Tender For Special Repair To Smq P 101 At Af Stn Kasauli Under Ge Kasauli; 2 Demolition ofcement concrete (reinforced) in Roofs, floors (other than ground floors), beams, staircases, landing, chajjas, and similar suspended workand removing rubbish/ demolished material outside defence land, complete all as specified and as directed . 3 Material and Labour for form work chulla hoods, chajjas, troughs and similar items including edges for fair finished surface of concrete, complete all as specified. 4 Material and Labour TMT steel bars of 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete, all as specified and as directed. 5 Material and labour for providing reinforced cement concrete 1:2:4 type B0 (using 12.5mm graded mechanically crushed stone aggregate)as chajja, fins, louvers, roof projection ,beam and lintel after removing of all loose concrete andloose plaster, cleaning surface with wire brush to remove all dust/dirt/loose particles to expose old steel reinforcement, applying derusting chemical on exposed steel surfacesuch as Dr fixit rust remover or equivalent and welding additional main bars/distribution bars by insertingto adequate depth in beam, chajjas, etc. complete, all as specified and as directed.Note- 1.The work will be carried out at a height upto 9 metre and necessary scafolding required in the work included in the quoted rate under this item.2.Reinforcement will measured and pid separately. 6 Material and labour rendering 5 mm thick on fair faces of brick work or concrete ceiling or chajjassurfaces in cement mortar 1:3 andfinishedeven and smooth without using extra cement and applyingtwo coats of cement based paint after preparation of newly plastered surfaces of ceiling complete all as specified and as directed.Note- 1.The work will be carried out at a height upto 8 metre and necessary scafolding required in the work included in the quoted rate under this item. 7 Taking down cement plaster of any description, thickness and in any position including raking out joints, hacking for key, scrubbing down with water etc , and removal the rubbish/ demolished material outside defence land, complete all as specified and as directed. 8 Material and labour for rendering 15 mm thick on surface of any description of brick work or concrete wall surfaces in cement mortar 1:4 mixed with water proofing compound @ 3% by weight of cement or as per manufacturers instruction and finished fair and even without using extra cement complete all as specified and as directed.( Note- The cost of providing WPC shall be included in quoted rate under this item). 9 Material andlabour for 10mm thick rendering in cement mortar (1:6)on surface of any description of brick or concrete and finished the surface even and smooth without using extra cement complete all as specified and as directed. 10 Material and labour for preparing new plastered or unplastered surfaces of walls and applying two coats of distemper oil emulsion, white or tinted over a coat of chalk whiteningcomplete all as specified and as directed. 11 Material and labour for preparation of new/old (plastered or unplasterd) surfaces of walls, applying 1 mm thick wall care putty white cement basedin two or more coats to achive smooth surfacesand applying two coats of exterior acrylic emulsion, anti weather abd anti algae paint (1st quality), in multi colour or as in(camouflage, if any) as approved, over and including a coat of alkali resistant primer, complete all as specified and directed.Note (s):-(i) Pattern of camouflage if any shall be as approved by GE.(ii)The work will be carried out at a height upto 8 metre and necessary scafolding required in the work included in the quoted rate under this item.(iii) Contractor shall carried out the painting work from the manufacturer of paint or his authorised applicators andalso submit 05 years gurantee certificate against fadding/Peeling of painting work to the department from manufacturer. 12 Material andlabour for complete removal of existing treatment on surfaces of walls by using appropriate technique as approved by Engr-in-chargefor complete removal of all layers of old treatment and reaching upto old plastered surface including filling up all cracks with Shalimar tar plastic (STP) crack filler and also, make good to plastered surface for the area n. exc. 0.01Square metre , if any and applying two coats ofoil bound distemperwith painting rollerover 1mm thick wall care putty white cement based in two or more coats to achive smooth surface over prepared surface complete all as specified and as directed. 13 Demolition of Brickwork or stone/ boulders masonry built in cement or cement lime mortar incl all quions, arches, pillars, etc but excluding ashlar facing, dressed stone work and precast concrete articles complete all as specified 14 Material and labourbrick work with sub class B old size bricks straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6 complete all as specified and as directed by the Engineer-in-Charge. 15 Supply andfixing for bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required, hooks (stay), heavy, for large gates, hook and pintle hinges, large hasps and staples, chains, hand made sliding bolts, clamps, hold fasts, wall ties, wind ties, hooks for hanging fans, plain angle cleats for securing purlins to wood trusses or rafters, knee piece inserts, two way and three way straps, plate washers and similar small articles conforming to Fe-290-Gde E-165, complete all as specified and as directed. 16 Supply and fixing 1mm thick and 100mm dia angles (internal or external) or nozzle pieces (Out lets) complete all as specified and as directed. 17 Material and labour for preparation of new steel surfaces of any description over 10cm in width or girth not other wise described and applying two coats of synthetic enamel paint over a coat ofred oxide primer complete all as specified and as directed. 18 Supply and fixing 110mm diaUPVC, rain water drain pipe, type ‘A’ ,conforming toIS 13592-1992, single socketed, in any length with rubber rings joints or jointed with solvent cement joint, fixed to wall, complete all as specified anddirected.(Note- Rubber rings for pipes and fittings shall be confirm to IS 5382-1985) 19 Supply and fixing 110 mm bore UPVC (SWR) plain bend any radius including jointing with solvent cement, complete all as specified.(Note- UPVCbends shall be confirm to BS 4515 DIN 19531 and DIN 19534) 20 Supply and fixing for 110mm diaUPVC, soil waste drain pipe, type ‘B’ ,conforming toIS 13592-1992, single socketed, in any length with rubber rings joints or jointed with solvent cement joint, laid in trenches or in floors, complete all as specified anddirected.(Note- Rubber rings for pipes and fittings shall be confirm to IS 5382-1985) 21 Supply and fixingin repair, 75mm diaUPVC, soil waste drain pipe, type ‘B’ ,conforming toIS 13592-1992, double socketed, in any length with rubber rings joints or jointed with solvent cement joint, fixed to wallincluding all fittings, heads, shoes, bends, swan necks, etc. complete all as specified anddirected.(Note- Rubber rings for pipes and fittings shall be confirm to IS 5382-1985) 22 Supply and fixing PVC (SWR) reducers complete all as specified and directed.(Note- UPVCbends shall be confirm to BS 4515 DIN 19531 and DIN 19534) 23 Taking down wooden chowkats or frames area exceeding 1.50 Square metre andnot exceeding 4.00 Square metre (w/o taking off shutters from frames) including iron mongries and removing from site, including cutting holes for taking out existing hold fasts and making good the disturbed portion of jambs andadjoining surfaces to match with existing finish, complete all as specified and as directed. 24 Taking down wooden chowkats or frames areanot exceeding 1.50 Square metre(w/o taking off shutters from frames) including iron mongries and removing from site, including cutting holes for taking out existing hold fastsand making good the disturbed portion of jambs andadjoining surfaces to match with existing finish, complete all as specified and as directed. 25 Supply and fixing aluminium power coating of approved colour (Thickness or powder coating not less than 50 micron) in frame for doors, windows, ventilator shutters, aluminium with one or more rebates including necessary joining cleats, rubber packing, powder coated snap beading, glazing clips to recieve 5.5 mm thick tinted glass for glazing section, etc. complete all as specified complete all as specified and directedNote : The weight of Aluminium sectons shall not be less than 1.20Kg/Rm. 26 Supplying, fabricating and fixing of powder coated aluminium Windows, Triple Track having three sliding shutters(02 Glass and 01 Guazed) with followingpowder coated aluminium section with and including joining cleats, glazing clips, rubber packaging, snap beading and other necessary builders hardware as required, complete all as specified and as directed.[a] Top and side members for three track frame shall be of size 92.00 x 31.75 x 1.5 mm [b] Three track bottom rail of frame for sliding of shutter shall be of size 92.00 x 31.75 x 1.5 mm [c] Top and bottom rail of sliding shutter shall be of size 40 x 18 x 1.55 mm [d] Side rail of sliding shutter with handle and self locking arrangement section shall be of size 40 x 18 x 1.55 mm [e] Sliding shutter to be provided with 5.5mm thick Tinted Glass.[f] One shutter to be provided with stainless steel wire cloth 0.36mm dia and aperture 1.4mmNote :- (i) The weight of Aluminium sectons shall not be less than 1.2Kg/Rm. (ii) Thickness or powder coating shall not be less than 50 micron (iii) The door/window shall be as per drawings/directions of Engineer-in-charge and drawing may be reffered from GE office.(iv) The cost of Glass and wire mesh shall be included in the quoted rate against this item. 27 Supplying, fabricating and fixing Aluminium Windows, fourTrack, fabricated with powder coated aluminium sections with four sliding shutters(03 Glass and 01 Gazed) with following section including joining cleats, glazing clips, rubber packaging, snap beading and other necessary builders hardware as required all as directed by Engineer incharge : (Length of window more than 1.5M)[a] Top and side members for three track frame shall be of size 92.00 x 31.75 x 1.5 mm [b] Three track bottom rail of frame for sliding of shutter shall be of size 92.00 x 31.75 x 1.5 mm [c] Top and bottom rail of sliding shutter shall be of size 40 x 18 x 1.55 mm [d] Side rail of sliding shutter with handle and self locking arrangement section shall be of size 40 x 18 x 1.55 mm [e] Sliding shutter to be provided with 5.5mm thick Tinted Glass.[f] One shutter to be provided with stainless steel wire cloth 0.36mm dia and aperture 1.4mmNote :- (i) The weight of Aluminium sectons shall not be less than 1.20Kg/R,(ii) Thickness or powder coating shall not be less than 50 micron (iii) The door/window shall be as per drawings/directions of Engineer-in-charge and drawing may be reffered from GE office.(iv) The cost of Glass and wire mesh shall be included in the quoted rate against this item. 28 Supply and fixing Aluminium Powder Coated [Powder coating shall be 50 micron minimum thickness) Sections as in window and ventilator Shutters, Side hung type, without Sash Bar,including necessary Joining Cleats, Glazing Clips, Rubber Packing, powder coated snap beading, Screws, Aluminium fittings such as Peg Stays 150mm Long [1 No], Hinges, Type B-21 100mm Long [2 Nos], Suitable Handle [1 No] to each shutter complete all as specified and directed.Note : The weight of Aluminium sectons shall not be less than 1.20Kg/Rm. 29 Supply and fixing 5.5 mm thick, tinted glass exceeding 0.5 Square metre in each pane to aluminium door/window with glazing clips, rubber gasket etc complete all as specified and as directed. 30 Supply and fixing figured glass 5.5mm thick, pin head type, in square exceeding 0.5 Square metre in each panefixed in aluminium frame as in windows/ventilators, complete all as specified and directed. 31 Supply and fixing stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed. 32 Supply andfixing aluminium anodized grill 5.5mm thick weight not less than 2.5kg per square (in the shape of expanded metal aluminium xpmjalli) opening size length of expansion (60mm) and width expansion 45mm fixed in aluminium anodized windowwith ‘F’ channel of handle section with screw, complete all as specified and directed. 33 Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs any thickness, including cover fillets complete all as specified and directed. 34 S&F,Metal suspended ceiling system OREO GI laid in plain 600X600X0.50 mm (tegular) edge tiles in global white colour to be laid on strong 24mm T-section flanges colour white having rotary stitching on the main runner with web height of 38mm. Note:(i) To comprise main runner spaced at 1200mm centres securely fixed to the structural soffit at 1200mm maximum centre.The first/last suspension system at the end of each main runner should not be greater than 450mm from the adjacent wall.Flush fitting 1200mm long cross tees to be interlocked between main runners at 600mm centre to form 1200x600 mm mould.Cut cross tees longer than 600mm require independent support. 600X600mm module to be formed by fitting 600mm long flush fitting cross tees centrally between the 1200mm cross tees.Perimeter trim to be wall angles of size 3000x19x19mm,secured to walls at 450mm maximum centres. (ii) Suspension system accessories consisting of HLC sleeve anchor fasterners of thread size 6.50 mmx25/5 with soffit cleat made of galvanised steel of size 27x37x25x1.60mm & level clip in dimensions of 85x30x0.80 mm with 4mm GI wire complete all as specified & directed.Note- Ceiling tiles and ceiling grid shall be of the same make. 35 Dismantling plain or corrugated mild steel sheeting any gauge, thickness, including Nanital or similar pattern roof coveringcomplete, all as specified and directed. 36 Supply and fixing of Pre-painted galvalume aluminuim zinc coating GI based corrugated steel sheet 0.50mm thick, conforming to IS-15961 of any colour having tensile strength of 550 MPa as in roof covering/cladding to wall, fixed with self tapping screws, complete, all as specified and as directed.Note- The sheets shall have (150 gm/sqm total on both sides) with super durable polyester quality paint of approved colour, suitable for exterior application conforming to IS-15965. 37 Supply and fixing ofPre-painted galvalume aluminuim zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 MPa as in roof covering/cladding to wall, fixed with self tapping screws, complete, all as specified and as directed.Note- The sheets shall have (150 gm/sqm total on both sides) with super durable polyester quality paint of approved colour, suitable for exterior application conforming to IS-15965. 38 Dismantling of wrought iron or mild steelwork of any description not otherwise specially providedcomplete all as specified and directed. 39 Supply andfixing mild steel, rolled sections as in main orcross beams, hip and jack rafters, purlin where connected to comman rafters and running rails and guides for sliding doors fixed with angle cleats or other connecting platesconforming to grade Fe-410(Gde 250), complete all as specified and directed. 40 Demolition of cement concrete of any description and in any position not otherwise specifically provided for including removal the rubbish/ demolished material outside defence land, complete all as specified and directed. 41 Material and labour for applying water proofing treatment to sunken slab comprising of the following specifications complete all as specified.(i)Cleaning of roof surface with mechanical means i.e. wire brush/air blower etc. andremove all loose /unsound material,dirt,dust etc, (ii) 15mm thick cement plaster on concrete surfaces in cement mortar (1:3) using and including water proofing compound @3% by weight of cementfinished even andsmooth without using extra cement,.(iii)Providing and laying water proofing treatment of sunken portion of WCs, bathroom etc by applying cement slurry @ 1.3 kg/sqm mixed with acrylic based polymer modified cementitous composit compound coating of make as approved in Technical Instruction 5/2003(iii)First layer of cement slurry @ 0.488 Kg/Sqmmixed with acrylic based polymer modifiedcementitious composite compound @ 0.253 Kg/Sqm of approved make and allowed layer to air cure for 04 hours.(iv)Second layer of cement slurry @ 0.244 Kg/Sqmmixed with acrylic based polymer modifiedcementitious composite compound @ 0.126 Kg/Sqmand allowed layer to air cure for 04 hours followed with water curing for 48 hrs .(v) 200 micron thick polythene film pasted with the hepl of adhesive shall be provided over treatment . 42 item No. 40.00(contd....)Note :-(i)The slope of slab shall be 1:20 towards the corner of outer walls and GI pipe of 40mm dia ( Medium grade ) be inserted at corner projecting out side 20 cm . (ii) Joints of WC/Trap/Soil waste shall be properly sealed with sealing compound(iii) P/S traps and Nahani/Floor traps with long arm shall be provided as per latest instruction .(iv) Testing of all trap & joint and sunken slab shall be as per IS-1742 before filling and tilling of sunken slabs, including smoke test. (v) The water proofing treatment shall be carried out by the manufacturer or his authorised applicators and contractor shall also provide 07 yearsGuranttee forwater proofing treatment carried out in the work. Testing of all traps and joint and sunken slab shall be done as per IS-1742 before filling and tiling work. 43 Material and labour for PCC 1:5:10 type E-2, using 40 mm graded crushed stone aggregate as in filling in sunken floor, rounded or chamfered on edges complete all as specified and directed . 44 Supply only integral water proofing compound complete all as specified.as directed . 45 Supply and fixing vitreous china wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern)including plastic water closet seat white closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinges device and brass chromium plated Jet spray with PVC pipe andcomplete accessories as in repair, complete all as specified and as directed. 46 Supplyand fixing (in repair) brass chromium plated jet sprayer suitable for water closet pedestal pattern including 90cm long Chromium plated flexible pipe fixed to angle valve 15mm bore, complete all as specified and directed . 47 Supply and fixing 75mm dia of outlet, PVC (SWR) floor trap plain with grating including jointing with solvent cement, complete all as specified.(Note- UPVCfittings shall be conforming to BS 4515 DIN 19531 and DIN 19534) 48 Material and labour for 25mm thick PCC 1:2:4 type B-0 using 12.5mm graded stone aggregate as levelling course, finished even and fair to receive floor finishes, complete all as specified and directed. Note- This item shall not be executed in the location, where dismantling of tiles work have been done. 49 Supply and fixing 40 mm dia GI pipe , medium grade as in spout for sunken floor, fixed as in wall inside end fixed with wire netting and external bevelled edge at 45 degree, complete allas specified and directed. 50 Demolition ofcement concrete in ground floor and pavings not exceeding 15cm thickness (below or above ground level) and removal the rubbish/ demolished material outside defence land, complete all as specified and directed. 51 Material and labour providing 75 mm thick cement concrete 1:3:6 type C-2 using 40mm graded crushed stone aggregates as in plinth protection laid in alternatebays (not exc 2 Sqm each )and finished even and smooth without using extra cement and providing jointsthroughout the thickness of the plinth protection filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight including form work complete all as specified and as directed. 52 Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed. 53 Material and labour for screed bed or bedding layer of mortar, 15 mm thick for laying floor finishes in cement mortar 1:4 complete all as specified and as directed. 54 Material andlabour for premium quality, joint free, non skid, coloured ceramic 7 to 8mm thick (square/rectangular) area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm tiles, as in floor, set and jointed in neat cement slurry @ 3.00 kg/square metre and pointed in white or coloured cement to match the surface over cement screed bed , complete all as specified and as directed. 55 Material and labour for glazed ceramic coloured/printed tiles 450mm x 350mm x 6 to 7mm thick on vertical surfaces as in skirting, dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile, laid over and including 10mm thick bedding layer in cement mortar (1:3), complete all as specified and directed. 56 Material andlabour for 2nd class hard wood plain, solid straight chowkats and frames, wrought framed rebated on the solid, rounded or chamfered put together with glue pinned at joints complete, all as specified and directed. 57 Material and labour for 18/19mm thick pre laminated particle board, exterior grade, pre-laminated one side with decorative choice lamination and other side balancing white lamination with 1st class hard wood 5mm thick teak wood edging all around, fixed with screws to timber framework and leaping treated with french polish suitable for cup board shutters, palmet box, etc.complete all as specified and as directed. 58 Supply and fixing, extruded aluminium alloy handles with plates, fabricated type, anodised 75mm size, ISI marked, complete all as specified and directed . 59 Supply and fixing in repairHarrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc. 25 mm dia with brackets etc complete all as specified and directed . 60 Dismantling water tanks of capacity exc. 250 ltr and not exc. 500 ltrs and removing from site complete all as specified and as directed. 61 Supply and fixing water storage tank 500 ltr capacity HDPE triple layer, confirming to ISstandard, fixed andhoisted in position on staging or roof complete with locking arrangement including provn of over flow pipe, air lock pipe, brass valve high pressure with polythene float and flynut , ISI marked, screwed and suitable for iron pipe 20 mm bore, complete all as specified and directed 62 Taking up or down steel tubing and connections for 15mm dia including cleaning for refixing or removal to store complete all as specified and directed . 63 Supply and fixing of 15mm dia tubes, medium grade, galvanized, ISI Marked, with all fittings such as sockets, bends, elbows, tees etc, fixed to walls and ceiling or laid in floors, including cutting existing steel tubing and screwing, if required for alterations and additions, complete all as specified and directed. 64 Refixingsteel water tubing of 15 mm bore in new or old position withall new fittings as required, laids in floor , wall and on ceiling, complete all as specifiedand directed. 65 Taking up or down steel tubing and connections for 20mm dia including cleaning for refixing or removal to store complete all as specified and directed . 66 Supply and fixing of 20mm dia tubes, medium grade, galvanized, ISI Marked, with all fittings such as sockets, bends, elbows, tees etc, fixed to walls and ceiling or laid in floors, including cutting existing steel tubing and screwing, if required for alterations and additions, complete all as specified and directed. 67 Refixingsteel water tubing of 20 mm bore in new or old position withall new fittings as required, laids in floor , wall and on ceiling, complete all as specifiedand directed. 68 Taking down shutters of any description but not exceeding 1.00 Sq.m eachfrom chowkhat and removing from site complete all as specified. 69 Taking down shutters of any description exceeding 1.00 Sq.m but not exceeding 2.00 Sq.m each, from chowkhat and removing from site complete all as specified. 70 Material and Labour for plain cement concrete 1:3:6 type C-1 (using 20 mm graded mechanically crushed stone aggregates) as in fixing of hold fasts, copings, bed plates,kerbs or mud stops,lintels upto 1.50m span, plinth courses , seismic and other bands and the like, finished the surface fair andeven, including necessary form work complete all as specified and directed. Note- If reinforced concrete, reinforcement shall be measured and paid for separately. 71 Supplyand fixing factory made flush shutters 30 mm thick, solid core construction, with block board core and plywood face panels, commercial type on both sides, ISI marked complete all as specified. 72 Supply and fixing 35 mm thick, 2nd class hard wood, partly or fully glazed and skelton shutter open rebatedand prepared to receive glass ,gauge etcdivided into squares with plain, chamfered or rounded, mitred beads, rebated sash bars any numbers for securing glass, etc or partly with panels of 9mm BWP commercial ply etc with size of members of shutters as specified in SSR Part-I, section 8 clause 8.24(a) or to match with existing shutters etc complete all as specified and as directed. 73 Suppling and fixing solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet, reinforced with M.S. square tube and fixing in opening as per specification complete all as specified and as directed. 74 Suppling and fixing Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M. S. tubes for top & bottom rails. M. S. frame shall be covered with heat moulded plain colour PVC `C` channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side & as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the M. S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement,fixing in the frame as per specification complete all as specified and as directed. 75 Taking down existing earthing continuity conductor, aluminium strip 25X3.15 mm ,and removing to store for keeping safe custody for refixing and makinggood to surface complete all as specified anddirected . 76 Taking down existingAir termination single pointed aluminuim Rod 12 mm dia 300 mm longremoving to store for keeping safe custody for refixing and refixing the same after completion of civil work complete all as specified anddirected . 77 Refixing of earthing continuity conductor aluminium strip 25 X 3.15 mm with saddles and screw, etc.drawn through conduit in trenches / under floor /on wall or on roof including insulator complete all as specified anddirected . 78 Supply andfixing mild steel butt hinge of 100mm length, cold rolled, medium weight, ISI marked complete all as specified and directed. 79 Supply and fixing mild steel, semi-barrel tower bolt 200 mm , open cover, with sheet pressed barrel, stove enamelled black with bright bolt complete all as specified and as directed. 80 Material and labour for preparing new or previously untreated wood and wood based surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified anddirected . 81 Material and labour for preparation of old surface of wood and wood based materials over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified anddirected . . 82 Material and labour for preparation of old steel surface of any description not otherwise described, over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed by the Engineer-in-Charge. 83 Dismantling of cast iron or reinforced concrete drain pipes of any size, jointed in cement mortar and taking out of trenches or from any position, complete all as specified and as directed. 84 Supply and fixing in repair, cast iron soil, waste and vent spun pipes 75 mm bore, ISI marked, in any length, with or without ears, with cement joints, laid in trenches or in floors complete, all as specified and directed. 85 Supply and fixing in repair, cast iron soil, waste and vent spun pipes 75 mm bore, ISI marked, in any length, with or without ears, with cement joints, fixed to wallcomplete, all as specified and directed. 86 Supply and fixing in repair, cast iron soil, waste and vent spun pipes 75 mm bore, ISI marked, in any length, with or without ears, with cement joints, laid in trenches or in floors complete, all as specified and directed. 87 Supply and fixing in repair, cast iron soil, waste and vent spun pipes 75 mm bore, ISI marked, in any length, with or without ears, with cement joints, fixed to wallcomplete, all as specified and directed. 88 Supply and fixing cast iron branch pieces, 100 mm dia, single (equal or unequal), ordinary or inverted(spigot or socket type) or with parallel branches complete, all as specified and directed. 89 Supply and fixing cast iron bends (any radius) 100 mm dia diminishing pieces or tapers complete, all as specified and directed. 90 Supply and fixing cast iron bends (any radius) 75mm dia diminishing pieces or tapers complete, all as specified and directed. 91 Supply and fixing cast iron branch pieces, 75 mm dia, single (equal or unequal), ordinary or inverted(spigot or socket type) or with parallel branches complete, all as specified and directed. 92 Supply and fixing vitreous china wash hand basin, white , flat back of size 550mmx400mmfixed on and including cast iron cantilever bracket, 32mm dia brass waste coupling chromium plated and 32 mm dia PVC waste pipe including fixing ofwaste fitting, etc. as in repair complete all as specified and as directed. 93 Supply and fixing in repair,15mm bore pillar tap, chromium plated, cast copper alloy with capstan head, screwed down, high pressure, with or without lettered ‘Hot’ or ‘Cold’ complete all as specified and directed. Make--PRIMA Cat No PPL-5309 or equivalent model in makes mentioned in Appendix B of tender document.Note- Contractor shall submit a guarantee certificate from manufacturer to Engineer-in-Charge before claiming payment. 94 Supply and fixing in repair, stop valves, 15 mm dia pipe, chromium plated, fancy type, ISI marked, screwed down, high pressure with capstain head, (concealed type) with sliding flange, screwed both ends for 15mm bore pipes or for unions complete all as specified and directed.Make- PRIMA Cat NoPLF-6210or equivalent model in makes mentioned in Appendix B of tender document.Note- Contractor shall submit a guarantee certificate from manufacturer to Engineer-in-Charge before claiming payment. 95 Supply and fixing in repair, bib tap, long body, screwed down, high pressure, cast copper alloy, fancy type, chromium plated, ISI marked, with capstan heads, screwed down suitable for 15mm bore pipe or union complete all as specified and directed.Make- PRIMA Cat No PLF-6202 or equivalent model in makes mentioned in Appendix B of tender document.Note- Contractor shall submit a guarantee certificate from manufacturer to Engineer-in-Charge before claiming payment. 96 Taking down bib tap, of any description removing to store for keeping safe custody for refixing and refixing the same complete all as specified anddirected . 97 Supply and fixing PVC connections 45cm long and 15mm dia with PTMT nuts and PVC washers on both ends, complete all as specified anddirected . 98 Excavating in trenches, not exceeding 1.50 metre wide and not exceeding 1.50m in depth for foundation etc. or for shafts, wells, cesspits, manholes, pier holes etc. not exceeding 10 sq.m on plan and not exceeding 1.50m in depth and getting out in hard/dense soil complete, all as specified and as directed. 99 Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick in soil of any description, complete all as specified and as directed. 100 Removing excavated soil to a distance not exceeding 50 metre and deposited where directed at a level not exceeding 1.5m above the starting point, complete all as specified and as directed. 101 Demolition of SGSW drain pipe of any bore jointed in cement mortar including PCC bedding/hunching, and taking out of trenches with fittings complete all as specified and as directed. 102 Material and labour for concrete bed to drain pipes of 110mm dia including packing under and hanging against the sides of pipes after they are laid and tested in cement concrete 1:4:8 type-D2 using 40mm graded mechanically crushed stone aggregate , complete all as specifiedand directed . 103 Supply andfixing in repair, for 2mm thick fibre glass reinforced translucent corrugated sheeting with two corrugation side lap fixed with L type or J type or cranked hook bolt in roof, wall etc. complete all as specified and as directed 104 Supply and fixing in repair 10 ltr PVC valveless syphonic action type flushing cistern with brackets, flush pipe etc complete including inlet ball valve float and handle including brackets, of approved make including all connections & flush pipes for WC complete all as specified and as directed. 105 Taking down copper/ aluminium point wiring(light, fan, socket or power) complete, including fittings and fixtures such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc removing materials to store for keeping in safe custody or for taking credit (fittings such as switches, sockets, ceiling rose, pendent holders, light fittings etc. are to be measured separately) and making good distrubed surfaces of wall, floors, etc. complete all as specified and directed. 106 Material and labour for Point wiring with 1.50 Sqmm single core PVC insulated , unsheathed cable flame retardant low smoke and low halogen FRLSH, 1100 volt grade for phase (red) and neutral (black), with multi stranded copper conductor drawn through and incuding medium grade, ISI marked, PVC conduit not less than 20 mm dia with accessories, concealed on wall/ceilingand incuding provision of 1.50 Sqmm single core PVC insulated , unsheathed cable flame retardant low smoke and low halogen FRLSH, 1100 volt grade with multi stranded copper conductorgreen colour as earth continuity conductor and connected to common earth dolly with suitable size of lugs, including mild steel sunken box or pressed steel terminal boxes made out of not less1.2 mm thick mild steel sheet metal conforming to IS with earth dolly and coated with two coats of anti corrosive paint over a coat of red oxide primer bothinternally and externally including provision of new 3 mm thick plastic laminated sheet top cover extended up to 25 mm over sunken box for housing the switches , socket outlets, fan regulators etc. with brass screws and brass washersand making goodthe disturbed surfaces as per existing for one ligh point controlled by one switch one way switch 6 Amp. Note :- Switch, socket and fan regulators to be measured and paid for separately . PVC Conduit confirming to IS 9537 part I & III. Note:- (All chases will be cut by chase cutter only). 107 Description all as per Srl item No.105 here in before but one ceiling fan/ exhaust fan point controlled by one way switch 5 Amp complete all as specified and as directed.. 108 Description all as per Srl item No.105 here in before but one bell point controlled by one bell push button complete all as specified and as directed.. 109 Description all as per Srl item No.105 here in before but one switch socket outlet 3 pin, 5 Amp on same board complete all as specified and as directed. 110 Description all as per Srl item No.105 here in before but one switch socket outlet 3 pin, 5 Amp on the independent board complete all as specified and as directed. 111 Description all as per Srl item No.105 here in before but one light point controlled by two way switch 5 Amp complete all as specified and as directed. 112 Description all as per Srl item No.105 here in before but 2.5 sqmm single core multi stranded copper conductor PVC insulated unsheathed(FRLSH) cable 1100 voltsincuding 2.5 sqmm stranded copper conductor (FRLSH) PVC insulated green in colour as continous earth conductor connected to common earth and earth dolly with all accessories for one 5 pin 16 Amp socket (Power point) on independent board complete all as specified and directed. 113 Description all as per Srl item No.105 here in before but 4.0 sqmm single core multi stranded copper conductor PVC insulated unsheathed(FRLSH) cable 1100 voltsincuding 4.0 sqmm stranded copper conductor (FRLSH) PVC insulated green in colour as continous earth conductor connected to common earth and earth dolly with all accessories for one 5 pin 16 Amp socket (Power point) on independent board complete all as specified and directed. 114 Supply and fixing switch piano 6 Amps, flush type, single pole, one way,230 volt , AC supply,ISI Marked, complete all as specified and directed. 115 Supply and fixing switch piano 16 Amps, flush type, single pole, one way,230 volt , AC supply,ISI Marked, complete all as specified and directed. 116 Supply and fixing switch piano 6 Amps, flush type, single pole, one way,230 volt , AC supply,ISI Marked, complete all as specified and directed. 117 Supply and fixing switch piano 16 Amps, flush type, single pole, one way,230 volt , AC supply,ISI Marked, complete all as specified and directed. 118 Supply and fixingswitch piano, bell push, 6 Amps, flush type, 230V, 50 Hz supply, complete all as specified and directed. 119 Supply and fixing switch piano 6 Amps, flush type, single pole, two way,230 volt , AC supply,ISI Marked, complete all as specified and directed. 120 Supply and fixing PVC power unit modular box (DBOXx) with MCB protected socket with plug top of 25 Amp complete all as specified and directed. 121 Supply and fixingfan regulator electronic step type(Socket type), 120 watt, 230 Volts, 50 Hz, AC supply suitable for ceiling fan any type/make/sweep complete all as specified. 122 Supply and fixing ceiling rose surface bakelite 65x50mm, type 2/3 terminal, isolated body complete all as specified and directed. 123 Supply and fixing for Bell, electric,Ding Dong type, AC, 230 volts, single pole complete all as specified and directed. 124 Supply and fixing lamp holder, PVC/polycarbonate angular type with back plate, complete all as specified and as directed. 125 Supply and fixing in replacement,LED lamp, 5 watt,threaded/pin end, warm/cool lamp type suitable for fixing onbatten/angular holders completeall as specified and directed. 126 Supply and fixingin replacement, LED lamp, 12 watt,threaded/pin end, warm/cool lamp type suitable for fixing onbatten/angular holders completeall as specified and directed. 127 Taking down carefully old unserviceable MCBs DBs any type including MCB SP/SPNand removing to store for keeping safe custody for taking credit and makinggood to surface completeall as specified and directed. 128 Supply and fixing sheet metal enclosures for distribution boardTPN, 4 ways, double door, 415 volts, with and including 200 amps rated bus bar, vertical type, with MCCB as incomer andMCBs as out going, conforms to IS:8623.III, IP:43 protection and making all type of connections with suitable size of gland for incomer LT cable complete , concealed on the wall surface, making good the disturbed portion withadjoining surfaces to match with existing finish complete all as specified and as directed. 129 Supply and fixing factory made sheet metal MCB distribution board, 12 way with 200 Amps rated bus bar, single pole and neutral withdouble door IP-42 fixed on wall duly grouted in wall or on wooden board in and including copper lugs/thimbles duly crimped for connection, including making smooth the disturbed surfaces complete all as specified and as directed 130 Supply and fixing in replacement, MCCB 125A, 4 pole, 415 volts withbreaking capacity 16 kA and conforms to IEC 60947-2, complete all as specified & directed. 131 Supply and fixingin replacement, MCB,Single Pole and neutral, AC supply, 240 volts, 40-63 Amps,C series,10 kA rupturing capacityand making connections complete all as specified and as directed. 132 Supply and fixing in replacement, MCB,Single Pole, AC supply, 240 volts,06 to 32 Amps,C series,10 kA rupturing capacityand making connections complete all as specified and as directed. 133 Supply and fixing in replacement LED tube light batten fitting 20W (single side connection) including LED rod including all accessories internally pre-wired and including connecting up with three core twisted flexible copper conductor cable with suitable size complete all as specified and directed. 134 Supply and fixing in replcementLED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. 135 Supply and fixing in replacementLED surface mounted bulk head luminaries 10 watt with min 800 lumen, industrial model, IP 65, PVC housing, surge protection including driver & LED lamp, etc. complete with all accessories, connecting with copper conductor flexible cablefrom ceiling rose to connector of the light , complete all as specified and as directed. 136 Supply and fixing in replacement LED light fitting 25 W outdoor type for new generation energy saving and environmental friendally long life LED building security light made up of pressure die cast aluminium housing with high efficiency LED as lighting source and lens embedded PC cover having bottom opening seperate driver compartment with IP66 protection and impact resistance of IK08 complete all specified and directed.Note : The quoted rateinclude the provn of PVC flexible pipewhere connection wire providedfor light fittings, ceiling fan/ exhaust fan, etc. 137 Disconnecting and taking downceiling fans with blades, exhast fans, metallic body of any make and model andfrom its locations and kept in safe custody and refixing the same in the same location or in other location after completion of complete wiring and civil works including spray painting the steel surface with synthetic enamel paint by spray gun machine complete all as specified and directed.Note : (i) Flexible PVC insulated multistranded copper conductor single core two runs from ceiling rose to fan is inclusive in the quoted rate. 138 Disconnecting of exhast fans (air circulators) PVC body of any make and model and taking down from its locations and kept in safe custody and refixing the same in the same location or in other location, after completion of complete wiring and civil work including cleaning the same before fixing complete all as specified and directed. 139 Disconnecting and taking down of serviceable geysers of any description, capacity and make with its accessories from its locations and kept in safe custody and refixing the same in the same location or in other location, after completion of complete wiring and civil work including cleaning the same before fixing complete all as specified and directed. 140 Supply and fixing in replacement of exhaust fan metallic body 300mm sweep, AC, 230V, single phase, 50 Hz complete all as specified and directed.Make-Standard, model-FSVRASTGRY12 or equivalent make/model mentioned in Appendix B of CA complete all as specified and directed. 141 Supply and fix in replacement of air circulators fan (exhaust fan) PVC body for fresh air having 200mm sweep AC, 230V, single phase, 50 Hz, complete all as specified and directed. Make-Standard, model-FSVRFDXOWH08 or equivalent make/model mentioned in Appendix B of CA complete all as specified and directed. 142 Material and labour for GI bracket, medium grade, 40mm dia, 1.20 m length bent to required length, fixed to wall with two clamps made of 20 x 3 mm mild steel flat minimum 15cm long, 4 nos 8mm dia bolts with nuts with two coats of synthetic enamel paint over one coat of red oxide paint complete all as specified and directed. 143 Taking down carefully unserviceable sub main wiring of any size and type, removing material from site for taking credit and making good the disturbed surfaces of walls, ceilings etc including existing PVC/Steel conduit/ casing caping etc and removing materials from sites and making good distrubed surface of walls and roofs complete all as specified and as directed. 144 Material and labour for sub-main wiringwithsingle core PVC insulated sheathed 1100 volt grade multi stranded FRLSH Copper conductor cable of size 6.0 sqmm (Nominal area) drawn through in and including PVC concealed conduit of required size not less than 25mm dia with all fittings and accessories alongwith one single core green colour PVC insulated sheathed 1100 volt grade multi stranded FRLSH Copper conductor cable of size 4.0 sqmm as earth lead and connected to earth dolly and making good to disturbed surfaces etc, all as specified and directed. Note :-(i) Cutting/ Chasing of wall/ stair case etc. deemed to be included in the quoted rates of this item. (ii) Thimble/lugs of rating of MCB should be used with wire for fixing in the MCB.(iii) Three runs of cable and one run of PVC conduit shall be measured and paid as one unit length. 145 Disconnecting of old earthing and replacement with galvanised steel earth electrode plate of size 600x600x6mm thick, buried directly in ground (earth pit not less than 2.25m deep below normal ground level) with top edge of the plate not less than 1.50m below normal ground level, connected to galvanised iron earth lead 4mm wire upto test point with suitable GI nuts/bolts and brazed properly up to main board including earth pit in cement concrete 1:2:4 type B-1,precast RCC cover in 1:2:4 reinforced with expanded metal, with suitable handle, excavation and earth work in any type of soil and including medium grade GI watering pipe 20mm bore with funnel wire mesh and light grade GI wire protection pipe 15mm bore up to main board complete as shown in electrical plate No. 3 of MES schedule Part-I 2009, connected to earthing testing point including taking out existing unserviceable earthing complete all as specified and testing on completion complete all as specified and directed.Note - The units rate includes the cost of excavation & earth work in any type of soil, charcoal & salt in alternate layers, 20mm GI pipe (medium grade) for watering 15mm GI pipe for protection of wire (light grade) funnel wire mesh PCC chamber in PCC 1:3:6 type C-1 cast iron frame and 40mm thick RCC cover for pit etc & no extra payment will be made. 146 Amount of credit of Rs. 45622.00for retrived old material as mentioned in Schedule A section-II of tender document in pdf form, will be deducted offline while acceptence of tender.
