Tender For Major Repair Works Under State Budget Head School In Govt. Ps. Garh Taiski Block Sikari - Dismantling brick tiles covering in terracing including stacking of serviceable material and disposal of unserviceable material within 50 meters lead. 3 Dismantling stone slab/ terrazo chip flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 meters lead. 4 Dismantling old plaster or skirting, raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 meter lead. 5 Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer-in-charge. 1: 3: 6 or richer mix. 6 Earth Work in excavation in foundation trench or drains including dressing of sides and ramming of bottoms, lift upto 1.5 m including tacking out the excavated soil and depositing and refilling of Jhiri with watering and remming and disposal surplus excavated soil as directed with in a lead of 50 m. all kind of soil. 7 P.C.C. IN FOUNDATION Providing and laying cement concrete including curing compaction etc. complete using stone aggregate 40mm nominal size (hand broken) in foundation plinth , excluding the cost of shuttering, using 1 cement:4 sand :8 aggregate mix. 8 STONE MASONARY FOR FOUNDATIONRandom Rubble Stone masonry for foundation and plinth in cement sand mortar 1:6 mix. 9 Brick masonry with bricks of class designation 75 in CM 1:6 in Super Structure 10 Half Brick Masonary in S.S. with bricks of class desiganation 75 in C.M 1:6 11 Random rubble dry stone kharanja under floor 150 mm thick. 12 Centering & shuttring with plywood of steel sheets including sturing proping etc. for suspended floors, roofs, landing staircase balconieds, girder, cantivlevers bands & bed plates anchor bocks skills etc. at grounds floor 13 RC.C. work in beams, suspended floors, foofs, griders having slope upto 15 landings, balconies, shelves chajjas, upto three floors including curing, compaction, finishing with rendering in cement in cement sand mortar 1:3 making good and joints exclu. cost of centering. shuttering and reinforcement with 1:1/5:3 (1cement:1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size at ground floor. 14 providing and fabricatin steel reinforcement for RCC work including cutting bending placing in position and binding complete including cost of binding wire in foundation faft footng step beams base of columms etc. upto plinth level hot rollet deformed (1st 1139) cold twisted bars. At Ground Floor. 15 PLASTER(INTERNALPlaster on new surface on wall in cement sand mortar 1:4 including ranking of joints etc. complete fine finished 12 mm thick 16 PLASTER(External)Plaster on new surface on wall in cement sand mortar 1:6 including ranking of joints etc. complete fine finished20 mm thick 17 Providing and laying in position cement concrete including curing compaction etc. complete in spcified grade excluding the cost of centering and shuttering all work upto plinth level 1:3:6(1 cement:3 Coarse sand :6 gradeed stone aggregate 20 mm nominal size). 18 kota stone slab flooring 25 mm thick over 20mm ( average ) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement: 4 Course sand ) for area 2001 to 5000 sq. Cm 19 Providing and fixing T -iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded with 15x3 mm lugs 10cm long embedded in cement concrete blocks 15x10x10 cm of 1 :3:6 (1 cement: 3 coarse sand: 6 graded stone aggregate 20 mm nominal size) or with wooden plugs and screws or rawl plugs and screws or with fixing clips or with bolts and nuts as require including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. 20 Providing and fixing MS sheet Dobule leaf door shtter in angle iron frame 35x35x5 mm suitability diagonally braced with 25x3 mm flat iron above and below lock rail of size 50x5 mm beading extra including. All fittings as per direction of enginneer in charge but excluding cost of chokhats m.s sheet 22 S.W.G. 21 Providing and fixing steel glazed doors windows and ventilator shutters of standarad rolled steel section joints mitred and welded with lugs 13x3mm,10cm long embeded in cement concrete block 15x10x10cm of 1:3:6 or with wooden plugs and screws or rawl plugs and screws with fixing clips or with bolts and nuts as required including providing and fixing of plain glass panes 4mm thick with coper glazing clips and special metal sash putty of approved make or metal beading with screws complete including priming coat of approved steel primer, excluding the cost of metal beading and other fittings expect necessary hings of pivots steel handles peg stay etc.as required for windows fixed 22 Supplying & fixing fixed wire Gauge of 14 mesh X 24 Gauge to the Metal frame of rolled section by metal beading 20X3mm with suitable screw at not exceeding 150mm distance. 23 Providing and fixing square bars or other flat welded to window ventilators etc. 24 Applying BIRLA/JK white cement based puttyover cement plastered surface to prepare the surface even and smooth complete 25 PANTING ON DOORS & WINDOWSPainting with Enemel paint of approved brand and manufacture in all shade on new steel work (2 or more coat ) 26 Finishing walls with Acrylic Smooth exterior paint of required shade including all scaffolding. New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including base coat of water proofing cement paint applied @ 2.20 kg/ 10 sqm ). 27 Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade including all scaffolding:Newwork(twoormorecoats)overandincludingscrappingandprimingcoatwithcement primer. 28 Providing & Fixing Ist quality standard White/Ivory Glazed Tiles ISI marked (IS : 13753) of size 300mmx200mm in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry mixed with pigment to match the shade of tile complete (excluding the cost of cement plaster ) Category -2nd,Bell, thar make etc. 29 Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard jointed with neat cement slurry mixed with pigment to match the shade of tiles includingrubbing and cleaning etc. complete on 20 mm thick bed of cement mortar 1:4 (1 cement : 4 coarse sand) 30 Total 31 Providing and fixing steel gate, grating , and grills made of angles, tees, square bars, flats,or black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide. 32 Providing and fixing Indian Type white glazed vitreous china 1st Quality W.C. Orissa Pan (I.S. 2556 Mark) with 100mm vitreous china P or S trap including utting and making good the wall and floor size 580x440mm. 33 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. (Concealed work including cutting chases and making good the walls etc.,)20mm nominal outer dia pipes 34 25 mm nominal outer dia pipes 35 P&F Bib cock (IS:8931 Mark),primer quality of approved makebib cock 15mm nominal bore. 36 P&F 15 mm dia connection pipe of approved quality/ make PVC Pipes with nuts 450mm. 37 P&F Flush Cock/Flush valve (IS :9758) for WC of approved make CP brass 25 mm nominal bore. 38 P & F Stop cock (IS:8931 Mark),Superior quality and of approved mark: Brass 400 gm. 15 mm nominal bore 39 P & F PVC Storage tank (IS 12701 marked indicating the BIS licence No.) of approved make with cover, 25mm dia 1M long G.I. Over flow pipe and 25 cm long wash out pipe with plug & socket including making connection etc complete of approved design. 500litre 40 P& F rigid PVC Pipe (IS 4985 Mark) Class 2nd /(4 kg /sqcm) approved quality / Make including joining the pipe with solvant cement rubber ring and lubricant 110 mm dia. 41 PVC Bend 110mm 42 pvc clip 43 Wiring of light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV gradeand 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694)inrecessed ISI marked MMS ( IS:9537 P - III ) virgin material PVC conduit & itsISI marked (IS:3419-1988) accessories, round tiles, 1.2 mm thickHot Dipped Galvanized Modular Box with earth terminal, 10A Modular switch,Modular face plate with grid plate, 3 pin ceiling rose / Holder /3 way connector, screws,making connections, testing etc. as required.For specification of copperConductor,Phenolic Laminated sheets & Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07 For additional technical parameters of product / work refer Annexure A attached with this BSR 44 Short point (up to 3 mtr.) 45 Medium point (up to 6 mtr) 46 Wiring of 3 pin 5 amp. light plug point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 KV grade and 1.5 sq. mm nominal size FR PVCinsulated unsheathed flexible copper earth conductor 1.1 KV grade (IS: 694) of approved make in surface/reces group -2 47 On board 48 S&F following sizes (dia.) of ISI marked ( IS:9537 P - II ) rigid steel conduit with wall thickness according to IS Specified along withISI marked (IS:14768 P-II 2003) accessories inrecessed using saddles, clamps, fasteners, pvc bushes, check nuts, as required includingcutting jhiris in the wall and making good the same as required. For additional technical parameters of product / work refer Annexure A attached with this BSR 49 25 mm dia 50 Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor as per PWD specification for electrical Works with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from99.90 % purity copper, class 5 stranding in acc. to IS:8130/IEC 60228 forlower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5,in existingsurface or recessed PVC/ MS conduit/casing capping making connections with Copper Lugs of suitable size, Ferrules,testing etc. as required. OEM Must have its own in house NABL lab setup for all testing facilities for wires. For additional technical parameters of product / work refer Annexure A attached with this BSR 51 2 x 1.5 sq. mm 52 2 x 2.5 sq. mm +1 x1.50sq.mm 53 Providing & Fixing of 240/415 V AC MCB with positive isolation of 10 kA breaking capacity (B/ C/D tripping characteristic as per type of load andsite requirement) 4 KV impulse withstand voltage, ISI marked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC 60947-2, low watt losses, trip free mechanisum , energy limiting ofclass 3 as per IEC,minimum phase termination capacity of 35sq.mm. , conductor line load reversibility , IP 20 contact protection and fitted inexisting distribution board/sheets, minimum electrical operation 20,000 upto 20 A rating and 10,000 upto 63 A, 5000 for 80 A & above ratingincluding making connections, testing etc. as required. OEM shall have submitNABL / CPRI / ERDA accrediated lab type test reports& All as per pre approved by Engineer in charge. For additional technical parameters of product / work refer Annexure A attached with this BSR 54 6 A to 32 A rating 55 Providing & Fixing of IP 20 boxmade outfrom 1.2mm thick CRCA sheet steel with depth of minimun 30 mm and finished with powder coating andsuitable for mounting LED tubeincludingside covers, holders , internal wiring to illuminate the single sided connection LED tube. ( Without tube).All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 56 Suitable for 4 LED Tube shape fixture for double rod 57 Providing & Laying P.V.C. / XLPE insulated & P.V.C. sheathed ArrmouredAluminiumcable confirming to IS:1554 P-I / IS :7098 P - I of 1.1 KV withH4- Grade electrolyticaluminium conductor confirming to IS 8130 of purity >99.6 %, round / flat strip armouring of cables, Inner / outer sheath confirming to IS:5831in existing RCC / Hume / Stoneware / PVC pipe/ open duct/cable trench / Cable tray(with cable tie) includingtesting etc. as required of following size. OEM must have its own in house NABL accrediated Laboratory for testing procedure as per IS:10810.For additional technical parameters of product / work refer Annexure A attached with this BSR 58 6.0 Sq. mm 4.00CORE 59 Providing & Fixing ofBEEStar rated copper wounded double ball bearing capacitor start, aluminium body & Metallicblade ceilingfanConforming to all the performance requirements laid down in IS 374:2019 including all amendments, as applicable ; & Carry BIS licensing (i.e. ISI marking) with down rod up to 80 cm with secondary support safety cable ( steel rope) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 60 1200 mm Sweep BEE 1 Star rated (service value >=4.0 to < 4.5 ) 61 Providing & Fixing of IS 11037:1984markednon modular socket size flush type 180 watt rotary minimum 5 step fan regulator with CM/L no. printed and made out from industrial grade Polycarbonate or fire resistant ABS material including making connection testing etc. as required.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 62 Providing & Fixing ofISI marked (IS:371) 6 amp surface type 3 pin ceiling rose with CM/L no. printed and made out from industrial grade Polycarbonate or fire resistant ABS material, brass terminal & captive screws including making connection testing etc. as required.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 63 Providing & Fixing of ISI marked (IS:1258) batten/angle lampholder with CM/L no. printed and made out from industrial grade Polycarbonate or fire resistant ABS material, brass terminal & captive screwsincluding making connection testing etc. as required.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 64 P & F 1.2 mm thickG. I. / M .S. Sheet boxes duly finished with two coats of red oxide and with earthing terminal of following sizes (nominal size) in recessed/surface as required.For additional technical parameters of product / work refer Annexure A attached with this BSR 65 P & F 1.2 mm thickG. I. / M .S. Sheet boxes duly finished with two coats of red oxide and with earthing terminal of following sizes (nominal size) in recessed/surface as required.For additional technical parameters of product / work refer Annexure A attached with this BSR 66 150mm x 150mm x 60mm
