Tender For Special Repair To Building No P 7 At Jak Li Rc Srinagar Under Ge 970 Ews.; 1 Demolition of brick work built in cement mortar including all quoins, pillars etc but excluding ashlar facings, dressed stone work and precast concrete articles complete all as specified and directed. 2 M&Lbrick work with sub class `B’ bricks, straight or curved on plan exceeding 6m mean radius built in CM 1:6 complete all as specified and directed. 3 Description all as per item No-2 here-in-bfore but except bricks complete all as specified and directed. 4 M&Lbrick work with sub class `B’ bricks, straight or curved on plan to any radius in half brick thick walls, built in CM 1:4 complete all as specified and directed. 5 Demolition of cement concrete in ground floors and pavings not exceeding 15cm thickness (below or above ground level) complete all as specified and directed. 6 Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition) complete all as specified and directed. 7 Formwork as in flat and fair finish surfaces to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200m thick (Horizontal or sloping) complete all as specified and directed. 8 M&L RCC Type B1 1:2:4 (using 20mm graded crushed stone aggregate) for slabs supported on walls,beams and columns in floors,roofs, landings, balconies,canopies, deck slabs and in shelves and the like complete all as specified and directed. 9 M&L precast reinforced cement concrete 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in cover slabs (for manholes etc), shelves and similar articles with plain faces including necessary moulds and setting in cement mortar 1:6 including necessary form work complete all as specified and directed. (reinforcement to be measured separately) 10 TMT steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire annealed not less than 0.9mm dia or securing with clips, complete all as specified and directed. 11 M&L 100mm thick PCC (1:4:8) type D-2 (using 40mm graded crushed stone aggregate)as in sub base to flooring finished even and roughcomplete all as specified and directed. 12 M&L25mm thick PCC 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregate) as in level course with finishing in cement concrete surface even and rough to receive screed bed complete all as specified and directed. 13 Dismantling floor, hearth, wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed. 14 Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc. complete all as specified and directed. 15 M&L20mm thick Granite (of any type)work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including screed bed of 15mm thick 1:6complete all as specified and directed. 16 M&LMarble work 20mm thick (table rubbed and polished) in steps, jambs, pillars, windowcills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade incl rounding off edges and bull noosing of all external edgesover and including screed bed of 20 mm thick 1:3 and pointed in white or coloured cement to match complete all as specified and directed. 17 M&Lrounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed. 18 M&L Joint free Non - skid coloured ceramic tiles not less than 8mm thick (square/rectangular) area of each tile exceeding 0.18sqm but not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry over screed bed of 15mm thick in CM 1:6 and pointed in white or coloured cement to match complete all as specified and as directed 19 M&L Joint free Non - skid coloured ceramic tiles not less than 8mm thick (square/rectangular) area of each tile exceeding 0.18sqm but not exceeding 0.36sqm in skirting/dado or vertical surfaces with back coat of screed bed or bedding layer of 10mm thick in CM 1:4 and pointed in white or coloured cement to match complete all as specified and directed. 20 M&L Joint free Non - skid coloured ceramic tiles not less than 8mm thick (square/rectangular) area of each tile exceeding 0.11sqm but not exceeding 0.18sqm, in floors etc. set and jointed in neat cement slurry over screed bed of 15mm thick in CM 1:6 and pointed in white or coloured cement to match complete all as specified and directed. 21 M&L Glazed coloured ceramic tiles in verticle surfaces 450 x 300 x 7mm thickset and jointed in neat cement slurry and pointed in coloured cement to match with backcoat of screed bed or bedding layer 10mm thick in CM 1:4 and pointed in white or coloured cement to match complete all as specified and directed. 22 S&F selected quality looking mirror bevelled edge 5.5mm thick selected quality glass, mounted on 6mm thick commercial plywood, including moulding of all round edges of looking mirror and fixed to wooden plug with appropriate nos CP brass screwed cup washers complete all as specified and directed. 23 M&L 75mm thick PCC (1:4:8) type D-2 (using 40mm graded crushed stone aggregate) as in sub base to flooring finished even and roughcomplete all as specified and directed. 24 M&Lpremium external paving tiles of techno commercial or equivalent of size 40cm x 40cm x 10 mm thick, set, jointed and pointed in neat cement slurry in floors, laid over 15 mm thick bedding layer in Cement Mortar 1:6 complete all as specified and directed. 25 M&Lcutting chases, pinning in, making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades shelves, lintels etc, and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting not exc 10cm girth complete all as specified and directed. 26 Taking up or down GI Water Tubing 15mm dia (bore) including Connections and Fittings, segregating serviceable Pipes & Fittings and Stacking properly at Site(s) for re-use, complete all as specified and directed. 27 Description all as per Item No. 26 here–in–before, but for 20mm dia (Bore) complete all as specified and directed. 28 M&L 20mm outer diameter of pipes (Inner dia 14.40mm) 3-layer PP-R (Polypropylene random copolymer) concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot and cold water supply including all PP-R plain and brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc. complete all as specified and directed. 29 Description all as per Item No. 28 here–in–before, but for 25mm outer diameter of pipes (Inner dia 18.0mm), complete all as specified and directed. 30 Taking up or down and refixing old PP-R pipe20mm dia and connections in new or old position (Walls, ceiling, floors, etc.) complete all as specified and as directed. 31 M&L Lagging to pipes used in internal water supply (internal dia of pipe 20mm) or plumbing all round with,25min thick bonded mineral wool preformed ‘SNAP ON’ pipe sections of density 144 Kg/cum conforming to IS 9842 complete all as specified and directed. 32 S&F 20mm dia PP-R Gate valves (brass insert) as per requirement of the site complete all as specified and directed. 33 S&F in repairs vitreous China squatting pan, Orissa pattern including PVC trap, size 580 x 440 mm white, with integral foot rests squatt pattern closet also includes setting the trap and pan in cement concrete (1 cement, 2 sand or surkhi and 5 aggretate), min. 150mm thick all round and finished just below level of rim of pan to receive the floor finishing (thickness as indicated) and making good floor complete all as specified incl cutting to the flush pipe and necessary repair to the floor complete all as specified and directed. 34 S&F in repairs PVC Flushing Cistern 10 litres capacity, Low Level Valve Less, Syphonic Action type, White, with Inlet, Ball Valve, Float and Handle including 32mm dia PVC Flush Pipe, a Pair of MS Brackets,CP flush bend including Cutting and Pinning in Ends, Making Good Disturbed Surfaces in Cement Mortar 1:3, complete all as specified and directed. 35 S&F in repairs vitreous china wash hand basin with pedestal, white, flat back, size 550mm x 400mm, including brackets,PVC waste pipe 32mm dia,wastecoupling brass, chromium plated and including cutting for and pinning in ends of brackets or erecting stand, complete all as specified and directed. 36 S&F in repairs brass Chromium plated Basin Mixer 15mm valve hot and cold screwed down for iron pipe complete all as specified and directed. 37 S&F in repairs Brass CP Wall mixer for mixing hot and cold water (3 in 1)screwed down for iron pipe and fixed bore of pipe 15mmcomplete all as specified and directed. 38 S&F in repairs 15mm dia bib taps fancy type CP Brass with Capstan head, screweddown, screwed for iron pipe of bore 15mm complete all as specified and directed. 39 S&F in repairs Angle Cock,15mm fancy type, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed. 40 S&F PVC Connections 15mm size with PTMT Nuts of length 600mm and fixed, complete all as specified anddirected. 41 S&F in repairs Brass CP Sink Mixer with regular spout for mixing hot and cold water screwed down for iron pipe and fixed bore of pipe 15mm complete all as specified and directed. 42 S&F in repairs Brass chromium platedshower rose 125mm size with 225mm Flange, swivel joints, including fixing to steel pipe or unioncomplete all as specified and directed. 43 S&F in repairs Tubular towel Rail CP Brass, chromium plated D type with CP Brackets, 600 mm long between flanges complete all as specified and directed. 44 S&F in repairs Glass shelf 450 x 125 x 6MM (with ABS Bracket chromium platedbracket guard and SS railing complete all as specified and directed. 45 S&F Soap Dish Stainless Steel of appropriate size complete all as specified and directed. 46 S&F Peg Set of 6 Stainless Steel as approved by GE complete all as specified and directed. 47 S&F Corner Glass Shelf 300mm (with ABS Brackets) 300 x 300mmas approved by GE complete all as specified and directed. 48 S&F Towel Ring including necessary stain less steel screws, rawl plugs and washers complete all as specified and directed. 49 S&F in repairs stainless steel plate rack of stain less steelsheet 1.00mm thick of size size 24 x 30 x 10 inch of best quality including necessary stain less steel screws, rawl plugs and washerscomplete all as specified and directed. 50 S&F sinks without drain board made of stainless steel 1.00mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and directed. 51 Demolition and taking out cement mortar or lime concrete, brick bats from sunken floor portion complete all as specified and directed. 52 M&Lpreparing surface of sunken slab and applying 15mm thick cement plaster 1:3 cement sand mortar with integral water proofing compound both on floor and wall.The surface shall then be cured and allowed to dry then applying Epoxy Resin coating Polymer modified cementation coating like brush bond of Fosroc, Pidilite or Bostic as per manufacturers instructions both on floor as well as on wall and sunken floor shall be filled with graded cinder concrete upto top level to receive top flooring, incl providing 25mm dia GI spout pipe projecting 0.25mtr beyond the external face of wall complete all as specified and directed. 53 M&L40mm thick PCC 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregate) as in Sunken Portion of WC/Bath roomcomplete all as specifed and directed. 54 M&Llime conrete with lime mortar 1:5:10 mix (using 40mm graded brick coarse aggregate) in sunken Portion of WC/bath room complete all as specified and directed. 55 Dismantling of PVC / CI pipe 100mm dia jointed in cement mortar and taking out of trench if required complete all as specified and directed. 56 Dismantling of PVC / CI pipe 75mm dia or less jointed in cement mortar and taking out of trench if required complete all as specified and directed. 57 S&F 75mm bore PVC (SWR) Soil, waste and vent pipes single socketed in any length with rubber ring joints fixed to walls and making good with cement mortar 1:3 or with PCC 1:2:4 complete all as specified and directed. 58 S&F 75mm bore PVC (SWR) Soil, waste and vent pipes single socketed in any length with rubber ring joints laid in trenches or in floors and making good with cement mortar 1:3 or with PCC 1:2:4 complete all as specified and directed. 59 S&F 110mm bore PVC (SWR) Soil, waste and vent pipes single socketed in any length with rubber ring joints fixed to walls and making good with cement mortar 1:3 or with PCC 1:2:4 complete all as specified and directed. 60 S&F 110mm bore PVC (SWR) Soil, waste and vent pipes single socketed in any length with rubber ring joints laid in trenches or in floors and making good with cement mortar 1:3 or with PCC 1:2:4 complete all as specified and directed. 61 S&F in repairs PVC 110mm bore Bendcomplete all as specified and directed. 62 S&F in repairs PVC (SWR) junction single, (Single T) equal or unequal with access door in110 mm bore complete all as specified and directed. 63 S&F in repairs PVC 75mm bore Bend complete all as specified anddirected. 64 S&F in repairs PVC 75mm bore Bend with access door complete all as specified and directed. 65 S&F in repairs PVC (SWR) junction single, (Single T) equal or unequal with access door in75mm bore complete all as specified and directed. 66 S&F in repairs PVC (SWR) vent cowl 110mm bore complete all as specified and directed. 67 S&F in repairs for PVC (SWR) floor/Nahani trap 75mm dia outlet, plain with grating including jointing with solvent cement to waste pipe, fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed. 68 Taking down chowkats or frames not exceeding 1.50Sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed. 69 Taking down chowkats or frames exceeding 1.50 sqm but not exceeding 4.00sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed. 70 S&F solid PVC door frame of size 50x47mm made of 5mm plain colour PVC sheet reinforced with MS square tube supply & fixing in opening as per specification and drawings complete all as specified and directed. 71 S&F Factory Made Solid PVC Moulded Door Shutter With Particle Board Core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face and 2mm plain colour PVC sheet on back face, supplying and fixing in frame at site as per specifications and drawing complete all as specified and directed. 72 S&F Box type steel window (Fatory made) outer frame made out ERW tube P section 65mm x 45mm x 25mm and shutter with glazed openable shutter of ERW tube P section 50 mm x 35mm x 20 mm openable (double) shutter with glazed openable shutter on (external side) and wire gauzed openable shutter on (Internal side) with steel pintal hinges, steel handle 100 mm long, mild steel tower bolt 02 nos on each shutter, stopper of Z section and its locking arrangement at mild steel hook and eye including 0.36mm dia nominal dia of stainless steel wire cloth avg width of aperture 1.40mm dia, 4 mm thick sheet glass window & 4mm figured glass for ventilators and guard bars (MS square bar 12mm dia), complete all as specified and directed.Note. The quoted rate against the above item shall also include(i)For provn of one shop coat of zinc chromate primer on all exposed steel surfacces and one coat of tar on the ends of steel frame in contact with bricks/concrete surface.(ii)04 Nos MS Steel Lugs of 20 x 5mm, MS flat 20 cm long over all welded to frames. (iii) PCC block for embedding lugs.(iv) 0.36 mm dia SS wire mesh.(v) 4mm thick sheet glass for window.(vi) Guard bars. 73 M&L Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed. 74 M&LPCC 1:3:6 type C-1(using 20mm graded crushed stone aggregate) for bed block for fixing hold fast, filling of pressed steel door framecomplete all as specified and directed. 75 M&Lproviding PCC 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregate) as in roof kerbs or mud stops rouded or chamfered on edgescomplete all as specifed and directed. 76 M&L Pressed steel frames (Factory made) made out of 1.25mm thick black MS sheet for doors, with one or more rebates including necessary s&f lugs, Butthinges, lock strike plate, etc complete, size of frame 125x60mm including bottom of each chowkat to be welded with 2 nos 25x25x3mm thick flat iron projecting 10 cm on either sidecomplete all as specified and directed. 77 M&L Pressed steel frames (Factory made) made out of 1.25mm thick black MS sheet for doors, with one or more rebates including necessary s&f lugs, Butthinges, lock strike plate, etc complete, size of frame 105 x 60mm including bottom of each chowkat to be welded with 2 nos 25x25x3mm thick flat iron projecting 10cm on either sidecomplete all as specified and directed. 78 S&F 35mm thick, factory made 2nd class hardwood glazed and skeleton shutters, open rebated and prepare to receive gauge etc (without sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitred beads for secruing glass/gauge etc size of member of shutter as specified in SSR Part-I Section 8 Clause 8.20(a), fitted to chowkats complete all as specified and directed. 79 S&F35mm thick flush shutters, solid core construction, with block board core and plywood face panesls, commercial type on bothe sides complete all as specified and directed. 80 S&F 18mm thick Plywood, grade BWR, type BB, fixed with screws to timber frame workincluding teak wood lipping on face complete all as specified anddirected 81 M&L0.9mm thick decorative laminate type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturers instructions complete all as specified and directed. 82 S&F Push to open Magnetic Catches for kitchen cabinet doors complete all as specified and directed. Make : Hettich, Hafale, Wurfel or equivalent as approved by GE 83 S&F Contnuous (piano) hinges, mild steel, bright finish or electrogalvanised width of flaps (when open) 30mm complete all as specified and directed. 84 S&F Stainless Steel Decorative Cabinet Handle 100 mmcomplete all as specified and directed. 85 S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed. 86 S&F Floor door stopper of aluminum alloy body and tongue anodized with hard drawn steel spring fixed in floor of length 150mm complete all as specified and directed. 87 S&F Stainless Steel butt hinges medium weight of size 100 mm fixed with stainless screws complete all as specified and directed. 88 S&F Extruded aluminium alloy handles 150 mm long fabricated type anodised complete all as specified and directed. 89 S&F 200mm size aluminium anodised, barrel tower bolt of extruded section complete all as specified and directed. 90 S&F 150mm long aluminium anodized barrel tower bolts of extruded section lcomplete complete all as specified and directed. 91 S&F 250mm long aluminium alloy anodised sliding door bolt with hasp and staple (bolt type) and fixingclips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed. 92 S&F Decorative Stainless steeltubular curtain rail of 25mm dia incl six nos curtain ring per running mtr and one number of brackets on each end and one no of globe on each end of the rod per opening of door / window complete all as specified and directed.(Make and material as approved by GE) 93 S&F 2nd class hardwood small fittings such as brackets of any type, latch and hinge blocks, shaped door and widnow stops and the like, including all necessary labour; articles not exceeding 200 cu. cm each complete all as specified and directed. 94 Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc) any thickness, including cover fillets but without frame work complete all as specified and directed. 95 S&F Powder coated galvanised iron frame work for seamless ceiling size 600mm x 600mm with main runner 38 x 24 x 0.90mm thick, cross tee 29 x 24 x 0.90mm thick and wall angle 24 x 24 x 0.90mm thick duly suspended with 6mm dia GI bar hangers 1200mm centre to centre both ways fixed with steel dash fasteners or from purlin from the roof with alignment clip complete all as specified and directed. 96 S&F 6mm thick Non Asbestos fibre cement building boards/Pre Laminated self embossed texture designer E-Board classic(Size 0.60M x 0.60M), HPSC (High pressure steam cured) to be fixed or laid/inserted to existing/new timber/GI/Aluminium/MS framework with screws as in ceiling complete all as specified and directed. 97 Dismantling of Plain or corrugated steel sheeting, any gauge, thickness complete all as specified and directed. 98 S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, height upto & inl triple sotrey bldg as specifiedare to be fixed using torque adjustable electronic gun screws drills of suitable capacity complete all as specified and directed. 99 Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick as in ridges, eves board of any colour having tensile strength of 550 Mpa as inroof covering/cladding to wall, fixed with self tapping screws in any heightcomplete all as specified and directed. 100 Dismantling boarding, any description, fixed in any position with nails complete all as specified and directed. 101 S&F rolled mild steel sections channel angle Tee section and in tubular sectionas in main and cross beams, hip and jack rafters; purlins,post where connected to common rafters and running rails fixed with angle cleat or other connecting plates conforming to Fe 410-W Gde-E-250, quality A complete all as specified and directed. 102 S&F framed work such as grills,gratings, etc with ends of bars shouldered and / or riveted or forged into spikes; framed guard ; barred iron doors; ladders ; framed balusters; walk ways; railing and simillar work Con-forming to Fe 290 Gde E-165, complete all as specified and directed. 103 Taking down cement plaster on brick or stone walls etc raking out joints hacking for key, scrabbing down water etc complete all as specified and directed. 104 M&L 15mm thick cement plaster in CM (1:4) on fair faces of brick or concrete surfaces using WPC where ever requiredas per manufacturerers instructions and finishing the surface even and smooth (without using extra cement) etc. incl finishing even and faircomplete all as specified and directed.Note: - WPC shall be measured and paid as supply only separetely. 105 M&L rendering 15mm thick on fair faces of brick work in CM 1:6 surface finished even and fair without using extra cement complete all as specified and directed. 106 M&Lrendering 10mm thick in CM (1:3) on fair facesor concrete ceiling surfaces finished even and fair without using extra cement complete all as specified and directed. 107 Supply only integral water proofing compound complete all as specified and directed. 108 M&Lapplying two coats of synthetic eneamel painting over a coat of pink primer on new wooden surfaces exceeding 10cm width or girth including preparation of surfaces complete all as specified and directed. 109 M&L applyingone coat of synthetic enamel paint to old decorated steel surfaces of girth exceeding 10cm including preparation of surfaces complete all as specified and directed. 110 M&L applyingtwo coats of synthetic enamel painting over a coat of red oxide zinc chrome primer on new steel surfaces over 10cm width or girth including preparation of surface complete all as specified and directed. 111 Preparing new plastered or unplastered surfaces of walls and applying two coats of distemper oil emulsion, white or tinted over & including a coat of primer complete all as specified and directed. 112 M&Lcomplete removal of existing surface and applying two coats of oil bound distemper over a coat of primer white or tinted on old decorated/undecorated surfaces of wall complete all as specified and directed. 113 M&L applying 2mm thick wallcare putty on walls complete all as specified and directed 114 M&L preparing new plastered or unplastered surfaces of Ceiling and applying two coats of distemper oil emulsion paint complete all as specified anddirected 115 M&Lcomplete removal of existing surface and applying two coats of Oil Bound Distemper over a coat of primer on old decorated/undecorated surfaces of Ceiling complete all as specified anddirected. 116 M&L applying2mm thick wallcare putty on ceiling complete all as specified anddirected. 117 M&Lpreparation of newly plastered surfaces of wall applying a layer of wall care putty 2mm thick (averaging) , Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed 118 M&Lcomplete removal of existing treatmentby srapping down of old surface of wall applying a layer of wall care putty 2mm thick (averaging) , Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed. 119 M&L 75mm thick PCC 1:3:6 type C2 (using 40mm graded crushed stone aggregate) as in plinth protection laid in bays including finishing even and smooth w/o using extra cement and joint filling using sealing compound grade A complete all as specified and directed. 120 M&Lcement concrete 1:2:4 type B-1 (using 20mm graded crushed stone aggregates) as in surface channels and drains complete alll as specified and directed. 121 M&Lextra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc complete all as specified and directed. 122 Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. complete all as specified and directed. 123 Taking down unserviceable any type of Main Switch, DBs including MCBs incl wooden/GI/MS sheet board etc and removing from site and making good the disturbed surface of wall etc complete all as specified anddirected. 124 Taking down unserviceable any type of copper/aluminium sub main wiring of any size/core/type complete including conduits/casing caping etc, removing the materials/debris and making good the disturbed surfaces of walls, floors and ceilings etc to match with the original existing finish complete all as specified and directed. 125 M&Lconcealed point wiring with FRLS-H, PVC insulated, unsheathed multistranded copper conductor cables 1100 Volts grade of 1.5 sqmm size (Phase and Neutral) alongwith one earth continuity conductor with FRLSH PVC insulated unsheathed multistranded copper conductor cable 1100 Volts grade of 1.5 sqmm size through and including 20 mm dia (medium grade) rigid non metallic PVC concealed conduit terminated and suitable for modular metal flush box as per site requirement for fixing of switches, sockets, fan regulators etc including testing on completion complete including cutting chases for concealed conduit piping in making good to facing and pointing in using cement mortar 1:3 and making good to disturbed surface for the following. Note: (a) Rate of modular cover plates are paid seperately in respected items. (b) Rate for any type of way connector to fix fittings are deemed to be included in the item cost. 126 Desciption all as per item No 125 here in above for one 3 pin socket outlet, 5 Amp on same modular board with other switches, with cable 1.5 Sq mm size complete all as specified and directed. 127 Description all as per item No 125 here in above for one 3 pin socket outlet 5 amps on the Indepdent modular board with other switches, with cable 1.5 Sq mm size complete all as specified and directed. 128 Supply and fixing of Socket,6A - 3 pin combined 2 module,universal socket with child safety shutter, Shrouded terminals compatible with all standard mobile chargers, ISI marked for the same board complete all as specified and directed. 129 Supply and fixing of Modular switch socketCombination outlet multipurpose 3/5 pin 5 amp flush type, ISI marked complete all as specified and directed. 130 M&Lone point wiring with PVC insulated un-sheathed cable with stranded copper conductor FR-LSH conforming to IS : 694 of size 2.5 Sq mm single core, including one No. 2.5 Sq mm single core PVC insulated un-sheathed copper cable FR-LS as continuous earth wiredrawn in and including PVC conduit with all accessories of same grade,concealed on wall/ceiling including terminatedin to Modular switch board / Cast iron/pressed steel terminal box 60mm deep of required sizemade out of 2mm thick MS sheet duly painted both sides with 3 mm thick plasticlaminated sheet top cover fixed with brass screw & cup washers for mounting switch socket combination 2 in 1, 3 pin, 5 and 15 Amp flush type / modular type on the independent board complete all as specified and directed. 131 Supply and fixing of Switch and Socket outlet 16A - 5 pin combined 3 module,(Fabio classic white) shuttered socket (heavy duty) 3 pinunversal socket with child safety shutter, Shrouded terminals compatible 2 ton AC and 3.5KW geyser, ISI marked for the same board complete all as specified and directed. 132 All as per item No.125 but one light point controlled by two 2 - way switches, with cables 1.5 sq. mm size complete all as specified and directed. 133 Supply and fixing modular switch 2 way 6A,1 module complete all as specified and directed. 134 Supply and fixingCeiling rose, 3 phase/PVC/polycarbonate, isolated body type complete all as specified and directed. 135 S&F in repairs of tube light fitting, with LED batten with polycarbonate housing and integrated electronic drive 1x 22 watts 4 feet twin light mode rechargeble fitting with white acrylic cover along with LED lamp white colour complete including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed. 136 S&F Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fitting of LED lamp 9 watt complete all as specified and directed. 137 S&F LED lamp 9 watt complete all as specified and directed . 138 Hanging only ceiling fan and connecting up including provision of cable from ceiling rose to fan complete all as specified and directed. 139 Fixing only exhaust fan and connecting up including provision of cable from ceiling rose/connector to fan complete all as specified and directed. 140 Supply and fixing modular fan regulator, 120W- 2 module regulator electronic step type 230 Volts single phase complete all as specified and directed. 141 Supply and fixing of Modular switch 1 way 6A, 1 module modular Switch fabio classic white series/Switch fabio classic white with indicator, ISI marked switch complete all as specified and directed. 142 Disconnecting electric supply from electric meter and dismantling MS electric meter box of any size including electric meters, switch gear, MCCB/MCBs etc complete and supply fabricate testing and commissioning of MS sheet electric meter box 2 mm thick double door with locking arrangement of size/dimension not less than 130x75x30 cm with suitable thickness of ylem sheet for fixing existing electric meter -06 Nos including provision of new MCCB 160 A -01 No,MCB SPN 63 A-06 Nos with suitable size of aluminium bus bar for phase 7 neutral and see through glass -08, connecting internally prewired copper conductor with electric meter connecting of required size applied with power coated synthetic enameled paint and making good to the disturbed wall surface complete all as specified directed. 143 Fixing only Electric Water Heater and connecting up including provision of cable from Geyser Point complete all as specified and directed. 144 S&F DB with sheet metal enclosure 240 volts, 8 way with 200 Amp rated bus bar single pole and neutral double door type for MCBs including mounting work as required in positioncomplete all as specified and directed 145 Supply and fixing of amp rating 240V, 10KA curve miniature circuit breaker (MCB) SPN and current carrying capacity 40 Amps in the MCB DB complete with connection testing and commissioning complete all as specified and directed. 146 Supply and fixing of amp rating 240V, 10KAcurve miniature circuit breaker (MCB) SP and current carrying capacity 5-32 Amps in the MCB DB complete with connection testing and commissioning complete all as specified and directed. 147 M&LSub Main wiring using FRLS Insulated unsheathed, multistrand copper conductor FRLS PVC cable 2 runs of size 4 sqmm for phase and neutral and 4 Sq mm for earthing. drawn through rigid PVC conduitof suitable sizefixed on wall/ground/Ceiling etc., and complete all as specified and directed. Note: Phase should be Red / Yellow / Blue, neutral should be black and earthing wire should be green in colour. Two runs of cable for phase / neutral and one run of cable for earth incl conduit will be measured and paid as one unit length. 148 M&LSub Main wiring using FRLSH Insulated unsheathed, multistrand copper conductor FRLS PVC cable 2 runs of size 6 sqmm for phase and neutral and 6 Sq mm for earthing. drawn through rigid PVC conduitof suitable sizefixed on wall/ground/Ceiling etc., complete all as specified and directed.Note: Phase should be Red / Yellow / Blue, neutral should be black and earthing wire should be green in colour. Two runs of cable for phase / neutral and one run of cable for earth incl conduit will be measured and paid as one unit length 149 Supply and fixing in repairs LED Bldgs Security light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete. including connections with 2 run of 2.5 Sq mm copperunsheathed wire multistranded from Distribution box to the connector of fitting, complete all as specified and directed. 150 S&F street light bracket made out of GI tubing 32 / 40 mm dia, light grade of approx length 1.2 mtr long bend to shape suitable for security light fittings with necessary MS clamps - 02 Nos with one coat of anti corrosive primer and two coats of aluminium paint including nut, bolt, washers etc complete all as specified and directed. 151 M&L Earthing complete with galvanised steel earth plate, electrode, 600x600x6.0 mm thick burried directly in ground (earth pit not less than 2.25m deep below normal ground level) connected to galvanised earth lead wire 4.0 mm dia by mens of nuts, bolts and washers of GI as shown in electrical plate No. 5 of SSR Part-I Connected to earthing ten point all as specified and including necessary earth pit PCC 1:3:6 chanber be 50mm thick PCC 1:2:4 chamber cover with 6mm dia mild steel reinforcement of 10 cm c/c spacing both ways in lieu of CI cover , watering arrangement shall be made with GI pipe medium grade of 20mm dia including funnel and protection to earth lead shall be provided with GI pipe light grade 15mm dia upto 7.5 from the earth plate electrode and refilling of soil etc including necessary excavation and earth work in any strata and PCC chamber complete all as specified and directed including demolition of existing earth pit including taking out old materials. 152 S&F modular white cover plate with frame 3 module complete all as specified and directed. 153 S&F modular white cover plate with frame 6 module complete all as specified and directed. 154 S&F modular white cover plate with frame 8 module complete all as specified and directed. 155 Excavation in trenches in any type of soil not exceeding 1.5m wide and not exceeding 1.5m in depth and getting out for taking out/laying of GI pipe of any size complete all as specified and directed. 156 Returning, filling icluding spreading, leveling, watering and well ramming in layers not exceeding 25cm complete all as specified and directed. 157 Removing excavated materia;s to distance not exceeding 50m and deposting where directed as level not exceeding 1.5m above the starting point complete all as specified and directed. 158 Taking out/taking down old unserviceable damaged GI/PPR pipe of following sizes from excavated trenches including removing of fittings all as directed for necessary replacement /relaying serviceable GI pipe size of 50mm dia complete all as specified and directed. 159 Description all item No 158 but 32/40 mm dia complete all as specified and directed. 160 Description all item No 158 but 25 mm dia complete all as specified and directed. 161 Supply and Laying of PPR pipes 3- layer SDR 7.4 of outer diameter of pipes as following UV stabilized and antimicrobial fusion welded having thermal stability for hot and cold water supply all PPR plainand brass threaded polypropylene random fittings laid in trenches including fittings and testing Size of 25 mm dia complete all as specified and directed. 162 Description all item No 161 but 32 mm dia complete all as specified and directed. 163 Description all item No 161 but 50 mm dia complete all as specified and directed. 164 M&L construction of Brick Masonry valve chamber of size 600x600x600mm (Internal dimensions) with PCC 1:4:8 foundation 150mm thick, brick work built in CM 1:6, PCC 1:3:6 coping 50mm thick, plastering 15mm thick in CM 1:6 to all internal and exposed surfaces including excavation earthwork in hard/dense soil, MS sheet cover 4mm thick and MS equal angle iron 50mmx50mmx6mm frame as per existing sizewith locking arrangement embedded in PCC suitable for 25/40/50mm gate valve and painting to MS cover with two coats of synthetic enamel paint over one coat of red oxide primer etc complete including dismantling old/damaged valve pits complete all as specified and directed. 165 Making connection of PPR distribution branch with PPR main ofsizes 50mm to 75mm by providing and fixing tee including cutting and making fusion joint etc complete all as specified and directed. 166 Taking out unserviceable Gate valves from water pipe line for necessary replacement all as directed for valve size 15mm to 32mm complete all as specified and directed. 167 Taking out unserviceable Gate valves from water pipe line for necessary replacement all as directed for valve size 40mm to 80mm. 168 Supply and fixing PPR gate valve (brass insert) of size 25mm dia including connection and testing complete all as specified and directed. 169 Supply and fixing PPR gate valve (brass insert) of size 50mm dia including connection and testing complete all as specified and directed. 170 S&F GI Flat strip clamps of size 25mm x 3mm duly bended as per the size of GI tubing and site condition,drilled complete all as specified and directed. 171 Supply and fixing of heavy rust proof passivated bolts made of steel of size 8mm dia 75mm long including necessary drilling on wall for fixing of steel frame complete all as specified and directed. 172 M&L Lagging on pipes of internal dia 15mm, used in external water supply or plumbing all round with, 40mm thick bonded mineral wool preformed ‘SNAP ON’ pipe sections of density 144 Kg/cum conforming to IS 9842, provided with chicken mesh wire netting 25 gauze 20mm mesh and finally covering with plaster of pairs including taking down old, complete all as specified and directed for the size of 25 mm bore tubing. 173 All as per item No. 172 above but 32 mm bore tubing complete all as specified and directed. 174 All as per item No. 172 above but 50 mm bore tubing complete all as specified and directed. 175 Supply and laying in repairof XLPE insulated,sheathed,armoured,heavy duty LT 1100 volts grade cable 25 Sqmm3.5 core with aluminium conductor laid in trenches/pipes, fixed topoles/walls with suitable saddle complete all as specified and directed. 176 Supply and laying dry river sand laid in trenches as cable cushioning and covering complete all as secified and directed. Note : Punned thickness only shall measured and paid. 177 M&Lbrick well brunt locally available sub classB laid over sand cushioning to cable in trenches keping width of brick parallel to the length of cable complete all as specified and directed. 178 Notes :-An amount of Rs. 90762.00 on account of Credit Schedule for Schedule A Part-II shall be deducted from total quoted amount of BOQ to arrive at the contract sum.
