|
| 1 | Electrical WorkProviding and fixing of commercial RO water purifier Including Inbullt Purification capacity-45-50 litre/hour, Ro+uv+uf +tds adjuster., suitable for borewell water.Installation Type Wall Mounted. MAKE- Kent, Purelt, Haler or any other equivalent brands. |
| 2 | SITC of Early Streamer Emission (ESE) LIGHTNING ARRESTER which is an active lightning conductor designed to conform to the French Standard NF C 17-102:2011/UNE 21186:2011 ∆T:60 µs for ESE lightning conductors. Its working principle evolves from local electrostatic field that develops naturally around the system as a thunderstorm begins to gather. In the event of descending lightning, an inbuilt triggering device generates high tension pulses at the conductor tip, causing a ‘corona effect’. The international testing laboratory is being duly accredited. Protection radius of 79 Mtr at level 1 & 107 Mtr at level 4.as per pre approved by Engineer in-charge MAKE – NAVA ,RESOLVE EARTHING, ABB |
| 3 | Supply & Fixing of ESE Lightning Strike Counter -Lightning Discharge Counter Self-powered non re settable Lightning Event Counter (6 digits) mounted on down conductor in IP 67 enclosure with minimum sensitivity 1 kA for10/350 μs pulse.as per pre approved by Engineer in-charge (Analog- Type- Digit -6)MAKE – NAVA ,RESOLVE EARTHING, INDIA,ABB |
| 4 | Supply & Fixing SUPPORTING MAST 5Mtr mast with base plate and accessories with bake light with bake light insulator |
| 5 | Supply & Fixing Bakelite Insulator |
| 6 | Providing & Laying P.V.C. / XLPE insulated & P.V.C. sheathed Un-armoured Single core 70 sqmm Copper cable confirming to IS:1554 P-I / IS :7098 P - I of 1.1 KV with electrolytic grade Copper made of copper rods confirming to IS 613-1964, of purity >99.7 %, Inner / outer sheath confirming to IS:5831 in existing RCC / Hume / Stoneware / PVC pipe/ open duct/cable trench / Cable tray (with cable tie) including testing etc. as required of following size.as per pre approved by Engineer in-charge |
| 7 | CCTV and LANSupply of 18\" Full HD LED/ LCD Security Monitor , LED Backit TFT LCD technology with1366x768 resolution, Wide view angle 90\" (H)/65\"(V), 3D comb filter , 3D De-interface, 3D noise reduction, HDMI , VGA input, High reliable component for 7x24 working, Brightness 200cd/m2 or better, Contrast: 800:1 or better color 15.7m or better. VESA stand , power consumptionnot more than 25W, with HDMI Cable and mounting accessories Approved Makes : LG, Samsung, HIKVISION/Honey wall |
| 8 | Supply, Installation, Integration, Testing, & Commissioning of 8 TB HDD for Video Recorder as per requirement, scope of work, technical specificationand with 3 years onsite OEM warranty. Make- WD, FEAGATE |
| 9 | Distribustion Switch - The Switch should have atleast 16 10/100/1000-BaseX Ports,The Switch should support 8 combo port (GT/SFP) & 4 x 10G (SFP+),The Switch should support AC + 12VDC RPS power supply,The Switch should have RJ45 Ports for Management,The Switch should have atleast 32 MB of Flash for storing OS and other Logs,The Switch should have atleast 512 MB of DRAM,The Switch should have power savings mechanism wherein it should reduce the power consumption on ports not being used,The Switch should be Rack Mountable and should not take space more than 1RU,The Switch should support operating temperature from 0°to 45°C,The Switch should support operating relative humidity 15% to 90% noncondensing,The Switch should have atleast 95Mpps of forwarding rate,The Switch should support atleast 16000 MAC Addresses,The Switch should support atleast 500 IPv4 routes,The Switch should support atleast 4000 VLAN IDs & 1000 SVI’s,The Switch should support 9198 bytes of Jumbo Frames,The Switch should support Maximum Transmission Unit (MTU) of 9198 bytes,The Switch architecture should be able to stack atleast 4 units of switches in stack,The Switch stacking should support 20 Gbps of throughput,The Switch stacking should support single IP address management for the group of switches,The Switch should support IPv6 Routing capable protocols such as OSPFv3 in hardware,The Switch should support IPv6 Multicast Routing,The Switch should support basic IP Unicast routing protocols (static, RIPv1 & RIPv2) ,The Switch should support IPv6 & IPv4 Policy Based Routing,The Switch should support Inter-VLAN routing,The Switch should support VRRPv3,The Switch should be able to discover (on both IPv4 & IPv6 Network) the neighboring device giving the details about the platform, IP Address, Link connected through etc, thus helping in troubleshooting connectivity problems,The Switch should support Detection of Unidirectional Links (in case of fiber cut) and to disable them to avoid problems such as spanning-tree loops,The Switch should support centralized VLAN Management, VLANs created on the core switch should be propagated automatically,The Switch should support 802.1d, 802.1s, 802.1w Spanning-Tree & its enhancement for fast convergence,The Switch should support 802.1q VLAN encapsulation,The Switch should support 802.3ad (LACP) to combine multiple network links for increasing throughput and providing redundancy,The Switch should have Port security to secure the access to an access or trunk port based on MAC address to limit the number of learned MAC addresses to deny MAC address flooding,The Switch should support DHCP snooping to prevent malicious users from spoofing a DHCP server and sending out rougue addresses,The Switch should support Reverse Path Forwarding (RPF) feature to mitigate problems caused by the introduction of malformed or forged (spoofed) IP source addresses into a network by discarding IP packets that lack a verifiable IP source address,The Switch should support flexible & multiple authentication mechanism, including 802.1X, MAC authentication bypass, using a single, consistent configuration,The Switch should support RADIUS change of authorization and downloadable Access List for comprehensive policy management capabilities,The Switch should support MAC address notification to allow administrators to be notified of users added to or removed from the network,The Switch should support IGMP filtering to provide multicast authentication by filtering out nonsubscribers and limits the number of concurrent multicast streams available per port,The Switch should support VLAN ACLs on all VLANs prevent unauthorized data flows from being bridged within VLANs,The Switch should support IPv6 ACLs that can be applied to filter IPv6 traffic,The Switch should support Port-based ACLs for Layer 2 interfaces to allow security policies to be applied on individual switch ports,The Switch should support Secure Shell (SSH) Protocol, and Simple Network Management Protocol Version 3 (SNMPv3) to provide network security by encrypting administrator traffic during Telnet and SNMP sessions,The Switch should support TACACS and RADIUS authentication to facilitate centralized control of the switch and restricts unauthorized users from altering the configuration,The Switch should support Multilevel security on console access to prevent unauthorized users from altering the switch configuration,The Switch should be capable of Downloading Downloadable Access List from network security engine based on user identity,The Switch should support 802.1p CoS and DSCP Field classification using marking and reclassification on a per-packet basis by source and destination IP address, MAC address, or Layer 4 Transmission Control Protocol/User Datagram Protocol (TCP/UDP) port number,The Switch should support 1.5 MB of buffers on the 24 port model,The Switch should be capable of enabling feature on all ports of the switch for Ingress and Egress Traffic,The Switch should be capable of monitoring network traffic on Physical, VLAN,The Switch should be capable of measuring user traffic performance and generating alerts (based on thresholds) and reports,Standards & Compliance (Switch Should support all the mentioned Standards) Likes IEEE 802.1s,IEEE 802.1w,IEEE 802.1x,IEEE 802.3ad,IEEE 802.3x full duplex on 100BASE-X, and 1000BASE-X ports,SNMPv1, SNMPv2c, and SNMPv3, ,Architecture- 1-port mini-GBIC LX Single-mode Fiber Transceiver,Connector-It should have duplex LC Connector,Flow control-Support 802.3x,Mode-9/125 um Single mode Fiber Type up to 20 KM,Support-:1310nm,Power-3.3V,Architecture-1-port mini-GBIC LX SFP + LC TypeTransceive, Connector-It should have duplex LC Connector,Speed-Should support data transfer speed of 10 Gbps-Support 802.3e,Mode-9/125 um Single mode Fiber Type up to 10 KM,Support wavelenght-:1310nm,Power-3.3V, StorageRelativeHumidity- supports5% to 95% |
| 10 | Supply, Drawing High-Speed HDMI Cable Support Full HD 1080pConnectors for Superior Conductivity Suitable For : Dvd, Blu-Ray, Tv, Hdset Top Box, Camcorder, Hdtv, Ps3 Console, Xbox ConsoleIn The Box : High-Speed HDMI Cable Terabyte HDMI cables are compatible with resolutions 480p, 720p, 1080i and 1080p. Perfect for both high definition video and standard video formats. MAKE - Digisol ,Mercusys , CP clus |
| 11 | Interior Partitons and Furniture worksOfficer Working Table. Providing & placing officer working table made out of 18mm thick ISI marked Water Proof, Termite Proof, Borer free Plywood with 1.00mm thick decorative laminate of approved shade on external, internal and under surfaces all around of table duly pasted with ISI marked adhesive of approved make all work as per directions and satisfaction of Engineer Incharge. Brief Specifications of table are as under: a) Table size1800(W) x 1200 (D) x 750 (H) all dimensions in mm. b) All framework and supporting arrangements for table and top shall be made of seasoned 2nd Class teak wood duly primed with approved primer and finished with melamine polish in matt / gloss finish.c) The table top, side panels & front modesty shall be made up of 18mm thick ISI marked Plywood with 1.00mm thick decorative laminate on external,internal and under surfaces of table duly pasted. d) CPU & Keyboard Arrangements. Integrated wooden shelf for CPU & foldable arrangements for placing keyboard separately made out of 18mm thick ISI marked plywood & 1.00 mm thick decorative laminate all around shall be provided. e) Under Table Storage : One Under table Drawer type storage cabinet having 03 Nos. drawers. The internal dimenisions of top two & last drawers shall be 350(W) x 480(D) x 150(H) & 350(W) x 480(D) x 350(H)in mm respectively. The storage cabinet shall be made of 18mm thick plywood with 1.00mm decorative laminate on outer, inner and all surfaces. All drawers, shelves, doors etc shall be made with 18mm thick plywood with 1.00mm thick laminate on inner surfaces. All Drawers shall run ontelescopic channel set. The telescopic channels shall be of make Hettich/ Godrej/ Hafele/Dorset/ Ozone . The drawers and shutters shall have proper metallic brass/ Copper/ Stainless Steel/ Brushed finish handles of adequate size and proper seperate locking arrangements.f) Electrical & Other Accessories arrangements. The table shall have proper concealled provisions for accommodating Power, telephone, LAN, audio & video cables, electrical points with switches, sockets, ports for electric, telephone, Intercoms, LAN, Computer Systems, monitors, PBAX, Printers etc. of approved make and requirements.Suitable Space shall be provided for visitor chairs. All edges shall be sealed with 2nd class teak wood rounded moulding. The edge moulding shall be treated and finished with Melamine Polish.All work complete including Fabrication, nailing, screwing, pasting, transporting, loading, unloading, placing, finishing, setting, etc complete in all due respect as per technical specifications, directions and satisfaction of Engineer Incharge. |
| 12 | Officer Working Table. Providing & placing officer working table made out of 18mm thick ISI marked Water Proof, Termite Proof, Borer free Plywood with 1.00mm thick decorative laminate of approved shade on external, internal and under surfaces all around of table duly pasted with ISI marked adhesive of approved make all work as per directions and satisfaction of Engineer Incharge. Brief Specifications of table are as under: a) Table size1500(W) x 900 (D) x 750 (H) all dimensions in mm. b) All framework and supporting arrangements for table and top shall be made of seasoned 2nd Class teak wood duly primed with approved primer and finished with melamine polish in matt / gloss finish.c) The table top, side panels & front modesty shall be made up of 18mm thick ISI marked Plywood with 1.00mm thick decorative laminate on external,internal and under surfaces of table duly pasted. d) CPU & Keyboard Arrangements. Integrated wooden shelf for CPU & foldable arrangements for placing keyboard separately made out of 18mm thick ISI marked plywood & 1.00 mm thick decorative laminate all around shall be provided. e) Under Table Storage : One Under table Drawer type storage cabinet having 03 Nos. drawers. The internal dimenisions of top two & last drawers shall be 350(W) x 480(D) x 150(H) & 350(W) x 480(D) x 350(H)in mm respectively. The storage cabinet shall be made of 18mm thick plywood with 1.00mm decorative laminate on outer, inner and all surfaces. All drawers, shelves, doors etc shall be made with 18mm thick plywood with 1.00mm thick laminate on inner surfaces. All Drawers shall run ontelescopic channel set. The telescopic channels shall be of make Hettich/ Godrej/ Hafele/Dorset/ Ozone . The drawers and shutters shall have proper metallic brass/ Copper/ Stainless Steel/ Brushed finish handles of adequate size and proper seperate locking arrangements.f) Electrical & Other Accessories arrangements. The table shall have proper concealled provisions for accommodating Power, telephone, LAN, audio & video cables, electrical points with switches, sockets, ports for electric, telephone, Intercoms, LAN, Computer Systems, monitors, PBAX, Printers etc. of approved make and requirements.Suitable Space shall be provided for visitor chairs. All edges shall be sealed with 2nd class teak wood rounded moulding. The edge moulding shall be treated and finished with Melamine Polish.All work complete including Fabrication, nailing, screwing, pasting, transporting, loading, unloading, placing, finishing, setting, etc complete in all due respect as per technical specifications, directions and satisfaction of Engineer Incharge. |
| 13 | Officer Working Table. Providing & placing officer working table made out of 18mm thick ISI marked Water Proof, Termite Proof, Borer free Plywood with 1.00mm thick decorative laminate of approved shade on external, internal and under surfaces all around of table duly pasted with ISI marked adhesive of approved make all work as per directions and satisfaction of Engineer Incharge. Brief Specifications of table are as under: a) Table size1200(W) x 750 (D) x 750 (H) all dimensions in mm. b) All framework and supporting arrangements for table and top shall be made of seasoned 2nd Class teak wood duly primed with approved primer and finished with melamine polish in matt / gloss finish.c) The table top, side panels & front modesty shall be made up of 18mm thick ISI marked Plywood with 1.00mm thick decorative laminate on external,internal and under surfaces of table duly pasted. d) CPU & Keyboard Arrangements. Integrated wooden shelf for CPU & foldable arrangements for placing keyboard separately made out of 18mm thick ISI marked plywood & 1.00 mm thick decorative laminate all around shall be provided. e) Under Table Storage : One Under table Drawer type storage cabinet having 03 Nos. drawers. The internal dimenisions of top two & last drawers shall be 350(W) x 480(D) x 150(H) & 350(W) x 480(D) x 350(H)in mm respectively. The storage cabinet shall be made of 18mm thick plywood with 1.00mm decorative laminate on outer, inner and all surfaces. All drawers, shelves, doors etc shall be made with 18mm thick plywood with 1.00mm thick laminate on inner surfaces. All Drawers shall run ontelescopic channel set. The telescopic channels shall be of make Hettich/ Godrej/ Hafele/Dorset/ Ozone . The drawers and shutters shall have proper metallic brass/ Copper/ Stainless Steel/ Brushed finish handles of adequate size and proper seperate locking arrangements.f) Electrical & Other Accessories arrangements. The table shall have proper concealled provisions for accommodating Power, telephone, LAN, audio & video cables, electrical points with switches, sockets, ports for electric, telephone, Intercoms, LAN, Computer Systems, monitors, PBAX, Printers etc. of approved make and requirements.Suitable Space shall be provided for visitor chairs. All edges shall be sealed with 2nd class teak wood rounded moulding. The edge moulding shall be treated and finished with Melamine Polish.All work complete including Fabrication, nailing, screwing, pasting, transporting, loading, unloading, placing, finishing, setting, etc complete in all due respect as per technical specifications, directions and satisfaction of Engineer Incharge. |
| 14 | Center table glassCENTRE TABLE - Size- (L)1100mmx(D)600mmx(H)440mmSupplying and placing in position of Waiting Room center table as per photograph.Center Table glass shall be10- 12mm thick toug+B46hened, edge beveled and in rectangular shaped. Another glass attached with chrome plated metal rods with UV welding and using as a bookshelf. The product should be from BIFMA certified company. |
| 15 | Side Tables Size 2\"-2\" |
| 16 | Providing, Supplying & Installation of High back breathable mesh fabric upholstered Ergonomic revolving chair1. High back breathable mesh fabric upholstered Ergonomic revolving chair. 2. Dimensions of Chairs: a) Seat:Width 500 mm +/- 10mm, Depth 480mm +/- 10mmb) Back Rest: Width 500mm +/- 10mm, Height from Seat 700mm +/- 10mmc) Minimum Seat Height 470mm +/- 10mm & Maximum Seat height 570mm +/- 10mm3. Seat shall be made up of 12 mm thick hot pressed anti- termite water resistant plywood, upholstered with breathable mesh type fabric and moulded polyurethane foam.4. Chair back shall be made of 40 mm thick edge of PVC moulding with breathable Mesh fabric upholstery. The polyurethane foam density shall be 45 +/- 2kg/m3. Chair Back shall be fixed with lumber support & fixed with Head rest for extra support. Lumber support ( 260mm W * 150mm H )attached headrest shall be supported with 2 chrome plated rods of 20mm thicknessfrom headrest to seat base. 5.PU padded Adjustable handles (260 mm W * 85mm D) shall operate through push button. Chair shall have regular tilt mechanism feature: 360 degree revolving type with single position locking & Chrome base fixed with 5 nos. Nylon castors.6. Breathable Mesh Chair Backrest Moulds shall provide adequate back support, and makes the long hours of seating comfortable.All work complete including Fabrication, nailing, screwing, pasting, transporting, loading, unloading, placing, finishing, setting, etc complete in all respect as per technical specifications, standards, directions and satisfaction of Engineer Incharge. |
| 17 | Providing, Supplying & Installation of Medium back breathable mesh fabric upholstered Ergonomic revolving chair1. Medium Rise revolving chair.2. Dimensions of Chairs: a) Seat:Width 500 mm +/- 10mm, Depth 480mm +/- 10mmb) Back Rest: Width 420mm +/- 10mm, Height from Seat 550mm +/- 10mmc) Minimum Seat Height 470mm +/- 10mm & Maximum Seat height 570mm +/- 10mm3.Seat shall be made up of 12 mm thick hot pressed anti- termite water resistant plywood, upholstered with Breathable Mesh fabric and moulded polyurethane foam. The polyurethane foam density shall be 45 +/- 2kg/m3.4. Chair back shall be made of 40 mm thick edge of PVC moulding with Breathable Mesh upholstery. The seat and back are arrested together with a 9.0cm (W) spine made of 0.8cm thick HR steel. Breathable Mesh Chair Backrest Moulds shall provide adequate back support, and makes the long hours of seating comfortable.5. PU padded Adjustable handles (300mm W * 75mm D ) shall operate through push button.6. Chair shall have regular tilt mechanism feature: 360 degree revolving type with single position locking&Chrome base fixed with 5 nos. Nylon castors. The pedestal is 67.0cm pitch-center dia (77.0 cm with castor). The twin wheel castors are injection moulded in Black NylonAll work complete including Fabrication, nailing, screwing, pasting, transporting, loading, unloading, placing, finishing, setting, etc complete in all due respect as per technical specifications, standards, directions and satisfaction of Engineer Incharge. |
| 18 | Medium back chair revolvingMEDIUM BACK CHAIR leatherette chair Providing and placing Mid Back chair. COLOUR BLACKThe seat and back shall be made up of 1.2cm.thick hot pressed plywood upholstered with pure leatherette of required color and moulded Polyurethane foam. BACK SIZE: 53.0cm (W) X 73.0cm (H), SEAT SIZE: 54.6cm (W) X 49cm (D). The High Resilience Polyurethane foam is moulded with density=45+/-2 kg/m cube and hardness load 16+/-2 kgf as per IS: 7888 for 25% compression. The seat and back are arrested together with a 9.0cm (W) spine made of 0.8cm thick HR steel. The armrest tube assembly is made of 2.54cm x 0.16cm. M.S. E.R.W. support tubes and Chrome plated. The armrest top is made of ABS & upholstered with foam &leatherette . The pedestal is made of die-cast aluminum with buffing finished. It is fitted with 5nos. twin wheel castors. The pedestal is 67.0cm pitch-center dia (77.0 cm with castor). The twin wheel castors are injection moulded in Black Nylon. All work complete including Fabrication, nailing, screwing, pasting, transporting, loading, unloading, placing, finishing, setting, etc complete in all due respect as per technical specifications, standards, directions and satisfaction of Engineer Incharge. |
| 19 | Non revolving Visitor ChairVisitor Chair shall be of dimensions (560mm W x 670mm D x 1020 mm H )Seat & Back Assembly : The seat & back shall be made of 12 mm thick hot-pressed plywood upholstered with Mesh type fabric cover & moulded polyurethane foam. The polyurethane foam density shall be of 45+/-2 kg/m3, The back foam shall be designed with contour lumber support for extra cushioning, Under structure shall be of MS elliptical/oblong pipe (40x20x1mm thick) chrome plated frame. All work complete including Fabrication, nailing, screwing, pasting, transporting, loading, unloading, placing, finishing, setting, etc complete in all due respect as per technical specifications, standards, directions and satisfaction of Engineer Incharge. |
| 20 | High back mesh revolving chair1. High Rise rvolving chair. 2. High Back Chair shall be of dimensions – 500 mm W* 500mm D *1125mm H approximately3. Seat shall be made up of 12 mm thick hot pressed anti- termite water resistant plywood, upholstered with leatherette and moulded polyurethane foam.4. Chair back shall be made of 40 mm thick edge of PVC moulding with Mesh upholstery. The polyurethane foam density shall be 45 +/- 2kg/m3. Chair Back shall be fixed with lumber support & fixed with Head rest for extra support. Lumber support ( 260mm W * 150mm H )attached leatherette headrest shall be supported with 2 chrome plated rods of 20mm thicknessfrom headrest to seat base. 5.PU padded Adjustable handles (260 mm W * 85mm D ) shalloperate through push button. Chair shall have regular tilt mechanism feature : 360 degree revolving type with single position locking&Chrome base fixed with 5 nos. Nylon castors .6. Netted Chair Backrest Moulds shall provide adequate back support, and makes the long hours of seating comfortable.All work complete including Fabrication, nailing, screwing, pasting, transporting, loading, unloading, placing, finishing, setting, etc complete in all due respect as per technical specifications, standards, directions and satisfaction of Engineer Incharge. |
| 21 | Medium back mesh revolving Conference Halls chair1. Medium Rise revolving chair.2. Dimensions of Chairs: a) Seat:Width 500 mm +/- 10mm, Depth 480mm +/- 10mmb) Back Rest: Width 420mm +/- 10mm, Height from Seat 550mm +/- 10mmc) Minimum Seat Height 470mm +/- 10mm & Maximum Seat height 570mm +/- 10mm3.Seat shall be made up of 12 mm thick hot pressed anti- termite water resistant plywood, upholstered with Mesh fabric and moulded polyurethane foam. The polyurethane foam density shall be 45 +/- 2kg/m3.4. Chair back shall be made of 40 mm thick edge of PVC moulding with Mesh upholstery. The seat and back are arrested together with a 9.0cm (W) spine made of 0.8cm thick HR steel. Netted Chair Backrest Moulds shall provide adequate back support, and makes the long hours of seating comfortable.5. PU padded Adjustable handles (300mm W * 75mm D ) shall operate through push button.6. Chair shall have regular tilt mechanism feature: 360 degree revolving type with single position locking&Chrome base fixed with 5 nos. Nylon castors. The pedestal is 67.0cm pitch-center dia (77.0 cm with castor). The twin wheel castors are injection moulded in Black NylonAll work complete including Fabrication, nailing, screwing, pasting, transporting, loading, unloading, placing, finishing, setting, etc complete in all due respect as per technical specifications, standards, directions and satisfaction of Engineer Incharge. |
| 22 | Sofa setSingle seater SOFA SETProviding and placing of Sofa\"s with Seat Height of 450mm. Slab stock foam with density 60+/-2Kg/m3 at seats and cushions. Seats and Cushion is also provided with 100% hollow recron fillers for extra comfort. Sofa structure consists of Tropical 12mm ply frame at the bottom on which S-Springs and Tie bars are provided then the complete structure is provided with layers of Non woven fabric, 2 Layers of Slab Stock Foam 80-100mm and finally recron is assembled together to form the final sofa. Seat and Cushions is upholstered with PVC Leatherite (shade should be approved from buyer) upholstery, Spring assembly of 4mm Dia is mounted in understructure for support and additonal cushioning purpose. Legs shall be provided made of Stainless Steel (Grade SS 202). It is a welded assembly made by the combination of Tube and Plate. |
| 23 | Sofa set02 seater SOFA SETProviding and placing of Sofa\"s with Seat Height of 450mm. Slab stock foam with density 60+/-2Kg/m3 at seats and cushions. Seats and Cushion is also provided with 100% hollow recron fillers for extra comfort. Sofa structure consists of Tropical 12mm ply frame at the bottom on which S-Springs and Tie bars are provided then the complete structure is provided with layers of Non woven fabric, 2 Layers of Slab Stock Foam 80-100mm and finally recron is assembled together to form the final sofa. Seat and Cushions is upholstered with PVC Leatherite (shade should be approved from buyer) upholstery, Spring assembly of 4mm Dia is mounted in understructure for support and additonal cushioning purpose. Legs shall be provided made of Stainless Steel (Grade SS 202). It is a welded assembly made by the combination of Tube and Plate. |
| 24 | Sofa set03 seater SOFA SETProviding and placing of Sofa\"s with Seat Height of 450mm. Slab stock foam with density 60+/-2Kg/m3 at seats and cushions. Seats and Cushion is also provided with 100% hollow recron fillers for extra comfort. Sofa structure consists of Tropical 12mm ply frame at the bottom on which S-Springs and Tie bars are provided then the complete structure is provided with layers of Non woven fabric, 2 Layers of Slab Stock Foam 80-100mm and finally recron is assembled together to form the final sofa. Seat and Cushions is upholstered with PVC Leatherite (shade should be approved from buyer) upholstery, Spring assembly of 4mm Dia is mounted in understructure for support and additonal cushioning purpose. Legs shall be provided made of Stainless Steel (Grade SS 202). It is a welded assembly made by the combination of Tube and Plate. |
| 25 | Office Work station Panel Based partition with Under Drawer type StoragePanel Based partition of 60mm thickness with framework made up of aluminium alloy extrusions. All Aluminium parts are pretreated for epoxy polyester powder coated of 40-60micron thickness. All these frame work sections are fitted to each other by screws which is properly zinc coated for corrosion resistant.One single frame consists of following Components :-1.Vertical Members in aluminum alloy extrusion (thickness 1.6mm).2. Top Horizontal Member in aluminum alloy extrusion of size 60x30mm(thickness 1.3mm).3. Mid Member in aluminum alloy extrusion of size 60x22mm (thickness 1.3mm) having provision to support the worktop with engineered design Support bracket.4. Bottom Raceway in aluminum alloy extrusion of size 140mm ht. x 60mm (thickness 1.2mm).5. Intermediate Raceway In aluminum of size 140mm ht above / below the work top as per requirement.6. TilesTHE BOTTOM tiles can be provided in following options:- (a) Prelaminated 9mm thick ISI Marked Plywood with decorative laminate on top and white balancing on unexposed face, The tiles are supported within groove in aluminium extrusion. (b) Metal tiles are made up of CRCA of 0.8mm thickness duly powder coated. The tiles are supported within groove in aluminium extrusion.THE UPPER tiles can provided in following options:- (a)The Fabric tile are made of 12mm high density soft board inside upholstered with response fabric supported with staple pins.The tiles are supported within groove in aluminium extrusion. (b)The Marker tile are made up of 9mm thick ISI marked Plywood pasted with 1mm white marker laminate, on the the exposed face The tiles are supported within groove in aluminium extrusion.(c) Fabric on Magnetic board tile are made up of GI sheet of 0.8mm inside upholstered with response fabricsupported with staple pins. The tiles are supported within groove in aluminium extrusion.7.Top& End Trims -The exposed vertical and horizontal faces of the frames. The trims are made of aluminum extrusions of size 60x19mm(thickness 1.5mm) and are covered with ABS caps on joints and ABS end trims.8.Connectors:--Partitions are supported by Universal poles & MS bracket of 2mm thick zinc plated wherever required i.e,(L,T,+,180deg) for stability. At 2 Way joint of 90deg- Aluminium alloy extrusion of 60x60mm is provided which is fitted to main frame and epoxy powder coated. At 3 way joint of 90deg- Aluminium alloy extrusion of 60x60mm is provided which is fitted to main frame and epoxy powder coated. At 4 way joint of 90deg- Aluminium alloy extrusion frame Vertical member is fitted with M S connectors at top andWIRE MANAGEMENT - Partition has concealed wire management capabilities and are engineered for responsive and safe operations of power, telecommunications and data (LAN) and has separate components for electrical, data and telephone cables having adequate capability of both the vertical and horizontal wire movements. Slots/cutouts are provided on Raceways to fix all electrical and data points.LEVELLERS - Levellor of M10 size are provided in each frame which allow 10-25mm adjustment for floor unevenness.Work topWork top shall be of 25mm thick Particle board of exterior grade conforming to IS 12406 with laminate finish of approved colour shade and pattern. Work Top shall have 2mm PVC edging of approved make, quality ,shade and colour on exposed area and 1mm on covered area. The Work top shall be supported with suitable M.S. bracket of standard size made of CRCA sheet of minimum 2mm thick Grade A as per IS 513 with powder coated finish of approved colour. Suitable size of metal inserts to be provided in worktop for fixing with the partition/gable end. Fixing directly with screws is not permissible. |
| 26 | StorageProviding and fixing storage unit in Librarary sizes of 600 mm deep and 2100 (h), made out of 18mm thk. Plyboard and back made up of 8mm ply, unit is provided with vertical and horizontal divisions as per design with drawers and shutters, lockable, with all hardware like hinges, tower bolt, magnetics catcher, lock of approved quality. The cabinet shoould be raised 75/100mm above ground. Inside exposed surfaces should be finished with putty , wood primer coats and finished with 3 coats of oil base colour paint with specified shade. exposed outside surfaces should be Teak wood finished laminated (Golden Wange) with standard grade laminate of approved design and make. all exposed edges should be finished with first quality T.W. beadings of same finish (Golden Wange) to be finished with malemine polish as per design and specifications and instructions given by interior designer & as per drawing. |
| 27 | PartitionsSupply and fixing of partitions upto height as specified having an internal frame work of anti termite treated teak wood sections of 2\" x 1.5\" sections -2\" c/c distance both ways with a covering of 19mm commercial plyboard and a pattern oflaminates, 1.0mm laminate on both sides of approved make and shadewith coloumns and bands as per design and a pattern of grooves etc. as per details and specifications . The grains of the laminate should be matched properly. Proper arrangement as per detail shall be made for providing electricla wires and misc. cables at 2\"6\" ht. and at skirting level. this is highlighted on the finished partition with the help of grooves/ projections as per detail.The grooves to be painted in approved color. Only well seasoned and treated wood to be usedand Complete as per specification and direction of Engineer-Incharge. |
| 28 | Providing, fixing of CNC cut jali work made out of 12mm thick mdf board with fixing to the surrounding woooden laminate panalling.and Complete as per specification and direction of Engineer-Incharge. |
| 29 | Wall PanellingProviding & fixing panelling on walls of 19mm plyboard with 1mm thick laminateas per design & drawing with sub-frame of size 40 x 25 mm hard wood & 450 mm center to center treated with anti - termite & fire retardant paint. The frame to be fixed on walls with screws and wooden gutties. Rate to include necessary notches in frame on carrying electrical conduit & switch boxes and Complete as per specification and direction of Engineer-Incharge. |
| 30 | Soft Board Panelling : P&F paneling over adequate leveled frame formed of 12mm thick cellotex board wrapped in fabric with all 4 sides of cellotex panel finished with wooden margin of appropriate size. All grooves to finished with veneer/fabric all around to match the main fabric paneling, unless specified otherwise. panelling to include veneered skirting as required and Complete as per specification and direction of Engineer-Incharge. |
| 31 | Providing and fixing of MDF Beading on wall with Paint finish and Complete as per specification and direction of Engineer-Incharge. |
