 3 | 04-Dec-2025 | Corrigendum for Fresh BOQ and New Specifications | Technical Bid | 19-Dec-2025 |
BOQ
| Sl. No. | Item Description |
| 1 | Building Proper |
| 2 | Carriage of excavated material up to 2 km including loading, unloading & stacking |
| 3 | Earthwork in excavation by mechanical means in foundation trenches (all kinds of soil) |
| 4 | Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m…..All kinds of soilPipes, cables etc, not exceeding 80 mm dia. |
| 5 | Filling available excavated earth (excluding rock) in trenches, plinth, sides offoundations etc. in layers not exceeding 20cm in depth,lift upto 1.5 m. |
| 6 | Supplying and filling in plinth with sand under floors, including watering, ramming,consolidating and dressing complete. |
| 7 | Pre-construction anti-termite treatment to top of plinth and wall-floor junction (complete as per IS 6313 Part II) |
| 8 | PCC 1:2:4 (1 Cement : 2 Coarse Sand : 4 Stone Aggregate 20 mm) in foundation & flooring |
| 9 | PCC 1:4:8 (M7.5) in foundations and plinth |
| 10 | PCC 1:2:4 in copings, sills, anchor blocks, etc. |
| 11 | 40 mm thick DPC in 1:2:4 concrete |
| 12 | Extra for waterproofing admixture in concrete |
| 13 | Providing & applying a coat of residual petroleum bitumen of grade of VG-10 ofapproved quality using 1.7kg per square metre on damp proof course… |
| 14 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarsesand : 6 graded stone aggregate 20 mm nominal size) ….. |
| 15 | PCC 1:2:4 coping over parapet wall (avg 75 mm × 230 mm) |
| 16 | RCC 1:1.5:3 (M20) in columns, beams, slabs, lintels, foundations, etc. excluding centering, shuttering |
| 17 | Centering and shuttering including strutting, propping etc. and removal of form for all heights: :Foundations, footings, bases of columns, etc. for mass concrete |
| 18 | Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. |
| 19 | Columns, Pillars, Piers, Abutments, Posts and Struts |
| 20 | Extra for shuttering in circular work (20% of respective centering and shuttering items) |
| 21 | Small lintels not exceeding 1.5 m clear span, moulding as in cornices, window sills, string courses, bands, copings, bed plates, anchor blocks and the like |
| 22 | Edges of slabs and breaks in floors and wallsUnder 20 cms wide |
| 23 | Suspended floors, roofs, landings, balconies and access platform. with water proof ply 12 mm thick |
| 24 | Lintels, beams, plinth beams, girders, bressumers and cantilevers. with water proof ply 12 mm thick |
| 25 | Columns, Pillars, Piers, Abutments, Posts and Struts |
| 26 | Small lintels not exceeding 1.5 m clear span, moulding as in cornices, window sills, string courses, bands, copings, bed plates, anchor blocks and the like |
| 27 | Edges of slabs and breaks in floors and wallsUnder 20 cms wide |
| 28 | Suspended floors, roofs, landings, balconies and access platform. with water proof ply 12 mm thick |
| 29 | Reinforcement Fe-500D up to plinth level |
| 30 | Reinforcement Fe-500D above plinth level |
| 31 | Aluminium fluted sheet covering over expansion joint, 200 mm |
| 32 | Add for plaster drip/groove to RCC projections |
| 33 | Providing and fixing sheet covering over expansion joints with iron screws as per designAluminium fluted strips 3.15 mm thick.200 mm wide |
| 34 | RCC M25 (machine batched) up to & above plinth level, incl. pumping & admixtures |
| 35 | Design mix M-25 RCC above plinth to floor V level |
| 36 | Add for using extra cement in the items of design mix over and above the specifiedcement content therein. |
| 37 | Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer. M.S. tube |
| 38 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 39 | Half brick masonry with common burnt clay F.P.S. (non modular) brick of classdesignation 7.5 in foundations and plinth in : cement mortar 1:4 (1 cement : 4 coarse sand) |
| 40 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in: |
| 41 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.Cement mortar 1:4 (1 cement :4 coarse sand) |
| 42 | Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry. |
| 43 | Brick edging 7cm wide 11.4 cm deep to plinth protection with common burnt clayF.P.S. (non modular) bricks of class designation 7.5 including grouting with cement mortar 1:4 (1 cement : 4 fine sand). |
| 44 | 18 mm marble (RNP/Udaipur/Black) slabs >0.5 sqm on 20 mm CM 1:4 |
| 45 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters…a) Granite of any colour and shade Area of slab over 0.50 sqm |
| 46 | Providing edge moulding to 18 mm thick marble stone counters, Vanities etc.,including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.a) Marble work |
| 47 | Edge moulding & polish — granite |
| 48 | Extra for fixing marble/granite stone, over and above corresponding basic item … complete. |
| 49 | Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter… |
| 50 | Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick fixed in urinal partitions … Engineer-in- charge.Granite Stone of approved shade |
| 51 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wroght framed and fixed in position with hold fast….(hold fast lugs or dash fastener shall be paid for seperately)Second class teak wood |
| 52 | Extra for providing frosted glass panes 4 mm thick instead of ordinary float glass panes 4 mm thick in doors…(Area of opening for glass panes excluding portion inside rebate shall be measured). |
| 53 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, ……25 mm thick (for cupboard) including ISI marked nickel plated bright finished M.S. Piano hinges IS : 3818 marked with necessary screws |
| 54 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type… 35 mm thick including ISI marked Stainless Steel butt hinges with necessaryscrews. |
| 55 | Extra for providing lipping with 2nd class teak wood battens 25 mm ...(over all areaof door shutter to be measured). |
| 56 | Extra for cutting rebate in flush door shutters (Total area of the shutter to bemeasured). |
| 57 | Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of avg width…35mm thick shutters. Kiln seasoned and chemically treated hollock wood |
| 58 | Providing and fixing M.S. grills of required pattern in frames of windows etc…Fixed to steel windows by welding |
| 59 | Providing and fixing fly proof galvanized M.S. wire gauge to windows and clerestory windows……..With 12 mm mild steel U beading |
| 60 | Providing and fixing ISI marked oxidised M.S. single acting spring hinges with necessary screws etc. complete :150 mm |
| 61 | Providing and fixing oxidised M.S. hasp and staple (safety type) conforming to IS : 363 with necessary screws etc. complete :90 mm |
| 62 | Providing and fixing oxidised M.S. casement stays (straight peg type) with necessary screws etc. complete.250 mm weighing not less than 150 gms |
| 63 | Providing and fixing special quality bright finished brass cupboard or ward robe locks with four levers of approved quality including necessary screws etc. complete.75 mm |
| 64 | Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868)..250x16 mm |
| 65 | Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868)..300x16 mm |
| 66 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coatingnot less than grade AC 10 as per IS : 1868 ).a) 250x10 mm |
| 67 | b) 200x10 mm |
| 68 | c) 300x10 mm |
| 69 | d) 150x10 mm |
| 70 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :a) 125 mm |
| 71 | Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868)..Twin rubber stopper |
| 72 | Providing and fixing aluminium casement stays, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. |
| 73 | Providing and fixing wooden moulded corner beading of triangular shape to the junction of panelling etc. 2nd class teak wood.50x50 mm (base and height) |
| 74 | Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss..1.5 mm thick |
| 75 | Providing and fixing cup board shutters with 25 mm thick veneered particle board IS: 3097 marked,…..With decorative veneering on one side and commercial veneering on other side |
| 76 | Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S……Using M.S. angles 40x40x6 mm for diagonal braces |
| 77 | Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length andIS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters.80x1.25 mm M.S. laths with 1.25 mm thick top cover |
| 78 | Providing and fixing ball bearing for rolling shutters. |
| 79 | Extra for providing mechanical device chain and crank operation forExceeding 10.00 sqm and upto 16.80 sqm in the area |
| 80 | Extra for providing grilled rolling shutters manufactured out of 8 mm dia M.S. bar instead of laths as per design approved by Engineer-in- charge, (area of grill to be measured). |
| 81 | Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators, side /top /centre hung, etc....a) Fixing with 15x3 mm lugs 10 cm long embedded in c.c block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) |
| 82 | Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections….Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block15x10x10 cm of C.C. 1:3:6 |
| 83 | Providing and fixing M.S. Tubular frames for doors, windows, ventilators and cupboard with rectangular/ L-Type sections,…..Fixing with 15x3 mm lugs 10 cm long embedded in C.C block 15x10x10 cm of C.C.1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) |
| 84 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc. including cutting, hoisting…(a). Electrical resistance or induction welded tubes |
| 85 | Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fanclamp, of internal dia 140 mm, 73 mm height.. |
| 86 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing…In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works |
| 87 | Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with :4.0 mm thick glass panes |
| 88 | Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate)…40 mm thick with 20 mm nominal size stone aggregate |
| 89 | 52 mm thick cement concrete flooring with concrete hardener topping, under layer 40 mm thick cement concrete 1:2:4... excluding the cost of nosing of steps etc. complete. |
| 90 | Cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement. 18mm thick |
| 91 | Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. |
| 92 | Ordinary cement without any pigment |
| 93 | Marble stone flooring with 18 mm thick marble stone, as per sample of marble approved by Engineer-in-charge…Raj Nagar plain |
| 94 | Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with …25 mm thick. |
| 95 | Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand).. |
| 96 | Extra for pre finished nosing in treads of steps of Kota stone/ sand stone slab. |
| 97 | Extra for Kota stone/ sand stone in treads of steps and risers using single length upto 1.05 metre. |
| 98 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622(thickness to be specified by the manufacturer).. |
| 99 | 60 mm M30 interlocking paver blocks incl. 50 mm sand bed |
| 100 | Chequered PCC tiles 22 mm on 20 mm CM 1:4 (medium shade) |
| 101 | Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer)... skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand)…Size of Tile 600x600 mm |
| 102 | Chequered terrazzo tiles 22 mm (medium shade) on 20 mm CM 1:4 |
| 103 | Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mmnominal size) over .. |
| 104 | Providing & fixing precoated galvanized (PPGL/Galvalume) profile roofing sheets 0.50 mm TCT fixed to purlins with self-drilling screws, including overlaps, cutting & wastage complete |
| 105 | Providing and fixing precoated galvanised steel sheet roofing accessories of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05 mm) with Zinc coating 120gram per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete :Precoated GI gutters (approx. 600 mm girth) with joints & brackets complete (two eaves; ≈ 82 m) |
| 106 | Precoated GI barge boards, up to 300 mm girth (gable ends; ≈ 90 m) |
| 107 | Precoated GI ridge/valley 500 mm girth (single ridge ≈ 42 m) |
| 108 | uPVC (SN-4) rainwater pipes 160 mm dia, with specials & clamps (8 downpipes × ~7 m ≈ 56 m) |
| 109 | uPVC bends/shoes for 160 mm pipes |
| 110 | uPVC moulded fitting – Bend 87.5°, 110 mm |
| 111 | uPVC moulded fitting – Shoe (Plain) 110 mm |
| 112 | Providing & fixing uPVC pipe clips, with hardwood plugs & CM 1:4 making good – 110 mm |
| 113 | Cast iron grating for inlet mouth of rain water pipe, 15 cm dia, ≥440 g |
| 114 | 12 mm thick cement plaster of mix 1:6 (1 cement:6 fine sand) |
| 115 | 15 mm cement plaster 1:6 (rough side of wall) |
| 116 | 12 mm cement plaster 1:6 (1 cement : 6 coarse sand) |
| 117 | 15 mm cement plaster on rough side of single/half-brick wall 1:6 |
| 118 | 18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1cement : 5 coarse sand)………. |
| 119 | Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement.20 mm cement plaster |
| 120 | 6 mm cement plaster 1:3 (1 cement : 3 fine sand) |
| 121 | Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. |
| 122 | White washing with lime to give an even shade: New work (three or more coats) |
| 123 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade :New work (two or more coats) over and including water thinnable priming.. |
| 124 | Finishing walls with textured exterior paint of required shade :New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including… |
| 125 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade:New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including primingcoat of exterior primer applied @ 2.20 kg/10 sqm) |
| 126 | Applying priming coat:a) With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood) |
| 127 | b) With ready mixed red oxide zinc chromate primer of approved brand andmanufacture on steel galvanised iron/ steel works |
| 128 | c) With ready mixed red oxide zinc chromate primer of approved brand andmanufacture onsteel works (second coat) |
| 129 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :Two or more coats on new work |
| 130 | Finishing walls with Acrylic Smooth exterior paint of required shade :New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) |
| 131 | Painting with black anti-corrosive bitumastic paint of approved brand and manufacture to give an even shade :Two or more coats on new work |
| 132 | Providing and applying white cement basedputty of average thickness 1mm of approved brand and manufacturer… |
| 133 | Distempering with 1st quality acrylic distemper, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre…… even shade and colour.Two coats |
| 134 | Providing and placing in position 100 mm thick factory made machine batched & machine mixed Precast RCC Rectangular Covers on drains of footpath of various sizes, of M-25 grade cement concrete for RCC all complete as per direction of Engineer-in-Charge. |
| 135 | Providing and fixing chain-link fencing of required width, 4 mm dia wire mesh with MS angle posts embedded in cement concrete blocks |
| 136 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections…For fixed portionAnodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) |
| 137 | For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots..Anodised aluminium (anodised transparent or dyed to required shade according toIS: 1868, Minimum anodic coating of grade AC 15) |
| 138 | Providing and fixing glazing in aluminium door, window, ventilator shutters …With float glass panes of 5.50 mm thickness |
| 139 | Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, etc.complete as per the direction of Engineer-in-charge. |
| 140 | Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather..Upto 5mm depth and 5 mm width |
| 141 | Providing and fixing 12 mm thick prelaminated particle board flat pressed three.. with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer-in-charge.Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side |
| 142 | Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of:(i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface.(ii) IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface.(iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area.(iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheetshould be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/ sqm). |
| 143 | Providing and laying integral cement based water proofing treatment including preparation of surface..(a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645…(b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5..(c) After two days of proper curing applying a second coat of cement slurry using2.75 kg/ sqm of cement admixed with…(d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with…(e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test…(a) With average thickness of 120 mm and minimum thickness at khurra as 65 mm. |
| 144 | Providing and laying cinder filling in sunken floors and other locationswith approved quality cinder including watering and light ramming etc.required for proper compaction/completion of the work complete in all respects as per drawingsand as directed by the Engineer in Charge. |
| 145 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :150 mm |
| 146 | Providing and fixing aluminium door buffer of approved make, design and colour with necessary screws etc all complete as directed and specified by the Engineer-in Charge : |
| 147 | Roller blinds – black-out fabric |
| 148 | Providing and laying 1st quality ceramic glazed Anti skid floortiles of size 300x300 mm (thickness to be specified by the manufacturer) conforming to IS:15622 in all colours, shades, sizes as approved over 20 mm thick bed of Cement Mortar 1: 4 (1 cement : 4 Coarse Sand) including pointing the joints with white cement and matching pigment etc all complete in all respect as per specification/drawings and as directed and specified by the Engineer-in-Charge. |
| 149 | 0.47 mm Galvalume sheet roofing incl. fasteners |
| 150 | G.I. frame work for suspended false ceiling |
| 151 | Providing and fixing false ceiling at all heights ….12 mm plain gypsum board ceiling incl. finishing |
| 152 | DEVELOPMENT WORKS |
| 153 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed — all kinds of soil |
| 154 | Banking excavated earth in layers not exceeding 20 cm in depth, breaking clods, watering, rolling each layer with ½ tonne roller or wooden/steel rammers, and rolling every 3rd and top-most layer with power roller of minimum 8 tonnes and dressing up, in embankments for roads, flood banks, marginal banks, and guide banks etc., lead upto 50 m and lift upto 1.5 m – all kinds of soil |
| 155 | Earth work in excavation by mechanical/manual means in foundation trenches/drains (≤1.5 m wide/10 sqm), incl. dressing, ramming; lift 1.5 m; lead 50 m — All kinds of soil |
| 156 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m – Quantity of filling @ 35 % |
| 157 | Excavating, supplying and filling of local earth (including royalty) by mechanical transport up to a lead of 5 km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete |
| 158 | Extra for every additional lift of 1.5 m in excavation/banking excavated or stacked material – All kinds of soil (1.5 m to 3.0 m). |
| 159 | Extra for every additional lift of 3.0 m to 3.5 m in excavation/banking excavated or stacked material. |
| 160 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil. |
| 161 | Earthwork in all kinds of soil up to 3.0 m depth |
| 162 | Earthwork in all kinds of soil up to 4.5 m depth |
| 163 | Earthwork in all kinds of soil (4.5–6.0 m) |
| 164 | Earthwork up to 4.5 m depth (other reach) |
| 165 | Earthwork 1.5 – 3.0 m (all kinds of soil) |
| 166 | Earthwork 1.5 – 3.0 m (ordinary rock) |
| 167 | Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/or good earth to be paid separately) – Quantity of filling @ 50 % |
| 168 | Earthwork in excavation (ordinary rock) |
| 169 | Excavating trenches for pipes/cables in all kinds of soil; pipes/cables exceeding 80 mm but not exceeding 300 mm dia |
| 170 | Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating, and dressing complete. |
| 171 | Supply of chemical emulsion for anti-termite treatment |
| 172 | Anti-termite treatment (Chlorpyriphos/Lindane 20% EC @1% conc.) |
| 173 | Damp-proof course 40 mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone III) : 4 graded stone aggregate 12.5 mm nominal size) |
| 174 | CC 1:2:4 |
| 175 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering – All work up to plinth level (1:4:8 – 1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) |
| 176 | Providing and laying in position cement concrete 1:5:10 (1 cement : 5 coarse sand (zone-III) : 10 graded stone aggregate 40 mm nominal size) derived from natural sources, excluding centering and shuttering, all work up to plinth level |
| 177 | Extra for providing and mixing water-proofing material in cement concrete work in doses by weight of cement as per manufacturer’s specification |
| 178 | Providing and applying a coat of residual petroleum bitumen of grade VG-10 of approved quality using 1.7 kg per sqm on damp proof course after cleaning the surface with brushes and finally wiping with cloth lightly soaked in kerosene oil |
| 179 | Centering & shuttering for walls/retaining walls etc., incl. strutting & propping, removal of formwork |
| 180 | RCC 1:1.5:3 in beams/landings etc. |
| 181 | Centering and shuttering including strutting, propping etc. and removal of form for all heights – Foundations, footings, bases of columns, etc., for mass concrete |
| 182 | Centering & shuttering for slabs/lintels |
| 183 | Centering & shuttering for suspended floors/landings |
| 184 | Centering & shuttering for shelves (cast in situ) |
| 185 | Centering and shuttering for columns, pillars, piers, abutments, posts and struts. |
| 186 | Extra for centering & shuttering for additional height over 3.5 m |
| 187 | Edges of slabs & breaks (<20 cm) |
| 188 | Centering & shuttering for slabs |
| 189 | Centering and shuttering for lintels, beams, plinth beams, girders, bressumers, and cantilevers with water-proof ply 12 mm thick. |
| 190 | Tie bolt with spring coil & plastic cone |
| 191 | Steel reinforcement for RCC |
| 192 | Steel reinforcement (alt. item) |
| 193 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete up to plinth level – Thermo-Mechanically Treated bars of grade Fe-500D or more |
| 194 | Steel reinforcement for R.C.C. work above plinth level (Fe-500D or more). |
| 195 | R.C.C. work in Footing, concrete of M25 grade (330 kg/cum) |
| 196 | R.C.C. work in Beam (above plinth level up to floor V) |
| 197 | Add for extra cement in RCC M-25 |
| 198 | Brick work with common burnt clay F.P.S. (non-modular) bricks of class 7.5 in foundation and plinth in cement mortar 1:6. |
| 199 | Brick work with common burnt clay F.P.S. (non-modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in cement mortar 1:6 (1 cement : 6 coarse sand) |
| 200 | Brick work with common burnt clay F.P.S. (non-modular) bricks of class 7.5 in superstructure above plinth level up to floor V level, in cement mortar 1:6. |
| 201 | Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) up to plinth level with cement mortar 1:6 (1 cement : 6 coarse sand) |
| 202 | Granite 18 mm (area of slab >0.50 sqm) incl. bedding, polishing, etc. |
| 203 | Edge moulding to 18 mm granite, machine polished |
| 204 | Extra for fixing marble/granite in facia/drops (≤150 mm) with epoxy |
| 205 | M.S. grills fixed to steel windows by welding, incl. primer |
| 206 | Aluminium sliding door bolt, anodised AC-10 — 300×16 mm |
| 207 | Aluminium tower bolt, anodised AC-10 — 300×10 mm |
| 208 | Aluminium tower bolt, anodised AC-10 — 150×10 mm |
| 209 | Aluminium handle, anodised AC-10 — 125 mm |
| 210 | Aluminium hanging floor door stopper, anodised AC-10 — twin rubber |
| 211 | Aluminium casement stay, anodised AC-10 |
| 212 | Structural steel work in built-up sections/trusses/framed work incl. primer |
| 213 | Steel work in tubular sections with 15×3 mm lugs, 10 cm long (incl. priming) |
| 214 | Steel work welded in built-up sections/framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel, etc., as required – In gratings, frames, guard bars, ladders, railings, brackets, gates & similar works |
| 215 | Providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates, etc., including welding, grinding, buffing, polishing and fixing with necessary fasteners, bolts, and accessories. |
| 216 | Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate), 40 mm thick with 20 mm nominal stone aggregate, finished with floating coat of neat cement and cement slurry |
| 217 | 52 mm cement concrete floor with hardener |
| 218 | Kota stone slab flooring over 20 mm thick base, laid and jointed with grey cement slurry, base mortar 1:4. |
| 219 | Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm thick cement mortar 1:3, jointed with grey cement slurry and polished. |
| 220 | Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS:15622 in skirting, risers, dados etc., in CM 1:3, jointed with grey cement slurry (3.3 kg/sqm) and white cement pigment. |
| 221 | Providing and laying 1st quality ceramic glazed floor tiles 300×300 mm in CM 1:4, jointed with grey cement slurry (3.3 kg/sqm) and white cement pigment. |
| 222 | Pre-coated GI profile sheets 0.50 mm (Z-120), fixed with self-drilling screws |
| 223 | Roofing accessories — Gutter (600 mm overall girth), pre-coated GI |
| 224 | 12 mm cement plaster 1:6 (rough side) |
| 225 | 15 mm cement plaster in CM 1:4 on rough side of wall |
| 226 | 15 mm cement plaster on rough side of wall, mix 1:6 (1 cement:6 coarse sand). |
| 227 | 12 mm cement plaster finished with floating coat of neat cement (1:4 mix, 1 cement : 4 fine sand) on brick surface |
| 228 | Providing and applying white cement-based putty of average thickness 1 mm, of approved brand, over plastered surface for smooth finish. |
| 229 | 6 mm cement plaster 1:3 on brick wall |
| 230 | Plaster of Paris putty 2 mm |
| 231 | Finishing walls with water proofing cement paint of required shade: new work (two or more coats @3.84 kg/10 sqm). |
| 232 | Finishing walls with textured exterior paint of required shade – New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm |
| 233 | Premium Acrylic Smooth exterior paint (two or more coats over primer) |
| 234 | Priming coat on steel work with red oxide zinc chromate primer |
| 235 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade – New work (two or more coats) |
| 236 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade – Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture |
| 237 | Preparation and consolidation of subgrade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the subgrade and disposal of surplus earth with lead upto 50 metres |
| 238 | Supplying and stacking at site – 63 mm to 45 mm size stone aggregate |
| 239 | Supplying and stacking at site – 53 mm to 22.4 mm size stone aggregate |
| 240 | Supplying and stacking at site – Stone screening 13.2 mm nominal size (Type A) |
| 241 | Supplying and stacking at site – Stone screening 11.2 mm nominal size (Type B) |
| 242 | Supplying and stacking at site – Red Bajri |
| 243 | Supplying and stacking at site – Moorum |
| 244 | Laying, spreading and compacting stone aggregate of specified sizes to WBM specifications in uniform thickness, hand-picking, rolling with 3-wheeled road/vibratory roller 8–10 tonne capacity in stages to proper grade and camber, applying and brooming requisite type of screening/binding material to fill up interstices of coarse aggregate, watering and compacting to the required density. |
| 245 | Supplying at site angle iron post & strut of required size including bottom to be split and bent at right angle in opposite direction for 10 cm length and drilling holes up to 10 mm dia etc. complete |
| 246 | Extra for providing & mixing hardening compound in cement concrete (as per manufacturer’s spec.) |
| 247 | Providing & laying bitumen hot sealing compound for expansion joints (Grade A) – 5 cm × 5 cm |
| 248 | Road surface marking with ready mixed road marking paint, two or more coats on bituminous surface |
| 249 | Providing & fixing glow studs 100×20 mm with retro-reflective panels, fixed with approved adhesive |
| 250 | Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length (total length 90 m), having 50 nos rounds per 6 metre length, up to 3 m height of wall with existing angle iron \"Y\" shaped placed 2.4 m or 3.0 m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal, including necessary bolts or G.I. barbed wire tied to angle iron, with reinforced barbed tape (R.B.T.) / spring core (2.5 mm thick) wire of high tensile strength of 165 kg/sq.mm with tape (0.52 mm thick) and weight 43.478 gm/meter (cost of M.S. angle, C.C. blocks shall be paid separately) |
| 251 | Retro-reflective overhead informatory road signage boards (2 mm Al sheet with Type-III sheeting), complete |
| 252 | 2.5 mm thermoplastic retro-reflective road marking strips by automatic applicator, complete |
| 253 | Kerb channel 30 cm wide, 50 mm thick in CC 1:3:6 over 75 mm brick ballast bed, finished smooth |
| 254 | Providing and laying 60 mm thick factory made cement concrete interlocking paver block of M-30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with fine sand etc., all complete as per the direction of Engineer-in-Charge |
| 255 | Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 Cement : 3 coarse sand), including making joints with or without grooves, making drainage openings wherever required, complete as per direction of Engineer-in-Charge. (Precast C.C. kerb stone shall be approved by Engineer-in-Charge) |
| 256 | Providing and laying C.C. pavement of mix M-25 with ready mixed concrete from batching plant. The ready mixed concrete shall be laid and finished with screed board vibrator, vacuum dewatering process and finally finished by floating, brooming with wire brush etc., complete as per specifications and directions of Engineer-in-charge. (Panel shuttering work paid separately) |
| 257 | Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves, drainage opening wherever required, complete as directed by Engineer-in-charge (Precast C.C. kerb stone) |
| 258 | 100 mm CI spun iron S&S pipe (IS 3989) |
| 259 | Terminal guard for 100 mm CI pipe |
| 260 | G.I. pipe, 32 mm dia (external work) |
| 261 | G.I. pipe, 40 mm dia |
| 262 | G.I. pipe, 50 mm dia |
| 263 | G.I. pipe, 65 mm dia |
| 264 | G.I. pipe, 80 mm dia |
| 265 | Painting G.I. pipe, 32 mm dia |
| 266 | Painting G.I. pipe, 40 mm dia |
| 267 | Painting G.I. pipe, 50 mm dia |
| 268 | Painting G.I. pipe, 65 mm dia |
| 269 | Painting G.I. pipe, 80 mm dia |
| 270 | Sand filling around G.I. pipe, 32 mm |
| 271 | Sand filling around G.I. pipe, 40 mm |
| 272 | Sand filling around G.I. pipe, 50 mm |
| 273 | Sand filling around G.I. pipe, 65 mm |
| 274 | Sand filling around G.I. pipe, 80 mm |
| 275 | C.I. double acting air valve, 50 mm |
| 276 | C.I. double acting air valve, 80 mm |
| 277 | Gun metal gate valve, 20 mm (screwed end) |
| 278 | Gun metal gate valve, 25 mm |
| 279 | Gun metal gate valve, 32 mm |
| 280 | Gun metal gate valve, 40 mm |
| 281 | Gun metal gate valve, 50 mm |
| 282 | Gun metal gate valve, 65 mm |
| 283 | Gun metal gate valve, 80 mm |
| 284 | Masonry gate valve chamber (30×30×50 cm) with FPS bricks 7.5 |
| 285 | Masonry water-meter chamber (60×45×50 cm) with FPS bricks 7.5 |
| 286 | G.I. Union, 25 mm |
| 287 | G.I. Union, 32 mm |
| 288 | G.I. Union, 40 mm |
| 289 | G.I. Union, 50 mm |
| 290 | G.I. Union, 65 mm |
| 291 | G.I. Union, 80 mm |
| 292 | Manhole cover 455×610 mm with frame (light duty) |
| 293 | Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar 1:2 (1 cement : 2 fine sand) including testing of joints, etc., complete — 450 mm dia R.C.C. pipe |
| 294 | Constructing brick masonry manhole (90×80×45 cm) with RCC slab, plastering, channels etc.; with FPS bricks class 7.5 and light duty CI cover |
| 295 | Extra depth for manhole size 90×80 cm; with FPS bricks class 7.5 |
| 296 | Brick masonry circular manhole (0.91 m dia bottom, 0.56 m top) 0.91 m deep with HD-20 SFRC cover & frame; with FPS bricks class 7.5 |
| 297 | Extra depth for circular manholes 0.91 m dia beyond 0.91 m to 1.67 m; with FPS bricks class 7.5 |
| 298 | Providing & fixing square mouth S.W. gully trap SP-1, 180×150 mm “P” type with brick masonry chamber & watertight CI cover; with FPS bricks class 7.5 |
| 299 | M.S. foot rests in manholes (20×20×10 cm CC 1:3:6; 20×20 mm sq. bar) |
| 300 | Orange colour plastic encapsulated foot rest |
| 301 | RCC MH cover & frame LD-2.5, 600×450 mm |
| 302 | RCC MH cover & frame HD-20, 560 mm dia |
| 303 | Soak pit 2.5 m dia × 3.0 m deep (honey-comb shaft) |
| 304 | Providing and placing PVC water stops (IS:12200) for RCC joints – serrated with central bulb, 225 mm wide, 8–11 mm thick. |
| 305 | Providing and applying integral crystalline slurry waterproofing on vertical RCC surfaces (two coats @ 0.70 kg/sqm/coat). |
| 306 | Providing and applying integral crystalline slurry waterproofing on horizontal RCC surfaces (one coat @ 1.10 kg/sqm). |
| 307 | Drilling through rocky strata incl. boulders (300 mm) |
| 308 | Boring/drilling for casing/strainer pipe up to 90 m depth – 400 mm dia, all types of soil |
| 309 | Boring/drilling beyond 90 m & up to 150 m – 400 mm dia, all types of soil |
| 310 | PVC well screen pipe 150 mm (IS:12818) |
| 311 | Stone boulders 5–20 cm in recharge pit |
| 312 | Gravel 5–10 mm in recharge pit |
| 313 | Coarse sand 1.5–2.0 mm in recharge pit |
| 314 | Gravel packing in tubewell (IS 4097) |
| 315 | ERW FE-410 M.S. casing pipe 200 mm dia, min. 5.40 mm wall, including painting & accessories |
| 316 | ERW FE-410 plain-slotted pipe 200 mm dia, min. 5.40 mm wall, including painting & accessories |
| 317 | Development of tubewell with compressor, testing & disinfection |
| 318 | Mild steel threaded cap / plate for borewell – 200 mm |
| 319 | M.S. clamp for casing/housing pipe – 200 mm |
| 320 | Bail / bottom plug – 200 mm |
| 321 | Acrylic Flooring (8 Layer System) — including 1 layer resurfacer, 5 layers cushion, 2 layers colour, line marking as per international standards |
| 322 | Hand Operated Hydraulic Moveable Basketball System with 20 mm thick transparent acrylic board, aluminium anodized frame, dunking rims, non-marking wheels, and hydraulic lifting system as per BFI specifications – complete set |
| 323 | Handball Goal Post Poles (moveable) – 3 m width × 2 m height, made of M.S. Pipe 80 mm dia (3.2 mm thick) with rear pipes, hooks, wheels and heavy-duty net – complete set |
| 324 | Volleyball Poles (Basic model) with overlapping system for height adjustment, including plastic coated steel wire net and fiberglass antenna – complete set |
| 325 | Volleyball Poles (Basic model) with overlapping system for height adjustment, including plastic coated steel wire net and fiberglass antenna – complete set |
| 326 | Line marking of Badminton Court on Kota stone flooring as per international rules with paint (Asian / Berger or equivalent) |
| 327 | Installation Charges for sports equipment and fixtures |
| 328 | Chain Link Fencing (3.0 m high) – including posts, supports and all fixtures |
| 329 | Supply & fixing HDPE double wall corrugated pipe IS 16098 (Part-2) for underground drainage incl. specials, re-excavation & refilling; 200 mm dia |
| 330 | Borewell submersible pumping set (15 HP approx., 15000 L/h @ 250 m head) incl. cable, panel, uPVC riser, fittings & clamps – complete |
| 331 | 65 mm G.I. pipe with fittings, supports & two coats enamel paint |
| 332 | Outdoor weather-proof plumbing panel with MCCB, metering, SPD, bus-bar, MCBs; supply, fixing, testing & commissioning |
| 333 | 125 micron polythene sheet (7 sqm/kg) |
| 334 | HORTICULTURE |
| 335 | Trenching in ordinary soil up to a depth of 60 cm including removal and stacking of serviceable materials and disposal of surplus soil, spreading and leveling, refilling with earth mixed with sludge/manure before and after flooding. |
| 336 | Supplying and stacking sludge at site including royalty and carriage up to 5 km lead (measured in stacks reduced by 8% for payment). |
| 337 | Supplying and stacking dump manure from approved source including carriage up to 5 km (reduced by 8% for payment). |
| 338 | Mixing earth and sludge/manure in required proportion as directed by Officer-in-Charge. |
| 339 | Grassing with Doob grass in rows 5 cm apart in both directions, including watering and maintenance for 30 days or more. |
| 340 | Uprooting rank vegetation and weeds, digging area to 60 cm depth, removing roots, flooding, fine dressing for new grass, disposal of rubbish. |
| 341 | Preparation of beds for hedging and shrubbery by excavating 60 cm deep, refilling with earth and sludge/manure (8:1), flooding and dressing. |
| 342 | Digging holes in ordinary soil and refilling with excavated earth mixed with manure/sludge (2:1), flooding with water, dressing, removing surplus earth. |
| 343 | Edging with bricks laid dry lengthwise, excavation, refilling, consolidating with hand packing and neat dressing. |
| 344 | Flooding the ground with water including making kiaries and dismantling the same. |
| 345 | Providing and watering of irrigation water through water tanker (5000 L), including cost of water, filling, and site watering, as per direction. (30 trips in 3 months at 3-day intervals) |
| 346 | Plantation of Trees, Shrubs, and Hedge at site including watering and removal of unserviceable materials (Hedge Plant/Ground cover). |
| 347 | Providing and stacking of Cassia fistula (Amaltash) of height 120–135 cm in big poly bags (25 cm). |
| 348 | Providing and stacking of Hibiscus rosasinensis of height 45–60 cm with 3–4 branches in earthen pots (20 cm). |
| 349 | Providing and stacking of Delonix regia (Gulmohar) of height 150–165 cm in big poly bags (25 cm). |
| 350 | Supply and stacking of Azadirachta indica (Neem) plant of height 120–130 cm in big poly bags (25 cm). |
| 351 | Providing and stacking of Bottle palm of height 210–240 cm, bottom girth 30–35 cm, in big HDPE bags. |
| 352 | Providing and stacking of Foxtail palm of height 240–270 cm, bottom girth 35–40 cm, in big HDPE bags. |
| 353 | Providing and stacking of Mangifera indica (Mango grafted) height 60–75 cm in big poly bags (25 cm). |
| 354 | Providing and stacking of Michelia champa (Golden Champa) height 90–105 cm in earthen pots (25 cm). |
| 355 | Providing and stacking of Peltophorum species height 150–165 cm in big poly bags (25 cm). |
| 356 | Providing and displaying Marigold Jaffri French orange/yellow/Russet, 60–75 cm height, 60–75 flowers, in 30 cm pot. |
| 357 | Providing and stacking of Spider plant (Chlorophytum comosum). |
| 358 | Providing and stacking of Lemon tree. |
| 359 | Providing and stacking of Banana tree. |
| 360 | Providing and fixing of Precast RCC Garden Bench including all labour, T&P etc. complete. |
| 361 | Laying of watering/sprinkler pipe along garden, making outlet points and providing 2 hose pipes for new lawn/garden. |
| 362 | INTERNAL WATER SUPPLY AND SANITARY WORKS |
| 363 | Providing & fixing stone slab table rubbed, edges rounded and polished of size 75 X 50cm deep and 1.8 cm thick fixed in urinal patitions by cutting chase of appropriate width with chase cutter and embedding the stone in chase with epoxy grout or with cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregste 6mm nominal size) as per Engineer-in-charge and finished smooth White Agaria Marble Stone |
| 364 | Providing and fixing Salem Stainless Steel A ISI 304 (18/8) kitchen sink as per IS: 13983 with CI brackets and stainless steel waste with plug 40mm including painting of fittings and brackets, cutting and making good the walls wherever required. Kitchen sink with drain board 510X1040mm bowl depth 200mm. |
| 365 | Sink without drain board 610X510 mm bowl depth 200mm. |
| 366 | Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : 17.32.1) Rectangular shape 453x357 mm |
| 367 | Providing and fixing toilet paper holder : 17.34.1) C.P. brass |
| 368 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid |
| 369 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS: 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : White Vitreous china Orissa pattern W.C. pan of size 580x440 mm withintegral type foot rests |
| 370 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in-charge |
| 371 | Providing and fixing PTMT Bottle Trap for Wash basin and sink. Bottle trap 38 mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms.(sink & urinal) |
| 372 | Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour weighing not less than 105 gms. |
| 373 | Providing and fixing PTMT towel rail complete with brackets fixed wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.600 mm long towel rail with total length of 645 mm, width 78 mm andeffective height of 88 mm, weighing not less than 190 gms |
| 374 | Providing and fixing CP Brass shower rose with 15 or 20 mm inlet100 mm diameter |
| 375 | Providing & fixingPTMT towel ring trapezoidal shape 215 mm long 200 mm wide with minimum distance of 37 mm from wall face with concealedfittingsarrangement of approved quality and colour weighing not less than 88 gms |
| 376 | Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge. a) 15 mm nominal dia. |
| 377 | Providing and fixing uplasticised PVC connection pipe with brass unions 45 cm length15 mm nominal bore |
| 378 | Providing and fixing C.P. brass bib cock of approved quality confirming to IS:8931 15mm nominal bore |
| 379 | Providing and fixing C.P.brass angle valve for basin mixer and geyser points of approved quality conforming to IS 8931 a) 15 mm nominal bore. |
| 380 | Providing and fixing wash bashin with C.I. brackets, 15mm dia cp brass singal hole basin mixer of approved quility and make, including painting of fittings and brackets, cutting and making good the walls wherever required -a) White vitreous china wash basin size 550x400 mm with a 15 mm cp brass singal hole basin mixer. |
| 381 | Providing & fixing PVC waste pipe for sink oncluding PVC waste fitting Complete Flexible Pipe 32mm Dia |
| 382 | Providing and fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P brass waste and 40mm C.P. brass trap with necessary C.P. brass unions complete, including painting of fittings and brackets, cutting and making good the wall wherever required :Size 450x300x150 mm |
| 383 | Providing and fixing MS holder bat clamps of approved design to cast iron (spun) pipe embedded in and Including cement concrete blocks 10 x10 x10cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) including cost of cutting holes and making good the walls etc. For 100mm dia. Pipe |
| 384 | Providing and fixing PTMT grating of approved quality and colour Circular type125 mm nominal dia |
| 385 | Providing and laying cement concrete 1:5:10 (1 cement: 5 coarse sand: 10 graded stone aggregate 40 mm nominal size)alround CI HUBLESS includingbed concrete as per standard designNote: This work shall be done all-round PIPE AT ground floor\"s toilet. 100mm diameter |
| 386 | Providing, fixing and jointing in position UPVC (SWR) pipe Type-B for soil waste, rain water and ventor antisyphonage pipe of approved make including all fittings (plain or door) e.g. bends, junctions, cowls, offsets, access pieces jointingincluding fixing the pipe on the wall/ceiling with suitable clamps ,holder bat clamps andanchor fastener of approved design toSWR pipe embedded, cement concrete block 10x10x 10 cm of 1:2:4 ( 1 cement: 4 coarse sand:4 graded stone aggregate 20 mm nominal size), cutting holes in wall and floors, excavation, refilling and disposal of surplus earth where required and marked good complete etc. and as per direction of Engineer in Charge.40 mm dia |
| 387 | 50 mm dia |
| 388 | 110 mm dia |
| 389 | Providing and fixing UPVC(SWR) Type-B of size 110 mm x75x40 mmMulti Floor Trap along with 110 mm dia PVC pipe up to floor level andPVC grating of approvedmake with suitable jointing to ensure leak proof service as per instruction for laying & jointing recommended by the manufacturer and including cement concrete 1:2:4 under and around the multi floor trapwhere requiredup to floor level complete in all respects including cutting and making good the walls and floors etc. complete in all respect as per full satisfactionof theEngineer – in – Charge. With 63 mm i/d outlet.( 110 x 75 x 40) |
| 390 | Providing and fixing UPVC(SWR) Type-B of size 110 mm x 90 mmNahani Trap along with 110 mm dia PVC pipe up to floor level andPVC grating of approved make with suitable jointing to ensure leak proof service as per instruction for laying & jointing recommended by the manufacturer and including cement concrete 1:2:4 under and around the Nahanitrapwhere requiredup to floor level complete in all respects including cutting and making good the walls and floors etc. complete in all respect as per full satisfactionof theEngineer – in – Charge.With 90 mm i/d outlet. |
| 391 | Providing and fixing end cap (door piece) of uPVCfor cleaning.with 110 OD |
| 392 | Providing and fixing uPVC 110mm P Trap with minimum 50mm water seal with rubber seal on inlet to push fit hopper for indirect waste connections |
| 393 | Providing, fixing, testing and commissioning ofpipe inlet fittings fabricated withUpvcwith maximum 3 inlets 40, 50 & 75 mm OD size Upvc pipe, fixed to \"P\" traps includingDripseal/Pipe seal/solvent /rubber ring joint complete . |
| 394 | Providing and fixing in position 25 mm diameter mosquito proof coupling of approved municipal design. |
| 395 | Providing and fixing CPVC pipes having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipe with clamps at 1.00 mt spacing. this includes jionting of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of engineer in charge.Internal work -Exposed on Wall15 mm nominal outer dia pipes |
| 396 | 20 mm nominal outer dia pipes |
| 397 | 25 mm nominal outer dia pipes |
| 398 | 32 mm nominal outer dia pipes |
| 399 | 40 mm nominal outer dia pipes |
| 400 | 50 mm nominal outer dia pipes |
| 401 | Providing and fixing CPVC pipes having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipe with clamps at 1.00 mt spacing. this includes jionting of pipes and fittings with one step CPVC solvent cement and the cost of cutting chases and making good the wall same including testing of joints complete as per the direction of engineer incharge concealed work including cutting chases and making good the wall etc.15 mm nominal outer dia pipes |
| 402 | 20 mm nominal outer dia pipes |
| 403 | Providing and fixing G.I. pipes complete with GI fittings and clamps including cutting and making good the walls etc. (internal work)For roof level25 mm dia, nominal bore |
| 404 | 32 mm dia, nominal bore |
| 405 | 40 mm dia, nominal bore |
| 406 | 50 mm dia, nominal bore |
| 407 | 65 mm dia, nominal bore |
| 408 | Providing and fixing of gun metal gate valve with CI wheel of approved quality (screwed ends)25mm dia, nominal bore |
| 409 | 32 mm dia, nominal bore |
| 410 | 40 mm dia, nominal bore |
| 411 | 50 mm dia, nominal bore |
| 412 | Providing and fixing gun metal non- return valve of approved quality (PN 1.6)40 nominal bore |
| 413 | 50 nominal bore |
| 414 | 80 nominal bore |
| 415 | Providing and fixing brass stop cock of approved quality15mm nominal bore |
| 416 | 20mm nominal bore |
| 417 | Structual steel work welded in built up sections, trusses and framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steelprimer all complete. |
| 418 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 419 | BUTTERFLY VALVE (MANUAL) with C I body SS Disc, Nitrile Rubber Seal & O- Ring PN 16 pressure rating for chilled water/hot eater circulation as specified65 nominal bore |
| 420 | 80 nominal bore |
| 421 | Butterfly valve (manual) 100 NB |
| 422 | Supplying and fixing of following thickness duly laminated aluminum foil of mat finish closed cell Nitrile rubber (Class “O”) insulation on gyeser and solar water pipe suitable adhesive for Nitrile rubber. The joints shall be sealed with 50 mm wide and 3 mm thick self adhesive nitrile rubber tape insulation complete as per specifications and as required.19mm |
| 423 | Providing and fixing GI pipes medium class conferming to IS 1239 with GI fittings including cutting hole chase painted with primer, two coats of enamel paints etc80 mm dia, NB |
| 424 | GI pipes medium class, 100 mm NB |
| 425 | Providing and fixing brass ball valve with SS 304 Stem and ball, teflon seat complete (PN-40).15 mm dia nominal bore |
| 426 | 20 mm dia nominal bore |
| 427 | 25 mm dia nominal bore |
| 428 | Providing, fixing, testing and commissioning of motorised butterfly valve of following dia for filling of overhead water tank complete with high and low level control switches to control tanks. The level controllers shall be installed in iverhead tanks. The level switch will close the valve when water level is high in overhead tank and open the valve when overhead water tank level is low. The system should be complete in all respects with accessories 220 V AC / 2 V DC, IP67 electrical water level control unit, copper control wiring in whether proof casing etc.50 mm dia NB Float Valve |
| 429 | Solar Water HeatersSupply, erection, testing & commissioning of solar water heating system with following details :System temperature output : 60 degree C (during clear sunny days) System type : Thermo syphonSystem : Non PressurisedApplication : Bathing / Washing / CookingType of Solar Collectors : Copper tube Flat Plate Collectors as per BIS with following specifications -Size of Collector : 2080 x 1070 x 100 mmNumber of Collector : To suit system requirement. Absorber area : 2 sq MType : Cu - Cu Weight : 46 Kg (Dry)Absorber Coating : Selective - NALSUN Absorbivity : > 0.95Emissivity : < 0.2Frame Material : 16 SWG extruded Aluminium Glazing : Toughened GlassGlass beeding : EPDMFinish : Painted by approved shade Eelectrical element and control panel Hot water return pumpHardware : SS 304 Insulation : PUFCollector Stand : 35x35x3 mm MS angleHot Water Tank : Cylindrical - vertical / horizontal, Stainless steel 304 grade with 100 mm thick Rock Wool insulation including 22 SWG aluminium cladding.The entire system should be complete with internal piping in G.I. (class B) with 50mm rock wool insulation of density 48 kg/m3with 26 SWG Al claddingnecessary |
| 430 | INTERNAL ELECTRIFICATION |
| 431 | Wiring for light/fan/exhaust point with 1.5 sq.mm FRLS PVC cable in conduit (Group C). |
| 432 | Wiring for light/fan/exhaust/call bell point with 1.5 sqmm FRLS PVC Cu cable in conduit, modular switch, earthing etc. (Group A) |
| 433 | Wiring for light/fan/exhaust/call bell point with 1.5 sqmm FRLS Cu cable in PVC conduit with modular switch/plate & GI box incl. earthing |
| 434 | Group controlled (looped) point wiring with 1.5 sqmm FR Cu cable in steel conduit, modular accessories, earthing |
| 435 | Twin control light point wiring with 1.5 sqmm FRLS Cu cable in PVC conduit, 2-way modular switch, GI box, earthing |
| 436 | Wiring for light/power plug with 2×4 sqmm FRLS Cu + 1×4 sqmm earth in PVC conduit |
| 437 | Wiring for light/power plug with 4×4 sqmm FRLS Cu + 2×4 sqmm earth in PVC conduit |
| 438 | Circuit/submain: 2×1.5 sqmm + 1×1.5 sqmm earth |
| 439 | Circuit/submain: 2×2.5 sqmm + 1×2.5 sqmm earth |
| 440 | Circuit/submain: 2×4 sqmm + 1×4 sqmm earth |
| 441 | Circuit/submain: 2×6 sqmm + 1×6 sqmm earth |
| 442 | Circuit/submain: 4×10 sqmm + 2×6 sqmm earth |
| 443 | Circuit/submain: 4×16 sqmm + 2×6 sqmm earth |
| 444 | GI box with modular plate & 5/6A socket + 5/6A switch |
| 445 | GI box with modular plate & 6 pin 15/16A + 5/6A socket with shutter & 15/16A switch |
| 446 | Call bell/buzzer, 230 V |
| 447 | Steel conduit with accessories — 25 mm (surface/recess incl. painting or recessed cutting & making good) |
| 448 | Steel conduit with accessories — 32 mm |
| 449 | 20A, 240V SPN industrial socket with metal enclosed plug top & 20A ‘C’ curve SP MCB in sheet-steel enclosure |
| 450 | Medium class PVC conduit 25 mm with accessories (surface/recessed) |
| 451 | Medium class PVC conduit 32 mm with accessories |
| 452 | GI box with modular plate, 25A modular socket & 25A SP MCB “C” curve |
| 453 | 30A, 415V TPN industrial socket with 30A TP MCB in steel enclosure |
| 454 | 75×75×10 mm zinc-passivated box with RJ45 socket for data point |
| 455 | Drawing UTP 4-pair CAT6 LAN cable – 1 run |
| 456 | TP&N MCB DB 415V, 4 way (4+12), double door |
| 457 | TP&N MCB DB 6 way (4+18), double door |
| 458 | TP&N MCB DB 8 way (4+24), double door |
| 459 | SP&N MCB DB 8 way, double door |
| 460 | MCB “C” curve SP 5–32A |
| 461 | RCCB 63A, 4P, 30 mA |
| 462 | RCCB 40A, DP, 30 mA |
| 463 | Cubical LT switchboard (IP52) with 100A 4P MCCB, meters, lamps, bus bars; outgoing 63A 4P MCB-6 Nos & 40A DP MCB-2 Nos |
| 464 | 75×75 modular GI box with base & cover |
| 465 | 0.5 mm dia FR PVC copper telephone cable – 2 pair |
| 466 | Telephone socket outlet (modular) |
| 467 | TV outlet (modular) |
| 468 | Co-axial TV cable RG-6 – drawing in conduit |
| 469 | Telephone tag block – 20 pairs |
| 470 | GI earth plate 600×600×6 mm with enclosure, pipe, charcoal/salt etc. |
| 471 | 25×5 mm GI strip laid as strip electrode |
| 472 | 25×5 mm GI strip in 40 mm GI pipe from electrode |
| 473 | 25×5 mm GI strip on surface/in recess |
| 474 | 6 SWG GI wire on surface/in recess for loop earthing |
| 475 | 10W LED Downlighter (recessed/surface), Al die-cast, ≥90 lm/W, 5-yr warranty |
| 476 | 22W LED Tubelight |
| 477 | 18W LED Tubelight |
| 478 | 2′×2′ 34W LED Panel |
| 479 | 10W LED Bulkhead |
| 480 | 305 mm, 1400 RPM exhaust fan with louver & bird guard |
| 481 | Ceiling fan complete with blades/downrod etc. – 1200 mm sweep |
| 482 | Installation, testing & commissioning of fluorescent/compact fitting incl. connection |
| 483 | Installation, testing & commissioning of ceiling fan incl. wiring of downrod |
| 484 | Installation of exhaust fan up to 450 mm sweep incl. making opening, connection etc. |
| 485 | Extra for fixing louvers/shutters with frame for exhaust fan |
| 486 | Two-module stepped electronic fan regulator |
| 487 | Supply of Sereno high-efficiency LED luminaire (42 W, 2950 lm) Philips SP824 P LED 30S-5000 GR OA. |
| 488 | Providing and fixing lightning arrester rod with copper tape and GI pipe earth termination as per IS:2309 |
| 489 | EXTERNAL ELECTRIFICATION |
| 490 | Providing & fixing MV Danger Notice Plate (200×150 mm, 2 mm MS, vitreous enamel) |
| 491 | Providing & fixing HT Danger Notice Plate (250×200 mm, 2 mm MS, vitreous enamel) |
| 492 | 11 kV HT DP structure complete (RSJ poles, AB switch, HG fuses, LA, insulators, stays, foundations, painting, accessories & commissioning) |
| 493 | 11 kV HT metering panel (indoor) with trivector meter, CT/PT set, tested/approved by supply authority |
| 494 | 11 kV HT switchboard (single panel, VCB 630A with protections, CT/PT set, relays, power pack, joint box etc.) |
| 495 | 230V AC to 24V DC battery charger (SMPS) with 24V, 120Ah SMF batteries & DC DB (1×63A DP + 12×20/16A DP MCBs) |
| 496 | 250 kVA, 11/0.433 kV ONAN transformer with OLTC, AVS & RTCC, complete as specified |
| 497 | 3C×300 sq.mm, 11 kV (E) XLPE Al. armoured cable (supply) |
| 498 | Laying 11 kV power cable above 120 sq.mm up to 400 sq.mm direct in ground |
| 499 | Indoor 11 kV end termination (HS kit) for 3C Al. XLPE 300 sq.mm |
| 500 | Outdoor 11 kV end termination (HS kit) for 3C Al. XLPE 300 sq.mm |
| 501 | Providing/laying RCC NP2 Hume pipe 150 mm ID with collars, trenching & refilling |
| 502 | Providing/laying RCC NP2 Hume pipe 300 mm ID with collars, trenching & refilling |
| 503 | Fire bucket set (4 nos with stand), filled with sand, painted & complete |
| 504 | Approved Single Line Diagram framed (1000×800 mm) installed in MSR |
| 505 | First Aid box |
| 506 | Tool kit with one pair 11 kV rubber hand gloves |
| 507 | Shock-treatment charts (Eng & Hindi) framed and covered with glass |
| 508 | Safety mat, Class B, 1.2 m wide, 2.5 mm thick (12 kV withstand) |
| 509 | Safety mat, Class A, 1.2 m wide, 2.0 mm thick (1.1 kV withstand) |
| 510 | 62.5 kVA DG set with outdoor acoustic enclosure, controller, batteries/charger, base, AV pads, foundation & commissioning |
| 511 | Main LT Panel (415V, 3Ø4W, 55 kA, Form-3B, type tested) with incomer from 250 kVA Tx, metering/relays, 500A TPN Al busbar & listed outgoings |
| 512 | Incomer from 60 kVA DG – essential panel with 125A busbar & listed outgoings (4×63A FP MCCB + 40×40A DP MCB), metering/indication |
| 513 | Capacitor Panel 90 kVAr with APFC relay, 200A busbar & staged banks (25/10/5 kVAr) with contactors & protections |
| 514 | External Lighting Panel (OD, weatherproof) 63A FP MCCB incomer, metering, SPD, 100A busbar & outgoings |
| 515 | Feeder Pillar-1 (Type-3, Type-2, Type-5 & Guest House) 200A incomer, 250A busbar, outgoings 2×100A + 6×63A MCCB |
| 516 | Feeder Pillar-2 (Boys Dormitory, Type-4, Girls Dormitory, Kitchen & Dining) 200A incomer, 250A busbar, outgoings 6×63A MCCB |
| 517 | MDB Panel Type-2 (G+4) 100A incomer, 125A busbar, 14×40A FP MCB outgoings |
| 518 | MDB Panel Type-3 (G+2) 63A incomer, 100A busbar, 10×40A FP MCB outgoings |
| 519 | MDB Panel Type-3 (G+1) 63A incomer, 100A busbar, 7×40A FP MCB outgoings |
| 520 | MDB Panel Type-5 / Type-4 / Guest House (set of 3) 63A incomer, 100A busbar, 6×40A FP MCB outgoings |
| 521 | MDB Panel – School, Boys Dorm, Girls Dorm, Kitchen & Dining (set of 4) with mixed outgoings 4×63A + 4×40A FP MCB + 4×25A DP MCB |
| 522 | Laying 1.1 kV power cable up to 35 sq.mm direct in ground |
| 523 | Laying above 35 sq.mm & up to 95 sq.mm direct in ground |
| 524 | Laying above 95 sq.mm & up to 185 sq.mm direct in ground |
| 525 | Laying above 185 sq.mm & up to 400 sq.mm direct in ground |
| 526 | Supply 2×6 sq.mm Al. armoured cable (28 mm) |
| 527 | Supply 4×10 sq.mm Al. armoured cable (28 mm) |
| 528 | Supply 3½×35 sq.mm Al. armoured cable (32 mm) |
| 529 | Supply 3½×50 sq.mm Al. armoured cable (35 mm) |
| 530 | Supply 3½×70 sq.mm Al. armoured cable (38 mm) |
| 531 | Supply 3½×95 sq.mm Al. armoured cable (45 mm) |
| 532 | Supply 3½×120 sq.mm Al. armoured cable (45 mm) |
| 533 | Supply 3½×150 sq.mm Al. armoured cable (50 mm) |
| 534 | Supply 3½×185 sq.mm Al. armoured cable (57 mm) |
| 535 | Supply 3½×240 sq.mm Al. armoured cable (62 mm) |
| 536 | Supply 3½×300 sq.mm Al. armoured cable (70 mm) |
| 537 | End termination for 2×6 sq.mm (DSR-equiv) |
| 538 | End termination for 4×10 sq.mm |
| 539 | End termination for 3½×35 sq.mm |
| 540 | End termination for 3½×50 sq.mm |
| 541 | End termination for 3½×70 sq.mm |
| 542 | End termination for 3½×95 sq.mm |
| 543 | End termination for 3½×120 sq.mm |
| 544 | End termination for 3½×150 sq.mm |
| 545 | End termination for 3½×185 sq.mm |
| 546 | End termination for 3½×240 sq.mm |
| 547 | End termination for 3½×300 sq.mm |
| 548 | Earthing with 600×600×6 mm GI earth plate, enclosure, cover & watering pipe with charcoal/coke & salt |
| 549 | Earthing with 600×600×3 mm Cu earth plate, enclosure (CI cover), watering pipe with charcoal/coke & salt |
| 550 | 25×5 mm copper strip on surface/in recess for connections |
| 551 | 25×5 mm GI strip on surface/in recess for connections |
| 552 | Erection of metallic pole above 3 m & up to 6 m in CC 1:3:6 foundation |
| 553 | 100 W LED floodlight IP66 (≥10,000 lm), complete |
| 554 | 45 W LED post top light IP65 (≥4,500 lm), complete |
| 555 | 42 W LED gate light IP65 (≥4,200 lm), complete |
| 556 | 45 W LED street light IP66 (≥4,500 lm), complete |
| 557 | 45 W LED solar street light on 4 m GI octagonal pole (integrated), complete |
| 558 | 4.0 m GI octagonal pole with inbuilt JB & base plate (single/double arm) |
| 559 | 200×150×125 mm polycarbonate IP55 junction box with SP MCBs & TB |
| 560 | Cable through GI pipe to JB & 2×2.5 sq.mm Cu wiring from JB to fixture |
| 561 | FIRE FIGHTING |
| 562 | Supplying, installation, testing and commissioning of electric driven terrace pump (450 LPM at 35 m head) complete with motor, base plate, coupling, anti-vibration pad etc. |
| 563 | Control panel for terrace booster pump (MCCB 35A, bus bars, ammeter, voltmeter, DOL starter, OLR, phase preventor, ON/OFF push buttons, Auto/Manual selector) |
| 564 | Fire brigade connection (2-way, 100 mm dia MS pipe) |
| 565 | Pressure switch in MS pipeline including connection |
| 566 | Single-headed internal hydrant valve (SS Type-A IS 5290) with blank cap & chain |
| 567 | Short branch pipe (63 mm dia, SS Grade 304) with 20 mm nozzle |
| 568 | RRL hose pipe 63 mm dia × 15 m long with SS couplings |
| 569 | First-aid hose reel (MS), 40 m; hose, gunmetal valve & nozzle, drum, brackets, connections to riser |
| 570 | Angle iron (40×40×5 mm) door frame & 6 mm MS/glass shutter 2.1×0.9 m with fittings, locking & painting |
| 571 | Laying, testing & commissioning of C-class heavy-duty MS pipe 100 mm dia (IS 1239/3589) incl. fittings, welding, supports, coating |
| 572 | C-class MS pipe 100 mm dia (wall/ceiling with painting) |
| 573 | C-class MS pipe 80 mm dia (wall/ceiling with painting) |
| 574 | C-class MS pipe 25 mm dia (wall/ceiling with painting) |
| 575 | Butterfly valve PN 1.6, 100 mm dia, ISI marked (bronze/gunmetal seat) |
| 576 | Non-return valve 100 mm dia IS 5312 with gasket, bolts & washers |
| 577 | Gunmetal gate valve 25 mm nominal bore with CI wheel (screwed end) |
| 578 | SS Y-strainer 100 mm dia, Grade 304 |
| 579 | Pressure gauge (0–15 kg/cm²) with shut-off valve |
| 580 | Air vessel 250 mm dia, 8 mm MS, 1200 mm height with air-release valve, gauge, painting & fittings |
| 581 | Fire extinguisher — CO₂ type, 4.5 kg, ISI marked, with hose & wall bracket |
| 582 | Fire extinguisher — ABC powder type, 6 kg, ISI marked, with gauge, valve & wall bracket |
| 583 | ROOFTOP SOLAR SYSTEM |
| 584 | Supply, Installation testing and commissioning of grid intarective roof top solar photo valtaic power generation system including space frame complete. |
| 585 | FURNITURE |
| 586 | Supply & installation Big Desk (for two persons)-The overall dimensions of desk will be 1066mm * 930mm * Height 760mm, complete as perSpecifications enclosed and direction of Engineer-in- charge having the Table top shall be made up of 18.0 mm thick plywood IS 303 of MR Grade OSL (one side shall be laminated, and other side shall have balancer finish). Table top dimensions shall be W 850 mm x D 380 mm. Edge towards bench shall be post formed with round edge. The remaining three edges must be sealed with 2mmthick PVC edge banding tape. Edge band must be trimmed on edges and corners. The desk shall be Greenguard certified for low chemical emission of VOCs (Voltage Organic Compounds) and carcinogens, contributing to a healthier room environment. Valid certificate to be submitted along with the bid. Make of Plywood : Merino / Greenply / Century / Kitply. Make of Laminate & balancer : Marino / Greenlam / ASIS / Century following specifications. Seat and back rest shall be made of 18mm thick plywood of MR Grade OSL (one side shall be laminated, and other side shall have balancer finish) except back rest. Back rest shall be have both sides colour lamination.Technical details of seat and back rest are mentioned below:Seating bench dimensions shall L 900 mm x W 300 mm. Front side shall be rounded with post forming. Remaining three edges shall sealed with 2mm thick PVC edge banding tape.Back rest dimensions shall L 900 x H 200 mm Upper side shall be rounded with post forming Remaining three edges shall be sealed with 2mm thick PVC edge banding tape. Desk Shelve shall be made of prime quality 0.8mm thick CRCA sheet of H150mmxD300mm and side stiffeners of MS CRCA tube size 19mmx19mmx1mmthick. One vertical support (partition) of square tube size 25mm square x1.2mm thick must be provided at centre of tray . Upper moedsty made of prime quality 0.8mm thick CRCA Sheet Powder Coated should be embossed with dimples in round shape, height will be 150mm, there should be Perforated lower modesty Made of prime quality 0.8 mm thick CRCA sheet of size H150mmXD21mm with square perforation, CRCAT ube of size 19x19x1mm thick to be inserted for full length at bottom of Jali . Bag hook should be provide on both side of piller made of minimum 4mm dia rod Side frame structure:- Made of prime quality CRCA pressed form section 165mmx25mmx1mm thick welded to 25mmx50mmx1.2mm thick CRCA tube , Seat and back side frame structure made of prime quality CRCA pressed form section 165mmx25mmx1mm thick welded to 25.4mm diameter x 1.6mm thick ERW-1pipe , there will be 8no. horizontal supports are 25mmx25mmx1.2mm thick CRCA pipes. . Bottom Rectangular tube 50x25x 1.2mm thick should be closed with PPCP cap bothside sand pipe dia. 25.4x1.6mm thick should be closed with metal (Backside) and other side (Undertheseat) PPCP cap, complete as per engineer incharge Desk should be in semi knock down form with the help 16 connecting pipes ; 8 pipes on each side : connecting pipe size will be 20x20x1.2mm .All Metal Pieces Shall Be Welded Properly Strongly and conformity with regulations with CO2 Welding Shall Be Used , CRCA Metal Shall Be Coated After Being Treated With At Least Three Stages And Cleaned From Oil , Grease , Dust And Other Dirt Using Special Thermal Control Coating For Metal Furniture To Form a Layer Of Base Coating Of (iron phosphating) (0.4 – 0.8) gm/m² , Automatic Spray Coating Shall Be Applied To Be Followed By a Drying Process In a Thermal Furnace With Suitable Temperature And Time For The Process , Metal Pipe & 7 tank treatment with minimum 45-50 micron powder coating . Company being an OEM and have ISO 9001,ISO 45001,ISO14001, ISO50001 (NABCB Accredited),AIOTA, GREENCO,GREENPRO,IGBC,GRIHA |
| 587 | Supply & installation Medium Desk (for two persons)-The overall dimensions of desk will be 900mm W± 5 X 890mm D± 5 X 688/420mm H± 5 , complete as per Specifications enclosed and direction of Engineer-in- charge having the Table top shall be made up of 18.0 mm thick plywood IS 303 of MR Grade OSL (one side shall be laminated, and other side shall have balancer finish). Table top dimensions shall be W 850 mm x D 380 mm. Edge towards bench shall be post formed with round edge. The remaining three edges must be sealed with 2mmthick PVC edge banding tape. Edge band must be trimmed on edges and corners. The desk shall be Greenguard certified for low chemical emission of VOCs (Voltage Organic Compounds) and carcinogens, contributing to a healthier room environment. Valid certificate to be submitted along with the bid. Make of Plywood : Merino / Greenply / Century / Kitply. Make of Laminate & balancer : Marino / Greenlam / ASIS / Century following specifications. Seat and back rest shall be made of 18mm thick plywood of MR Grade OSL (one side shall be laminated, and other side shall have balancer finish) except back rest. Back rest shall be have both sides colour lamination.Technical details of seat and back rest are mentioned below:Seating bench dimensions shall L 900 mm x W 300 mm. Front side shall be rounded with post forming. Remaining three edges shall sealed with 2mm thick PVC edge banding tape. Back rest dimensions shall L 900 x H 200 mm Upper side shall be rounded with post forming Remaining three edges shall be sealed with 2mm thick PVC edge banding tape. Desk Shelve shall be made of prime quality 0.8mm thick CRCA sheet of H150mmxD300mm and side stiffeners of MS CRCA tube size 19mmx19mmx1mmthick. One vertical support (partition) of square tube size 25mm square x1.2mm thick must be provided at centre of tray . Upper moedsty made of prime quality 0.8mm thick CRCA Sheet Powder Coated should be embossed with dimples in round shape, height will be 150mm, there should be Perforated lower modesty Made of prime quality 0.8 mm thick CRCA sheet of size H150mmXD21mm with square perforation, CRCAT ube of size 19x19x1mm thick to be inserted for full length at bottom of Jali . Bag hook should be provide on both side of piller made of minimum 4mm dia rod Side frame structure:- Made of prime quality CRCA pressed form section 165mmx25mmx1mm thick welded to 25mmx50mmx1.2mm thick CRCA tube , Seat and back side frame structure made of prime quality CRCA pressed form section 165mmx25mmx1mm thick welded to 25.4mm diameter x 1.6mm thick ERW-1pipe , there will be 8no. horizontal supports are 25mmx25mmx1.2mm thick CRCA pipes. . Bottom Rectangular tube 50x25x 1.2mm thick should be closed with PPCP cap bothside sand pipe dia. 25.4x1.6mm thick should be closed with metal (Backside) and other side (Undertheseat) PPCP cap, complete as per engineer incharge Desk should be in semi knock down form with the help 16 connecting pipes ; 8 pipes on each side : connecting pipe size will be 20x20x1.2mm .All Metal Pieces Shall Be Welded Properly Strongly and conformity with regulations with CO2 Welding Shall Be Used , CRCA Metal Shall Be Coated After Being Treated With At Least Three Stages And Cleaned From Oil , Grease , Dust And Other Dirt Using Special Thermal Control Coating For Metal Furniture To Form a Layer Of Base Coating Of (iron phosphating) (0.4 – 0.8) gm/m² , Automatic Spray Coating Shall Be Applied To Be Followed By a Drying Process In a Thermal Furnace With Suitable Temperature And Time For The Process , Metal Pipe & 7 tank treatment with minimum 45-50 micron powder coating . Company being an OEM and have ISO 9001,ISO 45001,ISO14001, ISO50001 (NABCB Accredited),AIOTA, GREENCO,GREENPRO,IGBC,GRIHA |
| 588 | Supplying and installation of site knock down type Office Table as per approved design and directrion of Engineer-in-charge.Work Top - Work top shall be made 25mm thick Pre-laminated MDF board with decorative lamination on one side and balancing lamination on other side confirming to IS 12406:2003 with post forming on front, back and machine pressed PVC egde banding 2mm thick glued with industrial adhesive and diffused with board monolithically on other two sides. Table top shall have 75mm overhung on front and 25mm overhung on sides. Understructure- C-type leg shall be made of tubular section of 50mm x 50mm x 1.6mm (wall thickness) thick vertical member and40mm x40mm x1.6mm (wall thickness) Horizontal M.S. pipe confirming IS-Grade 4932 shall be finished with epoxy polyster powder coated DFT 50-60 Micron. The legs shall be fitted to the ground with M8 screw leveler with the height adjustment up to 15mm. The cross members shall be mounted by end brackets made of 3mm thick CRCA steel sheet confirming IS 513: 2008and finished with epoxy polyster powder coated DFT 50-60 Micron confirming IS 13871:1993.Wire management - Electrical wires shall be carried from horizintal/ vertical duct made of 0.7mm CRCA steel sheet confirming to IS 513:2008. The switch plate or grommet depending upon requirement shall also be provided for electrical/LAN connection on table top.Modesty Panel -Modesty Panel of height 450mm shall be made of 1.5mm thick CRCA sheet sheet confirming to IS 513: 2008and shall be finised with epoxy polyster powder coated DFT 50-60micron.Storage body- Storage top shall also be made of 25mm thick Pre-lam MDF board confirming to IS 12406:2003 with post forming on two sides and machine pressed PVC egde banding 2 mm thick glued with industrial adhesive and diffused with board monolithically on other two sides. The body of storage unitsshall be made of 0.8mm thick CRCA steel Sheet and skirting shall be of 1.2mm thick CRCA steel sheet confirming to IS 513: 2008 finished with epoxy powder coated of DFT 50-60 Micron confirming IS 13871:1993. Internal Shelves shall be also made up of 0.8mm CRCA steel sheet confirming to IS 513: 2008 and shall be mounted with the Metal shelf support pin made of 2mm thick CRCA Steel sheet with Nickel or Chrome plating.M10 screw leveler is given with height adjustment up to 12mm to 15mm.Table of Size 1800mm (W) x 750mm (D) x 750mm (H) with Side Storage of Size 900mm (W) x 450mm (W) X 750mm (H) and Back Storage 1800mm (W) x 450mm (D) x 750mm (H) |
| 589 | Table of Size 1650mm (W) x 750mm (D) x 750mm (H) with Side Storage of Size 900mm (W) x 450mm (W) X 750mm (H) and Back Storage1650 mm (W) x 450mm (D) x 750mm (H) |
| 590 | Office table with overall Size of desk 1350mm (L) x 750mm (W) x 750mm (H)& Side Storage Unit of size 900mm (L) x 450mm (W) x 750mm (H) |
| 591 | Supplying and installation of knock down type Office Table made of Pre-laminated MDF board with decorative lamination on one side and balancing lamination on other side top of size 1199 X 590 X 735 mm. Worktop shall be rounded in all four corners and should have an overhung of 50mm alongwith one drawer unit made of 0.5mm thick CRCA Steel sheet. The table top shall be supported over legs consists of MS ERW round tube of 25mm dia x 1.2mm (wall thickness) and Cross Horizontal Members including Leg rest of 25mm dia x 1.2mm (wall thickness) M.S. ERW tube. All steel components be shall be finised with epoxy polyster powder coated DFT 50-60micron. |
| 592 | Supplying and installation of knock down type 12 Seater Meeting Table of of overall size 3600 x 1350 (maximum) x 750 mm (Knock down type). Table Top shall be made of 25mm thick Pre-laminated Partical Board with decorative lamination on one side and balancing lamination on other side whereas the Gable Ends shall be of 25mm thick Pre-laminated Partical Board with decorative lamination on bothside alongwith 2mm thick machine pressed PVC edge banding glued with industrial adhesive and monolithically diffused. Supporting Understructure consists of2 Metal C Legs on either ends of table support frame made of 50mm x 50mm x 1.6 mm (wall thickness) MS ERW tube and One number Wire Carrier leg at middle of 50mm x 50mm x1.6mm (wall thickness), 4 numbers Horizontal connector of 40mm X 40mm X 1.6mm thick MS Pipe between supportingvertical legs.All The MS Pipes and Sheetshall be finished with epoxy powdercoated of DFT 50-60micron. The \"C\" typed metal legs shall be kept 150mm inside from outer edge of table top.WIRE MANAGEMENT -The Vertical (stake) & Horizontal (cable tray) wire carriers are placed below worktop, made up of CRCA steel sheet with epoxy powder Coating & Fixed to the understructure with specially designedbrackets, includingprovision of placing switch plates/grommet in the cable tray . |
| 593 | Supplyand installation of Library Table in sizes of 2400mm (L)x 900mm (W) x 750mm (H) consisting of follwing specification:-Work Top - Work top shall be made of 25mm thick Pre-laminated Partical Board with decorative lamination on one side and balancing lamination on other side confirming to IS 12823: 1990, alongwith 2 mm thick Machine pressed PVC edge banding glued with industrial adhesive and monolithically diffused with board on exposed edges.Understructure Supporting frame shall consists ofThree Metal C-Legs (two at either ends and one in middle of table) and joined by two numbers Horizontal connector made of tubular section 40mm x 40mm x 1.6mm (wall thickness) confirming to IS 4923:1997.The entire metalframe shall be finised with epoxy polyster powder coated DFT 50-60 Micron. C-typed metal legs shall be kept 150 mm inside from from end of table. Legs shall be fitted to the ground with M8 screw leveler with the height adjustment up to 12mm to 15mm. |
| 594 | Supplying and installation of knock down type Dual Computer Work Station of unit Size 1500mm (L) x 600m (W) x 750mm (H) for two students Work Top- Work top shall be made 25mm thick Prelam particle board with decorative lamination on one side and balancing lamination on other side confirming to IS 12823: 1990 with 2mm thick Machine pressed PVC edge banding glued with industrial adhesive and monolithically diffused with board on all sides. Understructure supporting frame consist of 2 Metal C Legs on either ends of table support frame made of 50mm x 50mm x 1.6 mm (wall thickness) MS ERW tube and One number Wire Carrier leg at middle of 50mm x 50mm x1.6mm (wall thickness), 4 numbers Horizontal connector of 40mm X 40mm X 1.6mm thick MS Pipe between supportingvertical legs. The MS Pipes shall be finished with epoxy powdercoated with DFT of 50-60 Micron confirming to IS 13871:1993. The legs shall be fitted to the ground with M8 screw leveler with the height adjustment up to 15mm. Wire management-The Vertical /Electrical duct & Horizontal Cabletray ( wire carriers) aremadeof CRCA steel sheet & fixed to the understructure below worktop with specially designedbrackets. Provision for fixing Switch platesare prividedin the cable tray for easy access through wire mangaer or PVC grommet. Screens / privacy panel: - Screen height will be 300mm above work-top made of prelam particle board/White Board alternatively as approved by Engineer-in-Charge. In addition privacy panel of 300 mm height, on work top, shall be provided between two workstation. |
| 595 | Supply and installation of Glass-door Storage of Size 916 mm (W) x 486mm (D) x 1980mm (H). It should have shelf thickness of 0.7mm, Back thickness of 0.8mm, Door thickness of 0.8mm (high yield strength) with clear glass of 3.0mm thick and all other components shall have a thickness of 0.9mm. These components shall be made of CRCA steel sheet ‘D’ grade high yield strength as per IS 513:2008 The glass door storwel shall have a SS handle and a Two-way locking mechanism with shooting bolt. It should have a height-wise adjustable shelf mounting which shall have a Uniformly Distributed Load Capacity of max 40 Kg. It should also have a M10 Screw type Leveller with Hex plastic base.All metal components would be epoxy polyster powder coated DFT 50-60 Micron confirimg to IS 13871:1993 |
| 596 | Overall Size 900WX300DX2100Hmm,Top made up of 18mm thick Postlam plywood with PVC edge banding ,Side panel made up of 18mm thick Postlam plywood with PVC edge bending , Skirting made up of 18mm thick Postlam plywood with PVC edge bending ,back panel made up of 18mm thick Postlam plywood , One number of drawer as per ref.image ,shelf made up of 18mm thick Postlam plywood with PVC edge bending, all Wooden Panels Fix Joints With Minifix Dowels & other Fitting Equipment , All Wooden Panels Prime Quality Board With ISI Marked. Complete structure design should be as per reference image only. |
| 597 | Supply adn installation of Lab Stool Seat Revolving Stool with Backrest Overall Dimension: 410W ±10 x 410D ±10 x 820H ±10 mm,Seat of chair is made of 12mm thick hot pressed Plywood pasted with High DensityPU foam & Leatherette upholstery, Back is made of 12mm thick hot pressed Plywood pasted with PU foam D -40 kg/m3 , H-20 Seat and back fixed through metal powder coated Spine covered with plastic cover, Seat Size: 400W ±10x 400D ±10 x 75Thick. ±5 mm, Back Size: 450W ±10 x 240H ±10 x 50Thick. ±5mm ,Ground to seat height-440-560mm,Mechanism:- Machanism Design With Features Of Revolving At 360 Degree .Machanism Provided Upright Position Locking,Seating Height Can Be Adjusted With a Pneumatic Gas Lift,Gaslift: Lift -Used gaslift of 90 mm size of Class-IV grade with plastic bellow cover,Chair Base & Wheels: Metal chrome plated Chair BaseMade of 2.5mm thick Metal chrome plated steel frame, base consists of 5 prongs with 560±5 mm pitch circle diameter, 50mm Dia. Black Nylon - Twin Wheel Pin castor . |
| 598 | High Back Revolving Chair, Overall Dimension:- 700W ±10 x 700D ±10 x 1210H ±10 mm,Seat of Medium back chair is made of 12mm thick hot pressed plywood pasted with PU Moulded foam with Fabric upholstery on Seat,Used PU Moulded foam on Seat of D-45 kg/m3 , Back ofchair is made of Injection moulded PP material structure upholstered with Mesh fabric , Adjustable Lumber support upholstered with fabric , Adjustable Headrest on back Upholstered with Mesh Fabric ,Seat Size:- 470W ±10 x 460D ±10 x 70Thick. ±5 mm , Back Size: 500W ±10 x 780H ±10,Mechanism:- The Synchro tilt Mechanism ,Used gaslift of 90 mm size of Class-IV grade,Armrest:- PU padded adjustable armrestfixed with Seat ,Chair Base & Wheels: MS Chrome Plated base consists of 5 prongs with 640±5 mm pitch circle diameter, 50mm Dia. Black Nylon - Twin Wheel Pin castor . |
| 599 | Medium Back Revolving Chair, Overall Dimension:- 720W ±10 x 720D ±10 x 1070H ±10 mm,Seat of Medium back chair is made of 12mm thick hot pressed plywood pasted with PU Moulded foam with Fabric upholstery on Seat , Used PU Moulded foam on Seat ofD-45 kg/m3 , Back of High back chair is made of Injection moulded PP material structure ,combination of upholstered with Mesh fabric , Seat and back connected through metal powder coated plate, Adjustable Lumber support upholstered with fabric , Seat Size:- 470W ±10 x 470D ±10 x 70Thick. ±5 mm , Back Size: 525W ±10 x605H ±10,Mechanism:- The Synchro tilt Mechanism ,Used gaslift of 90 mm size of Class-IV grade,Armrest: PU Padded Adjustable armrest fixed on frame,Chair Base & Wheels: Metal chrome plated Chair Base consists of 5 prongs with 650±5 mm pitch circle diameter, 50mm Dia. Black Nylon - Twin Wheel Pin castor. |
| 600 | Fixed Visitor Chair, Overall Dimension:- W600±10 x 600D ±10 x 890H ±10 mm,Seat of Medium back Visitor chair is made of 12mm thick hot pressed plywood pasted with PU Moulded foam with Fabric upholstery on Seat , Used PU Moulded foam on Seat of D-45 kg/m3, Back of Medium back chair is made of Injection moulded PP material structure with Mesh fabric, Seat Size:- 460W ±10x 470D ±10 x 60Thick. ±5 mm , Back Size:- 440W ±10 x 470H ±10,Armrest:- Fixed PP armrest ,Understructure:- Cantilever frame made powder coating ofround pipe 14 gauge thickneess with Plastic bushes . |
| 601 | Medium Back Revolving Chair, Overall Dimension:- 700W ±10 x 700D ±10 x 1010H ±10 mm,Seat of Medium back chair is made of 12mm thick hot pressed plywood pasted with PU Moulded foam with Fabric upholstery on Seat ,Used PU Moulded foam on Seat ofD-45 kg/m3 , Back of chair is made of Injection moulded PP material structure combination of upholstered with Mesh fabric , Seat and back connected through metal powder coated plate having Adjustable Lumber support upholstered with fabric , Seat Size:- 490W ±10 x 450D ±10 x 70Thick. ±5 mm , Back Size: 525W ±10 x640H ±10,Mechanism:- The Synchro tilt Mechanism ,Used gaslift of 90 mm size of Class-3 grade,Armrest: PU Padded Adjustable armrest,Chair Base & Wheels: Revolving Pedestal Nylon base consists of 5 prongs with 640±5 mm pitch circle diameter, 50mm Dia. Black Nylon - Twin Wheel Pin castor . |
| 602 | Supplying and installation of Metal Lockers with Cam Lock one unit consiting of 381mm (W) x 381mm (D) x 1831mm (H) with 4 Lockers. Body-LH and RH Side and back panel is made up of 0.8mm thick CRCA steel sheet confirming to IS 513:2008 which is having standard dimension 1831 x380mm. Shelf hanging bracket is welded on both the side panel by spot welding. Shelf hanging bracket is made up of 0.8mm thick CRCA steel sheet confirming to IS 513:2008. front frame, top and bottom part made up 0.8mm thick CRCA steel sheet confirming to IS 513:2008 and horizontal part is made up 1mm thick CRCA Steel sheet confirming to IS 513:2008. On a front frame horizontally provision is given at a common distance to hold shutter bracket. Locker’s top is made up of 0.8mm thick CRCA Steel sheet confirming IS 513:2008 which is having standard dimension 375 x378mm. Shelf is also made up of 0.8 mm CRCA Steel sheet confirming to IS 513:2008.Shutter- Is made up on 0.7mm thick CRCA Steel sheet confirming to IS 513:2008. All the shutter are hung on shutter pin and shutter bracket, louvers are given in shutter for air flow. PVC flush handle and name plate is used for handling and for name plate tagging. Standard locking arrangment is used for locking each shutter.The bodies including shelves are given anti-rust surface treatment & are powder coated with epoxy polyester powder coating of DFT 50-60 Micron confirimg to IS 13871:1993. |
| 603 | 1.Dimensions and ConfigurationTotal Width of the Setup: Minimum 12 feet. Height: Approximately 4 to 4.5 feet from the board surface.2.Sliding Boards:Quantity: 2 (Left and Right). Size (Each Board): 6 feet (W) × 4 feet (H)3.Material:Left: Green chalkboard (matte surface, suitable for chalk)Right: Whiteboard (glossy surface, suitable for dry-erase markers)4.Function: Boards shall slide horizontally on a top and bottom aluminum/steel channel track to fully cover or reveal the IFP as needed.5. Interactive Flat Panel (IFP)Position: Centered within the frame and between the two sliding boards.Mounting: Wall-mounted securely inside the board structure, with space allowance for ventilation and service access.IFP Opening Size: Sized appropriately to the IFP being installed (contractor to confirm model and dimensions).6.Frame Material: Laminated plywood or MDF with a natural wood finish or laminated color finish (as per architect/owner approval).7. Frame and Track SystemMaterial: Aluminum or powder-coated steel tracks with smooth sliding mechanism.Top & Bottom Rails: Tracks shall be aligned and reinforced to ensure boards move easily and without wobble.Finish: Durable, corrosion-resistant coating suitable for indoor use.8.. Additional RequirementsAll boards and the structure must be securely fixed to the wall with appropriate fasteners.Provision for cable management must be included for the IFP (i.e., concealed conduit/path for power and data cables).The unit must be free from sharp edges, splinters, or any protruding parts that could cause injury.Installation height should ensure comfortable writing access for average adult and student height (typically bottom edge ~2.5 to 3 feet from the floor). |
| 604 | Supply and installation of Physics Along the wall Lab Table of size1800(L) x 750(W) x 860(H)(9 no)with specification as under: Overall Size 1800W x 750D x 850H.Storage Box Size 1800W x 750D x 850 . Physics Island Lab Table of size1800(L) x 1500(W) x 860(H)(2 no)with specification as under:Overall Size 1800W x 1500D x 850H.Storage Box Size 1800W x 1500D x 850.Box Of Storage( 1D + 2S ).Storage Per Box Size Without Granite600W x 570D x 713H Using 100mm PVC Leg Supported .Storage Upper Top 19mm Thick Granite Top All Joints Will Be Filled With Silicon Sealent. Storage Upper Top Fixed Metal Cable Tray With Switch & Sockets.Made Of 0.8mm Thick CRCA Prime Quality MS Sheet With Approved Powder Coated Shade. Modesty Panel Are CRCA 0.8mm Thick Metal SheetWelded With Storage .Under Table Top Supported Beam CRCA 40x20mm 1.2mm ThickRectangular Metal Pipe Duly Powder Coated.All cabinets Bodies Shall Be Of Over Closing Design Components Parts Cut & Shaped Entirely On CNC Fabricating Machines With Contruction.Metal Storage Bodies Shall be Neatly Jointed Together With Accurrately Matching Sides Avoiding Any Gaps.Shutter Made Of 0.8mm Thick Powder CoatedMs Sheet Providing With Handles . Drawer Move On Sliding Teleslescopic Channel. AllMetallic PanelsScrew With NutBolt & Riviting . All Metal Pieces Shall Be WeldedProperly Strongly andconformity with regulations.CO2 Welding Shall Be Used.All Metal Shall Be Coated After Being Treated With At Least Three Stages And Cleaned From Oil,Grease, DustAnd Other Dirt Using Special Thermal Control Coating For Metal Furniture To Form a Layer Of Base Coating Of (iron phosphating) (0.4 – 0.8) gm/m² .Automatic Spray Coating Shall Be Applied To Be Followed By a Drying Process In a Thermal Furnace With Suitable Temperature And Time For The Process .Thickness Of Coating (40 – 50) Micron. The product should bear IGBC Green Pro certificate for product category.And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for LAB FURNITURE range for ergonomic design. |
| 605 | Supply and installation of Chemistry Along the wall Lab Table of size1800(L) x 750(W) x 860(H)(9 no)with specification as under: Overall Size 1800W x 750D x 850H.Storage Box Size 1800W x 750D x 850H1 x 1550H2 . 1 Nos. Reagent RackSize 1300W x 300D x 700H. Chemistry Island Lab Table of size1800(L) x 1500(W) x 860(H)(2 no)with specification as under:Overall Size 1800W x 1500D x 850H.Storage Box Size 1800W x 1500D x 850H1 x 1550H2 . 1 Nos. Reagent RackSize 1300W x 300D x 700H. Box Of Storage( 1D + 2S ) 0.8mm MS Sheet Powder Coated.Storage Per Box Size Without Granite600W x 570D x 713H Using 100mm PVC Leg Supported .Storage Upper Top 19mm Thick Granite Top All Joints Will Be Filled With Silicon Sealent.Innovate 02 Made Of 0.8mm Thick CRCA Prime Quality MS Sheet With Approved Powder Coated Shade. All cabinets Bodies Shall Be Of Over Closing Design Components Parts Cut & Shaped Entirely On CNC Fabricating Machines With Contruction.Metal Storage Bodies Shall be Neatly Jointed Together With Accurrately Matching Sides Avoiding Any Gaps.Shutter Made Of 0.8mm Thick Powder CoatedMs Sheet Providing With Handles.Drawer Move On Sliding Teleslescopic Channel. Reagent RackStructure Side PanelMade OfCRCA 1.2mm25x25 Square Metal Pipe Welded With 0.8mm Thick Metal Sheet & Shelve Are Made By Wooden & Metal Sheet With Added Switch & Socket .Innovate Granite Top Flushed With Sink-Unit & Tap .Installation Of All Utility Service OutletsAccessory Fittings, Plumbing , Electrical Switches & Fittings Identified On Drawings As Mounted On The Laboratory Furniture . AllMetallic PanelsScrew With NutBolt & Riviting .All Metal Pieces Shall Be WeldedProperly Strongly andconformity with regulations . CO2 Welding Shall Be Used . All Metal Shall Be Coated After Being Treated With At Least Three Stages And Cleaned From Oil,Grease, DustAnd Other Dirt Using Special Thermal Control Coating For Metal Furniture To Form a Layer Of Base Coating Of (iron phosphating) (0.4 – 0.8) gm/m² .Automatic Spray Coating Shall Be Applied To Be Followed By a Drying Process In a Thermal Furnace With Suitable Temperature And Time For The Process. Thickness Of Coating (40 – 50) Micron. |
| 606 | Supply and installation of Biology Along the wall Lab Table of size1800(L) x 750(W) x 860(H)(9 no)with specification as under: Overall Size 1800W x 750D x 850H.Storage Box Size 1800W x 750D x 850H1 x 1550H2 . 1 Nos. Reagent RackSize 1300W x 300D x 700H. Biology Island Lab Table of size1800(L) x 1500(W) x 860(H)(2 no)with specification as under:Overall Size 1800W x 1500D x 850H.Storage Box Size 1800W x 1500D x 850H1 x 1550H2 . 1 Nos. Reagent RackSize 1300W x 300D x 700H. Box Of Storage( 1D + 2S ) 0.8mm MS Sheet Powder Coated.Storage Per Box Size Without Granite600W x 570D x 713H Using 100mm PVC Leg Supported .Storage Upper Top 19mm Thick Granite Top All Joints Will Be Filled With Silicon Sealent.Innovate 02 Made Of 0.8mm Thick CRCA Prime Quality MS Sheet With Approved Powder Coated Shade. All cabinets Bodies Shall Be Of Over Closing Design Components Parts Cut & Shaped Entirely On CNC Fabricating Machines With Contruction.Metal Storage Bodies Shall be Neatly Jointed Together With Accurrately Matching Sides Avoiding Any Gaps.Shutter Made Of 0.8mm Thick Powder CoatedMs Sheet Providing With Handles.Drawer Move On Sliding Teleslescopic Channel. Reagent RackStructure Side PanelMade OfCRCA 1.2mm25x25 Square Metal Pipe Welded With 0.8mm Thick Metal Sheet & Shelve Are Made By Wooden & Metal Sheet With Added Switch & Socket .Innovate Granite Top Flushed With Sink-Unit & Tap .Installation Of All Utility Service OutletsAccessory Fittings, Plumbing , Electrical Switches & Fittings Identified On Drawings As Mounted On The Laboratory Furniture . AllMetallic PanelsScrew With NutBolt & Riviting .All Metal Pieces Shall Be WeldedProperly Strongly andconformity with regulations . CO2 Welding Shall Be Used . All Metal Shall Be Coated After Being Treated With At Least Three Stages And Cleaned From Oil,Grease, DustAnd Other Dirt Using Special Thermal Control Coating For Metal Furniture To Form a Layer Of Base Coating Of (iron phosphating) (0.4 – 0.8) gm/m² .Automatic Spray Coating Shall Be Applied To Be Followed By a Drying Process In a Thermal Furnace With Suitable Temperature And Time For The Process. Thickness Of Coating (40 – 50) Micron. |
| 607 | Dining Table: SS Dinning Table consists of Dinning Top is made up of 1 mm thickness Stainless steel sheet of SS 304 Grade with overall dimension of 1800(L) X 700(D) X 750(H). The table top is reinforced with a 18 mm ply Board on Stainless steel frame of square section 40mmx40mmx1.6mm. Dinning top of stainless steel sheet shall be extended to the sides and a depth upto 40 mm under the table top in all directions includingedge rounding, grinding and finishing etc. all complete. The Table top shall finish in such a manner to avoid any sharp edges. The table will be supported by four hollow legs made from SS 304 grade stainless steel. The hollow legs shall be of square type of size 50mmx50mmx1.6mm. These legs shall be securely welded or mechanically fastened to the underside of the tabletop frame. For additional structural stability, stainless steel cross supports shall be provided between the legs as shown in figure with 40mmx40mmx1.6mmSS square section. The table shall include rubber shoes at the bottom of each leg to prevent floor damage and ensure stability. The design shall prioritize user safety with no sharp corners or edges. The table must be structurally sound and capable of supporting a uniformly distributed load of at least 250 kg. All materials used must conform to relevant IS standards, and the finished product should be free from burrs, dents, or deformities |
| 608 | Dining Bench: The Bench shall be of size 1800 mm in length, 300 mm in depth, and 450 mm in height, suitable for use in residential schools. The bench top shall be made of 18 mm thick plywood + Laminated , finished with a 0.8 mm thick decorative laminate on the top surface, and a balancing laminatebacking on the underside to ensure dimensional stability. All exposed edges shall be sealed with PVC edge banding or machine-finished to prevent splinters and enhance durability. The plywood shall be scratch-resistant, water-resistant, and easy to clean, with a light woodgrain or equivalent finish as approved. The supporting frame shall be fabricated frame of square section 40mmx40mmx1.6mm MS Pipe in Powder Coated. These legs shall be securely welded or mechanically fastened to the underside of the benchtop frame. The bench shall include rubber shoes at the bottom of each leg to prevent floor damage and ensure stability. The design shall prioritize user safety with no sharp corners or edges. The bench must be structurally sound and capable of supporting a uniformly distributed load of at least 250 kg. All materials used must conform to relevant IS standards, and the finished product should be free from burrs, dents, or deformities |
| 609 | Providing and Placing in position Double Bed MS-STYLON-02Overall size of the bed shall be 2100 L mm x 1800 W mm x 900 H mm. Bed Made up of engineering wood, With Box storage with Manual lifting. The product should bear IGBC Green Pro certificate for product category.And should be BIFMA member having AIOTA (All India Occupational Therapists Association) forGUEST HOUSE FURNITURE range for ergonomic design. |
| 610 | Providing and Placing in position Bedside Table with two drawer. Overall size of the table shall be 450 W mm x 450 D mm x 450 H mm. Body and drawer panels of Bed side table are made of 18 mm thick Prelaminated Particle Board. All the exposed edges are edge banded with 0.8 mm thick PVC edge banding. .The product should bear IGBC Green Pro certificate for product category.And should be BIFMA member having AIOTA (All India Occupational Therapists Association) forGUEST HOUSE FURNITURE range for ergonomic design. |
| 611 | Providig and Placing in position Sofa Set.Sofa S57 Made Of Good Quality Products Of MSPL Standard Models. SeatWooden Structure Uphostered With Leatherite & HD Foam 32 Softy. SS Chrome . Sofa S57 Max. Height750mm .The rounded Armrests Provided Sleek And Stylish LookWith The Pillowed Back .Arm Rest Leatherite Covered With Solid Wood Structure . Understructure Made By Solid Wood Structures With Heavy Quality Spring For Maximum Comfort , Taper Type 25mm Round Spiral Spring. Legs Round Pipe Chrome Plated Legs. Understructure Made of Base Frame Strongly Jointed Wooden Plywood Parts.3 Seater SofaSeat Height From Ground460mm . 1950W x 760D x 750H, 2 Seater Sofa 1450W x 760D x 750H . Seat Height From Ground 460mm . 100mm High Legs .The product should bear IGBC Green Pro certificate for product category.And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design. 2 Seater Sofa 1450W x 760D x 750H . Seat Height From Ground 460mm |
| 612 | 1 Seater Sofa: 850 W mm x 760 D mm x 750 H mm with 460 mm Seat Height |
| 613 | Supplying & Fixing of METHODEX makeAlice CenterTable size 1200x600x450mmas per drawing & specification and directed by Engineer-in-Charge. The product should bear IGBC Green Pro certificate for product category.And should be BIFMA member having AIOTA (All India Occupational Therapists Association) forGUEST HOUSE FURNITURE range for ergonomic design. |
| 614 | Providing and Placing in position Dining Table. Dinning Table & Chair (1+6) SIX seater, in combination of seasoned solid wood , plywood & veneer with Melamine Polish, Productdimension Table: 2100W X 1050D X 750H,Chair:475W X 450D X 950H, chair foam thickness approx. 75mm thick, Glass on the table top. The product should bear IGBC Green Pro certificate for product category.And should be BIFMA member having AIOTA (All India Occupational Therapists Association) forGUEST HOUSE FURNITURE range for ergonomic design. |
| 615 | Providing and installing 18 mm HDHMR boards on existing RCC and cement plaster brick walls with the help of counter sink fasteners in plumb and level. All edges to be rounded. 1 mm laminate should be pasted on all visible areas and edges polished to match the laminate shade. |
AI Tender Summary
Tender Timeline
Dec 03, 2025
11:30 IST
Tender Published
Tender notice published.
Completed
Dec 04, 2025
18:00 IST
Corrigendum-1 Issued
Clarifications on tender conditions and amendments issued.
Completed
Dec 19, 2025
18:00 IST
Corrigendum-2 Issued
Clarifications on tender conditions and amendments issued.
Completed
Dec 19, 2025
18:00 IST
Corrigendum-3 Issued
Clarifications on tender conditions and amendments issued.
CompletedDec 19, 2025
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedDec 19, 2025
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender