Tender For Special Repair To Building No P-531/01 To 04 (Or Md Accommodation) Of Jat And Other Misc Sanctioned Works At Itarana Mil Stn, Alwar; 1 Taking down cement or cement lime plaster, any description on brick or stone walls,etc including racking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed by Engr-in-Charge. 2 Demolition cement concrete (unreinforcement) in ground floor and paving n exc 15 cm thickness (below or above ground level) & removal complete all rubbish materials complete all as specified and directed. 3 Demolition of cement concrete (reinforced) in landing slab, chullah hoods, manhole covers , Roofs, Floors, beams, stair case, landing, chajja and similar suspended work complete all as specified and directed. 4 Dismantling floor hearth wall tiling (but not backing) removing servicable tiles to store rubbish off the premisses complete all as specifiedand directed. 5 Demolition of brick work or stone/boulder masonry built in cement mortar incl all quoins, arches, pillars& precast concrete masonry etc complete all as specified & directed. 6 Demolition of existing lime concrete/PCC padding, Roof treatment of any thickness laid over RCC roof/Chajjas etc removing complete layer of bitumen under concrete/PCC Padding, cleaning and washing of roof with water to remove dust etc as prepareation to receive treatment complete all as specified and directed. 7 Taking down chowkats or frames with shutters (without taking off shutters from the frames) n exc 1.5 but each complete all as specified & directed. 8 Taking down chowkats or frames with shutters (without taking off shutters from the frames) exc 1.5 but n exc 4 sqm each complete all as specified & directed. 9 Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc,laid , bedded and pointed in any mortar all as specified & directed. 10 Cutting holes into stone wall built in cement mortar or cement lime mortar for inserting hold fast and making good dismental portion in CM (1:3) or cement concrete (1:2:4) type B-1 exc one brick but n exc two brick as required complete all as specified and directed. 11 M & L for 25mm thick PCC 1:2:4 type B-1 (using 12.5mm graded aggregate) as in leveling coarse of floors and roof complete all as specified and directed. 12 M & L for 75mm thick PCC 1:4:8 type D-2 (using 40mm graded aggregate) as in sub base of roof/floor/ pavings/path etc complete all as specified and directed. 13 M & L for providing cement concrete 1:2:4 type B-0 (Using 12.5mm graded stone agggregate) as in padding and levelling course on roof and floor complete all as specified & directed. 14 M & L Cement concrete type C-1 1:3:6 (using 20mm graged stone aggregates) as in plinth protection 75mm thick and surface to be finished even and smooth without using extra cement. Plinth protection shall be laid in pannels x.exc 1.5 mtr 6mm wide and 10mm deep joints shall be made between wall & plinth protection and between panel. Joint shall be filled with bitumen mastic and sand in proporation 1:3 (one part of bitumen and three part of sand) complete all as specified and directed 15 M&L for PCC 1:2:4 type B-1 using 20mm graded aggregate as in cills, coping steps, tank staging, sesmic and other similar courses, lacing courses parapet and railing upto 60cm ht kneeler kerb and alike including weathering, slightly rounded or chemfered angle and throating complete all as specified and directed. 16 M&L for PCC (1:4:8) type D-2 (Using 40mm stone aggregate) as in foundation concrete complete all as specified and directed. 17 M&L PCC 1:5:10 type E2 for sunken filling, foundation, filling and mass concrete complete all as specified and directed 18 Providing precast cement concrete 1:2:4 type B-1 as in landing, cover slabs (for manholes etc) Chajjas, water troughs, managers, shelves and SImilar article with plain faces complete all as specified and directed. 19 M&L plain cement concrete 1:2:4 type B0 in roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and directed. 20 M&L rendering 15mm thick in cement mortar 1:4 including WPC @ 3% by weight of cement on stone/brick masonry finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.Note : quoted rate is deemed to be inclusive for work at any height and location including cost of scaffolding and all other equipments reqd to execute the work complete all as specified and directed. 21 Supply only liquidwater profing compound as per IS-2645 complete all as specified and directed. 22 Taking down carefully existing bitumen tarfelt including plaster of any description over the surfaces of roof, terraces including flashing and junction of parapets/curve walls etc and removing of the rubbish and deposting where directed complete all as specified and directed. 23 M&L for 15mm thick cement plaster in CM 1:6 on other than fair faces of brick work or concrete surface finished even and smooth without using extra cement complete all as specified and directed. 24 M&L for Rough cast plaster on exterior wallsapplying the under coat of cement and sand mortar 1:3 not less than 10mm thick and while it is still in plastic state the roughcast mixture consisting of crushed stone or fine gravel aggregate (size between 6 to 12mm) mixed with coarse sand and cement in the ratio of 1:1:1 shall be applied and finished even as per manufacturer instructions complete all as specified and directed. 25 M & L for 15mm thick screed bed on fair faces of concrete/brick surfaces in CM 1:4 with water proofing compound @ 3% of wt of cement finished even and smooth in order to maintain proper slope over exsting roof surfaces for laying APP based polymeric membrane finished complete all as specified (Polymeric membrane and WPC shall be measured and paid seperately here in after) complete all as specified and directed. 26 M & L for rendering 5 mm thick cement plaster in CM 1:3 as in ceiling and finish the surface even and smooth without using extra cement complete all as specified and directed. 27 M&L water proofing treatement to RCC roof slab including parapet comprising of following course of treatement/specified from bottom to top (a) Applying Bituminous primer@ 0.40 Ltr per sqm over plastered surfaces of roof including parapet surfaces. (b)Over the priming coat laying one layer APP based polymeric membrane of approved manufacturer, 3 mm thick weight not less 3.6 Kgs/Sqm and upper side of membrane thermally insulated with white mineral gravel finish , unifirmly embeded during manufacturing process shall only be used, it shall be laid by torch application side overlap should be 75mm and end shall be 100mm.For parapets, membrane shall be taken to a height of minimum 60cm and then inserted inside parapet in groove.The same shall be finished by a membrane flashing complete all as specified and directed. 28 M&L for Glazed coloured ceramic tiles in vertical surface 300x450x7 / 300x600x7 mm thicklaid over and including 10 mm rendering in CM 1:4 set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile Complete all as specified and directed. 29 M&L for non skid ceramic tiles (coloured) 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. laid over and including 10 mm rendering or bedding layerin CM 1:4set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile Complete all as specified and directed. 30 M&L non skid ceramic8-10mm thick (square/rectangular), polished, coloured (light shade as approved), area of each tile not exceeding 0.36 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and directed. 31 M & L non skid ceramic 8-10mm thick (square/rectangular), polished, coloured (light shade as approved), area of each tile not exceeding 0.36 sqm on vertical surfaces such as dado, skirting etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over & including 10mm thick rendering in cement & sand mortar 1:4 complete all as specified and as directed. 32 M&L for machine cut Green Marble flooring 18-20 mm thick as in floor, cooking platform, treads etc laid over 20mm thick screed bed or bedding layer in CM 1:3 set and jointed in neat cement slurry and jointed with grey cement slurry mixed with pigment to match the shade of the slab inclding rubbing jand pokshing by machine and including frinding complete all as specified and directed. 33 M&L for machine cut Green Marble18-20 mm thick as in riser of steps, skirting, dado and pillar set over 10 mm rendering in CM 1:3 and jointed with grey cement slurry mixed with pigments to match the shade including rubbing and polishing complete all as specified and directed. 34 M&L for 18-20 mm thick Granite(of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills,cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match withshade of granite laid over 15 mm screed bed or bedding layerin CM 1:3, including grinding of edges to curved surface finish complete all as specified and directed. 35 M&L for machine cut 25 to 30 mm thick kota stone in single piece as in shelves and similar works laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing including ball nosing of exposed edges and including dismantling old stone slabs complete all as specified and directed. 36 Providing and fixing facory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonete and natural fibers (wood powder / rice husk / wheat husk) and non toxic additives (maximum toxicity index of 12 for 100gms) having minimum density of 650 kg/cum and screw withrawal strength of 1800N (pace) & 900 N (Edge) minimum compressive strength 50n/mm2, modulus of elasticity 850N/mm2 and resistance to spread of flame of class A category with property of being termite/borer proof, ater/moistur proof and fire retardant, WPC to be laminated with PVC foil of minimummicrons thick of approved design psted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS screws, complete all as specified and directed. (Note : stainless steel butt hinges shall be paid separately) 37 S & F Gauzed shutter made of mild steel framed work as in door frames mad of hollow / square/rectangular /curcular section and other covering door to be prepared for handing or sliding with including eikther hooks, fittings, mortac lock and hanging also fasterning and fixing, necessary arrangements for fixing or wiremess necessary bolting incl weldin complete, wire gauge will be measured and paid separately complete all as specified and directed. 38 Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardanand fixed in position with MS hold fast/ugs/SS dash fasteners of required diaincluding necessary hold fast/lugs or SS dash fastner complete all as specified and directed. 39 S&F Aluminium windowsmade of 1.59 thick powder coated (thickness of powder coating not less than 50 micron) as per aluminium section of size given below .Aluminium window will be of double shutter ofglass/ wire gauge shuttersincluding allnecessary accessoriesjointing cleats , glazing clips, rubber neoprene packing, for fixing glass/ wire gauge,aluminium handles and tower bolt 2 Nos 100 mm ‘D’ Type in each door, 2 Nos 100 mm aluminium hinges including necessary steel screws complete all as specified and directed.The size of different aluminium section to be used is as under (a) Outer Frame 125X45X2.00 mm thick (b) shutter frame section size 44X44X1.59mm thick for glass and 44x25x1.59mm for wire gaugeNote: Rates quoted are inclusive all fittings and fixtures. Glass and wire gauge& MS grill will be paid separately in respective items. 40 S&F galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks, or galvanised wire staples to wooden/steel frames with beading complete all as specified & directed. 41 S&F Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks, or galvanised wire staples to wooden/steel frames with beading complete all as specified & directed. 42 S&F sheet glass, ordinary quality 4.80 mm thick fixed with rubber beading and clips size of glass n.exc 2 sqm in each pane complete all as spd & directed. 43 S&F in repair vitreous china squatting pan of Orrisa pattern size 580mmx440mm white with integral foot rest (excluding flushing cistern and flush pipe) complete incluidng provision of lime concrete bedding complete all as specified and directed. 44 Supplyand fixing in repair PVC flushing cistern low level 10 ltr cap with inlet ball valve float and handle syphonic action type incl brackets and flush pipe of polythene of low or high density ISI marked complete all as specified and directed. Make : Cera / Jaquar / Hindware 45 S&F in repair 15mm dia bib tap cast coper alloy chromium plated fancy type crutch or butter fly handle screwed down screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed. Make Jaquar cat Part No CON-047KN or equivalent of Cera / Hindware 46 S&F in repair 15mm dia stop valve/angle valve of copper alloy fancy type chromium platedscrewed down high pressure with crutch or butter fly handle screwed on both ends for iron pipe or for union complete all as specified and directed. Make : Jaquar cat part No CON-053KN or equivalent of CERA/Hindware 47 S&F in repair swivel shower rose(fancy type) chromium plated shower rose 125mm size with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and directed. Make: Jaquar cat part No OHS-1989 or equivalent of Cera / Hindware 48 S&F in repair 600mmx450mx5mm thick looking mirror of selected quality glass mounted on 6mm thick AC building board or commercial plywood incl framing and fixed to wooden plugs with chromium plated screws & cup washers & fixed in repair i/c taking out old mirror complete all as specified and directed. 49 S&Fin repair Vitreous china conrner wash hand basin of soze 550mm x 435mm / 400mm x 450mm excluding taps waste chain plug stopper but including brackets waste pepe cutting pinning in ends of brackets complete all as specified and directed. Make : CERA /JAQUAR/HINDWARE. 50 S&F in repair 32 mm dia PVC flexible waste pipe for WHB/Sink 600 mm long with PVC coupling all as directed fixed in repair complete all as specified and directed. 51 Taking up or down steel tubing and connections including cleaning for refixing or removal to store 20mm bore pipe complete all as specified and directed. 52 Refixing old steel tubing and connection in new or old poSItion (walls,ceiling,floor etc) bore of pipe in 20mm dia. 53 S&F tubes medium grade galvanised with and including all fitting and fixed bore of 20 mm dia complete to walls and ceiling or laid in floors of 20 mm bore complete all as specified and directed. 54 Taking up or down steel tubing and connections including cleaning for refixing or removal to store 15mm bore pipe complete all as specified and directed. 55 Refixing old steel tubing and connection in new or old position (walls,ceiling,floor etc) bore of pipe in 15mm dia complete all as specified and directed. 56 S&F tubes medium grade galvanised with and including all fitting and fixed bore of 15mm dia complete to walls and ceiling or laid in floors of 15mm bore complete all as specified and directed. 57 S&F in repairs sink with drainage board made of stainless steel 1mm thick for kitchen with plugs, washers and wastes, including fixing with cast iron cantilever brackets, bedding in cement mortar on to dwarf wall, connecting union to pipe, overall minimum size 915mm x 460 mm with bowl size 410mm x 330mm x160 mm including 32mm dia waste pipe of polythelene of low or high density, 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, making holes in walls for brackets and fixed in CM 1:3 or PCC 1:2:4 type B0, complete, including taking down old unserviceable sink complete all as specified and directed. 58 S & F in repair stop valves 20mm bore, cast copper alloy screwed down high presure, with crutch of butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed. 59 Dismantling of water tanks of capacity exc 250 but n exc 500 ltrs & removing to stores complete all as specified & directed. 60 S&F 500 ltrs capacity rotational moulded polyethylene water storage tanks (cylinderical vertical with closed top)vhoilsted and fixed in position all as specified in SSR Part-I complete all as specified & directed. 61 S& Fixing in repair ball valve brass high pressure with polythene floatand fly nut screwed on iron pipe ad fixed 20 mm bore of pipe complete all as specified and directed. 62 S&F in repair PVC connection 15mm size with PTMT nuts of length 600mm complete all as specified and directed. 63 S&F in repair Brass chromium plated Tubular towel rail 20mm dia, D type, 60cm long between flanges complete all as specified and directed. 64 S&F in repair Floor Drainer with Collar and Cockroach Trap/Jali with or without waste hole complete all as specified and directed. 65 S&F in repair brass chromium plated soap dish, complete all as specified and directed. 66 S&F in repair brass chromium plated towel ring incl a pair of CP brass bracket complete all as specified and directed by Engr-in-Charge. 67 S&F in repairs 15 mm bore fancy type long body bib tap, half turn, with wall flange, cast copper alloy with capstan heads, chromium plated, screwed for iron pipe or for brass ferrule, complete all as specified & as directed. Make JAQUAR Cat Part No CON-107KN or equivalent of CERA / HINDWARE 68 S&F in repair15mm dia bore cast copper alloy chromium plated fancy typepillar tap with outcold & hot water complete all specified and as directed . Make : JAQUAR Cat part No CON-021KN or equivalent 69 S&F in repair CP brass mixer for Wallmixer hot & cold water for screwed down for iron pipe and fixed bore of pipe in 15 mm complete all as specified and directed. Make :JAQUAR cat part No CON-219KN or equivalent 70 S&F in repair PVC (SWR) pipes of 75 mm nominal outside diameter (Type B with wall thickness 3.20 to 3.8 mm) single socketed in any length with rubber ring joints laid in trenches or in floors of 75mm pipe i/c taking out old u/s PVC/CI pipe with fittings complete all as specified and directed. 71 S&F in repair PVC (SWR) pipes of 110 mm nominal outside diameter (Type B with wall thickness 3.20 to 3.8 mm) single socketed in any length with rubber ring joints laid in trenches or in floors of 75mm pipe i/c taking out old u/s PVC/CI pipe with fittings complete all as specified and directed. 72 S&F in repair PVC (SWR) pipes of 75 mm bore single socketed in any length fixed to wall i/c taking out old u/s PVC/CI pipe with fittings complete all as specified and directed. 73 S&F in repair PVC (SWR) pipes of 110 mm bore single socketed in any length fixed to wall i/c taking out old u/s PVC/CI pipe with fittings complete all as specified and directed. 74 S&F in repair PVC (SWR) floor trap, plain with grating including joining with solvent cement 75 mm dia complete all as specified and directed. 75 S&F in repair PVC (SWR) bend 75mm bore of any radius complete all as specified and directed. 76 S&F in repair PVC (SWR) bend 75mm bore of any radius with access door complete all as specified and directed. 77 S&F in repair PVC (SWR) bend 110 mm bore of any radius complete all as specified and directed. 78 S&F in repair PVC (SWR) bend 110 mm bore of any radius with access door complete all as specified and directed. 79 S&F in repair PVC(SWR) branch piece single PVC (SWR) (Single T) equal or unequal of 110 mm bore with access door complete all as specified and directed. 80 S&F in repair PVC(SWR) branch piece single PVC (SWR) (Double T) equal or unequal of 110 mm bore with access door complete all as specified and directed. 81 S&F in repair PVC(SWR) branch piece single PVC (SWR) (Single T) equal or unequal of 75 mm bore with access door complete all as specified and directed. 82 S&F in repair PVC (SWR) vent cowl 110 mm complete all as specified and directed. 83 Demolition and breaking up drain pipes (Salt glazed stone ware,AC, or Reinforced concrete) or 100mm dia set in cement mortar including PCC bed to drain pipe, packing under & haunching against the sides of drain pipes all as specified & directed by Engineer-in-charge. 84 S&F for 75mm thick steel fibre reinforced (SFRC) man hole cover with iron frames (medium) complying to the standard specifications as mentioned in the IS 12592 BIS Standard, minimum load bearing capacity 5 ton/sqm, in square, rectangular or circular shape complete all as specified & as directed. 85 M&L 150mm bore reinforced concrete pipe, class NP2, laid and jointed (in CM 1:1) complete with collars including demolition and breaking up old existing pipe complete all as specified and directed. 86 M&L for cement concrete (1:4:8) type D-2 (using 40mm graded stone agg) as bed to drain pipe including in packing under and haunching against sides of pipes after they are laid and tested in complete all as specified for 150mm dia pipes. 87 M&L for cutting into existing manholes / Septic tank for connecting new drains making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B1 smooth finished and reforming benching as required for 100mm bore pipe complete all as specified and directed. 88 S&F mild steel butt hinges medium weight colod rolled of size 100mm, ISI marked complete all as specified and directed. 89 S&F Stainless Steel hing pin butt hinges 100mm long complete all as specified and directed. 90 S&F in repair stainless steel,sliding door bolt with hasp,staple (bolt type) 300mm longnot less than 12mm dia with and incl minimum of 06 bolts and nuts, 4 on plate and 2 on staple and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, plate and fixed complete all as specified and directed. 91 S&F stainless stee, barrel tower bolts of extruded section and fixed 150 mm long complete all as specified and directed. 92 S&F stainless stee alloy handles 125mm size fabricated type anodized ISI marked complete all as specified and directed. 93 S&F stainless stee barel tower bolt 200mm long stove enamelled black with bright bolt & fixed complete all as specified and directed. 94 S&F stainless stee bow handle of 150mm size oval type stove enamelled blackcomplete all as specified and directed. 95 S&F in MS Retractable Hinge fixed to wooden or steel frames with Screws/welding as required at site complete all as specified and directed. 96 S&F 140 mm long Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring,with vulcanised rubber piece.fixed in floor complete all as specified and directed. 97 S& F in repair stainless steel plate rack out of 1.00 mm thick sheet of size 900 x 750 mm and depth of shelves 230 mm with partition for small /large plates made out of stainless steel 24 gauge all as per sampleto be hanged on wall by the help of steel screws grouted in walls with rawl plug design as approved by GE/Kept in GE Office 98 M&L for pressed steel shutter 1mm thick including pressed steel frame of 1.25 mm thick sheet,12mmdia M S rod for locking , two nos chromium plated handle and one mortise pattern lock inclu two coats of spary painting over a coat of shop primer complete all as shown on drg no TD/2004/29 sheet no 1/3 to 3/3 99 S&F(in repair) curtain rod with fixing bracket, stops, rollers etc complete all as specified and directed. 100 S&F in repairs Stainless Steel drapery rod of 25 mm inner dia (in length as directed ) of approved colour with & including matching finials at both ends and pair of SS brackets fixed at both ends with PVC rawl plug & steel screws on walls/beams including PVC curtain rings of matching colour @10 cm c/c all as specified and directed 101 M&L for 50mm thick sand stone slab in sunshades, chajjas,shelves, cills, landings, cover stones, templates etc not exc 2m in length, punched dressed on face and along exposed edges, self faced on the other SIde and set and pointed in cement mortar 1:4 complete all as specified and directed. 102 M&L for TMT bars 10mm dia and over cut to length to shape required including cranking, bending spirally or hooping for columns, hooking ends & binding with & including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed. 103 All as per srl itemNo 102.00 but for 6mm to 8mm dia TMT bars complete all as specified and directed. 104 Excavating in trenches n exc 1.50m in width and n exc 1.50m in depth for foundation, manholes etc as well as n exc 10 sqmm on plan area and getting out in soft/loose soil all as specified and directed. 105 All as per srl item No 104.00 but depth exc 1.5 m but n exc 3.0m. 106 All as per srl item No 104.00 but depth exc 3 m but n exc 4.5m. 107 Returning, filling in, including spreading, levelling, watering and well ramming in layers n exc 25 cm thick in soft/loose soil. 108 Removing excavated soil to a distance exc 50m and depositing where directed at a level n exc 1.5m above the starting point. 109 M&L for brick work with sub class B bricks, straight or curved on plan to any radius, built in 1:4 as in half brick thick wall complete all as specified and directed. 110 M&L for brick work with sub class B bricks, straight or curved on plan exceeding 6 mean radius, built in CM 1:6. 111 S&F frame work such as grills,gratring etc,with ends of bars shouldered &/or riveted or forged into spikes,framed guard bars, barred iron door ladder,frame balusters,walk ways, railing,frame work or water tanks & SImilar work conforming to Fe-290 Gde E-165. 112 M & L flat iron as in hold fast welded to angel iron door/window frames complete all as specified and directed. 113 S & Ffor framed work as in doors or gates or tank cage, angle or other covering door ect to be prepared for handing or sliding with including either hooks and hinges or steel hanging door fittings and inluding all necessary nuts and bolts and welding reqd and hanging also fasterning and fixing complete conforming to FE-290 GdeE-165 complete all as specified and directed. 114 M & L for welded mild steel wire mesh of mesh size 30mm x 30mm and wire size 1.4mm incll all necessary nuts and bolts / welding clamps reqd for fixing into angle iron frame complete all as specified and directed. 115 M&L for Vibrator moulded (Coloured) precast concrete interlockingpaver block with grey cement and pigment any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 grade laid over 25mm thick sand cushionand filled the joints with dry sand after laying the paver block complete all as specified and directed. 116 Treatment of sunken portion is as follows :-M & L for water proofing treatment in sunken floors as described hereunder:-(i) Sunken floor and sides upto finished floor level shall be plastered with 15mm thick cement plaster in mortar 1:4 mixed with water proofing compound @ 3% by weight of cement.(ii) Preaparing plastered surfaces and providing APP polymeric water proofing membrane, minimum 3mm thick and weighing not less than 3.0 Kg/Sqm of make super thermolay manufactured by STP Ltd or ‘Hyper Plas’ (Polyster) manufacturedby M/S IWL Ltd or ‘Shaliplas’ (polyester) manufactured by M/S Capital Steels and chemicals Pvt Ltd as approved by GE, black finish reinforced with non-woven polyester matt, with a thermo fusable finish laid over compatible bitumen primer (Bitumen primer shall be TANK MASTIC of M/S STP Ltd or ‘EMW FLATE’ of M/S Texas India Ltd}at the rate of 0.40 Ltr/Sqm torching overlaps with a propane or a butane gas torch, with a overlap of 75mm at the sides and 100mm at the ends and sealing including applying a coat of cold emulsion bituminous primer all as per manufacturer’s instructions, complete all as specified and as directed.Note:(i) Polymeric membrane shall be laid in sunken floor and on sides upto finished floor level (ii)The waterproofing treatment shall be got carried out by the manufacturer or their authorized applicators.(iii) Above aspects are deemed to be included in quoted rate. (iv) Horizontal floor area shall be measured for payment purpose. 117 S&F for preparation of new steel surface/old untreated of any description over 10cm width or girth & applying two coats of synthetic enamel paint over a coat of primer complete all as specified and directed. 118 M&L for preparing newly plastered surfaces & applying two coats of oil emulsion distempering(OBD) over and including a coat of white wallcare putty 2 mm thick over a coat of primer on walls 119 M&L for complete removal of existing treatment including cleaning of mortar drops, smoke soot, moulds, moss, efforsecent salt, trading oil grees spots etc using grinding machine on wall surfaces and preparation of old plastered wall surfaces and applying two coats of oil emulsion distemper ( OBD) of approved shed/tint over and including a coat of white wall care putty2 mm thick complete.over a coat of primer . 120 M&L for preparing newly plastered surfaces & applying three coat of white wash on ceiling complete all as specified and directed. 121 M&L for preparation of old surrfacesand applying two coats of white wash on ceiling complete all as specified and directed. 122 M&Lpreparing newly plastered surfaces of walls and applying two coats of exterior emulsion paint over a coat of 2mm thick exterior wall care putty on walls all complete all as specified and directed.Note:- Wall care putty shall be paid for separately under respective item. 123 M&L for preparing newly pastered surfaces of walls, plastered and applying 2mm thick exterior wall care putty on walls to prepare the surface even and smooth complete all as specified and directed. 124 M & L for writing letters or figures (Block, Roman, Itslic or Indian) n. exc 30 cm height with thick synthetic enamel paint. complete all as specified and as directed by Engr- in - Charge. 125 M&L for form work to soffits of suspended slabs such as roof slabs etc for rough finished concrete surface complete all as specified and directed. 126 M&L for form work to SIdes for slabs and SIdes of RCC/PCC bands in walls, horizontal or sloping and SImilar work exc 10 cm but n exc 20 cm wide for fair finished concrete surface complete all as specified and directed. 127 M&L for RCC 1:2:4 type B-1 (Nominal mix) using 20mm graded crushed stone aggregate as in roof, floor, slabs supported on walls complete all as specified and directed. 128 Dismantling structural steel work including doors, gates but excluding framed truss etc complete all as specified and directed. 129 Cutting Chases exe 10 cm but n exc 20cmin girth in brick/stone wall for fixing of PVC Pipe/GI pipe of 15 & 20mm bore (concealed in wall) including makink good surface in CM (1:6) & to match with the existing surfaces complete all as specified and directed. 130 M&L for cutting holes in stone /RCC/granite slabfor inserting coocking gas cylinder pipeand making good complete all as specified and directed. 131 S&F factory madekitchen cabinetof size 1.5M x 0.60M x 0.3M,made out of 18mm thick PVC celuka sheet having density not less than 650kg/cum one side decorative lamination & other side balancing lamination sheet consisting of carcase18 mm thick PVC sheetincluding shutters made out of 18 mm thick PVC boardall required brackets 5.5 screwes etc.The panels shall be fabricated using adhesive and screwswhere every required.All edge shall be covered with 2mm thick edge bonding tape or 90 degreeedge bent finish as per make and specification mentioned as per drawing and specification approved by Engineer-in-Charge.Note : (i)PVC celuka sheet manufactured by an ISO 9001-2015 certified company, termite proof, water proof & flame retradant PVC sheet. (ii) PVC cabinet of required size fabricated by joining four 18mm thick PVC celuka ply fixed with each other using solvent cement adhesive and screws and 18mm thick PVC sheet as backing of cabinet screw and solvent cement adhesive etc. (iii) The Cabinet box will be devided into twoequal part with two leafshutter and one shelf will be placed in cabinate (iv) Cabinate will be fixed in wall with4xfastners etc and necessary fixing lugs (v) Each shutter will be provided with SShandle 75 mm, CP Piano hinges, magnet/catcher(vi) The quoted ratesare included the rates of all fittings and fixturs 132 Supplying and fixing PVC Shutter for kitchen cainets and trolly shutter made of 18mm thick PVC Celluka ply having desity 600kg cbm density with prelaminated sheet on one side and other side balancing white inclu shutter. The PVC sheet shall be cut in desired shape and size put together and jointed with necessary adhesive and screws where required. all edges shall be covers with edge bonding tape of same colour. The shutters will be below kitchen counter with necessry fittings and fixtures complete all as specified and directed by engr in charge shutter will be provided with SS piano handle 75mm, continuous CP piano hinges and magnetic catcher. Note the Coated rated are included all fittings and fixtures complete all as specified and directed. 133 S&F for Pipe Supporting Clamping -for GI pipe 2 Nos for 15mm and 2 Nos for 20mmdown take pipe fixing done with Clamping System consists of Profile Bracket + Continuous Slotted C Channel + U Bolt R/M System running vertically with wall distance 3: Pipe Support Clamping made of 1. Profile Bracket having Wall Distance 3 made of Low Carbon Hot Roll Gauge Corrected (HRGC) Steel (IS 1079 DD); material size 32 mm x 3 mm with ribs and notch are Hot Dip Galvanzied + Zn Al Flake coated having Salt Spray Test (Test method - ASTM B-117-2019) result above 2000 hrs with SS304 Hex Flange Bolt with Serration 5/16 x 3/4 (A/F 13mm) as per DIN 6921and SS304 Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration as per DIN 6923. 2. Continuous Slotted C Channel with ribs to be used of size 10 made of Low Carbon Hot Roll Gauge Corrected (HRGC) steel (IS 1079 DD) are Hot Dip Galvanzied+ Zn Al Flake coated with material thickness of 3mm. 3. U bolt R/M are made of low carbon mild steel with Rod diameter 7 mm approx.; Zn Al Flake coated with noise absorbing semi transparent ribbed silicon rubber sleeve; with Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration set as per DIN 6923 - Zn Al Flake coated.Hotdip Galvanizing: As per IS 2629 (1985) - 610 grams/m2 (> 85 microns).Material Grade : IS 1079 DD used as per MTC confirms to EN 10204 3.1.Bracket Wall distance 3 - 2 Nos. 2. Continuous Slotted C Channel of Size 10 - 1 No.; 3. U Bolt R/M for 3 (75 mm) CI or PVC Pipe Dia. - 1 No.; and 4. Justi Khilla 2 1/2 Zn coated - 4 nos.Fixing Details: Pipe Support Clamping Unit to be fixed at every metre distance in the duct as specified in the Technical Drawing No. : CE Jaipur Zone - Jaipur; TD/2022/102.Make: Shaivi or equivalent as approved by GE. complete all as specified and directed 134 S&F for Pipe Supporting Clamping - Single Pipe of dia 3 (75 mm) down take pipe fixing done with Clamping System consists of Profile Bracket + Continuous Slotted C Channel + U Bolt R/M System running vertically with wall distance 3: Pipe Support Clamping made of 1. Profile Bracket having Wall Distance 3 made of Low Carbon Hot Roll Gauge Corrected (HRGC) Steel (IS 1079 DD); material size 32 mm x 3 mm with ribs and notch are Hot Dip Galvanzied + Zn Al Flake coated having Salt Spray Test (Test method - ASTM B-117-2019) result above 2000 hrs with SS304 Hex Flange Bolt with Serration 5/16 x 3/4 (A/F 13mm) as per DIN 6921and SS304 Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration as per DIN 6923. 2. Continuous Slotted C Channel with ribs to be used of size 10 made of Low Carbon Hot Roll Gauge Corrected (HRGC) steel (IS 1079 DD) are Hot Dip Galvanzied+ Zn Al Flake coated with material thickness of 3mm. 3. U bolt R/M are made of low carbon mild steel with Rod diameter 7 mm approx.; Zn Al Flake coated with noise absorbing semi transparent ribbed silicon rubber sleeve; with Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration set as per DIN 6923 - Zn Al Flake coated.Hotdip Galvanizing: As per IS 2629 (1985) - 610 grams/m2 (> 85 microns).Material Grade : IS 1079 DD used as per MTC confirms to EN 10204 3.1.Material Qty. for one unit : 1. Profile Bracket Wall distance 3 - 2 Nos. 2. Continuous Slotted C Channel of Size 10 - 1 No.; 3. U Bolt R/M for 3 (75 mm) CI or PVC Pipe Dia. - 1 No.; and 4. Justi Khilla 2 1/2 Zn coated - 4 nos.Fixing Details: Pipe Support Clamping Unit to be fixed at every metre distance in the duct as specified in the Technical Drawing No. : CE Jaipur Zone - Jaipur; TD/2022/102.Make: Shaivi or equivalent as approved by GE. complete all as specified and directed 135 S & F for Pipe Supporting Clamping - Single Pipe of dia 4 (110 mm) down take pipe fixing done with Clamping System consists of Profile Bracket + Continuous Slotted C Channel + U Bolt R/M System running vertically with wall distance 3: Pipe Support Clamping made of 1. Profile Bracket having Wall Distance 3 made of Low Carbon Hot Roll Gauge Corrected (HRGC) Steel (IS 1079 DD); material size 32 mm x 3 mm with ribs and notch are Hot Dip Galvanzied + Zn Al Flake coated having Salt Spray Test (Test method - ASTM B-117-2019) result above 2000 hrs with SS304 Hex Flange Bolt with Serration 5/16 x 3/4 (A/F 13mm) as per DIN 6921and SS304 Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration as per DIN 6923. 2. Continuous Slotted C Channel with ribs to be used of size 10 made of Low Carbon Hot Roll Gauge Corrected (HRGC) steel (IS 1079 DD) are Hot Dip Galvanzied+ Zn Al Flake coated with material thickness of 3mm. 3. U bolt R/M are made of low carbon mild steel with Rod diameter 7 mm approx.; Zn Al Flake coated with noise absorbing semi transparent ribbed silicon rubber sleeve; with Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration set as per DIN 6923 - Zn Al Flake coated.Hotdip Galvanizing: As per IS 2629 (1985) - 610 grams/m2 (> 85 microns). Material Grade : IS 1079 DD used as per MTC confirms to EN 10204 3.1.Material Qty. for one unit : 1. Profile Bracket Wall distance 3 - 2 Nos. 2. Continuous Slotted C Channel of Size 10 - 1 No.; 3. U Bolt R/M for 4 (110 mm) CI or PVC Pipe Dia. - 1 No.; and 4. Justi Khilla 2 1/2 Zn coated - 4 nos.Fixing Details: Pipe Support Clamping Unit to be fixed at every metre distance in the duct as specified in the Technical Drawing No. : CE Jaipur Zone - Jaipur; TD/2022/102.Make: Shaivi or equivalent as approved by GE. 136 Providing and fixing factory made uPVC white colour casement (Openable) window made of extruded profiles with wall thickness of 2.3mm ( + – 0.2mm). Window profile with hollow section with multi chamber, frame (60mm x 58mm), sash (60mm x 73mm),T profile (One vertical length in between two shutters) (60mm x 74mm), Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket 1.2 +– 0.2mm thick, galvanized steel Frame (28mm x 21.5mm), sash (31mm x 27.5mm). T profile (27mm x 17mm) to be inserted in required profile, frame will be fixed to the wall with 8 mm x 100mm long fasteners. Hardware: [casement handle made of zinc alloyed (white powder coated), But Hinges ofzinc alloyed (white powder coated), transmission gear made of mild steel with multi point locking system] and 5mm thick glazing with selected quality glass. Net opening will be measured for payment purpose. 137 M&L brick work with fly ash brick straight or curved on plan exc 6m mean radiusbuilt cement mortar 1:6 complete all as specified and as directed 138 M&L Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre complete all as specified and directed. 139 Providing and fixing Gypsum Board 12mm thick in ceiling fixed with screw as per manufacturers instructions complete all as specified and directed. 140 M&L for preparation of old/New surrfaces of ceilingand applying two coats of oil bound distemper on ceiling complete all as specified and directed. 141 S&F UPVC Partition / glass caldding wall made out UPVC frame work made using UPVC section of size 60 x 60X1.8 thick mm and Mullion Size60X78X1.8 mm Rainforced with necessary MS pipe .UPVC frame work divided in to squre n exe 1 sqm . 8 mm thick toughned glass to placed in frame with necessary EPDM rubber/ glazing clipe etc required to fit the glass complete all as specified and directed by GE / Engr in charge. Note: The quoted rate are including rate of galss and fittings and fixturers required for fixing the frame with wall/ MS pipe etc. 142 S& F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.5mm thick of an colourhaving tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed. 143 M&L Rooftrusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc, Wind ties etc grade Fe-410-W Quality A complete all as specified and directed. 144 S & F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes complete all as specified and directed. 145 Excavating in post holes ( or similar holes ) each n exc 0.5 cum getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering, and removing surplus soil to a distance n exc 50 mtr complete all as specified and directed. 146 M&L for plain cement concrete (1:2:4), type B-2, (using 40mm graded stone aggregate)in foundations, filling, mass concrete etc complete all as specified and directed. 147 M&L for two coats of synthetic enamel paint over a coat of Red oxide primer including preparation of new steel/iron surface of any description over 10 cm in width or girth complete all as specified and directed. 148 M&LSolid PVC Wall Lining consisting of 5mm thick wood grain printed PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing. 149 M&L for vitrified ceramic acrylic double charge tiles light shade 8-10mm thick (square/rectangular), polished, coloured, area of each tile not exceeding 0.36 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 20mm thick screed bed in cement & sand mortar 1:6 complete all as specified and directed. 150 M & L Hardcore of gauge n exc. 63 mm, brocken stone or boulder, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed. 151 Material & Labour for 75 mm thick Plain Cement concrete type D- 2, 1:4:8 (40mm graded aggregate) complete all as specified and as directed. 152 Taking down carefully copper/Aluminium point wiring for light/fan/socket/light fitting/power point and taking down of teak wood batten / PVC casing caping/PVC conduit/steel conduitand making good disturbed surfacesof walls/ceilings /floors etc incl dismentling of fittings complete all as specified and directed. 153 Taking down MCB with sheet metal enclosure, main switch, DB etc and making good disturbed surfaces to match with existing surfaces complete all as specified and directed. 154 Taking down sub main wiring of any size/capacity complete all as specified and making good disturbed surfaces to match with the existing surfaces 155 M&L for point wiring complete with 1.5 Sqmm single core multistranded copper conductor fire resistant low smoke and halogen (FRLSH) PVC insulated and unsheathed cable 1100 Volts grade confirming to IS-694 drawn through non metallic rigid PVC heavy duty conduit in concealed (min 20 mm external dia) but shall be increased as per actual site requirement in accordance with clause No. 19.125 of SSR Part-I ISI marked with wall thickness not less than 1.8 mm including conduit accessories like bends, tees, junction boxes etc fixed concealed/recessed in wall or ceiling including 1.5 mm FRLSH PVC insulated unsheathed copper earth wire including sunken type pressed steel terminal boxes electro plated of suitable size with bakellite white/coloured top sheet cover 3.0 mm thick for one light point controlled by one way switch including cutting chasis in stone/brick wall as required on sitecomplete all as specified and directed. 156 All as per srl item No 156.00 but for one fan point controlled by one switch and regulator 157 All as per srl item No 156.00 but for one exhaust fanpoint/Fresh Air Fan Point controlled by one switch . 158 All as per srl item No 156.00 but for one 3 pin 5/6 Amp socket outlet controlled by one 5 Amp switch on same board. 159 All as per srl item No 156.00 but for one 3 pin 5/6 Amp socket outlet controlled by one 5 Amp switch on independent board. 160 All as per srl item No 156.00 but for one bell/buzzerpoint controlled by one bell push 161 All as per srl item No 156.00 but for one lightpoint controlled two ,two way switches 162 All as per srl item No 156.00 but for one 3 pin 15/16 Amps socket outlet controlled by one 15/16 Amps switch on independent board with 2.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLSH cable 1100 Volt grade including 2.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLSH cable 1100 Volt grade as continuous earth wire in green colour. 163 All as per srl item No 156.00 but for one 3 pin 15/16 Amps socket outlet controlled by one 15/16 Amps switch on independent board with 4.0 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLSH cable 1100 Volt grade including 4.0 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLSH cable 1100 Volt grade as continuous earth wire in green colour. 164 Supply and fixing Modular switch, one way 6 Amp, 1 module, piano type, 230/250 volts grade on top covers (catered in point wiring above) complete all as specified and directed. 165 All as per srl item No 165.00 but for Modular switch, one way 16 Amp, 1 module 166 All as per srl item No 165.00 but for Modular bell push 6 Amp, 1 module 167 Supply and fix Modular socket outlet 2in1, 3pin 5A, 2 module, multipurpose use, flush mounting type, 230/250 Volts grade on Top covers (catered in point wiring above) complete all as specified and directed. 168 All as per srl item No 168.00 but for Modular socket outlet 2in1, 3 pin 15 Amps flush type 169 Supply and fixing switch piano, flush type, single pole, one way, 5/6 Amp, 230 Volts. 170 S&F switch piano flush type single pole two way 5 Amps 230 Volts . 171 S&F bell push flush type 5 Amps 240 V complete all as specified & directed. 172 S&F bell/buzzer AC 230 volts single polecomplete all as specified & directed. 173 Supply and fixing switch piano, flush type, single pole, one way, 15 Amp, 230 Volts. 174 Supply and fixing socket outlet, 3 pin (with 2 pin outlet also), 5/6 Amp, flush type, 240 Volts. 175 Supply and fixing socket outlet, 2 in 1, 3 pin, 5 and 15 Amp, flush type, 240 Volts. 176 Supply and fixing ceiling rose surface bakelite 65mmx50mm with two or three terminal complete all as specified. 177 Supply and fix fresh air fan 250 mm sweep 240 vot 50 Hz plastic body complete with louvers all as specified and direted by Engr-In-Charge 178 Supply and fix electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc complete all as specified and directed. 179 Supply and fix ceiling fan complete with electronic type regulator , copper winding and accessories 230v 1200mm sweep BEE 5 star rated with brushless direct current motor (BLDC) including taking down old unserviceable ceiling fan complete all as specified and directed by engineer-in-charge. 180 supply andfix exhaust fan metal bodyACsingle phase 230/240 V of size 300 mm sweep with louver including making suitable opening/hole in wallall as specified and directed by ebgineer-in-charge. 181 Supply and fix LED batten (1.2m) made of CRCA sheet housing with a PC glossy diffisure duly prewired connection having nominal system lumen output of 2000 lumens at a minimum system efficiency of 115 lumen per watt and total power consumption not more than 20 watt including driver. it should have rated system life time of 40000 burning hours at L70 and should have a temperature of 6500 K CRI >80, thd <10 and PF>0.95 complete all as specified and directed. Make - Crompton Cat Part CIS-305-40-57-SL-DP-NWH, Philips Cat part BN308C LED20S-6500 L120 PSU WH, Havells Cat Part STOUTPLUS600BS20WLED840SPCWH 182 Supply & fix in repair recess type, 36 watt LED panel light (600x600 mm) complete with fittings integrated electronic driver,energy efficient, 230 volts,co- relatedcolour temperature (CCT) of 6500K, warm white/ cool white/natural white complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable of suitable size complete all as specified and directed by Enginee-in-Charge. MAKE- Havels, Philips, Bajaj 183 Supply and fixing lamp holder PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified. 184 Supply and Fixing 20 watt emergency LED inverter bulb B-22 capacity with inbuilt powerful lithium battery backup of atleast 4 hours and having minimum two years warranty. The lighting shall have deep discharge protection, fast charging, offering cool day light for atleast four hours in off hours.Make : - Havells/Philips/Bajaj 185 Supply and fixing sheet metal enclosuresdouble door type suitable for fixing MCBs, SPN with 200 Amps rated bus bar,8 way, 240 Volts. 186 S & F MCB 32/40 Amp, single pole & neutral,240 Volt complete all as pecified & directed. 187 S & F MCB 6-40 Amp, single pole240 Volt complete all as pecified & directed. 188 Supply and fixing Vertical sheet metalenclosures double door type , suitable for fixing MCB,TPN with 200 amps rated bus bar , 4 way. 415 Volts with inbuilt MCCB 4 pole 63 Amp,16 KA complete all as specified and directed. 189 S&F sub main wiring on and includingpassing through PVC conduit in concealed (including cutting chasis in stone/brick wall) 1100 Volts grade with PVC flexible cable copper conductor cablefire resistant low smoke and halogen (FRLSH) unsheathed multistranded single core of size 6 sqmm and continuous earth with PVC flexible cable copper conductorunsheathed multistranded single core of size 6 sqmm of green colour confirming to IS 694/1990 including taking down existing U/S sub main wiring. (Note:Two runs of cable with one run of earth wire and one run of PVC Coundit shouldmeasured as one length) 190 Material and labour for earthing complete with galvanized steel earth plate electrode 60cmx60cmx6mm thick burried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of plate not less than 1.5 m deep below normal ground level and connected to and including galvanized iron earth wire 4 mm dia by means of GI nuts, bolts, check nuts, washers thimbles, etc as shown in electrical plate No 3 of SSR Part-I and connection to main switch board/Test point/panel/equipment and testing on completion including excavation and earth work in any type of soil, returning filling in, and removal of surplus spoil to a distance not exc 50 metre, charcoal and salt in alternate layer 15 cm thick all around the earth plate electrode, MS funnel with wire mesh, GI pipe medium grade 20 mm bore for watering and 15 mm bore 3.00 metre long GI pipe light grade for earth wire protection fixed with poles with two clamps, made from MS flat 25 mmx3mm, bolts, nuts and washers,PCCchamber (1:3:6) type C1, 40mm thick precast RCC cover 1:2:4 type B1 shall be provided on CI frame etc complete all as specified &directed.Note : - Quoted rate shall be deemed to include for earth wire with protection pipe up to 7.5 meter length. 191 M/L for GI pipe ( Light grade ) for protection of LT cable fixed to walls/ poles/road crossing including clamps complete of 40 mm bore complete all as specified and directed. 192 Supply and fixing in repair of GI water tubing IS-1239 marked, medium grade, in replacement including all necessary pipe fittingslaid in trenches, on wall, under floor, under road on same or new route and making good the disturbed portion as existing and including taking down of old unserviciable pipe of the size 25 mm bore complete all as specified and directed.
