Tender For Special Repairs To Certain Buildings And Provision Of New Works In C-1 Sector Under Ge (South) Ambala Cantt.; 1 Taking down wooden chowkats or frames with shutter (without taking off shutter from the frames), area not exceeding 1.5 Sqm each and removal from site including iron mongery hold fasts etc., complete all as specified. 2 Taking down wooden chowkats or frames with shutter (without taking off shutter from the frames), areaexceeding 1.5 Sqm and not exceeding 4.00 Sqm each, complete all as specified. 3 Supply & fixingof windows made of pre-painted steel (Base steel as per IS 513 of 0.58mm thick “D” Quality galvanized as per IS 277 with zinc of 120 GSM). Primer coated with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with 5-7 microns thick alkyd backer. Section for outer frame should be of 72x55mm, centre mullion should be of 72x50mm, section for fixed glass beading should be of 12x12mm and section for shutter should be of 48 x 25mm. Outer frame & mullion sections to have rebate for glazed shutters, fly mesh and 20 mm provision for guard bars/ grills fly mesh shutter section should be of 20x40mm. The sections are to be cut to length mitre joined with corner bracket. Centre mullions to be fixed with mullion cap. Elixir or equivalent stay, handles 2nos of heavy duty stain less steel pivot hinges shall be provided per shutter. The windows should be panelled with 4 mm thick plain float glass and S.S. Mesh for fly mesh shutter (304 grade). Rubber Gaskets are provided all around the glass. The above frames should be fixed to the concrete/masonry wall by means of self expanding screws. Including 10mm square guard bars with 6” (152.4mm) pitch, completeall as specified and directedby the Engr-in-Charge(Make:A2Z Infra Solutions/ Elixir Met form Pvt Ltd./ Urban Spaces) 4 Supplyand fixing3mm Sheet glass, ordinary quality, in squares n exc 0.5 sq. m eachand glazing with beads fixed with metal panel pins all as specified and directed 5 Supply and fixing of Factory made single extruded WPC (Wood Polymer Composite) solid door Frames/Chowkhat of size 125 x 65 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibbers and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with mitre joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardantNote: For WPC solid door frames, minus 5mm tolerance in Dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. 6 Supply and fixing ofFactory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 35mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibbers (wood powder/ ricehusk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant 7 Supply and fixing of providing30 mm thick factory made 100% Solid WPC (Wood polymer Composite) gauzed and skeleton Shutter of required size comprising of virgin PVC resin of K Value 57-60 ( Suspension Grade ),calcium Carbonate and natural fibbers ( Wood Powders/ rice husk/ wheat husk ) and Non toxic additives, made from Extrusion process WPC foam sheet Single Extruded ( Inner ) with having minimum density not less than 650 kg/cum manufactured and an ISO 9001 -2015 Certified Company, having good screw holding capacity ( Screw Withdrawal strength of 2000 N ( Face ) & 1100 N ( Edge ), Minimum Compressive of 50 N/mm2 Modulus of elasticity 850N/mm2and resistance of spread of flame of Class A category with Property of being Termite/ Borer Free. Water/ Moisture Proof and Fire Retardant. Fixing stainless Steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws incl Aluminium Jali and Stainless wire mesh as per required. complete all as specified and directed. Material test certificate and authentication should be compulsory provided by the manufacturing company 8 S&F factory made pressed steel frames for doors ofsize 125 x 60mm with one or more rebates including necessary fixing lugs, lock strike plate, hingesetc, complete as specified and directed . 9 Material & Labour 2nd class hardwood factory made 30mm thick glazed skelton shutters, open rebated and prepared to receive glass, gauge etc. divided into squares edges of framing, plain, chamfered or rounded, mitred fitted with cut and mitred beads for securing glass/gauge etc. with sizes of members of shutters as specified in SSR part-I section 8 clause 8.24(a) supply and fixed to chowkhats complete all as specified and directed by Engineer-in-Charge at site.Note : Manufacturers Test o be submitted before incorporation. complete as specified and directed 10 S&F factory fabricated flush shutters, 30mm thick, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed 11 S &F Steel window box type using ERW hollow P section comprising double frame for and including gauged and glazed Skelton shutter 30mm thick,jointed internally with flat iron 25x3mm complete including hinges, handle, tower bolts, stops, lugs etc. all as shown on drawing No. TD-219 (c) sheet 1/3 to 3/3 and TD-220 (c) sheet 1/3 to 3/3 as applicable complete. Make: Manufactured by Ram Fabricators Pvt Ltd Panchkula (Hr.) or M/S TEE PEE Enterprises Ludhiana (Pb.)Note: (i) For the purpose of measurement & payment double shutter with frame shall be considered as one unit. (ii) Unit rate quoted against this item shall also include the iron mongery, Guard bars etc (iii) Glazing, wire mesh & painting shall be measured & paid for separately. Note : Manufacturers Test o be submitted before incorporation. 12 S&F Galvanised mildsteel wire cloth 0.56 mmnominal dia of wire and average width of aperture 1.18mm as in gauze door /window/ventilators shutters complete all as specified and directed 13 M&L forpreparing new steel surfaces of any description , over 10 cm width or girth and applying two coats of synthetic enamel paint(first quality) over a coat of primer complete all as specified and directed 14 M/L two coat of synthetic enamel paint on new steel surfaces of any description, over 10cm in width or girth, not otherwise described incl preparation of surfaces all as specified 15 M&L for two coat of synthetic enamel paint to new wooden surfaces of any description, not otherwise described, over a coat of pink primer, over 10cm width or girth incl preparation of surfaces all as specified 16 M & L for one coat of synthetic enamel paint inclpreparingold painted steel surfaces of any description not otherwise described over 10 cm width orgirthcomplete all as specified and directed. 17 S&F 150mm long extruded aluminium alloy handles, fabricated type, anodised. 18 S &F Aluminium alloy, anodised, sliding door bolt 300mm longwith hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and 19 S&F 100mm long aluminium anodised barrel tower bolts of extruded section. 20 S&F 200mm long aluminium anodised barrel tower bolts of extruded section .complete as specified and directed . 21 S & F 300mm, ordinary rat tail rod pattern springs including roller and roller plate completeif fixed to steel/ concrete chowkats with flat iron 40x3 mm size 75 cm long with necessary bolts, etc. complete as in repairs 22 S&F aluminium powder coated curtain rod of 20mm dia decorative type all as specified and directed as in repairs 23 S&F Brackets Aluminium anodised for curtain rod20mm dia all as specified and directed 24 M&L PCC in roof kerbs of mud stops, rounded or chamfered on edges type B1 (1:2:4) using 20 mm graded aggregate complete all as specified and directed 25 Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises. 26 Material & Labour for Non - skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and includingcement screed bed 15mm thick in screed bed (1:4) base, complete all as specified. 27 Material & Labour for Vitrified colouredtiles 7 to 8 mm thick dark shade (square/ rectangular) area of each tile exceeding n. exc0.36 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and includingcement screed bed 15mm thick in screed bed (1:4) base, complete all as specified. 28 M&L for coloured designed 600x300x7mm thick glazed ceramic tiles on vertical surfaces such as skirting dado and risers to step etc including backing coat of 10mm thick rendering in CM ( 1:3) set and jointed in neat cement slurry and pointed in white or coloured cement to match completed as specified and directed. 29 M&L forcoloured glazed ceramic tiles (300x 450x 7mmthick)in vertical surfacesand jointed in neat cement slurry and pointed in white or coloured cement to match including rendering 10mm thick in cement plaster 1:4 complete all as specified and as directed. 30 Demolition of brick work built in cement mortar or cement lime mortar including all pillars, quoins etc., complete all as specified. 31 Material & Labour for Brick work with sub class ‘B’ bricks , straight or curved on plain exceeding 6 metre mean radius in cement mortar (1:6), complete all as specified., complete all as specified. 32 Supply & fixed ( in repair)CP bib tap screwed down high pressure, long body, cast copper alloy, chromium plated`with crutch or butterfly handles screwed down suitable for 15mm bore pipe or union, complete all as specified. (Note : Weight of bib tap shall not be less than 0.575 Kg). 33 Dismantling of ceiling boards (fibre, pulp, insulation, etc.) or insulation boards /slabs/ blankets, any thickness, including cover fillets, as in false ceiling etc complete all as specified. 34 Supply and fixing of semi perforated false ceiling 12 mm thick with micro tegular edged at all height with GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of size 595 x 595 mm of approved texture, design and pattern having moisture content less than 2%, humidity resistance of 99%, NRC 0.60 to 0.85 as per IS 8225-1987, non combustible as per BS 475 (Part-4) 1970 and light code description unit code No 429 Sub Head 26. New Technologies and materials reflectance of 85% minimum to be laid in true horizontal level suspended on interlocking metal T -grid of hot dipped galvanised iron section of 0.33 mm thick ( galvanised @ 120 gms/ sqmincluding both sides) comprising of main T- runners of size 15x 32mm of length 3000mm, crossT of size 15 x32 mm of length 1200mmand secondary intermediate cross T of size 15 x 32 mm of length 600 mm to from grid module of size 600 x 600 mm, suspended form ceiling using galvanised mild steel items (Galvanised @ 80 gm/sqm) i.e. 50 mm long, 8mm outer diameter M-6 dash fastners, 6mm dia fully threaded hanger rod upto 1000mm length and L shape level adjuster of size 85 x 25 x 2mm.galvanised iron perimeter wall angle of size 24 x 24 x 0.4 mm of length 3000 mm to be fixed on perimeter wall / partition with the help of plastic rawl plugs at 450 mm centre to centre and 40 mm long dry wall SS screws. 35 M&L for PVC false ceiling consisting of 600mmX600mm, 5mm(+ 0.25) thick plain embossed PVC sheet of density 600 Kg/Cum manufactured by an ISO-9001-2015 certified company, used as panel insert in a frame work made using anodised aluminium T-section of sizes 1 x1 (25mmX25mm,1mm thick) in square pattern of grid sizes of 2X2(600mmX600mm). The aluminium framework is supported from the ceiling with the help of J hook and G.I. wire / 4mm MS rods of required sizes to maintain proper level etc. The aluminium frame work is supported on the side wall with the use of aluminium L- Section of size 1X1 (25mmX25mm, 1mm thick) Angles etc. Complete as per direction of Engineer-In- Charge, Manufacturer, specification and drawing. 36 Supply & fixing factory made PVC hollow door frame of size 50 mm x 47 mm with wall thickness of 5 mm made out of extended 5 mm rigid PVC foam sheet cut at corner and jointed with 02 Nos., 150 mm long brackets of size 15 mm x 15 mm mild steel square tubes 19 gauge including vertical door profiles reinforced with 19 mm x 19 mm steel square tube of 19 gauge (EPDM) rubber gasket weather seal provided through out the frame and fixed to wall with 65/100 mm long mild steel screws through the frame by using PVC fasteners (minimum of 04 Nos. of screws to be provided for each vertical number & minimum 02 Nos. for horizontal member), complete all as specified. 37 Supply & fixed factory made 30 mm PVC rigid foam panel door shutter made from mild steel tubular frame of size 19 mm x 19 mm for stiles and 15 mm x 15 mm for top & bottom rails and covered with 5 mm thick head moulded PVC channel having width of 50 mm to form stiles & PVC street of width 75 mm to form rock rail, bottom rail & top rail or either side having panels inserted with 5 mm thick PVC sheet sealed with solvent cement adhesive to the stiles and rails with 5 mm x 25 mm PVC sheet beading on either side including three Nos. aluminium hinges for each door complete all as per manufacturer instructionscomplete all as specified. 38 Taking down cement plaster on brick wall/concrete surfaces etc including racking out joints hacking for key scrubbing down with water etc of any thickness including dado any descriptionall as specified. 39 M&L for 15 mm thick rendering on faces of brick or concrete surfaces in CM 1:4. finishing the surface even and smooth without using extra cement complete all as specified. 40 M&L for rendering 15mm thick in (1:6) CM on fair faces of brick work or concrete surfaces of walls. Fair andeven complete all as specified and directed. 41 Material andLabour for preparation of exposed brick wall surface by cleaning the surface wire brush to remove all dirt/loose materials from the bricks and from the joints between the bricks. Prepared surface should be then washed with diluted HCL acid (dilution ratio of 1:50) for three times in a day for two days. After acid wash surface should be allowed to be air dried for one day. NOTE : - Further treatment over the surface so achieved will be carried out only after approved of the same by GE. 42 Material and labour for efflorescence treatment to unplastered wall surface comprising of the following specification complete all as specified and as directed.(a) Prime the prepared surface with one of the following product mixed with cement in 1:1 ratio as bonding agent : -(i) Pidicrete URP of M/S Pidilite. (ii) Sika Latex of M/S Sika.(iii) Nitobond SBR Latex of M/S FOSROC.(b) Immediately after priming the surface PMM (Polymer Modified Mortar) to be applied “BY HAND” while the prime is tacky. PMM should be prepared by mixing one of the following compounds in Cement Mortar 1:3 as per manufacturer’s instructions: -(i) Pidicrete URP of M/S Pidilite.(ii) Sika Latex of M/S Sika.(iii) Nitobond SBR Latex of M/S FOSROC.(c) PMM surface should be allowed to dry for one day. After that it should painted with two coats of one of the following compound mixed with cement only in ratio of 1 (selected compound) : 1:5 (Cement) : - (i) Pidicrete URP of M/S Pidilite.(ii) Sika Latex of M/S Sika. (iii) Nitobond SBR Latex of M/S FOSROC.(d) Now apply two coats of one of the following compound over the surface. These compounds are to be used as per manufacturer’s instructions: -(i) Pidifin 2K of M/S Pidilite (ii) Brush Coat of M/S Sika.(iii) Brush Bond of M/S FOSROC. (ii) Every stage of work will be approved by GE, then only next layer will be executed by contractor.NOTES : (a) The efflorescence treatment shall be carried out by the manufacturer or his authorised representative only. (B) The efflorescence treatment shall be carried out after taking down existing plaster redoing external/internal plaster under respective Items. (b) Make: Pidilite, DR Fixit or Equivalent make as approved by GE. 43 M & L forrough cast plaster on exterior walls in two layers, under layer 10mm cement plaster 1:4 (1 cement: 4 coarse sand ) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 Kg of cement per square metre, top layer 15mm Rough cast plaster with sand gravel as specified as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the surface complete all as specified 44 Mel for two coats of cement base paint over a coat of alkali resistant primerof new surfaces of walls and incl preparationcomplete all as specified. 45 M & L for preparation new plastered surfaces of wall and applying two coats of oil bound distemper over a coat of primer applying with rolleretc complete all as specified and directed. 46 Material & Labour for two coats of oil bound distemper over a coat of primer incl preparation of new plastered surfaces of walls and applying 3mm thick (Minimum) white cement based wall care putty in two coats, finished even and smootcomplete all as specified. 47 Material andlabour fortwo coats of exterior emulsion paint, on new surface on walls, chajjas etc over a coat of primer of same manufacturers of as emulsion including necessary scaffoldings upto 12 mtr or more height, complete all as specified and directed. 48 Taking up or down steel tubing and connections for 15mm dia including cleaning for refixing or removal to store complete all as specified and directed by Engr-in-charge. 49 Supply & fixing Steel water tubing of 15 mm bore, medium grade galvanized, ISI marked with all fittings laid in floor with wall , complete all as specifiedand directed . 50 Taking up or down steel tubing and connections for 20mm dia including cleaning for refixing or removal to store complete all as specified and directed by Engr-in-charge. 51 Supply & fixing Steel water tubing of 20 mm bore, medium grade galvanized, ISI marked with all fittings laid in floor with wall , complete all as specifiedand directed . 52 Material & Labour for cutting chases for concealed water tubing and making good, (cutting not exceeding 10 cm girth) (brick walls) in cement mortar (1:3), complete all as specified. 53 S&F PVC (SWR) Nahani /Floor trap, 75 mm dia of out let, plain with grating including jointing to waste pipe with solvent cement. 54 Material & Labour for PVC water storage tank 500 Litre capacity HDPE triple layer ISI marked fixed & hoisted in position on staging or roof complete with locking arrangement, over flow pipe, air lock pipe, Ball valves, high pressure of PTMT with, ISI marked complete all as specified.including dismantling of old tanks ofany description complete all as specified. 55 Supply & fixed (in repair) 15mm fancy type, chromium plated, angle cock, cast copper alloy, screwed down high pressure with crutch or butterfly handle, heavy with adjustable wall flange, complete all as specified. 56 Supply & fixed (in repair) stop cock, fancy type, chromium plated, long sank and cup (concealed type) screwed down high pressure with crutch or butterfly handle screwed both ends suitable for 15mm bore pipe, complete all as specified.(Note : Weight of stop cock shall not be less than 0.575 Kg)(Note : Weight of stop cock shall not be less than 0.575 Kg) 57 Supply and Fixed (in repair) for vitreous China squatting pan of Orrisa pattern size 580 x 440mm white (Ist quality) with ‘P’ or ’S’ trap, front or back inlet and foot rests of anypattern complete including provision of lime concrete bed and connection to flush pipe excluding flushing cistern, flush pipe and bracket and making good the disturbed area complete all as specified. 58 Supply & fixed (in repair) vitreous China wash hand basin white flat back of size 550x440mm including CI brackets and 15mm chromium plated pillar tap, PVC connection 450 mm long having PTMT nuts and chromium plated waste coupling and making good to disturbed portion including32 mm dia PVC waste pipe etc., complete all as specified. 59 S & F Vitreous China urinal half stall back or corner type complete incl providing and fixing plugs bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement fixing automatic flushing cistern with brackets flush pipe, grating and union for discharge pipe complete all as specified and directed by Engr-in-Charge 60 Supply & fixed in repair 10 litre capacity flush polypropylene cistern, ISI marked, white at low level complete with PVC bend/flush pipe and making all connection including taking down existing high/low level cistern with all connections and making good the disturbed surfaces in cement mortar (1:3) to match with the existing surface, complete all as specified. 61 S&F, in repairs, 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6 mm thick AC bldg Board or commercial plywood, fixedwith aluminium angled frame and two CP MS hanging arrangements all complete. 62 S&Fin repair towel rail Cat No BA -50of Prayag polymers Pvt Ltd or equivalent complete as specified and directed by Engr in charge. 63 S&F in repair Soap dish, any type, fixed to plugs with chromium plate brass screws complete as specified and directed by Engr in charge. 64 S&F in repair cast copper alloy, chromium plated shower rose incl long pipecomplete as specified and directed. 65 S&F in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12mm wide and chromium plated brakects guard and railing 60cm long fixed in repairs complete as specified and directed by Engr in charge. 66 Demolition and breaking up drain pipes100/75 mm (Salt glazed ware, AC or Reinforced concrete) set in cement mortar complete all as specified. 67 S&F in repairPVC(SWR) 110 mm pipe single socket in any length with rubber ring joints fixed to wall or infloors complete as specified and directed by Engr in charge. 68 S&F in repair PVC (SWR) bends 110 mm bore complete all as specified. 69 S&F in repair PVC (SWR) 75 mm pipe single socket in any length with rubber ring joints fixed to wall or in floor complete as specified and directed by Engr in charge. 70 S &F in repair PVC (SWR) bends of 75mm radius 71 S &F in repair 75mm PVC (SWR) junction single,(Single T) equal or unequal provided with access door 72 S & F in repair PVC (SWR) vent cowl of 75mm dia 73 S& F in repair PVC (SWR) junction single, (Single T) equal or unequal of 110mm dia with access door all as specified and directed 74 Supply and fixingBall brass valves, of 20mm bore high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed as in repairs 75 M & L for Mild steel TMT bars 8 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hookingends and binding with and including mild steel wire(annealed) not less than 0.9mm dia or securing with clips complete all s specified and directed. 76 M & LReinforcement 10mm dia and over TMT bars including cutting, bending and binding with 0.9mm dia binding wire complete all as specified. 77 Material and labour for precast cement concrete type B-1 1:2:4 (using 20mm graded mechanically crushed stone aggregate )as in cover slab for mabhole , shelves etc set in cement mortar (1:4) and finished cement concrete surface even and fair without using extra cement complete all as specified and directed 78 Supply & fixing in repair mild steel 25 mm tubular rod in plumet rod, 1.6mm fancy type includinggolden colour brackets end caps and wall to wall socketetc complete all as specified and as directed by engineer-in-charge. 79 S & F 300mm, ordinary rat tail rod pattern springs including roller and roller plate completeif fixed to steel/ concrete chowkats with flat iron 40x3 mm size 75 cm long with necessary bolts, etc. complete as in repairs 80 Demolition of cement concretein ground floors and pavings n exc 15 cm thickness (below or above ground level)complete as all specified and directed. 81 Material and labour for 100 mm thick cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate as in sub base complete all as specified and directed 82 M& L for PCC (1:4:8) type D2 with 40 mm graded stone aggregate lean concrete complete all as specified and directed.. 83 M& L for PCC (1:2:4) type B2 with 40 mm graded stone aggregate as in foundation filling cement concrete in surface channel and drains all as specified. 84 M & L for Sand filling/ cushioning in floors including levelling, watering and consolidation, complete all as specified and directed 85 S&F Chequered tiles non skid ( coloured) good grip series of size 300x 300 mm x 20-25 mm thick, set ,jointed and pointed in neat cement slurry laid over and including 20 mm thick average thickness cement mortar 1:4bed, including dismantling of existing tiles complete all as specified and directed. 86 Material and labour forPCC in 1:3:6 type C-1 (using 20mm graded mechanically crushed stone aggregate) 50 mm thick as in plinth protection, path, laid in alternate bays etc. Finished even and smooth without using extra cement and joints filled with bitumen and sand mixture applied hot complete all as specified and directed. 87 Machine pressed precast concrete interlocking paver block any shape and size conforming to is 15658-2006 of 60 mm thickness M-35 grade with grey cement and pigment finished with coloured rubber finish on top finished over and including sand cushion 50 mm thick complete all as specified and directed. 88 M&L, for sand cushioning layer for laying PCCinterlocking paver block complete all as specified. 89 M&L for Machine pressed precast concrete inter locking paver blocks of any shape andsize conforming to IS 15658- 2006of 60 mm thick M-35 grade with grey cement andpigment complete all as specified and directed. 90 Surface excavation n.exc 30cm deep and averaging 15cm deep and getting out in soft / loose soil. 91 M&L for hard core(broken stone boulders) of gauge n.exc 63mm,deposited spread and levelled in layer n exc 15cm thick watered and rammed to a true surface. 92 Excavating in trenches not exc 1.5 mtr wideand depth exc1.5 mtr but n.exc 1.5 min depth, and getting out insoft/ loose soil. 93 Removing excavated soil n.exc. 50 mtr and depositing where directed at a level not exc 1.5 m above the starting point in soil. 94 Removing excavated material, exceeding 1.5 km but not exceeding 5 km and depositing where directed outside MD land completed all as specified and directed. 95 Excavation in post holes (or similar holes) each n exc 0.5 cum, getting out, returning, filling in complete all as specified. 96 M& L for PCC (1:2:4) type B2 with 40 mm graded aggregate as in post holes, any thickness, size or shape including pilasters, buttresses columns, pillars, boundary and posts pillars etc all as specified and directed. 97 S&F structural rolled mild steel Fe 410-00 (Gde E-250) as in rafters purlins where connectedto common rafters and running railfixed with angle cleats or other connecting plates etc completed all as specified and directed. . 98 Supply andfixing (in repair) partly glazed aluminium alloy anodized (powder-coated) partition (Area of each panel not exceeding 1.5 Sqm each)with frame of size not less than 100 mm x 44.4 mm x 2 mmincluding packing withrubber gasket, standardaluminium beading around both sides including 6mm thick plain coloured Bakelite sheet or acrylic boards, prelaminated both side with one side decorative choice lamination for fixing in bottom panel of aluminium partition as required complete all as specified and directed.Notes :-1.Glass pane shall be measured and paid separately.2. Manufacturers of section : M/S Indian Aluminium Co. Ltd., UCO Bldg, New Delhi. M/S Jindal Aluminium Pvt. Ltd. M/S Hindalco Pvt. Ltd. or equivalent make as specified in appendix B. 99 S & F in repair 5mm thick hollow interlocking wall panelling of width 250mm for wall panelling for fixing on to wall with screws and solvent alonghwith corner and u channel beading of colour choice including dismantling old beading/panelling all as specified and directed Note : Rate will be inclusive ofany electrical fitting /boardeffected and refixing the same after rectification 100 Dismantling Asbestos Cement (Corrugated, Semi corrugated etc.) sheets in roof coverings. 101 Dismantling wrought iron or mild steel work of any description specifically provided for gates, staircase railings, framed truss etc complete all as specified and directed. 102 Dismantling timber scantling 40 sq.cm in section complete all specified and as directed 103 S&F steel windows or ventilators, fixed type, with glazing bars complete all as specified and directed. 104 M&L structural steel mild steel Roof Trusses (framed) , trussed , rafter, purlins, crane gantries, rails and fastenings and heavy bracket framing ( Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. FE 410-w(GdeE-250) quality A complete as all specified and directed by EIC 105 S & F of rolled mild steel as in bands, straps, winds, ties, angle cleats and similar small articles etc conforming to Fe-290 Gde including dismantling existing mild steel complete all as specified and as directed. 106 S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 mpa as in roof covering/cladding to wall, fixed with self tapping screws or J type hooks including rubber washer, complete all as specified and directed by Engineer in charge. 107 S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 mpa as in roof covering/cladding to wall, fixed with self tapping screws or J type hooks including rubber washer, complete all as specified and directed by Engineer in charge. 108 M & L preparation of new steel surfaces of any description over 10cm width or girth (guide for roller) and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. 109 M & L for PCC 1:3:6 type C1 (using 20 mm graded stone aggregate) as in surface channels and drains complete all as specified and directed. 110 Extra over for forming fair finished to drains or channels n exc 30 cminnergirth in cement concrete using extra cement including forms moulds, metered/ stopped ends complete all as specified. 111 Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick with soft/loose soil. 112 Dismantling/taking down carefully aluminium/ copper point wiring (light, fan, socket or power) complete, including fixtures and fittings such as switches, ceiling roses, pendants, regulators , sockets, light fittings etc., removing materials to stores for keeping in safe custody for taking credit and making good the disturbed surfaces of walls, ceilings etc. complete all as specified and directed. 113 Taking down Ceiling fan any size or any type and deposited to MES store yard complete all as specified and directed. 114 Taking down old unserviceable underground cable/Service wireof any size/type complete all as specified and directed 115 Material and labour for concealed point wiring using approved colour coding as per IS, with multi stranded copper conductor 1.5 sqmm (Nominal area), single core, FRLSH (FIRE Retardant Low Smoke and low Halogen), PVC insulated and unsheathed stranded cable drawn through and including non metallic, medium grade PVC concealed conduit not less than 20mm dia and its fittings including all tees, bell mouth pieces and fixing accessories such as couplers, saddlers, pipe hooks etc, PVC junction boxes ISI marked with GI metal flushboxes made out of 1.2mm thick of any module from 2 to 18module confirming to IS-5139(pt-I) of 1969 and IS:14772-2000 with earth dolly coated with two coats of anti corrosive paintincluding modular cover plates with frame i.e. inner and outer plate extended upto 25 mm over metal flush boxes for housing the modular switches, socket outlets, fan regulators etc with brass screws and brass washers and making good the disturbedsurfaces as per existing for one light / fan / Bell point controlled by one switch including 1.5 sqmm single core PVC insulated and unsheathed FRLSH (FIRE Retardant Low Smoke and low Halogen) copper cable, 1100 volt grade with multi stranded copper conductor green colour as earth continuity conductor upto common earth and connecting to common earth dollywith suitable size of lugs for one light point/ fan point/bell point controlled by one switch complete all as specified and as directed.NOTES:- 1. Switch, socket and fan regulators to be measured and paid for separately.2. All chases will be cut by chase cutter only. 116 Description all as per item No 115 here in before but for socket out let point 5 Amps on same board complete all as specified and directed. 117 Description all as per item No 115 here in before but for socket out let point 5 Amps on independentboard complete all as specified and directed. 118 Description all as per srl item No 115 above but point wiring for one socket out let 16/6 Amps (independent) controlled by one switchwith using 2.5 Sq mm (nominal area) stranded copper conductor complete all as specified and directed. 119 Supply and fix modular switches, one way,6 amps one module, 230V, 50 Hz supply, complete all as specified and directed. 120 Supply and fix modularswitches, oneway, 16Amps, one module, 230 volt , AC supply, complete all as specified and directed. 121 Supply and fixmodular socket outlet 6 amps, 2/3 pin combined 2 module, 230 volt, complete all as specified and directed. 122 Supply and fix modular socket outlet 6/16 amps,3 pin, 2 module, complete all as specified and directed. 123 Supply and fix fan regulator step type one module / 2 module, 100w 230 Volts, 50 Hz, AC complete all as specified and directed. 124 Supply and fix modular switches, bell push,6 amps one module, 230V, 50 Hz supply, complete all as specified and directed. 125 Supply and fix modular blanking plate 1 module complete all as specified and directed. 126 Supply and fix ceiling rose surface bakelite 65x50mm, 3 terminal complete all as specified. 127 Supply and fix door bell electric ,ding dong /musical type, single phase 230 volts, ISI marked complete all as specified. 128 Supply only lamp holder, PVC/polycarbonate type with back plate suitable for batten fittings, complete all as specified and as directed. 129 Supply and fix sheet metal enclosure SP with two pin and earth plug and socket including metal clad topwith one single pole MCB 32 Amp complete all as specified and directed. 130 Supply and fixing of LED light fitting 1x20W (lumen efficacy of >100 lm/W) , 220V, AC with aluminium housing with batten type with driver , holder including 20W LED tube light for connecting up with three core flexible copper conductor cable of suitable size from celling rose to connector complete all as specified and directed. 131 Supply and fix batten type withsurface mounted LED tube light fitting with high efficient diffuser mirror light, aluminiumhousingin CRCA body suitable and including 10 watt LED tube rod high efficient, AC 220-240 volts, 50 Hz and connecting with copper conductor flexible cable of size 0.50 Sqmm from ceiling rose to connector of the light including disconnecting and taking down old existing light fitting of any description and in any position complete all as specified and directed. 132 Supply and fixbulk head light fitting, 10 watt, energy efficient withlamp 10 watt with provision of 2/3 core PVC copper conductor cable 0.5 Sqmm size from ceiling rose to light fitting completeincluding disconnecting and taking down old existing light fitting of any descriptioncomplete all as specified and directed. 133 Supply and fixing LED surface mounted bulk head luminaries 8-10W with min 800 lumen, industrial model IP65, aluminium housing , surgeprotection including driver & LEDetc complete with all accessories connecting with copper conductorflexible cable from celling rose to connector of the light complete all as specified and directed. 134 Supply and fixbracket for security light made up of 25/40/50mm dia suitable for security light, 0.6 metre long GI pipe,light grade, 120 degree bent to required length, fixed to wall with two clamps made of 20 x 3 mm mild steel flat minimum 15cm long, 4 nos 8mm dia bolts with nuts complete all as specified and directed. 135 Supply and fix LED security light luminaire 30 watt , pressure die cast aluminium housing, toughened heat resistant glass, IP66 protection, better optics for uniform distribution with multiple LEDshaving optical grade polycarbonate lens with all accessories internally pre wired and including connecting up with Two core 1.5 sq mmcopper conductor cable from connector to ceiling rose to connection of light including disconnecting and taking down oldunserviceable security light fitting of any description and in any positioncomplete all as specified and directed. 136 Material and labour for sub main wiring with two single core FRLSH PVCinsulatedunsheathed copper conductor cable 6sqmm drawnin and including rigid non metallic PVC medium grade 25 mm dia New concealed conduit with accessories onwall or ceiling withone additional PVC insulated , strandedcopper conductor FRLSHof 6 sqmm, green colourfor earthcontinuity conductor including taking down old unserviceable sub main wiringand making good the disturbed surface complete all as specified and directed. NOTE:-3 run of 6.0 sqmmcable with concealed conduct shall be measured as 1 unit. 137 Material and labour for sub main wiring with two single core FRLSH PVCinsulatedunsheathed copper conductor cable 4 sqmm drawnin and including rigid non metallic PVC medium grade 25 mm dia New concealed conduit with accessories onwall or ceiling withone additional PVC insulated , strandedcopper conductor FRLSHof 4 sqmm, green colourfor earthcontinuity conductor including taking down old unserviceable sub main wiringand making good the disturbed surface complete all as specified and directed. NOTE:- 3 run of 4.0 sqmmcable with concealed conduct shall be measured as 1 unit. 138 Material and labour for sub main wiring with two single core FRLSH PVCinsulatedunsheathed copper conductor cable 2.5 sqmm drawnin and including rigid non metallic PVC medium grade 20 mm dia New concealed conduit with accessories onwall or ceiling withone additional PVC insulated , strandedcopper conductor FRLSHof 2.5 sqmm, green colourfor earthcontinuity conductor including taking down old unserviceable sub main wiringand making good the disturbed surface complete all as specified and directed. NOTE: - 3 run of 2.50 sqmmcable with concealed conduct shall be measured as 1 unit. 139 M&L for cutting existing steel tubing for alterations or additions (Each cut measured) screwing existing steel tubing of any size for alterations or additions (or lengthening screw on pipe to form connector) complete all as specified and directed. 140 S&F of single pole and neutral enclosure with2 pin plug and socket with one MCB 20 Amps,10KA B curve complete all as specified and directed. 141 Supply and fixing in repair sheet metal enclosures vertical distribution board VTPN,(MCCB DB) 4 ways, double door , 415 volts with 200 amps rated bus bar IP 54 protection, with shrouded neutral bar and insulated bus bar and earth link, with and includingMCCB 4 pole thermal release type ,125AMPS ,25 KAas incomer and MCB sas out going complete with making suitable size of MS cabinet 1.2 mm thick dully grouted on the wall (flush) with opening arrangement including making connections with suitable size of lugs and making good the disturbed surface matching with existing surface complete all as specified and directed. 142 Supply , installation, testingofSPN distribution board 12 way, double door , IP 43 , as per IS 8623including 200 amps fully insulated copper bus bar, insulated neutral bar, earth bar, door earthing, reversible doors, PAN assembly for easy installation and also incoming and outgoing connections with suitable size of lugs/thimbles. 143 Supply and fixing in repairSPN distribution board 8 way, double door, IP 43, as per IS 8623including 200 Amps fully insulated copper bus bar, insulated neutral bar, earth bar, door earthing, reversible doors, PAN assembly for easy installation and also incoming and outgoing connections with suitable size of lugs/thimbles /gland/gaskets complete all as specified and directed. 144 Supply and fixing in repair MCB single pole, 240 volts, 50Hz , breaking capacity 10KA, B curve 6 to 32 Amps, ISIcomplete all as specified and directed. 145 Supply and fixing of MCB single pole, 240 volts, 50Hz , breaking capacity 10KA, B curve 6 to 32 Amps, ISIcomplete all as specified and directed. 146 Supply and fixing in repair MCB single pole, 240 volts, 50Hz , breaking capacity 10KA, B curve 40 to 63 Amps, ISI marked complete all as specified and directed. 147 Supply and fixing in repair MCB single pole and neutral 240 volts, 40 to 63 Amps,10KA, 50 Hz,B Series complete all as specified and directed. 148 Supply and fixing recess/ surface mounted LED flat panel 2 x 2 with high efficient LEDs and glare free full decorative light fitting, 36 watt, energy efficient provided withincluding LED36 watt withprovision of 2/3 core PVC copper conductor cable 1.5 Sqmm size to light fitting and completeincluding disconnecting and taking down existing light fitting and removal complete all as specified and directed. 149 Material & labour for earthing with Galvanised Steel earth plate electrode 60cmx 60cm x 6.0 mm thick buried directly in ground vertically at a depth not less than 2.25metre below normal ground level with top edge of earth plate at a depth not less than 1.5 metre below normal ground level, earth plate surrounded from all sides by 15cm thick packed layer ofcharcoal dust and common salt filling in alternate layers and electrode connections by usingGalvanised Iron wire 4mmas earthing lead(upto terminal point) by means ofbolts, nuts, check nuts and washers made of galvanised iron and thimbles and protected by light grade 15 mm diaGI pipe connected to main switch board or main control board and GI pipe medium grade 20mm bore for watering and including funnel , wire mesh , RCC pit cover and PCC chamber pit with PCC (1:3:6)type C-2 using 40mm graded stone aggregate, including excavation and earth work in any type ofsoil , returning , filling in approved soil and disposal of surplus soil to a distance not exceeding 50m all as specified and shown in electrical plate No 3 ofSSR 2009 (Part-I) including dismantling/taking out of old unserviceable earthing complete all as specified and directed. NOTE : - The unit rates also include for necessary earth work, GI protection pipe, funnel, wire mesh and CI cover. 150 Supply and fixing GI tubing 50 mm bore, light grade with all fittings and fixed complete to walls and ceilings or laid in floors, complete all as specified and directed. 151 Supply and fixing of LED lamp 9 watt B-22 base complete including taking down old existing lamp any type complete all as specified and directed. 152 Supply and laying of LT underground service cable, XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured electric power 1100 volts grade with stranded aluminium conductor of size 10 Sqmm 2 core complete with suitable size of PVC concealed/surface conduit alongwith necessary fixing accessories complete all as specified and directed. 153 Re-fixing Ceiling fan of any size/makeafter minor repair,servicing and greasing including painting complete all as specified and directed 154 Supply and fix heavy duty ISI marked energy efficient exhaust fan 300mm sweep, 230V,AC, 1400 RPM, Air delivery more then 1700 CMH with metalic body, four blades, double ball bearing, legs, frame and louvers, connecting up including provision of three core flexible copper wire of size 23/0.0076 from ceiling rose to exhaust fan, making hole on wall grouting bolts nuts washers, including commissioning and testing after installation complete all as specified and as directed . 155 Supply, installation and testing of storage type heater (Geyser) of 25 Litres Capacity, vertical type to sustain high pressure upto 8 bars with fixing bolts / fastener, necessary PCC/cement work and making good the disturbed surfaces to match with existing surface giving electric and water connection, with temperature resistant SS braided pipe suitable to sustain pressure up to 8 barnot less than 60 Cm long suitable forincoming / out goingwater connectionsand testing after installation to entire satisfaction of the Engineer-in-Charge complete with following specifications : - (a) 5 Star rated (Vertical type) Necessary BEE certificate from OEM shall be produced by the contractor at the time of sample approval. (b) Metal Body, (c) Glass line coated tank (Ferro-glass technology) / Polymer coated.(d) Incoloy glass coated heating element. (e) Adjustable thermostat. (f) Temperature indicator dial/digital type.(g) Multiple Heating Option. (h) Multiple Functional Safety Valve. (j) Thermal Cut-out Capillary Type. (k) In built protection for overheating/over pressure.(l)In-built RCD rated 16 A / 250 V AC 50 Hz / 3000 W IP40 protection with 30 mA Residual Current Trip Levels Less than40 m/s trip response time for ground fault and grounded neutral trip. NOTE : - Warranty certificate to be produced by the contractor from OEM for the following components before processing the bill.(a) For product - 02 Years Warranty (b) For metal tank 07 years Warranty. 156 M&L Stop valves 15 mm bore , cast copper, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe complete all as specified and directed. 157 M&L Bib taps 15mm bore , chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe complete all as specified and as directed. 158 M&L GI tubes 15mm bore, medium gradegalvanised, with all fitting and fixed complete to walls and ceilings or laid in floors. 159 Note:-Amount of credit ofRs. 1,71,719.00 for retrieved materials is mentioned in Schedule of Credit Page No. 17 & 18 of tender documents in pdf form which will be deducted offline while acceptance of tender.
