Tender For Emerging Nature Misc. Civil Maintenance Work In Bsnl Technical And Administrative Offices/ Buildings At Oa-Mathura, Ba-Agra During The Year 2025-26 Ph-I; 1 Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. 2 Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) 3 Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix) 4 Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.. 5 In cement mortar 6 Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead: 7 Of area 3 sq. metres and below 8 Dismantling G.I. pipes (external work) including excavation and refilling trenches after taking out the pipes, manually/ by mechanical means including stacking of pipes within 50 metres lead as per direction of Engineer-in-charge : 9 15 mm to 40 mm nominal bore 10 Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. 11 Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceable material with in 50 meters lead as directed by Engineer-in-charge. 12 Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. 13 Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth, 1.5m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth, lead up to 50m and lift up to 1.5m,as directed by Engineer-in-Charge. 14 All kinds of soil 15 Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : 16 All kinds of soil 17 Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia 18 Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50m outside the periphery of the area cleared. 19 Uprooting & removal of wild growth & vegetations, plants, on bldg at any level upto 15 M by necessary scafolding and swing and providing & applying a dilute hydrochloric acid on the root area etc complete as directed by Engineer in charge. 20 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 21 1:2:4 (1 cement : 2 coarse sand(zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) 22 Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor, etc., up to floor five level, excluding the cost of centering, shuttering and finishing : 23 1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) 24 Centering and shuttering including strutting, propping etc. and removal of form for : 25 Lintels, beams, plinth beams, girders, bressumers and cantilevers 26 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. 27 Thermo-Mechanically Treated bars of grade Fe-500D or more. 28 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: 29 Cement mortar 1:6 (1 cement : 6 coarse sand) 30 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : 31 Cement mortar 1:6 (1 cement : 6 coarse sand) 32 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approvedmake, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. 33 Deduct for not providing hinges in doors, windows or clerestory window shutters with : 34 ISI marked Stainless steel butt hinges with stainless steel screws : 35 For 2nd class teak wood and other class of wood shutters 36 Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 37 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws 38 Providing and fixing nickel plated M.S. pipe curtain rods with nickel plated brackets : 39 25 mm dia (heavy type) 40 Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete (Copper oxidised as per IS 1378) 41 300x16 mm 42 Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete (Copper oxidised as per IS 1378) 43 250x10 mm 44 150x10 mm 45 Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete (Copper oxidised as per IS 1378) 46 125 mm 47 Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessaryaccessories and screws etc. complete. 48 Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete : 49 250x16 mm 50 Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete : 51 300x10 mm 52 Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. 53 Twin rubber stopper 54 Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : 55 For fixed portion 56 Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) 57 Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS:12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. 58 Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side. 59 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): 60 With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) 61 Providing and fixing Brass 100mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete. 62 Providing and fixing aluminium round shape handle of outer dia 100mm with SS screws etc. complete as per direction of Engineer-in-charge 63 Anodized (AC 15 ) aluminium 64 Repairing of Aluminium door shutter with frame for smooth operation including taking out door with frame, dismembering aluminium door sections, taking out panelling, reassembling the door shutter with required aluminium cleats /iron flat /iron angle with screws, rivets & refixing the available panelling in position with snap beading thereafter refixing the shutter in position with necessary fixtures including pivots , necessary screws etc,all complete as directed by the Engineer In charge. (a) Single or Double Shutter up to 3.00 Sqm area 65 Refixing of old aluminium partition consisting of doors, windows,ventilators, partitions and wall panelling etc. fixed with rawl plugs,screws or with fixing clips, or with expansion hold fastners including necessary filling up of gaps at junctions, top, bottom and sides with required PVC/neoprene felt etc.including cost of fixing old particle board and Glass sheet in panelling of aluminium frame work, cutting in required sizes, frame work, cutting in required sizes, C.P. brass/stainless steel screws cleats etc. complete as per direction of Engineer-in-charge. (item include the cost of PVC felt/neoprene, screws, aluminium angle cleat,hold fastners but excluding the cost of aluminium sections and snap beading) (a) For Fixed Portion & Openable shutter portion. 66 Structural steel work in single section, fixed with or without connecting plate,including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete 67 Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. 68 In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works. 69 40 mm thick fine dressed stone flooring over 20 mm (average) thick base of cement mortar 1:5 ( 1cement : 5 coarse sand) with joints finished flush. 70 Red sand stone 71 Providing and laying Ceramic glazed floor tiles of size 300x300 mm(thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement :4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigment etc.,., complete. 72 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 73 (i)Single socketed pipes. 74 75 mm diameter 75 110 mm diameter 76 Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 77 Coupler 78 110mm 79 Single tee with door 80 110x110x110 mm 81 Bend 87.5° 82 75 mm bend 83 110 mm bend 84 Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 85 75 mm 86 110 mm 87 12 mm cement plaster of mix : 88 1:6 (1 cement: 6 coarse sand) 89 20 mm cement plaster of mix : 90 1:4 (1 cement: 4 coarse sand) 91 White washing with lime to give an even shade: 92 New work (three or more coats) 93 Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer, of required shade and colour all complete : 94 New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre 95 Finishing walls with Acrylic Smooth exterior paint of required shade : 96 New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) 97 Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : 98 Two or more coats on new work. 99 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 100 Distempering with 1st quality acrylic distemper (ready mixed) having VOC (Volatile Organic Compound ) content less than 50 gram/ litre, of approved brand and of required shade and colour complete to give and even shade. 101 Old work (one or more coats) 102 Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour. 103 One coat. 104 Two coats. 105 White washing with lime to give an even shade : 106 Old work (one or more coats) . 107 Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. 108 Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : 109 One or more coats on old work. 110 Finishing walls with Acrylic Smooth exterior paint of required shade : 111 Old work (One or more coat applied @ 0.90 ltr/10 sqm). 112 Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-harge. 113 With cement mortar 1:4 (1cement: 4 coarse sand). 114 Renewing glass panes, with putty and nails wherever necessary including racking out the old putty: 115 Float glass panes of nominal thickness 4 mm (weight not less than 10kg/sqm). 116 Flush pointing with cement mortar 1:3 (1 cement : 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement for flat tile bricks on top of mud phaska : 117 With F.P.S. brick tiles 118 Cleaning of terrace/loft water storage tank (inside surface area) upto 2000 litre capacity at all heights with coconut brushes, duster etc., removal of silt, rubbish from the tank and cleaning the tank with fresh water disinfecting with bleaching powder @ 0.5gm per litre capacity of tank, including marking the date of cleaning on the side of tank body with the help of stencil and paint and disposing of malba, all complete as per direction of Engineer-in-Charge. (The old date already written on tank should be removed with paint remover or black paint and if date is not written with the stencil or old date is not removed deduction will be made @ Rs. 0.10 per litre if during cleaning any GI fittings or ball cock is damaged that is to be repaired by contractor at his own cost and nothing extra will be paid on this account) 119 Cleaning and de-silting of gully trap chamber, including removal of rubbish mixed with earth etc. and disposal of same, all as per the direction of Engineer-in-charge. 120 Cleaning of chocked sewer line by diesel running vehicle mounting hydraulic operated high pressure suction cum jetting sewer cleaning machine fitted with pump having 4000 litres suction capacity and 6000 litres water jetting tank capacity including skilled operator, supervising engineer etc. for cleaning and partial de-silting of manholes and de-chocking of sewer lines. De-chocking and flushing of sewer line from one manhole to another by high pressure jetting system of 2200 PSI for sewer line from 150mm dia upto 300mm dia for all depth. 121 Dismantling W.C. Pan of all sizes including disposal of dismantled materials i/c malba all complete as per directions of Engineer-in- Charge. 122 Taking out existing wooden door shutter, repair by cutting, painting etc. and refixing of repaired door shutters to existing door frames, including replacement of hinges with screws, etc. as required, all complete as per the direction of the Engineer-in-charge. 123 Providing and fixing white vitreous china water closet squatting pan (Indian type) : 124 Orissa pattern W.C. pan of size 580x440 mm 125 Providing and fixing white vitreous china pedestal type (European type/ wash down type) water closet pan. 126 Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. 127 Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete. 128 10 litre capacity - White 129 Providing and fixing solid plastic seat with lid for pedestal type W.C. pan complete : 130 White solid plastic seat with lid 131 Providing and fixing white vitreous china wash basin including making all connections but excluding the cost of fittings : 132 Flat back wash basin of size 550x400 mm. 133 Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. 134 Flexible pipe 135 32 mm dia 136 Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. 137 Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour. 138 Waste coupling 31 mm dia of 79 mm length and 62 mm breadth weighing not less than 45 gms. 139 Credit of old un- serviceable materials recovered from dismantling / demolishing from work: 140 Old rusted ( unserviceable ) C.I/S.C.I pipes and fitting , Mild Steel / Steel Section, G.I/M.S pipes/ G S sheet/Profile Sheet etc. 141 Low level PVC flush tanks (10 litres) 142 Old damaged, broken,unserviceable PVC tank capacity upto 500 litre 143 Credit of old unserviceable wooden door shutters of area 3 Sqm or below, recovered from dismantling of partition/door shutters. 144 Repairing of old CI/PVC flushing cistern including replacing syphon and ball valve etc. including cleaning of cistern internal wall with required acid etc., all complete as per direction of Engineer-in-charge. 145 Providing and fixing of M.S. / C.I /Angle bracket to wash basin/sink i/c removal of old damaged bracket and refilling, finishing of hole etc. ,all complete as per direction of E-I-C. 146 Cleaning and de-silting of chocked WC Seat, trap chamber, including removal of rubbish mixed with earth etc. and disposal of same, all complete as per the direction of Engineer-in-charge. 147 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. : Internal work - Exposed on wall 148 20 mm nominal outer dia. Pipes. 149 25 mm nominal outer dia .Pipes. 150 32 mm nominal outer dia. Pipes. 151 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge : External work 152 25 mm nominal outer dia. Pipes. 153 32 mm nominal outer dia. Pipes. 154 40 mm nominal outer dia. Pipes. 155 Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. 156 Providing and fixing covers for PVC water storage tanks with necessary MS / PVC clamps 157 For 500 litres capacity tanks 158 Providing and fixing PTMT bib cock of approved quality and colour. 159 15mm nominal bore, 86 mm long. Weighing not less than 88 gms. 160 Providing and fixing PTMT stop cock of approved quality and colour. 161 15 mm nominal bore, 86 mm long. Weighing not less than 88 gms. 162 Providing and fixing PTMT pillar cock of approved quality and colour . 163 15mm nominal bore, 107 mm long. Weighing not less than 110 gms. 164 Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball. 165 20 mm nominal bore, 120 mm long. Weighing not less than 198 gms. 166 25 mm nominal bore, 152 mm long. Weighing not less than 440 gms. 167 Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour. 168 15 mm nominal bore with 45 cm length. 169 Providing and fixing PTMT extension nipple for water tank pipe, fittings of approved quality and colour. 170 20mm nominal bore. Weighing not less than 40 gms. 171 Cutting holes up to 30x30 cm in walls including making good the same: 172 With common burnt clay F.P.S. (non modular) bricks. 173 Providing and fixing CPVC gate valve/ ball valve (Plastic) of supreme or equivalent make all complete as per direction of Engineer-in-Charge. 174 For 20 mm outer dia pipe 175 25 mm Dia . Outer Dia 176 32 mm outer dia pipe. 177 Providing and fixing CPVC Union of Supreme or equivalent make in CPVC pipe including jointing with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in charge. 178 For 20 mm outer dia pipe 179 25 mm Dia Outer Dia 180 For 32 mm outer dia pipe 181 Cleaning of chocked G.I./CPVC water supply line by manual or mechanical or gas/ water pressure means including removal of rubbish,sand,earth etc and disposal of same all complete as per direction of Engineer in charge. (A) Dia of pipe 15 mm to 32 mm . 182 Arranging welding machine for welding of Broken steel componants such as Handels, fastners, hinges, grills, etc.as and where required as per the direction of Engineer-in-Charge. (rate includes labour & transportation of machine at site). 183 Cleaning of terrace / spouts / khurras / canopies / blocked chajjas including removal of algae, fungal element etc., by iron brush, broom, bleaching powder etc, and removing leaves, grass, dust, rubbish and other deposited and accumulated material etc.,also disposal of rubbish to dumping ground up to a lead of 50m.,all complete as per direction of E-I-C.
