Tender For Major Repair Works Under State Budget Head (Budget Announcement 2025-26) At Gsss_Dhanta (Sirohi); 1 Demolishing R.C.C. work manually / by mechanical means includingstacking of steel bars and disposal of unserviceable material within 50 meters lead as per direction of engineer-in-charge. 2 Extra for cutting reinforcement bars manually / by mechanical means in R.C.C. or R.B. work (payment shall be made on the cross sectional area of R.C.C. o R.B. work ) as per direction of Engineer-in-charge. 3 Dismantling stone slab roofing over wooden karries and batten (dismantling karries and bettens to be paid for separately ) including stacking of serviceable material and disposal of unserviceable material within 50 meter lead: 4 Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 meter lead: 5 Slab Beam -Porviding and laying in position specified grade of cement concrete for RCC structural elements upto floor five level including curing , compation finishing with rendering in cement sand mortar 1:3 (1 cement :3 coarse sand ) and making good the joints and cost of plastizer (if required) excluding the cost of centering ,shuttering and reinforcement for Beams , suspended floors , roofs , griders having slopes upto 15,landing ,balconies ,shelves ,chajjas, lintels, bands, plain windows sills,staircases and spiral staircase etc.M20 grade Nominal Mix/ Design Mix 6 Centering & shuttering with plywood or steel sheets including strutting ,propping bracing both ways with steel props and removal of formwork for upto floor five level for: Suspended Floor ,roofs, landing, staircase, balconies, girders,cantilevers,bands, coping bed plates, anchor blocks , sills, chhajjas , lintel ,beam,plinth beam etc. 7 Providing and fabrication reinforcement for RCC wor including straighteing,cutting, bending,placing in position and binding (including cost of binding wire) all complete upto floor five level.(Original producerswho manufacture billet directly from iron ores and rollthe bilets to produce steel conforming to IS:1786) Thermo - mechanically Treated bars (conforming of relevent IS code) 8 Desmanting of flooring with care including stacking of servceable material and diposal of unserviceable material with in 50mtr. Lead for cement concrete flooring 9 Dismantling roofs with care including stacking of serviceable material and disposal of uncerviceable material with in 50mtr. Lead for: 10 Polished blue kota stone flooring, jaid over 20mm thick base of C.M. 1:4 and jointed with grey cement slurry to match the shade of the slab including rubbing and polishing complete for area of each slab up to 2001to 5000 Sq. Cm 11 PCC : Providing and laying in position cement concrete including curing,compaction ect. Complete in specified grade excluding the cost of centering and shuttering-All work up to plinth level. M10 grade Nominal Mix 1:3:6 (1 cement :3 coarse sand :6 graded stone aggregate 20mm nominal size). 12 Grading roof for water proofing treatment with water prooffing compaund cement concrete 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size). 13 Gola -Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 10mm and down gauge) including finishing with cement mortar 1:3 (1 cement :3 fine sand ) as per standarddesing: 14 Providing and laying broken glazed tiles on roof (broken glazed tiles not less than 9Kg/Sqm) on top of hot bitumen @1.7 Kg/Sqm.(1.40 Kg of VG- 40 (30/40) grade and 0.30 Kg/Sqm. Of VG-10 (80/100) grade) and joints filled with cement mortar 1:2 (1cement :2 marble dust mixed with water proofing compound all complete as per direction of engineer-in-charge. 15 Internal plaster: plaster on new surface on walls in cement sand mortar 1:6 including racking of joint ect. Complete fine finished 20mm thick 16 Plaster (celling): 6mm thick cement plaster to celling of mix 1:3 (1 cement : 3-fine sand) 17 Internal finishing- Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade including all scaffolding: New work (two or more coats ) over and including scrappingand priming coat with cement 18 P&F rigid PVC Pipe (IS:4985 mark) class II/(4KG./Cm2.) approved quality /mark including joining the pipe with solvent cement rubber ring and lubricant. 110mm dia 19 Wiring of light point/ fan point / exhaust fan point / call bell point as per PWD specification for electrical works with ISI marked 1.5sq. Mm nominal size FR PVC insulted unsheathed flexible copper conductor 1.1 kV grade (IS:694) and 1.5sq.mm nominal size FR/PVC insulted unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) in recessed ISI marked MMS (IS:9537 P-III) vergin material PVC conduit & Its all accessories (J.B. , Bends etc.) round tiles ,18 SWG Hot Dipped Galvanized Modular Box with earth terminal , 6A Modular switch , Modular face plate with grid plates, 3pin ceiling rose / lamp Holder / 3 pin connector , screws etc, making connections, all as per pre appoverd by Engineer in charge , testing etc. complete as required.For specification of copper conductor , PhenolicLaminated sheets & Electrical / Wiring accessories refer chapter E-04, E-05 & E-07. For additional technical parameter of product/work , referAnnexure A attached with this BSR.Long Point (up to 10mtr) 20 Wiring of 3/5 pin 6 amp. Light plug point as per PWD specification for electrical works with ISI marked 1.5 sq. mm nominal size FR/PVC insulated unsheathed flexible copper conductor 1.1 kV grade (IS:694) and 1.5 sq. mm nominal size FR/PVC insulated unsheathed flexible copper earth conductor1.1 kVgrade (IS:694) in recessed ISI marked MMS (IS:9537 P-III) vergin material PVC conduit & Its all accessories (J.B. , Bends etc.)round tiles ,18 SWG G.I. box with earth terminal of required size, 6A switch ,3/5 pin 6 A socket , 3.0 mm thick ISI marked PhenolicLaminated sheets(IS :2036-1995) , AI. alloy /cadmium plated iron screws 20mm cup washers etc. all as per pre approved by Engineer in charge, making connections, testing etc.complete as required.For specification of copper conductor , PhenolicLaminated sheets & Electrical / Wiring accessories refer chapter E-04, E-05 & E-07. For additional technical parameter of product/work , referAnnexure A attached with this BSR. On board 21 S&F following sizes (dia) of ISI marked MMS (IS:9537 P-III) vergin material PVC conduit as per PWD specification for electrical works along with its accessories (IS:3419) as required in recess including cutting the wall , covering conduit and making good the same as required. All relativeand latest acceptance tests reports by any NABL accredited lab for the conduit shall be submitted before execution & Engineer in charge. For additional technical parameter of product/work , referAnnexure A attached with this BSR.MMS (9537 P-111) PVC conduct. 25mm. 22 Supplying & Drawing FR PVC insulted unsheathed flexible copper conductor as per PWD specification for electrical works with ISI marked (IS:694) and as per IS 8130:2013 of 1.1 kV grade .Wire should be made from 99.99% purity copper , class 5 stranding in acc . to IEC 60228 for lower watt loss , oxygen free (<10ppm) for less chances of oxidization and higher silver contant for gives better conductivity ,insulation PVC type A , flame retardant as per IS 10810-53 , better amperage rating as per VDE0298 part 4, in exiting surface or reccessed PVC/MSconduit /casing capping including all as per pre approved by Engineer in charge, making connections etc.as required .OEM must have its own in house NABL lab setup for all testing facilities for wire .For additional technical parameter of product/work , referAnnexure A attached with this BSR. 2x1.5sqmm. 23 Supplying & Drawing FR PVC insulted unsheathed flexible copper conductor as per PWD specification for electrical works with ISI marked (IS:694) and as per IS 8130:2013 of 1.1 kV grade .Wire should be made from 99.99% purity copper , class 5 stranding in acc . to IEC 60228 for lower watt loss , oxygen free (<10ppm) for less chances of oxidization and higher silver contant for gives better conductivity ,insulation PVC type A , flame retardant as per IS 10810-53 , better amperage rating as per VDE0298 part 4, in exiting surface or reccessed PVC/MSconduit /casing capping including all as per pre approved by Engineer in charge, making connections etc.as required .OEM must have its own in house NABL lab setup for all testing facilities for wire .For additional technical parameter of product/work , referAnnexure A attached with this BSR. 2x2.5sqmm. 24 Providing & Fixing of IP20 SMD Mid Power LED batten type integrated light fixture made from polycarbonate /extruded aluminium powder coated housing with in built driver, Power Consumption of 18W/20W, system lumen efficacy ≥ 120 Im/Watt output, internal surge protection of 2.5 KV with Short & Open circuit protection, THD < 10% ,p.f.20.95, CRI >80, life time of minimum 50000 Burning Hours with, 70% of intial Lumen maintaned till life ends, CCT 3000°K/4000°K / 5700°K/6000°K/6500°K (As per ANSI Bin), maximum power consumption should not more than the specified rating and Fixture shall be of BIS standard and trade mark certificate (T.C.). Manufactures Word Mark/ Name Engraved/Embossing/ Screen printing on housing. 1170mm(+/-10%) LED batten with min. lumen output 2200 Im 25 Providing & Fixing of energy efficient /energy saving IP 20 LEDdirect retrofit Bulb in existing holder or fixture as required withsystem lumen efficacy ≥100 lm/Watt output,pf 0.95, CRI >70, minimum life time of minimum 25000 Burning Hours with, 70% of intial Lumen maintaned till life ends, CCT 3000°K/4000°K /5700°K/6000°K/6500°K (As per ANSI Bin), maximum power consumption should not more than the specified rating and Fixture shall be of BIS standard and trade mark certificate (T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) certificate / Report from OEM shall be submitted. All as per pre approved by engineer in charge. for additional technical parameters of product/ work, refer Annexure A attacheded with this BSR.6/7 Watt 26 Providing & Fixing of BEE Star rated copper wounded double ball bearing capacitor start, aluminium body & Metallic blade ceiling fan Conforming to all the performance requirements laid down in IS 374:2019 including all amendments, as applicable; & Carry BIS licensing (i.e. ISI marking) with down rod up to 80 cm with secondary support safety cable (steel rope), cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/work, refer Annexure A attached with this BSR.1200mm sweep BEE 2 star rated (Service value >=4.5 to <5) 27 P & F 1.2mm thick M.S. Recessed fan box, hexagonal/ round of size 130 mm dia, depth 75mm, 12 mm dia rod fan hook with 100 mm length extended on each side. All as per pre approved by Engineer in charge. For additional technical parameters of product 6.0/work refer Annexure A attached with this BSR 28 Providing & Fixing of modular type 120 W Step Fan regulator duly ISI marked (IS 11037:1984) with CM/L no. printed made out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tip with IP-20 rating, including all as per pre approved by Engineer in charge, making connections, testing etc. as required. For additional technical parameters of product / work refer Annexure A attached with this BSR55 step fan regulator 2 Module 360 dgree rotating
