Tender For Renovation Work Of Auditorium In Arc Building , University Of Delhi; 1 Disposal of moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting, unloading to approved municipal dumping ground for lead upto 10 km for all lifts, complete as per directions of Engineer-in-charge. 2 Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.All kinds of soil 3 Supplying chemical emulsion in sealed containers including delivery as specified. Clorpyriphos/ Lindane emulsifiable concentrate of 20%Chlorpyriphos/ Lindane emulsifiable concentrate of 20%Chlorpyriphos / Lindane emulsifiable concentrate of 20% 4 Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) :Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: With Chlorpyriphos/Lindane E.C. 20% with 1% concentration 5 Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) :Treatment of existing masonry using chemical emulsion @ one litre per hole at 300 mm interval including drilling holes at 45 degree and plugging them with cement mortar 1:2 (1 cement : 2 coarse sand) to the full depth of the hole :With Chlorpyriphos/Lindane E.C. 20% with 1% concentration 6 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level 1:1.5:3 (1 cement : 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size) 7 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) 8 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level 1:3:6 (1 cement : 3 coarse sand :6 graded stone aggregate 20 mm nominal size) 9 Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size) 10 Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to foor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size). 11 Centering and shuttering including strutting, propping etc. and removal of form for : Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. sqm 609.30 12 Centering and shuttering including strutting, propping etc. and removal of form for : Suspended floors, roofs, landings, balconies and access platform 13 Centering and shuttering including strutting, propping etc. and removal of form for : Lintels, beams, plinth beams, girders, bressumers and cantilevers sqm 552.05 14 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more. 15 Add for using extra cement in the items of design mix over and above the specified cement content therein. quintal 673.30 16 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand) 17 Brick work with common burnt clay machine moulded perforated bricks of class designation 12.5 conforming to IS: 2222 in superstructure above plinth level up to floor five level in cement mortar 1:6 (1 cement : 6 coarse sand) : With F.P.S.(non modular) bricks 18 Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundations and plinth in : cement mortar 1:4 (1 cement : 4 coarse sand) 19 Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level Cement mortar 1:4 (1 cement :4 coarse sand). 20 Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry. 21 Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Granite of any colour and shadeArea of slab upto 0.50 sqm 22 Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge Granite work 23 Extra for fixing marble /granite stone, over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive, including cleaning etc. complete. 24 Providing and fixing expandable fasteners of specified size with necessary plastic sleeves and galvanised M.S. screws including drilling holes in masonry work /CC/ R.C.C. and making good etc. complete. 50 mm long 25 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. 26 Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : 200x10 mm 27 Providing and fixing bright finished brass handles with screws etc. complete: 125 mm 28 Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete. 29 Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete. 30 Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer. M.S. tube 31 Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). 32 Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate 33 Cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement.18 mm thick 34 Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shadeof the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :25 mm thick 35 Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. 36 40 mm thick rubbed stone flooring over 20 mm (average) thick base of cement mortar 1:5 (1 cement : 5 coarse sand) with joints 3 mm thick, side buttered with cement mortar 1:2 (1 cement : 2 stone dust) admixed with pigment to match the shade of stone and pointing with same mortar. White sand stone 37 Extra for pre finished nosing in treads of steps of Kota stone/ sand stone slab. metre 148.10 38 Extra for Kota stone/ sand stone in treads of steps and risers using single length up to 1.05 metre. sqm 33.10 39 Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm 40 Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. each 244.05 41 Neat cement punning. 42 Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer’s specification.Two or more coats on new work 43 Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface :Water thinnable cement primer 44 Finishing walls with Acrylic Smooth exterior paint of required shade :New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) 45 Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work 46 Providing and applying white cement based putty of average thickness1 mm, of approved brand and manufacturer, over the plastered wallsurface to prepare the surface even and smooth complete 47 Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. Two coats 48 Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. 49 Raking out joints in lime or cement mortar and preparing the surface for repointing or replastering, including disposal of rubbish to the dumping ground within 50 metres lead. 50 Providing and fixing double scaffolding system (cup lock type) on the exterior side of building/structure, upto25 metre height, above ground level, including additional rows of scaffolding in stepped manner as per requirement of site, made with 40mm dia M.S. tube, placed 1.5 metre centre to centre, horizontal & vertical tubes joint with cup & lock system with M.S. Tubes, M.S. tube challis, M.S. clamps and staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for execution of work of cleaning and/ or pointing and/ or applying chemical and removing it thereafter. The scaffolding system shall be stiffened with bracings, runners, connecting with the building etc, wherever required, if feasible, for inspection of work at required locations with essential safety features for the workmen etc., complete as per directions and approval of Engineer-in-charge.Note:-(1)The elevational area of the scaffolding shall be measured for payment purpose. (2)The payment will be made once only for execution of all items for such works. 51 Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge.Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) 52 Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.In cement mortar 53 Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.For thickness of tiles 10 mm to 25 mm 54 Dismantling old plaster or skirting raking out joints and cleaning the surfacefor plaster including disposal of rubbish to the dumping ground within 50 metres lead. 55 Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. 56 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap 57 Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : 17.3.1 W.C. pan with ISI marked white solid plastic seat and lid 58 Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.Semi rigid pipe32 mm dia 59 Providing and fixing toilet paper holder :C.P. brass 60 Providing and fixing soil, waste and vent pipes : 100 mm diaSand cast iron S&S pipe as per IS: 1729 61 Providing and fixing single equal plain junction of required degree : 100x100x100 mm Sand cast iron S&S as per IS - 1729 62 Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors :100 mm inlet and 100 mm outletSand cast iron S&S as per IS: 3989 63 Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. each 158.55 64 Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design:100x100 mm size P typeWith common burnt clay F.P.S. (non modular) bricks of class designation 7.5 65 Providing and fixing roller blinds made of ROLLER BLACKOUT FABRIC of approved shade and colour of approved quality (such as Vista / Mac or equivalent), including all necessary fixtures, fasteners, brackets, and accessories, complete in all respects as per the direction of the Engineer-in-Charge. 66 Providing and fixing (PVC flooring of LG Hausys PVC FLOORS - 6 mm EQ FLOOR or equivalent ofPremier Polyfilm, Frogg Sports) approved quality 6mm thick as per the direction of Engineer-in-Charge 67 Providing and fixing tiled false ceiling of approved materials of size 595x595 mm in true horizontal level suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 gsm/sqm, both side inclusive) consisting of main T runner with suitably spaced joints to get required length and of size 24x38mm made from 0.30mm thick (minimum) sheet, spaced at 1200mm center to center and cross T of size 24x25mm made of 0.30mm thick (minimum) sheet, 1200mm long spaced between main T at 600mm center to center to form a grid of 1200x600 mm and secondary cross T of length 600mm and size 24x25mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600mm panel to form grids of 600x600mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, wherever, required, cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main T runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 x mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete at all heights as per specifications drawings and as directed by Engineer-in-charge.15mm thick mineral fibre acoustical suspended ceiling system with AMF RH 90 Medium Texture (BOARD Edge Tiles of size 595 x 595mm having Humidity Resistance (RH) of 90% of Armstrong of equivalent. 68 Providing and Fixing factory made uPVC door frame, made of uPVC exturded sections, of size 65 mm x 55 mm with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be mitred cut and jointed with plastic brackets and stainless steel screws, reinforcing hinge sidevertical of the frames with PVC profile of Size 28 mm x 30 mm having wall thickness 2 mm (±0.2 mm), including providing & fixing 3 nos of 125 mm long stainless steel hinges to the frame, fixing the frame with jamb with required number & size of anchor dash fastners, all complete as per manufacturers specification and direction of Engineer-in-charge 69 Providing and fixing factory made uPVC white colour sliding glazed door/window comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension uPVC extruded glazing beads, uPVC extruded interlock and uPVC extruded Inline sash adaptor (if required), EPDM gasket, wool pile, zinc alloy (white powder coated) handle with key on one side of extreme panels along with zinc plated mild steel multi point locking having transmission gear with keeps, zinc alloy (white powder coated) cresent lock (if required), stainless steel (SS 304 grade) body with adjustable double nylon rollers (weight bearing capacity to be 120 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardwares and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. 70 Providing and fixing glazing in Upvcdoor, window, ventilator shuttersand partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge.(Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 5.50 mm thickness 71 Providing and laying Micro Concrete of M-40 grade or equivalent material, blended with washed, saturated surface-dry (SSD), graded, low-absorption, high-density aggregates of size 10 mm and below up to 20% by weight of micro concrete, and water at 4 litres per 25 kg bag, and pouring into the formwork using a suitable pumping device for uniform flow of concrete. The side shuttering can be removed after 3 days and the bottom shuttering after 7 days, ensuring proper bond between the micro concrete and existing concrete substrate. The item rate is inclusive of all materials, labour, supervision, tools, tackles, transportation, curing, etc., complete as per specification and as directed. Formwork will be paid separately on the basis of the item of formwork 72 Providing & fixing in position wall paneling of thickness 25 mm with Fiber Glass creda Acoustical Wall Panels ((make Credence or equivalent of Armstrong, Anutone) model no. STR-P of size 600x1200 mm, resin bonded square edges having NRC of 0.9 minimum. The panels should be manufactured from high density bio-soluble resin bonded glass wool absorber having density of 96 Kgs/m3 and wrapped on the front side with an acoustically transparent fabric having option of colours and fabric type like jute etc. as per approved by architect/engineer-in-charge, plain tissue backer and fabric wrapped hardened edges. Panels should have humidity resistance up to 90%, thermal conductivity ≤ 0.03 (m² k / w) thermal resistance ≥ 0.9 (m² k/w) & moisture rate ≤ 1% (JC/T670-2005). The panel should be fully recycled and fire retardant as per Class A. The installation comprises a Gl framework for acoustic wall paneling as per design drawing (made from especially fabricated galvanized iron sheets 0.5 mm thick pressed section. galvanizing @ 120 grams per sqm including both sides) consisting of floor channel of size 50X32X32X0.5 mm thick bottom and top fixed with nylon sleeves and screw. Further vertical Gl studs of size 48X34X36X0.5 mm thick are placed at 600 mm center to center vertically on the wall using 12 mm dia 50 mm long wedged type expanded zinc alloy dash fastener with 10 mm bolt, to avoid any undulations on the wall. The extra channel must be used at openings and junctions as required. Further, wooden batten/ply of 6mm thickness and a width of 5 to be placed at 600 mm center to center horizontally on the vertical Gl Studs. Surface impalers of size 3X4 having projecting element called spikes shall be fixed on the wooden batten surface at 600 mm center to center horizontally and 1200 mm center to center vertically, using self-tapping screws. Silica based construction adhesive to be dabbed on to the projecting elements (spikes) of the impalers. Wall Panels shall be pierced through the spikes of the impalers ensuring line & level of panel are maintained. The panels should be mounted on the impalers horizontally or vertically as per the approved design or as per the directions of the engineer-in-charge. 73 Providing and fixing in position wall paneling of Wood Polymer Composite Acoustic panels (make Credence or equivalent of Armstrong, Anutone) westo of width 192, thickness of 15 mm and length 2440 mm made up of extruded WPC (Wood Polymer Composite) comprising of virgin Polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) having minimum density of up to 650 kg/m3, minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. The panels shall have a special perforation pattern of 3 mm groove & 21 mm pitch. The edges of the panels shall be tongued-and-grooved to receive special clips for installation. The panel shall paint polish (to be paid separately) as approved by the Engineer -in- Charge. The panel shall be mounted on special channels using clips as approved by the Engineer -in-charge. Install G.I stud of section 48X34X36 mm or as approved by the Engineer-in-Charge on the solid wall vertically using screws and plugs at spacing of 600mm centre-to-centre. Screw the aluminium channel (keel) horizontally on G.I stud 600mm centre to centre. Install the first set of wpc panels by inserting the clips vertically. For border channel insert the groove of the panel in to the projecting flange of the aluminium clip. Continue installing rows of panels by inserting the tongue into the groove of the earlier inserted panel and progressively installing clips for inside channel into the next aluminium channel (keel) and simultaneously fill the gap between wall & panel by 50 mm thick rock wool having density of 48 kg/m3. Continue the process till the actual height is achieved. Use clips for border channel to finish off the installation as approved by Engineer-in-Charge. The installed panels should give an NRC minimum of 0.9. 74 Providing and fixing of push back auditorium chair (Model no. Godrej Jupiter or equivalent ofCastor, Durian, Featherlite) fully upholsterd all complete including fitting and fixture as per design approved by Engineer-in-charge. 75 Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel / PVC conduit as required. 76 3x1.5 sq.mm 77 3x2.5 sq.mm 78 3x4 sq.mm 79 3x6sq.mm 80 Supplying and fixing following size/modules GI box along with modular base and cover plate for modular switches in recess etc asrequired. 81 3 Module (100mmX75mm) 82 6 Module (200mmX75mm) 83 12 Module (200mmX150mm) 84 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 85 5/6 amps switch 86 3 pin 5/6 amps socket outlet 87 15 /16 amps switch 88 6 pin 15/16 amp socket outlet 89 Supplying and fixing suitable size G.I. box with modular plate and cover in front or in recess including providing and fixing 25A modular socket outlet and 25A modular SP MCB C curve including connections, painting etc. as required. 90 Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS : 374- 2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required. 91 Rewiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable and 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable as earth wire in existing surface/ recessed steel /PVC conduit including dismantling as required.Group C 92 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group C 93 Supplying and fixing of Heavy duty PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 94 20 mm dia 95 25 mm dia 96 Supplying and fixing of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required. 25 MM 97 Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned cop per bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 12 way ( 4 + 36 ) double door 98 Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, “C” curve, miniature circuit breaker suitable for inductive load of single pole MCB in the existing MCB DB complete with connections, testing and commissioning etc. as required. 99 Single pole 100 Triple pole 101 Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.63 A 102 Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63 Amp 103 Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required. 104 Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required. 105 Providing and fixing 6 SWG dia G.I. wire on surface or in recess forloop earthing as required. 106 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed Heavy duty PVC conduit as required.4 x 16 + 2 x 6 sqmm 107 Providing and 125 amps, 16 KA, TPMCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required 108 Providing and fixing 200 A, 25 KA,TPMCCB rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required. 109 Supplying and fixing 2 module stepped type fan regulator on the existing modular plate switch box including connections but excluding modular plate etc as reqd. 110 Supply, Installation, testing and commissioning of pre wired 2x2 recess mounted 36 watts LED fitting square shape, Industrial grade with luminaire with diffuser complete with all accessories i/c connection with 1.5 sqmm FRLS PVC copper conductor Cable with mounting 4 nos clutch wire /G.I. chain for mounting from true ceiling etc. as required. Make Philips, Model No. - FullGlow G6Cat No. RC380B LED36S-6500 G6 L60W60 PSU OD S1 or equivalent model of Thorn/Trilux 111 Supply, Installation, testing and commissioning of 15 watt, LED downlighter, Industrial grade, 220-240 V, 50 Hzcomplete i/c all accessories etc. recesses mounted including connection with 1.5 sq. mm FRLS PVC insulated, copper conductor cable and earthing etc. as required. Make Philips, Model No. - GreenPerform Sleek G2 Cat No. DN296B LED15S-6500 PSE WH S2 or equivalent model of Thorn/Trilux 112 Supplying of one no XLPE insulated and PVC sheathed aluminium conductor armoured power cable of 1.1 KV grade of size 4CX16 Sqmm etc. complete as required. 113 Supplying of one no XLPE insulated and PVC sheathed aluminium conductor armoured power cable of 1.1 KV grade of size 3.5CX35 Sqmm etc. complete as required. 114 Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required.Upto 35 sq. mm (clamped with 1mm thick saddle) 115 Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required. Upto 35 sq.mm 116 Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 117 150 mm width X 50 mm depth X 1.6 mm thickness 118 300 mm width X 50 mm depth X 1.6 mm thickness 119 Supplying, installation , testing and commissioning of Air cooled ductable type Packaged air-onditioning units complete with Hermetically sealed Scroll compressors fitted inside the indoor unit & first charge of refrigerant R410A or equilant permitted green refrigerant & oil ,air cooled condenser, fan section with statically/dynamically balanced centrifugal blower driven by a Totally Enclosed Fan Cooled (TEFC) squirrel cage three speed motor, Multi rows cooling coil of copper with aluminum fins etc. The enclosures shall be fabricated of M.S. The Package unit shall be equipped with synthetic fiber filter, insulated drain pan, controls all encased in a unit. The casing shall be factory powder coated. Electrical panel board for Package units shall comprise of control and power panel with including all associries i/c Voltage scanner, overload, low voltage, high voltage & phase imbalance protection, along with VI Pads complete with all ancillaries including MS painted stand for Outdoor units of suitable size, foundation and allied minor civil works as per instructions of Engineer-in-charge of following ratings including electric control panel & fitting as per CPWD specifications and as per IS: 8148 complete as required. Unit shall be installed at terrace and should be suitable for outdoor operation. 22.0TR (2.8 EER) 120 Supply, installation, balancing and commissioning of factory fabricated GSS _ sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes,hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required. 121 Thickness 0.63 mm sheet 122 Thickness 0.80mm sheet 123 Thickness 1.00 mm sheet 124 Supplying, fixing testing commissioning of supply air diffusers of powder coated aluminium with aluminium volume control dampers with anti smudge ring & removable core. 125 Supplying, fixing testing commissioning of Return air diffusers of powder coated aluminium without volume control dampers with anti smudge ring & removable core. 126 Supplying, Fixing,testing and commissioning of fire dampers in supply air duct/main branch and return air path as and where required of required sizes i/c control wiring,the damper shall be motorized and spring return so as to close the damper in the event of power failure automatically and open the same in case of power being restored. The spring return action shall be inbuilt mechanism and not externally mounted. The damper shall also be closed in the event of fire signal complete as required and as per specifications. 127 Fire Damper 128 Actuator 129 Supplying and fixing of following thickness duly laminated aluminum foil of mat finish closed cell Nitrile rubber (Class O) insulation on existing duct after applying suitable adhesive for Nitrile rubber. The joints shall be sealed with 50 mm wide and 3 mm thick self adhesive nitrile rubber tape insulation complete as per specifications and as required. above. Valves should have pressure rating of 25 Bar minimum. 19 mm 130 Supplying and fixing 50mm thick aluminium foil faced resin bonded fibre glass insulation (on duct) of density 24 kg/cu.m or mineral wool insulation(non combustible) of density 44 kg/cum after applying two coats of cold setting adhesive (CPRX compound) sealing all joints with self adhesive aluminium tape & covering with 0.63mmx19mm Gl wire mesh netting & butting all joints and laced with GI wire complete and finally covered with one layer of tar felt stuck with hot bitumen as per specifications and as required. (for outdoor applications) 131 Supplying, fixing, testing and commissioning of butterfly valve of PN1.6rating with bronze/gunmetal seat duly ISI marked complete withnuts,bolts, washers, gaskets conforming to IS 13095 of followingsizes as required :100 mm dia 132 Providing, installation, testing and commissioning of stainless steelY-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange.100mm dia 133 Providing, fixing, testing & commissioning of 15mm dia quartzoidbulb type sprinklers of rating 68 degree centigrade with requiredaccessories : 134 Pendent Sprinkler 135 Upright Sprinkler 136 Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875(Burst) with branch line (Inlet) 25mm NPT male thread tosprinkler head(Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizescomplete as reauired.1200mm 137 Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required. 138 Providing and fixing in position the industrial type pressure gauges with gun metal / brass valves complete as required 139 Providing, installation, testing & commissioning of adjustable rosette plate 15mm dia in white finish UL Listed or FM approved complete as required. 140 Providing & fixing flow switch in following sizes M.S. pipe including connection etc as required. 100 mm Dia 141 Providing, fixing, testing & commissioning of installation control valve of cast iron body, brass/bronze working parts comprising of water motor alarm, bronze seat clapper, clapper arm and hydraulically driven mechanical gong bell to sound continuous alarm when the wet riser/sprinkler system activates, pressure gauges, emergency releases, strainer, pressure switch, cock valve completewith drain valve and bypass, test control box, ball valves, MS pipe of required size, flanges, orifice plate, gasket etc of follwing sizes as required 100 mm Dia 142 Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and painting with synthetic enamel paint of approved shade as required. 143 Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required: Gun Metal 144 Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with Gl wire, rivets etc. conforming to IS 636 (type-A) as required : Stainless Steel (Grade 304) 145 Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required.20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket. 30m 146 Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required : Single headed Stainless steel 147 (A) Supplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump)(B) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical confirming to IS : 1520(C) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horiziontal foot mounted type with Class-F insulation, conforming to IS-325.(D) M.S. fabricated common base plate, coupling, coupling guard, foundation bolts etc. as required.(E) Suitable cement concrete foundation duly plastered and with anti vibration pads. 148 900 Ipm at 35 m Head 149 Supply, Installation, testing and commissioning of (7.5-10) HP, Direct on line starters suitable for fire fighting pump with sheet steel enclosures, 3-phase, 440V, complete set with contractor & OLR,single phase preventer,start, stop push button with indicator lamps, voltmeter, ammeter, suitable for automatic operation with command from pressure switch including mountig arrangement od starter with all accessories etc. as required. This starter shall be suitable for the firefighting pump described aove. 150 Providing, laying, testing & commissioning of C class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame andpainting with two or more coats of synthetic enamel paint of required shade complete as required : 151 25 mm dia 152 32 mm dia 153 80 mm dia 154 100 mm dia 155 Supplying, installation, testing and commissioning of micro processor based intelligent addressable main fire alarm panel, central processing unit with the following loop modules and capable of supporting not less than 240 devices (including detectors) and minimum 120 detectors per loop and loop length up to 2 km, network communication card, minimum 320 character graphics/ LCD display with touch screen or other keypad and minimum 4000 events history log in the non volatile memory (EPROM), power supply unit (230 + 5 % V, 50 hz), 48 hrs back-up with 24 volt sealed maintenance free batteries with automatic charger. The panel shall have facility to connect printer to printout log and facility to have seamless integration with analog/digital voice evacuation system (which is part of the schedule of work under SH: PA System) and shall be complete with all accessories . The panel shall be compatible for IBMS system with open protocol BACnet/ Modbus over IP completeas per specifications. 156 Two Loop Panel. 157 Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector complete with mounting base complete as required. 158 Supplying, installation, testing & commissioning of response indicator on surface/recessed MS Box having two LED, metalliccover complete with all connections etc as required. 159 Supplying, installation, testing & commisssioning of intelligent addressable programmable sounder complete as required. 160 Supplying, installation, testing & commissioning of intelligent addressable thermal detector with rate of rise cum _ fixed tempreature thermistor complete with base as required. 161 Supplying, installation, testing & commissioning of addressable beam detector with short circuit isolator (inbuilt or seperate) complete with emitter and receiver including connections with remote test features etc complete as required. 162 Supplying, installation, testing & commissioning of addressable manual call point complete as required. 163 Supplying, installation, testing & commissioning of addressable horn cum strobe complete as required. 164 Supplying & laying of 2x1.5 sqmm fire survival armoured cable, 600/1000V rated with annealed copper conductor having glass mica fire barrier tape covered by an extruded layer of Cross Linkable Ethylene Propylene Rubber (EPR) insulation and LSZH _ inner bedding, steel wire armouring & LSZH outer sheath complete as required. 165 Supply, Installation, Testing and Comissioningof Biamped, coaxial two-way point source loudspeaker with a single 12 LF driver and compression driver with 3 or better Voice coil. Frequency Range (-10dB) of 60Hz - 20kHz or better& long term Continuous Power Handling of 300W (Low frequency) and 45W for High Frequency driver or better. The Loudspeaker module shall have a Max. SPL (Peak) of MF/HF>= 131 or better. It should have Horizontal dispersion pattern of 110º or better, vertical dispersion of the loudspeaker shall be 60 degrees or better. The loudspeaker shall be enclosed in a Baltic birch plywood enclosure with perforated steel grille, compact, two-way loudspeaker with a 12-inch woofer and 3-inch compression driver, featuring a 110° x 60° nominal coverage pattern, 70-18,000 Hz frequency response (±3 dB), 300W continuous passive power handling, and a peak SPL of 131 dB. It can be used in passive or bi-amp mode, has a Baltic birch plywood enclosure, an M10 mounting system, and a 35° tilt-back angle for monitor use etc. complete as required. SITC of loudspeaker hanging arrangement from true ceiling, customised as per site requirement is included in this item. Make - Bose, Cat No- AMM112 or Equivalent make of Martin Audio/EWA. 166 Supply, Installation, Testing and Comissioningof Multipurpose subwoofer with a single 15 neodymium LF driver. Frequency Range (-10dB) of 35Hz - 130Hz or better& long term Continuous Power Handling of 500W or better. It should have an axial Sensitivity of > = 90dB (1W/1m) or more delivering a free field Max. Calculated SPL(peak) of>=124db or better. The loudspeaker should have a nominal impedance of 8 ohm or more. The loudspeaker shall be enclosed in a Baltic birch plywood enclosure with perforated steel grille.Complete with installation as per the site requirement.ompact 15-inch subwoofer with a 500 W continuous power handling (2800 W peak), an 8-ohm impedance, and a frequency range of 35 Hz to 130 Hz. Key features include a single 15-inch neodymium woofer, integrated M20 pole mount, M10 suspension points, and caster mounting points, all within a Baltic birch plywood enclosure etc. complete as required. SITC of subwoofer hanging arrangement from true ceiling, customised as per site requirement is included in this item. Make - Bose, Cat No- AMS115 or Equivalent make of Martin Audio/EWA. 167 Supply, Installation, Testing and Commissioning of Two-way Small Format high SPL IP55 rated (as per IEC 60529) all weather surface mount loudspeaker. The loudspeaker shall meet the following performance criteria: Frequency Range (-10 dB) of 90 Hz - 18 kHz or better; Nominal Dispersion: 100°H x 100°V; Power handling of 400W peak or more; Sensitivity: 90 dB and the Max SPL : 118dB Peak or better; Nominal impedance of 8 ohms and Integral multi-tap Transformer with selectable tap settings of 10/20/40/80W@70V & 100V. The loudspeaker system shall be comprised of a Powder-coated finish stainless steel grille with Two-part spray polyurea coating Enclosure;Single 5.25-inch woofer; Single 2-inch voice coil high-frequency compression driver; U bracket shall be included. high-performance speaker with a 5.25 LF driver, a horn-loaded compression driver, 100W continuous/400W peak power handling, 100° x 100° coverage, and an 8-ohm nominal impedance. It is designed for outdoor and indoor commercial applications, is weather-resistant, and offers transformer taps for 70V and 100V systems etc. complete as required. Make - Bose, Cat No- AMU105 or Equivalent make of Martin Audio/EWA. 168 SITC of Active Portable loudspeaker system with 2 combo XLR-1/4 inputs, 3.5 mm input, Bluetooth inputs and 1/4 TRS line outputwith 11 hours of play time using the rechargeable lithium ion battery with Freq Response 62Hz - 17kHZ and 109dB peak SPL, 120 H x 50V Nominal coverage, portable wireless PA system featuring a 3-channel mixer with ToneMatch processing, a 3.5mm aux input, and two XLR/1/4 combo jacks, along with Bluetooth 5.0 connectivity for music streaming and wireless setups. It has a rechargeable lithium-ion battery providing up to 11 hours of operation, an auto-rotating EQ for optimal sound in any orientation, and can be placed on a pole mount or used as a floor monitor. Key specifications include a frequency response of 62Hz–17kHz, a maximum SPL of 103 dB, and a 120° H x 50° V coverage pattern, with a weight of 14.4 lbs (6.5 kg). Make - Bose, Cat No- S1 PRO+ or Equivalent make of Martin Audio/EWA. 169 Supply, Installation, Testing and Comissioningof Class D amplifier with2x600 WLoad-independent outputs deliver full channel power to either low-impedance (4-8 Ω) or high-impedance (70/100V) loads without bridging .Amplifier shall havefrequency response of 20 Hz to 20 kHz (+/- 1 dB) for LZ mode,with THD+N at rated power less than 0.04%.The amplifier shall meet or exceed the following performance specifications: channel separation (crosstalk) greater than 80 dB below rated power at 1 kHz. The amplifier shall have2 line-level inputs with selectable input sensitivity settings ( -10 dBV, 4 dBu and 14 dBu)for balanced line-level inputs (6-pin Euroblock connector) andpossibility of4or more no .ofdigital Audio channels . The amplifier shall offer a master mute connection for use with external dry contacts, normally open or normally closed, to mute all outputs of the amplifier etc. complete as required. Make - Bose, Cat No- P2600A or Equivalent make of Martin Audio/EWA. 170 Supply, Installation, Testing and Comissioningof Class D amplifier with2x1000 WLoad-independent outputs deliver full channel power to either low-impedance (4-8 Ω) or high-impedance (70/100V) loads without bridging .Amplifier shall havefrequency response of 20 Hz to 20 kHz (+/- 1 dB) for LZ mode,with THD+N at rated power less than 0.04%.The amplifier shall meet or exceed the following performance specifications: channel separation (crosstalk) greater than 80 dB below rated power at 1 kHz..The amplifier shall have2 line-level inputs with selectable input sensitivity settings ( -10 dBV, 4 dBu and 14 dBu)for balanced line-level inputs (6-pin Euroblock connector) andpossibility of4or more no .ofdigital Audio channels. The amplifier shall offer a master mute connection for use with external dry contacts, normally open or normally closed, to mute all outputs of the amplifier etc. complete as required. Make - Bose, Cat No- P21000A or Equivalent make of Martin Audio/EWA. 171 Supply, Installation, Testing and Comissioningof Class D amplifier with4x300 WLoad-independent outputs deliver full channel power to either low-impedance (4-8 Ω) or high-impedance (70/100V) loads without bridging .Amplifier shall havefrequency response of 20 Hz to 20 kHz (+/- 1 dB) for LZ mode,with THD+N at rated power less than 0.04%.The amplifier shall meet or exceed the following performance specifications: channel separation (crosstalk) greater than 80 dB below rated power at 1 kHz..The amplifier shall have2 line-level inputs with selectable input sensitivity settings ( -10 dBV, 4 dBu and 14 dBu)for balanced line-level inputs (6-pin Euroblock connector) andpossibility of4or more no .ofdigital Audio channels. The amplifier shall offer a master mute connection for use with external dry contacts, normally open or normally closed, to mute all outputs of the amplifier etc. complete as required. Make - Bose, Cat No- P4300A or Equivalent make of Martin Audio/EWA. 172 Supply , installation , testing and commissioning of IntegratedDigital SoundProcessor with following functionalities and specifications; Signal Processor shall be CPU-32-bit fixed/floating-point DSP + ARM, 456 MHz. The DSP shall have8 Mic/Line inputs & 8 analog outputs, 8 Additional digital Outputs; Audio Latency 860 μs (analog in to analog out) or less,24 Bit A-D and D-A Convertors; Sampling Rate : 48 kHz;THD : < 0.002 % ; Channel Separation (Crosstalk) : < -105 dB ; Frequency Response 20 Hz - 20 kHz ; Dynamic Range :> 115 dB; Phantom Power +48 VDC,selectable per input, 5 Control Inputs and Outputs; RS-232 and Ethernet Port for third party Control and Monitoring;inbuilt DSP features like automatic mic mixing, multiband graphic and parametric EQs,signal generators, routers, mixers, AGCs, duckers, gates, compressors, source selectors, and delays. etc. Shall Support at least 15 remote Zone controllers etc. complete as required. Make - Bose, Cat No- ESP-880A or Equivalent make of Martin Audio/EWA. 173 Supply, installation, testing & Commissioning ofSound Reinforcement System - Networked and programmable controller; Power supply requirement of 15-24 VDC, 300mA; Four rotatory encoders with circular LED rings for managing gain setting or scene selection; Fifth encoder provides control over programmed scenes or presets; Two line by 40 character blacklit LCD provides names of the system elements they are controlling etc. complete as required. Make - Bose, Cat No- CC-64+PS1 or Equivalent make of Martin Audio/EWA. 174 Supply, Installation, Testing and Comissioningof Gooseneck mic with mute button, Element Fixed-charge back plate, permanently polarized condenser Polar Pattern Cardioid, Frequency Response 70-16,000 Hz, Open Circuit Sensitivity -37 dB (14.1 mV) re 1V at 1 Pa, Maximum Input Sound Level 134 dB SPL, 1 kHz at 1% T.H.D etc. complete as required. Make - AudioTechnica, Cat No- Pro49qle+AT8668s or Equivalent make of Shure/sennheiser/AKG 175 Supply, Installation, Testing and Comissioningof Wireless lapel mic, Element Condenser Polar Pattern Cardioid, Cable 55 (1.4 m) Cable permanently attached to mic, Dimensions 24mm long, 10.5mm diameter etc. complete as required. Make - AudioTechnica, Cat No- PAT-829CW or Equivalent make of Shure/sennheiser/AKG 176 Supply, Installation, Testing and Comissioningof Wireless Handheld Transmitter System – Simple to set up and use, 2 x 4 channel frequency plan for enhanced flexibility, Rack mountable for easy installation and Intuitive receiver and transmitter controls, Operating Frequencies F-Band: 824 – 831 MHz, 863 – 865 MHz, Modulation Mode FM Frequency Response 60 Hz – 16 kHz, Frequency Stability +/- 0.005%, Phase lock loop frequency control Operating Range 60m, typical etc. complete as required. Make - AudioTechnica, Cat No- ATW-13HH2 or Equivalent make of Shure/sennheiser/AKG 177 Supply, Installation, Testing and commissioning of Black anodized, table mic stands., EIC approved (Make & Model PROELMic stand) etc. complete as required. 178 Supply, Installation, Testing and Comissioningof Mixer for live stage mics as per the no. of mics, 24 Mic Inputs with 48V Phantom Power and HPF per Channel · 32 Line Inputs (24 mono and 4 stereo) · 6 AUX Sends + 2 FX Sends · 4 GROUP Buses, 32 channels, including 24 XLR mic inputs with HPF and phantom power, and 8 stereo line inputs. Key features include onboard SPX digital multi-effects, a 31-band graphic equalizer on the stereo bus, and iOS device integration for remote control via the MGP Editor app etc. complete as required. Make - Yamaha or Equivalent make of Behringer/ Sound Craft 179 Supply and laying of 2 core 14 AWG/2.5 Sq mm, Twisted, unshielded Speaker cable with stranded annealed bare copper conductors, Semi-rigid PVC insulation, NEC CL3R, CEC CMG, RoHS compliant (Make & Model Liberty AV 14-2C-BLK) etc. complete as required. 180 Supply and laying 2 core Twisted, shielded balanced Audio and control cable with 22AWG or better 7 strand annealed bare copper conductors, Semi-Rigid PVC insulation, Riser rated PVC jacket. UL 444, UL 13 CMR rated etc. complete as required. 181 Supply and fixing of Floor Box for Stage etc. complete as required. 182 Supply and fixing of Mic port connectivity plates etc. complete as required. 183 Supply and fixing of Equipment 24U rack with all accessories as required for terminations (Make & Model Dlink 24U) etc. complete as required. 184 Supply installation testing and commissioning of CE Certified 100W LED PARCAN Light with latest RDM technology for user friendly operation andspecifications like Light SourceSingle COB LED Source, Color Temperature : 3200K with CRI & TLCI Value > 90, Power cable: 3 core 1 sq. mm. copper PVC insulated, Channels: 1/2 DMX-512 Channel Modes, Beam angle: 9°/15°/20°/25°/30° Manually Selectable, Control mode: RDM, DMX512 & Manual, Master/Slave, Auto run, Fully RDM Compliant in DMX Mode for the Lighting Console mentioned in this project,LUX @ 2m: > 36,000 @ 9° Beam Angle, Dimming: 0 - 100% Electronic Dimming, Function: Strobe, Dimming, Housing : Spun Aluminium Housing with black epoxy polyster powder coated finish, Accessory slot for Gel frame should be available or else fixture will be rejected., Power and DMX: Loop in and loop out compulsary, DMX in & Out Through : 5 Pin XLR connectors, Certification: CE / BISh etc. complete as required. Make - Canera Lighting, Cat No- CAN LED PARCAN 100 or Equivalent make of Leksa Lighting/Show Tec 185 Supply installation testing and commissioning of CE Certified 400W LED Blinder Effect Light with latest RDM technology for user friendly operation with specifications like Light Source : Quad LED COB Source, Power Factor : >0.95 @ 230V AC 50Hz, Color Temerature : 3200K, CRI & TLCI Value > 95, Power cable: 3 core 1 sq. mm. copper PVC insulated, Channels: 4/8 DMX-512 Channel Modes, Beam Angle : 40°, Control mode: RDM, DMX512 & Manual, Master/Slave, Auto run, Fully RDM Compliant in DMX Mode for the Lighting Console mentioned in this project, Lux output at 2 Mtr : > 8,500 Lux@ 40°, Dimming: 0 - 100% Electronic Dimming, Power and DMX: Loop in and loop out compulsary, DMX in & Out Through : 5 Pin XLR connectors andCertification: CE / BIS etc. complete as required. Make - Canera Lighting, Cat No- CAN LED BLDR 400 or Equivalent make of Leksa Lighting/Show Tec 186 Supply installation testing and commissioning ofCE Certified 54 x 3W LED PAR Light with latest RDM technology for user friendly operation with specifications like Base Color RGBW Color Mixing, LED Configuration : Multiple Nos Individual RGBW LED Configuartion, Power cable: 3 core 1 sq. mm. copper PVC insulated, Channels: 8 DMX-512, Beam angle: 15°, Control mode: RDM, DMX512 & Manual, Master/Slave, Auto run, Sound Active, Fully RDM Compliant in DMX Mode for the Lighting Console mentioned in this project, LUX @ 2m: >10,500 @ 15° Beam Angle, Dimming: 0 - 100% Electronic Dimming, Function: strobe, dimming, sound active and Master slave, Housing: Die Casted Aluminium or Metal Housing with black epoxy polyster powder coated finish, Power and DMX: Loop in and loop out compulsary, DMX in & Out Through : 5 Pin XLR connectors and Certification: CE / BIS etc. complete as required.Make - Canera Lighting, Cat No- CAN LED PAR 543 or Equivalent make of Leksa Lighting/Show Tec 187 Supply and fixing of CE Certified 100W LED Profile Spot Light with latest RDM technology for user friendly operation withspecifications like Light Source : Single LED COB Source, Color Temerature : 3200K, CRI & TLCI Value > 95, Power cable: 3 core 1 sq. mm. copper PVC insulated, Channels: 1/2/3 DMX-512 Channel Modes, Beam Angle : 19° or 15°, Control mode: RDM, DMX512 & Manual, Master/Slave, Auto run, Fully RDM Compliant in DMX Mode for the Lighting Console mentioned in this project, Lux output at 2 Mtr : > 15,000 Lux@ 19° or 15°, Dimming: 0 - 100% Electronic Dimming • 4 Beam shaping shutters, Accessory slot for Gobo and gobo holder, Iris & Color Frame should be available or else fixture will be rejected, Housing: Metal Housing with black epoxy polyster powder coated finish or PVC Body with matt black finish, Power and DMX: Loop in and loop out compulsary, DMX in & Out Through : 5 Pin XLR connectors and Certification: CE / BIS etc. complete as required. Make - Canera Lighting, Cat No- CAN LED PRO 119 or Equivalent make of Leksa Lighting/Show Tec 188 Supply installation testing and commissioning ofCE Certified 54 x 3W LED PAR Light with latest RDM technology for user friendly operation with specifications like Base Color 3200K Color Mixing, Color Temperature : 3200K with CRI > 90, LED Configuration : Multiple Nos Individual 3200K LED Configuartion, Power cable: 3 core 1 sq. mm. copper PVC insulated, Channels: 1 DMX-512, Beam angle: 15°, Control mode: RDM, DMX512 & Manual, Fully RDM Compliant in DMX Mode for the Lighting Console mentioned in this project, LUX @ 2m: >7,500 @ 15° Beam Angle, Dimming: 0 - 100% Electronic Dimming, Function: strobe, dimming, sound active and Master slave, Housing: Die Casted Aluminium or Metal Housing with black epoxy polyster powder coated finish, Power and DMX: Loop in and loop out compulsary, DMX in & Out Through : 5 Pin XLR connectors and Certification: CE / BIS etc. complete as required. Make - Canera Lighting, Cat No- CAN LED PAR 543T or Equivalent make of Leksa Lighting/Show Tec 189 Supply installation testing and commissioning of150W LED Sharpy moving head Light with RDM protocol and Hi grade plastic body black color with specifications like LED : 150WCool White LED, Beam Angle : 2°, Power Consumption : 150W ± 10%, Light Out put : >50,000 Lux at 2 Mtrs, Color Wheel : Minimum 14 Colors and open or More, Fixed Gobo Wheel : Minimum 14 Fixed Gobos or More, Prism : 8+16 facet prism, User Interface : 4 Nos High Precision Membrane type selector switch with LCD Display, Fully RDM Compliant when in DMX mode, Dimming : 0 to 100% 16 Bit Linear Dimming, DMX data IN / OUT: 5 pin locking XLR, Cooling system with low noise fan for forced ventilation, 3 Mtr 3 core 1 mm² FRLS & ISI mark cable with 3pin IEC Male Plug with proper earthing, 3 mtr DMX loop cable with cable mount 5 pin locking XLR and CE Certificate should be enclosed to ensure the required quality and safety of the products etc. complete as required. Make - Canera Lighting, Cat No- CAN LED MH 150SA or Equivalent make of Leksa Lighting/Show Tec 190 Supply and fixing ofDie cast Aluminium C - Clamp with safety chain duly epoxy polyester powder coated in black matt texture finish and safe working load of 100kg withspecifications like Lock - MS threaded Galvanized lock key, Plastic Glass filled nylon moulded M6 key, Receptacle - 28mm standard TV spigot, Safety - MS Galvanized chain with pin, Finish - Pretreated and black epoxy polyester powder coated and Self-weight - 0.54Kg etc. complete as required.Make - Canera Lighting, Cat No- ACC-10 or Equivalent make of Leksa Lighting/Show Tec 191 Supply and fixing of Safety bond with lock clip 1.5 Mtr Long made with twisted pair of GI wire rope, minimum 2mm Thickness with sleeve to be fixed around the grid to avoid fall of the material in case if the C clamp is not locked properly. SWL 150Kgs etc. complete as required.Make - Canera Lighting, Cat No- SB-15 or Equivalent make of Leksa Lighting/Show Tec 192 Supply and fixing ofFixed Stage Light Bar, length 5 Mtrs made using MS 40NB Class ‘B’ Pipe dual barrel construction arrangement undergone through various chemical treatment to keep them rust free and duly epoxy polyester powder coated in black matt texture finish with Specifications like Dual barrel Light bar equipped with 40x75x40 Cable trenching arrangement with lid for better aesthetic look and cable safety, Dual barrel pipe construction welded with 75x6mm MS Flat in every 1 Mtr for better strength and With Suitable Suspenders to fix the light bar with every 2mtr pitch etc. complete as required.Make - Canera Lighting, Cat No- FLB-05M or Equivalent make of Leksa Lighting/Show Tec 193 Supply and fixing of Fixed FOH Stage Light Bar, length 6 Mtrs made using MS 40NB Class ‘B’ Pipe dual barrel construction arrangement undergone through various chemical treatment to keep them rust free and duly epoxy polyester powder coated in black matt texture finish with Specifications Dual barrel Light bar equipped with 40x75x40 Cable trenching arrangement with lid for better aesthetic look and cable safety, Dual barrel pipe construction welded with 75x6mm MS Flat in every 1 Mtr for better strength and With Suitable Suspenders to fix the light bar with every 2mtr pitch etc. complete as required.Make - Canera Lighting, Cat No- FLB-06M or Equivalent make of Leksa Lighting/Showtec 194 Supply and fixing of MS Fabricated 4 way 10A, 250V A.C, IEC, Lighting Junction box made up of 22SWG CRCA for LED lighting fixtures with Pipe clamp arrangement for fixing on pipe grid or Raul plug arrangement for wall/floor fixing, duly black epoxy polyester powder coated texture finish etc. complete as required. Make - Canera Lighting, Cat No- JB-410IEC or Equivalent make of Leksa Lighting/Showtec 195 Supply and fixing of MS Fabricated 2 way 10A, 250V A.C, IEC,Junction box made up of 22SWG CRCA with rocker switch to power up splitter and console with Pipe clamp on pipe grid arrangement for fixing or Raul plug arrangement for wall/floor fixing, duly black epoxy polyester powder coated texture finish etc. complete as required.Make - Canera Lighting, Cat No- PSB-210IEC or Equivalent make of Leksa Lighting/Showtec 196 Supply and fixing of MS Fabricated 5 pin DMX Signal IN Junction box fitted with 5 pin DMX Male socket, junction boxmade up of 22SWG CRCA, with Pipe clamp on pipe grid arrangement for fixing or Raul plug arrangement for wall/floor fixing, black epoxy polyester powder coated, duly black epoxy polyester powder coated texture finish etc. complete as required. Make - Canera Lighting, Cat No- DMX-IBM5 or Equivalent make of Leksa Lighting/Showtec 197 Supply and fixing of MS Fabricated 5 pin DMX Signal OUT Junction box fitted with 5 pin DMX female socket, junction box made up of 22SWG CRCA, with Pipe clamp on pipe grid arrangement for fixing or Raul plug arrangement for wall/floor fixing, black epoxy polyester powder coated, duly black epoxy polyester powder coated texture finish etc. complete as required. Make - Canera Lighting, Cat No- DMX-OBF5 or Equivalent make of Leksa Lighting/Showtec 198 Supply, installation, testing and commissioning of Fabricated 5 pin DMX Signal loop Junction box fitted with 5 pin DMX Male & Female socket with 0.3 Mtr DMX Loop cable fitted with 5 pin DMX cable mount plug, junction boxmade up of 22SWG CRCA, with Pipe clamp on pipe grid arrangement for fixing or Raul plug arrangement for wall/floor fixing, black epoxy polyester powder coated, duly black epoxy polyester powder coated texture finish etc. complete as required.Make - Canera Lighting, Cat No- DMX-WLB5 or Equivalent make of Leksa Lighting/Showtec 199 Supply, installation, testing and commissioning of Well designed 6 Way Direct lighting/power Distribution Board made up of CRCA sheet undergone through 7 tank process with various chemical treatment to keep them rust free, duly powder coated with Matt texture finish consists of R, Y, B Indicator lamp, suitable size MCB at incomer and outgoing, junction boxes fixed on the top of the light bar including wiring and busbar connection with proper earthing and Hingable door with magnetic door lock complete etc. complete as required.Make - Canera Lighting, Cat No- DLDB-06 or Equivalent make of Leksa Lighting/Showtec 200 Supply, installation, testing and commissioning of Auxiliary marshalling box for power and signal cable termination in grid level and in Motorised Light bar CE Marked FC/PG cable entry gland required Nos as per cable entry, MS channel arranging to fix terminal connector, required nos with separation plate and each end is completed with adding end plate with end cap, Grey terminal connector with each line having P, N, E Indication for each line incoming and out going cable connectors, Box door must be made with Hingeable door with screw lock, Made up of 20SWG CRCA sheet undergone through 7 tank process with various chemical treatment to keep them rust free, duly epoxy polyester powder coated with Matt black texture finish etc. complete as required.Make - Canera Lighting, Cat No- AMB or Equivalent make of Leksa Lighting/Showtec 201 Supply, installation, testing and commissioning of RDM Compatible DMX Splitter unit with Minimum following specifications like 1 Nos 5 Pin DMX In socket and 8 Nos 5 Pin DMX Out socket, In and out signal Optically Isolated, LED Indicator for check the signal flow in output,Suitable for standard 19” cabinet and Duly black epoxy polyester powder coated texture finish etc. complete as required. Make - Canera Lighting, Cat No- CS-81 or Equivalent make of Leksa Lighting/Showtec 202 Supply, installation, testing and commissioning of Digital Lighting Console with Ultimate portability, offering a powerful LED and moving light controller in a small 19” unit with direct access to each of the lights, 1024 DMX Channel, LDC Screen for easy Navigation, DMX compatible, Control up to 96 LED, moving lights and conventionals individuals and multi-function faders etc. complete as required.Make - Canera Lighting, Cat No- CANDX-C96 or Equivalent make of Leksa Lighting/Showtec 203 Supply, installation, testing and commissioning of MS perforated tray of Size 40 x 75 x 40mm & 1.6 mm Thickness undergone through 7 tank process with various chemical treatment to keep them rust free, duly epoxy polyester powder coated with Matt black texture finish along with clamping arrangement etc. complete as required. Make - Canera Lighting, Cat No- PCTL-0752 or Equivalent make of Leksa Lighting/Showtec 204 Supply and laying of FRLS Grade DMX Signal 4 core + Ground shieldingCable with CE mark for the Signal network on existing cable tray/ surface with proper clamping/support complete as required. Make - Hevells/finolex/RR Kabel 205 Supplying and laying of 1 no PVC insulated and PVC sheathed/XLPE copper conductor, FRLS, multistrand, unarmoured power cable of 1.1 KV grade of size 3C* 1.5 Sqmm on cable tray etc.complete as required. Make - Hevells/finolex/RR Kabel
